ACE701D PFM STEP-UP DC/DC Converter with High Efficiency and Low Noise Description The ACE701D series are CMOS-based PFM step-up DC-DC Converter. The converter can start up by supply voltage as low as 0.8V, and capable of delivering maximum 200mA output current at 3.3V output with 1.8V input Voltage. Quiescent current drawn from power source is as low as 5.5uA. All of these features make ACE701D series be suitable for the portable devices, which are supplied by a single battery to four-cell batteries. To reduce the noise caused by the switch regulator, ACE701D is well considerate in circuit design and manufacture. So that the interferer to other circuits by the device is reduced greatly. ACE701D integrates stable reference circuits and trimming technology, so it can afford high precision and low temperature-drift coefficient of the output voltage. Features Deliver 200mA at 3.3V Output voltage with 1.8V input Voltage Low start-up voltage (when the output current is 1mA) 0.8V The converter output voltage can be adjusted from 2.5V～6.0V(In 0.1V step) Output voltage accuracy 2％ Low temperature-drift coefficient of the output voltage 100ppm/℃ Only three external components are necessary: An inductor, a Schottky diode and an output filter capacitor High power conversion efficiency 85％ Low quiescent current drawn from power source <5.5uA Application Power source for PDA. DSC. MP3 Player. electronic toy and wireless mouse Power source for a single or dual-cell battery-powered equipments Power source for LED Absolute Maximum Ratings Parameter Symbol Max Unit Input supply voltage VIN -0.3~12 V -0.3~6.5 V Lx Voltage CE pin voltage Lx pin output current Power Dissipation SOT-89-3 SOT-23-5 SOT-23-3L TO-92 Operating Junction temperature Storage temperature Ambient Temperature -0.3~Vout+0.3 V 0.7 TJ TS TA 500 250 250 500 125 A mW O C - 40 to 150 O C -40 to 85 O C Note: Exceed these limits to damage to the device. Exposure to absolute maximum rating conditions may affect device reliability. VER 1.3 1 ACE701D PFM STEP-UP DC/DC Converter with High Efficiency and Low Noise Packaging Type SOT-89-3 SOT-23-5 5 1 2 3 1 SOT-23-3L 4 2 TO-92 3 3 1 2 123 SOT-89-3 SOT-23-5 SOT-23-3L TO-92 Description Function 1 4 1 1 VSS(GND) 2 2 2 2 VOUT 3 5 3 3 LX(Ext) Ground pin Output pin, power supply for internal circuits Switching pin 3 NC No connection 1 CE Chip enable pin (active high) Ordering information ACE701D X XX XX + H Halogen - free Pb - free AM : SOT-89-3 BN : SOT-23-5 BM : SOT-23-3L EP : TO-92 Output Voltage : 2.5V / 3.0V ….. 6.0V Function Description : 1 : Internal Tr. Driver, Without Enable circuit 2 : Internal Tr. Driver, With Enable circuit 3 : External Tr. Driver, Without Enable circuit 4 : External Tr. Driver, With Enable circui VER 1.3 2 ACE701D PFM STEP-UP DC/DC Converter with High Efficiency and Low Noise Block Diagram CE pin is only available on 5 pins packages. Recommended Work Conditions Item Min Recommended Max Unit Input Voltage Range 0.8 Inductor 10 27 Input capacitor 0 ≧10 Output capacitor 47 100 Ambient Temperature -40 Vout V 100 μH μF 220 μF 85 ℃ VER 1.3 3 ACE701D PFM STEP-UP DC/DC Converter with High Efficiency and Low Noise Electrical Characteristics Parameter Symbol Output Voltage Test Conditions Vout Input Voltage Vin Input Current Lin Iout=0mA, Vin=Vout*0.6 Start-up voltage Vstart Iout=1mA, Vin:02V Hold-on voltage Quiescent current drawn from power source Switch ON Resistance Vhold Iout=1mA, Vin:20V Without external components, Vout=Vout x 1.05 Rswon LX leakage current ILXleak Vout=Vlx=6V CE “H” threshold voltage VCEH VCE: 02V CE “L” threshold voltage VCEL VCE: 20V Oscillator frequency FOSC LX on “L” side Vout=Vout * 0.96 Oscillator duty cycle Maxdty On (Vlx “L”) side Efficiency η IDD Min Typ Max 2.45 2.5 2.55 2.646 2.7 2.754 2.94 3.0 3.06 3.234 3.3 3.366 3.528 3.6 3.672 3.92 4.0 4.08 4.9 5.0 5.1 5.88 6.0 6.12 0.6 Unit Vout V 12 15 uA 0.8 0.9 V 0.7 4 V 7 0.5 uA Ω 0.5 5 0.8 uA V 0.3 400 70 V 75 