ZHX1200 Low-Power SIR (IrMC) Transceiver Product Specification PS007107-1101 ZiLOG Worldwide Headquarters • 910 E. Hamilton Avenue • Campbell, CA 95008 Telephone: 408.558.8500 • Fax: 408.558.8300 • www.ZiLOG.com This publication is subject to replacement by a later edition. To determine whether a later edition exists, or to request copies of publications, contact: ZiLOG Worldwide Headquarters 910 E. Hamilton Avenue Campbell, CA 95008 Telephone: 408.558.8500 Fax: 408.558.8300 www.ZiLOG.com ZiLOG is a registered trademark of ZiLOG Inc. in the United States and in other countries. All other products and/or service names mentioned herein may be trademarks of the companies with which they are associated. Document Disclaimer ©2001 by ZiLOG, Inc. All rights reserved. Information in this publication concerning the devices, applications, or technology described is intended to suggest possible uses and may be superseded. ZiLOG, INC. DOES NOT ASSUME LIABILITY FOR OR PROVIDE A REPRESENTATION OF ACCURACY OF THE INFORMATION, DEVICES, OR TECHNOLOGY DESCRIBED IN THIS DOCUMENT. ZiLOG ALSO DOES NOT ASSUME LIABILITY FOR INTELLECTUAL PROPERTY INFRINGEMENT RELATED IN ANY MANNER TO USE OF INFORMATION, DEVICES, OR TECHNOLOGY DESCRIBED HEREIN OR OTHERWISE. Devices sold by ZiLOG, Inc. are covered by warranty and limitation of liability provisions appearing in the ZiLOG, Inc. Terms and Conditions of Sale. ZiLOG, Inc. makes no warranty of merchantability or fitness for any purpose. Except with the express written approval of ZiLOG, use of information, devices, or technology as critical components of life support systems is not authorized. No licenses are conveyed, implicitly or otherwise, by this document under any intellectual property rights. PS007107-1101 ZHX1200 Low-Power SIR (IrMC) Transceiver iii Table of Contents Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Pin Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VCC Positive Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GND Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TAB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TXD Transmit Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RXD Receive Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SD Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LEDA IRED Driver Anode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 4 4 4 4 5 5 5 Electrical and Timing Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Transceiver Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Mechanical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Pad Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Recommended Soldering Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Packing, Storing, and Baking Recommendations . . . . . . . . . . . . . . . . . . . . . . . 17 Moisture Prevention Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Baking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Taping Specifications (in accordance with JIS C 0806) . . . . . . . . . . . . . . . . . . 18 Customer Feedback Form . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Customer Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Product Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Return Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Problem Description or Suggestion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PS007107-1101 20 20 20 20 20 ZHX1200 Low-Power SIR (IrMC) Transceiver iv List of Figures Figure 1. Figure 2. Figure 3. Figure 4. Figure 5. Figure 6. Figure 7. Figure 8. Figure 9. Figure 10. Figure 11. Figure 12. Figure 13. Figure 14. Figure 15. Figure 16. IrMC Transceiver Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 ZHX1200 Application Block Diagrams . . . . . . . . . . . . . . . . . . . . . . . . 3 Truth Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Transmitter Current Versus LED Voltage (Ta=25 °C) . . . . . . . . . . . 10 Transmitter Current Versus Supply Voltage (Ta=25 °C) . . . . . . . . . 