AAT4680 Electronic Resettable Fuse General Description Features The AAT4680 electronic resettable fuse is a member of AnalogicTech’s Application Specific Power MOSFET™ (ASPM™) product family. It is a 1A current limited P-channel MOSFET power device that remains fully enhanced as long as the input power supply is above an under-voltage lockout threshold and the load is below the current limit setting. If the load increases above the current limit setting, as is the case during a short circuit, the MOSFET effectively becomes a constant current source equal to the current limit. If the current limit condition persists long enough to heat the MOSFET to an extreme temperature, the device will thermal cycle off and on until the current limit condition is removed. An open drain FAULT flag signals an over-current or over-temperature condition. Quiescent current is typically a low 10µA. • • • • • • • • • • SmartSwitch™ 500mA Steady State Load Current 600mA Minimum Current Limit Trip Point Low Quiescent Current: Typically 10µA Over-Temperature Protection Fast Transient Tesponse: — <1µs Response to Short Circuit 400mΩ Typical RDS(ON) Under-Voltage Lockout FAULT Flag with 3ms Blanking 5-Pin SOT23 Package Temperature Range: -40°C to +85°C Applications • • • • The AAT4680 is available in a Pb-free, 5-pin SOT23 package and is specified over the -40°C to +85°C temperature range. Cell Phone Ports Desktop PCs Peripheral Ports USB Ports Typical Application 5 INPUT OUT IN OUT AAT4680 FAULT CIN 1μF GND 4680.2006.05.1.2 1 GND 2 3 FAULT COUT 1μF GND 1 AAT4680 Electronic Resettable Fuse Pin Descriptions Pin # Symbol Function 1 OUT P-channel MOSFET drain. 2 GND Ground connection. 3 FAULT 4 N/C 5 IN Open drain output; signals over-current and over-temperature condition. Not internally connected. P-channel MOSFET source. Pin Configuration SOT23-5 2 OUT 1 GND 2 FAULT 3 5 IN 4 N/C 4680.2006.05.1.2 AAT4680 Electronic Resettable Fuse Absolute Maximum Ratings1 TA = 25°C, unless otherwise noted. Symbol VIN VOUT VFLG IOUT TJ VESD TLEAD Description IN to GND OUT to GND FAULT to GND Output Current Operating Junction Temperature Range ESD Rating2 - HBM Maximum Soldering Temperature (at Leads) Value Units -0.3 to 6 -0.3 to 6 -0.3 to 6 Internally Limited -40 to 150 5000 300 V V V A °C V °C Value Units 150 667 °C/W mW Thermal Characteristics3 Symbol ΘJA PD Description Maximum Thermal Resistance Maximum Power Dissipation 1.Stresses above those listed in Absolute Maximum Ratings may cause permanent damage to the device. Functional operation at conditions other than the operating conditions specified is not implied. Only one Absolute Maximum Rating should be applied at any one time. 2. Human body model is a 100pF capacitor discharged through a 1.5kΩ resistor into each pin. 3. Mounted on a demo board. 4680.2006.05.1.2 3 AAT4680 Electronic Resettable Fuse Electrical Characteristics VIN = 5V, TA = -40°C to +85°C, unless otherwise noted. Typical values are at TA = 25°C; bold values designate full temperature range. Symbol VIN IQ VUVLO VUVLO(HYS) RDS(ON) ILIM tRESP VFAULTLOW ISINK Tblank TSD 4 Description Operation Voltage Quiescent Current Under-Voltage Lockout Under-Voltage Lockout Hysteresis On Resistance Current Limit Current Loop Response FAULT Logic Output Low FAULT Logic Output High Leakage Current FAULT Blanking Time Over-Temperature Threshold Conditions Min Typ 1.8 VIN = 5V, IOUT = 0 VIN Falling VIN = 5.0V, TA = 25°C VIN = 3.V, TA = 25°C OUT < IN - 0.5V VIN = 5V ISINK = 1mA VFAULT = 5.5V 0.6 10 1.5 0.3 400 525 0.875 500 0.5 3 125 Max Units 5.5 20 1.8 V µA V V 500 650 1.25 mΩ 0.4 A ns V 1 µA ms °C 4680.2006.05.1.2 AAT4680 Electronic Resettable Fuse Typical Characteristics Unless otherwise noted, VIN = 5V, TA = 25°C. Quiescent Current vs. Input Voltage Quiescent Current vs. Temperature 12 18 Quiescent Current (μA) Quiescent Current (μA) 20 16 14 12 10 8 6 4 2 0 -40 10 8 6 4 2 0 -20 0 20 40 60 80 100 120 0 1 2 Temperature (°C) 3 4 5 6 Input Voltage (V) RDS(ON) vs. Temperature Current Limit vs. Output Voltage 700 1 RDS(ON) (mΩ) Output Current (A) 650 0.8 0.6 0.4 0.2 600 VIN = 3V 550 500 450 VIN = 5V 400 350 0 0 1 2 3 4 5 300 -40 -20 0 Output