J-Type Medallion 6000 1550 nm Externally Modulated Transmitter DATASHEET | JULY 2012 FIBER OPTICS The J-Type Medallion 6000 Series Applications High Performance Supertrunking Links High Power Distribution Networks Redundant Ring Architectures FTTx Networks RFOG Applications This product line is a family of state-of-the-art high performance 1550 nm externally modulated CATV fiber optic transmitters optimized for varying network applications. Packaged in convenient 1RU housing, this line of optical transmitters couples high optical output powers, up to 10.0 dBm, with low optical line width resulting in unmatched performance. The optical modulator, combined with proprietary pre-distortion circuitry, provides superior CTB and CSO performance with SBS suppression levels of greater than 17 dBm for SAT-IF applications. Advanced features such as built in field adjustable SBS control allow these transmitters to be quickly optimized in the field for any link or application without the need to procure specifically tuned transmitters. This affords the system designer a level of flexibility previously unknown in the CATV market place. SAT-IF Transport The J-Type series are designed as a high performance solution for applications where the simultaneous transport of CATV and SAT-IF FM signals is required. The SAT-IF signals can be applied anywhere in the 950 to 2800 MHz band. DWDM Node Splitting Features Single or Dual Optical Outputs QAM Loading to 1003 MHz J-Type transmitters are specially designed and optimized to support optical fiber links of up to 150kms for the Japanese market place. Dual Power Supplies, Redundant & Hot Swappable . Front Panel RF Test Point Vacuum Fluorescent Status Display OMI / RF Gain Adjustment AGC Select: CW, Video, Manual (No AGC) Industry Leading Field Adjustable SBS Suppression | REV 2012.07 Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice. J-Type Medallion 6000 1550 nm Externally Modulated Transmitter FIBER OPTICS DATASHEET | JULY 2012 Optical Characteristics Property Performance (note 1-8) Specified Link Length Units L (km) Channel Plan Models 6000-J01 6000-J02 25 25 NTSC 80-Ch PAL 60-Ch Optical Output Power Po (dBm) 8.5/8.5 8.5/8.5 Noise Bandwidth BW (MHz) 4 5 SBS Suppression (dBm) 15.0 15.0 Comments With 36 QPSK carriers from 950 to 2800 MHz Min. 10 dBm version avail. See Chart Min. CATV Carrier to Noise Ratio CNR (dB) 51.0 51.0 Min. CATV Composite Second Order CSO (dBc) -65 -65 Max. Port 1 CATV Composite Triple Beat CTB (dBc) -65 -65 Max. @ +25C CATV Composite Triple Beat CTB (dBc) -64 -64 Max. @ 0 C to 50 C SAT-IF Carrier to Noise Ratio CNR (dB) 27 27 Min. SAT-IF Intermodulation Products (dBc) -35 -35 Max. Port 1 SAT-IF Spurious Products (dBc) -38 -38 Max. o o Notes: 1. Unless stated otherwise all specifications apply over full temperature range with no digital loading. 2. Unless stated otherwise specifications apply for nominal RF input level as defined below, after a 30 minute stabilization period. 3. Specifications separated by a slash are port1 / port 2. 4. Units are tested per the Test / Link Configuration Table 5. Noise figure for the EDFA = 4.5 ~ 5.5 dB 6. Corning SMF-28 single mode fiber 7. Receiver responsivity is 0.95 mA/mW, Equivalent noise current is 7 pA/(Hz)1/2 8. With 36 QPSK modulated SAT-IF signals between 950 … 2800 MHz. 27 MHz IF bandwidth Test/Link Configuration Property J-Type EDFA 14 dBm Link 25 Km Received Power2 0.0 dBm at the receiver | REV 2012.07 Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice. J-Type Medallion 6000 1550 nm Externally Modulated Transmitter FIBER OPTICS DATASHEET | JULY 2012 Electrical Specifications Property Requirement Comments CATV Nominal Input Power 19 dBmV/ch (79 dBuV/ch) 80 NTSC channels CATV Input Range 17 – 27 dBmV/ch (77 – 87 dBuV/ch) Optimum performance at nominal input CATV Composite Level -10.9 dBm 0 dB on FP Display CATV RF Gain / OMI Adjustment Range +2 / -8 dB from nominal setting CATV Performance may vary slightly over range CATV Frequency Range 45MHz – 1003 MHz CATV Flatness +/- 0.50 dB +/- 0.75 dB 45MHz – 1003 MHz CATV Flatness – N-Type +/- 0.75 dB 45MHz – 1003 MHz N-Type CATV Input impedance 75 CATV Input Return Loss 16dB min CATV Front Panel RF Tap -20 +/- 1 dB down from RF input 45MHz - 550MHz 45MHz – 1003 MHz CATV Front Panel RF Tap Flatness +/- 1 dB 45MHz – 1003 MHz SAT Nominal Input Power 27 dBmV/ch (87 dBuV/ch) 36 QPSK SAT-IF channels SAT Input Range 22 – 32 dBmV/ch (82 – 92 dBuV/ch) Optimum performance at nominal input SAT Composite Level -6.2 dBm 0 dB on FP Display SAT-IF RF Gain / OMI Adjustment Range +5 / -5 dB from nominal setting CATV Performance can vary slightly SAT-IF Frequency Range 950MHz – 2800 MHz SAT-IF Flatness +/- 2 dB SAT-IF Input impedance 75 SAT-IF Input Return Loss 10dB min SAT-IF Front Panel RF Tap 7 +/- 2.5 dBmV/Ch at Nominal OMI/ch SAT-IF Front Panel RF Tap Flatness +/- 1 dB 950MHz – 2800 MHz 950MHz – 2800 MHz General and Mechanical Specifications Property Requirement Wavelength 1550 +/-5 nm Channel Plan Various – See Specification Tables Optical Connector Monitoring Interfaces SC/APC 100 Base-T Ethernet (SNMP) Rear Panel RS-232 interface VFD Screen Front Panel Controls Operating Temperature 0C to 50C Storage Temperature -20C to 70C 65W max Power Consumption Comments Various Options + ITU-grid available – see Model Number Information Custom channel plans available Other styles available VFD- (Vacuum Fluorescent Display) | REV 2012.07 Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice. J-Type Medallion 6000 1550 nm Externally Modulated Transmitter FIBER OPTICS DATASHEET | JULY 2012 General and Mechanical Specifications (continued) Property Requirement Comments Transportation Vibration EMI: EN50083-2:2006 (US CATV) EN55022:2006 (US IT) EN61000-3-2 (Harmonics) EN61000-3-3 (Flicker) FCC: Part 15, Subpart B, class “A” Unintentional Radiators ICES-003 (Canada) AN/NZS 3548, Class A (Australia) VCCI, Class A (Japan) GR-2853-CORE Transportation Shock GR-2853-CORE In Shipping package 20% to 85% 90 to 265 VAC, 50/60 Hz Non-condensing Agency Listings Operating Humidity Supply Range (VAC) (VDC) Dimensions Safety: FDA/CDRH Laser Safety Governed by Code of Federal Regulations Title 21, Volume 8, Part 1040 IEC 60950-1 IEC 60728-11 Laser IEC 60825-1 CB Certification In Shipping package +/- (36 – 72) VDC 19.0”W x 15.0”D x 1.72”H (width includes 19” front panel ears, depth includes, connectors, fans & front panel) – see drawing Laser Safety Information This product meets the applicable requirements of 21 CFR 1010 & 1040 and is classified as a class 1M laser product. During use as intended, the laser energy is fully contained within the fiber network such that there is no accessible laser radiation. This product has been issued accession number 0820466-001. | REV 2012.07 Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice. J-Type Medallion 6000 1550 nm Externally Modulated Transmitter FIBER OPTICS DATASHEET | JULY 2012 Model Number InformationNote 3 6000 – □□□ □-□ □□□□ Logo & Customer Specific Link type Pout (dBm min) Note 1 Loading Type Optics 0– EMCORE Logo J – 25 km Note 4 D – 10/10 for S and J Type 1 – NTSC (80-ch) 1 – SC/APC, Rear E – 8.5/8.5 for J Type 2 – PAL (60-ch) 2 – FC/APC, Rear 1 – no Logo 3 – E2000/APC, Rear 4 – SC/APC, Front 5 – FC/APC, Front RF 1 – RF IN Rear, TP Front 2 – RF IN Front, TP Front 3 – RF IN Front, TP Rear 4 – RF IN Rear, TP Rear Wavelength (nm) Power Supply 00 –1555+/5.0nm 1 – AC primary, no secondary 01 – 1550+/5.0nm 2 – DC primary, no secondary xx – ITU Channel +/Note 2 0.1nm 3 – AC primary, AC secondary 4 – AC primary, DC secondary 5 – DC primary, DC secondary 6 – E2000/APC, Front Note 1: Options available for Indicated Types only. Note 2: ITU grid wavelengths can be specified from channel 18 to 40. Note 3: Not all configurations are available, contact factory. Note 4: CSO port 2 degraded by 1dB Note 5: Contact Factory for Model type availability Additional Kits G3708-006-001 - Replaceable AC power supply modules G3708-005-001 - Replaceable DC power supply modules G7914-076-001 - Replaceable Blank power module plate G7906-008-001 - Replaceable fans | REV 2012.07 Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice.