AD ADL5501AKSZ-R7

50 MHz to 4 GHz
TruPwr™ Detector
ADL5501
5
FEATURES
True rms response
Excellent temperature stability
Up to 30 dB input dynamic range at 4 GHz
50 Ω input impedance
1.25 V rms, 15 dBm, maximum input
Single-supply operation: 2.7 V to 5.5 V
Low power: 3.3 mW at 3 V supply
RoHS-compliant
OUTPUT (V)
1
0.1
Measurement of CDMA2000-, W-CDMA-, and QPSK-/QAMbased OFDM, and other complex modulation waveforms
RF transmitter or receiver power measurement
0.03
–25
–20
–15
–10
–5
0
5
10
15
INPUT (dBm)
06056-001
APPLICATIONS
Figure 1. Output vs. Input Level, Supply 3 V, Frequency 1.9 GHz
GENERAL DESCRIPTION
The on-chip, 100 Ω series resistance at the output, combined
with an external shunt capacitor, creates a low-pass filter response
that reduces the residual ripple in the dc output voltage. For more
complex waveforms, an external capacitor at the FLTR pin can
be used for supplementary signal demodulation.
The ADL5501 is a mean-responding power detector for use
in high frequency receiver and transmitter signal chains from
50 MHz to 4 GHz. It is easy to apply, requiring only a single
supply between 2.7 V and 5.5 V and a power supply decoupling
capacitor. The input is internally ac-coupled and has a nominal
input impedance of 50 Ω. The output is a linear-responding dc
voltage with a conversion gain of 6.3 V/V rms at 900 MHz.
The ADL5501 offers excellent temperature stability across a
30 dB range and near 0 dB measurement error across temperature
over the top portion of the dynamic range. In addition to its
temperature stability, the ADL5501 offers low process variations
that further reduce calibration complexity.
The ADL5501 is intended for true power measurement of simple
and complex waveforms. The device is particularly useful for
measuring high crest factor (high peak-to-rms ratio) signals,
such as CDMA-, CDMA2000-, W-CDMA-, and QPSK-/QAMbased OFDM waveforms. The on-chip modulation filter provides
adequate averaging for most waveforms.
The ADL5501 operates from −40°C to +85°C and is available in
a small 6-lead SC-70 package. It is fabricated on a proprietary
high fT silicon bipolar process.
FUNCTIONAL BLOCK DIAGRAM
ADL5501
x2
TRANSCONDICTANCE
CELLS
x2
VPOS
FLTR
ERROR
AMP
i
BUFFER
BAND-GAP
REFERENCE
100Ω
VRMS
ENBL
COMM
06056-002
RFIN
INTERNAL FILTER
CAPACITOR
i
Figure 2.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
©2006 Analog Devices, Inc. All rights reserved.
ADL5501
TABLE OF CONTENTS
Features .............................................................................................. 1
Multiple RF Inputs ..................................................................... 18
Applications....................................................................................... 1
Selecting the Square-Domain Filter and Output Low-Pass
Filter ............................................................................................. 18
General Description ......................................................................... 1
Functional Block Diagram .............................................................. 1
Revision History ............................................................................... 2
Specifications..................................................................................... 3
Absolute Maximum Ratings............................................................ 8
ESD Caution.................................................................................. 8
Pin Configuration and Function Descriptions............................. 9
Typical Performance Characteristics ........................................... 10
Circuit Description......................................................................... 16
Filtering........................................................................................ 16
Applications..................................................................................... 17
Basic Connections ...................................................................... 17
Power Consumption, Enable, and Power-On/-Off Response
Time ............................................................................................. 19
Output Drive Capability and Buffering................................... 20
VRMS Output Offset ................................................................. 20
Device Calibration and Error Calculation.............................. 21
Calibration for Improved Accuracy......................................... 21
Drift over a Reduced Temperature Range .............................. 22
Operation Below 100 MHz ....................................................... 22
Evaluation Board ........................................................................ 23
Outline Dimensions ....................................................................... 25
Ordering Guide .......................................................................... 25
Output Swing .............................................................................. 17
Linearity....................................................................................... 17
Input Coupling Using a Series Resistor ................................... 18
REVISION HISTORY
9/06—Revision 0: Initial Version
Rev. 0 | Page 2 of 28
ADL5501
SPECIFICATIONS
TA = 25°C, VS = 3.0 V, CFLTR = Open, COUT = 100 nF, unless otherwise specified.
Table 1.
Parameter
FREQUENCY RANGE
RMS CONVERSION (f = 50 MHz)
Input Impedance
Input Return Loss
Dynamic Range 1
±1 dB Error 2
±2 dB Error2
Maximum Input Level
Minimum Input Level
Conversion Gain
Output Intercept 3
Output Voltage—High Power In
Output Voltage—Low Power In
Temperature Sensitivity
RMS CONVERSION (f = 100 MHz)
Input Impedance
Input Return Loss
Dynamic Range1
±0.25 dB Error 4
±0.25 dB Error2
±1 dB Error2
±2 dB Error2
Maximum Input Level
Minimum Input Level
Conversion Gain
Condition
Input RFIN
Input RFIN to Output VRMS
Min
50
CW input, −40°C < TA < +85°C
VS = 3 V
VS = 5 V
VS = 3 V
VS = 5 V
±1 dB error2
±1 dB error2
VOUT = (Gain × VIN) + Intercept
PIN = 5 dBm, 400 mV rms
PIN = −21 dBm, +20 mV rms
