Y5V Dielectric General Specifications Y5V formulations are for general-purpose use in a limited temperature range. They have a wide temperature characteristic of +22% –82% capacitance change over the operating temperature range of –30°C to +85°C. Y5V’s high dielectric constant allows the manufacture of the highest capacitance value in a given case size. These characteristics make Y5V ideal for decoupling applications within limited temperature range. PART NUMBER (see page 3 for complete part number explanation) 0805 3 G 104 Z A T 2 A Size (L" x W") Voltage 10V = Z 16V = Y 25V = 3 50V = 5 Dielectric Y5V = G Capacitance Code Capacitance Tolerance Z = +80 –20% Failure Rate A = Not Applicable Terminations T = Plated Ni and Solder Packaging 2 = 7" Reel 4 = 13" Reel Special Code A = Std. Product PERFORMANCE CHARACTERISTICS Capacitance Range Capacitance Tolerances Operating Temperature Range Temperature Characteristic Voltage Ratings Dissipation Factor Insulation Resistance (+25°C, RVDC) Dielectric Strength Test Voltage Test Frequency 16 2200 pF to 22 µF +80 –20% –30°C to +85°C +22% to –82% max. within operating temperature 10, 16, 25 and 50 VDC (+85°C) For 50 volts: 5.0% max. For 16 and 25 volts: 7% max. For 10 volts: 10% max. 10,000 megohms min. or 1000 MΩ - µF min., whichever is less 250% of rated voltage for 5 seconds at 50 mamp max. current 1.0 Vrms ± 0.2 Vrms 1 KHz Y5V Dielectric Typical Characteristic Curves** 0.1 F - 0603 Impedance vs. Frequency Temperature Coefficient 10,000 1,000 100 |Z| (Ohms) % ⌬ Capacitance +20 +10 0 -10 -20 -30 -40 -50 -60 -70 -80 10 1 0.1 -55 -35 -15 0.01 10,000 +5 +25 +45 +65 +85 +105 +125 Temperature °C 100,000 1,000,000 10,000,000 Frequency (Hz) 0.22 F - 0805 Impedance vs. Frequency Capacitance Change vs. DC Bias Voltage 1,000 +40 100 |Z| (Ohms) ⌬ c/c (%) +20 0 -20 -40 -60 10 1 0.1 -80 -100 0 20 40 60 80 0.01 10,000 100 Insulation Resistance vs. Temperature 1,000,000 10,000,000 1 F - 1206 Impedance vs. Frequency 10,000 1,000 100 1,000 |Z| (Ohms) Insulation Resistance (Ohm-Farads) 100,000 Frequency (Hz) DC Bias Voltage 100 10 1 0.1 0 +20 +30 +40 +50 +60 +70 0.01 10,000 +80 +85 Temperature °C 100,000 1,000,000 10,000,000 Frequency (Hz) SUMMARY OF CAPACITANCE RANGES VS. CHIP SIZE Style 0402* 0603* 0805* 1206* 1210* 1812* 1825* 2220 2225 10V 2.2nF - 0.1µF 2.2nF - 1µF 10nF - 4.7µF 10nF - 10µF 10nF - 22µF → → — → 16V 2.2nF - 0.1µF 2.2nF - 0.33µF 10nF - 2.2µF 10nF - 4.7µF 0.1µF - 10µF → → — → 25V 2.2nF - 22nF 2.2nF - 0.22µF 10nF - 1µF 10nF - 2.2µF 0.1µF - 4.7µF 0.15µF - 1.5µF 0.47µF - 1.5µF — 0.68µF - 2.2µF 50V 2.2nF - 10nF 2.2nF - 56nF 10nF - 0.33µF 10nF - 1µF 0.1µF - 1µF 1.5nF - 1.5µF 0.47µF - 1.5µF 1µF - 1.5µF 0.68µF - 1.5µF * Standard Sizes ** For additional information on performance changes with operating conditions consult AVX’s software SpiCap. 17 Y5V Dielectric Capacitance Range PREFERRED SIZES ARE SHADED 1.00 ± .10 (.040 ± .004) .50 ± .10 (.020 ± .004) .60 (.024) .25 ± .15 (.010 ± .006) 1.60 ± .15 (.063 ± .006) .81 ± .15 (.032 ± .006) .90 (.035) .35 ± .15 (.014 ± .006) MM (in.) MM (in.) MM (in.) MM (in.) (L) Length (W) Width (T) Max. Thickness (t) Terminal WVDC 10 16 25 50 10 16 25 1210 2.01 ± .20 (.079 ± .008) 1.25 ± .20 (.049 ± .008) 1.30 (.051) .50 ± .25 (.020 ± .010) 50 10 16 25 3.20 ± .20 (.126 ± .008) 1.60 ± .20 (.063 ± .008) 1.50 (.059) .50 ± .25 (.020 ± .010) 50 10 16 25 3.20 ± .20 (.126 ± .008) 2.50 ± .20 (.098 ± .008) 1.70 (.067) .50 ± .25 (.020 ± .010) 50 10 16 25 50 1812* 1825* 2220* 2225* All Embossed All Embossed All Embossed All Embossed 4.50 ± .30 (.177 ± .012) 3.20 ± .20 (.126 ± .008) 1.70 (.067) .61 ± .36 (.024 ± .014) 4.50 ± .30 (.252 ± .016) 6.40 ± .40 (.252 ± .016) 1.70 (.067) .61 ± .36 (.024 ± .014) 5.7 ± 0.4 (.225 ± .016) 5.0 ± 0.4 (.197 ± .016) 2.30 (.090) .64 ± .39 (.025 ± .015) 5.72 ± .25 (.225 ± .010) 6.35 ± .25 (.250 ± .010) 1.70 (.067) .64 ± .39 (.025 ± .015) 25 25 50 50 䉲 2200 2700 3300 1206 50 25 䉲 Cap (pF) 0805 Paper/Embossed Paper/Embossed Paper/Embossed L W 䉲 䉲 Cap (µF) T 䉲 3900 4700 5600 6800 8200 50 䉲 0603* All Paper 䉲 0402* All Paper 䉲 SIZE Standard Reel Packaging t .01 .012 .015 .018 .022 .027 .033 .039 .047 .056 .068 .082 .10 .12 .15 .18 .22 .27 .33 .39 .47 .56 .68 .82 1.0 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10.0 12.0 15.0 18.0 22.0 *Reflow soldering only. = Paper Tape NOTES: For low profile product, see page 19. 18 = Embossed Tape How to Order Part Number Explanation EXAMPLE: 08055A101JAT2A 0805 Size (L" x W") 0402 0504 0603 0805 1005 0907 1206 1210 1505 1805 1808 1812 1825 2225 3640 5 A 101 Dielectric C0G (NP0) = A X7R = C X5R = D Z5U = E Y5V = G Voltage 10V = Z 16V = Y 25V = 3 50V = 5 100V = 1 200V = 2 250V = V 500V = 7 600V = C 1000V = A 1500V = S 2000V = G 2500V = W 3000V = H 4000V = J 5000V = K J C D F G J K M Z P A Capacitance Tolerance = ±.25 pF* = ±.50 pF* = ±1% (≥ 25 pF) = ±2% (≥ 13 pF) = ±5% = ±10% = ±20% = +80%, -20% = +100%, -0% Capacitance Code (2 significant digits + no. of zeros) Examples: 10 pF = 100 100 pF = 101 1,000 pF = 102 22,000 pF = 223 220,000 pF = 224 1 µF = 105 For values below 10 pF, use “R” in place of decimal point, e.g., 9.1 pfd = 9R1. T 2 Terminations Standard: T = Ni and Tin Plated Others: 7 = Plated Ni Gold Plated 1 = Pd/Ag Failure Rate A = Not Applicable A Special** Code A = Standard Product Non-Standard P = Embossed unmarked M = Embossed marked E = Standard packaging marked Low Profile Chips Only Max. Thickness T = .66mm (.026") S = .56mm (.022") R = .46mm (.018") Packaging** Recommended: 2 =7" Reel 4 =13" Reel Others: 7 = Bulk Cassette 9 = Bulk * C&D tolerances for ⱕ10 pF values. ** Standard Tape and Reel material depends upon chip size and thickness. See individual part tables for tape material type for each capacitance value. Note: Unmarked product is standard. Marked product is available on special request, please contact AVX. Standard packaging is shown in the individual tables. Non-standard packaging is available on special request, please contact AVX. 3 Surface Mounting Guide MLC Chip Capacitors Component Pad Design Component pads should be designed to achieve good solder filets and minimize component movement during reflow soldering. Pad designs are given below for the most common sizes of multilayer ceramic capacitors for both wave and reflow soldering. The basis of these designs is: • Pad width equal to component width. It is permissible to decrease this to as low as 85% of component width but it is not advisable to go below this. • Pad overlap 0.5mm beneath component. • Pad extension 0.5mm beyond components for reflow and 1.0mm for wave soldering. REFLOW SOLDERING D2 D1 D3 D4 D5 Dimensions in millimeters (inches) Case Size 0402 0603 0805 1206 1210 1808 1812 1825 2220 2225 D1 D2 D3 D4 D5 1.70 (0.07) 2.30 (0.09) 3.00 (0.12) 4.00 (0.16) 4.00 (0.16) 5.60 (0.22) 5.60 (0.22) 5.60 (0.22) 6.60 (0.26) 6.60 (0.26) 0.60 (0.02) 0.80 (0.03) 1.00 (0.04) 1.00 (0.04) 1.00 (0.04) 1.00 (0.04) 1.00 (0.04)) 1.00 (0.04) 1.00 (0.04) 1.00 (0.04) 0.50 (0.02) 0.70 (0.03) 1.00 (0.04) 2.00 (0.09) 2.00 (0.09) 3.60 (0.14) 3.60 (0.14) 3.60 (0.14) 4.60 (0.18) 4.60 (0.18) 0.60 (0.02) 0.80 (0.03) 1.00 (0.04) 1.00 (0.04) 1.00 (0.04) 1.00 (0.04) 1.00 (0.04) 1.00 (0.04) 1.00 (0.04) 1.00 (0.04) 0.50 (0.02) 0.75 (0.03) 1.25 (0.05) 1.60 (0.06) 2.50 (0.10) 2.00 (0.08) 3.00 (0.12) 6.35 (0.25) 5.00 (0.20) 6.35 (0.25) 41 Surface Mounting Guide MLC Chip Capacitors WAVE SOLDERING Case Size 0603 0805 1206 1210 D2 D1 D3 D4 D1 D2 D3 D4 D5 3.10 (0.12) 4.00 (0.15) 5.00 (0.19) 5.00 (0.19) 1.20 (0.05) 1.50 (0.06) 1.50 (0.06) 1.50 (0.06) 0.70 (0.03) 1.00 (0.04) 2.00 (0.09) 2.00 (0.09) 1.20 (0.05) 1.50 (0.06) 1.50 (0.06) 1.50 (0.06) 0.75 (0.03) 1.25 (0.05) 1.60 (0.06) 2.50 (0.10) D5 Dimensions in millimeters (inches) Component Spacing Preheat & Soldering For wave soldering components, must be spaced sufficiently far apart to avoid bridging or shadowing (inability of solder to penetrate properly into small spaces). This is less important for reflow soldering but sufficient space must be allowed to enable rework should it be required. The rate of preheat should not exceed 4°C/second to prevent thermal shock. A better maximum figure is about 2°C/second. For capacitors size 1206 and below, with a maximum thickness of 1.25mm, it is generally permissible to allow a temperature differential from preheat to soldering of 150°C. In all other cases this differential should not exceed 100°C. For further specific application or process advice, please consult AVX. ≥1.5mm (0.06) ≥1mm (0.04) ≥1mm (0.04) 42 Cleaning Care should be taken to ensure that the capacitors are thoroughly cleaned of flux residues especially the space beneath the capacitor. Such residues may otherwise become conductive and effectively offer a low resistance bypass to the capacitor. Ultrasonic cleaning is permissible, the recommended conditions being 8 Watts/litre at 20-45 kHz, with a process cycle of 2 minutes vapor rinse, 2 minutes immersion in the ultrasonic solvent bath and finally 2 minutes vapor rinse. Surface Mounting Guide MLC Chip Capacitors APPLICATION NOTES General Good solderability is maintained for at least twelve months, provided the components are stored in their “as received” packaging at less than 40°C and 70% RH. Surface mounting chip multilayer ceramic capacitors are designed for soldering to printed circuit boards or other substrates. The construction of the components is such that they will withstand the time/temperature profiles used in both wave and reflow soldering methods. Solderability Handling Terminations to be well soldered after immersion in a 60/40 tin/lead solder bath at 235 ±5°C for 2±1 seconds. Chip multilayer ceramic capacitors should be handled with care to avoid damage or contamination from perspiration and skin oils. The use of tweezers or vacuum pick ups is strongly recommended for individual components. Bulk handling should ensure that abrasion and mechanical shock are minimized. Taped and reeled components provides the ideal medium for direct presentation to the placement machine. Any mechanical shock should be minimized during handling chip multilayer ceramic capacitors. Storage Leaching Terminations will resist leaching for at least the immersion times and conditions shown below. Termination Type Nickel Barrier Solder Solder Tin/Lead/Silver Temp. °C 60/40/0 260±5 Immersion Time Seconds 30±1 Preheat Recommended Soldering Profiles Reflow 300 Natural Cooling Preheat Solder Temp. 250 200 220°C to 250°C 150 Soldering 100 50 0 1min 10 sec. max 1min (Minimize soldering time) Wave Preheat Natural Cooling 250 Solder Temp. Mildly activated rosin fluxes are preferred. The minimum amount of solder to give a good joint should be used. Excessive solder can lead to damage from the stresses caused by the difference in coefficients of expansion between solder, chip