ATMEL ATAM893X

Features
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Extended Temperature Range for Very High Temperature up to 125°C
4-Kbyte EEPROM Program Memory
EEPROM Programmable Options
Read Protection for the EEPROM Program Memory
16 Bi-directional I/Os
Up to Seven External/Internal Interrupt Sources
Eight Hardware and Software Interrupt Priorities
Multifunction Timer/Counter with Prescaler/Interval Timer
Programmable System-clock with Prescaler and Five Different Clock
Sources
Wide Supply Voltage Range (1.8 V to 6.5 V)
Very Low Sleep Current (< 1 µA)
2 × 512-bit EEPROM Data Memory
256 × 4-bit RAM Data Memory
Synchronous Serial Interface (2-wire, 3-wire)
Watchdog, POR and Brown-out Function
Voltage Monitoring Inclusive Lo_BAT Detect
Multi-chip Link for U3280M
Flash Version
for ATAR080,
ATAR090/890
and
ATAR092/892
ATAM893-D
Description
The ATAM893-D is the Multiple Times Programmable (MTP) version for the MARC4
ROM types ATAR080, ATAR090/890 and ATAR092/892. The MTP is designed with
EEPROM cells so it can be programmed several times. To offer full compatibility with
each ROM version, the I/O configuration is stored into a separate internal EEPROM
block during programming. The configuration is downloaded to the I/Os with every
power-on reset.
Figure 0-1.
Block Diagram
VSS
VDD
Brown-out protect.
RESET
Voltage monitor
External input
OSC2
OSC1
RC
oscillators
Crystal
oscillators
External
clock input
Clock management
VMI
BP10
Port 1
EEPROM
RAM
4 K x 8 bit
256 x 4 bit
BP23
Timer 3
4-bit CPU core
8-bit
timer/counter
with modulator
and demodulator
I/O bus
Data direction +
alternate function
Port 4
T2I
T2O
SSI
Serial interface
MARC4
Data direction
BP22
Port 2
BP21
Timer 2
8/12-bit timer
with modulator
SD
BP13
BP20/NTE
UTCM
Timer 1
interval- and
watchdog timer
Data direction +
interrupt control
Data direction +
alternate function
Port 5
BP40
BP42
BP50
BP52
INT3
T2O
INT1
INT6
SC
BP41
BP43
BP51
BP53
VMI
INT3
INT6
INT1
T2I
SD
T3O
T3I
EEPROM
2 x 32 x 16 bit
Port 6
BP60
T3O
SC
BP63
T3I
Rev. 4680C–4BMCU–01/05
1. Pin Configuration
Figure 1-1.
Pinning SSO20 Package
VDD
BP40/INT3/SC
BP53/INT1
BP52/INT1
BP51/INT6
BP50/INT6
OSC1
OSC2
BP60/T3O
BP10
Table 1-1.
Name
2
1
2
3
4
5
6
7
8
9
10
20
19
18
17
16
15
14
13
12
11
VSS
BP43/INT3/SD
BP42/T2O
BP41/VMI/T2I
BP23
BP22
BP21
BP20/NTE
BP63/T3I
BP13
Pin Description
Type
Function
Alternate Function
Pin No.
Reset State
VDD
Supply voltage
–
1
NA
VSS
Circuit ground
–
20
NA
BP10
I/O
Bi-directional I/O line of Port 1.0
–
10
Input
BP13
I/O
Bi-directional I/O line of Port 1.3
–
11
Input
BP20
I/O
Bi-directional I/O line of Port 2.0
NTE test mode enable, see section “Master Reset”
13
Input
BP21
I/O
Bi-directional I/O line of Port 2.1
–
14
Input
BP22
I/O
Bi-directional I/O line of Port 2.2
–
15
Input
BP23
I/O
Bi-directional I/O line of Port 2.3
–
16
Input
BP40
I/O
Bi-directional I/O line of Port 4.0
SC-serial clock or INT3 external interrupt input
2
Input
BP41
I/O
Bi-directional I/O line of Port 4.1
VMI voltage monitor input or T2I external clock input
Timer 2
17
Input
BP42
I/O
Bi-directional I/O line of Port 4.2
T2O Timer 2 output
18
Input
BP43
I/O
Bi-directional I/O line of Port 4.3
SD serial data I/O or INT3-external interrupt input
19
Input
BP50
I/O
Bi-directional I/O line of Port 5.0
INT6 external interrupt input
6
Input
BP51
I/O
Bi-directional I/O line of Port 5.1
INT6 external interrupt input
5
Input
BP52
I/O
Bi-directional I/O line of Port 5.2
INT1 external interrupt input
4
Input
BP53
I/O
Bi-directional I/O line of Port 5.3
INT1 external interrupt input
3
Input
BP60
I/O
Bi-directional I/O line of Port 6.0
T3O Timer 3 output
9
Input
BP63
I/O
Bi-directional I/O line of Port 6.3
T3I Timer 3 input
12
Input
7
Input
8
Input
OSC1
I
Oscillator input
4-MHz crystal input or 32-kHz crystal input or external
clock input or external trimming resistor input
OSC2
O
Oscillator output
4-MHz crystal output or 32-kHz crystal output or
external clock input
ATAM893-D
4680C–4BMCU–01/05
ATAM893-D
2. Introduction
The ATAM893-D is a member of Atmel’s family of 4-bit single-chip microcontrollers. Instead of
ROM it contains EEPROM, RAM, parallel I/O ports, two 8-bit programmable multifunction
timer/counters, voltage supervisor, interval timer with watchdog function and a sophisticated onchip clock generation with integrated RC-, 32-kHz and 4-MHz crystal oscillators.
3. Differences Between ATAM893-D and ATARx90/x92
3.1
Program Memory
The program memory of the MTP device is realized as an EEPROM. The memory size for user
programs is 4096 bytes. It is programmed as 258 × 16-byte blocks of data. The implemented
LOCK bit function is user selectable and protects the device from unauthorized read out of the
program memory.
3.2
Configuration Memory
An additional area of 32 bytes of the EEPROM is used to store information about the hardware
configuration. All the options that are selectable for the ROM versions are available to the user.
This includes not only the different port options but also the possibilities to select different capacitors for OSC1 and OSC2, the option to enable or disable the hardlock for the watchdog, the
option to select OSC2 instead of OSC1 as external clock input and the option to enable the
external clock monitor as a reset source. Activating the options is performed by the reset circuitry. Reset starts a download sequence to transfer the information from the memory into a shift
register (configuration register).
3.3
Data Memory
The ATAM893-D contains an internal data EEPROM that is organized as two pages of
32 × 16 bit. If it is necessary to be compatible with the ROM parts, only one page must be used
with the flash part. Also for compatibility reasons the access to the EEPROM is handled via the
MCL (serial interface) as in the corresponding ROM parts. A behavioral difference that only
needs to be considered for error handling can be seen, when the communication via the MCL is
not terminated correctly. A missing STOP condition leads to a significantly higher current consumption for the ROM parts compared to the flash parts. A slightly different concept for the read
amplifiers of the memory makes the flash part more tolerant in terms of communication errors.
3.4
Reset Function
During each reset (power-on or brown-out) the configuration register is reset and reloaded with
the data from the configuration memory. This leads to a slightly different behavior compared to
the ROM versions. Both devices switch their I/Os to input during reset but the ROM part has the
mask selected pull-up or pull-down resistors active while the MTP has them removed until the
download is finished.
3
4680C–4BMCU–01/05
3.5
RC-oscillator Frequency
The typical frequency of the internal RC-oscillator is about 5% higher for the Flash part compared to the ROM part. But due to the wide range of ±50% overall tolerances this should not
affect the application too much.
This 5% is also valid for the RC-oscillator with an external resistor. For a frequency of 4 MHz the
flash part requires a resistor of 180 k, while the ROM part only needs 170 k.
3.6
High Drive Outputs
On request the ROM parts offer a high current output selection. These pins than are twice as
strong as in the standard configuration. The ATAM893-D does not offer this selection. Only the
Timer 2 output (BP42) and the Timer 3 output (BP60) are configured as high current outputs for
the low side driver by default. This configuration is fixed and cannot be changed by the
customer.
4. MARC4 Architecture
4.1
General Description
The MARC4 microcontroller consists of an advanced stack-based, 4-bit CPU core and on-chip
peripherals. The CPU is based on the Harvard architecture with physically separate program
memory (ROM) and data memory (RAM). Three independent buses, the instruction bus, the
memory bus and the I/O bus, are used for parallel communication between ROM, RAM and
peripherals. This enhances program execution speed by allowing both instruction prefetching,
and a simultaneous communication to the on-chip peripheral circuitry. The extremely powerful
integrated interrupt controller with associated eight prioritized interrupt levels supports fast and
efficient processing of hardware events. The MARC4 is designed for the high-level programming
language qFORTH. The core includes both, an expression and a return stack. This architecture
enables high-level language programming without any loss of efficiency or code density.
Figure 4-1.
MARC4 Core
MARC4 CORE
Reset
Program
memory
Reset
Clock
PC
Instruction
bus
X
Y
SP
RP
Memory bus
Instruction
decoder
System
clock
Sleep
RAM
256 x 4-bit
TOS
CCR
Interrupt
controller
ALU
I/O bus
On-chip peripheral modules
4
ATAM893-D
4680C–4BMCU–01/05
ATAM893-D
4.2
Components of MARC4 Core
The core contains ROM, RAM, ALU, program counter, RAM address registers, instruction
decoder and interrupt controller. The following sections describe each functional block in more
detail.
4.2.1
Program Memory
The program memory (EEPROM) is programmable with the customer application program. The
EEPROM is addressed by a 12-bit wide program counter, thus predefining a maximum program
bank size of 4 Kbytes. The lowest user program memory address segment is taken up by a 512byte zero page which contains predefined start addresses for interrupt service routines and special subroutines accessible with single byte instructions (SCALL).
The corresponding memory map is shown in Figure 4-2. Look-up tables of constants can 0also
be held in ROM and are accessed via the MARC4’s built-in table instruction.
ROM Map
1F8h
1F0h
1E8h
1E0h
FFFh
EEPROM
(4 K x 8 bit)
7FFh
1FFh
Zero page
000h
4.2.2
SCALL addresses
Figure 4-2.
020h
018h
010h
008h
000h
page
1E0h
INT7
1C 0h
INT6
180h
INT5
140h
INT4
100h
INT3
0C 0h
INT2
080h
INT1
040h
INT0
008h
000h
$AUTOSLEEP
$RESET
RAM
The ATAM893-D contains 256 × 4-bit wide static random access memory (RAM). It is used for
the expression stack, the return stack and data memory for variables and arrays. The RAM is
addressed by any of the four 8-bit wide RAM address registers SP, RP, X and Y.
4.2.2.1
Expression Stack
The 4-bit wide expression stack is addressed with the expression Stack Pointer (SP). All arithmetic, I/O and memory reference operations take their operands from, and return their results to
the expression stack. The MARC4 performs the operations with the top of stack items (TOS and
TOS-1). The TOS register contains the top element of the expression stack and works in the
same way as an accumulator. This stack is also used for passing parameters between subroutines and as a scratch pad area for temporary storage of data.
5
4680C–4BMCU–01/05
4.2.2.2
Return Stack
The 12-bit wide return stack is addressed by the Return stack Pointer (RP). It is used for storing
return addresses of subroutines, interrupt routines and for keeping loop index counts. The return
stack can also be used as a temporary storage area.
The MARC4 instruction set supports the exchange of data between the top elements of the
expression stack and the return stack. The two stacks within the RAM have a user definable
location and maximum depth.
Figure 4-3.
RAM Map
RAM
(256 x 4-bit)
Autosleep
RAM address register:
FCh
Expression stack
3
Global
variables
X
SP
4-bit
Y
SP
TOS-1
Expression
stack
Return stack
11
0
RP
Return
stack
RP
04h
00h
4.2.3
0
TOS
TOS-1
TOS-2
FFh
07h
03h
Global
variables
12-bit
Registers
The MARC4 controller has seven programmable registers and one condition code register. They
are shown in the following programming model.
4.2.3.1
6
Program Counter (PC)
The program counter is a 12-bit register which contains the address of the next instruction to be
fetched from the ROM. Instructions currently being executed are decoded in the instruction
decoder to determine the internal micro-operations. For linear code (no calls or branches) the
program counter is incremented with every instruction cycle. If a branch-, call-, return-instruction
or an interrupt is executed, the program counter is loaded with a new address. The program
counter is also used with the table instruction to fetch 8-bit wide ROM constants.
ATAM893-D
4680C–4BMCU–01/05
ATAM893-D
Figure 4-4.
Programming Model
11
0
PC
Program counter
0
7
0
RP
7
0
Return stack pointer
0
SP
Expression stack pointer
0
7
X
RAM address register (X)
7
0
Y
RAM address register (Y)
3
0
3
C
0
I
Top of stack register
TOS
CCR
--
B
Condition code register
Interrupt enable
Branch
Reserved
Carry/borrow
4.2.3.2
RAM Address Registers
The RAM is addressed with the four 8-bit wide RAM address registers: SP, RP, X and Y. These
registers allow access to any of the 256 RAM nibbles.
4.2.3.3
Expression Stack Pointer (SP)
The stack pointer contains the address of the next-to-top 4-bit item (TOS-1) of the expression
stack. The pointer is automatically pre-incremented if a nibble is moved onto the stack or postdecremented if a nibble is removed from the stack. Every post-decrement operation moves the
item (TOS-1) to the TOS register before the SP is decremented. After a reset the stack pointer
has to be initialized with “>SP S0” to allocate the start address of the expression stack area.
4.2.3.4
Return Stack Pointer (RP)
The return stack pointer points to the top element of the 12-bit wide return stack. The pointer
automatically pre-increments if an element is moved onto the stack, or it post-decrements if an
element is removed from the stack. The return stack pointer increments and decrements in
steps of 4. This means that every time a 12-bit element is stacked, a 4-bit RAM location is left
unwritten. This location is used by the qFORTH compiler to allocate 4-bit variables. After a reset
the return stack pointer has to be initialized via “>RP FCh”.
4.2.3.5
RAM Address Registers (X and Y)
The X and Y registers are used to address any 4-bit item in the RAM. A fetch operation moves
the addressed nibble onto the TOS. A store operation moves the TOS to the addressed RAM
location. By using either the pre-increment or post-decrement addressing mode, arrays in the
RAM can be compared, filled or moved.
7
4680C–4BMCU–01/05
4.2.3.6
Top Of Stack (TOS)
The top of stack register is the accumulator of the MARC4. All arithmetic/logic, memory reference and I/O operations use this register. The TOS register receives data from the ALU, ROM,
RAM or I/O bus.
4.2.3.7
Condition Code Register (CCR)
The 4-bit wide condition code register contains the branch, the carry and the interrupt enable
flag. These bits indicate the current state of the CPU. The CCR flags are set or reset by ALU
operations. The instructions SET_BCF, TOG_BF, CCR! and DI allow direct manipulation of the
condition code register.
4.2.3.8
Carry/Borrow (C)
The carry/borrow flag indicates that the borrowing or carrying out of Arithmetic Logic Unit (ALU)
occurred during the last arithmetic operation. During shift and rotate operations, this bit is used
as a fifth bit. Boolean operations have no affect on the C-flag.
4.2.3.9
Branch (B)
The branch flag controls the conditional program branching. Should the branch flag have been
set by a previous instruction, a conditional branch will cause a jump. This flag is affected by
arithmetic, logic, shift, and rotate operations.
4.2.3.10
4.2.4
Interrupt Enable (I)
The interrupt enable flag globally enables or disables the triggering of all interrupt routines with
the exception of the non-maskable reset. After a reset or on executing the DI instruction, the
interrupt enable flag is reset, thus disabling all interrupts. The core will not accept any further
interrupt requests until the interrupt enable flag has been set again by either executing an EI,
RTI or SLEEP instruction.
ALU
The 4-bit ALU performs all the arithmetic, logical, shift and rotate operations with the top two elements of the expression stack (TOS and TOS-1) and returns the result to the TOS. The ALU
operations affect the carry/borrow and branch flag in the condition code register (CCR).
Figure 4-5.
ALU Zero-address Operations
RAM
SP
TOS-1
TOS
TOS-2
TOS-3
TOS-4
ALU
CCR
8
ATAM893-D
4680C–4BMCU–01/05
ATAM893-D
4.2.5
I/O Bus
The I/O ports and the registers of the peripheral modules are I/O mapped. All communication
between the core and the on-chip peripherals takes place via the I/O bus and the associated I/O
control. With the MARC4 IN and OUT instructions the I/O bus allows a direct read or write
access to one of the 16 primary I/O addresses. More about the I/O access to the on-chip peripherals is described in the section “Peripheral Modules”. The I/O bus is internal and is not
accessible by the customer on the final microcontroller device, but it is used as the interface for
the MARC4 emulation (see section “Emulation”).
4.2.6
Instruction Set
The MARC4 instruction set is optimized for the high level programming language qFORTH.
Many MARC4 instructions are qFORTH words. This enables the compiler to generate a fast and
compact program code. The CPU has an instruction pipeline allowing the controller to prefetch
an instruction from program memory at the same time as the present instruction is being executed. The MARC4 is a zero address machine, the instructions containing only the operation to
be performed and no source or destination address fields. The operations are implicitly performed on the data placed on the stack. There are one and two byte instructions which are
executed within 1 to 4 machine cycles. A MARC4 machine cycle is made up of two system clock
cycles (SYSCL). Most of the instructions are only one byte long and are executed in a single
machine cycle. For more information refer to the “MARC4 Programmer's Guide”.
4.2.7
4.2.7.1
Interrupt Structure
The MARC4 can handle interrupts with eight different priority levels. They can be generated
from the internal and external interrupt sources or by a software interrupt from the CPU itself.
Each interrupt level has a hard-wired priority and an associated vector for the service routine in
the program memory (see Table 4-2 on page 11). The programmer can postpone the processing
of interrupts by resetting the interrupt enable flag (I) in the CCR. An interrupt occurrence will still
be registered, but the interrupt routine only started after the I flag is set. All interrupts can be
masked, and the priority individually software configured by programming the appropriate control
register of the interrupting module (see section “Peripheral Modules”).
Interrupt Processing
For processing the eight interrupt levels, the MARC4 includes an interrupt controller with two
8-bit wide “interrupt pending” and “interrupt active” registers. The interrupt controller samples all
interrupt requests during every non-I/O instruction cycle and latches these in the interrupt pending register. If no higher priority interrupt is present in the interrupt active register, it signals the
CPU to interrupt the current program execution. If the interrupt enable bit is set, the processor
enters an interrupt acknowledge cycle. During this cycle a short call (SCALL) instruction to the
service routine is executed and the current PC is saved on the return stack.
An interrupt service routine is completed with the RTI instruction. This instruction resets the corresponding bits in the interrupt pending/active register and fetches the return address from the
return stack to the program counter. When the interrupt enable flag is reset (triggering of interrupt routines are disabled), the execution of new interrupt service routines is inhibited but not the
logging of the interrupt requests in the interrupt pending register. The execution of the interrupt
is delayed until the interrupt enable flag is set again. Note that interrupts are only lost if an interrupt request occurs while the corresponding bit in the pending register is still set (i.e., the
interrupt service routine is not yet finished).
9
4680C–4BMCU–01/05
4.2.7.2
Interrupt Latency
The interrupt latency is the time from the occurrence of the interrupt to the interrupt service routine being activated. In MARC4 this is extremely short (taking between 3 to 5 machine cycles
depending on the state of the core).
Figure 4-6.
Interrupt Handling
INT7
7
INT7 active
Priority Level
RTI
INT5
6
5
INT5 active
RTI
INT3
4
INT2
3
INT3 active
RTI
2
INT2 pending
1
SWI0
INT2 active
RTI
0
INT0 pending
INT0 active
RTI
Main/
Autosleep
Main/
Autosleep
Time
Table 4-1.
10
Interrupt Priority Table
Interrupt
Priority
ROM Address
Interrupt Opcode
Function
INT0
Lowest
040h
C8h (SCALL 040h)
Software interrupt (SWI0)
INT1
|
080h
D0h (SCALL 080h)
External hardware interrupt, any edge at BP52 or
BP53
INT2
|
0C0h
D8h (SCALL 0C0h)
Timer 1 interrupt
INT3
|
100h
E8h (SCALL 100h)
SSI interrupt or external hardware interrupt at BP40 or
BP43
INT4
|
140h
E8h (SCALL 140h)
Timer 2 interrupt
INT5
|
180h
F0h (SCALL 180h)
Timer 3 interrupt
INT6
Ø
1C0h
F8h (SCALL 1C0h)
External hardware interrupt, at any edge at BP50 or
BP51
INT7
Highest
1E0h
FCh (SCALL 1E0h)
Voltage Monitor (VM) interrupt
ATAM893-D
4680C–4BMCU–01/05
ATAM893-D
Table 4-2.
Hardware Interrupts
Interrupt Mask
Interrupt
Register
Bit
Interrupt Source
INT1
P5CR
P52M1, P52M2
P53M1, P53M2
Any edge at BP52
Any edge at BP53
INT2
T1M
T1IM
Timer 1
INT3
SISC
SIM
SSI buffer full/empty or BP40/BP43 interrupt
INT4
T2CM
T2IM
Timer 2 compare match/overflow
INT5
T3CM1
T3CM2
T3C
T3IM1
T3IM2
T3EIM
Timer 3 compare register 1 match
Timer 3 compare register 2 match
Timer 3 edge event occurs (T3I)
INT6
P5CR
P50M1, P50M2
P51M1, P51M2
INT7
VCM
VIM
Any edge at BP50
Any edge at BP51
External/internal voltage monitoring
4.2.7.3
Software Interrupts
The programmer can generate interrupts by using the Software Interrupt Instruction (SWI) which
is supported in qFORTH by predefined macros named SWI0...SWI7. The software triggered
interrupt operates exactly like any hardware triggered interrupt. The SWI instruction takes the
top two elements from the expression stack and writes the corresponding bits via the I/O bus to
the interrupt pending register. Therefore, by using the SWI instruction, interrupts can be re-prioritized or lower priority processes scheduled for later execution.
4.2.7.4
Hardware Interrupts
In the ATAM893-D, there are eleven hardware interrupt sources with seven different levels.
Each source can be masked individually by mask bits in the corresponding control registers. An
overview of the possible hardware configurations is shown in Table 4-2.
4.3
Master Reset
The master reset forces the CPU into a well-defined condition. It is unmaskable and is activated
independent of the current program state. It can be triggered by either initial supply power-up, a
short collapse of the power supply, brown-out detection circuitry, watchdog time-out, or an external input clock supervisor stage (see Figure 4-7 on page 12).
