Data Sheet SINGLE PHASE FULL WAVE DIRECT PWM MOTOR DRIVER General Description Features The AM4961 is a full wave driver IC with PWM control function. It is used for single phase motor and is capable of speed control by changing output duty cycle. · · · · · · · · The AM4961 is available in TSSOP-20(EDP) and HTSSOP-14 packages. AM4961 Built-in Hall Bias Circuit Built-in PWM Speed Control Circuit Built-in Minimal Speed Setup Circuit Rotation Speed Indication (FG) Rotation or Lock State Indication (RD) Built-in Thermal Shutdown Circuit Lock Protection Output Current Limit Application · · CPU Cooler Fan in PC Brushless DC Motor Driver HTSSOP-14 TSSOP-20(EDP) Figure 1. Package Types of AM4961 Jun. 2008 Rev. 2. 2 BCD Semiconductor Manufacturing Limited 1 Data Sheet SINGLE PHASE FULL WAVE DIRECT PWM MOTOR DRIVER AM4961 Pin Configuration G Package (TSSOP-20(EDP)) PGND 1 20 PGND PGND 2 19 PGND PGND 3 18 PGND OUT2 4 17 OUT1 VCC 5 16 GND VMIN 6 15 CT VPWM 7 14 VREF COSC 8 13 HIN- FG 9 12 HB RD 10 11 HIN+ Jun. 2008 Rev. 2. 2 BCD Semiconductor Manufacturing Limited 2 Data Sheet SINGLE PHASE FULL WAVE DIRECT PWM MOTOR DRIVER AM4961 Pin Configuration (Continued) GH Package (HTSSOP-14) PGND PGND OUT2 1 14 OUT1 VCC 2 13 GND VMIN 3 12 CT VPWM 4 11 VREF COSC 5 10 HIN- FG 6 9 HB RD 7 8 HIN+ Figure 2. Pin Configuration of AM4961 (Top View) Jun. 2008 Rev. 2. 2 BCD Semiconductor Manufacturing Limited 3 Data Sheet SINGLE PHASE FULL WAVE DIRECT PWM MOTOR DRIVER AM4961 Pin Description Pin Number Pin Name TSSOP-20(EDP) Function HTSSOP-14 1 PGND Power ground 2 PGND Power ground 3 PGND Power ground 4 1 OUT2 Driver output 2 5 2 VCC Power supply 6 3 VMIN Minimum duty setting 7 4 VPWM Adjustable Input 8 5 COSC Oscillator capacitor 9 6 FG Rotation speed indicator 10 7 RD Rotation/lock state indicator 11 8 HIN+ 12 9 HB 13 10 HIN- Hall sensor input - 14 11 VREF Reference voltage regulator 15 12 CT 16 13 GND Ground for control circuit 17 14 OUT1 Driver output 1 18 PGND Power ground 19 PGND Power ground 20 PGND Power ground Hall sensor input + Hall sensor bias regulator Lock and rotation setting capacitor terminal Jun. 2008 Rev. 2. 2 BCD Semiconductor Manufacturing Limited 4 Data Sheet SINGLE PHASE FULL WAVE DIRECT PWM MOTOR DRIVER AM4961 Functional Block Diagram 9 (6) COSC VPWM VMIN 8 (5) Oscillation Circuit FG Thermal Shutdown 7 (4) 10 (7) 6 (3) RD Pre-driver VREF HB HIN+ HIN- 14 (11) 12 (9) Voltage Reference 5 (2) VCC Control Circuit Hall Bias 4 (1) 11 (8) OUT2 13 (10) Hysteresis Amp Lock Shutdown and Auto Restart 16 (13) 15 (12) CT A (B) A for 20-pin 17 (14) OUT1 1, 2, 3, 18, 19, 20 GND PGND B for 14-pin Figure 3. Functional Block Diagram of AM4961 Jun. 2008 Rev. 2. 