PIN = −5 dBm
25°C ≤ TA ≤ 85°C
−40°C ≤ TA ≤ +25°C
Input RFIN to Output VRMS
CW input, −40°C < TA < +85°C
Delta from 25°C, VS = 5 V
VS = 3 V
VS = 5 V
VS = 3 V
VS = 5 V
VS = 3 V
VS = 5 V
±1 dB error2
±1 dB error2
VOUT = (Gain × VIN) + Intercept
VS = 5 V
Max
4000
Ω||pF
dB
25
26
32
35
+8
−18
4.5
0.03
1.81
0.11
dB
dB
dB
dB
dBm
dBm
V/V rms
V
V
V
0.0039
−0.0037
dB/°C
dB/°C
79||3.6
12.4
Ω||pF
dB
28
19
20
23
27
26
30
+6
−18
6.1
2.47
0.13
dB
dB
dB
dB
dB
dB
dB
dBm
dBm
V/V rms
V/V rms
V
V
V
V
0.0028
−0.0018
dB/°C
dB/°C
7.8
0.03
VS = 5 V
PIN = 5 dBm, 400 mV rms
PIN = −21 dBm, +20 mV rms
PIN = −5 dBm
25°C ≤ TA ≤ 85°C
−40°C ≤ TA ≤ +25°C
Rev. 0 | Page 3 of 28
Unit
MHz
88||6.5
11.0
5.6
Output Intercept3
Output Voltage—High Power In
Output Voltage—Low Power In
Temperature Sensitivity
Typ
−0.02
+0.1
ADL5501
Parameter
RMS CONVERSION (f = 450 MHz)
Input Impedance
Input Return Loss
Dynamic Range1
±0.25 dB Error4
±0.25 dB Error2
±1 dB Error2
±2 dB Error2
Maximum Input Level
Minimum Input Level
Conversion Gain
Output Intercept3
Output Voltage—High Power In
Output Voltage—Low Power In
Temperature Sensitivity
RMS CONVERSION (f = 900 MHz)
Input Impedance
Input Return Loss
Dynamic Range1
±0.25 dB Error4
±0.25 dB Error2
±1 dB Error2
±2 dB Error2
Maximum Input Level
Minimum Input Level
Conversion Gain
Output Intercept3
Output Voltage—High Power In
Output Voltage—Low Power In
Temperature Sensitivity
Condition
Input RFIN to Output VRMS
CW input, −40°C < TA < +85°C
Delta from 25°C, VS = 5 V
VS = 3 V
VS = 5 V
VS = 3 V
VS = 5 V
VS = 3 V
VS = 5 V
±1 dB error2
±1 dB error2
VOUT = (Gain × VIN) + Intercept
PIN = 5 dBm, 400 mV rms
PIN = −21 dBm, +20 mV rms
PIN = −5 dBm
25°C ≤ TA ≤ 85°C
−40°C ≤ TA ≤ +25°C
Input RFIN to Output VRMS
CW input, −40°C < TA < +85°C
Delta from 25°C, VS = 5 V
VS = 3 V
VS = 5 V
VS = 3 V
VS = 5 V
VS = 3 V
VS = 5 V
±1 dB error2
±1 dB error2
VOUT = (Gain × VIN) + Intercept
PIN = 5 dBm, 400 mV rms
PIN = −21 dBm, +20 mV rms
PIN = −5 dBm
25°C ≤ TA ≤ +85°C
−40°C ≤ TA ≤ +25°C
Rev. 0 | Page 4 of 28
Min
Typ
Max
Unit
65||1.4
15.5
Ω||pF
dB
32
20
24
25
29
28
33
+5
−20
7.1
0.03
2.81
0.15
dB
dB
dB
dB
dB
dB
dB
dBm
dBm
V/V rms
V
V
V
0.0016
−0.0002
dB/°C
dB/°C
55||0.9
17
Ω||pF
dB
33
20
23
24
27
27
30
+6
−18
6.3
0.03
2.53
0.14
dB
dB
dB
dB
dB
dB
dB
dBm
dBm
V/V rms
V
V
V
0.0019
−0.0002
dB/°C
dB/°C
ADL5501
Parameter
RMS CONVERSION (f = 1900 MHz)
Input Impedance
Input Return Loss
Dynamic Range1
±0.25 dB Error4
±0.25 dB Error2
±1 dB Error2
±2 dB Error2
Maximum Input Level
Minimum Input Level
Conversion Gain
Output Intercept3
Output Voltage—High Power In
Output Voltage—Low Power In
Temperature Sensitivity
RMS CONVERSION (f = 2350 MHz)
Input Impedance
Input Return Loss
Dynamic Range1
±0.25 dB Error4
±0.25 dB Error2
±1 dB Error2
±2 dB Error2
Maximum Input Level
Minimum Input Level
Conversion Gain
Output Intercept3
Output Voltage—High Power In
Output Voltage—Low Power In
Temperature Sensitivity
Condition
Input RFIN to Output VRMS
CW input, −40°C < TA < +85°C
Delta from 25°C, VS = 5 V
VS = 3 V
VS = 5 V
VS = 3 V
VS = 5 V
VS = 3 V
VS = 5 V
±1 dB error2
±1 dB error2
VOUT = (Gain × VIN) + Intercept
PIN = 5 dBm, 400 mV rms
PIN = −21 dBm, +20 mV rms
PIN = −5 dBm
25°C ≤ TA ≤ 85°C
−40°C ≤ TA ≤ +25°C
Input RFIN to Output VRMS
CW input, −40°C < TA < +85°C
Delta from 25°C, VS = 5 V
VS = 3 V
VS = 5 V
VS = 3 V
VS = 5 V
VS = 3 V
VS = 5 V
±1 dB error2
±1 dB error2
VOUT = (Gain × VIN) + Intercept
PIN = 5 dBm, 400 mV rms
PIN = −21 dBm, +20 mV rms
PIN = −5 dBm
25°C ≤ TA ≤ 85°C
−40°C ≤ TA ≤ +25°C
Rev. 0 | Page 5 of 28
Min
Typ
Max
Unit
36||0.4
14.5
Ω||pF
dB
32
5
7
25
29
28
32
+7
−19
5.5
0.02
2.20
0.12
dB
dB
dB
dB
dB
dB
dB
dBm
dBm
V/V rms
V
V
V
0.0031
−0.0034
dB/°C
dB/°C
32||0.3
13.5
Ω||pF
dB
8
4
7
25
29
29
32
+8
−18
5.0
0.02
2.00
0.10
dB
dB
dB
dB
dB
dB
dB
dBm
dBm
V/V rms
V
V
V
0.0032
−0.0044
dB/°C
dB/°C
ADL5501
Parameter
RMS CONVERSION (f = 2700 MHz)
Input Impedance
Input Return Loss
Dynamic Range1
±0.25 dB Error4
±0.25 dB Error2
±1 dB Error2
±2 dB Error2
Maximum Input Level
Minimum Input Level
Conversion Gain
Output Intercept3
Output Voltage—High Power In
Output Voltage—Low Power In
Temperature Sensitivity
RMS CONVERSION (f = 4000 MHz)
Input Impedance
Input Return Loss
Dynamic Range1
±0.25 dB Error4
±0.25 dB Error2
±1 dB Error2
±2 dB Error2
Maximum Input Level
Minimum Input Level
Conversion Gain
Output Intercept3
Output Voltage—High Power In
Output Voltage—Low Power In
Temperature Sensitivity
OUTPUT OFFSET
ENABLE INTERFACE
Logic Level to Enable Power, HI Condition
Input Current when HI
Logic Level to Disable Power, LO Condition
Power-Up Response Time 5
Condition
Input RFIN to Output VRMS
Min
CW input, −40°C < TA < +85°C
Delta from 25°C, VS = 5 V
VS = 3 V
VS = 5 V
VS = 3 V
VS = 5 V
VS = 3 V
VS = 5 V
±1 dB error2
±1 dB error2
VOUT = (Gain × VIN) + Intercept
PIN = 5 dBm, 400 mV rms
PIN = –21 dBm, +20 mV rms
PIN = –5 dBm
25°C ≤ TA ≤ 85°C
−40°C ≤ TA ≤ +25°C
Input RFIN to Output VRMS
CW input, −40°C < TA < +85°C
Delta from 25°C, VS = 5 V
VS = 3 V
VS = 5 V
VS = 3 V
VS = 5 V
VS = 3 V
VS = 5 V
±1 dB error2
±1 dB error2
VOUT = (Gain × VIN) + Intercept
PIN = 5 dBm, 400 mV rms
PIN = –21 dBm, +20 mV rms
PIN = –5 dBm
25°C ≤ TA ≤ 85°C
−40°C ≤ TA ≤ +25°C
No signal at RFIN
Pin ENBL
2.7 V ≤ VS ≤ 5.5 V, −40°C < TA < +85°C
2.7 V at ENBL, –40°C ≤ TA ≤ +85°C
2.7 V ≤ VS ≤ 5.5 V, −40°C < TA < +85°C
CFLTR = COUT = Open, 0 dBm at RFIN
CFLTR = 1 nF, COUT = Open, 0 dBm at RFIN
CFLTR = Open, COUT = 100 nF, 0 dBm at RFIN
Rev. 0 | Page 6 of 28
Typ
Max
Unit
31||−0.1
12.5
Ω||pF
dB
5
3
7
25
30
28
33
+8
−17
4.6
0.02
1.84
0.09
dB
dB
dB
dB
dB
dB
dB
dBm
dBm
V/V rms
V
V
V
0.0034
−0.0049
dB/°C
dB/°C
36||−0.4
11.8
Ω||pF
dB
5
4
5
28
31
30
33
+10
−18
3.8
0.01
1.53
0.07
dB
dB
dB
dB
dB
dB
dB
dBm
dBm
V/V rms
V
V
V
0.0019
−0.0043
dB/°C
dB/°C
50
150
mV
0.05
VPOS
0.1
+0.5
V
μA
V
μs
μs
μs
1.8
–0.5
6
21
28
ADL5501
Parameter
POWER SUPPLIES
Operating Range
Quiescent Current
Total Supply Current When Disabled
Condition
Min
−40°C < TA < +85°C
No signal at RFIN 6
No signal at RFIN, ENBL Input LO
2.7
1
The available output swing, and hence, the dynamic range, is altered by the supply voltage; see Figure 8.
Error referred to best-fit line at 25°C.
Calculated using linear regression.
4
Error referred to delta from 25°C response; see Figure 13, Figure 14, Figure 15, Figure 19, Figure 20, and Figure 21.
5
The response time is measured from 10% to 90% of settling level; see Figure 30.
6
Supply current is input-level dependent; see Figure 6.
2
3
Rev. 0 | Page 7 of 28
Typ
1.1
0.1
Max
Unit
5.5
V
mA
μA
<10
ADL5501
ABSOLUTE MAXIMUM RATINGS
Table 2.
Parameter
Supply Voltage VS
VRMS
RFIN
Equivalent Power, re 50 Ω
Internal Power Dissipation
θJA (SC-70)
Maximum Junction Temperature
Operating Temperature Range
Storage Temperature Range
Rating
5.5 V
0 V, VS
1.25 V rms
15 dBm
80 mW
494°C/W
125°C
−40°C to +85°C
−65°C to +150°C
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
ESD CAUTION
Rev. 0 | Page 8 of 28
ADL5501
VPOS
1
FLTR
2
RFIN
3
ADL5501
TOP VIEW
(Not to Scale)
6
VRMS
5
ENBL
4
COMM
06056-003
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
Figure 3. Pin Configuration
Table 3. Pin Function Descriptions
Pin No.
1
2
Mnemonic
VPOS
FLTR
3
4
5
RFIN
COMM
ENBL
6
VRMS
Description
Supply Voltage Pin. Operational range 2.7 V to 5.5 V.
Square-Domain Filter Pin. Connection for an external capacitor to lower the corner frequency of the squaredomain (or modulation) filter. Capacitor is connected between FLTR and VS and forms a low-pass filter with an
8 kΩ on-chip resistor. The on-chip capacitor provides filtering with an approximate 100 kHz corner frequency.
For simple waveforms, no further filtering of the demodulated signal is required.
Signal Input Pin. Internally ac-coupled after internal termination resistance. Nominal 50 Ω input impedance.
Device Ground Pin.
Enable Pin. Connect pin to VS for normal operation. Connect pin to ground for disable mode for a supply
current less than 1 μA.
Output Pin. Rail-to-rail voltage output with limited 3 mA current drive capability. The output has an internal
100 Ω series resistance. High resistive loads are recommended to preserve output swing.
Rev. 0 | Page 9 of 28
ADL5501
TYPICAL PERFORMANCE CHARACTERISTICS
TA = 25°C, VS = 5.0 V, CFLTR = open, COUT = 100 nF, Colors: black = +25°C, blue = −40°C, red = +85°C, unless otherwise noted.
10
3
100MHz
450MHz
900MHz
1900MHz
2350MHz
2700MHz
4000MHz
2
–20
–15
–10
–5
0
5
10
0
–1
–2
15
INPUT (dBm)
–3
–25
–20
–15
–10
–5
0
5
10
06056-007
0.1
0.03
–25
ERROR (dB)
100MHz
450MHz
900MHz
1900MHz
2350MHz
2700MHz
4000MHz
06056-004
OUTPUT (V)
1
1
15
INPUT (dBm)
Figure 4. Output vs. Input Level; Frequencies100 MHz, 450 MHz,
900 MHz,1900 MHz, 2350 MHz, 2700 MHz, and 4000 MHz; Supply 5.0 V
Figure 7. Linearity Error vs. Input Level; Frequencies 100 MHz, 450 MHz,
900 MHz, 1900 MHz, 2350 MHz, 2700 MHz, and 4000 MHz; Supply 5.0 V
5.0
10
5.5V
4.5
5.0V
4.0
3.0V
OUTPUT (V)
3.0
2.5
100MHz
450MHz
900MHz
1900MHz
2350MHz
2700MHz
4000MHz
1.5
1.0
0.5
0
0
0.2
0.4
0.6
0.8
1.0
1.2
2.7V
1
0.1
1.4
INPUT (V rms)
0.03
–25
–20
–15
–10
–5
0
5
10
15
INPUT (dBm)
Figure 5. Output vs. Input Level (Linear Scale); Frequencies 100 MHz, 450 MHz,
900 MHz, 1900 MHz, 2350 MHz, 2700 MHz, and 4000 MHz; Supply 5.0 V
06056-008
2.0
06056-005
OUTPUT (V)
3.5
Figure 8. Output vs. Input Level;
Supply 2.7 V, 3.0 V, 5.0 V, and 5.5 V; Frequency 900 MHz
12
18
11
16
5.0V
8
RETURN LOSS (dB)
9
3.0V
7
6
5
4
14
12
3
10
2
0
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
INPUT (V rms)
Figure 6. Supply Current vs. Input Level; Supplies 3.0 V and 5.0 V;
Temperatures −40°C, +25°C, and +85°C
8
0
1
2
3
FREQUENCY (GHz)
Figure 9. Return Loss vs. Frequency
Rev. 0 | Page 10 of 28
4
06056-009
1
06056-006
SUPPLY CURRENT (mA)
10
3
2
2
1
1
–1
–1
–2
–2
–20
–15
–10
–5
0
5
10
15
INPUT (dBm)
–3
–25
2
1
1
ERROR (dB)
2
–1
–2
–2
–15
–10
–5
0
5
10
15
INPUT (dBm)
–3
–25
2
2
1
1
ERROR (dB)
3
–2
–2
–10
–5
INPUT (dBm)
0
5
10
15
06056-012
–1
–15
10
15
–20
–15
–10
–5
0
5
10
15
0
–1
–20
5
Figure 14. Output Delta from 25°C Output Voltage for 50 Devices
at −40°C and +85°C, Frequency 1900 MHz, Supply 5.0 V
3
–3
–25
0
INPUT (dBm)
Figure 11. Temperature Drift Distributions for 50 Devices at −40°C, +25°C, and
+85°C vs. +25°C Linear Reference; Frequency 1900 MHz; Supply 5.0 V
0
–5
0
–1
06056-011
ERROR (dB)
3
–20
–10
Figure 13. Output Delta from 25°C Output Voltage for 50 Devices
at −40°C and +85°C, Frequency 900 MHz, Supply 5.0 V
3
–3
–25
–15
INPUT (dBm)
Figure 10. Temperature Drift Distributions for 50 Devices at −40°C, +25°C, and
+85°C vs. +25°C Linear Reference; Frequency 900 MHz; Supply 5.0 V
0
–20
06056-014
–3
–25
ERROR (dB)
0
Figure 12. Temperature Drift Distributions for 50 Devices at −40°C, +25°C, and
+85°C vs. +25°C Linear Reference; Frequency 2350 MHz; Supply 5.0 V
Rev. 0 | Page 11 of 28
–3
–25
–20
–15
–10
–5
0
5
10
15
INPUT (dBm)
Figure 15. Output Delta from 25°C Output Voltage for 50 Devices
at −40°C and +85°C, Frequency 2350 MHz, Supply 5.0 V
06056-015
0
06056-013
ERROR (dB)
3
06056-010
ERROR (dB)
ADL5501
3
2
2
1
1
–1
–1
–2
–2
–20
–15
–10
–5
0
5
10
15
INPUT (dBm)
–3
–25
2
1
1
ERROR (dB)
2
–1
–2
–2
–15
–10
–5
0
5
10
15
INPUT (dBm)
–3
–25
2
2
1
1
ERROR (dB)
3
–2
–2
–10
–5
INPUT (dBm)
0
5
10
15
06056-018
–1
–15
10
15
–20
–15
–10
–5
0
5
10
15
0
–1
–20
5
Figure 20. Output Delta from 25°C Output Voltage for 50 Devices
at −40°C and +85°C, Frequency 3500 MHz, Supply 5.0 V
3
–3
–25
0
INPUT (dBm)
Figure 17. Temperature Drift Distributions for 50 Devices at −40°C, +25°C, and
+85°C vs. +25°C Linear Reference; Frequency 3500 MHz; Supply 5.0 V
0
–5
0
–1
06056-017
ERROR (dB)
3
–20
–10
Figure 19. Output Delta from 25°C Output Voltage for 50 Devices
at −40°C and +85°C, Frequency 2700 MHz, Supply 5.0 V
3
–3
–25
–15
INPUT (dBm)
Figure 16. Temperature Drift Distributions for 50 Devices at −40°C, +25°C, and
+85°C vs. +25°C Linear Reference; Frequency 2700 MHz; Supply 5.0 V
0
–20
06056-020
–3
–25
ERROR (dB)
0
Figure 18. Temperature Drift Distributions for 50 Devices at −40°C, +25°C, and
+85°C vs. +25°C Linear Reference; Frequency 4000 MHz; Supply 5.0 V
Rev. 0 | Page 12 of 28
–3
–25
–20
–15
–10
–5
0
5
10
15
INPUT (dBm)
Figure 21. Output Delta from 25°C Output Voltage for 50 Devices
at −40°C and +85°C, Frequency 4000 MHz, Supply 5.0 V
06056-021
0
06056-019
ERROR (dB)
3
06056-016
ERROR (dB)
ADL5501
ADL5501
5
3
CW
QPSK, 4.8dB CF
2
8PSK, 4.8dB CF
16QAM, 6.3dB CF
1
VOUT (V)
ERROR (dB)
1
–5
0
5
10
INPUT (dBm)
Figure 22. Output vs. Input Level with Different Waveforms, 10 MHz Signal BW
for All Modulated Signals, Supply 5.0 V, Frequency 1900 MHz
2
2
1
1
ERROR (dB)
3
–1
–3
–25
–20
–15
–10
–5
0
5
10
3
CW
12.2kbps, DPCCH (–5.46dB, 15kSPS) +
DPDCH (0dB, 60kSPS), 3.4dB CF
64kbps, DPCCH (–9.54dB, 15kSPS) +
DPDCH (0dB, 240kSPS), 3.4dB CF
144kbps, DPCCH (–11.48dB, 15kSPS) +
DPDCH (0dB, 480kSPS), 3.3dB CF
384kbps, DPCCH (–11.48dB, 15kSPS) +
DPDCH (0dB, 960kSPS), 3.3dB CF
768kbps, DPCCH (–11.48dB, 15kSPS) +
DPDCH1 + 2 (0dB, 960kSPS), 5.8dB CF
2
ERROR (dB)
1
–1
–2
–2
–15
–10
–5
RFIN (dBm)
0
5
CW
BPSK, 11dB CF
QPSK, 11dB CF
16QAM, 12dB CF
64QAM, 11dB CF
10
–20
–15
–10
–5
0
5
10
Figure 24. Error from CW Linear Reference vs. Input with Various
W-CDMA Up Link Waveforms at 1900 MHz, CFLTR = Open, COUT = 100 nF
CW
PICH, 4.7dB CF
PICH + FCH (9.6kbps), 4.8dB CF
PICH + FCH (9.6kbps) + DCCH, 6.3dB CF
PICH + FCH (9.6kbps) + SCH (153.6kbps), 6.7dB CF
PICH + FCH (9.6kbps) + DCCH +
SCH (153.6kbps), 7.6dB CF
0
–1
–20
10
Figure 26. Error from CW Linear Reference vs. Input Level for Various
802.16 OFDM Waveforms at 3.5 GHz, 10 MHz Signal BW, and
256 Subcarriers for All Modulated Signals, Supply 5.0 V
0
–3
–25
5
RFIN (dBm)
–3
–25
06056-024
ERROR (dB)
1
0
0
–3
–25
Figure 23. Error from CW Linear Reference vs. Input Level for Various
802.16 OFDM Waveforms at 2.35 GHz, 10 MHz Signal BW, and
256 Subcarriers for All Modulated Signals, Supply 5.0 V
2
–5
–2
RFIN (dBm)
3
–10
–1
CW
BPSK, 11dB CF
QPSK, 11dB CF
16QAM, 12dB CF
64QAM, 11dB CF
–2
–15
Figure 25. Error from CW Linear Reference vs. Input with Different Waveforms,
10 MHz Signal BW for All Modulated Signals, Supply 5.0 V, Frequency 1900 MHz
3
0
–20
INPUT (dBm)
06056-023
ERROR (dB)
–3
–25
06056-025
–10
06056-026
–15
–20
–15
–10
–5
RFIN (dBm)
0
5
10
06056-027
–20
–2
06056-022
0.03
–25
0
–1
CW
QPSK
8PSK
16QAM
64QAM
0.1
64QAM, 7.4dB CF
Figure 27. Error from CW Linear Reference vs. Input with Various
CDMA2000 Reverse Link Waveforms at 900 MHz, CFLTR = 1 nF, COUT = 100 nF
Rev. 0 | Page 13 of 28
ADL5501
2
ERROR (dB)
1
3
1 w/
1 w/
1 w/
1 w/
1 w/
1 w/
16 DPCH,
32 DPCH,
64 DPCH,
64 DPCH,
64 DPCH,
64 DPCH,
1 CARRIER
1 CARRIER
1 CARRIER
2 CARRIERS
3 CARRIERS
4 CARRIERS
2
0
–1
–1
–2
–2
–15
–10
–5
0
5
10
RFIN (dBm)
–3
–25
06056-028
–20
PILOT CHANNEL, 1 CARRIER
9 CHANNEL, 1 CARRIER
9 CHANNEL, 3 CARRIERS
9 CHANNEL, 4 CARRIERS
1
0
–3
–25
CW
SR1,
SR1,
SR1,
SR1,
Figure 28. Error from CW Linear Reference vs. Input with Various
WCDMA Down Link Waveforms at 2140 MHz, CFLTR = 1 nF, COUT = 100 nF
–20
–15
–10
–5
0
5
10
INPUT (dBm)
06056-031
CW
TEST MODEL
TEST MODEL
TEST MODEL
TEST MODEL
TEST MODEL
TEST MODEL
ERROR (dB)
3
Figure 31. Error from CW Linear Reference vs. Input with Various
CDMA2000 Fwd Link Waveforms at 2140 MHz, CFLTR = 1 nF, COUT = 100 nF
PULSED
RFIN
ADL5501
VPOS
VRMS
6
COUT
CFLTR
RF PULSE
GENERATOR
2
FLTR
ENBL
5
3
RFIN
COMM
4
ROUT
400mV rms RF INPUT
250mV rms
160mV rms
70mV rms
06056-032
1
FET PROBE
40µs/DIV
Figure 29. Hardware Configuration for Output Response to RF Input Pulse
Figure 32. Output Response to Various RF Input Pulse Levels, Supply 3 V,
Frequency 900 MHz, CFLTR = 1 nF, COUT = Open, ROUT = Open
PULSED RFIN
400mV rms RF INPUT
400mV rms RF INPUT
VRMS (500mV/DIV)
VRMS (500mV/DIV)
PULSED
RFIN
250mV rms
160mV rms
70mV rms
250mV rms
160mV rms
40µs/DIV
06056-030
70mV rms
100µs/DIV
Figure 30. Output Response to Various RF Input Pulse Levels, Supply 3 V,
Frequency 900 MHz, CFLTR = Open, COUT = Open, ROUT = Open
06056-033
POWER
SUPPLY
C2
0.1µF
06056-029
C1
100pF
VRMS (500mV/DIV)
OSCILLOSCOPE
Figure 33. Output Response to Various RF Input Pulse Levels, Supply 3 V,
Frequency 900 MHz, CFLTR = Open, COUT = 0.1 μF, ROUT = 1 kΩ
Rev. 0 | Page 14 of 28
ADL5501
ENBL
OSCILLOSCOPE
POWER
SUPPLY
FET PROBE
ADL5501
1
VPOS
VRMS
6
2
FLTR
ENBL
5
3
RFIN
COMM
4
COUT
CFLTR
PULSE
GENERATOR
ROUT
250mV rms
160mV rms
70mV rms
AD811
50Ω
06056-034
RF SIGNAL
GENERATOR
400mV rms RF INPUT
732Ω
06056-037
C2
0.1µF
VRMS (500mV/DIV)
C1
100pF
40µs/DIV
Figure 37. Output Response to Enable Gating at Various RF Input Levels,
Supply 3 V, Frequency 900 MHz, CFLTR = 1 nF, COUT = Open, ROUT = Open
Figure 34. Hardware Configuration for Output Response to
Enable Gating Measurements
ENBL
ENBL
400mV rms RF INPUT
VRMS (500mV/DIV)
250mV rms
160mV rms
250mV rms
160mV rms
70mV rms
06056-035
70mV rms
40µs/DIV
100µs/DIV
Figure 38. Output Response to Enable Gating at Various RF Input Levels,
Supply 3 V, Frequency 900 MHz, CFLTR = Open, COUT = 0.1 μF, ROUT = 1 kΩ
100
7
80
6
60
INTERCEPT (mV)
8
5
4
40
20
0
500
1000
1500
2000
2500
3000
3500
FREQUENCY (MHz)
4000
–20
0
500
1000
1500
2000
2500
3000
3500
FREQUENCY (MHz)
Figure 39. Intercept vs. Frequency, Supply 5 V
Figure 36. Conversion Gain vs. Frequency, Supply 5 V
Rev. 0 | Page 15 of 28
4000
06056-039
0
3
06056-036
CONVERSION GAIN (V/V rms)
Figure 35. Output Response to Enable Gating at Various RF Input Levels,
Supply 3 V, Frequency 900 MHz, CFLTR = Open, COUT = Open, ROUT = Open
2
06056-038
VRMS (500mV/DIV)
400mV rms RF INPUT
ADL5501
CIRCUIT DESCRIPTION
The ADL5501 is an rms-responding (mean power) detector that
provides an approach to the exact measurement of RF power that is
independent of waveform. It achieves this function by using a
proprietary technique in which the outputs of two identical
squaring cells are balanced by the action of a high gain error
amplifier.
The signal to be measured is applied to the input of the first
squaring cell through the input matching network. The input
is matched to offer a broadband 50 Ω input impedance from
50 MHz to 4 GHz. The input matching network has a high-pass
corner frequency of approximately 70 MHz.
The ADL5501 responds to the voltage, VIN, at its input by squaring
this voltage to generate a current proportional to VIN2. This current
is applied to an internal load resistor in parallel with a capacitor,
followed by a low-pass filter, which extracts the mean of VIN2.
Although essentially voltage responding, the associated input
impedance calibrates this port in terms of equivalent power.
Therefore, 1 mW corresponds to a voltage input of 224 mV rms
referenced to 50 Ω. Because both the squaring cell input impedance
and the input matching network are frequency dependent, the
conversion gain is a function of signal frequency.
The voltage across the low-pass filter, whose frequency can be
arbitrarily low, is applied to one input of an error-sensing
amplifier. A second identical voltage-squaring cell is used to
close a negative feedback loop around this error amplifier. This
second cell is driven by a fraction of the quasi-dc output voltage
of the ADL5501. When the voltage at the input of the second
squaring cell is equal to the rms value of VIN, the loop is in a stable
state, and the output then represents the rms value of the input.
By completing the feedback path through a second squaring
cell, identical to the one receiving the signal to be measured,
several benefits arise. First, scaling effects in these cells cancel;
therefore, the overall calibration can be accurate, even though
the open-loop response of the squaring cells taken separately
need not be. Note that in implementing rms-dc conversion, no
reference voltage enters into the closed-loop scaling. Second,
the tracking in the responses of the dual cells remains very close
over temperature, leading to excellent stability of calibration.
The squaring cells have very wide bandwidth with an intrinsic
response from dc to microwave. However, the dynamic range of
such a system is small, due in part to the much larger dynamic
range at the output of the squaring cells. There are practical
limitations to the accuracy of sensing very small error signals at
the bottom end of the dynamic range, arising from small random
offsets that limit the attainable accuracy at small inputs.
On the other hand, the squaring cells in the ADL5501 have a
Class AB aspect; the peak input is not limited by its quiescent
bias condition but is determined mainly by the eventual loss of
square-law conformance. Consequently, the top end of their
response range occurs at a large input level (approximately
700 mV rms), while preserving a reasonably accurate square-law
response. The maximum usable range is, in practice, limited by
the output swing. The rail-to-rail output stage can swing from a
few millivolts above ground to within 100 mV below the supply.
An example of the output induced limit, given a conversion gain
of 6.3 V/V rms at 900 MHz and assuming a maximum output of
2.9 V with a 3 V supply, has a maximum input of 2.9 V rms/6.3 or
460 mV rms.
FILTERING
An important aspect of rms-dc conversion is the need for
averaging (the function is root-mean-square). The on-chip
averaging in the square domain has a corner frequency of
approximately 100 kHz and is sufficient for common modulation signals, such as CDMA-, WCDMA-, and QPSK-/QAMbased OFDM (for example, WLAN and WiMAX).
For more complex RF waveforms (with modulation components
extending down into the kilohertz region), more filtering is
necessary to supplement the on-chip, low-pass filter. For this
reason, the FLTR pin is provided; a capacitor attached between
this pin and VPOS can extend the averaging time to very low
frequencies.
Adequate filtering ensures the accuracy of the rms measurement;
however, some ripple or ac residual can still be present on the
dc output. To reduce this ripple, an external shunt capacitor can
be used at the output to form a low-pass filter with the on-chip,
100 Ω resistance (see the Selecting the Square-Domain Filter
and Output Low-Pass Filter section).
Rev. 0 | Page 16 of 28
ADL5501
APPLICATIONS
BASIC CONNECTIONS
LINEARITY
Figure 40 shows the basic connections for the ADL5501. The
device is powered by a single supply of between 2.7 V and 5.5 V,
with a quiescent current of 1.1 mA. The VPOS pin is decoupled
using 100 pF and 0.1 μF capacitors.
Because the ADL5501 is a linear-responding device, plots of
output voltage vs. input voltage result in a straight line. It is more
useful to plot the error on a logarithmic scale, as shown in
Figure 42. The deviation of the plot for the ideal straight-line
characteristic is caused by output clipping at the high end and
by signal offsets at the low end. However, it should be noted that
offsets at the low end can be either positive or negative; therefore,
this plot could also trend upwards at the low end. Figure 10
through Figure 12 and Figure 16 through Figure 18 show error
distributions for a large population of devices at specific
frequencies.
+VS 2.7V TO 5.5V
100pF
0.1µF
ADL5501
1
VPOS
VRMS
VRMS
6
COUT
CFLTR
2
FLTR
ENBL
5
3
RFIN
COMM
4
3
100MHz
450MHz
900MHz
1900MHz
2350MHz
2700MHz
4000MHz
06056-040
2
Figure 40. Basic Connections for ADL5501
OUTPUT SWING
At 900 MHz, the output voltage is nominally 6.3 times the input
rms voltage (a conversion gain of 6.3 V/V rms). The output voltage
swings from near ground to 4.9 V on a 5.0 V supply.
1
ERROR (dB)
RFIN
–1
–2
Figure 41 shows the output swing of the ADL5501 to a CW input
for various supply voltages. It is clear from Figure 41 that
operating the device at lower supply voltages reduces the
dynamic range as the output headroom decreases.
10
5.0V
OUTPUT (V)
–3
–25
2.7V
1
–15
–10
–5
INPUT (dBm)
0
5
10
15
–10
–5
0
5
10
15
Figure 42. Representative Unit, Error in dB vs. Input Level, VS = 5.0 V
06056-041
–20
–15
INPUT (dBm)
0.1
0.03
–25
–20
It is also apparent in Figure 42 that the error plot tends to shift
to the right with increasing frequency. The squaring cell has an
input impedance that decreases with frequency. The matching
network compensates for the change and maintains the input
impedance at a nominal 50 Ω. The result is a decrease in the
actual voltage across the squaring cell as the frequency increases,
reducing the conversion gain. Similarly, conversion gain is less
at frequencies near 100 MHz because of the small on-chip
coupling capacitor.
5.5V
3.0V
0
06056-042
The ADL5501 RF input does not require external termination
components because it is internally matched for an overall
broadband input impedance of 50 Ω.
Figure 41. Output Swing for Supply Voltages of 2.7 V, 3.0 V, 5.0 V, and 5.5 V
Rev. 0 | Page 17 of 28
ADL5501
BAND 1
Figure 43 shows a technique for coupling the input signal into
the ADL5501 that can be applicable where the input signal is
much larger than the input range of the ADL5501. A series
resistor combines with the input impedance of the ADL5501
to attenuate the input signal. Because this series resistor forms
a divider with the frequency dependent input impedance, the
apparent gain changes greatly with frequency. However, this
method has the advantage of very little power being tapped off
in RF power transmission applications. If the resistor is large
compared to the transmission line’s impedance, the VSWR of
the system is relatively unaffected.
RSERIES
ADL5501
Figure 43. Attenuating the Input Signal
The resistive tap or series resistance, RSERIES, can expressed as
RSERIES = RIN (1 − 10ATTN/20)/(10ATTN/20)
(1)
where:
RIN is the input impedance of RFIN.
ATTN is the desired attenuation factor in dB.
For example, if a power amplifier with a maximum output power
of +28 dBm is matched to the ADL5501 input at +5 dBm, then
a −23 dB attenuation factor is required. At 900 MHz, the input
resistance, RIN, is 55 Ω.
RSERIES = (55 Ω)(1 − 10−23/20)/(10−23/20) = 722 Ω
50Ω
BAND 2
DIRECTIONAL
COUPLER
16.5Ω
16.5Ω
RFIN
50Ω
16.5Ω
ADL5501
Figure 44. Combining Multiple RF Input Signals
SELECTING THE SQUARE-DOMAIN FILTER AND
OUTPUT LOW-PASS FILTER
The internal filter capacitor of the ADL5501 provides averaging
in the square domain but leaves some residual ac on the output.
Signals with high peak-to-average ratios, such as W-CDMA or
CDMA2000, can produce ac-residual levels on the ADL5501
dc output. To reduce the effects of these low frequency components
in the waveforms, some additional filtering is required.
RFIN
06056-043
RFIN
DIRECTIONAL
COUPLER
06056-044
INPUT COUPLING USING A SERIES RESISTOR
(2)
Thus, for an attenuation of −23 dB, a series resistance of
approximately 722 Ω is needed.
MULTIPLE RF INPUTS
Figure 44 shows a technique for combining multiple RF input
signals to the ADL5501. Some applications can share a single
detector for multiple bands. Three 16.5 Ω resistors in a T-network
combine the three 50 Ω terminations (including the ADL5501).
The broadband resistive combiner ensures each port of the
T-network sees a 50 Ω termination. Because there are only 6 dB
of isolation from one port of the combiner to the other ports,
only one band should be active at a time.
The square-domain filter capacitance of the ADL5501 can be
augmented by connecting a capacitor between Pin 2 (FLTR) and
Pin 1 (VPOS). In addition, the output of the ADL5501 can be
filtered directly by placing a capacitor between VRMS (Pin 6)
and ground. The combination of the on-chip, 100 Ω output
series resistance and the external shunt capacitor forms a lowpass filter to reduce the residual ac.
Table 4 shows the effect of several capacitor values for various
communications standards with high peak-to-average ratios
along with the residual ripple at the output, in peak-to-peak and
rms volts. Note that large load capacitances increase the turn-on
and pulse response times (see Figure 30, Figure 32, Figure 33,
Figure 35, Figure 37, and Figure 38). For more information on
the effects of the filter capacitances on the response, see the
Power Consumption, Enable, and Power-On/-Off Response
Time section.
Rev. 0 | Page 18 of 28
ADL5501
1 nF,
0.1 μF
W-CDMA RL
(3.4 dB CF)
1 nF,
Open
Open,
0.1 μF
1 nF,
0.1 μF
CDMA2000 DL
(6.7 dB CF)
1 nF,
Open
Open,
0.1 μF
1 nF,
0.1 μF
W-CDMA UL
TM1-64, 1 CR
1 nF,
Open
Open,
0.1 μF
1 nF,
0.1 μF
Residual AC
mV p-p
mV rms
83
11
175
21
394
47
49
5.5
98
11
212
23
45
5.5
93
11
200
24
6.4
0.8
19
2.6
52
6.6
4.5
0.6
16
2.2
36
4.9
3.1
0.5
9.6
1.4
27
3.9
67
8.6
148
19
339
43
28
3.9
56
7.9
119
17
26
3.7
52
7.7
116
17
204
32
396
64
840
140
60
11
112
21
227
42
56
11
114
21
243
45
The turn-on time and pulse response is strongly influenced by
the size of the square-domain filter and output shunt capacitor.
Figure 45 shows a plot of the output response to an RF pulse on
the RFIN pin, with a 0.1 μF output filter capacitor and no
square-domain filter capacitor. The falling edge is particularly
dependent on the output shunt capacitance, as shown in Figure 45.
PULSED RFIN
400mV rms RF INPUT
The ADL5501 can be disabled either by pulling the ENBL (Pin 5)
to COMM (Pin 4) or by removing the supply power to the device.
Disabling the device via the ENBL function reduces the leakage
current to less than 1 μA.
160mV rms
70mV rms
2ms/DIV
Figure 45. Output Response to Various RF Input Pulse Levels,
Supply 3 V, Frequency 900 MHz,
Square-Domain Filter Open, Output Filter 0.1 μF
To improve the falling edge of the enable and pulse responses,
a resistor can be placed in parallel with the output shunt capacitor.
The added resistance helps to discharge the output filter
capacitor. Although this method reduces the power-off time,
the added load resistor also attenuates the output (see the
Output Drive Capability and Buffering section).
PULSED RFIN
400mV rms RF INPUT
POWER CONSUMPTION, ENABLE, AND POWERON/-OFF RESPONSE TIME
The quiescent current consumption of the ADL5501 varies with
the size of the input signal from approximately 1.1 mA for no
signal up to 6.2 mA at an input level of 0.7 V rms (10 dBm,
re 50 Ω). If the input is driven beyond this point, the supply
current increases sharply (as shown in Figure 6). There is little
variation in quiescent current with power supply voltage.
250mV rms
06056-045
Open,
0.1 μF
Output
V dc
0.5
1.0
2.0
0.5
1.0
2.0
0.5
1.0
2.0
0.5
1.0
2.0
0.5
1.0
2.0
0.5
1.0
2.0
0.5
1.0
2.0
0.5
1.0
2.0
0.5
1.0
2.0
0.5
1.0
2.0
0.5
1.0
2.0
0.5
1.0
2.0
250mV rms
160mV rms
70mV rms
2ms/DIV
06056-046
CFILT, COUT
1 nF,
Open
VRMS (500mV/DIV)
Waveform
64QAM
(7.4 dB CF)
If the input of the ADL5501 is driven while the device is disabled
(ENBL = COMM), the leakage current of less than 1 μA increases
as a function of input level. When the device is disabled, the
output impedance increases to approximately 33.5 kΩ.
VRMS (500mV/DIV)
Table 4. Waveform and Output Filter Effects on Residual AC
Figure 46. Output Response to Various RF Input Pulse Levels,
Supply 3 V, Frequency 900 MHz,
Square-Domain Filter Open, Output Filter 0.1 μF with Parallel 1 kΩ
The square-domain filter improves the rms accuracy for high
crest factors (see the Selecting the Square-Domain Filter and
Output Low-Pass Filter), but it can hinder the response time.
For optimum response time and low ac residual, both the
square-domain filter and the output filter should be used.
Rev. 0 | Page 19 of 28
ADL5501
5V
The square-domain filter at FLTR can be reduced to improve
response time, and the remaining ac residual can be decreased
by using the output filter, which has a smaller time constant.
0.1µF
100pF
0.01µF
VPOS
OUTPUT DRIVE CAPABILITY AND BUFFERING
VRMS
The ADL5501 is capable of sourcing an output current of
approximately 3 mA. The output current is sourced through the
on-chip, 100 Ω series resistor; therefore, any load resistor forms
a voltage divider with this on-chip resistance.
It is recommended that the ADL5501 drive high resistive loads
to preserve output swing. If an application requires driving a low
resistance load, a simple buffering circuit can be used, as shown
in Figure 49. Similar circuits can be used to increase or decrease
the nominal conversion gain (see Figure 47 and Figure 48). In
Figure 48, the AD8031 buffers a resistive divider to give half of
the slope. In Figure 47, the op amp gain of two doubles the slope.
Using other resistor values, the slope can be changed to an arbitrary
value. The AD8031 rail-to-rail op amp, used in these examples,
can swing from 50 mV to 4.95 V on a single 5 V supply and
operates at supply voltages down to 2.7 V. If high output current
is required (>10 mA), the AD8051, which also has rail-to-rail
capability, can be used down to a supply voltage of 3 V. It can
deliver up to 45 mA of output current.
AD8031
ADL5501
6.3V/V rms
06056-049
COMM
Figure 49. Output Buffering Options, Slope of 6.3 V/V rms at 900 MHz
VRMS OUTPUT OFFSET
The ADL5501 has a ±1 dB error detection range of about 30 dB,
as shown in Figure 10 to Figure 12 and Figure 16 to Figure 18.
The error is referred to the best-fit line defined in the linear region
of the output response. Below an input power of −20 dBm, the
response is no longer linear and begins to lose accuracy. In
addition, depending on the supply voltage, saturation of the
output limits the detection accuracy above 10 dBm. Calibration
points should be chosen in the linear region, avoiding the
nonlinear ranges at the high and low extremes.
10
5V
100pF
1
OUTPUT (V)
0.1µF
0.01µF
VPOS
VRMS
AD8031
ADL5501
12.6V/V rms
0.1
COMM
0.01
–40
0.1µF
ADL5501
5kΩ
–15
–10
–5
0
5
10
15
3.2V/V rms
0.01µF
AD8031
–20
Figure 50 shows the distribution of the output response vs. the
input power for multiple devices. The ADL5501 loses accuracy at
low input powers as the output response begins to fan out. As the
input power is reduced, the spread of the output response increases
along with the error. Although some devices follow the ideal linear
response at very low input powers, not all devices continue the
ideal linear regression to a near 0 V y-intercept. Some devices
exhibit output responses that rapidly decrease, and some flatten
out. With no RF signal applied, the ADL5501 has a typical output
offset of 50 mV (with a maximum of 150 mV).
06056-048
COMM
–25
Figure 50. Output vs. Input Level Distribution of 50 Devices,
Frequency 900 MHz, Supply 5.0 V
VPOS
4kΩ
–30
5V
100pF
VRMS
–35
INPUT (dBm)
Figure 47. Output Buffering Options, Slope of 12.6 V/V rms at 900 MHz
06056-050
06056-047
5kΩ
5kΩ
Figure 48. Output Buffering Options, Slope of 3.2 V/V rms at 900 MHz
Rev. 0 | Page 20 of 28
ADL5501
DEVICE CALIBRATION AND ERROR CALCULATION
CALIBRATION FOR IMPROVED ACCURACY
Because slope and intercept vary from device to device, boardlevel calibration must be performed to achieve high accuracy.
In general, calibration is performed by applying two input power
levels to the ADL5501 and measuring the corresponding output
voltages. The calibration points are generally chosen to be within
the linear operating range of the device. The best-fit line is characterized by calculating the conversion gain (or slope) and intercept
using the following equations:
Another way of presenting the error function of the ADL5501
is shown in Figure 52. In this case, the dB error at hot and cold
temperatures is calculated with respect to the transfer function
at ambient. This is a key difference in comparison to the previous
plots. Up to now, the errors were calculated with respect to the
ideal linear transfer function at ambient. When this alternative
technique is used, the error at ambient becomes equal to 0 by
definition (see Figure 52).
Gain = (VRMS2 − VRMS1)/(VIN2 − VIN1)
(3)
Intercept = VRMS1 − (Gain × VIN1)
(4)
where:
VIN is the rms input voltage to RFIN.
VRMS is the voltage output at VRMS.
Once gain and intercept are calculated, an equation can be
written that allows calculation of an (unknown) input power
based on the measured output voltage.
VIN = (VRMS − Intercept)/Gain
(5)
For an ideal (known) input power, the law conformance error of
the measured data can be calculated as
ERROR (dB) =
20 × log [(VRMS, MEASURED − Intercept)/(Gain × VIN, IDEAL)] (6)
Figure 51 includes a plot of the error at 25°C, the temperature at
which the ADL5501 is calibrated. Note that the error is not zero.
This is because the ADL5501 does not perfectly follow the ideal
linear equation, even within its operating region. The error at
the calibration points is, however, equal to 0 by definition.
This plot is a useful tool for estimating temperature drift at a
particular power level with respect to the (nonideal) response at
ambient. The linearity and dynamic range tend to be improved
artificially with this type of plot because the ADL5501 does not
perfectly follow the ideal linear equation (especially outside of
its linear operating range). Achieving this level of accuracy in
an end application requires calibration at multiple points in the
operating range of the device.
In some applications, very high accuracy is required at just one
power level or over a reduced input range. For example, in a
wireless transmitter, the accuracy of the high power amplifier
(HPA) is most critical at or close to full power. The ADL5501
offers a tight error distribution in the high input power range,
as shown in Figure 52. The high accuracy range, centered around
9 dBm at 1900 MHz, offers 7 dB of ±0.1 dB detection error over
temperature. Multiple point calibration at ambient temperature
in the reduced range offers precise power measurement with
near 0 dB error from −40°C to +85°C.
3
2
3
1
ERROR (dB)
2
+85°C
+25°C
–40°C
–1
0
–2
–40°C
–1
–3
–25
–2
–20
–15
–10
–5
–20
–15
–10
–5
INPUT (dBm)
0
5
10
15
06056-051
INPUT (dBm)
–3
–25
+25°C
0
Figure 51. Error from Linear Reference vs. Input at −40°C, +25°C, and
+85°C vs. +25°C Linear Reference, Frequency 1900 MHz, Supply 5.0 V
Figure 51 also includes error plots for the output voltage at
−40°C and +85°C. These error plots are calculated using the
gain and intercept at 25°C. This is consistent with calibration in
a mass-production environment where calibration at temperature
is not practical.
0
5
10
15
06056-052
ERROR (dB)
1
+85°C
Figure 52. Error from +25°C Output Voltage at −40°C, +25°C, and +85°C
After Ambient Normalization, Frequency 1900 MHz, Supply 5.0 V
The high accuracy range center varies over frequency. At
1900 MHz, the region is centered at approximately 9 dBm.
At higher frequencies, the high accuracy range is centered
at higher input powers (see Figure 13 through Figure 15 and
Figure 19 through Figure 21).
Rev. 0 | Page 21 of 28
ADL5501
DRIFT OVER A REDUCED TEMPERATURE RANGE
–2
–3
–25
0.25
–15
–10
–5
0
5
10
15
Figure 55. Output Delta from +25°C Output Voltage for 12 Devices at −40°C
and +85°C, Frequency 50 MHz, Supply 5.0 V
–0.25
–0.50
OPERATION BELOW 100 MHZ
–0.75
The ADL5501 works at frequencies below 100 MHz, but
exhibits slightly higher linearity error. Figure 54 shows the error
distribution of 12 devices at 50 MHz over temperature. When
compared to an ideal linear transfer function at ambient, the
error of the ADL5501 over temperature remains within ±0.5 dB
for the central 20 dB of the dynamic range. At the higher input
power levels, the error grows as the response becomes nonlinear.
–1.00
–25
–20
–15
–10
–5
0
5
10
15
INPUT (dBm rms)
Figure 53. Typical Drift at 1.9 GHz for Various Temperatures
3
2
Due to the repeatability of the performance from part to part,
compensation can be applied to reduce the effects of temperature
drift and linearity error. To detect larger dynamic ranges at
lower frequencies, the transfer function at ambient can be
calibrated, thus eliminating the linearity error. This technique
is discussed in detail in the Calibration for Improved Accuracy
section. Figure 55 shows that the dynamic range within ±0.5 dB
error improves to 30 dB by using this method.
1
ERROR (dB)
–20
INPUT (dBm)
0
06056-100
ERROR (dB)
0.50
0
–1
+15°C
0°C
–10°C
–25°C
–40°C
+85°C
+70°C
+50°C
+35°C
+25°C
0.75
1
06056-054
1.00
2
ERROR (dB)
Figure 53 shows the error over temperature for a 1.9 GHz input
signal. Error due to drift over temperature consistently remains
within ±0.25 dB and only begins to exceed this limit when the
ambient temperature goes above +25°C and below −10°C. For
all frequencies using a reduced temperature range, higher
measurement accuracy is achievable.
3
0
–1
–3
–25
–20
–15
–10
–5
INPUT (dBm)
0
5
10
15
06056-053
–2
Figure 54. Temperature Drift Distributions for 12 Devices at −40°C, +25°C,
and +85°C vs. +25°C Linear Reference; Frequency 50 MHz; Supply 5.0 V
Rev. 0 | Page 22 of 28
ADL5501
A simple (and common) example of such a problem is triple
travel due to mismatch at both the source and the evaluation
board. Here the signal from the source reaches the evaluation
board and mismatch causes a reflection. When that reflection
reaches the source mismatch, it causes a new reflection, which
travels back to the evaluation board, adding to the original signal
incident at the board. The resultant voltage varies with both
cable length and frequency dependence on the relative phase of
the initial and reflected signals. Placing the 3 dB pad at the input of
the board improves the match at the board and, thus, reduces
the sensitivity to mismatches at the source. When such precautions are taken, measurements are less sensitive to cable length and
other fixture issues. In an actual application when the distance
between ADL5501 and source is short and well defined, this 3 dB
attenuator is not needed.
EVALUATION BOARD
Figure 56 shows the schematic of the ADL5501 evaluation
board. The layout and silkscreen of the evaluation board layers
are shown in Figure 57 to Figure 60. The board is powered by
a single supply in the 2.7 V to 5.5 V range. The power supply is
decoupled by 100 pF and 0.1 μF capacitors. Table 5 details the
various configuration options of the evaluation board.
Problems caused by impedance mismatch can arise using the
evaluation board to examine the ADL5501 performance. One
way to reduce these problems is to put a coaxial 3 dB attenuator
on the RFIN SMA connector. Mismatches at the source, cable,
and cable interconnection, as well as those occurring on the
evaluation board, can cause these problems.
TO EDGE
CONNECTOR
C2
0.1µF
VPOS
ADL5501
1
VPOS
VRMS
R3
0Ω
6
C3
(OPEN)
RFIN
R5
(OPEN)
2
FLTR
ENBL
5
3
RFIN
COMM
4
C4
100nF
VPOS
VRMS
R2
(OPEN)
SW1
R1
(OPEN)
ENBL
R4
49.9Ω
TO EDGE
CONNECTOR
06056-056
C1
100pF
Figure 56. Evaluation Board Schematic
Table 5. Evaluation Board Configuration Options
Component
VPOS, GND
C1, C2
Description
Ground and Supply Vector Pins.
Power Supply Decoupling. The nominal supply decoupling of 100 pF and 0.1 μF.
C3
Filter Capacitor. The internal averaging capacitor can be augmented by placing additional
capacitance in C3.
Output Filtering. The combination of the internal 100 Ω output resistance and C4 produce
a low-pass filter to reduce output ripple. The output can also be scaled down using the
resistor divider pads, R3 and R2. In addition, resistors and capacitors can be placed in C4 and
R2 to load test VRMS.
Device Enable. When the switch is set toward the SW1 label, the ENBL pin is connected to VPOS
and the ADL5501 is in operating mode. In the opposite switch position, the ENBL pin is grounded
(through the 49.9 Ω resistor), putting the device in power-down mode. While in this switch
position, the ENBL pin can be driven by a signal generator via the SMA labeled ENBL. In this
case, R4 serves as a termination resistor for generators requiring a 50 Ω match.
Alternate Interface. R1and R5 allow for VRMS and ENBL to be accessible from the edge
connector, which is used only for characterization.
R2, R3, C4
R4, SW1
R1, R5
Rev. 0 | Page 23 of 28
Default Condition
Not Applicable
C1 = 100 pF (Size 0402)
C2 = 0.1 μF (Size 0402)
C3 = Open (Size 0402)
R2 = Open (Size 0402)
R3 = 0 Ω (Size 0402)
C4 = 100 nF (Size 0402)
R4 = 49.9 Ω (Size 0402)
SW1 = toward SW1 label
R1 = Open (Size 0402)
R5 = Open (Size 0402)
06056-059
06056-057
ADL5501
Figure 59. Silkscreen of Component Side
06056-058
06056-060
Figure 57. Layout of Component Side
Figure 60. Silkscreen of Circuit Side
Figure 58. Layout of Circuit Side
Rev. 0 | Page 24 of 28
ADL5501
OUTLINE DIMENSIONS
2.20
2.00
1.80
1.35
1.25
1.15
6
5
4
1
2
3
2.40
2.10
1.80
PIN 1
0.65 BSC
1.30 BSC
1.00
0.90
0.70
1.10
0.80
0.10 MAX
0.30
0.15
0.40
0.10
SEATING
PLANE
0.46
0.36
0.26
0.22
0.08
0.10 COPLANARITY
COMPLIANT TO JEDEC STANDARDS MO-203-AB
Figure 61. 6-Lead Thin Shrink Small Outline Transistor Package [SC-70]
(KS-6)
Dimensions shown in millimeters
ORDERING GUIDE
Model
ADL5501AKSZ-R7 1
ADL5501AKSZ-R21
ADL5501-EVALZ1
1
Temperature Range
–40°C to +85°C
–40°C to +85°C
Package Description
6-Lead SC-70, 7” Tape and Reel
6-Lead SC-70, 7” Tape and Reel
Evaluation Board
Z = Pb-free part.
Rev. 0 | Page 25 of 28
Package Option
KS-6
KS-6
Branding
Q0Z
Q0Z
Ordering
Quantity
3,000
250
ADL5501
NOTES
Rev. 0 | Page 26 of 28
ADL5501
NOTES
Rev. 0 | Page 27 of 28
ADL5501
NOTES
©2006 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D06056-0-9/06(0)
Rev. 0 | Page 28 of 28