A master reset activation will reset the interrupt enable flag, the interrupt pending register and
the interrupt active register. During the power-on reset phase the I/O bus control signals are set
to reset mode thereby initializing all on-chip peripherals. All bi-directional ports are set to input
mode.
Attention: During any reset phase, the BP20/NTE input is driven towards VDD by a strong pullup transistor. This pin must not be pulled down to VSS during reset by any external circuitry representing a resistor of less than 150 kΩ.
Releasing the reset results in a short call instruction (opcode C1h) to the EEPROM address
008h. This activates the initialization routine $RESET which in turn has to initialize all necessary
RAM variables, stack pointers and peripheral configuration registers (see Table 5-1 on page 23).
11
4680C–4BMCU–01/05
Figure 4-7.
Reset Configuration
VDD
Pull-up
CL
NRST
res
Reset
timer
Internal
reset
CL = SYSCL/4
4.3.1
Power-on
reset
VDD
Brown-out
detection
VDD
VSS
VSS
Watchres
dog
CWD
Ext. clock
supervisor
ExIn
Power-on Reset and Brown-out Detection
The ATAM893-D has a fully integrated power-on reset and brown-out detection circuitry. For
reset generation no external components are needed.
These circuits ensure that the core is held in the reset state until the minimum operating supply
voltage has been reached. A reset condition will also be generated should the supply voltage
drop momentarily below the minimum operating level except when a power down mode is activated (the core is in SLEEP mode and the peripheral clock is stopped). In this power-down
mode the brown-out detection is disabled. Two values for the brown-out voltage threshold are
programmable via the BOT bit in the SC register.
A power-on reset pulse is generated by a VDD rise across the default BOT voltage level (1.7 V).
A brown-out reset pulse is generated when VDD falls below the brown-out voltage threshold. Two
values for the brown-out voltage threshold are programmable via the BOT bit in the SC register.
When the controller runs in the upper supply voltage range with a high system clock frequency,
the high threshold must be used. When it runs with a lower system clock frequency, the low
threshold and a wider supply voltage range may be chosen. For further details, see the electrical
specification and the SC register description for BOT programming.
12
ATAM893-D
4680C–4BMCU–01/05
ATAM893-D
Figure 4-8.
Brown-out Detection
VDD
2.0 V
1.7 V
td
CPU
Reset
BOT = 1
td
CPU
Reset
t
td
BOT = 0
td = 1.5 ms (typically)
BOT = 1, low brown-out voltage threshold 1.7 V (is reset value).
BOT = 0, high brown-out voltage threshold 2.0 V.
4.3.2
Watchdog Reset
The watchdog's function can be enabled at the WDC register and triggers a reset with every
watchdog counter overflow. To suppress the watchdog reset, the watchdog counter must be
regularly reset by reading the watchdog register address (CWD). The CPU reacts in exactly the
same manner as a reset stimulus from any of the above sources.
4.3.3
External Clock Supervisor
The external input clock supervisor function can be enabled if the external input clock is selected
within the CM and SC registers of the clock module. The CPU reacts in exactly the same manner as a reset stimulus from any of the above sources.
4.4
Voltage Monitor
The voltage monitor consists of a comparator with an internal voltage reference. It is used to
supervise the supply voltage or an external voltage at the VMI pin. The comparator for the supply voltage has three internal programmable thresholds: one lower threshold (2.2 V), one middle
threshold (2.6 V) and one higher threshold (3.0 V). For external voltages at the VMI pin, the
comparator threshold is set to VBG = 1.3 V. The VMS bit indicates if the supervised voltage is
below (VMS = 0) or above (VMS = 1) this threshold. An interrupt can be generated when the
VMS bit is set or reset to detect a rising or falling slope. A voltage monitor interrupt (INT7) is
enabled when the interrupt mask bit (VIM) is reset in the VMC register.
13
4680C–4BMCU–01/05
Figure 4-9.
Voltage Monitor
VDD
Voltage monitor
IN
VMC
VM2
VM1 VM0
-
VMST
4.4.1
INT7
OUT
BP41/
VMI
-
VIM
res VMS
Voltage Monitor Control/Status Register
Primary register address: ’F’hex
Bit 3
Bit 2
Bit 1
Bit 0
VMC: Write
VM2
VM1
VM0
VIM
Reset value: 1111b
VMST: Read
–
–
reserved
VMS
Reset value: xx11b
VM2: Voltage monitor Mode bit 2
VM1: Voltage monitor Mode bit 1
VM0: Voltage monitor Mode bit 0
Table 4-3.
14
Voltage Monitor Modes
VM2
VM1
VM0
1
1
1
Disable voltage monitor
Function
1
1
0
External (VIM input), internal reference threshold (1.3 V), interrupt
with negative slope
1
0
1
Not allowed
1
0
0
External (VMI input), internal reference threshold (1.3 V), interrupt
with positive slope
0
1
1
Internal (supply voltage), high threshold (3.0 V), interrupt with
negative slope
0
1
0
Internal (supply voltage), middle threshold (2.6 V), interrupt with
negative slope
0
0
1
Internal (supply voltage), low threshold (2.2 V), interrupt with
negative slope
0
0
0
Not allowed
ATAM893-D
4680C–4BMCU–01/05
ATAM893-D
VIM
Voltage Interrupt Mask bit
VIM = 0, voltage monitor interrupt is enabled
VIM = 1, voltage monitor interrupt is disabled
VMS
Voltage Monitor Status bit
VMS = 0, the voltage at the comparator input is below VRef
VMS = 1, the voltage at the comparator input is above VRef
Figure 4-10. Internal Supply Voltage Supervisor
VMS = 1
VDD
Low threshold
Middle threshold
High threshold
3.0 V
2.6 V
2.2 V
Low threshold
Middle threshold
High threshold
VMS = 0
Figure 4-11. External Input Voltage Supervisor
Internal reference level
VMI
Negative slope
Interrupt positive slope
VMS = 1
VMS = 1
VMS = 0
VMS = 0
1.3 V
Positive slope
Interrupt negative slope
4.5
4.5.1
t
Clock Generation
Clock Module
The ATAM893-D contains a clock module with 4 different internal oscillator types: two RC-oscillators, one 4-MHz crystal oscillator and one 32-kHz crystal oscillator. The pins OSC1 and OSC2
are the interface to connect a crystal either to the 4-MHz, or to the 32-kHz crystal oscillator.
OSC1 can be used as input for external clocks or to connect an external trimming resistor for the
RC-oscillator 2. All necessary circuitry except the crystal and the trimming resistor is integrated
on-chip. One of these oscillator types or an external input clock can be selected to generate the
system clock (SYSCL).
In applications that do not require exact timing, it is possible to use the fully integrated RC-oscillator 1 without any external components. The RC-oscillator 1 center frequency tolerance is
better than ±50%. The RC-oscillator 2 is a trimmable oscillator whereby the oscillator frequency
can be trimmed with an external resistor attached between OSC1 and VDD. In this configuration,
the RC-oscillator 2 frequency can be maintained stable to within a tolerance of ±15% over the
full operating temperature and voltage range.
15
4680C–4BMCU–01/05
The clock module is programmable via software with the clock management register (CM) and
the system configuration register (SC). The required oscillator configuration can be selected with
the OS1 bit and the OS0 bit in the SC register. A programmable 4-bit divider stage allows the
adjustment of the system clock speed. A special feature of the clock management is that an
external oscillator may be used and switched on and off via a port pin for the power-down mode.
Before the external clock is switched off, the internal RC-oscillator 1 must be selected with the
CCS bit and then the SLEEP mode may be activated. In this state an interrupt can wake up the
controller with the RC-oscillator, and the external oscillator can be activated and selected by
software. A synchronization stage avoids clock periods that are too short if the clock source or
the clock speed is changed. If an external input clock is selected, a supervisor circuit monitors
the external input and generates a hardware reset if the external clock source fails or drops
below 500 kHz for more than 1 ms.
Figure 4-12. Clock Module
RCoscillator 1
Ext. clock
OSC1
Oscin
ExOut
Stop
ExIn
*
RCOut1
Stop Control
RC oscillator 2
RCOut2
Stop
RTrim
SYSCL
IN1
Cin
/2
/2
/2
/2
IN2
4-MHz oscillator
Divider
4Out
Oscin
Oscout
Stop
32-kHz oscillator
OSC2
Oscout
*
Oscin
Oscout
32Out
Osc-Stop
CM
Sleep
WDL
Cin/16
NSTOP
CCS
CSS1
SUBCL
CSS0
32 kHz
*
configurable
SC
BOT
---
Table 4-4.
OS1
OS0
Clock Modes
Clock Source for SYSCL
Mode
OS1
OS0
CCS = 1
CCS = 0
Clock Source for
SUBCL
1
1
1
RC-oscillator 1 (intern)
External input clock
Cin/16
2
0
1
RC-oscillator 1 (intern)
RC-oscillator 2 with external
trimming resistor
Cin/16
3
1
0
RC-oscillator 1 (intern)
4-MHz oscillator
Cin/16
4
0
0
RC-oscillator 1 (intern)
32-kHz oscillator
32 kHz
The clock module generates two output clocks. One is the system clock (SYSCL) and the other
the periphery (SUBCL). The SYSCL can supply the core and the peripherals and the SUBCL
can supply only the peripherals with clocks. The modes for clock sources are programmable
with the OS1 bit and OS0 bit in the SC register and the CCS bit in the CM register.
16
ATAM893-D
4680C–4BMCU–01/05
ATAM893-D
4.5.2
4.5.2.1
Oscillator Circuits and External Clock Input Stage
The ATAM893-D series consists of four different internal oscillators: two RC-oscillators, one 4MHz crystal oscillator, one 32-kHz crystal oscillator and one external clock input stage.
RC-oscillator 1 Fully Integrated
For timing insensitive applications, it is possible to use the fully integrated RC-oscillator 1. It
operates without any external components and saves additional costs. The RC-oscillator 1 center frequency tolerance is better than ±50% over the full temperature and voltage range. The
basic center frequency of the RC-oscillator 1 is fO ≈ 4.0 MHz. The RC oscillator 1 is selected by
default after power-on reset.
Figure 4-13. RC-oscillator 1
RC-oscillator 1
RcOut1
RcOut1
Osc-Stop
Stop
Control
4.5.2.2
External Input Clock
The OSC1 or OSC2 can be driven by an external clock source provided it meets the specified
duty cycle, rise and fall times and input levels. Additionally, the external clock stage contains a
supervisory circuit for the input clock. The supervisor function is controlled via the OS1, OS0 bit
in the SC register and the CCS bit in the CM register. If the external input clock is missing for
more than 1 ms and CCS = 0 is set in the CM register, the supervisory circuit generates a hardware reset.
Figure 4-14. External Input Clock
Ext. input clock
Ext.
Clock
ExOut
OSC1
ExIn
Stop
or
Ext.
Clock
RcOut1
Osc-Stop
CCS
OSC2
Clock monitor
Res
17
4680C–4BMCU–01/05
Table 4-5.
4.5.2.3
Supervisor Function Control Bits
OS1
OS0
CCS
Supervisor Reset Output (Res)
1
1
0
Enable
1
1
1
Disable
x
0
x
Disable
RC-oscillator 2 with External Trimming Resistor
The RC-oscillator 2 is a high resolution trimmable oscillator whereby the oscillator frequency can
be trimmed with an external resistor between OSC1 and VDD. In this configuration, the RC-oscillator 2 frequency can be maintained stable with a tolerance of ±15%/-20% over the full operating
temperature and a voltage range VDD from 2.5 V to 6.0 V.
For example: An output frequency at the RC-oscillator 2 of 2 MHz can be obtained by connecting a resistor Rext = 360 kΩ (see Figure 4-15).
Figure 4-15. RC-oscillator 2
VDD
RC-oscillator 2
Rext
OSC1
RcOut2
RTrim
Stop
RcOut2
Osc-Stop
OSC2
4.5.2.4
4-MHz Oscillator
The ATAM893-D 4-MHz oscillator options need a crystal or ceramic resonator connected to the
OSC1 and OSC2 pins to establish oscillation. All the necessary oscillator circuitry, with the
exception of the actual crystal, resonator, C3 and C4 are integrated on-chip.
Figure 4-16. 4-MHz Crystal Oscillator
OSC1
Oscin
4Out
*
XTAL
4 MHz
C1
4-MHz
oscillator
Oscout
OSC2
Stop
4Out
Osc-Stop
*
*
C2
flash option
Note:
18
Both, the 4-MHz and the 32-kHz crystal oscillator, use an integrated 14 stage divider circuit to stabilize oscillation before the oscillator output is used as system clock. This results in an additional
delay of about 4 ms for the 4-MHz crystal and about 500 ms for the 32-kHz crystal.
ATAM893-D
4680C–4BMCU–01/05
ATAM893-D
Figure 4-17. Ceramic Resonator
C3
OSC1
Oscin
4Out
*
Cer.
Res
4-MHz
oscillator
C1
Oscout
OSC2
C4
Stop
4Out
Osc-Stop
*
*
C2
flash option
Note:
4.5.2.5
Both, the 4-MHz and the 32-kHz crystal oscillator, use an integrated 14 stage divider circuit to stabilize oscillation before the oscillator output is used as system clock. This results in an additional
delay of about 4 ms for the 4-MHz crystal and about 500 ms for the 32-kHz crystal.
32-kHz Oscillator
Some applications require long-term time keeping or low resolution timing. In this case, an onchip, low power 32-kHz crystal oscillator can be used to generate both the SUBCL and the
SYSCL. In this mode, power consumption is greatly reduced. The 32-kHz crystal oscillator can
not be stopped while the power-down mode is in operation.
Figure 4-18. 32-kHz Crystal Oscillator
OSC1
Oscin
32Out
*
XTAL
32 kHz
C1
32Out
32-kHz
oscillator
Oscout
OSC2
*
*
C2
flash option
Note:
4.5.3
Both, the 4-MHz and the 32-kHz crystal oscillator, use an integrated 14 stage divider circuit to stabilize oscillation before the oscillator output is used as system clock. This results in an additional
delay of about 4 ms for the 4-MHz crystal and about 500 ms for the 32-kHz crystal.
Clock Management
The clock management register controls the system clock divider and synchronization stage.
Writing to this register triggers the synchronization cycle.
19
4680C–4BMCU–01/05
4.5.3.1
Clock Management Register (CM)
Auxiliary register address: '3'hex
CM:
Bit 2
Bit 1
Bit 0
NSTOP
CCS
CSS1
CSS0
Reset value: 1111b
NSTOP
Not STOP peripheral clock
NSTOP = 0, stops the peripheral clock while the core is in SLEEP mode
NSTOP = 1, enables the peripheral clock while the core is in SLEEP mode
CCS
Core Clock Select
CCS = 1, the internal RC-oscillator 1 generates SYSCL
CCS = 0, the 4-MHz crystal oscillator, the 32-kHz crystal oscillator, an external
clock source or the RC-oscillator 2 with the external resistor at OSC1
generates SYSCL dependent on the setting of OS0 and OS1 in the
system configuration register
CSS1
Core Speed Select 1
CSS0
Core Speed Select 0
Table 4-6.
4.5.3.2
Bit 3
Core Speed Select
CSS1
CSS0
Divider
0
0
16
1
1
8
1
0
4
0
1
2
Note
Reset value
System Configuration Register (SC)
Primary register address: '3'hex
20
Bit 3
Bit 2
Bit 1
Bit 0
SC: write
BOT
–
OS1
OS0
BOT
Brown-Out Threshold
BOT = 1, low brown-out voltage threshold (1.65 V)
BOT = 0, high brown-out voltage threshold (1.95 V)
OS1
Oscillator Select 1
OS0
Oscillator Select 0
Reset value: 1x11b
ATAM893-D
4680C–4BMCU–01/05
ATAM893-D
Table 4-7.
Mode
OS1
OS0
Input for SUBCL
1
1
1
Cin/16
RC-oscillator 1 and external input clock
2
0
1
Cin/16
RC-oscillator 1 and RC-oscillator 2
3
1
0
Cin/16
RC-oscillator 1 and 4-MHz crystal oscillator
4
0
0
32 kHz
RC-oscillator 1 and 32-kHz crystal oscillator
Note:
4.6
Oscillator Select
Selected Oscillators
If the bit CCS = 0 in the CM-register the RC-oscillator 1 always stops
Power-down Modes
The sleep mode is a shut-down condition which is used to reduce the average system power
consumption in applications where the microcontroller is not fully utilized. In this mode, the system clock is stopped. The sleep mode is entered via the SLEEP instruction. This instruction sets
the interrupt enable bit (I) in the condition code register to enable all interrupts and stops the
core. During the sleep mode the peripheral modules remain active and are able to generate
interrupts. The microcontroller exits the sleep mode by carrying out any interrupt or a reset.
The sleep mode can only be kept when none of the interrupt pending or active register bits are
set. The application of the $AUTOSLEEP routine ensures the correct function of the sleep
mode. For standard applications use the $AUTOSLEEP routine to enter the power-down mode.
Using the SLEEP instruction instead of the $AUTOSLEEP following an I/O instruction requires
the insertion of 3 non I/O instruction cycles (for example NOP NOP NOP) between the IN or
OUT command and the SLEEP command.
The total power consumption is directly proportional to the active time of the microcontroller. For
a rough estimation of the expected average system current consumption, the following formula
should be used:
t active
I total ( V DD ,f syscl ) = ISleep + ⎛ I DD × --------------⎞ IDD depends on VDD and fsyscl
⎝
t total ⎠
The ATAM893-D has various power-down modes. During the sleep mode the clock for the
MARC4 core is stopped. With the NSTOP bit in the clock management register (CM) it is programmable if the clock for the on-chip peripherals is active or stopped during the sleep mode. If
the clock for the core and the peripherals is stopped the selected oscillator is switched off. An
exception is the 32-kHz oscillator, if it is selected it runs continuously independent of the NSTOP
bit. If the oscillator is stopped or the 32-kHz oscillator is selected, power consumption is
extremely low.
Table 4-8.
Power-down Modes
Brown-out
Function
RC-Oscillator 1
RC-Oscillator 2
4-MHz Oscillator
32-kHz
Oscillator
External
Input Clock
Mode
CPU Core
OscStop(1)
Active
RUN
NO
Active
RUN
RUN
YES
Power-down
SLEEP
NO
Active
RUN
RUN
YES
STOP
RUN
STOP
SLEEP
SLEEP
YES
STOP
Note:
Osc-Stop = SLEEP and NSTOP and WDL
21
4680C–4BMCU–01/05
5. Peripheral Modules
5.1
Addressing Peripherals
Accessing the peripheral modules takes place via the I/O bus (see Figure 5-1). The IN or OUT
instructions allow direct addressing of up to 16 I/O modules. A dual register addressing scheme
has been adopted to enable direct addressing of the primary register. To address the auxiliary
register, the access must be switched with an auxiliary switching module. Thus, a single IN (or
OUT) to the module address will read (or write into) the module primary register. Accessing the
auxiliary register is performed with the same instruction preceded by writing the module address
into the auxiliary switching module. Byte wide registers are accessed by multiple IN- (or OUT-)
instructions. For more complex peripheral modules, with a larger number of registers, extended
addressing is used. In this case a bank of up to 16 subport registers are indirectly addressed
with the subport address. The first OUT-instruction writes the subport address to the subaddress
register, the second IN- or OUT-instruction reads data from or writes data to the addressed
subport.
Figure 5-1.
Example of I/O Addressing
Module M1
Module ASW
(Address Pointer)
Subaddress Reg.
Module M2
Bank of
Primary Regs.
Auxiliary Switch
Module
Subport FH
1
Module M3
Aux. Reg.
5
Subport EH
Subport 1
Primary Reg.
Primary Reg.
Primary Reg.
Subport 0
2
3
6
4
I/O bus
to other modules
Indirect Subport Access
Dual Register Access
(Primary Register Write)
(Subport Register Write)
1
Addr. (SPort) Addr. (M1) OUT
2
SPort_Data
Addr. (M1)
1
Example of
qFORTH
Program
Code
Addr. (SPort) Addr. (M1) OUT
Prim._Data Addr. (M2) OUT
4
Addr. (M2) Addr. (ASW) OUT
5
Aux._Data Addr. (M2) OUT
6
(Auxiliary Register Write)
Addr. (M1) IN
Prim._Data Addr. (M3) OUT
(Primary Register Read)
6
Addr. (M3) IN
(Primary Register Read)
3
(Subport Register Write Byte)
1
Addr. (SPort) Addr. (M1) OUT
2
SPort_Data (lo) Addr. (M1)
OUT
2
SPort_Data (hi) Addr. (M1)
OUT
Addr. (M2) IN
(Auxiliary Register Read )
4
5
(Subport Register Read Byte)
1
(Primary Register Write)
3
OUT
(Subport Register Read)
2
Single Register Access
Addr. (SPort) Addr. (M1) OUT
Addr. (M2) Addr. (ASW) OUT
Addr. (M2) IN
(Auxiliary Register Write Byte)
4
Addr. (M2) Addr. (ASW) OUT
2
Addr. (M1) IN (hi)
5
Aux._Data (lo) Addr. (M2)
OUT
2
Addr. (M1) IN (lo)
5
Aux._Data (hi) Addr. (M2)
OUT
Addr. (ASW) = Auxililiary Switch Module Address
Addr. (Mx) = Module Mx Address
Addr. (SPort) = Subport Address
Prim._Data = Data to be written into Primary Register
Aux._Data = Data to be written into Auxiliary Register
Aux._Data (hi) = Data to be written into Auxiliary Register (high nibble)
SPort_Data (lo) = Data to be written into Subport (low nibble)
SPort_Data (hi) = Data to be written into Subport (high nibble)
(lo) = SPort_Data (low nibble)
(hi) = SPort_Data (high nibble)
Aux._Data (lo) = Data to be written into Auxiliary Register (low nibble)
22
ATAM893-D
4680C–4BMCU–01/05
ATAM893-D
Table 5-1.