Voltage (V) 3 Output Voltage 0 1 Output Current -1 1.0 Time (μs) 4680.2006.05.1.2 1.5 2.0 Input and Output Voltage (V) 5 2 0.5 80 100 120 6 5 Input Voltage 4 3 Output Current 2 1 Output Voltage 0 -0.5 Output Current (A) Input Voltage Output Current (A) Input and Output Voltage (V) 7 0.0 60 Short Circuit Through 0.6Ω 6 -2 -0.5 40 Temperature (°C) Short Circuit Through 0.3Ω 4 20 -1 0.0 0.5 1.0 1.5 2.0 Time (μs) 5 AAT4680 Electronic Resettable Fuse Typical Characteristics Unless otherwise noted, VIN = 5V, TA = 25°C. Thermal Shutdown Response FAULT (5V/div) Fault Delay FAULT (5V/div) VOUT (2V/div) VOUT (2V/div) IIN (500mA/div) Time (50ms/div) 6 IIN (500mA/div) Time (2ms/div) 4680.2006.05.1.2 AAT4680 Electronic Resettable Fuse Functional Block Diagram IN OUT Under-Voltage Lockout Over-Temperature Protection Current Limit FAULT 3ms Blanking GND Functional Description The AAT4680 is a single channel electronic resettable fuse that protects against short-circuit conditions by current limiting to a preset level. A patented fast acting current limit loop limits load current in a fraction of a microsecond and instantly resets to low impedance once the short-circuit condition is removed. A current limit condition is reported by the open drain FAULT output after a three millisecond blanking interval. The blanking prevents false reporting during the charging of a capacitive load, which typically occurs when a load is connected. The AAT4680 is internally protected from thermal damage by an over-temperature detection circuit. If the die temperature reaches the internal thermal 4680.2006.05.1.2 limit, the power device is switched off until the die temperature cools to a level below the thermal limit threshold. The device will thermal cycle indefinitely until the over-current condition is removed. The AAT4680 operates with input voltages ranging from 1.8V to 5.5V which, along with extremely low operating current, makes it ideal for battery-powered applications. In cases where the input voltage drops below 1.8V, the AAT4680 internal MOSFET is protected from entering the saturated region of operation by being automatically shut down by an under-voltage lockout circuit. The AAT4680 is ideally suited for protection of peripheral ports such as USB, RS232, and parallel ports. 7 AAT4680 Electronic Resettable Fuse Applications Information Input Capacitor The input capacitor, CIN, protects the power supply from current transients generated by the load attached to the AAT4680. If a short circuit is suddenly applied to the output of the AAT4680, there is a 500 nanosecond long period during which a large current can flow before current limit circuitry activates. (See characteristic curve "Short Circuit Through 0.3Ω.") In this event, a properly sized input capacitor can dramatically reduce the voltage transient seen by the power supply and other circuitry upstream from the AAT4680. CIN should be located as close to the device VIN pin as practically possible. Ceramic, tantalum, or aluminum electrolytic capacitors may be selected for CIN. There is no specific capacitor equivalent series resistance (ESR) requirement for CIN. However, for higher current operation, ceramic capacitors are recommended for CIN due to their inherent capability over tantalum capacitors to withstand input current surges from low impedance sources such as batteries in portable devices. ture circuits in any combination are active for more than approximately three milliseconds, FAULT is pulled to ground through approximately 100Ω. Removal of voltage or current transients of less than two milliseconds prevents capacitive loads connected to the AAT4680 output from activating the FAULT flag when they are initially attached. Pull-up resistances of 1kΩ to 100kΩ are recommended. Since FAULT is an open drain terminal, it may be pulled up to any voltage rail less than the maximum operating voltage of 5.5V, allowing for level shifting between circuits. Thermal Considerations Since the AAT4680 has internal current limit and over-temperature protection, junction temperature is rarely a concern. However, if the application requires large currents in a hot environment, it is