V Khz 80 85 % % Note : 1. Diode: Schottky type, such as: 1N5817, 1N5819, 1N5822 2. Inductor: 27uH(R<0.5Ω) 3. Capacitor: 100uF (Tantalum type) Typical Application Circuit D 1N5819 Vin Vout L 27uH LX Cin 47uF LX OUT ACE701D GND Iout Cout 100uF Rload Tan VER 1.3 4 ACE701D PFM STEP-UP DC/DC Converter with High Efficiency and Low Noise Detailed Description The ACE701D series are boost structure, voltage-type pulse-frequency modulation(PFM) step-up DC-DC converter. Only three external components are necessary: an inductor, an output filter capacitor and a schottky diode. And the converter’s low noise and low ripple output voltage can be adjusted from 2.5V to 5.0V, 0.1V step. By using the depletion technics, the quiescent current drawn from power source is lower than 7uA. The high efficiency device consists of resistors for output voltage detection and trimming, a start-up voltage circuit, an oscillator, a reference circuit, a PFM control circuit, a switch protection circuit and a driver transistor. The PFM control circuit is the core of the ACE701D IC. This block controls power switch on duty cycle to stabilize output voltage by calculating results of other blocks which sense input voltage, output voltage, output current and load conditions. In PFM modulation system, the frequency and pulse width is fixed. The duty cycle is adjusted by skipping pulses, so that switch on-time is changed based on the conditions such as input voltage, output current and load. The oscillate block inside ACE701D provides fixed frequency and pulse width wave. The reference circuit provides stable reference voltage to output stable output voltage. Because internal trimming technology is used, The chip output change less than ±2%. At the same time，the problem of temperature-drift coefficient of output voltage is considered in design, so temperature-drift coefficient of output voltage is less than 100ppm/℃。 High-gain differential error amplifier guarantees stable output voltage at difference input voltage and load. In order to reduce ripple and noise, the error amplifier is designed with high band-with. Though at very low load condition, the quiescent current of chip do effect efficiency certainly. The four main energy loss of Boost structure DC-DC converter in full load are the ESR of inductor, the voltage of Schottky diode, on resistor of internal N-channel MOSFET and its driver. In order to improve the efficiency, ACE701D integrates low on-resistor N-channel MOSFET and well design driver circuits. The switch energy loss is limited at very low level. Selection of the External Components Thus it can be seen, the inductor and schottky diode affect the conversion efficiency greatly. The inductor and the capacitor also have great influence on the output voltage ripple of the converter. So it is necessary to choose a suitable inductor, a capacitor and a right schottky diode, to obtain high efficiency, low ripple and low noise. Before discussion，we define D≡Vout-Vin / Vout (1) Inductor Selection Above all, we should define the minimum value of the inductor that can ensure the boost DC-DC to operate in the continuous current-mode condition. Lmin≧D(1-D)2RL / 2f The above expression is got under conditions of continuous current mode, neglect Schottky diode’s voltage, ESR of both inductor and capacitor. The actual value is greater that it. If inductor’s value is less than Lmin，the efficiency of DC-DC converter will drop greatly, and the DC-DC circuit will not be stable. Secondly, consider the ripple of the output voltage, ΔI=D•Vin / Lf Im ax=Vin / (1-D)2RL + DVin / 2Lf VER 1.3 5 ACE701D PFM STEP-UP DC/DC Converter with High Efficiency and Low Noise If inductor value is too small, the current ripple through it will be great. Then the current through diode and power switch will be great. Because the power switch on chip is not ideal switch, the energy of switch will improve. The efficiency will fall. Thirdly，in general, smaller