2 BCD Semiconductor Manufacturing Limited 5 Data Sheet SINGLE PHASE FULL WAVE DIRECT PWM MOTOR DRIVER AM4961 Truth Table HIN- HIN+ H L L H H L L H H L L COSC (Note 1) H L L H H H L L H CT H L OUT1 OUT2 FG H L L L H OFF OFF L L L OFF OFF H OFF L OFF H OFF OFF OFF L OFF OFF OFF RD Mode Rotation (Drive) L Rotation (Recirculate) OFF Lock Protection Note 1: VOSC (H) >VPWM, VOSC (L) <VPWM. Ordering Information AM4961 E1: Lead Free G1: Green Circuit Type TR: Tape and Reel Blank: Tube Package G: TSSOP-20(EDP) GH: HTSSOP-14 Package Temperature Range TSSOP-20 (EDP) -30 to 105oC HTSSOP-14 -30 to 90oC Part Number Lead Free Marking ID Green Lead Free Green Packing Type AM4961G-E1 AM4961G-G1 AM4961G AM4961G-G1 Tube AM4961GTR-E1 AM4961GTR-G1 AM4961G AM4961G-G1 Tape & Reel AM4961GH-E1 AM4961GH-G1 AM4961GH AM4961GH-G1 Tube AM4961GHTR-E1 AM4961GHTR-G1 AM4961GH AM4961GH-G1 Tape & Reel BCD Semiconductor's Pb-free products, as designated with "E1" suffix in the part number, are RoHS compliant. Products with "G1" suffix are available in green packages. Jun. 2008 Rev. 2. 2 BCD Semiconductor Manufacturing Limited 6 Data Sheet SINGLE PHASE FULL WAVE DIRECT PWM MOTOR DRIVER AM4961 Absolute Maximum Ratings (Note 2) Parameter Symbol Value Unit Supply Voltage VCC 18 V Output Current IOUT 1.2 A Output Voltage VOUT 18 V IHB 10 mA VPWM 6 V RD Output Voltage VRD 18 V FG Output Voltage VFG 18 V RD Output Current IRD 10 mA FG Output Current IFG 10 mA Power Dissipation (Note 3) PD Storage Temperature Range TSTG -55 to 150 oC ESD (Human Body Model) ESD 2000 V ESD (Machine Model) ESD 250 V HB Output Current VPWM Input Voltage TSSOP-20(EDP) 1.5 W HTSSOP-14 1.1 W Note 2: Stresses greater than those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "Recommended Operating Conditions" is not implied. Exposure to "Absolute Maximum Ratings" for extended periods may affect device reliability. Note 3: TA=25oC, no external heatsink. Recommended Operating Conditions Parameter Symbol Min Typ Max Unit Supply Voltage VCC 3.5 12 16 V Hall Input Voltage + (Note 4) VIN+ 0.2 3 V Hall Input Voltage - (Note 4) VIN- 0.2 3 V TA -30 105 Ambient Temperature (Note 5) o C Note 4: Hall input voltage range includes the amplitude of signal. Note 5: For TSSOP-20(EDP) package only. External heatsink shall larger than 15.24mm*3.81mm to ensure the IC is available at TA=105oC. Jun. 2008 Rev. 2. 2 BCD Semiconductor Manufacturing Limited 7 Data Sheet SINGLE PHASE FULL WAVE DIRECT PWM MOTOR DRIVER AM4961 Electrical Characteristics (VCC=12V, TA=25oC, unless otherwise specified.) Parameter Symbol Conditions Min Typ Max Unit IQ1 Lock off 11.24 15 18.76 IQ2 Lock on 6.25 8 10.55 5.8 6 6.2 V mA Quiescent Current VREF Voltage VREF IREF=5mA Output Saturation Voltage at High Side VSATH ISOURCE=200mA 1.0 1.17 V Output Saturation Voltage at Low Side VSATL ISINK=200mA 0.2 0.3 V 18 25 32 KHz COSC Frequency fOSC COSC=100pF COSC High Level Voltage VOSCH 3.45 3.6 3.75 V COSC Low Level Voltage VOSCL 