Peripheral Addresses
Port Address
See
Page
Port 1 - data register/input data
M3
24
Port 2 - data register/pin data
M2
26
Write/Read
1
P1DAT
W/R
1xx1b
2
P2DAT
W/R
1111b
P2CR
W
1111b
Port 2 - control register
SC
W
1x11b
System configuration register
M3
20
CWD
R
xxxxb
Watchdog reset
M3
13
Auxiliary
3
Auxiliary
CM
4
Auxiliary
5
Auxiliary
6
Auxiliary
7
Reset Value
Module
Type
Name
Register Function
26
W
1111b
Clock management register
M2
20
P4DAT
W/R
1111b
Port 4 - data register/pin data
M2
30
P4CR
W
1111 1111b
Port 4 - control register (byte)
P5DAT
W/R
1111b
Port 5 - data register/pin data
P5CR
W
1111 1111b
Port 5 - control register (byte)
P6DAT
W/R
1xx1b
Port 6 - data register/pin data
P6CR
W
1111b
Port 6 - control register (byte)
T12SUB
W
–
30
M2
28
28
M2
31
31
Data to Timer 1/2 subport
M1
22
Subport address
0
T2C
W
0000b
Timer 2 control register
M1
43
1
T2M1
W
1111b
Timer 2 mode register 1
M1
43
2
T2M2
W
1111b
Timer 2 mode register 2
M1
44
3
T2CM
W
0000b
Timer 2 compare mode register
M1
46
4
T2CO1
W
1111b
Timer 2 compare register 1
M1
46
5
T2CO2
W
1111 1111b
Timer 2 compare register 2 (byte)
M1
46
6
–
–
–
Reserved
7
–
–
–
8
T1C1
W
1111b
Timer 1 control register 1
M1
34
9
T1C2
W
x111b
Timer 1 control register 2
M1
35
A
WDC
W
1111b
Watchdog control register
M1
35
ASW
22
M2
72
B-F
Reserved
Reserved
8
ASW
W
1111b
9
STB
W
xxxx xxxxb
Serial transmit buffer (byte)
SRB
R
xxxx xxxxb
Serial receive buffer (byte)
SIC1
W
1111b
Serial interface control register 1
SISC
W/R
1x11b
Serial interface status/control register
SIC2
W
1111b
Serial interface control register 2
W/R
–
Auxiliary
A
Auxiliary
B
T3SUB
Auxiliary/switch register
Data to/from Timer 3 subport
72
69
M2
71
70
M1
22
Subport address
0
T3M
W
1111b
Timer 3 mode register
M1
55
1
T3CS
W
1111b
Timer 3 clock select register
M1
57
2
T3CM1
W
0000b
Timer 3 compare mode register 1
M1
58
3
T3CM2
W
0000b
Timer 3 compare mode register 2
M1
59
4
T3CO1
W
1111 1111b
Timer 3 compare register 1 (byte)
M1
59
4
T3CP
R
xxxx xxxxb
Timer 3 capture register (byte)
M1
60
5
T3CO2
W
1111 1111b
Timer 3 compare register 2 (byte)
M1
59
W
1111b
T3C
W
0000b
Timer 3 control register
M3
56
T3ST
R
x000b
Timer 3 status register
M3
57
6
7-F
C
D, E
F
–
---
–
Reserved
Reserved
Reserved
VMC
W
1111b
Voltage monitor control register
M3
14
VMST
R
xx11b
Voltage monitor status register
M3
14
23
4680C–4BMCU–01/05
5.2
Bi-directional Ports
With the exception of Port 1 and Port 6, all other ports (2, 4 and 5) are 4 bits wide. Port 1 and
Port 6 have a data width of 2 bits (bit 0 and bit 3). All ports may be used for data input or output.
All ports are equipped with Schmitt trigger inputs and a variety of mask options for open drain,
open source, full complementary outputs, pull-up and pull-down transistors. All Port Data Registers (PxDAT) are I/O mapped to the primary address register of the respective port address and
the Port Control Register (PxCR), to the corresponding auxiliary register.
There are five different directional ports available:
5.2.1
Port 1
2-bit wide bi-directional ports with automatic full bus width direction switching
Port 2
4-bit wide bit-wise-programmable I/O port
Port 5
4-bit wide bit-wise-programmable bi-directional port with optional strong pull-ups
and programmable interrupt logic
Port 4
4-bit wide bit-wise-programmable bi-directional port also provides the I/O interface
to Timer 2, SSI, voltage monitor input and external interrupt input
Port 6
2-bit wide bit-wise-programmable bi-directional port also provides the I/O interface
to Timer 3 and external interrupt input
Bi-directional Port 1
In Port 1 the data direction register is not independently software programmable, the direction of
the complete port being switched automatically when an I/O instruction occurs (see Figure 5-2
on page 25). The port is switched to output mode via an OUT instruction and to input via an IN
instruction. The data written to a port will be stored into the output data latches and appears
immediately at the port pin following the OUT instruction. After RESET all output latches are set
to '1' and the port is switched to input mode. An IN instruction reads the condition of the associated pins.
Note:
24
Care must be taken when switching the bi-directional port from output to input. The capacitive pin
loading at this port in conjunction with the high resistance pull-ups may cause the CPU to read the
contents of the output data register rather than the external input state. To avoid this, one of the
following programming techniques should be used:
Use two IN-instructions and DROP the first data nibble. The first IN switches the port from output
to input and the DROP removes the first invalid nibble. The second IN reads the valid pin state.
Use an OUT-instruction followed by an IN-instruction. Via the OUT-instruction, the capacitive load
is charged or discharged depending on the optional pull-up/pull-down configuration. Write a '1' for
pins with pull-up resistors and a '0' for pins with pull-down resistors.
ATAM893-D
4680C–4BMCU–01/05
ATAM893-D
Figure 5-2.
Bi-directional Port 1
VDD
I/O Bus
(1)
(Data out)
D
(1)
Q
Static
pull-up
Switched
pull-up
BP1y
P1DATy
R
(1)
Reset
(Direction)
VDD
(1)
OUT
S
Q
(1)
IN
R
NQ
Flash options
Switched
pull-down
Static
pull-down
Master reset
5.2.2
Bi-directional Port 2
As all other bi-directional ports, this port includes a bit-wise programmable Control Register
(P2CR), which enables the individual programming of each port bit as input or output. It also
opens up the possibility of reading the pin condition when in output mode. This is a useful feature for self testing and for serial bus applications.
However, Port 2 has an increased drive capability and an additional low resistance pull-up/down transistor mask option.
Note:
Care should be taken connecting external components to BP20/NTE. During any reset phase, the
BP20/NTE input is driven towards VDD by an additional internal strong pull-up transistor. This pin
must not be pulled down (active or passive) to VSS during reset by any external circuitry representing a resistor of less than 150 kΩ. This prevents the circuit from unintended switching to test mode
enable through the application circuitry at pin BP20/NTE. Resistors less than 150 kΩ might lead to
an undefined state of the internal test logic, thus disabling the application firmware.
To avoid any conflict with the optional internal pull-down transistors, BP20 handles the pull-down
options in a different way than all other ports. BP20 is the only port that switches off the pull-down
transistors during reset.
25
4680C–4BMCU–01/05
Figure 5-3.
Bi-directional Port 2
VDD
Switched
pull-up
I/O Bus
(1)
(Data out)
(1)
Static
Pull-up
(1)
I/O Bus
D
Q
P2DATy
BP2y
S
VDD
(1)
Master reset
I/O Bus
(1)
D S Q
(1)
Static
Pull-down
P2CRy
(1)
(Direction)
5.2.2.1
Flash options
Switched
pull-down
Port 2 Data Register (P2DAT)
Primary register address: '2'hex
P2DAT
Bit 3
Bit 2
Bit 1
Bit 0
P2DAT3
P2DAT2
P2DAT1
P2DAT0
Reset value: 1111b
Bit 3 = MSB, Bit 0 = LSB
5.2.2.2
Port 2 Control Register (P2CR)
Auxiliary register address: '2'hex
P2CR
Bit 3
Bit 2
Bit 1
Bit 0
P2CR3
P2CR2
P2CR1
P2CR0
Reset value: 1111b
Value 1111b means all pins in input mode
Table 5-2.
26
Port 2 Control Register
Code
3210
Function
xxx1
BP20 in input mode
xxx0
BP20 in output mode
xx1x
BP21 in input mode
xx0x
BP21 in output mode
x1xx
BP22 in input mode
x0xx
BP22 in output mode
1xxx
BP23 in input mode
0xxx
BP23 in output mode
ATAM893-D
4680C–4BMCU–01/05
ATAM893-D
5.2.3
Bi-directional Port 5
As all other bi-directional ports, this port includes a bit-wise programmable Control Register
(P5CR), which allows the individual programming of each port bit as input or output. It also
opens up the possibility of reading the pin condition when in output mode. This is a useful feature for self testing and for serial bus applications.
The port pins can also be used as external interrupt inputs (see Figure 5-4 and Figure 5-5 on
page 28). The interrupts (INT1 and INT6) can be masked or independently configured to trigger
on either edge. The interrupt configuration and port direction is controlled by the Port 5 Control
Register (P5CR). An additional low resistance pull-up/-down transistor mask option provides an
internal bus pull-up for serial bus applications.
The Port 5 Data Register (P5DAT) is I/O mapped to the primary address register of address ’5’h
and the Port 5 Control Register (P5CR) to the corresponding auxiliary register. The P5CR is a
byte-wide register and is configured by writing first the low nibble and then the high nibble (see
Section 5.1 on page 22).
Figure 5-4.
Bi-directional Port 5
Switched
pull-up
I/O Bus
VDD
(1)
(1)
Static
pull-up
VDD
(Data out)
(1)
I/O Bus
Q
D
P5DATy
BP5y
(1)
S
VDD
Master reset
(1)
IN enable
(1)
Flash options
(1)
Static
Pull-down
Switched
pull-down
27
4680C–4BMCU–01/05
Figure 5-5.
Port 5 External Interrupts
INT1
INT6
Data in
Data in
BP52
BP51
Bidir. Port
Bidir. Port
IN_Enable
IN_Enable
I/O-bus
I/O-bus
Data in
Data in
BP53
BP50
Bidir. Port
Bidir. Port
IN_Enable
IN_Enable
Decoder
P5CR:
5.2.3.1
Decoder
Decoder
Decoder
P53M2 P53M1 P52M2 P52M1 P51M2 P51M1 P50M2 P50M1
Port 5 Data Register (P5DAT)
Primary register address: '5'hex
P5DAT
5.2.3.2
Bit 3
Bit 2
Bit 1
Bit 0
P5DAT3
P5DAT2
P5DAT1
P5DAT0
Reset value: 1111b
Port 5 Control Register (P5CR) Byte Write
Auxiliary register address: '5'hex
P5CR
First write
cycle
Second
write cycle
Bit 3
Bit 2
Bit 1
Bit 0
P51M2
P51M1
P50M2
P50M1
Bit 7
Bit 6
Bit 5
Bit 4
P53M2
P53M1
P52M2
P52M1
Reset value: 1111b
Reset value: 1111b
P5xM2, P5xM1 – Port 5x Interrupt Mode/Direction Code
28
ATAM893-D
4680C–4BMCU–01/05
ATAM893-D
Table 5-3.
Port 5 Control Register
Auxiliary Address: '5'hex First Write Cycle
Second Write Cycle
Code
3210
Function
xx11
BP50 in input mode – interrupt disabled
xx11
BP52 in input mode – interrupt disabled
xx01
BP50 in input mode – rising edge interrupt
xx01
BP52 in input mode – rising edge interrupt
xx10
BP50 in input mode – falling edge interrupt
xx10
BP52 in input mode – falling edge interrupt
xx00
BP50 in output mode – interrupt disabled
xx00
BP52 in output mode – interrupt disabled
11xx
BP51 in input mode – interrupt disabled
11xx
BP53 in input mode – interrupt disabled
01xx
BP51 in input mode – rising edge interrupt
01xx
BP53 in input mode – rising edge interrupt
10xx
BP51 in input mode – falling edge interrupt
10xx
BP53 in input mode – falling edge interrupt
00xx
BP51 in output mode – interrupt disabled
00xx
BP53 in output mode – interrupt disabled
5.2.4
Code
3210
Function
Bi-directional Port 4
The bi-directional Port 4 is a bit-wise configurable I/O port and provides the external pins for the
Timer 2, SSI and the voltage monitor input (VMI). As a normal port, it performs in exactly the
same way as bi-directional Port 2 (see Figure 5-6). Two additional multiplexes allow data and
port direction control to be passed over to other internal modules (Timer 2, VM or SSI). The I/O
pins for the SC and SD lines have an additional mode to generate an SSI-interrupt.
All four Port 4 pins can be individually switched by the P4CR register. Figure 5-6 shows the internal interfaces to bi-directional Port 4.
Figure 5-6.
Bi-directional Port 4 and Port 6
VDD
I/O Bus
Intx
(1)
(1)
PxMRy
PIn
Static
pull-up
VDD
POut
(1)
I/O Bus
Switched
pull-up
Q
D
BPxy
PxDATy
S
VDD
(1)
Master reset
(Direction)
I/O Bus
D
S
(1)
Q
(1)
Static
pull-down
PxCRy
PDir
(1)
Flash options
Switched
pull-down
29
4680C–4BMCU–01/05
5.2.4.1
Port 4 Data Register (P4DAT)
Primary register address: '4'hex
P4DAT
5.2.4.2
Bit 3
Bit 2
Bit 1
Bit 0
P4DAT3
P4DAT2
P4DAT1
P4DAT0
Reset value: 1111b
Port 4 Control Register (P4CR) Byte Write
Auxiliary register address: '4'hex
P4CR
First write cycle
Second write
cycle
Bit 3
Bit 2
Bit 1
Bit 0
P41M2
P41M1
P40M2
P40M1
Bit 7
Bit 6
Bit 5
Bit 4
P43M2
P43M1
P42M2
P42M1
Reset value: 1111b
Reset value: 1111b
P4xM2, P4xM1 – Port 4x Interrupt Mode/Direction Code
Table 5-4.
Port 4 Control Register
Auxiliary Address: '4'hex First Write Cycle
Second Write Cycle
Code
3210
Function
Code
3210
Function
xx11
BP40 in input mode
xx11
BP42 in input mode
xx10
BP40 in output mode
xx10
BP42 in output mode
xx01
BP40 enable alternate function (SC for SSI)
xx0x
BP42 enable alternate function (T2O for Timer 2)
xx00
BP40 enable alternate function (falling edge interrupt
input for INT3)
11xx
BP43 in input mode
11xx
BP41 in input mode
10xx
BP43 in output mode
10xx
BP41 in output mode
01xx
BP43 enable alternate function (SD for SSI)
01xx
BP41 enable alternate function
(VMI for voltage monitor input)
00xx
BP43 enable alternate function (falling edge interrupt
input for INT3)
00xx
BP41 enable alternate function
(T2I external clock input for Timer 2)
5.2.5
–
–
Bi-directional Port 6
The bi-directional Port 6 is a bit-wise configurable I/O port and provides the external pins for the
Timer 3. As a normal port, it performs in exactly the same way as bi-directional Port 6 (see Figure 5-6 on page 29). Two additional multiplexes allow data and port direction control to be
passed over to other internal modules (Timer 3). The I/O pin for the T3I line has an additional
mode to generate a Timer 3-interrupt.
All two Port 6 pins can be individually switched by the P6CR register. Figure 5-6 on page 29
shows the internal interfaces to bi-directional Port 6.
30
ATAM893-D
4680C–4BMCU–01/05
ATAM893-D
5.2.5.1
Port 6 Data Register (P6DAT)
Primary register address: '6'hex
P6DAT
5.2.5.2
Bit 3
Bit 2
Bit 1
Bit 0
P6DAT3
–
–
P6DAT0
Reset value: 1xx1b
Port 6 Control Register (P6CR)
Primary register address: '6'hex
P6CR
Bit 3
Bit 2
Bit 1
Bit 0
P63M2
P63M1
P60M2
P60M0
Reset value: 1111b
P6xM2, P6xM1 - Port 6x Interrupt mode/direction code
Table 5-5.
Port 6 Control Register
Auxiliary Address: ‘6’hex
5.3
Write Cycle
Code
3210
Function
Code
3210
Function
xx11
BP60 in input mode
11xx
BP63 in input mode
xx10
BP60 in output mode
10xx
BP63 in output mode
xx0x
BP60 enable alternate port function
(T3O for Timer 3)
0xxx
BP63 enable alternate port function (T3I
for Timer 3)
Universal Timer/Counter/ Communication Module (UTCM)
The Universal Timer/counter/Communication Module (UTCM) consists of three timers
(Timer 1,Timer 2, Timer 3) and a Synchronous Serial Interface (SSI).
• Timer 1 is an interval timer that can be used to generate periodic interrupts and as prescaler
for Timer 2, Timer 3, the serial interface and the watchdog function.
• Timer 2 is an 8/12-bit timer with an external clock input (T2I) and an output (T2O).
• Timer 3 is an 8-bit timer/counter with its own input (T3I) and output (T3O).
• The SSI operates as a two-wire serial interface or as shift register for modulation and
demodulation. The modulator and demodulator units work together with the timers and shift
the data bits into or out of the shift register.
There is a multitude of modes in which the timers and the serial interface can work together.
31
4680C–4BMCU–01/05
Figure 5-7.
UTCM Block Diagram
SYSCL
from clock module
SUBCL
Timer 1
NRST
Watchdog
MUX
INT2
Interval/Prescaler
Timer 3
T1OUT
Capture 3
T3I
8-bit Counter 3
MUX
Compare 3/1
Control
Demodulator 3
Modulator 3
T3O
INT5
Compare 3/2
Timer 2
TOG3
4-bit Counter 2/1
MUX
Compare 2/1
Modulator 2
T2O
I/O bus
Control
POUT
T2I
8-bit Counter 2/2
MUX
DCG
INT4
Compare 2/2
TOG2
SSI
SCL
Receive-Buffer
MUX
8-bit Shift-Register
SC
Control
SD
Transmit-Buffer
5.3.1
INT3
Timer 1
The Timer 1 is an interval timer which can be used to generate periodic interrupts and as prescaler for Timer 2, Timer 3, the serial interface and the watchdog function.
The Timer 1 consists of a programmable 14-stage divider that is driven by either SUBCL or
SYSCL. The timer output signal can be used as prescaler clock or as SUBCL and as source for
the Timer 1 interrupt. Because of other system requirements the Timer 1 output T1OUT is synchronized with SYSCL. Therefore, in the power-down mode SLEEP (CPU core →sleep and
OSC-Stop →yes) the output T1OUT is stopped (T1OUT = 0). Nevertheless, the Timer 1 can be
active in SLEEP and generate Timer 1 interrupts. The interrupt is maskable via the T1IM bit and
the SUBCL can be bypassed via the T1BP bit of the T1C2 register. The time interval for the
timer output can be programmed via the Timer 1 control register T1C1.
32
ATAM893-D
4680C–4BMCU–01/05
ATAM893-D
This timer starts running automatically after any power-on reset! If the watchdog function is not
activated, the timer can be restarted by writing into the T1C1 register with T1RM = 1.
Timer 1 can also be used as a watchdog timer to prevent a system from stalling. The watchdog
timer is a 3-bit counter that is supplied by a separate output of Timer 1. It generates a system
reset when the 3-bit counter overflows. To avoid this, the 3-bit counter must be reset before it
overflows. The application software has to accomplish this by reading the CWD register.
After power-on reset the watchdog must be activated by software in the $RESET initialization
routine. There are two watchdog modes, in one mode the watchdog can be switched on and off
by software, in the other mode the watchdog is active and locked. This mode can only be
stopped by carrying out a system reset.
The watchdog timer operation mode and the time interval for the watchdog reset can be programmed via the watchdog control register (WDC).
Figure 5-8.
Timer 1 Module
SYSCL
SUBCL
WDCL
MUX
CL1
14-bit
Prescaler
4-bit
Watchdog
NRST
INT2
T1CS
T1BP
T1IM
T1OUT
T1MUX
Figure 5-9.
Timer 1 and Watchdog
T1C1 T1RM T1C2 T1C1 T1C0
T1C2
T1BP T1IM
3
Write of the
T1C1 register
T1IM=0
T1MUX
Decoder
INT2
MUX for interval timer
T1IM=1
T1OUT
RES Q1 Q2 Q3 Q4 Q5
CL1
CL
Q6
Q8
Q11
Q14 SUBCL
Q8
Q11
Q14
Watchdog
Divider/8
Decoder
MUX for watchdog timer
2
WDC
WDL
WDR WDT1 WDT0
WDCL
Divider
RESET
RESET
(NRST)
RES
Watchdog
mode control
Read of the
CWD register
33
4680C–4BMCU–01/05
5.3.1.1
Timer 1 Control Register 1 (T1C1)
Address: '7'hex - Subaddress: '8'hex
T1C1
Bit 3
Bit 2
Bit 1
Bit 0
T1RM
T1C2
T1C1
T1C0
Reset value: 1111b
Bit 3 = MSB, Bit 0 = LSB
T1RM
Timer 1 Restart Mode
T1RM = 0, write access without Timer 1 restart
T1RM = 1, write access with Timer 1 restart
Note: if WDL = 0, Timer 1 restart is impossible
T1C2
Timer 1 Control bit 2
T1C1
Timer 1 Control bit 1
T1C0
Timer 1 Control bit 0
The three bits T1C[2:0] select the divider for timer 1. The resulting time interval depends on this
divider and the timer 1 input clock source. The timer input can be supplied by the system clock,
the 32-kHz oscillator or via the clock management. If the clock management generates the
SUBCL, the selected input clock from the RC oscillator, 4-MHz oscillator or an external clock is
divided by 16.
Table 5-6.
34
Timer 1 Control Bits
T1C2
T1C1
T1C0
Divider
Time Interval with
SUBCL
Time Interval with
SUBCL = 32 kHz
Time Interval with
SYSCL = 2/1 MHz
0
0
0
2
SUBCL/2
61 µs
1 µs/2 µs
0
0
1
4
SUBCL/4
122 µs
2 µs/4 µs
0
1
0
8
SUBCL/8
244 µs
4 µs/8 µs
0
1
1
16
SUBCL/16
488 µs
8 µs/16 µs
1
0
0
32
SUBCL/32
0.977 ms
16 µs/32 µs
1
0
1
256
SUBCL/256
7.812 ms
128 µs/256 µs
1
1
0
2048
SUBCL/2048
62.5 ms
1024 µs/2048 µs
1
1
1
16384
SUBCL/16384
500 ms
8192 µs/16384 µs
ATAM893-D
4680C–4BMCU–01/05
ATAM893-D
5.3.1.2
Timer 1 Control Register 2 (T1C2)
Address: ’7’hex - Subaddress: ’9’hex
T1C2
Bit 3
Bit 2
Bit 1
Bit 0
–
T1BP
T1CS
T1IM
Reset value: x111b
Bit 3 = MSB, Bit 0 = LSB
5.3.1.3
T1BP
Timer 1 SUBCL ByPassed
T1BP = 1, TIOUT = T1MUX
T1BP = 0, T1OUT = SUBCL
T1CS
Timer 1 input Clock Select
T1CS = 1, CL1 = SUBCL (see Figure 5-8 on page 33)
T1CS = 0, CL1 = SYSCL (see Figure 5-8 on page 33)
T1IM
Timer 1 Interrupt Mask
T1IM = 1, disables Timer 1 interrupt
T1IM = 0, enables Timer 1 interrupt
Watchdog Control Register (WDC)
Address: ’7’hex - Subaddress: ’A’hex
WDC
Bit 3
Bit 2
Bit 1
Bit 0
WDL
WDR
WDT1
WDT0
Reset value: 1111b
Bit 3 = MSB, Bit 0 = LSB
WDL
WatchDog Lock mode
WDL = 1, the watchdog can be enabled and disabled by using the WDR-bit
WDL = 0, the watchdog is enabled and locked. In this mode the WDR-bit has no
effect. After the WDL-bit is cleared, the watchdog is active until a system
reset or power-on reset occurs.