inductor values supply more output current while larger values start up with lower input voltage and acquire high efficiency. An inductor value of 3uH to 1mH works well in most applications. If DC-DC converter delivers large output current (for example: output current is great than 50mA), large inductor value is recommended in order to improve efficiency. If DC-DC must output very large current at low input supply voltage, small inductor value is recommended. The ESR of inductor will effect efficiency greatly. Suppose ESR value of inductor is r L，Rload is load resistor，then the energy can be calculated by following expression: Δη≈ RL / Rload (1-D)2 For example: input 1.5V, output is 3.0V, Rload=20Ω, rL=0.5Ω, The energy loss is 10%. Consider all above，inductor value of 47uH、ESR<0.5Ω is recommended in most applications. Large value is recommended in high efficiency applications and smaller value is recommended (2) Capacitor Selection Ignore ESR of capacitor，the ripple of output voltage is: R=ΔVout / Vout=D / Rload Cf So large value capacitor is needed to reduce ripple. But too large capacitor value will slow down system reaction and cost will improve. So 100uF capacitor is recommended. Larger capacitor value will be used in large output current system. If output current is small (<10mA), small value is needed. Consider ESR of capacitor，ripple will increase： r'=r+Imax•RESR / Vout When current is large, ripple caused by ESR will be main factor. It may be greater than 100mV。The ESR will affects efficiency and increase energy loss. So low-ESR capacitor (for example: tantalum capacitor) is recommend or connect two or more filter capacitors in parallel. (3) Diode Selection Rectifier diode will affects efficiency greatly，Though a common diode (such as 1N4148) will work well for light load，it will reduce about 5%~10% efficiency for heavy load，For optimum performance, a Schottky diode (such as 1N5817、1N5819、1N5822) is recommended. (4) Input Capacitor If supply voltage is stable, the DC-DC circuit can output low ripple, low noise and stable voltage without input capacitor. If voltage source is far away from DC-DC circuit, input capacitor value greater than 10uF is recommended. VER 1.3 6 ACE701D PFM STEP-UP DC/DC Converter with High Efficiency and Low Noise Test Circuits (1) Output voltage test circuit (Iload=1mA) ACE701D (2) Start-up voltage test circuit (Iload=1mA) ACE701D (3) Hold-on voltage test circuit (Iload=1mA) ACE701D VER 1.3 7 ACE701D PFM STEP-UP DC/DC Converter with High Efficiency and Low Noise (4) Quiescent current test circuit ACE701D Note: Vout=Vout_nom*1.05, R=1KΩ, C=0.1uF (5) Oscillator frequency and duty cycle test circuit ACE701D Oscillograph Note: Vin=Vout*0.95, R=1KΩ Electrical Characteristics VER 1.3 8 ACE701D PFM STEP-UP DC/DC Converter with High Efficiency and Low Noise Typical Characteristic (Recommended operating conditions: Cin=47uF, Cout=47uF, Topt=25℃, unless otherwise noted) VER 1.3 9 ACE701D PFM STEP-UP DC/DC Converter with High Efficiency and Low Noise Typical Characteristic(Recommended operating conditions: Cin=47uF, Cout=47uF, Topt=25℃, unless otherwise noted) VER 1.3 10 ACE701D PFM STEP-UP DC/DC Converter with High Efficiency and Low Noise Packing Information SOT-89-3 SOT-23-5 VER 1.3 11 ACE701D PFM STEP-UP DC/DC Converter with High Efficiency and Low Noise Packing Information SOT-23-3L VER 1.3 12 ACE701D PFM STEP-UP DC/DC Converter with High Efficiency and Low Noise Packing Information TO-92 VER 1.3 13 ACE701D PFM STEP-UP DC/DC Converter with High Efficiency and Low Noise Notes ACE does not assume any responsibility for use as critical components in life support devices or systems without the express written approval of the president and general counsel of ACE Electronics Co., LTD. As sued herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and shoes failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. ACE Technology Co., LTD. http://www.ace-ele.com/ VER 1.3 14