10 Radiant Intensity Versus Transmitter Current (Ta=25 °C) . . . . . . . . 11 Receive Current Versus Supply Voltage (Ta=25 °C) . . . . . . . . . . . . 11 LED Relative Radiant Power Versus Wavelength (Ta=25 °C) . . . . 12 Photodiode Relative Radiant Sensitivity Versus Wavelength (Ta=25 °C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Relative Forward Voltage Versus Ambient (IF=35 mA) . . . . . . . . . . 13 ZHX1200 Mechanical Specifications . . . . . . . . . . . . . . . . . . . . . . . . 14 ZHX1200 Pad Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Temperature Profile for the Top Surface . . . . . . . . . . . . . . . . . . . . . 16 IrMC Transceiver Packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Reel Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Tape Dimensions and Configuration . . . . . . . . . . . . . . . . . . . . . . . . 19 List of Tables Table 1. Table 2. Table 3. Table 4. Table 5. PS007107-1101 IrMC Transceiver Pin Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Recommended Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Truth Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 6 6 7 9 ZHX1200 Low-Power SIR (IrMC) Transceiver 1 Description The ZiLOG ZHX1200 is the transceiver of choice for mobile communication applications in today’s ultra compact, power-conscious, portable products, such as mobile phones, pagers, or personal data assistants (PDAs). Specifically designed to support Infrared Data Association (IrDA) IrMC low-power SIR (serial infrared) mode, the transceiver combines an infrared emitting diode (IRED) emitter, a PIN photodiode detector, a digital AC-coupled LED driver, and a receiver/decoder in a single, miniature package. The ZiLOG ZHX1200 provides an efficient implementation of the low-power SIR standard in a small footprint format. Application circuit space is also minimized, as only one capacitor is required to complete the solution. Features • • • • • • • • • PS007107-1101 Compliant to the IrDA Specification Low-Power SIR Low supply voltage range, 2.7 to 3.6 V 0.2 µA (maximum) shutdown Low power, 95 µA (typical) at 3.3 V Ultra small form factor (6.8 mm long x 2.8 mm wide x 2.2 mm high) External components: one resistor and one capacitor Extended operating temperature range (–30 °C to +85 °C) ILED=35 mA at 3.6 mW/sr Meets IEC 825-1 Class 1 Eye Safety Specifications ZHX1200 Low-Power SIR (IrMC) Transceiver 2 Block Diagram Figure 1 is the block diagram for the IrMC Transceiver. Figure 1. IrMC Transceiver Block Diagram Figure 2 shows a typical application of the IrMC transceiver. PS007107-1101 ZHX1200 Low-Power SIR (IrMC) Transceiver 3 Figure 2. ZHX1200 Application Block Diagrams PS007107-1101 ZHX1200 Low-Power SIR (IrMC) Transceiver 4 Pin Description Table 1 lists the pin out for the IrMC transceiver. The pins are described in this section. Table 1. IrMC Transceiver Pin Out Pin Name Function I/O 1 VCC Supply voltage — 2 GND Ground — 3 SD Enables SD mode I 4 RXD Receiver output O 5 TXD Transmitter input I 6 LEDA IRED anode — — TAB Shield ground — VCC Positive Supply (Power) Connect to positive power supply (2.7–3.6 V). Place a 0.33-µF ceramic bypass capacitor as close as possible to the VCC pin. GND Ground (Power) Connect to ground of the power supply. A solid ground plane is recommended for proper operation. TAB (Shield) The Shield tab must be soldered to the ground plane. TXD Transmit Data (Input, active high) This CMOS input is used to transmit serial data. PS007107-1101 ZHX1200 Low-Power SIR (IrMC) Transceiver 5 This input has an internal pull-down resistor that is disabled (open-circuited) during shutdown. TXD has integrated digital AC coupling; therefore, no external AC-coupling components are required for input signals between GND and VCC. RXD Receive Data (Output, active low) This output indicates received serial data. It is a tri-state, slew rate controlled CMOS output (tri-stated during shutdown) driver capable of driving a standard CMOS or LSTTL load. No external resistor is required. SD Shutdown (Input, active