54ACT16841, 74ACT16841 20-BIT BUS-INTERFACE D-TYPE LATCHES WITH 3-STATE OUTPUTS SCAS174A – MAY 1991 – REVISED APRIL 1996 D D D D D D D D D Members of the Texas Instruments Widebus Family Inputs Are TTL-Voltage Compatible 3-State Outputs Drive Bus Lines Directly Provide Extra Bus Driving/Latches Necessary for Wider Address/Data Paths or Buses With Parity Flow-Through Architecture Optimizes PCB Layout Distributed VCC and GND Pin Configuration Minimizes High-Speed Switching Noise EPIC (Enhanced-Performance Implanted CMOS) 1-µm Process 500-mA Typical Latch-Up Immunity at 125°C Package Options Include Plastic Thin Shrink Small-Outline (DGG) Packages, 300-mil Shrink Small-Outline (DL) Packages Using 25-mil Center-to-Center Pin Spacings, and 380-mil Fine-Pitch Ceramic Flat (WD) Packages Using 25-mil Center-to-Center Pin Spacings 54ACT16841 . . . WD PACKAGE 74ACT16841 . . . DGG OR DL PACKAGE (TOP VIEW) 1OE 1Q1 1Q2 GND 1Q3 1Q4 VCC 1Q5 1Q6 1Q7 GND 1Q8 1Q9 1Q10 2Q1 2Q2 2Q3 GND 2Q4 2Q5 2Q6 VCC 2Q7 2Q8 GND 2Q9 2Q10 2OE description These 20-bit latches feature 3-state outputs designed specifically for driving highly capacitive or relatively low-impedance loads. They are particularly suitable for implementing buffer registers, I/O ports, bidirectional bus drivers, and working registers. 1 56 2 55 3 54 4 53 5 52 6 51 7 50 8 49 9 48 10 47 11 46 12 45 13 44 14 43 15 42 16 41 17 40 18 39 19 38 20 37 21 36 22 35 23 34 24 33 25 32 26 31 27 30 28 29 1LE 1D1 1D2 GND 1D3 1D4 VCC 1D5 1D6 1D7 GND 1D8 1D9 1D10 2D1 2D2 2D3 GND 2D4 2D5 2D6 VCC 2D7 2D8 GND 2D9 2D10 2LE The ’ACT16841 can be used as two 10-bit latches or one 20-bit latch. The 20 latches are transparent D-type. While the latch-enable (1LE or 2LE) input is high, the Q outputs of the corresponding 10-bit latch follow the data (D) inputs. When LE is taken low, the Q outputs are latched at the levels that were set up at the D inputs. A buffered output-enable (1OE or 2OE) input can be used to place the outputs of the corresponding 10-bit latch in either a normal logic state (high or low logic levels) or a high-impedance state. In the high-impedance state, the outputs neither load nor drive the bus lines significantly. OE does not affect the internal operation of the latches. Old data can be retained or new data can be entered while the outputs are in the high-impedance state. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. EPIC and Widebus are trademarks of Texas Instruments Incorporated. Copyright 1996, Texas Instruments Incorporated UNLESS OTHERWISE NOTED this document contains PRODUCTION DATA information current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 54ACT16841, 74ACT16841 20-BIT BUS-INTERFACE D-TYPE LATCHES WITH 3-STATE OUTPUTS SCAS174A – MAY 1991 – REVISED APRIL 1996 description (continued) The 74ACT16841 is packaged in TI’s shrink small-outline package (DL), which provides twice the I/O pin count and functionality of standard small-outline packages in the same printed-circuit-board area. The 54ACT16841 is characterized for operation over the full military temperature range of –55°C to 125°C. The 74ACT16841 is characterized for operation from –40°C to 85°C. FUNCTION TABLE (each 10-bit latch) INPUTS OE LE D OUTPUT Q L H H H L H L L L L X Q0 H X X Z logic symbol† 1 1OE 1LE 56 28 2OE 2LE 1D1 1D2 1D3 1D4 1D5 1D6 1D7 1D8 1D9 1D10 2D1 2D2 2D3 2D4 2D5 2D6 2D7 2D8 2D9 2D10 29 55 EN2 C1 EN4 C3 1D 54 2 2 52 5 51 6 49 8 48 9 47 10 45 12 44 13 43 14 42 3D 41 4 15 16 40 17 38 19 37 20 36 21 34 23 33 24 31 26 30 27 † This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12. 