WDR
WatchDog Run and stop mode
WDR = 1, the watchdog is stopped/disabled
WDR = 0, the watchdog is active/enabled
WDT1
WatchDog Time 1
WDT0
WatchDog Time 0
Both these bits control the time interval for the watchdog reset.
35
4680C–4BMCU–01/05
Table 5-7.
5.3.2
Watchdog Time Control Bits
WDT1
WDT0
Divider
Delay Time to Reset with
SUBCL = 32 kHz
Delay Time to Reset with
SYSCL = 2/1 MHz
0
0
512
15.625 ms
0.256 ms/0.512 ms
0
1
2048
62.5 ms
1.024 ms/2.048 ms
1
0
16384
0.5 s
8.2 ms/16.4 ms
1
1
131072
4s
65.5 ms/131 ms
Timer 2
Timer 2 is an 8/12-bit timer used for:
• Interrupt, square-wave, pulse and duty cycle generation
• Baud-rate generation for the internal shift register
• Manchester and Bi-phase modulation together with the SSI
• Carrier frequency generation and modulation together with the SSI
Timer 2 can be used as interval timer for interrupt generation, as signal generator or as baudrate generator and modulator for the serial interface. It consists of a 4-bit and an 8-bit up counter
stage which both have compare registers. The 4-bit counter stages of Timer 2 are cascadable
as a 12-bit timer or as an 8-bit timer with a 4-bit prescaler. The timer can also be configured as
an 8-bit timer and separate a 4-bit prescaler.
The Timer 2 input can be supplied via the system clock, the external input clock (T2I), the Timer
1 output clock, the Timer 3 output clock or the shift clock of the serial interface. The external
input clock T2I is not synchronized with SYSCL. Therefore, it is possible to use Timer 2 with a
higher clock speed than SYSCL. Furthermore, with that input clock the Timer 2 operates in the
power-down mode SLEEP (CPU core →sleep and OSC-Stop →yes) as well as in POWERDOWN (CPU core →sleep and OSC-Stop →no). All other clock sources supply no clock signal in
SLEEP if NSTOP = 0. The 4-bit counter stages of Timer 2 have an additional clock output
(POUT).
Its output has a modulator stage that allows the generation of pulses as well as the generation
and modulation of carrier frequencies. The Timer 2 output can modulate with the shift register
data output to generate Bi-phase- or Manchester code.
If the serial interface is used to modulate a bit-stream, the 4-bit stage of Timer 2 has a special
task. The shift register can only handle bit-stream lengths divisible by 8. For other lengths, the
4-bit counter stage can be used to stop the modulator after the right bit-count is shifted out.
If the timer is used for carrier frequency modulation, the 4-bit stage works together with an additional 2-bit duty cycle generator like a 6-bit prescaler to generate carrier frequency and duty
cycle. The 8-bit counter is used to enable and disable the modulator output for a programmable
count of pulses.
For programming the time interval, the timer has a 4-bit and an 8-bit compare register. For programming the timer function, it has four mode and control registers. The comparator output of
stage 2 is controlled by a special compare mode register (T2CM). This register contains mask
bits for the actions (counter reset, output toggle, timer interrupt) which can be triggered by a
compare match event or the counter overflow. This architecture enables the timer function for
various modes.
36
ATAM893-D
4680C–4BMCU–01/05
ATAM893-D
The Timer 2 has a 4-bit compare register (T2CO1) and an 8-bit compare register (T2CO2). Both
these compare registers are cascadable as a 12-bit compare register, or 8-bit compare register
and 4-bit compare register.
For 12-bit compare data value:
m = x +1
0 ≤x ≤4095
For 8-bit compare data value:
n=y+1
0 ≤y ≤255
For 4-bit compare data value:
l = z +1
0 ≤z ≤15
Figure 5-10. Timer 2
I/O-bus
P4CR
T2M1
T2M2
T2I
DCGO
SYSCL
T1OUT
TOG3
SCL
CL2/1
4-bit Counter 2/1
RES
T2O
CL2/2
OVF1
DCG
POUT
8-bit Counter 2/2
RES
OUTPUT
OVF2
TOG2
T2C
Compare 2/1
Control
M2
Compare 2/2
MOUT
to
Modulator 3
INT4
Bi-phase
CM1
T2CO1
T2CM
Manchester
modulator
T2CO2
Timer 2
modulator
output-stage
SSI POUT
SO
Control
I/O-bus
SSI
5.3.2.1
SSI
Timer 2 Modes
Mode 1: 12-bit Compare Counter
The 4-bit stage and the 8-bit stage work together as a 12-bit compare counter. A compare match
signal of the 4-bit and the 8-bit stage generates the signal for the counter reset, toggle flip-flop or
interrupt. The compare action is programmable via the compare mode register (T2CM). The 4bit counter overflow (OVF1) supplies the clock output (POUT) with clocks. The duty cycle generator (DCG) has to be bypassed in this mode.
Figure 5-11. 12-bit Compare Counter
POUT (CL2/1 /16)
CL2/1
4-bit counter
DCG
OVF2
8-bit counter
RES
TOG2
RES
INT4
4-bit compare
8-bit compare
CM2
CM1
4-bit register
T2D1, 0
Timer 2
output mode
and T2OTM-bit
8-bit register
T2RM
T2OTM
T2IM
T2CTM
37
4680C–4BMCU–01/05
Mode 2: 8-bit Compare Counter with 4-bit Programmable Prescaler
The 4-bit stage is used as a programmable prescaler for the 8-bit counter stage. In this mode, a
duty cycle stage is also available. This stage can be used as an additional 2-bit prescaler or for
generating duty cycles of 25%, 33% and 50%. The 4-bit compare output (CM1) supplies the
clock output (POUT) with clocks.
Figure 5-12. 8-bit Compare Counter
DCGO
POUT
CL2/1
4-bit counter
DCG
OVF2
8-bit counter
RES
TOG2
RES
INT4
4-bit compare
CM2
8-bit compare
CM1
4-bit register
T2D1, 0
Timer 2
output mode
and T2OTM-bit
8-bit register
T2RM
T2OTM
T2IM
T2CTM
Mode 3/4: 8-bit Compare Counter and 4-bit Programmable Prescaler
In these modes the 4-bit and the 8-bit counter stages work independently as a 4-bit prescaler
and an 8-bit timer with an 2-bit prescaler or as a duty cycle generator. Only in the mode 3 and
mode 4, can the 8-bit counter be supplied via the external clock input (T2I) which is selected via
the P4CR register. The 4-bit prescaler is started via activating of mode 3 and stopped and reset
in mode 4. Changing mode 3 and 4 has no effect for the 8-bit timer stage. The 4-bit stage can be
used as prescaler for Timer 3, the SSI or to generate the stop signal for modulator 2 and
modulator 3.
Figure 5-13. 4-/8-bit Compare Counter
DCGO
T2I
CL2/2
SYSCL
DCG
8-bit counter
OVF2
TOG2
RES
INT4
8-bit compare
CM2
Timer 2
output mode
and T2OTM-bit
P4CR P41M2, 1
TOG3
T1OUT
SYSCL
SCL
MUX
T2D1, 0
CL2/1
8-bit register
T2OTM
T2IM
T2CTM
4-bit counter
RES
4-bit compare
T2CS1, 0
38
T2RM
CM1
POUT
4-bit register
ATAM893-D
4680C–4BMCU–01/05
ATAM893-D
5.3.2.2
Timer 2 Output Modes
The signal at the timer output is generated via modulator 2. In the toggle mode, the compare
match event toggles the output T2O. For high resolution duty cycle modulation 8 bits or 12 bits
can be used to toggle the output. In the duty cycle burst modulator modes the DCG output is
connected to T2O and switched on and off either by the toggle flipflop output or the serial data
line of the SSI. Modulator 2 also has 2 modes to output the content of the serial interface as Biphase or Manchester code.
The modulator output stage can be configured by the output control bits in the T2M2 register.
The modulator is started with the start of the shift register (SIR = 0) and stopped either by carrying out a shift register stop (SIR = 1) or compare match event of stage 1 (CM1) of Timer 2. For
this task, Timer 2 mode 3 must be used and the prescaler has to be supplied with the internal
shift clock (SCL).
Figure 5-14. Timer 2 Modulator Output Stage
DCGO
SO
TOG2
T2O
RE
SSI
CONTROL
Bi-phase/
Manchester
modulator
FE
S1
S3
M2
Toggle
S2
RES/SET
Modulator 3
OMSK
M2
T2M2
5.3.2.3
T2OS2, 1, 0 T2TOP
Timer 2 Output Signals
Timer 2 Output Mode 1
Toggle Mode A: A Timer 2 compare match toggles the output flip-flop (M2) →T2O
Figure 5-15. Interrupt Timer/Square Wave Generator – the Output Toggles with Each Edge
Compare Match Event
Input
Counter 2
T2R
Counter 2
0
0
0
1
2
3
4
0
1
2
3
4
0
1
2
3
4
0
1
CMx
INT4
T2O
39
4680C–4BMCU–01/05
Toggle Mode B: A Timer 2 compare match toggles the output flip-flop (M2) →T2O
Figure 5-16. Pulse Generator – the Timer Output Toggles with the Timer Start if the T2TS-bit
Is Set
Input
Counter 2
T2R
0
0
0
1
2
3
4
5
6
7
4095/
255 0
1
2
3
4
5
6
Counter 2
CMx
INT4
T2O
Toggle
by start
T2O
Toggle Mode C: A Timer 2 compare match toggles the output flip-flop (M2) →T2O
Figure 5-17. Pulse Generator – the Timer Toggles with Timer Overflow and Compare Match
Input
Counter 2
T2R
0
0
0
1
2
3
4
5
6
7
4095/
255 0
1
2
3
4
5
6
Counter 2
CMx
OVF2
INT4
T2O
40
ATAM893-D
4680C–4BMCU–01/05
ATAM893-D
Timer 2 Output Mode 2
Duty Cycle Burst Generator 1: The DCG output signal (DCGO) is given to the output, and
gated by the output flip-flop (M2)
Figure 5-18. Carrier Frequency Burst Modulation with Timer 2 Toggle Flip-flop Output
DCGO
1 2 0 1 2 0 1 2 3 4 5 0 1 2 0 1 2 3 4 5 6 7 8 0 1 2 3 4 5 6 7 8 9 10 0 1 2 3 4 5
Counter 2
TOG2
M2
T2O
Counter = compare register (= 2)
Timer 2 Output Mode 3
Duty Cycle Burst Generator 2: The DCG output signal (DCGO) is given to the output, and
gated by the SSI internal data output (SO)
Figure 5-19. Carrier Frequency Burst Modulation with the SSI Data Output
DCGO
1 2 0 1 2 0 1 2 0 1 2 0 1 2 0 1 2 0 1 2 0 1 2 0 1 2 0 1 2 0 1 2 0 1 2 0 1 2 0 1
Counter 2
Counter = compare register (= 2)
TOG2
SO
Bit 0
Bit 1
Bit 2
Bit 3
Bit 4
Bit 5
Bit 6
Bit 7
Bit 8
Bit 9
Bit 10
Bit 11
Bit 12
Bit 13
T2O
Timer 2 Output Mode 4
Bi-phase Modulator: Timer 2 Modulates the SSI Internal Data Output (SO) to Bi-phase Code.
Figure 5-20. Bi-phase Modulation
TOG2
SC
8-bit SR Data
SO
0
0
1
1
0
1
0
T2O
0
1
Bit 0
Bit 7
0
1
1
0
1
0
1
Data: 00110101
41
4680C–4BMCU–01/05
Timer 2 Output Mode 5
Manchester Modulator: Timer 2 Modulates the SSI internal data output (SO) to Manchester
code
Figure 5-21. Manchester Modulation
TOG2
SC
8-bit SR Data
0
SO
0
1
1
0
1
0
1
Bit 0
Bit 7
0
T2O
0
1
1
0
1
0
1
Bit 7
Bit 0
Data: 00110101
Timer 2 Output Mode 7
PWM Mode: Pulse-width modulation output on Timer 2 output pin (T2O)
In this mode the timer overflow defines the period and the compare register defines the duty
cycle. During one period only the first compare match occurrence is used to toggle the timer output flip-flop. Until the overflow all further compare match are ignored. This avoids the situation
that changing the compare register causes the occurrence of several compare match during one
period. The resolution at the pulse-width modulation Timer 2 mode 1 is 12-bit and all other
Timer 2 modes are 8-bit.
Figure 5-22. PWM Modulation
Input clock
Counter 2/2
T2R
0
0
50
255 0
100
255 0
150
255 0 50
255 0
100
Counter 2/2
CM2
OVF2
load the next
compare value
INT4
T2O
T1
T2
T
5.3.2.4
42
T2CO2 = 150
load
T3
T
load
T1
T
T2
T
T
Timer 2 Registers
Timer 2 has 6 control registers to configure the timer mode, the time interval, the input clock and
its output function. All registers are indirectly addressed using extended addressing as
described in Section 5.1 on page 22. The alternate functions of the Ports BP41 or BP42 must be
selected with the Port 4 control register P4CR, if one of the Timer 2 modes require an input at
T2I/BP41 or an output at T2O/BP42.
ATAM893-D
4680C–4BMCU–01/05
ATAM893-D
5.3.2.5
Timer 2 Control Register (T2C)
Address: '7'hex — Subaddress: '0'hex
Bit 3
Bit 2
Bit 1
Bit 0
T2C
T2CS1
T2CS0
T2TS
T2R
T2CS1
Timer 2 Clock Select bit 1
T2CS0
Timer 2 Clock Select bit 0
T2TS
Timer 2 Toggle with Start
T2TS = 0, the output flip-flop of Timer 2 is not toggled with the timer start
T2TS = 1, the output flip-flop of Timer 2 is toggled when the timer is started with T2R
T2R
Timer 2 Run
T2R = 0, Timer 2 stop and reset
T2R = 1, Timer 2 run
Table 5-8.
5.3.2.6
Reset value: 0000b
Timer 2 Clock Select Bits
T2CS1
T2CS0
Input Clock (CL 2/1) of Counter Stage 2/1
0
0
System clock (SYSCL)
0
1
Output signal of Timer 1 (T1OUT)
1
0
Internal shift clock of SSI (SCL)
1
1
Output signal of Timer 3 (TOG3)
Timer 2 Mode Register 1 (T2M1)
Address: '7'hex — Subaddress: '1'hex
Bit 3
Bit 2
Bit 1
Bit 0
T2M1
T2D1
T2D0
T2MS1
T2MS0
T2D1
Timer 2 Duty cycle bit 1
T2D0
Timer 2 Duty cycle bit 0
T2MS1
Timer 2 Mode Select bit 1
T2MS0
Timer 2 Mode Select bit 0
Table 5-9.
Reset value: 1111b
Timer 2 Duty Cycle Bits
T2D1
T2D0
Function of Duty Cycle Generator (DCG)
Additional Divider Effect
1
1
Bypassed (DCGO0)
/1
1
0
Duty cycle 1/1 (DCGO1)
/2
0
1
Duty cycle 1/2 (DCGO2)
/3
0
0
Duty cycle 1/3 (DCG03)
/4
43
4680C–4BMCU–01/05
Table 5-10.
Mode
T2MS1
T2MS0
1
1
2
1
3
4
5.3.2.7
Timer 2 Mode Select Bits
0
0
Clock Output (POUT)
Timer 2 Modes
1
4-bit counter overflow (OVF1)
12-bit compare counter, the DCG
have to be bypassed in this mode
0
4-bit compare output (CM1)
8-bit compare counter with 4-bit
programmable prescaler and duty
cycle generator
4-bit compare output (CM1)
8-bit compare counter clocked by
SYSCL or the external clock input
T2I, 4-bit prescaler run, the
counter 2/1 starts after writing
mode 3
4-bit compare output (CM1)
8-bit compare counter clocked by
SYSCL or the external clock input
T2I, 4-bit prescaler stop and
resets
1
0
Duty Cycle Generator
The duty cycle generator generates duty cycles of 25%, 33% or 50%. The frequency at the duty
cycle generator output depends on the duty cycle and the Timer 2 prescaler setting. The DCGstage can also be used as an additional programmable prescaler for Timer 2.
Figure 5-23. DCG Output Signals
DCGIN
DCGO0
DCGO1
DCGO2
DCGO3
5.3.2.8
Timer 2 Mode Register 2 (T2M2)
Address: '7'hex — Subaddress: '2'hex
44
Bit 3
Bit 2
Bit 1
Bit 0
T2M2
T2TOP
T2OS2
T2OS1
T2OS0
T2TOP
Timer 2 Toggle Output Preset
This bit allows the programmer to preset the Timer 2 output T2O.
T2TOP = 0, resets the toggle outputs with the write cycle (M2 = 0)
T2TOP = 1, sets toggle outputs with the write cycle (M2 = 1)
Note: If T2R = 1, no output preset is possible
T2OS2
Timer 2 Output Select bit 2
T2OS1
Timer 2 Output Select bit 1
T2OS0
Timer 2 Output Select bit 0
Reset value: 1111b
ATAM893-D
4680C–4BMCU–01/05
ATAM893-D
Table 5-11.
Timer 2 Output Select Bits
Output Mode
T2OS2
T2OS1
T2OS0
Clock Output
1
1
1
1
Toggle mode: a Timer 2 compare match toggles
the output flip-flop (M2) →T2O
2
1
1
0
Duty cycle burst generator 1: the DCG output
signal (DCG0) is given to the output and gated by
the output flip-flop (M2)
3
1
0
1
Duty cycle burst generator 2: the DCG output
signal (DCGO) is given to the output and gated by
the SSI internal data output (SO)
4
1
0
0
Bi-phase modulator: Timer 2 modulates the SSI
internal data output (SO) to Bi-phase code
5
0
1
1
Manchester modulator: Timer 2 modulates the
SSI internal data output (SO) to Manchester code
6
0
1
0
SSI output: T2O is used directly as SSI internal
data output (SO)
7
0
0
1
PWM mode: an 8/12-bit PWM mode
8
0
0
0
Not allowed
If one of these output modes is used the T2O alternate function of Port 4 must also be activated.
5.3.2.9
Timer 2 Compare and Compare Mode Registers
Timer 2 has two separate compare registers, T2CO1 for the 4-bit stage and T2CO2 for the 8-bit
stage of Timer 2. The timer compares the contents of the compare register current counter value
and if it matches it generates an output signal. Depending on the timer mode, this signal is used
to generate a timer interrupt, to toggle the output flip-flop as SSI clock or as a clock for the next
counter stage.
In the 12-bit timer mode, T2CO1 contains bits 0 to 3 and T2CO2 bits 4 to 11 of the 12-bit compare value. In all other modes, the two compare registers work independently as a 4- and 8-bit
compare register. When assigned to the compare register a compare event will be suppressed.
45
4680C–4BMCU–01/05
5.3.2.10
Timer 2 Compare Mode Register (T2CM)
Address: '7'hex — Subaddress: '3'hex
T2CM
Bit 2
Bit 1
Bit 0
T2OTM
T2CTM
T2RM
T2IM
Reset value: 0000b
T2OTM
Timer 2 Overflow Toggle Mask bit
T2OTM = 0, disable overflow toggle
T2OTM = 1, enable overflow toggle, a counter overflow (OVF2) toggles output
flip-flop (TOG2). If the T2OTM bit is set, only a counter overflow
can generate an interrupt except on the Timer 2 output mode 7
T2CTM
Timer 2 Compare Toggle Mask bit
T2CTM = 0, disable compare toggle
T2CTM = 1, enable compare toggle, a match of the counter with the compare
register toggles output flip-flop (TOG2). In Timer 2 output mode 7
and when the T2CTM bit is set, only a match of the counter with the
compare register can generate an interrupt
T2RM
Timer 2 Reset Mask bit
T2RM = 0, disable counter reset
T2RM = 1, enable counter reset, a match of the counter with the compare register
resets the counter
T2IM
Timer 2 Interrupt Mask bit
T2IM = 0, disable Timer 2 interrupt
T2IM = 1, enable Timer 2 interrupt
Table 5-12.
5.3.2.11
Bit 3
Timer 2 Toggle Mask Bits
Timer 2 Output Mode
T2OTM
T2CTM
1, 2, 3, 4, 5 and 6
0
x
Compare match (CM2)
Timer 2 Interrupt Source
1, 2, 3, 4, 5 and 6
1
x
Overflow (OVF2)
7
x
1
Compare match (CM2)
Timer 2 COmpare Register 1 (T2CO1)
Address: '7'hex — Subaddress: '4'hex
T2CO1
Write cycle
Bit 3
Bit 2
Bit 1
Bit 0
Reset value: 1111b
In prescaler mode the clock is bypassed if the compare register T2CO1 contains 0.
5.3.2.12
Timer 2 COmpare Register 2 (T2CO2) Byte Write
Address: ’7’hex -Subaddress: '5'hex
T2CO2
46
First write cycle
Bit 3
Bit 2
Bit 1
Bit 0
Reset value: 1111b
Second write
cycle
Bit 7
Bit 6
Bit 5
Bit 4
Reset value: 1111b
ATAM893-D
4680C–4BMCU–01/05
ATAM893-D
5.3.3
Timer 3
5.3.3.1
Features
• Two Compare Registers
• Capture Register
• Edge Sensitive Input with Zero Cross Detection Capability
• Trigger and Single Action Modes
• Output Control Modes
• Automatic Modulation and Demodulation Modes
• FSK Modulation
• Pulse width Modulation (PWM)
• Manchester Demodulation Together with SSI
• Bi-phase Demodulation Together with SSI
• Pulse-width Demodulation Together with SSI
Figure 5-24. Timer 3
I/O-bus
T3CS
T3M
T3I
T3EX
SCI
T3I
CP3
T3CP
Demodulator 3
CM31
SI
RES
T3EX
SYSCL
T1OUT
POUT
CL3
INT5
8-bit Counter 3
T3C
T3ST
TOG3
SO
Control
M2
RES
Compare 3/1
Compare 3/2
Control
T3O
Modulator 3
TOG2
T3CO1
T3CO2
T3CM1
T3CM2
I/O-bus
Timer 2
SSI
SSI
Timer 3 consists of an 8-bit up-counter with two compare registers and one capture register. The
timer can be used as event counter, timer and signal generator. Its output can be programmed
as modulator and demodulator for the serial interface. The two compare registers enable various
modes of signal generation, modulation and demodulation. The counter can be driven by internal and external clock sources. For external clock sources, it has a programmable edgesensitive input which can be used as counter input, capture signal input or trigger input. This
timer input is synchronized with SYSCL. Therefore, in the power-down mode SLEEP (CPU core
→sleep and OSC-Stop →yes), this timer input is stopped too. The counter is readable via its
capture register while it is running. In capture mode, the counter value can be captured by a programmable capture event from the Timer 3 input or Timer 2 output.