high) This input is used to place the integrated circuit into shutdown mode. Maximum current draw in shutdown mode is 0.2 µA. Module shutdown current might be limited by the choice of capacitor used from VCC1 to ground. LEDA IRED Driver Anode (Power) This output is internally connected to the LED anode and is connected to the supply voltage. Current to the LED must be limited to a maximum of 50 mA (20% duty cycle maximum). The voltage range on this pad is 2.7–3.6 volts. PS007107-1101 ZHX1200 Low-Power SIR (IrMC) Transceiver 6 Electrical and Timing Specifications Table 2, Table 3, and Table 4 list the electrical and timing specifications. Table 2. Absolute Maximum Ratings Parameter Symbol Min Max Unit Comment Supply voltage VCC 0 7.0 V VCC, GND Input voltage VIN GND–0.3 VCC+0.3 V TxD, SD Output (Ext.) voltage VOUT GND–0.3 VCC+0.3 V RxD LED current IPULSE 50 mA 20% duty cycle, Ta=25 °C, tON<90 µS Storage temperature TST 100 °C Solder temperature TSOL 260 °C –40 Table 3. Recommended Operating Conditions PS007107-1101 Parameter Symbol Min Max Unit Supply voltage VCC 2.7 3.6 V Ambient operating temperature TOP –30 85 °C ZHX1200 Low-Power SIR (IrMC) Transceiver 7 Table 4. Electrical Characteristics Parameter Symbol Condition High-level input voltage VIH Low-level input voltage VIL High-level output voltage VOH IOH=20 µA Low-level output voltage VOL IOL=400 µA Min Typical Max 0.75VCC 0.4 VCC–0.3 0.3 35 Transmitter current ILED Unit Remarks V TxD, SD V TxD, SD V RxD V RxD mA 120 µA SD=0 V, TxD=0 V 0.2 µA SD=VCC, TxD=0 V 40 200 nS 1.6 2.0 µS 1 µS TSTU 100 µS Latency (3) TRRT 60 µS Trans. radiant. intensity (4) IE ILED=35 mA 28 mW/sr θh, θv<(+15°) Minimum threshold irradiance (5) Eemin VCC=3.3 V 8.1 µW/cm2 θh, θv<(+15°) Maximum input irradiance Eemax VCC=3.3 V Receive current IS Standby current ISTB Optical rise/fall time tRrtRf RxD pulse width TPWA VCC=3.3 V SIR=115 Kbps 95 1.0 Shutdown time (1) TSD Startup time (2) 3.6 500 Unless otherwise noted: VCC=3.3 V, GND=0 V, TA=+25 °C (1) The time to go into standby mode after SD is high (2) The time to revert to active mode after SD is low (3) Time required to shift from transmit to receive (4) θh is the horizontal angle; θv is the vertical angle. (5) Noise dependent (6) Time LED stays on when TxD is left high PS007107-1101 mW/cm2 θh, θv<(+15°) ZHX1200 Low-Power SIR (IrMC) Transceiver 8 Table 4. Electrical Characteristics (Continued) Parameter Symbol Angle of half intensity θ Light pulse rise, fall time tortof Optical pulse width (6) tOPW Optical overshoot tOPO Peak wavelength λρ Condition Min Unless otherwise noted: VCC=3.3 V, GND=0 V, TA=+25 °C (1) The time to go into standby mode after SD is high (2) The time to revert to active mode after SD is low (3) Time required to shift from transmit to receive (4) θh is the horizontal angle; θv is the vertical angle. (5) Noise dependent (6) Time LED stays on when TxD is left high PS007107-1101 Typical Max 20 200 Remarks ° Hor. and vert. nS µS 20 25 870 Unit % nm TxD=“H” ZHX1200 Low-Power SIR (IrMC) Transceiver 9 Table 5 and Figure 3 show the truth table for the IrMC transceiver. Table 5. Truth Table Input Output SD TxD Ee Ir(LED) RxD VIL VIH X High(On) NV VIL VIL EeIH Low(Off) Low VIH VIH X Low(Off) High VIH VIL X Low(Off) High X: Don’t care NV: Not valid Ee: Input irradiance present at detector surface EeIH: 8.1 µW/cm2<Ee<500 mW/cm2 Figure 3. Truth Table PS007107-1101 ZHX1200 Low-Power SIR (IrMC) Transceiver 10 Transceiver Performance Figure 4 through Figure 10 show the performance of the IrMC transceiver. Figure 4. Transmitter Current Versus LED Voltage (Ta=25 °C) Figure 5. Transmitter Current Versus Supply Voltage (Ta=25 °C) PS007107-1101 ZHX1200 Low-Power SIR (IrMC) Transceiver 11 Figure 6. Radiant Intensity Versus Transmitter Current (Ta=25 °C) Figure 7. Receive Current Versus Supply Voltage (Ta=25 °C) PS007107-1101 ZHX1200 Low-Power SIR (IrMC) Transceiver 12 Figure 8. LED Relative Radiant Power Versus Wavelength (Ta=25 °C) Figure 9. Photodiode Relative Radiant Sensitivity Versus Wavelength (Ta=25 °C) PS007107-1101 ZHX1200 Low-Power SIR (IrMC) Transceiver 13 Figure 10. Relative Forward Voltage Versus Ambient (IF=35 mA) PS007107-1101 ZHX1200 Low-Power SIR (IrMC) Transceiver 14 Mechanical Specifications Figure 11 shows the mechanical specifications for the IrMC transceiver. Note: The ZiLOG ZHX1200 transceiver will continue to show the original Calibre part number, CHX1200. Figure 11. ZHX1200 Mechanical Specifications PS007107-1101 ZHX1200 Low-Power SIR (IrMC) Transceiver 15 Pad Layout Figure 12 shows the ZHX1200 pad layout. 