and substrate. AVX terminations are suitable for all wave and reflow soldering systems. If hand soldering cannot be avoided, the preferred technique is the utilization of hot air soldering tools. Cooling 300 200 It is important to avoid the possibility of thermal shock during soldering and carefully controlled preheat is therefore required. The rate of preheat should not exceed 4°C/second and a target figure 2°C/second is recommended. Although an 80°C to 120°C temperature differential is preferred, recent developments allow a temperature differential between the component surface and the soldering temperature of 150°C (Maximum) for capacitors of 1210 size and below with a maximum thickness of 1.25mm. The user is cautioned that the risk of thermal shock increases as chip size or temperature differential increases. T 230°C to 250°C 150 100 50 0 1 to 2 min 3 sec. max (Preheat chips before soldering) T/maximum 150°C Natural cooling in air is preferred, as this minimizes stresses within the soldered joint. When forced air cooling is used, cooling rate should not exceed 4°C/second. Quenching is not recommended but if used, maximum temperature differentials should be observed according to the preheat conditions above. Cleaning Flux residues may be hygroscopic or acidic and must be removed. AVX MLC capacitors are acceptable for use with all of the solvents described in the specifications MIL-STD202 and EIA-RS-198. Alcohol based solvents are acceptable and properly controlled water cleaning systems are also acceptable. Many other solvents have been proven successful, and most solvents that are acceptable to other components on circuit assemblies are equally acceptable for use with ceramic capacitors. 43 Packaging of Chip Components Automatic Insertion Packaging TAPE & REEL QUANTITIES All tape and reel specifications are in compliance with RS481. 8mm Paper or Embossed Carrier (1) 12mm 0805, 1005, 1206, 1210 Embossed Only 0504, 0907 Paper Only 0402, 0603 1505, 1805, 1808 1812, 1825 2220, 2225 Qty. per Reel/7" Reel 2,000 or 4,000 (1) 3,000 1,000 Qty. per Reel/13" Reel 10,000 10,000 4,000 Dependent on chip thickness. Low profile chips shown on page 27 are 5,000 per reel for 7" reel. 0402 size chips are 10,000 per 7" reels and are not available on 13" reels. For 3640 size chip contact factory for quantity per reel. REEL DIMENSIONS Tape Size(1) A Max. B* Min. C D* Min. N Min. 8mm 330 (12.992) 1.5 (.059) 13.0±0.20 (.512±.008) 20.2 (.795) W2 Max. W3 8.4 +1.0 –0.0 (.331 +.060 –0.0 ) 14.4 (.567) 7.9 Min. (.311) 10.9 Max. (.429) 12.4 +2.0 –0.0 +.076 ) (.488 –0.0 18.4 (.724) 11.9 Min. (.469) 15.4 Max. (.607) 50 (1.969) 12mm Metric dimensions will govern. English measurements rounded and for reference only. (1) For tape sizes 16mm and 24mm (used with chip size 3640) consult EIA RS-481 latest revision. 32 W1 Embossed Carrier Configuration 8 & 12mm Tape Only 8 & 12mm Embossed Tape Metric Dimensions Will Govern CONSTANT DIMENSIONS Tape Size 8mm and 12mm D0 +0.10 -0.0 +.004 -0.0 8.4 (.059 E ) P0 P2 1.75 ± 0.10 4.0 ± 0.10 2.0 ± 0.05 (.069 ± .004) (.157 ± .004) (.079 ± .002) T Max. T1 G1 G2 0.600 (.024) 0.10 (.004) Max. 0.75 (.030) Min. See Note 3 0.75 (.030) Min. See Note 4 R Min. See Note 2 T2 W A0 B0 K0 VARIABLE DIMENSIONS Tape Size B1 D1 Max. Min. See Note 6 See Note 5 F P1 8mm 4.55 (.179) 1.0 (.039) 3.5 ± 0.05 4.0 ± 0.10 (.138 ± .002) (.157 ± .004) 25 (.984) 2.5 Max (.098) 8.0 +0.3 -0.1 (.315 +.012 -.004 ) See Note 1 12mm 8.2 (.323) 1.5 (.059) 5.5 ± 0.05 4.0 ± 0.10 (.217 ± .002) (.157 ± .004) 30 (1.181) 6.5 Max. (.256) 12.0 ± .30 (.472 ± .012) See Note 1 8mm 1/2 Pitch 