47
4680C–4BMCU–01/05
A special feature of this timer is the trigger- and single-action mode. In trigger mode, the counter
starts counting triggered by the external signal at its input. In single-action mode, the counter
counts only one time up to the programmed compare match event. These modes are very useful
for modulation, demodulation, signal generation, signal measurement and phase control. For
phase control, the timer input is protected against negative voltages and has zero-cross detection capability.
Timer 3 has a modulator output stage and input functions for demodulation. As modulator it
works together with Timer 2 or the serial interface. When the shift register is used for modulation
the data shifted out of the register is encoded bit-wise. In all demodulation modes, the decoded
data bits are shifted automatically into the shift register.
Figure 5-25. Counter 3 Stage
TOG2
T3I
T3EIM
INT5
Control
Capture register
D
NQ
CL3
8-bit counter
T3SM1
T3RM1
T3IM1
T3TM1
: T3M1
RES
CM31
8-bit comparator
Control
TOG3
C31
C32
CM32
Compare register 1
NQ
D
T3SM2
T3RM2
T3IM2
T3TM2
: T3M2
Compare register 2
5.3.3.2
Timer/Counter Modes
Timer 3 has 6 timer modes and 6 modulator/demodulator modes. The mode is set via the Timer
3 Mode Register T3M.
In all these modes, the compare register and the compare-mode register belonging to it define
the counter value for a compare match and the action of a compare match. A match of the current counter value with the content of one compare register triggers a counter reset, a Timer 3
interrupt or the toggling of the output flip-flop. The compare mode registers T3M1 and T3M2
contain the mask bits for enabling or disabling these actions.
The counter can also be enabled to execute single actions with one or both compare registers. If
this mode is set the corresponding compare match event is generated only once after the
counter starts.
48
ATAM893-D
4680C–4BMCU–01/05
ATAM893-D
Most of the timer modes use their compare registers alternately. After the start has been activated, the first comparison is carried out via the compare register 1, the second is carried out via
the compare register 2, the third is carried out again via the compare register 1 and so on. This
makes it easy to generate signals with constant periods and variable duty cycle or to generate
signals with variable pulse and space widths.
If single-action mode is set for one compare register, the comparison is always carried out after
the first cycle via the other compare register.
The counter can be started and stopped via the control register T3C. This register also controls
the initial level of the output before start. T3C contains the interrupt mask for a T3I input
interrupt.
Via the Timer 3 clock-select register, the internal or external clock source can be selected. This
register selects also the active edge of the external input. An edge at the external input T3I can
generate also an interrupt if the T3EIM bit is set and the Timer 3 is stopped (T3R = 0) in the T3C
register.
The status of the timer as well as the occurrence of a compare match or an edge detect of the
input signal is indicated by the status register T2ST. This allows identification of the interrupt
source because all these events share only one timer interrupt.
Timer 3 compares data values.
The Timer 3 has two 8-bit compare registers (T3CO1, T3CO2). The compare data value can be
‘m’ for each of the Timer 3 compare registers.
The compare data value for the compare registers is:
0 ≤x ≤255
m = x +1
Timer 3 – Mode 1: Timer/Counter
The selected clock from an internal or external source increments the 8-bit counter. In this mode,
the timer can be used as event counter for external clocks at T3I or as timer for generating interrupts and pulses at T3O. The counter value can be read by the software via the capture register.
Figure 5-26. Counter Reset with Each Compare Match
T3R
0
0
0
1
2
3
0
1
2
3
4
5
0
1
2
3
0
1
2
3
Counter 3
CM31
CM32
INT5
T3O
49
4680C–4BMCU–01/05
Figure 5-27. Counter Reset with Compare Register 2 and Toggle with Start
CL3
T3R
0
0
0
1
2
3
4
5
6
7
8
9
0
1
2
3
4
5
6
Counter 3
CM31
CM32
INT5
T3O
Toggle
by start
T3O
Figure 5-28. Single Action of Compare Register 1
T3R
0 0 1 2 3 4 5 6 7 8 9 10 0 1 2 0 1 2 0 1 2 0 1 2 0 1 2 0 1 2 0 1 2 0 1 2 0 1 2 0 1
Counter 3
CM31
CM32
T3O
Toggle by start
Timer 3 – Mode 2:
Timer/Counter, External Trigger Restart and External Capture
(with T3I Input)
The counter is driven by an internal clock source. After starting with T3R, the first edge from the
external input T3I starts the counter. The following edges at T3I load the current counter value
into the capture register, reset the counter and restart it. The edge can be selected by the programmable edge decoder of the timer input stage. If single-action mode is activated for one or
both compare registers the trigger signal restarts the single action.
Figure 5-29. Externally Triggered Counter Reset and Start Combined with Single-action Mode
T3R
0 0 0 0 0 0 0 0 1 2 3 4 5 6 7 8 9 10 0 1 2 X X X 0 1 2 3 4 5 6 7 8 9 10 0 1 2 X X X X
Counter 3
T3EX
CM31
CM32
T3O
50
ATAM893-D
4680C–4BMCU–01/05
ATAM893-D
Timer 3 – Mode 3:
Timer/Counter, Internal Trigger Restart and Internal Capture
(with TOG2)
The counter is driven by an internal or external (T3I) clock source. The output toggle signal of
Timer 2 resets the counter. The counter value before the reset is saved in the capture register. If
single-action mode is activated for one or both compare registers, the trigger signal restarts the
single actions. This mode can be used for frequency measurements or as event counter with
time gate (see section “Combination Mode 10”).
Figure 5-30. Event Counter with Time Gate
T3R
T3I
Counter 3
0 0 1 2 3 4 5 6 7 8 910
11
0 1
2
3
4
0 1 2
TOG2
T3CPRegister
Timer 3 – Mode 4:
Capture value = 0
Capture value = 11
Capture value = 4
Timer/Counter
The timer runs as timer/counter in mode 1, but its output T3O is used as output for the Timer 2
output signal.
Timer 3 – Mode 5:
Timer/Counter, External Trigger Restart and External Capture
(with T3I Input)
The Timer 3 runs as timer/counter in mode 2, but its output T3O is used as output for the Timer
2 output signal.
5.3.3.3
Timer 3 Modulator/Demodulator Modes
Timer 3 – Mode 6: Carrier Frequency Burst Modulation Controlled by Timer 2 Output
Toggle Flip–Flop (M2)
The Timer 3 counter is driven by an internal or external clock source. Its compare- and compare
mode registers must be programmed to generate the carrier frequency via the output toggle flipflop. The output toggle flip-flop of Timer 2 is used to enable or disable the Timer 3 output. Timer
2 can be driven by the toggle output signal of Timer 3 or any other clock source (see section
“Combination Mode 11”).
Timer 3 – Mode 7:
Carrier Frequency Burst Modulation Controlled by SSI Internal
Output (SO)
The Timer 3 counter is driven by an internal or external clock source. Its compare- and compare
mode registers must be programmed to generate the carrier frequency via the output toggle flipflop. The output (SO) of the SSI is used to enable or disable the Timer 3 output. The SSI should
be supplied with the toggle signal of Timer 2 (see section “Combination Mode 12”).
51
4680C–4BMCU–01/05
Timer 3 – Mode 8:
FSK Modulation with Shift Register Data (SO)
The two compare registers are used for generating two different time intervals. The SSI internal
data output (SO) selects which compare register is used for the output frequency generation. A
'0' level at the SSI data output enables the compare register 1. A '1' level enables compare register 2. The compare- and compare mode registers must be programmed to generate the two
frequencies via the output toggle flip-flop. The SSI can be supplied with the toggle signal of
Timer 2. The Timer 3 counter is driven by an internal or external clock source. The Timer 2
counter is driven by the Counter 3 (TOG3) (see section “Combination Mode 13”).
Figure 5-31. FSK Modulation
T3R
0 1 2 3 4 0 1 2 3 4 0 1 2 3 4 0 1 2 0 1 2 0 1 2 0 1 2 0 1 2 0 1 2 0 1 2 0 1 2 3 4 0 1
Counter 3
CM31
CM32
0
SO
1
0
T3O
Timer 3 – Mode 9:
Pulse-width Modulation with the Shift Register
The two compare registers are used for generating two different time intervals. The SSI internal
data output (SO) selects which compare register is used for the output pulse generation. In this
mode both compare- and compare mode registers must be programmed for generating the two
pulse widths. It is also useful to enable the single-action mode for extreme duty cycles. Timer 2
is used as baud-rate generator and for the trigger restart of Timer 3. The SSI must be supplied
with a toggle signal of Timer 2. The counter is driven by an internal or external clock source (see
section “Combination Mode 7”).
Figure 5-32. Pulse-width Modulation
TOG2
SIR
SO
0
1
0
1
SCO
T3R
Counter 3
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 2 3 4 5 6 7 8 9101112131415 0 1 2 3 4 5 6 7 8 9101112131415 0 1 2 3 4
CM31
CM32
T3O
52
ATAM893-D
4680C–4BMCU–01/05
ATAM893-D
Timer 3 – Mode 10: Manchester Demodulation/Pulse-width Demodulation
For Manchester demodulation, the edge detection stage must be programmed to detect each
edge at the input. These edges are evaluated by the demodulator stage. The timer stage is used
to generate the shift clock for the SSI. The compare register 1 match event defines the correct
moment for shifting the state from the input T3I as the decoded bit into shift register - after that
the demodulator waits for the next edge to synchronize the timer by a reset for the next bit. The
compare register 2 can also be used to detect a time-out error and handle it with an interrupt
routine (see section “Combination Mode 8”).
Figure 5-33. Manchester Demodulation
Timer 3
mode
T3I
Synchronize
1
Manchester demodulation mode
0
1
1
1
0
0
1
1
0
T3EX
SI
CM31 = SCI
1
1
1
0
0
1
1
BIT 0
BIT 1
BIT 2
BIT 3
BIT 4
BIT 5
BIT 6
SR DATA
0
Timer 3 – Mode 11: Bi-phase Demodulation
In the Bi-phase demodulation mode, the timer operates like in Manchester demodulation mode.
The difference is that the bits are decoded via a toggle flip-flop. This flip-flop samples the edge in
the middle of the bit-frame and the compare register 1 match event shifts the toggle flip-flop output into a shift register (see section “Combination Mode 9”).
Figure 5-34. Bi-phase Demodulation
Timer 3
mode
T3I
Synchronize
0
Biphase demodulation mode
0
1
0
1
0
1
0
1
T3EX
Q1 = SI
CM31 = SCI
Reset
Counter 3
SR-DATA
0
1
1
0
1
0
1
BIT 0
BIT 1
BIT 2
BIT 3
BIT 4
BIT 5
BIT 6
0
53
4680C–4BMCU–01/05
Timer 3 – Mode 12: Timer/Counter with External Capture Mode (T3I)
The counter is driven by an internal clock source and an edge at the external input T3I loads the
counter value into the capture register. The edge can be selected with the programmable edge
detector of the timer input stage. This mode can be used for signal and pulse measurements.
Figure 5-35. External Capture Mode
T3R
T3I
Counter 3
0 0 1 2 3 4 5 6 7 8 9 10 11 1213 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41
T3CPRegister
5.3.3.4
Capture value = 35
Capture value = 17
Capture value = X
Timer 3 Modulator for Carrier Frequency Burst Modulation
If the output stage operates as pulse-width modulator for the shift register the output can be
stopped with stage 1 of Timer 2. For this task, the timer mode 3 must be used and the prescaler
must be supplied by the internal shift clock of the shift register.
The modulator can be started with the start of the shift register (SIR = 0) and stopped either by a
shift register stop (SIR = 1) or compare match event of stage 1 of Timer 2. For this task, the
Timer 2 must be used in mode 3 and the prescaler stage must be supplied by the internal shift
clock of the shift register.
Figure 5-36. Modulator 3
0
T3
TOG3
Set
M3
1
Res
T3TOP
2
MUX
3
SSI/
Control
T3O
Timer 3 Mode
6
7
9
other
SO
M2
T3O
MUX 1
MUX 2
MUX 3
MUX 0
OMSK
T3M
54
ATAM893-D
4680C–4BMCU–01/05
ATAM893-D
5.3.3.5
Timer 3 Demodulator for Bi-phase, Manchester and Pulse-width-modulated Signals
The demodulator stage of Timer 3 can be used to decode Bi-phase, Manchester and pulsewidth-coded signals
Figure 5-37. Timer 3 Demodulator 3
T3M
SCI
T3I
Demodulator 3
T3EX
SI
Res
CM31
Counter 3
Reset
Counter 3
Control
5.3.3.6
Timer 3 Registers
5.3.3.7
Timer 3 Mode Register (T3M)
Address: 'B'hex — Subaddress: '0'hex
Bit 3
Bit 2
Bit 1
Bit 0
T3M3
T3M2
T3M1
T3M0
T3M3
Timer 3 Mode select bit 3
T3M2
Timer 3 Mode select bit 2
T3M1
Timer 3 Mode select bit 1
T3M0
Timer 3 Mode select bit 0
Table 5-13.
Reset value: 1111b
Timer 3 Mode Select Bits
Mode
T3M3
T3M2
T3M1
T3M0
1
1
1
1
1
Timer/counter with a read access
2
1
1
1
0
Timer/counter, external capture and external trigger
restart mode (T3I)
3
1
1
0
1
Timer/counter, internal capture and internal trigger
restart mode (TOG2)
4
1
1
0
0
Timer/counter mode 1 without output
(T2O →T3O)
5
1
0
1
1
Timer/counter mode 2 without output
(T2O →T3O)
6
1
0
1
0
Burst modulation with Timer 2 (M2)
7
Note:
Timer 3 Modes
1
0
0
1
Burst modulation with shift register (SO)
1. In this mode, the SSI can be used only as demodulator (8-bit NRZ rising edge). All other SSI
modes are not allowed.
55
4680C–4BMCU–01/05
Table 5-13.
Mode
T3M3
T3M2
T3M1
T3M0
8
1
0
0
0
FSK modulation with shift register (SO)
9
0
1
1
1
Pulse-width modulation with shift register (SO) and
Timer 2 (TOG2), internal trigger restart (SCO) →counter
reset
10
0
1
1
0
Manchester demodulation/pulse-width demodulation(1)
(T2O →T3O)
11
0
1
0
1
Bi-phase demodulation(1) (T2O →T3O)
12
0
1
0
0
Timer/counter with external capture mode (T3I)
13
0
0
1
1
Not allowed
14
0
0
1
0
Not allowed
15
0
0
0
1
Not allowed
16
Note:
5.3.3.8
Timer 3 Mode Select Bits (Continued)
Timer 3 Modes
0
0
0
0
Not allowed
1. In this mode, the SSI can be used only as demodulator (8-bit NRZ rising edge). All other SSI
modes are not allowed.
Timer 3 Control Register 1 (T3C) Write
Primary register address: 'C'hex — Write
Write
Bit 2
Bit 1
Bit 0
T3EIM
T3TOP
T3TS
T3R
Reset value: 0000b
T3EIM
Timer 3 Edge Interrupt Mask
T3EIM = 0, disables the interrupt when an edge event for Timer 3 occurs (T3I)
T3EIM = 1, enables the interrupt when an edge event for Timer 3 occurs (T3I)
T3TOP
Timer 3 Toggle Output Preset T3TOP = 0, sets toggle output (M3) to '0'
............. ...... T3TOP = 1, sets toggle output (M3) to '1'
............. ...... Note: If T3R = 1, no output preset is possible
T3TS
Timer 3 Toggle with Start . T3TS = 0, Timer 3 output is not toggled during the start
...... ...... T3TS = 1, Timer 3 output is toggled if started with T3R
T3R
56
Bit 3
Timer 3 Run
...... ...... T3R = 0, Timer 3 stop and reset
...... ...... T3R = 1, Timer 3 run
ATAM893-D
4680C–4BMCU–01/05
ATAM893-D
5.3.3.9
Timer 3 Status Register 1 (T3ST) Read
Primary register address: 'C'hex — Read
Read
Bit 2
Bit 1
Bit 0
---
T3ED
T3C2
T3C1
Reset value: x000b
T3ED
Timer 3 Edge Detect
This bit will be set by the edge-detect logic of Timer 3 input (T3I)
T3C2
Timer 3 Compare 2
This bit will be set when a match occurs between Counter 3 and T3CO2
T3C1
Timer 3 Compare 1
This bit will be set when a match occurs between Counter 3 and T3CO1
Note:
5.3.3.10
Bit 3
The status bits T3C1, T3C2 and T3ED will be reset after a READ access to T3ST.
Timer 3 Clock Select Register (T3CS)
Address: 'B'hex — Subaddress: '1'hex
T3CS
Bit 3
Bit 2
Bit 1
Bit 0
T3E1
T3E0
T3CS1
T3CS0
T3E1
Timer 3 Edge select bit 1
T3E0
Timer 3 Edge select bit 0
Table 5-14.
External Input Edge Select Bits
T3E1
T3E0
1
1
---
1
0
Positive edge at T3I pin
0
1
Negative edge at T3I pin
0
0
Each edge at T3I pin
Timer 3 Input Edge Select (T3I)
T3CS1
Timer 3 Clock Source select bit 1
T3CS0
Timer 3 Clock Source select bit 0
Table 5-15.
Reset value: 1111b
Select Clock Source Bits
T3CS1
TCS0
Counter 3 Input Signal (CL3)
1
1
System clock (SYSCL)
1
0
Output signal of Timer 2 (POUT)
0
1
Output signal of Timer 1 (T1OUT)
0
0
External input signal from T3I edge detect
57
4680C–4BMCU–01/05
5.3.3.11
Timer 3 Compare- and Compare Mode Register
Timer 3 has two separate compare registers T3CO1 and T3CO2 for the 8-bit stage of Timer 3.
The timer compares the content of the compare register with the current counter value. If both
match, it generates a signal. This signal can be used for the counter reset, to generate a timer
interrupt, for toggling the output flip-flop, as SSI clock or as clock for the next counter stage. For
each compare register, a compare-mode register exists. These registers contain mask bits to
enable or disable the generation of an interrupt, a counter reset, or an output toggling with the
occurrence of a compare match of the corresponding compare register. The mask bits for activating the single-action mode can also be located in the compare mode registers. When
assigned to the compare register a compare event will be suppressed.
5.3.3.12
Timer 3 Compare Mode Register 1 (T3CM1)
Address: 'B'hex — Subaddress: '2'hex
T3CM1
Bit 3
Bit 2
Bit 1
Bit 0
T3SM1
T3TM1
T3RM1
T3IM1
Reset value: 0000b
T3SM1
Timer 3 Single action Mask bit 1
T3SM1 = 0, disables single-action compare mode
T3SM1 = 1, enables single-compare mode. After this bit is set, the compare
register (T3CO1) is used until the next compare match
T3TM1
Timer 3 compare Toggle action Mask bit 1
T3TM1 = 0, disables compare toggle
T3TM1 = 1, enables compare toggle. A match of Counter 3 with the compare
register (T3CO1) toggles the output flip-flop (TOG3)
T3RM1
Timer 3 Reset Mask bit 1
T3RM1 = 0, disables counter reset
T3RM1 = 1, enables counter reset. A match of Counter 3 with the compare
register (T3CO1) resets the Counter 3
T3IM1
Timer 3 Interrupt Mask bit 1
T3RM1 = 0, disables Timer 3 interrupt for T3CO1 register
T3RM1 = 1, enables Timer 3 interrupt for T3CO1 register
T3CM1 contains the mask bits for the match event of the Counter 3 compare register 1
58
ATAM893-D
4680C–4BMCU–01/05
ATAM893-D
5.3.3.13
Timer 3 Compare Mode Register 2 (T3CM2)
Address: 'B'hex — Subaddress: '3'hex
T3CM2
Bit 3
Bit 2
Bit 1
Bit 0
T3SM2
T3TM2
T3RM2
T3IM2
Reset value: 0000b
T3SM2
Timer 3 Single action Mask bit 2
T3SM2 = 0, disables single-action compare mode
T3SM2 = 1, enables single-compare mode. After this bit is set, the compare
register (T3CO2) is used until the next compare match
T3TM2
Timer 3 compare Toggle action Mask bit 2
T3TM2 = 0, disables compare toggle
T3TM2 = 1, enables compare toggle. A match of Counter 3 with the compare
register (T3CO2) toggles the output flip-flop (TOG3)
T3RM2
Timer 3 Reset Mask bit 2
T3RM2 = 0, disables counter reset
T3RM2 = 1, enables counter reset. A match of Counter 3 with the compare
register (T3CO2) resets the Counter 3
T3IM2
Timer 3 Interrupt Mask bit 2
T3RM2 = 0, disables Timer 3 interrupt for T3CO2 register
T3RM2 = 1, enables Timer 3 interrupt for T3CO2 register
T3CM2 contains the mask bits for the match event of Counter 3 compare register 2
The compare registers and corresponding counter reset masks can be used to program the
counter time intervals and the toggle masks can be used to program the output signal. The single-action mask can also be used in this mode. It starts operating after the timer started with
T3R.
5.3.3.14
Timer 3 COmpare Register 1 (T3CO1) Byte Write
Address: 'B'hex — Subaddress: '4'hex
High Nibble
Second write cycle
Bit 7
Bit 6
First write cycle
Bit 3
Bit 2
Bit 5
Bit 4
Reset value: 1111b
Bit 0
Reset value: 1111b
Low Nibble
5.3.3.15
Bit 1
Timer 3 COmpare Register 2 (T3CO2) Byte Write
Address: 'Beaux — Subaddress: '5'hex
High Nibble
Second write cycle
Bit 7
Bit 6
Bit 5
Bit 4
Reset value: 1111b
Bit 0
Reset value: 1111b
Low Nibble
First write cycle
Bit 3
Bit 2
Bit 1
59
4680C–4BMCU–01/05
5.3.3.16
Timer 3 Capture Register
The counter content can be read via the capture register. There are two ways to use the capture
register. In modes 1 and 4, it is possible to read the current counter value directly out of the capture register. In the capture modes 2, 3, 5 and 12, a capture event like an edge at the Timer 3
input or a signal from Timer 2 stores the current counter value into the capture register. This
counter value can be read from the capture register.