possible that temperature, rather than current limit, will be the dominant regulating condition. In these applications, the maximum current available without risk of an over-temperature condition must be calculated. The maximum internal temperature while current limit is not active can be calculated using Equation 1. Output Capacitor In order to insure stability while current limit is active, a small output capacitance of approximately 1µF is required. No matter how big the output capacitor, output current is limited to the value set by the AAT4680 current limiting circuitry, allowing very large output capacitors to be used. For example, USB ports are specified to have at least 120µF of capacitance downstream from their controlling power switch. The current limiting circuit will allow an output capacitance of 1000µF or more without disturbing the upstream power supply. Eq. 1: TJ(MAX) = IMAX2 · RDS(ON)(MAX) · RΘJA + TA(MAX) In Equation 1, IMAX is the maximum current required by the load. RDS(ON)(MAX) is the maximum rated RDS(ON) of the AAT4680 at high temperature. RθJA is the thermal resistance between the AAT4680 die and the board onto which it is mounted. TA(MAX) is the maximum temperature that the PCB under the AAT4680 would be if the AAT4680 were not dissipating power. Equation 1 can be rearranged to solve for IMAX; Equation 2. Attaching Loads Capacitive loads attached to the AAT4680 will charge at a rate no greater than the current limit setting. FAULT Output A FAULT flag is provided to alert a system if the AAT4680 load is not receiving sufficient voltage to operate properly. If current limit or over-tempera- 8 Eq. 2: IMAX = TSD(MIN) - TA(MAX) RDS(ON)(MAX) · RΘJA TSD(MIN) is the minimum temperature required to activate the AAT4680 over-temperature protection. With typical specification of 125°C, 115°C is a safe minimum value to use. 4680.2006.05.1.2 AAT4680 Electronic Resettable Fuse For example, if an application is specified to operate in 50°C environments, the PCB operates at temperatures as high as 85°C. The application is sealed and its PCB is small, causing RθJA to be approximately 150°C/W. Using Equation 2: Eq. 3: IMAX = 115 - 85 = 575mA 600 · 150 To prevent thermal limiting, the operating load current in the application must be less than 575mA. 4680.2006.05.1.2 9 AAT4680 Electronic Resettable Fuse Ordering Information Package Marking1 Part Number (Tape and Reel)2 SOT23-5 BWXYY AAT4680IGV-T1 All AnalogicTech products are offered in Pb-free packaging. The term “Pb-free” means semiconductor products that are in compliance with current RoHS standards, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. For more information, please visit our website at http://www.analogictech.com/pbfree. Package Information 2.85 ± 0.15 1.90 BSC 0.40 ± 0.10 0.075 ± 0.075 0.15 ± 0.07 4° ± 4° 10° ± 5° 1.10 ± 0.20 0.60 REF 1.20 ± 0.25 2.80 ± 0.20 1.575 ± 0.125 0.95 BSC 0.60 REF 0.45 ± 0.15 GAUGE PLANE 0.10 BSC All dimensions in millimeters. 1. XYY = assembly and date code. 2. Sample stock is generally held on all part numbers listed in BOLD. © Advanced Analogic Technologies, Inc. AnalogicTech cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in an AnalogicTech product. No circuit patent licenses, copyrights, mask work rights, or other intellectual property rights are implied. AnalogicTech reserves the right to make changes to their products or specifications or to discontinue any product or service without notice. Customers are advised to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability. AnalogicTech warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with AnalogicTech’s standard warranty. Testing and other quality control techniques are utilized to the extent AnalogicTech deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed. AnalogicTech and the AnalogicTech logo are trademarks of Advanced Analogic Technologies Incorporated. All other brand and product names appearing in this document are registered trademarks or trademarks of their respective holders. Advanced Analogic Technologies, Inc. 830 E. Arques Avenue, Sunnyvale, CA 94085 Phone (408) 737-4600 Fax (408) 737-4611 10 4680.2006.05.1.2