2 3 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1Q1 1Q2 1Q3 1Q4 1Q5 1Q6 1Q7 1Q8 1Q9 1Q10 2Q1 2Q2 2Q3 2Q4 2Q5 2Q6 2Q7 2Q8 2Q9 2Q10 54ACT16841, 74ACT16841 20-BIT BUS-INTERFACE D-TYPE LATCHES WITH 3-STATE OUTPUTS SCAS174A – MAY 1991 – REVISED APRIL 1996 logic diagram (positive logic) 1OE 1LE 1 2OE 56 2LE C1 1D1 2 55 28 29 C1 1Q1 2D1 1D 42 15 2Q1 1D To Nine Other Channels To Nine Other Channels absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 7 V Input voltage range, VI (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to VCC + 0.5 V Output voltage range, VO (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to VCC + 0.5 V Input clamp current, IIK (VI < 0 or VI > VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20 mA Output clamp current, IOK (VO < 0 or VO > VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±50 mA Continuous output current, IO (VO = 0 to VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±50 mA Continuous current through VCC or GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±500 mA Maximum package power dissipation at TA = 55°C (in still air) (see Note 2): DGG package . . . . . . . . . . 1 W DL package . . . . . . . . . . . 1.4 W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The input and output voltage ratings may be exceeded if the input and output current ratings are observed. 2. The maximum package power dissipation is calculated using a junction temperature of 150_C and a board trace length of 750 mils. recommended operating conditions (see Note 3) 54ACT16841 NOM MAX MIN NOM MAX 4.5 5 5.5 4.5 5 5.5 VCC VIH Supply voltage VIL VI Low-level input voltage Input voltage 0 VO IOH Output voltage 0 High-level output current IOL ∆t/∆v Low-level output current High-level input voltage 74ACT16841 MIN 2 2 0.8 Input transition rise or fall rate TA Operating free-air temperature NOTE 3: Unused inputs must be held high or low to prevent them from floating. UNIT V V 0.8 V VCC VCC V –24 –24 mA 24 24 mA VCC VCC 0 0 V 0 10 0 10 ns/V –55 125 –40 85 °C PRODUCT PREVIEW information concerns products in the formative or design phase of development. Characteristic data and other specifications are design goals. Texas Instruments reserves the right to change or discontinue these products without notice. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3 54ACT16841, 74ACT16841 20-BIT BUS-INTERFACE D-TYPE LATCHES WITH 3-STATE OUTPUTS SCAS174A – MAY 1991 – REVISED APRIL 1996 electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER TEST CONDITIONS VCC 4.5 V IOH = –50 50 µA VOH 24 mA IOH = –24 IOH = –75 mA† II IOZ ICC IOL = 75 mA† VI = VCC or GND 54ACT16841 MIN ∆ICC‡ One input at 3.4 V, Other inputs at VCC or GND Ci VI = VCC or GND VO = VCC or GND 74ACT16841 MIN 4.4 4.4 5.5 V 5.4 5.4 5.4 4.5 V 3.94 3.8 3.8 5.5 V 4.94 4.8 4.8 3.85 3.85 0.1 0.1 MAX UNIT V 0.1 5.5 V 0.1 0.1 0.1 4.5 V 0.36 0.44 0.44 5.5 V 0.36 0.44 0.44 1.65 1.65 ±1 ±1 µA 5.5 V IO = 0 MAX 4.4 4.5 V IOL = 24 mA VO = VCC or GND VI = VCC or GND, TA = 25°C TYP MAX 5.5 V IOL = 50 µA VOL MIN V 5.5 V ±0.1 5.5 V ±0.5 ±5 ±5 µA 5.5 V 8 80 80 µA 5.5 V 0.9 1 1 mA 5V 3 pF Co 5V 11 † Not more than one output should be tested at a time, and the duration of the test should not exceed 10 ms. ‡ This is the increase in supply current for each input that is at one of the specified TTL voltage levels rather than 0 V or VCC. pF timing requirements over recommended operating free-air temperature range, VCC = 5 V ± 0.5 V (unless otherwise noted) (see Figure 1) TA = 25°C MIN MAX tw tsu th Pulse duration, LE high Setup time, data before LE↓ Hold time, time data after LE↓ 54ACT16841 MIN MAX 74ACT16841 MIN MAX UNIT 4 4 4 ns ns 1.5 1.5 1.5 High 3 3 3 Low 4.5 4.5 4.5 ns switching characteristics over recommended operating free-air temperature range, VCC = 5 V ± 0.5 V (unless otherwise noted) (see Figure 1) PARAMETER FROM (INPUT) TO (OUTPUT) tPLH tPHL D Q tPLH tPHL LE Q tPZH tPZL OE Q tPHZ tPLZ OE Q TA = 25°C MIN TYP MAX POST OFFICE BOX 655303 74ACT16841 MIN MAX MIN MAX 4 7.1 10.3 4 11.8 4 11.8 3.2 6.9 11 3.2 12.2 3.2 12.2 4.5 7.7 11.3 4.5 12.7 4.5 12.7 4.3 7.8 11.4 4.3 12.7 4.3 12.7 3.1 6.4 10.1 3.1 11.3 3.1 11.3 3.8 7.6 12.1 3.8 13.7 3.8 13.7 4 7.3 9.5 4 10.2 4 10.2 4 6.8 8.9 4 9.6 4 9.6 PRODUCT PREVIEW information concerns products in the formative or design phase of development. Characteristic data and other specifications are design goals. Texas Instruments reserves the right to change or discontinue these products without notice. 4 54ACT16841 • DALLAS, TEXAS 75265 UNIT ns ns ns ns 54ACT16841, 74ACT16841 20-BIT BUS-INTERFACE D-TYPE LATCHES WITH 3-STATE OUTPUTS SCAS174A – MAY 1991 – REVISED APRIL 1996 operating characteristics, VCC = 5 V, TA = 25°C PARAMETER Cpd d TEST CONDITIONS Outputs enabled Power dissipation capacitance pF CL = 50 pF, Outputs disabled TYP f = 1 MHz 41 10 UNIT pF PARAMETER MEASUREMENT INFORMATION 2 × VCC S1 500 Ω From Output Under Test Open GND TEST S1 tPLH/tPHL tPLZ/tPZL tPHZ/tPZH Open 2 × VCC GND 500 Ω CL = 50 pF (see Note A) LOAD CIRCUIT 3V Timing Input (see Note B) 1.5 V 0V tw tsu 3V Input 1.5 V th 1.5 V 3V 1.5 V 1.5 V Data Input 0V 0V VOLTAGE WAVEFORMS VOLTAGE WAVEFORMS Output Control (low-level enabling) 3V 1.5 V Input 1.5 V 0V tPHL tPLH In-Phase Output 50% VCC 50% VCC 0V tPZL VOH 50% VCC VOL Output Waveform 2 S1 at GND (see Note B) [ VCC tPLZ Output Waveform 1 S1 at 2 × VCC (see Note B) tPLH tPHL Out-of-Phase Output VOH 50% VCC VOL 3V 1.5 V 1.5 V 50% VCC VOL tPHZ tPZH VOLTAGE WAVEFORMS 20% VCC 50% VCC 80% VCC VOH [0V VOLTAGE WAVEFORMS NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 1 MHz, ZO = 50 Ω, tr = 3 ns, tf = 3 ns. D. The outputs are measured one at a time with one input transition per measurement. Figure 1. Load Circuit and Voltage Waveforms POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 5 PACKAGE OPTION ADDENDUM www.ti.com 18-Jul-2006 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty 74ACT16841DGGR OBSOLETE TSSOP DGG 56 74ACT16841DL ACTIVE SSOP DL 56 74ACT16841DLG4 ACTIVE SSOP DL 56 74ACT16841DLR ACTIVE SSOP DL 74ACT16841DLRG4 ACTIVE SSOP DL Lead/Ball Finish MSL Peak Temp (3) Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 20 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 20 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 56 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 56 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 11-Mar-2008 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel Diameter Width (mm) W1 (mm) A0 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 74ACT16841DGGR TSSOP DGG 56 0 330.0 24.4 8.6 15.6 1.8 12.0 24.0 Q1 74ACT16841DLR SSOP DL 56 1000 330.0 32.4 11.35 18.67 3.1 16.0 32.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 11-Mar-2008 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) 74ACT16841DGGR TSSOP DGG 74ACT16841DLR SSOP DL 56 0 346.0 346.0 41.0 56 1000 346.0 346.0 49.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Amplifiers Data Converters DSP Clocks and Timers Interface Logic Power Mgmt Microcontrollers RFID RF/IF and ZigBee® Solutions amplifier.ti.com dataconverter.ti.com dsp.ti.com www.ti.com/clocks interface.ti.com logic.ti.com power.ti.com microcontroller.ti.com www.ti-rfid.com www.ti.com/lprf Applications Audio Automotive Broadband Digital Control Medical Military Optical Networking Security Telephony Video & Imaging Wireless www.ti.com/audio www.ti.com/automotive www.ti.com/broadband www.ti.com/digitalcontrol www.ti.com/medical www.ti.com/military www.ti.com/opticalnetwork www.ti.com/security www.ti.com/telephony www.ti.com/video www.ti.com/wireless Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2008, Texas Instruments Incorporated