5.3.3.17
Timer 3 CaPture Register (T3CP) Byte Read
Address: 'Beaux — Subaddress: '4'hex
High Nibble
First read cycle
Bit 7
Bit 6
Bit 5
Bit 4
Reset value: xxxxb
Bit 0
Reset value: xxxxb
Low Nibble
Second read cycle
5.3.4
5.3.4.1
Bit 3
Bit 2
Bit 1
Synchronous Serial Interface (SSI)
SSI Features
• 2- and 3-wire NRZ
• 2-wire mode (MCL compatible), additional internal 2-wire link for multi-chip
packaging solutions
• With Timer 2
– Bi-phase modulation
– Manchester modulation
– Pulse-width demodulation
– Burst modulation
• With Timer 3
– Pulse-width modulation (PWM)
– FSK modulation
– Bi-phase demodulation
– Manchester demodulation
– Pulse-width demodulation
– Pulse position Demodulation
60
ATAM893-D
4680C–4BMCU–01/05
ATAM893-D
5.3.4.2
SSI Peripheral Configuration
The synchronous serial interface (SSI) can be used either for serial communication with external
devices such as Proems, shift registers, display drivers, other microcontrollers, or as a means
for generating and capturing on-chip serial streams of data. External data communication takes
place via the Port 4 (BP4), a multi-functional port which can be software configured by writing
the appropriate control word into the P4CR register. The SSI can be configured in any of the following ways:
1. 2-wire external interface for bi-directional data communication with one data terminal
and one shift clock. The SSI uses the Port BP43 as a bi-directional serial data line (SD)
and BP40 as shift clock line (SC).
2. 3-wire external interface for simultaneous input and output of serial data, with a serial
input data terminal (SI), a serial output data terminal (SO) and a shift clock (SC). The
SSI uses BP40 as shift clock (SC), while the serial data input (SI) is applied to BP43
(configured in P4CR as input!). Serial output data (SO) in this case is passed through to
BP42 (configured in P4CR to T2O) via the Timer 2 output stage (T2M2 configured in
mode 6).
3. Timer/SSI combined modes - the SSI used together with Timer 2 or Timer 3 is capable
of performing a variety of data modulation and demodulation functions (see Timer Section). The modulating data is converted by the SSI into a continuous serial stream of
data which is in turn modulated in one of the timer functional blocks. Serial demodulated data can be serially captured in the SSI and read by the controller. In the Timer 3
modes 10 and 11 (demodulation modes) the SSI can only be used as demodulator.
4. Multi-chip link (MCL) – the SSI can also be used as an microchip data interface for use
in single package multi-chip modules or hybrids. For such applications, the SSI is provided with two dedicated pads (MCL_SD and MCL_SC) which act as a two-wire chipto-chip link. The MCL can be activated by the MCL control bit. Should these MCL pads
be used by the SSI, the standard SD and SC pins are not required and the corresponding Port 4 ports are available as conventional data ports.
Figure 5-38. Block Diagram of the Synchronous Serial Interface
I/O-bus
Timer 2/Timer 3
SIC1
SIC2
SISC
Control
SC
SO
INT3
SI SCI
SC
SSI-Control
MCL_SC
TOG2
POUT
T1OUT
SYSCL
Output
SO
/2
MSB
8-bit Shift Register
SI
LSB
Shift_CL
STB
MCL_SD
SD
SRB
Receive
Buffer
Transmit
Buffer
I/O-bus
61
4680C–4BMCU–01/05
5.3.4.3
General SSI Operation
The SSI is comprised essentially of an 8-bit shift register with two associated 8-bit buffers the
receive buffer (SRB) for capturing the incoming serial data and a transmit buffer (STB) for intermediate storage of data to be serially output. Both buffers are directly accessible by software.
Transferring the parallel buffer data into and out of the shift register is controlled automatically by
the SSI control, so that both single byte transfers or continuous bit streams can be supported.
The SSI can generate the shift clock (SC) either from one of several on-chip clock sources or
accept an external clock. The external shift clock is output on, or applied to the Port BP40.
Selection of an external clock source is performed by the Serial Clock Direction control bit
(SCD). In the combinational modes, the required clock is selected by the corresponding timer
mode.
The SSI can operate in three data transfer modes - synchronous 8-bit shift mode, MCL compatible 9-bit shift modes or 8-bit pseudo MCL protocol (without acknowledge-bit).
External SSI clocking is not supported in these modes. The SSI should thus generate and has
full control over the shift clock so that it can always be regarded as an MCL Bus Master device.
All directional control of the external data port used by the SSI is handled automatically and is
dependent on the transmission direction set by the Serial Data Direction (SDD) control bit. This
control bit defines whether the SSI is currently operating in Transmit (TX) mode or Receive (RX)
mode.
Serial data is organized in 8-bit telegrams which are shifted with the most significant bit first. In
the 9-bit MCL mode, an additional acknowledge bit is appended to the end of the telegram for
handshaking purposes (see section “MCL Protocol”).
At the beginning of every telegram, the SSI control loads the transmit buffer into the shift register
and proceeds immediately to shift data serially out. At the same time, incoming data is shifted
into the shift register input. This incoming data is automatically loaded into the receive buffer
when the complete telegram has been received. Thus, data can be simultaneously received and
transmitted if required.
Before data can be transferred, the SSI must first be activated. This is performed by means of
the SSI reset control (SIR) bit. All further operation then depends on the data directional mode
(TX/RX) and the present status of the SSI buffer registers shown by the Serial Interface Ready
Status Flag (SRDY). This SRDY flag indicates the (empty/full) status of either the transmit buffer
(in TX mode), or the receive buffer (in RX mode). The control logic ensures that data shifting is
temporarily halted at any time, if the appropriate receive/transmit buffer is not ready (SRDY = 0).
The SRDY status will then automatically be set back to ‘1’ and data shifting resumed as soon as
the application software loads the new data into the transmit register (in TX mode) or frees the
shift register by reading it into the receive buffer (in RX mode).
Another activity status (ACT) bit indicates the present status of the serial communication. The
ACT bit remains high for the duration of the serial telegram or if MCL stop or start conditions are
currently being generated. Both the current SRDY and ACT status can be read in the SSI status
register. To deactivate the SSI, the SIR bit must be set high.
62
ATAM893-D
4680C–4BMCU–01/05
ATAM893-D
5.3.4.4
8-bit Synchronous Mode
Figure 5-39. 8-bit Synchronous Mode
SC
(rising edge)
SC
(falling edge)
0
DATA
SD/TO2
0
1
1
0
1
0
Bit 7
0
Bit 7
1
Bit 0
0
1
1
0
1
0
1
Bit 0
Data: 00110101
In the 8-bit synchronous mode, the SSI can operate as either a 2- or 3-wire interface (see section “SSI Peripheral Configuration”). The serial data (SD) is received or transmitted in NRZ
format, synchronized to either the rising or falling edge of the shift clock (SC). The choice of
clock edge is defined by the Serial Mode Control bits (SM0,SM1). It should be noted that the
transmission edge refers to the SC clock edge with which the SD changes. To avoid clock skew
problems, the incoming serial input data is shifted in with the opposite edge.
When used together with one of the timer modulator or demodulator stages, the SSI must be set
in the 8-bit synchronous mode 1.
In RX mode, as soon as the SSI is activated (SIR = 0), 8 shift clocks are generated and the
incoming serial data is shifted into the shift register. This first telegram is automatically transferred into the receive buffer and the SRDY set to 0 indicating that the receive buffer contains
valid data. At the same time an interrupt (if enabled) is generated. The SSI then continues shifting in the following 8-bit telegram. If, during this time the first telegram has been read by the
controller, the second telegram will also be transferred in the same way into the receive buffer
and the SSI will continue clocking in the next telegram. Should, however, the first telegram not
have been read (SRDY = 1), then the SSI will stop, temporarily holding the second telegram in
the shift register until a certain point of time when the controller is able to service the receive
buffer. In this way no data is lost or overwritten.
Deactivating the SSI (SIR = 1) in mid-telegram will immediately stop the shift clock and latch the
present contents of the shift register into the receive buffer. This can be used for clocking in a
data telegram of less than 8 bits in length. Care should be taken to read out the final complete
8-bit data telegram of a multiple word message before deactivating the SSI (SIR = 1) and terminating the reception. After termination, the shift register contents will overwrite the receive
buffer.
63
4680C–4BMCU–01/05
Figure 5-40. Example of an 8-bit Synchronous Transmit Operation
SC
msb
lsb
7 6 5 4 3 2 1
SD
msb
0
lsb msb
lsb
7 6 5 4 3 2 1 0 7 6 5 4 3 2 1
tx data 1
tx data 2
0
tx data 3
SIR
SRDY
ACT
Interrupt
(IFN = 0)
Interrupt
(IFN = 1)
Write STB
(tx data 1)
Write STB
(tx data 2)
Write STB
(tx data 3)
Figure 5-41. Example of an 8-bit Synchronous Receive Operation
SC
msb
SD
lsb
msb
lsb
msb
7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0
rx data 1
lsb
7 6 5 4 3 2 1 0 7 6 5 4
rx data 2
rx data 3
SIR
SRDY
ACT
Interrupt
(IFN = 0)
Interrupt
(IFN = 1)
Read SRB
(rx data 1)
64
Read SRB
(rx data 2)
Read SRB
(rx data 3)
ATAM893-D
4680C–4BMCU–01/05
ATAM893-D
5.3.4.5
9-bit Shift Mode
In the 9-bit shift mode, the SSI is able to handle the MCL protocol (described below). It always
operates as an MCL master device, i.e., SC is always generated and output by the SSI. Both the
MCL start and stop conditions are automatically generated whenever the SSI is activated or
deactivated by the SIR bit. In accordance with the MCL protocol, the output data is always
changed in the clock low phase and shifted in on the high phase.
Before activating the SSI (SIR = 0) and commencing an MCL dialog, the appropriate data direction for the first word must be set using the SDD control bit. The state of this bit controls the
direction of the data port (BP43 or MCL_SD). Once started, the 8 data bits are, depending on
the selected direction, either clocked into or out of the shift register. During the 9th clock period,
the port direction is automatically switched over so that the corresponding acknowledge bit can
be shifted out or read in. In transmit mode, the acknowledge bit received from the slave device is
captured in the SSI Status Register (TACK) where it can be read by the controller. In receive
mode, the state of the acknowledge bit to be returned to the slave device is predetermined by
the SSI Status Register (RACK).
Changing the directional mode (TX/RX) should not be performed during the transfer of an MCL
telegram. One should wait until the end of the telegram which can be detected using the SSI
interrupt (IFN = 1) or by interrogating the ACT status.
Once started, a 9-bit telegram will always run to completion and will not be prematurely terminated by the SIR bit. So, if the SIR bit is set to ‘1’ in telegram, the SSI will complete the current
transfer and terminate the dialog with an MCL stop condition.
Figure 5-42. Example of MCL Transmit Dialog
Start
Stop
SC
msb
SD
lsb
7 6 5 4 3 2 1 0 A
msb
lsb
7 6 5 4 3 2 1 0 A
tx data 1
tx data 2
SRDY
ACT
Interrupt
(IFN = 0)
Interrupt
(IFN = 1)
SIR
SDD
Write STB
(tx data 1)
Write STB
(tx data 2)
65
4680C–4BMCU–01/05
Figure 5-43. Example of MCL Receive Dialog
Start
Stop
SC
msb
SD
lsb
7 6 5 4 3 2 1 0 A
tx data 1
msb
lsb
7 6 5 4 3 2 1 0 A
rx data 2
SRDY
ACT
Interrupt
(IFN = 0)
Interrupt
(IFN = 1)
SIR
SDD
Write STB
(tx data 1)
Read SRB
(rx data 2)
5.3.4.6
8-bit Pseudo MCL Mode
In this mode, the SSI exhibits all the typical MCL operational features except for the acknowledge-bit which is never expected or transmitted.
5.3.4.7
MCL Bus Protocol
The MCL protocol constitutes a simple 2-wire bi-directional communication highway via which
devices can communicate control and data information. Although the MCL protocol can support
multi-master bus configurations, the SSI in MCL mode is intended for use purely as a master
controller on a single master bus system. So all reference to multiple bus control and bus contention will be omitted at this point.
All data is packaged into 8-bit telegrams plus a trailing handshaking or acknowledge-bit. Normally the communication channel is opened with a so-called start condition, which initializes all
devices connected to the bus. This is then followed by a data telegram, transmitted by the master controller device. This telegram usually contains an 8-bit address code to activate a single
slave device connected onto the MCL bus. Each slave receives this address and compares it
with its own unique address. The addressed slave device, if ready to receive data, will respond
by pulling the SD line low during the 9th clock pulse. This represents a so-called MCL acknowledge. The controller detecting this affirmative acknowledge then opens a connection to the
required slave. Data can then be passed back and forth by the master controller, each 8-bit telegram being acknowledged by the respective recipient. The communication is finally closed by
the master device and the slave device put back into standby by applying a stop condition onto
the bus.
66
ATAM893-D
4680C–4BMCU–01/05
ATAM893-D
Figure 5-44. MCL Bus Protocol 1
(1)
(2)
(4)
(4)
(3)
(1)
SC
SD
Start
condition
Data
Data
Data
valid
change
valid
Stop
condition
Bus not busy (1)
Both data and clock lines remain HIGH.
Start data transfer (2)
A HIGH to LOW transition of the SD line while the clock (SC)
is HIGH defines a START condition.
Stop data transfer (3)
A LOW to HIGH transition of the SD line while the clock (SC)
is HIGH defines a STOP condition.
Data valid (4)
The state of the data line represents valid data when,
after START condition, the data line is stable for the
duration of the HIGH period of the clock signal.
Acknowledge
All address and data words are serially transmitted to and
from the device in eight-bit words. The receiving device
returns a zero on the data line during the ninth clock cycle to
acknowledge word receipt.
Figure 5-45. MCL Bus Protocol 2
SC
1
SD
5.3.4.8
Start
1st Bit
n
8
8th Bit
9
ACK
Stop
SSI Interrupt
The SSI interrupt INT3 can be generated either by an SSI buffer register status (i.e., transmit
buffer empty or receive buffer full), the end of SSI data telegram or on the falling edge of the
SC/SD pins on Port 4 (see P4CR). SSI interrupt selection is performed by the Interrupt Function
control bit (IFN). The SSI interrupt is usually used to synchronize the software control of the SSI
and inform the controller of the present SSI status. The Port 4 interrupts can be used together
with the SSI or, if the SSI itself is not required, as additional external interrupt sources. In either
case this interrupt is capable of waking the controller out of sleep mode.
To enable and select the SSI relevant interrupts use the SSI interrupt mask (SIM) and the Interrupt Function (IFN) while the Port 4 interrupts are enabled by setting appropriate control bits in
P4CR register.
67
4680C–4BMCU–01/05
5.3.4.9
Modulation and Demodulation
If the shift register is used together with Timer 2 or Timer 3 for modulation or demodulation purposes, the 8-bit synchronous mode must be used. In this case, the unused Port 4 pins can be
used as conventional bi-directional ports.
The modulation and demodulation stages, if enabled, operate as soon as the SSI is activated
(SIR = 0) and cease when deactivated (SIR = 1).
Due to the byte-orientated data control, the SSI (when running normally) generates serial bit
streams which are submultiples of 8 bits. An SSI output masking (OMSK) function permits, however, the generation of bit streams of any length. The OMSK signal is derived indirectly from the
4-bit prescaler of the Timer 2 and masks out a programmable number of unrequited trailing data
bits during the shifting out of the final data word in the bit stream. The number of non-masked
data bits is defined by the value pre-programmed in the prescaler compare register. To use output masking, the modulator stop mode bit (MSM) must be set to’0’ before programming the final
data word into the SSI transmit buffer. This in turn, enables shift clocks to the prescaler when
this final word is shifted out. On reaching the compare value, the prescaler triggers the OMSK
signal and all following data bits are blanked.
5.3.4.10
Internal 2-wire Multi-chip Link
Two additional on-chip pads (MCL_SC and MCL_SD) for the SC and the SD line can be used as
chip-to-chip link for multi-chip applications. These pads can be activated by setting the MCL bit
in the SISC register. They are also used as interface to the internal data EEPROM
Figure 5-46. Multi-chip Link
U505M
SCL
SDA
Multi-chip link
MCL_SC
MCL_SD
V DD
V SS
BP40/SC
BP43/SD
Microcontroller
BP10
BP13
Figure 5-47. SSI Output Masking Function
Timer 2
CL2/1
4-bit counter 2/1
SCL
Compare 2/1
CM1
SO
OMSK
Control
SC
SSI-control
Output
TOG2
POUT
T1OUT
SYSCL
68
SO
/2
SI
MSB
8-bit shift register
LSB
Shift_CL
ATAM893-D
4680C–4BMCU–01/05
ATAM893-D
5.3.4.11
Serial Interface Registers
5.3.4.12
Serial Interface Control Register 1 (SIC1)
Auxiliary register address: '9'hex
Bit 3
Bit 2
Bit 1
Bit 0
SIC1
SIR
SCD
SCS1
SCS0
SIR
Serial Interface Reset
SIR = 1, SSI inactive
SIR = 0, SSI active
SCD
Serial Clock Direction
SCD = 1, SC line used as output
SCD = 0, SC line used as input
Note:
This bit has to be set to '1' during the MCL mode and the Timer 3 mode 10 or 11
SCS1
Serial Clock source Select bit 1
SCS0
Note:
Reset value: 1111b
Serial Clock source Select bit 0
With SCD = '0' the bits SCS1 and SCS0 are insignificant
Table 5-16.
Serial Clock Source Select Bits
SCS1
SCS0
Internal Clock for SSI
1
1
SYSCL/2
1
0
T1OUT/2
0
1
POUT/2
0
0
TOG2/2
• In transmit mode (SDD = 1) shifting starts only if the transmit buffer has been loaded
(SRDY = 1).
• Setting SIR bit loads the contents of the shift register into the receive buffer
(synchronous 8-bit mode only).
• In MCL modes, writing a 0 to SIR generates a start condition and writing a 1 generates a stop
condition.
69
4680C–4BMCU–01/05
5.3.4.13
Serial Interface Control Register 2 (SIC2)
Auxiliary register address: 'A'hex
SIC2
Bit 2
Bit 1
Bit 0
SM1
SM0
SDD
Reset value: 1111b
MSM
Modular Stop Mode
MSM = 1, modulator stop mode disabled (output masking off)
MSM = 0, modulator stop mode enabled (output masking on) - used in modulation modes
for generating bit streams which are not sub multiples of 8 bit.
SM1
Serial Mode control bit 1
SM0
Serial Mode control bit 0
Table 5-17.
Serial Mode Control Bits
Mode
SM1
SM0
1
1
1
8-bit NRZ-data changes with the rising edge of SC
2
1
0
8-bit NRZ-data changes with the falling edge of SC
3
0
1
9-bit two-wire MCL mode
4
0
0
8-bit two-wire pseudo MCL mode (no acknowledge)
SDD
Note:
70
Bit 3
MSM
SSI Mode
Serial Data Direction
SDD = 1, transmit mode – SD line used as output (transmit data). SRDY is set by a
transmit buffer write access
SDD = 0, receive mode – SD line used as input (receive data). SRDY is set by a
receive buffer read access
SDD controls port directional control and defines the reset function for the SRDY-flag
ATAM893-D
4680C–4BMCU–01/05
ATAM893-D
5.3.4.14
Serial Interface Status and Control Register (SISC)
Primary register address: 'Hex
Bit 3
Bit 2
Bit 1
Bit 0
SISC write
MCL
RACK
SIM
IFN
Reset value: 1111b
SISC read
---
TACK
ACT
SRDY
Reset value: xxxxb
MCL
Multi-Chip Link activation
MCL = 1, multi-chip link disabled. This bit has to be set to '0' during
transactions to/from the internal EEPROM
MCL = 0, connects SC and SD, additionally to the internal multi-chip link pads
RACK
Receive ACKnowledge status/control bit for MCL mode
RACK = 0, transmit acknowledge in next receive telegram
RACK = 1, transmit no acknowledge in last receive telegram
TACK
Transmit ACKnowledge status/control bit for MCL mode
TACK = 0, acknowledge received in last transmit telegram
TACK = 1, no acknowledge received in last transmit telegram
SIM
Serial Interrupt Mask
SIM = 1, disable interrupts
SIM = 0, enable serial interrupt. An interrupt is generated
IFN
Interrupt FuNction
IFN = 1, the serial interrupt is generated at the end of telegram
IFN = 0, the serial interrupt is generated when the SRDY goes low (i.e., buffer
becomes empty/full in transmit/receive mode)
SRDY
Serial interface buffer ReaDY status flag
SRDY = 1, in receive mode: receive buffer empty
in transmit mode: transmit buffer full
SRDY = 0, in receive mode: receive buffer full
in transmit mode: transmit buffer empty
ACT
Transmission ACTive status flag
ACT = 1, transmission is active, i.e., serial data transfer. Stop or start conditions
are currently in progress.
ACT = 0, transmission is inactive
71
4680C–4BMCU–01/05
5.3.4.15
Serial Transmit Buffer (STB) – Byte Write
Primary register address: '9'hex
First write cycle
Bit 3
Bit 2
Bit 1
Bit 0
Reset value: xxxxb
Second write cycle
Bit 7
Bit 6
Bit 5
Bit 4
Reset value: xxxxb
The STB is the transmit buffer of the SSI. The SSI transfers the transmit buffer into the shift register and
starts shifting with the most significant bit.
5.3.4.16
Serial Receive Buffer (SRB) – Byte Read
Primary register address: '9'hex
First read cycle
Bit 7
Bit 6
Bit 5
Bit 4
Reset value: xxxxb
Second read cycle
Bit 3
Bit 2
Bit 1
Bit 0
Reset value: xxxxb
The SRB is the receive buffer of the SSI. The shift register clocks serial data in (most significant bit first)
and the loads content into the receive buffer when the complete telegram has been received.
5.3.5
Combination Modes
The UTCM consists of two timers (Timer 2 and Timer 3) and a serial interface. There is a multitude of modes in which the timers and serial interface can work together.
