766 Series Pulse Transformers Up to 50 Vμs ET Industry standard pinout 500VDC Isolation PCB mounting UL 94 V-0 package materials μH pF Ω Vrms 1916 492 219 50 1916 492 219 9.5 20.1 938 11.7mH 2060 3200 4350 17.5 8.5 5.5 4.0 17.5 8.5 5.5 6 2.5 10.5 50.5 17.5 45 23 0.60 0.30 0.25 0.20 0.60 0.30 0.25 0.20 0.20 0.20 0.40 0.60 2.00 3.00 49 22 14 10 49 22 12 13 5 35 250 72 52 35 1.50 0.80 0.50 0.40 1.50 0.80 0.50 0.40 0.20 0.15 1.35 1.50 1.00 1.00 A 1 500 B C D 2 Please note: For additional variants please see 786 series datasheet. Toroidal construction ABSOLUTE MAXIMUM RATINGS Fully encapsulated Operating free air temperature range 0°C to 70°C Storage temperature range -60°C to 125°C DESCRIPTION SOLDERING INFORMATION1 The 766 Series is a range of general purpose pulse transformers. Common applications include line coupling, impedance-matching, or isolating. The devices can also be used in small isolated power supplies or as common-mode chokes in filtering applications. Mechcanical Dimensions Vμs 1:1 1:1 1:1 1:1 1:1 1:1 1:1 1:1 1:1 1:1 1:1 1:1:1 1CT:1CT 2CT:1CT Pin Connection Style μH 76600/1C 76600/2C 76600/3C 76600/4C 76601/1C 76601/2C 76601/3C 76601/6C 76601/20C 76601/23C 76601/24C 76602/1C 76615/1C 76616/3C Min. Primary Constant, ET Max. Isolation Voltage Inductance to 11.7mH Max. DC Resistance 4 Configurations Max. Interwinding Capacitance RoHS compliant Turns Ratio ±2% Max. Leakage Inductance FEATURES Order Code Min. Primary Inductance SELECTION GUIDE1 Peak wave solder temperature 300˚C for 10 seconds Pin finish Matte tin with nickel pre-plate 1 For further information, please visit www.murata-ps.com/rohs All specifications typical at TA=25°C. For full details go to www.murata-ps.com/rohs www.murata-ps.com Technical enquiries - email: [email protected], tel: +44 (0)1908 615232 KMP_766C_B02 Page 1 of 3 766 Series Pulse Transformers PACKAGE SPECIFICATIONS MECHANICAL DIMENSIONS 1 2 1 5 12.70 (0.500) Max. 8.89 (0.350) Max. 8.89 (0.350) Max. 12.70 (0.500) Max. 2 610 6C 6 1 3 5 6.35 (0.250) 2.54 (0.100) 10.16 (0.400) 0.56±0.05 (0.022±0.002) 2.54 (0.100) 2.54 (0.100) 5.08 (0.200) 0.56±0.05 (0.022±0.002) 10.00 (0.394) 5.84 (0.230) XYYWW 6.35 (0.250) 10.00 (0.394) 5.84 (0.230) XYYWW 602 1C 2 4 6 10.16 (0.400) Unless otherwise stated all dimensions in mm (inches) ±0.25 (0.01). All pins on a 2.54 (0.1) pitch and within ±0.25 (0.01) of true position. Package Weight: 1.1g Typ. RECOMMENDED FOOTPRINT DETAILS TUBE DIMENSIONS 15.25 (0.60) 21.25 (0.84) 11.00+0.5-0.0 (0.433+0.02-0.0) Y)0-&4 Holes may be omitted for variants with fewer than 6 pins. Unless otherwise stated all dimensions in mm (inches) ±0.25 (0.01). All pins on a 2.54 (0.1) pitch and within ±0.25 (0.01) of true position. www.murata-ps.com 6.9+0.5-0.0 (0.272+0.02-0.0) 0.50±0.15 (0.020±0.006) Tube length: 520±2.0 (20.47±0.08) Unless otherwise stated all dimensions in mm (inches) ±0.55 (0.022). Technical enquiries - email: [email protected], tel: +44 (0)1908 615232 KMP_766C_B02 Page 2 of 3 766 Series Pulse Transformers PACKAGE SPECIFICATIONS (continued) PIN CONNECTION STYLE - 6 PIN DIP (TOP VIEW) " # 13* $ 13* 4&$ 4&$ % 13* 4&$ 4&$ 13* 4&$ TECHNICAL NOTES ISOLATION VOLTAGE REPEATED HIGH-VOLTAGE ISOLATION TESTING ‘Hi Pot Test’, ‘Flash Tested’, ‘Withstand Voltage’, ‘Proof Voltage’, ‘Dielectric Withstand Voltage’ & ‘Isolation Test Voltage’ are all terms that relate to the same thing, a test voltage, applied for a specified time, across a component designed to provide electrical isolation, to verify the integrity of that isolation. It is well known that repeated high-voltage isolation testing of a barrier component can actually degrade isolation capability, to a lesser or greater degree depending on materials, construction and environment. This series has toroidal isolation transformers, with no additional insulation between primary and secondary windings of enameled wire. While parts can be expected to withstand several times the stated test voltage, the isolation capability does depend on the wire insulation. Any material, including this enamel (typically polyurethane) is susceptible to eventual chemical degradation when subject to very high applied voltages thus implying that the number of tests should be strictly limited. We therefore strongly advise against repeated high voltage isolation testing, but if it is absolutely required, that the voltage be reduced by 20% from specified test voltage. All products in this series are 100% production tested at their stated isolation voltage. A question commonly asked is, “What is the continuous voltage that can be applied across the part in normal operation?” For a part holding no specific agency approvals both input and output should normally be maintained within SELV limits i.e. less than 42.4V peak, or 60VDC. The isolation test voltage represents a measure of immunity to transient voltages and the part should never be used as an element of a safety isolation system. The part could be expected to function correctly with several hundred volts offset applied continuously across the isolation barrier; but then the circuitry on both sides of the barrier must be regarded as operating at an unsafe voltage and further isolation/insulation systems must form a barrier between these circuits and any user-accessible circuitry according to safety standard requirements. This consideration equally applies to agency recognized parts rated for better than functional isolation where the wire enamel insulation is always supplemented by a further insulation system of physical spacing or barriers. USA: Mansfield (MA), Tel: (800) 233 2765, email: [email protected] Canada: Toronto, Tel: (866) 740 1232, email: [email protected] Murata Power Solutions, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1151 U.S.A. Tel: (508) 339-3000 (800) 233-2765 Fax: (508) 339-6356 www.murata-ps.com email: [email protected] ISO 9001 REGISTERED Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change without notice. © 2008 Murata Power Solutions, Inc. www.murata-ps.com UK: Milton Keynes, Tel: +44 (0)1908 615232, email: [email protected] France: Montigny Le Bretonneux, Tel: +33 (0)1 34 60 01 01, email: [email protected] Germany: München, Tel: +49 (0)89-544334-0, email: [email protected] Japan: Tokyo, Tel: 3-3779-1031, email: [email protected] Osaka, Tel: 6-6354-2025, email: [email protected] Website: www.murata-ps.jp China: Shanghai, Tel: +86 215 027 3678, email: [email protected] Guangzhou, Tel: +86 208 221 8066, email: [email protected] Technical enquiries - email: [email protected], tel: +44 (0)1908 615232 KMP_766C_B02 Page 3 of 3