1.83 1.95 2.07 V Hall Input Hysteresis VHYS ±10 ±20 mV Hall Bias Voltage VHB 1.1 1.25 1.4 V CT High Level Voltage VCTH 3.55 3.7 3.88 V CT Low Level Voltage VCTL 1.55 1.7 1.85 V CT Charge Current ICHG 1.5 2 2.55 µA CT Discharge Current IDHG 0.14 0.2 0.255 µA CT Charge and Discharge Ratio RCD ICHG/IDHG 8.5 10 14.5 FG Output Low Level Voltage VFGL IFG=5mA 0.2 0.3 V FG Leakage Current ILFG VFG=12V 30 µA RD Output Low Level Voltage VRDL IRD=5mA 0.3 V RD Leakage Current ILRD VRD=12V 30 µA IHB=5mA Jun. 2008 Rev. 2. 2 0.2 BCD Semiconductor Manufacturing Limited 8 Data Sheet SINGLE PHASE FULL WAVE DIRECT PWM MOTOR DRIVER AM4961 Typical Performance Characteristics 20 20 TA=25 C Rotation Mode Rotation Mode 16 12 12 IQ1 (mA) IQ1 (mA) 16 O VCC=12V 8 8 4 4 0 -50 0 0 50 100 150 4 200 6 8 10 O 12 14 16 18 VCC (V) TA ( C) Figure 5. Quiescent Current vs. Supply Voltage Figure 4.Quiescent Current vs. Ambient Temperature 2.0 2.0 VCC=12V VCC=12V 1.5 VSATL (V) VSATH (V) 1.5 1.0 1.0 0.5 0.5 0.0 0.0 0 200 400 600 800 0 1000 200 400 600 800 1000 IOUT (mA) IOUT (mA) Figure 6. Output Saturation Voltage (High) vs. Output Current Jun. 2008 Rev. 2. 2 Figure 7. Output Saturation Voltage (Low) vs. Output Current BCD Semiconductor Manufacturing Limited 9 Data Sheet SINGLE PHASE FULL WAVE DIRECT PWM MOTOR DRIVER AM4961 Typical Performance Characteristics (Continued) 1.2 2.8 1.0 External Heatsink Size:15.24mm*3.81mm 2.4 0.8 PD (W) PD (W) 2.0 1.6 0.6 1.2 No External Heatsink 0.4 0.8 0.2 0.4 Package: TSSOP-20(EDP) Package: HTSSOP-14 No External Heatsink 0.0 0.0 0 40 80 105 120 -20 160 0 20 40 60 80 90 100 O O TA ( C) TA ( C) Figure 8. Power Dissipation vs. Ambient Temperature Figure 9. Power Dissipation vs. Ambient Temperature Jun. 2008 Rev. 2. 2 BCD Semiconductor Manufacturing Limited 10 Data Sheet SINGLE PHASE FULL WAVE DIRECT PWM MOTOR DRIVER AM4961 Operating Diagram VPWM adjustable Voltage Lowest speed setting voltage fOSC=25kHz (COSC=100pF) Vosc VMIN Voltage COSC Output Vosc Low Speed PWM Variable High Speed VCC 0V FG Output Figure 10. Operating Diagram of AM4961 (Note 6) Note 6: 1. Low Speed Setting Mode M When VPWM voltage is higher than VMIN pin voltage, motor speed is settable by VMIN pin voltage. The minimum drive duty cycle is settable by comparing COSC oscillating voltage and VMIN pin voltage. VPWM voltage is decided by variation of PWM duty. At a certain PWN duty, when VPWM voltage is lower than the low side of COSC output voltage, the motor will run at full speed. 2. Variable Speed Setting Mode When VPWM voltage is lower than VMIN pin voltage, PWM control system works by comparing VPWM voltage and COSC voltage. If VPWM voltage is higher, the ON duty cycle of the upper side transistors will be minimized and motor speed becomes lower. Vice versa. 3. Full Speed Rotation Mode Jun. 2008 Rev. 2. 