The 8-bit wide serial interface operates as shift register for modulation and demodulation. The
modulator and demodulator units work together with the timers and shift the data bits into or out
of the shift register.
72
ATAM893-D
4680C–4BMCU–01/05
ATAM893-D
5.3.5.1
Combination Mode Timer 2 and SSI
Figure 5-48. Combination Timer 2 and SSI
I/O-bus
P4CR
T2M1
T2M2
T2I
DCGO
SYSCL
T1OUT
TOG3
SCL
CL2/1
4-bit Counter 2/1
RES
T2C
T2O
CL2/2
OVF1
POUT
Compare 2/1
8-bit Counter 2/2
DCG
RES
Timer 2 - control
OUTPUT
OVF2
TOG2
Compare 2/2
MOUT
INT4
POUT
Bi-phase
Manchester
modulator
CM1
T2CO1
T2CM
T2CO2
Timer 2
modulator
output-stage
TOG2
SO
Control
I/O-bus
SIC1
SIC2
SISC
Control
TOG2
POUT
T1OUT
SYSCL
SO
INT3
SCLI
SC
SSI-control
MCL_SC
Output
SCL
SO
MCL_SD
SI
Shift_CL
MSB
8-bit shift register
SD
LSB
SRB
STB
Receive
buffer
Transmit
buffer
I/O-bus
Combination Mode 1: Burst Modulation
SSI mode 1:
Timer 2 mode 1, 2, 3 or 4:
Timer 2 output mode 3:
8-bit NRZ and internal data SO output to the Timer 2 modulator
stage
8-bit compare counter with 4-bit programmable prescaler and
DCG
Duty cycle burst generator
Figure 5-49. Carrier Frequency Burst Modulation with the SSI Internal Data Output
DCGO
1 2 0 1 2 0 1 2 0 1 2 0 1 2 0 1 2 0 1 2 0 1 2 0 1 2 0 1 2 0 1 2 0 1 2 0 1 2 0 1
Counter 2
Counter = compare register (= 2)
TOG2
SO
Bit 0
Bit 1
Bit 2
Bit 3
Bit 4
Bit 5
Bit 6
Bit 7
Bit 8
Bit 9
Bit 10
Bit 11
Bit 12
Bit 13
T2O
73
4680C–4BMCU–01/05
Combination Mode 2: Bi-phase Modulation 1
SSI mode 1:
8-bit shift register internal data output (SO) to the Timer 2
modulator stage
8-bit compare counter with 4-bit programmable prescaler
The modulator 2 of Timer 2 modulates the SSI internal
data output to Bi-phase code
Timer 2 mode 1, 2, 3 or 4:
Timer 2 output mode 4:
Figure 5-50. Bi-phase Modulation 1
TOG2
SC
8-bit SR-data
0
SO
0
1
1
0
1
0
1
Bit 7
Bit 0
0
T2O
0
1
1
0
1
0
1
Data: 00110101
Combination Mode 3: Manchester Modulation 1
SSI mode 1:
8-bit shift register internal data output (SO) to the Timer 2
modulator stage
8-bit compare counter with 4-bit programmable prescaler
The modulator 2 of Timer 2 modulates the SSI internal data
output to Manchester code
Timer 2 mode 1, 2, 3 or 4:
Timer 2 output mode 5:
Figure 5-51. Manchester Modulation 1
TOG2
SC
8-bit SR-data
0
SO
0
1
1
0
1
0
1
Bit 7
T2O
0
Bit 0
0
Bit 7
1
1
0
1
0
1
Bit 0
Data: 00110101
74
ATAM893-D
4680C–4BMCU–01/05
ATAM893-D
Combination Mode 4: Manchester Modulation 2
SSI mode 1:
8-bit shift register internal data output (SO) to the Timer 2
modulator stage
8-bit compare counter and 4-bit prescaler
The modulator 2 of Timer 2 modulates the SSI data output to
Manchester code
Timer 2 mode 3:
Timer 2 output mode 5:
The 4-bit stage can be used as prescaler for the SSI to generate the stop signal for modulator 2.
The SSI has a special mode to supply the prescaler with the shift clock. The control output signal
(OMSK) of the SSI is used as stop signal for the modulator. This is an example for a 12-bit
Manchester telegram:
Figure 5-52. Manchester Modulation 2
SCLI
Buffer full
SIR
Bit 7 Bit 6
SO
Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
SC
MSM
Timer 2
Mode 3
SCL
Counter 2/1
0
0
0
0
0
Counter 2/1 = Compare Register 2/1 (= 4)
0
0
0
0
1
2
3
4
0
1
2
3
OMSK
T2O
Combination Mode 5: Bi-phase Modulation 2
SSI mode 1:
Timer 2 mode 3:
Timer 2 output mode 4:
8-bit shift register internal data output (SO) to the Timer 2
modulator stage
8-bit compare counter and 4-bit prescaler
The modulator 2 of Timer 2 modulates the SSI data output
to Bi-phase code
The 4-bit stage can be used as prescaler for the SSI to generate the stop signal for modulator 2.
The SSI has a special mode to supply the prescaler via the shift clock. The control output signal
(OMSK) of the SSI is used as a stop signal for the modulator. This is an example for a 13-bit Biphase telegram.
75
4680C–4BMCU–01/05
Figure 5-53. Bi-phase Modulation 2
SCLI
Buffer full
SIR
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
SO
SC
MSM
Timer 2
Mode 3
SCL
0
Counter 2/1
0
0
0
Counter 2/1 = Compare Register 2/1 (= 5)
0
0
0
0
1
2
3
0
4
5
0
1
2
OMSK
T2O
5.3.5.2
Combination Mode Timer 3 and SSI
Figure 5-54. Combination Timer 3 and SSI
I/O-bus
T3CS
T3M
T3I
SC
T3EX
T3I
T3EX
SYSCL
T1OUT
POUT
CL3
CM31
CP3
T3CP
Demodulator 3
SI
RES
8-bit Counter 3
T3C
INT5
T3ST
TOG3
SO
Control
RES
Compare 3/1
Compare 3/2
T3CO1
T3CO2
Timer 3 - control
T3CM1
T3O
Modulator 3
M2
T3CM2
SI
SC
SIC1
TOG2
POUT
T1OUT
SYSCL
SIC2
SISC
Control
INT3
SCLI
SC
SSI-control
MCL_SC
Output
SO
Shift_CL
MSB
8-bit shift register
STB
Transmit buffer
76
SI
MCL_SD
SI
LSB
SRB
I/O-bus
Receive buffer
ATAM893-D
4680C–4BMCU–01/05
ATAM893-D
Combination Mode 6: FSK Modulation
SSI mode 1:
Timer 3 mode 8:
8-bit shift register internal data output (SO) to the Timer 3
FSK modulation with shift register data (SO)
The two compare registers are used to generate two varied time intervals. The SSI data output
selects which compare register is used for the output frequency generation. A '0'-level at the SSI
data output enables the compare register 1 and a '1'-level enables the compare register 2. The
compare and compare mode registers must be programmed to generate the two frequencies via
the output toggle flip-lop. The SSI can be supplied with the toggle signal of Timer 2 or any other
clock source. The Timer 3 counter is driven by an internal or external clock source.
Figure 5-55. FSK Modulation 1
T3R
0 1 2 3 4 0 1 2 3 4 0 1 2 3 4 0 1 2 0 1 2 0 1 2 0 1 2 0 1 2 0 1 2 0 1 2 0 1 2 3 4 0 1
Counter 3
CM31
CM32
SO
0
1
0
T3O
Combination Mode 7: Pulse-width Modulation (PWM)
SSI mode 1:
8-bit shift register internal data output (SO) to the Timer 3
Timer 3 mode 9:
Pulse-width modulation with the shift register data (SO)
The two compare registers are used to generate two varied time intervals. The SSI data output
selects which compare register is used for the output pulse generation. In this mode, both compare and compare mode registers must be programmed to generate the two pulse width. It is
also useful to enable the single-action mode for extreme duty cycles. Timer 2 is used as baudrate generator and for the triggered restart of Timer 3. The SSI must be supplied with the toggle
signal of Timer 2. The counter is driven by an internal or external clock source.
Figure 5-56. Pulse-width Modulation
TOG2
SIR
SO
0
1
0
1
SCO
T3R
Counter 3
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 2 3 4 5 6 7 8 9101112131415 0 1 2 3 4 5 6 7 8 9101112131415 0 1 2 3 4
CM31
CM32
T3O
77
4680C–4BMCU–01/05
Combination Mode 8: Manchester Demodulation/Pulse-width Demodulation
SSI mode 1:
Timer 3 mode 10:
8-bit shift register internal data input (SI) and the internal shift clock
(SCI) from the Timer 3
Manchester demodulation/pulse-width demodulation with Timer 3
For Manchester demodulation, the edge detection stage must be programmed to detect each
edge at the input. These edges are evaluated by the demodulator stage. The timer stage is used
to generate the shift clock for the SSI. A compare register 1 match event defines the correct
moment for shifting the state from the input T3I as the decoded bit into the shift register. After
that, the demodulator waits for the next edge to synchronize the timer by a reset for the next bit.
The compare register 2 can be used to detect a time error and handle it with an interrupt routine.
Before activating the demodulator mode the timer and the demodulator stage must be synchronized with the bit-stream. The Manchester code timing consists of parts with the half bit-length
and the complete bit-length. A synchronization routine must start the demodulator after an interval with the complete bit-length.
The counter can be driven by any internal clock source. The output T3O can be used by Timer 2
in this mode. The Manchester decoder can also be used for pulse-width demodulation. The input
must programmed to detect the positive edge. The demodulator and timer must be synchronized
with the leading edge of the pulse. After that a counter match with the compare register 1 shifts
the state at the input T3I into the shift register. The next positive edge at the input restarts the
timer.
Figure 5-57. Manchester Demodulation
Timer 3
mode
T3I
Synchronize
1
Manchester demodulation mode
0
1
1
1
0
0
1
1
0
T3EX
SI
CM31 = SCI
SR DATA
78
1
1
1
0
0
1
1
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
0
Bit 0
ATAM893-D
4680C–4BMCU–01/05
ATAM893-D
Combination Mode 9: Bi-phase Demodulation
SSI mode 1:
8-bit shift register internal data input (SI) and the internal shift clock
(SCI) from the Timer 3
Timer 3 mode 11:
Bi-phase demodulation with Timer 3
In the Bi-phase demodulation mode the timer works like in the Manchester demodulation mode.
The difference is that the bits are decoded with the toggle flip-flop. This flip-flop samples the
edge in the middle of the bit-frame and the compare register 1 match event shifts the toggle flipflop output into shift register. Before activating the demodulation the timer and the demodulation
stage must be synchronized with the bit-stream. The Bi-phase code timing consists of parts with
the half bit-length and the complete bit-length. The synchronization routine must start the
demodulator after an interval with the complete bit-length.
The counter can be driven by any internal clock source and the output T3O can be used by
Timer 2 in this mode.
Figure 5-58. Bi-phase Demodulation
Timer 3
mode
T3I
Synchronize
0
Bi-phase demodulation mode
0
0
0
1
0
1
1
1
0
1
1
0
1
0
1
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
T3EX
Q1 = SI
CM31 = SCI
Reset
Counter 3
SR-DATA
0
Bit 0
79
4680C–4BMCU–01/05
5.3.5.3
Combination Mode Timer 2 and Timer 3
Figure 5-59. Combination Timer 3 and Timer 2
I/O-bus
T3CS
T3M
T3I
T3EX
SCI
T3I
T3EX
SYSCL
T1OUT
POUT
CL3
CM31
CP3
T3CP
SI
Demodulator 3
RES
8-bit Counter 3
T3C
INT5
T3ST
TOG3
SO
Control
RES
Compare 3/1
Compare 3/2
T3CO1
T3CO2
Timer 3 - control
M2
TOG2
T3CM1
T3O
Modulator 3
T3CM2
I/O-bus
P4CR
T2I
SSI
T2M1
T2M2
DCGO
T2O
TOG3
SYSCL
T1OUT
SCL
CL2/1
CL2/2
4-bit Counter 2/1
RES
T2C
OVF1
DCG
POUT
Compare 2/1
RES
Timer 2 - control
OUTPUT
8-bit Counter 2/2
OVF2
TOG2
MOUT
M2
Compare 2/2
Bi-phase
Manchester
modulator
INT4
CM1
POUT
T2CO1
I/O-bus
T2CM
T2CO2
SO
Timer 2
modulator 2
output-stage
SSI
SSI
Control
(RE, FE, SCO, OMSK)
Combination Mode 10: Frequency Measurement or Event Counter with Time Gate
Timer 2 mode 1/2:
Timer 2 output mode 1/6:
12-bit compare counter/8-bit compare counter and 4-bit prescaler
Timer 2 compare match toggles (TOG2) to the Timer 3
Timer 3 mode 3:
Timer/Counter; integrated trigger restart and integrated
capture (with Timer 2 TOG2-signal)
The counter is driven by an external (T3I) clock source. The output signal (TOG2) of Timer 2
resets the counter. The counter value before reset is saved in the capture register. If singleaction mode is activated for one or both compare registers, the trigger signal restarts also the
single actions. This mode can be used for frequency measurements or as event counter with
time gate.
80
ATAM893-D
4680C–4BMCU–01/05
ATAM893-D
Figure 5-60. Frequency Measurement
T3R
T3I
Counter 3
0 0 1 2 3 4 5 6 7 8 9 10 11121314151617 0 1 2 3 4 5 6 7 8 9 10 1112131415161718 0 1 2 3 4 5
TOG2
Capture value = 0
T3CPRegister
Capture value = 17
Capt. value = 18
Figure 5-61. Event Counter with Time Gate
T3R
T3I
Counter 3
0 0 1 2 3 4 5 6 7 8 910
11
0 1
2
4
3
0 1 2
TOG2
Capture value = 0
T3CPRegister
Capture value = 4
Capture value = 11
Combination Mode 11: Burst Modulation 1
Timer 2 mode 1/2:
Timer 2 output mode 1/6:
12-bit compare counter/8-bit compare counter and 4-bit prescaler
Timer 2 compare match toggles the output flip-flop (M2) to the
Timer 3
Timer 3 mode 6:
Carrier frequency burst modulation controlled by Timer 2 output
(M2)
The Timer 3 counter is driven by an internal or external clock source. Its compare- and compare
mode registers must be programmed to generate the carrier frequency with the output toggle
flip-flop. The output toggle flip-flop (M2) of Timer 2 is used to enable and disable the Timer 3 output. The Timer 2 can be driven by the toggle output signal of Timer 3 (TOG3) or any other clock
source.
Figure 5-62. Burst Modulation 1
CL3
Counter 3
0 1 0 1 2 3 4 5 0 1 0 1 2 3 4 5 0 10 1 2 3 4 50 1 0 1
5 0 1 01
50 1 01
501 01
5 0 1 01
5 0 1 01
50 1 01
5 01 01
5 01 01
5 01 01
CM1
CM2
TOG3
M3
Counter 2/2
3
0
1
2
3
3
0
1
2
3
TOG2
M2
T3O
81
4680C–4BMCU–01/05
5.3.5.4
Combination Timer 2, Timer 3 and SSI
Figure 5-63. Combination Timer 2, Timer 3 and SSI
I/O-bus
T3CS
T3M
T3I
T3EX
SCI
Demodulator 3
T3I
CP3
T3CP
SI
CM31
RES
T3EX
SYSCL
T1OUT
POUT
CL3
8-bit Counter 3
T3C
INT5
T3ST
TOG3
SO
Control
RES
Compare 3/1
Compare 3/2
Timer 3 - control
TOG2
T3CO1
T3CO2
T3CM1
T3O
Modulator 3
M2
T3CM2
SSI
I/O-bus
P4CR
T2M1
T2M2
T2I
DCGO
T2O
TOG3
SYSCL
T1OUT
CL2/1
RES
SCL
CL2/2
4-bit Counter 2/1
OVF1
OUTPUT
8-bit Counter 2/2
POUT
Compare 2/1
T2C
DCG
RES
Timer 2 - control
OVF2
TOG2
MOUT
M2
Compare 2/2
Bi-phase
Manchester
modulator
INT4
CM1
POUT
T2CO1
T2CM
T2CO2
SO
Control
I/O-bus
Control
SIC1
SIC2
(RE, FE, SCO
OMSK)
SISC
TOG2
POUT
T1OUT
SYSCL
INT3
SCLI
SC
SSI-control
MCL_SC
Output
SO
SI
SCL
Shift_CL
MSB
8-bit shift register
STB
Transmit buffer
82
Timer 2
modulator 2
output-stage
LSB
MCL_SD
SI
SRB
I/O-bus
Receive buffer
ATAM893-D
4680C–4BMCU–01/05
ATAM893-D
Combination Mode 12: Burst Modulation 2
SSI mode 1:
8-bit shift register internal data output (SO) to the Timer 3
Timer 2 output mode 2:
Timer 2 output mode 1/6:
8-bit compare counter and 4-bit prescaler
Timer 2 compare match toggles (TOG2) to the SSI
Timer 3 mode 7:
Carrier frequency burst modulation controlled by the internal
output (SO) of SSI
The Timer 3 counter is driven by an internal or external clock source. Its compare- and compare
mode registers must be programmed to generate the carrier frequency with the output toggle
flip-flop (M3). The internal data output (SO) of the SSI is used to enable and disable the Timer 3
output. The SSI can be supplied with the toggle signal of Timer 2.
Figure 5-64. Burst Modulation 2
CL3
Counter 3
0 1 0 1 2 34 5 0 1 0 1 2 3 4 5 0 1 0 1 2 3 4 5 0 1 0 1
5 0 1 01
5 0 1 01
5 0 1 01
50 1 01
5 0 1 01
50101
501 01
5 01 01
5 0 1 01
CM31
CM32
TOG3
M3
Counter 2/2
3
0
1
2
3
3
0
1
2
3
TOG2
SO
T3O
Combination Mode 13: FSK Modulation
SSI mode 1:
8-bit shift register internal data output (SO) to the Timer 3
Timer 2 output mode 3:
Timer 2 output mode 1/6:
8-bit compare counter and 4-bit prescaler
Timer 2 4-bit compare match signal (POUT) to the SSI
Timer 3 mode 8:
FSK modulation with shift register data output (SO)
The two compare registers are used to generate two different time intervals. The SSI data output
selects which compare register is used for the output frequency generation. A '0' level at the SSI
data output enables the compare register 1 and a '1' level enables the compare register 2. The
compare- and compare mode registers must be programmed to generate the two frequencies
via the output toggle flip-flop. The SSI can be supplied with the toggle signal of Timer 2 or any
other clock source. The Timer 3 counter is driven by an internal or external clock source.
83
4680C–4BMCU–01/05
Figure 5-65. FSK Modulation
T3R
0 1 2 3 4 0 1 2 3 4 0 1 2 3 4 0 1 2 0 1 2 0 1 2 0 1 2 0 1 2 0 1 2 0 1 2 0 1 2 3 4 0 1
Counter 3
CM31
CM32
0
SO
1
0
T3O
6. Data EEPROM
The internal data EEPROM offers 2 pages of 512 bits each. Both pages are organized as
32 × 16 bit words. The programming voltage as well as the write cycle timing is generated on
chip.
If it is necessary to be compatible with the ROM parts, only the default page must be used with
the flash part. Also for compatibility reasons the access to the EEPROM is handled via the MCL
(serial interface) as in the corresponding ROM parts.
The page select is performed by either writing ''01h'' (page 1) or ''09h'' (page 0) to the EEPROM.
Figure 6-1.
Block Diagram EEPROM
Timing control
HV-generator
Page 1
VDD
VSS
Address
control
SCL
SDA
84
Page 0
2 × 32 × 16
Mode
control
I/O
control
--> write "01"h
EEPROM
--> write "09"h
16-bit read/write buffer
8-bit data register
ATAM893-D
4680C–4BMCU–01/05
ATAM893-D
6.1
Serial Interface
The EEPROM uses an MCL-like two-wire serial interface to the microcontroller for read and
write accesses to the data. It is considered to be a slave in all these applications. That means,
the controller has to be the master that initiates the data transfer and provides the clock for
transmit and receive operations.
The serial interface is controlled by the microcontroller which generates the serial clock and controls the access via the SCL-line and SDA-line. SCL is used to clock the data into and out of the
device. SDA is a bi-directional line that is used to transfer data into and out of the device. The
following protocol is used for the data transfers.
6.1.1
Serial Protocol
• Data states on the SDA-line changing only while SCL is low
• Changes on the SDA-line while SCL is high are interpreted as START or STOP condition
• A START condition is defined as a high to low transition on the SDA-line while the SCL-line is
high
• A STOP condition is defined as a low to high transition on the SDA-line while the SCL-line is
high
• Each data transfer must be initialized with a START condition and terminated with a STOP
condition. The START condition wakes the device from standby mode and the STOP
condition returns the device to standby mode.
• A receiving device generates an acknowledge (A) after the reception of each byte. This
requires an additional clock pulse, generated by the master. If the reception was successful
the receiving master or slave device pulls down the SDA-line during that clock cycle. If an
acknowledge is not detected (N) by the interface in transmit mode, it will terminate further
data transmissions and go into receive mode. A master device must finish its read operation
by a non-acknowledge and then send a stop condition to bring the device into a known state.
Figure 6-2.
MCL Protocol
SCL
SDA
Stand-by Start
condition
Data
valid
Data/
Data
change acknowledge
valid
Stop Stand-by
condition
• Before the START condition and after the STOP condition the device is in standby mode and
the SDA line is switched as input with pull-up resistor.
• The control byte that follows the START condition determines the following operation. It
consists of the 5-bit row address, 2 mode control bits and the READ/NWRITE bit that is used
to control the direction of the following transfer. A 0 defines a write access and a 1 a read
access.
85
4680C–4BMCU–01/05
6.1.2
Control Byte Format
EEPROM Address
6.2
Start
A4
A3
Start
Control byte
A2
Acne
Mode Control Bits
A1
A0
Data byte
C1
Acne
C0
Data byte
Read/
Write
R/NW
Acne
Acne
Stop
EEPROM
The EEPROM has a size of 2 × 512 bits and is organized as 32 x 16-bit matrix each. To read
and write data to and from the EEPROM the serial interface must be used. The interface supports one and two byte write accesses and one to n-byte read accesses to the EEPROM.
6.2.1
EEPROM - Operating Modes
The operating modes of the EEPROM are defined via the control byte. The control byte contains
the row address, the mode control bits and the read/not-write bit that is used to control the direction of the following transfer. A 0 defines a write access and a 1 a read access. The five address
bits select one of the 32 rows of the EEPROM memory to be accessed. For all accesses the
complete 16-bit word of the selected row is loaded into a buffer. The buffer must be read or overwritten via the serial interface. The two mode control bits C1 and C2 define in which order the
accesses to the buffer are performed: High byte – low byte or low byte – high byte. The
EEPROM also supports auto increment and auto decrement read operations.