4.55 (.179) 1.0 (.039) 3.5 ± 0.05 2.0 ± 0.10 (.138 ± .002) 0.79 ± .004 25 (.984) 2.5 Max. (.098) 8.0 +0.3 -0.1 (.315 +.012 -.004 ) See Note 1 12mm Double Pitch 8.2 (.323) 1.5 (.059) 5.5 ± 0.05 8.0 ± 0.10 (.217 ± .002) (.315 ± .004) 30 (1.181) 6.5 Max. (.256) 12.0 ± .30 (.472 ± .012) See Note 1 NOTES: 1. A0, B0, and K0 are determined by the max. dimensions to the ends of the terminals extending from the component body and/or the body dimensions of the component. The clearance between the end of the terminals or body of the component to the sides and depth of the cavity (A0, B0, and K0) must be within 0.05 mm (.002) min. and 0.50 mm (.020) max. The clearance allowed must also prevent rotation of the component within the cavity of not more than 20 degrees (see sketches C & D). 2. Tape with components shall pass around radius “R” without damage. The minimum trailer length (Note 2 Fig. 3) may require additional length to provide R min. for 12 mm embossed tape for reels with hub diameters approaching N min. (Table 4). 3. G1 dimension is the flat area from the edge of the sprocket hole to either the outward deformation of the carrier tape between the embossed cavities or to the edge of the cavity whichever is less. 4. G2 dimension is the flat area from the edge of the carrier tape opposite the sprocket holes to either the outward deformation of the carrier tape between the embossed cavity or to the edge of the cavity whichever is less. 5. The embossment hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of embossment location and hole location shall be applied independent of each other. 6. B1 dimension is a reference dimension for tape feeder clearance only. 33 Paper Carrier Configuration 8 & 12mm Tape Only 8 & 12mm Paper Tape Metric Dimensions Will Govern CONSTANT DIMENSIONS Tape Size 8mm and 12mm D0 1.5 (.059 +0.1 -0.0 +.004 -.000 E ) 1.75 ± 0.10 (.069 ± .004) P0 P2 4.0 ± 0.10 2.0 ± 0.05 (.157 ± .004) (.079 ± .002) T1 G1 G2 R MIN. 0.10 (.004) Max. 0.75 (.030) Min. 0.75 (.030) Min. 25 (.984) See Note 2 VARIABLE DIMENSIONS Tape Size P1 F W A0 B0 T 8mm 4.0 ± 0.10 (.157 ± .004) 3.5 ± 0.05 (.138 ± .002) 8.0 +0.3 -0.1 (.315 +.012 -.004 ) See Note 1 See Note 3 12mm 4.0 ± .010 (.157 ± .004) 5.5 ± 0.05 (.217 ± .002) 12.0 ± 0.3 (.472 ± .012) 8mm 1/2 Pitch 2.0 ± 0.10 (.079 ± .004) 3.5 ± 0.05 (.138 ± .002) 8.0 +0.3 -0.1 (.315 +.012 -.004 ) 12mm Double Pitch 8.0 ± 0.10 (.315 ± .004) 5.5 ± 0.05 (.217 ± .002) 12.0 ± 0.3 (.472 ± .012) NOTES: 1. A0, B0, and T are determined by the max. dimensions to the ends of the terminals extending from the component body and/or the body dimensions of the component. The clearance between the ends of the terminals or body of the component to the sides and depth of the cavity (A0, B0, and T) must be within 0.05 mm (.002) min. and 0.50 mm (.020) max. The clearance allowed must also prevent rotation of the component within the cavity of not more than 20 degrees (see sketches A & B). 2. Tape with components shall pass around radius “R” without damage. 3. 1.1 mm (.043) Base Tape and 1.6 mm (.063) Max. for Non-Paper Base Compositions. Bar Code Labeling Standard AVX bar code labeling is available and follows latest version of EIA-556-A. 34 Bulk Case Packaging BENEFITS BULK FEEDER • Easier handling • Smaller packaging volume (1/20 of T/R packaging) • Easier inventory control Case • Flexibility • Recyclable Cassette Gate Shooter CASE DIMENSIONS Shutter Slider 12mm 36mm Mounter Head Expanded Drawing 110mm Chips Attachment Base CASE QUANTITIES Part Size 0402 0603 0805 Qty. (pcs / cassette) 80,000 15,000 10,000 (T=0.6mm) 5,000 (T¯≥0.6mm) 35