0.95 0.5 6) LEDA 5) TxD 4) RxD 3) SD 2) GND 2.33 1) VCC CL 1.75 0.75 Shield ground 2.30 Figure 12. ZHX1200 Pad Layout PS007107-1101 ZHX1200 Low-Power SIR (IrMC) Transceiver 16 Recommended Soldering Conditions Follow these recommendations to maintain the performance of the ZHX1200 transceiver. • With the soldering iron: Temperature at tip: no more than 280 °C Time: 3 seconds maximum • Reflow: Preheat: 120 °C to 150 °C, 60 to 120 seconds Soldering: 230 °C, within 10 seconds Heating up and cooling down: 5 °C/second Number of soldering times: 2 times maximum • The temperature profile at the top surface of ZHX1200, shown in Figure 13, is recommended. Figure 13. Temperature Profile for the Top Surface PS007107-1101 ZHX1200 Low-Power SIR (IrMC) Transceiver 17 Packing, Storing, and Baking Recommendations Follow these recommendations to maintain the performance of the ZHX1200 transceiver. Moisture Prevention Guidelines In order to avoid moisture absorption during transportation and storage, ZHX1200 reels are packed in aluminum envelopes (see Figure 14) that contain a desiccant with a humidity indicator. While this packaging is an impediment to moisture absorption, it is by no means absolute, and no warranty is implied. The user should store these parts in a controlled environment to prevent moisture entry. Please read the label on the aluminum bag for indicator instructions. ALUMINUM ENVELOPE DESICCANT REEL LABEL Figure 14. IrMC Transceiver Packaging Baking Parts that have been stored over 12 months or unpacked over 72 hours must be baked under the following guidelines. Reels 60 °C for 48 hours or more Loose Parts • 100 °C for 4 hours or more or • 125 °C for 2 hours or more or • PS007107-1101 150 °C for 1 hour or more ZHX1200 Low-Power SIR (IrMC) Transceiver 18 Taping Specifications (in accordance with JIS C 0806) Figure 15 shows the reel dimensions, and Figure 16 shows the tape dimensions and configuration. 330 DIA. DETAIL 80 ± 1 DIA. 2.0 ± 0.5 R 1.0 LABEL PASTED HERE 21.0 ± 0.8 13.0 ± 0.5 (Unit:mm) Figure 15. Reel Dimensions PS007107-1101 17.5 +- 2.0 0.0 2 ± 0.5 ZHX1200 Low-Power SIR (IrMC) Transceiver 19 Figure 16. Tape Dimensions and Configuration PS007107-1101 ZHX1200 Low-Power SIR (IrMC) Transceiver 20 Customer Feedback Form If you experience any problems while operating this product, or if you note any inaccuracies while reading this product specification, please copy and complete this form, then mail or fax it to ZiLOG (see Return Information, below). We also welcome your suggestions! Customer Information Name Country Company Phone Address Fax City/State/Zip email Product Information Serial # or Board Fab #/Rev # Software Version Document Number Host Computer Description/Type Return Information ZiLOG System Test/Customer Support 910 E. Hamilton Avenue, Suite 110, MS 4–3 Campbell, CA 95008 Fax: (408) 558-8536 Email: [email protected] Problem Description or Suggestion Provide a complete description of the problem or your suggestion. If you are reporting a specific problem, include all steps leading up to the occurrence of the problem. Attach additional pages as necessary. _______________________________________________________________________________ _______________________________________________________________________________ _______________________________________________________________________________ _______________________________________________________________________________ PS007107-1101