After sending the start address with the corresponding mode, consecutive memory cells can be
read row by row without transmission of the row addresses.
Two special control bytes enable the complete initialization of EEPROM with 0 or with 1.
6.2.2
Write Operations
The EEPROM permits 8-bit and 16-bit write operations. A write access starts with the START
condition followed by a write control byte and one or two data bytes from the master. It is completed via the STOP condition from the master after the acknowledge cycle.
The programming cycle consists of an erase cycle (write “zeros”) and the write cycle (write
“ones”). Both cycles together take about 10 ms.
6.2.2.1
86
Acknowledge Polling
If the EEPROM is busy with an internal write cycle, all inputs are disabled and the EEPROM will
not acknowledge until the write cycle is finished. This can be used to detect the end of the write
cycle. The master must acknowledge polling by sending a start condition followed by the control
byte. If the device is still busy with the write cycle, it will not return an acknowledge and the master has to generate a stop condition or perform further acknowledge polling sequences. If the
cycle is complete, it returns an acknowledge and the master can proceed with the next read or
write cycle.
ATAM893-D
4680C–4BMCU–01/05
ATAM893-D
6.2.2.2
Write One Data Byte
Start
6.2.2.3
Data byte 1
A
Stop
Control byte
A
Data byte 1
A
Data byte 2
A
Stop
A
Stop
Write Control Byte Only
Start
6.2.2.5
A
Write Two Data Bytes
Start
6.2.2.4
Control byte
Control byte
Write Control Bytes
MSB
Write low byte first
A4
LSB
A3
A2
A1
A0
Row address
Byte order
LB(R)
C1
C0
R/NW
0
1
0
C1
C0
R/NW
1
0
0
HB(R)
MSB
Write high byte first
A4
LSB
A3
A2
A1
Row address
Byte order
HB(R)
A0
LB(R)
A →acknowledge; HB: high byte; LB: low byte; R: row address
6.2.3
Read Operations
The EEPROM allows byte-, word- and current address read operations. The read operations are
initiated in the same way as write operations. Every read access is initiated by sending the
START condition followed by the control byte which contains the address and the read mode.
When the device has received a read command, it returns an acknowledge, loads the addressed
word into the read/write buffer and sends the selected data byte to the master. The master has
to acknowledge the received byte if it wants to proceed with the read operation. If two bytes are
read out from the buffer the device increments respectively decrements the word address automatically and loads the buffer with the next word. The read mode bits determines if the low or
high byte is read first from the buffer and if the word address is incremented or decremented for
the next read access. If the memory address limit is reached, the data word address will “roll
over” and the sequential read will continue. The master can terminate the read operation after
every byte by not responding with an acknowledge (N) by issuing a stop condition.
87
4680C–4BMCU–01/05
6.2.3.1
Read One Data Byte
Start
6.2.3.2
Data byte 1
N
Stop
Control byte
A
Data byte 1
A
Data byte 2
N
Stop
Read n Data Bytes
Start
6.2.3.4
A
Read Two Data Bytes
Start
6.2.3.3
Control byte
Control byte
A
Data byte 1
A
Data byte 2
A ---
Data byte n
N Stop
Read Control Bytes
MSB
Read low byte first,
address increment
A4
LSB
A3
A2
A1
A0
Row address
Byte order
LB(R)
HB(R)
LB(R+1)
HB(R+1)
C1
C0
R/NW
0
1
1
---
LB(R+n)
MSB
Read high byte first,
address decrement
A4
LSB
A3
A2
A1
A0
Row address
Byte order
HB(R)
LB(R)
HB(R+n)
HB(R-1)
LB(R-1)
---
C1
C0
R/NW
1
0
1
HB(R-n)
LB(R-n)
A →acknowledge, N →no acknowledge; HB: high byte; LB: low byte, R: row address
6.2.3.5
Initializing the Serial Interface to the EEPROM
To prevent unexpected behavior of the EEPROM and its interface it is good practice to use an
initialization sequence after any reset of the circuit. This is performed by writing:
Start
“FFh”
A
N Stop
to the serial interface. If the EEPROM acknowledges this sequence it is in a defined state. It may
be necessary to perform this sequence twice.
88
ATAM893-D
4680C–4BMCU–01/05
ATAM893-D
7. Absolute Maximum Ratings
Voltages are given relative to VSS.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating
only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this
specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
All inputs and outputs are protected against high electrostatic voltages or electric fields. However, precautions to minimize the build-up of
electrostatic charges during handling are recommended. Reliability of operation is enhanced if unused inputs are connected to an
appropriate logic voltage level (e.g., VDD).
Parameters
Symbol
Value
Unit
Supply voltage
VDD
-0.3 to + 6.5
V
Input voltage (on any pin)
VIN
VSS -0.3 ≤VIN ≤VDD +0.3
V
Output short circuit duration
tshort
indefinite
s
Operating temperature range
Tamb
-40 to +125
°C
Storage temperature range
Tstg
-40 to +130
°C
Soldering temperature (t ≤10 s)
Tsld
260
°C
Symbol
Value
Unit
RthJA
140
K/W
8. Thermal Resistance
Parameter
Thermal resistance (SSO20)
9. DC Operating Characteristics
VSS = 0 V, Tamb = -40 to 125°C unless otherwise specified.
Parameters
Test Conditions
Symbol
Min.
VDD
VPOR
Typ.
Max.
Unit
6.5
V
0.4
1.0
mA
mA
mA
Power Supply
Operating voltage at VDD
Active current
CPU active
fSYSCL = 1 MHz
VDD = 1.8 V
VDD = 3.0 V
VDD = 6.5 V
IDD
Power down current
(CPU sleep,
RC oscillator active,
4-MHz quartz oscillator active)
fSYSCL = 1 MHz
VDD = 1.8 V
VDD = 3.0 V
VDD = 6.5 V
IPD
Sleep current (CPU sleep,
32-kHz quartz oscillator active
4-MHz quartz oscillator inactive)
VDD = 1.8 V
VDD = 3.0 V
VDD = 6.5 V
ISleep
0.4
0.6
0.8
4.3
7.8
µA
µA
µA
Sleep current (CPU sleep,
32-kHz quartz oscillator inactive
4-MHz quartz oscillator inactive)
VDD = 3.0 V
VDD = 6.5 V
ISleep
0.3
0.6
3.5
7.0
µA
µA
7
10
pF
Pin capacitance
Any pin to VSS
CL
Note:
The pin BP20/NTE has a static pull-up resistor during the reset-phase of the microcontroller
0.2
0.3
0.7
40
70
200
150
µA
µA
µA
89
4680C–4BMCU–01/05
9. DC Operating Characteristics (Continued)
VSS = 0 V, Tamb = -40 to 125°C unless otherwise specified.
Parameters
Test Conditions
Symbol
Min.
Typ.
Max.
Unit
VPOR
1.54
1.7
1.88
V
VPOR
1.83
2.0
2.20
V
Power-on Reset Threshold Voltage
POR threshold voltage
POR threshold voltage
BOT = 1
BOT = 0
POR hysteresis
50
VPOR
mV
Voltage Monitor Threshold Voltage
VM high threshold voltage
VDD > VM, VMS = 1
VMThh
VM high threshold voltage
VDD < VM, VMS = 0
VMThh
3.0
VM middle threshold voltage
VDD > VM, VMS = 1
VMThm
VM middle threshold voltage
VDD < VM, VMS = 0
VMThm
VM low threshold voltage
VDD > VM, VMS = 1
VMThl
VM low threshold voltage
VDD < VM, VMS = 0
VMThl
VMI
VDD = 3 V, VMS = 1
VVMI
VMI
VDD = 3 V, VMS = 0
VVMI
1.16
2.74
3.35
3.0
2.6
2.38
2.6
2.0
2.2
2.2
V
V
2.9
V
V
2.44
V
V
External Input Voltage
1.3
1.44
1.3
V
V
All Bi-directional Ports
Input voltage LOW
VDD = 1.8 to 6.5 V
VIL
VSS
0.2 ×
VDD
V
Input voltage HIGH
VDD = 1.8 to 6.5 V
VIH
0.8 × VDD
VDD
V
Input LOW current
(switched pull-up)
VDD = 2.0 V,
VDD = 3.0 V, VIL = VSS
VDD = 6.5 V
IIL
-3
-10
-80
-8
-20
-150
-14
-40
-240
µA
µA
µA
Input HIGH current
(switched pull-down)
VDD = 2.0 V,
VDD = 3.0 V, VIH = VDD
VDD = 6.5 V
IIH
2.5
10
60
8
20
100
14
40
160
µA
µA
µA
Input LOW current
(static pull-up)
VDD = 2.0 V
VDD = 3.0 V, VIL = VSS
VDD = 6.5 V
IIL
-30
-80
-300
-50
-160
-700
-90
-320
-1200
µA
µA
µA
Input LOW current
(static pull-down)
VDD = 2.0 V
VDD = 3.0 V, VIH = VDD
VDD = 6.5 V
IIH
20
80
300
50
160
600
100
320
1200
µA
µA
µA
Input leakage current
VIL = VSS
IIL
100
nA
Input leakage current
VIH = VDD
IIH
100
nA
Output LOW current
VOL = 0.2 × VDD
VDD = 2.0 V
VDD = 3.0 V,
VDD = 6.5 V
IOL
0.9
3
8
1.8
5
15
3.6
8
22
mA
mA
mA
VOH = 0.8 × VDD
VDD = 2.0 V
-0.8
IOH
Output HIGH current
VDD = 3.0 V,
-3
VDD = 6.5 V
-7
Note:
The pin BP20/NTE has a static pull-up resistor during the reset-phase of the microcontroller
-1.7
-5
-15
-3.4
-8
-24
mA
mA
mA
90
ATAM893-D
4680C–4BMCU–01/05
ATAM893-D
10. AC Characteristics
Supply voltage VDD = 1.8 to 6.5 V, VSS = 0 V, Tamb = 25°C unless otherwise specified.
Parameters
Test Conditions
Symbol
Min.
Typ.
Max.
Unit
VDD = 1.8 to 6.5 V
Tamb = -40 to 125° C
tSYSCL
500
2000
ns
VDD = 2.4 to 6.5 V
Tamb = -40 to 125° C
tSYSCL
250
2000
ns
Timer 2 input LOW time
Rise/fall time < 10 ns
tT2IL
100
5
MHz
ns
Timer 2 input HIGH time
Rise/fall time < 10 ns
tT2IH
100
ns
Timer 3 input LOW time
Rise/fall time < 10 ns
tT3IL
2 tSYSCL
ns
Timer 3 input HIGH time
Rise/fall time < 10 ns
tT3IH
2 tSYSCL
ns
Operation Cycle Time
System clock cycle
Timer 2 input Timing Pin T2I
Timer 2 input clock
fT2I
Timer 3 Input Timing Pin T3I
Timer 3 input clock
SYSCL/2
fT3I
MHz
Interrupt Request Input Timing
Interrupt request LOW time
Rise/fall time < 10 ns
tIRL
100
ns
Interrupt request HIGH time
Rise/fall time < 10 ns
tIRH
100
ns
Rise/fall time < 10 ns
fEXSCL
0.5
4
MHz
EXSCL at OSC1, ECM = DI
Rise/fall time < 10 ns
fEXSCL
0.02
4
MHz
Input HIGH time
Rise/fall time < 10 ns
tIH
0.1
External System Clock
EXSCL at OSC1, ECM = EN
µs
Reset Timing
Power-on reset time
VDD > VPOR
tPOR
1.5
fRcOut1
3.8
5
ms
RC Oscillator 1
Frequency
Stability
VDD = 2.0 to 6.5 V
Tamb = -40 to 125° C
∆f/f
MHz
±50
%
RC Oscillator 2 - External Resistor
Frequency
Rext = 180 kΩ
Stability
VDD = 2.0 to 6.5 V
Tamb = -40 to 125° C
Stabilization time
fRcOut2
4
MHz
∆f/f
+15
-20
%
tS
10
µs
4-MHz Crystal Oscillator (Operating Range VDD = 2.2 V to 6.5 V)
Frequency
fX
4
MHz
Start-up time
tSQ
5
ms
Stability
∆f/f
Integrated input/output capacitances
(configurable)
CIN/COUT programmable
CIN
COUT
-10
0, 2, 5, 7, 10 or 12
0, 2, 5, 7, 10 or 12
10
ppm
pF
pF
91
4680C–4BMCU–01/05
10. AC Characteristics (Continued)
Supply voltage VDD = 1.8 to 6.5 V, VSS = 0 V, Tamb = 25°C unless otherwise specified.
Parameters
Test Conditions
Symbol
Min.
Typ.
Max.
Unit
32-kHz Crystal Oscillator (Operating Range VDD = 2.0 V to 6.5 V)
fX
32.768
kHz
Start-up time
tSQ
0.5
s
Stability
∆f/f
Frequency
-10
10
ppm
CIN
COUT
0, 2, 5, 7, 10 or 12
0, 2, 5, 7, 10 or 12
pF
pF
Crystal frequency
fX
32.768
kHz
Serial resistance
RS
30
Static capacitance
C0
1.5
pF
Dynamic capacitance
C1
3
fF
Crystal frequency
fX
4.0
MHz
Serial resistance
RS
40
150
Ω
Static capacitance
C0
1.4
3
pF
Dynamic capacitance
C1
3
IWR
600
Integrated input/output capacitances
(configurable)
CIN/COUT programmable
External 32-kHz Crystal Parameters
50
kΩ
External 4-MHz Crystal Parameters
fF
EEPROM
Operating current during erase/write
cycle
Endurance, erase-/write cycles
Data erase/write cycle time
Tamb = 125°C
For 16-bit access
Data retention time
µA
ED
500000
1000000
Cycles
ED
10000
20000
Cycles
9
tDEW
Tamb = 85°C
1300
13
ms
tDR
100
Years
tDR
1
Years
Power-up to read operation
tPUR
0.2
ms
Power-up to write operation
tPUW
0.2
ms
Erase-/write cycles, Tamb = 0 to 40°C
Program EEPROM
nEW
100
1000
Cycles
Serial Interface
SCL clock frequency
100
fSC_MCL
500
kHz
11. Crystal Characteristics
Figure 11-1. Crystal Equivalent Circuit
L
C1
Equivalent
circuit
OSCIN
SCLIN
92
OSCOUT
SCLOUT
RS
C0
ATAM893-D
4680C–4BMCU–01/05
ATAM893-D
12. Emulation
The basic function of emulation is to test and evaluate the customer's program and hardware in
real time. This therefore enables the analysis of any timing, hardware or software problem. For
emulation purposes, all MARC4 controllers include a special emulation mode. In this mode, the
internal CPU core is inactive and the I/O buses are available via Port 0 and Port 1 to allow an
external access to the on-chip peripherals. The MARC4 emulator uses this mode to control the
peripherals of any MARC4 controller (target chip) and emulates the lost ports for the application.
The MARC4 emulator can stop and restart a program at specified points during execution, making it possible for the applications engineer to view the memory contents and those of various
registers during program execution. The designer also gains the ability to analyze the executed
instruction sequences and all the I/O activities.
Figure 12-1. MARC4 Emulation
Emulator target board
MARC4 emulator
MARC4
emulation-CPU
I/O bus
Trace
memory
Port 0
MARC4 target chip
CORE
I/O control
Port 1
Program
memory
CORE
(inactive)
Peripherals
Port 0
Control
logic
Port 1
Emulation control
SYSCL/
TCL,
TE, NRST
Application-specific hardware
Personal computer
93
4680C–4BMCU–01/05
13. Ordering Information
Extended Type Number(1)
Program Memory
Data-EEPROM
Package
ATAM893x-TKSYz
4 kB Flash
2x512 Bit
SSO20
ATAM893x-TKQYz
4 kB Flash
2x512 Bit
SSO20
Taped and reeled
SSO20
Taped and reeled +
Dry pack
ATAM893x-TKHYz
Note:
1. x
z
Y
4 kB Flash
2x512 Bit
Delivery
Tubes
= Hardware revision
= Operating temperature range
= D (-40°C to +125°C)
= Lead-free
14. Package Information
5.7
5.3
Package SSO20
Dimensions in mm
6.75
6.50
4.5
4.3
1.30
0.15
0.05
0.25
0.65
5.85
20
0.15
6.6
6.3
11
technical drawings
according to DIN
specifications
1
94
10
ATAM893-D
4680C–4BMCU–01/05
ATAM893-D
15. Revision History
Please note that the following page numbers referred to in this section refer to the specific revision
mentioned, not to this document.
Revision No.
4680C-4BMCU-01/05
History
•
•
•
•
•
•
•
•
•
•
•
Put datasheet in a new template.
Rename ATAM893-J in ATAM893-D
Lead-free Logo on page 1 added.
Section 4.2.7.1 “Interrupt Processing” on pages 9 changed.
Section 4.5.2.4 “4-MHz Oscillator” on pages 18 to 19 changed.
Figure 4-16 “4-MHz Crystal Oscillator” on page 18 changed.
Section 4.5.2.5 “32-kHz Oscillator” on page 19 changed.
Figure 4-17 “Ceramic Resonator” on page 19 changed.
Figure 4-18 “32-kHz Crystal Oscillator” on page 19 changed.
Section 5.3.3.17 “Timer 3 CaPture Register (T3CP) Byte Read” on page 60
changed.
Section 5.3.4.14 “Serial Interface Status and Control Register (SISC)” on
page 71 changed.
Section 5.3.4.15 “Serial Transmit Buffer (STB) - Byte Write” on page 72
changed.
Section 5.3.4.16 “Serial Transmit Buffer (SRB) - Byte Read” on page 72
changed.
Table “Ordering Information” on page 94 changed.
•
•
•
•
•
•
•
•
•
•
•
Put datasheet in a new template.
Rename ATAM893-D in ATAM893-J
Title on page 1 changed.
Description on page 1 changed.
Table 9 “Peripheral Addresses” on page 22 changed.
Section “Timer 2” on page 34 change.
Table 19 “Timer 2 Output Select Bits” on page 43 changed.
Section “Read Control Bytes” on page 83 changed.
Table “Absolute Maximum Ratings” on page 84 changed.
Section “Emulation” on page 88 added.
New Table “Ordering Information” on page 89 added.
•
•
•
4680B-4BMCU-05/04
95
4680C–4BMCU–01/05
16. Table of Contents
Features ..................................................................................................... 1
Description ................................................................................................ 1
1
Pin Configuration ..................................................................................... 2
2
Introduction .............................................................................................. 3
3
Differences Between ATAM893-D and ATARx90/x92 ........................... 3
3.1 Program Memory ......................................................................................................3
3.2 Configuration Memory ..............................................................................................3
3.3 Data Memory ............................................................................................................3
3.4 Reset Function .........................................................................................................3
3.5 RC-oscillator Frequency ...........................................................................................4
3.6 High Drive Outputs ...................................................................................................4
4
MARC4 Architecture ................................................................................ 4
4.1 General Description ..................................................................................................4
4.2 Components of MARC4 Core ...................................................................................5
4.3 Master Reset ..........................................................................................................11
4.4 Voltage Monitor ......................................................................................................13
4.5 Clock Generation ....................................................................................................15
4.6 Power-down Modes ................................................................................................21
5
Peripheral Modules ................................................................................ 22
5.1 Addressing Peripherals ..........................................................................................22
5.2 Bi-directional Ports .................................................................................................24
5.3 Universal Timer/Counter/ Communication Module (UTCM) ...................................31
6
Data EEPROM ......................................................................................... 84
6.1 Serial Interface .......................................................................................................85
6.2 EEPROM ................................................................................................................86
7
Absolute Maximum Ratings .................................................................. 89
8
Thermal Resistance ............................................................................... 89
9
DC Operating Characteristics ............................................................... 89
10 AC Characteristics ................................................................................. 91
11 Crystal Characteristics .......................................................................... 92
96
ATAM893-D
4680C–4BMCU–01/05
ATAM893-D
12 Emulation ................................................................................................ 93
13 Ordering Information ............................................................................. 94
14 Package Information ............................................................................. 94
15 Revision History ..................................................................................... 95
97
4680C–4BMCU–01/05
Atmel Corporation
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 487-2600
Regional Headquarters
Europe
Atmel Sarl
Route des Arsenaux 41
Case Postale 80
CH-1705 Fribourg
Switzerland
Tel: (41) 26-426-5555
Fax: (41) 26-426-5500
Asia
Room 1219
Chinachem Golden Plaza
77 Mody Road Tsimshatsui
East Kowloon
Hong Kong
Tel: (852) 2721-9778
Fax: (852) 2722-1369
Japan
9F, Tonetsu Shinkawa Bldg.
1-24-8 Shinkawa
Chuo-ku, Tokyo 104-0033
Japan
Tel: (81) 3-3523-3551
Fax: (81) 3-3523-7581
Atmel Operations
Memory
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 436-4314
RF/Automotive
Theresienstrasse 2
Postfach 3535
74025 Heilbronn, Germany
Tel: (49) 71-31-67-0
Fax: (49) 71-31-67-2340
Microcontrollers
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 436-4314
La Chantrerie
BP 70602
44306 Nantes Cedex 3, France
Tel: (33) 2-40-18-18-18
Fax: (33) 2-40-18-19-60
ASIC/ASSP/Smart Cards
1150 East Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906, USA
Tel: 1(719) 576-3300
Fax: 1(719) 540-1759
Biometrics/Imaging/Hi-Rel MPU/
High Speed Converters/RF Datacom
Avenue de Rochepleine
BP 123
38521 Saint-Egreve Cedex, France
Tel: (33) 4-76-58-30-00
Fax: (33) 4-76-58-34-80
Zone Industrielle
13106 Rousset Cedex, France
Tel: (33) 4-42-53-60-00
Fax: (33) 4-42-53-60-01
1150 East Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906, USA
Tel: 1(719) 576-3300
Fax: 1(719) 540-1759
Scottish Enterprise Technology Park
Maxwell Building
East Kilbride G75 0QR, Scotland
Tel: (44) 1355-803-000
Fax: (44) 1355-242-743
Literature Requests
www.atmel.com/literature
Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any
intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY
WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT
OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no
representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications
and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Atmel’s products are not
intended, authorized, or warranted for use as components in applications intended to support or sustain life.
© Atmel Corporation 2005. All rights reserved. Atmel ®, logo and combinations thereof, and others, are registered trademarks, and Everywhere You Are SM and others are the trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of
others.
Printed on recycled paper.
4680C–4BMCU–01/05