2 BCD Semiconductor Manufacturing Limited 11 Data Sheet SINGLE PHASE FULL WAVE DIRECT PWM MOTOR DRIVER AM4961 Typical Application VCC D1 R1 27k C1 1µF or greater L1 AM4961 R2 10k 4 (1) 5 (2) 6 (3) R4 39k 7 (4) R6 330k PWM R3 7.5k 8 (5) 9 (6) 10 (7) OUT2 OUT1 VCC GND VMIN CT VPWM VREF COSC HIN- FG HB RD PGND HIN+ 17 (14) 16 (13) 15 (12) 14 (11) 13 (10) 12 (9) 11 (8) Hall C4 0.47µF 1,2,3,18,19,20 R7 100k C2 0.33µF R8 R5 C3 100pF 68k 100k Figure 11. Typical Application of AM4961 (Note 7) Jun. 2008 Rev. 2. 2 BCD Semiconductor Manufacturing Limited 12 Data Sheet SINGLE PHASE FULL WAVE DIRECT PWM MOTOR DRIVER AM4961 Typical Application (Continued) Note 7: *7. HB Pin *1. Ground Line Layout This pin is available to output a 1.25V Hall bias voltage. PGND is connected to motor supply stage and GND is connected to control stage. All ground lines from control stage are connected to GND. *8. VMIN Pin If this pin is disused, connect it directly with VPWM, the minimum duty cycle will be 10%. *2. Stability of Power Supply *9. Exposed Pad (For TSSOP-20(EDP) package only) C1 is employed to stabilize VCC. Its capacitance is no less than 1µF. *3. Hall Input EXPOSED PAD To avoid noise, the shortest line is recommended to connect with Hall stage which has about 20mV hysteresis. Thus, the ideal Hall input is 50mV or over. *9 *4. COSC Capacitor When CCP is 100pF, the COSC frequency will be 25kHz. There is an exposed pad at the bottom of IC. If operating current is high, it is recommended to solder external heatsink closely with this pad by tin to ensure better temperature characteristics. *5. FG Output FG output terminal is open collector output which varies with phase change. *6. RD Output RD output terminal is open collector output. It is low at rotation mode and high when stopped. Jun. 2008 Rev. 2. 2 BCD Semiconductor Manufacturing Limited 13 Data Sheet SINGLE PHASE FULL WAVE DIRECT PWM MOTOR DRIVER AM4961 Mechanical Dimensions TSSOP-20(EDP) Unit: mm(inch) 6.400(0.252) 6.600(0.260) 4.100(0.161) 4.300(0.169) 2.900(0.114) 3.100(0.122) 6.200(0.244) 6.600(0.260) EXPOSED PAD 4.300(0.169) 4.500(0.177) #1 PIN INDEX0.750(0.030)Dp0.000(0.000) 0.850(0.033) 0.100(0.004) 0.100(0.004) 0.190(0.007) 0.650(0.026)TYP 0.900(0.035) 1.050(0.041) 0.340(0.013) 0.540(0.021) 4-10° 14° TOP & BOTTOM 0.200(0.008)MIN R0.090(0.004)MIN 1.200(0.047) MAX 0.050(0.002) R0.090(0.004)MIN 0.150(0.006) 0.250(0.010)TYP 0° 8° 0.200(0.008) 0.280(0.011) 0.450(0.018) 0.750(0.030) Jun. 2008 Rev. 2. 2 1.000(0.039) REF BCD Semiconductor Manufacturing Limited 14 Data Sheet SINGLE PHASE FULL WAVE DIRECT PWM MOTOR DRIVER AM4961 Mechanical Dimensions (Continued) HTSSOP-14 Unit: mm(inch) 1.470(0.058) 1.570(0.062) 6.350(0.250) 6.550(0.258) Φ 1.450(0.057) 1.550(0.061) 6.200(0.244) 6.600(0.260) 4.300(0.160) 4.500(0.177) SEE DETAIL A Φ 0.750(0.030) 0.850(0.033) 0.650(0.026) BSC 1.300(0.051) BSC 0.200(0.008) MIN 1.200(0.047) MAX 10° 14 ° R0.090(0.004) MIN 0.340(0.013) 0.540(0.021) R0.090(0.004) MIN 0.250(0.010) BSC 0.050(0.002) 0.200(0.008) 0.900(0.035) 1.050(0.041) 0° 8° 0.450(0.018) 0.750(0.030) 1.000(0.039) REF DETAIL A Jun. 2008 Rev. 2. 2 BCD Semiconductor Manufacturing Limited 15 BCD Semiconductor Manufacturing Limited http://www.bcdsemi.com IMPORTANT NOTICE BCD Semiconductor Manufacturing Limited reserves the right to make changes without further notice to any products or specifications herein. BCD Semiconductor Manufacturing Limited does not assume any responsibility for use of any its products for any particular purpose, nor does BCD Semiconductor Manufacturing Limited assume any liability arising out of the application or use of any its products or circuits. BCD Semiconductor Manufacturing Limited does not convey any license under its patent rights or other rights nor the rights of others. MAIN SITE - Headquarters BCD Semiconductor Manufacturing Limited BCD Semiconductor Manufacturing Limited - Wafer Fab No. 1600, Zi Xing Road, Shanghai ZiZhu Science-basedLimited Industrial Park, 200241, China Shanghai SIM-BCD Semiconductor Manufacturing Tel: Fax: +86-21-24162277 800,+86-21-24162266, Yi Shan Road, Shanghai 200233, China Tel: +86-21-6485 1491, Fax: +86-21-5450 0008 REGIONAL SALES OFFICE Shenzhen OfficeSALES OFFICE REGIONAL - Wafer FabSemiconductor Manufacturing Limited BCD Shanghai SIM-BCD Semiconductor Manufacturing Co., Ltd. - IC Design Group 800 Yi Shan Road, Shanghai 200233, China Corporation Advanced Analog Circuits (Shanghai) Tel: +86-21-6485 1491,YiFax: 0008200233, China 8F, Zone B, 900, Shan+86-21-5450 Road, Shanghai Tel: +86-21-6495 9539, Fax: +86-21-6485 9673 Taiwan Office Shanghai Semiconductor Manufacturing Co., Ltd., Shenzhen Office BCD Taiwan Semiconductor Shenzhen SIM-BCD Office Office (Taiwan) Company Limited Room E, 5F, Noble Center, No.1006,Manufacturing 3rd Fuzhong Road, Futian District,Office Shenzhen, 4F, 298-1, Guang Road,(Taiwan) Nei-Hu District, Taipei, Shanghai SIM-BCD Semiconductor Co., Ltd. Shenzhen BCDRui Semiconductor Company Limited 518026, China Taiwan Advanced Analog Circuits (Shanghai) Corporation Shenzhen Office 4F, 298-1, Rui Guang Road, Nei-Hu District, Taipei, Tel: +86-755-8826 Tel: +886-2-2656 2808 Room E, 5F, Noble 7951 Center, No.1006, 3rd Fuzhong Road, Futian District, Shenzhen 518026, China Taiwan Fax: +86-755-88267951 7865 Fax: +886-2-2656 28062808 Tel: +86-755-8826 Tel: +886-2-2656 Fax: +86-755-8826 7865 Fax: +886-2-2656 2806 USA Office BCD Office Semiconductor Corp. USA 30920Semiconductor Huntwood Ave.Corporation Hayward, BCD CA 94544, USA Ave. Hayward, 30920 Huntwood Tel :94544, +1-510-324-2988 CA U.S.A Fax:: +1-510-324-2988 +1-510-324-2788 Tel Fax: +1-510-324-2788