Features • High Performance, Low Power AVR® 8-Bit Microcontroller • Advanced RISC Architecture • • • • • • • • – 131 Powerful Instructions – Most Single Clock Cycle Execution – 32 x 8 General Purpose Working Registers – Fully Static Operation – Up to 20 MIPS Throughput at 20 MHz – On-chip 2-cycle Multiplier High Endurance Non-volatile Memory Segments – 4/8/16/32K Bytes of In-System Self-Programmable Flash program memory – 256/512/512/1K Bytes EEPROM – 512/1K/1K/2K Bytes Internal SRAM – Write/Erase Cycles: 10,000 Flash/100,000 EEPROM – Data retention: 20 years at 85°C/100 years at 25°C(1) – Optional Boot Code Section with Independent Lock Bits In-System Programming by On-chip Boot Program True Read-While-Write Operation – Programming Lock for Software Security Peripheral Features – Two 8-bit Timer/Counters with Separate Prescaler and Compare Mode – One 16-bit Timer/Counter with Separate Prescaler, Compare Mode, and Capture Mode – Real Time Counter with Separate Oscillator – Six PWM Channels – 8-channel 10-bit ADC in TQFP and QFN/MLF package Temperature Measurement – 6-channel 10-bit ADC in PDIP Package Temperature Measurement – Programmable Serial USART – Master/Slave SPI Serial Interface – Byte-oriented 2-wire Serial Interface (Philips I2C compatible) – Programmable Watchdog Timer with Separate On-chip Oscillator – On-chip Analog Comparator – Interrupt and Wake-up on Pin Change Special Microcontroller Features – Power-on Reset and Programmable Brown-out Detection – Internal Calibrated Oscillator – External and Internal Interrupt Sources – Six Sleep Modes: Idle, ADC Noise Reduction, Power-save, Power-down, Standby, and Extended Standby I/O and Packages – 23 Programmable I/O Lines – 28-pin PDIP, 32-lead TQFP, 28-pad QFN/MLF and 32-pad QFN/MLF Operating Voltage: – 1.8 - 5.5V Temperature Range: – -40°C to 85°C Speed Grade: – 0 - 4 [email protected] - 5.5V, 0 - 10 [email protected] - 5.5.V, 0 - 20 MHz @ 4.5 - 5.5V Power Consumption at 1 MHz, 1.8V, 25°C – Active Mode: 0.2 mA – Power-down Mode: 0.1 µA – Power-save Mode: 0.75 µA (Including 32 kHz RTC) 8-bit Microcontroller with 4/8/16/32K Bytes In-System Programmable Flash ATmega48A ATmega48PA ATmega88A ATmega88PA ATmega168A ATmega168PA ATmega328 ATmega328P Summary Rev. 8271BS–AVR–04/10 ATmega48A/48PA/88A/88PA/168A/168PA/328/328P 1. Pin Configurations Figure 1-1. Pinout ATmega48A/48PA/88A/88PA/168A/168PA/328/328P PDIP 32 31 30 29 28 27 26 25 PD2 (INT0/PCINT18) PD1 (TXD/PCINT17) PD0 (RXD/PCINT16) PC6 (RESET/PCINT14) PC5 (ADC5/SCL/PCINT13) PC4 (ADC4/SDA/PCINT12) PC3 (ADC3/PCINT11) PC2 (ADC2/PCINT10) TQFP Top View 24 23 22 21 20 19 18 17 1 2 3 4 5 6 7 8 PC1 (ADC1/PCINT9) PC0 (ADC0/PCINT8) ADC7 GND AREF ADC6 AVCC PB5 (SCK/PCINT5) (PCINT21/OC0B/T1) PD5 (PCINT22/OC0A/AIN0) PD6 (PCINT23/AIN1) PD7 (PCINT0/CLKO/ICP1) PB0 (PCINT1/OC1A) PB1 (PCINT2/SS/OC1B) PB2 (PCINT3/OC2A/MOSI) PB3 (PCINT4/MISO) PB4 9 10 11 12 13 14 15 16 PD2 (INT0/PCINT18) PD1 (TXD/PCINT17) PD0 (RXD/PCINT16) PC6 (RESET/PCINT14) PC5 (ADC5/SCL/PCINT13) PC4 (ADC4/SDA/PCINT12) PC3 (ADC3/PCINT11) PC2 (ADC2/PCINT10) PC2 (ADC2/PCINT10) PC1 (ADC1/PCINT9) PC0 (ADC0/PCINT8) GND AREF AVCC PB5 (SCK/PCINT5) (PCINT19/OC2B/INT1) PD3 (PCINT20/XCK/T0) PD4 GND VCC GND VCC (PCINT6/XTAL1/TOSC1) PB6 (PCINT7/XTAL2/TOSC2) PB7 24 23 22 21 20 19 18 17 1 2 3 4 5 6 7 8 PC1 (ADC1/PCINT9) PC0 (ADC0/PCINT8) ADC7 GND AREF ADC6 AVCC PB5 (SCK/PCINT5) 9 10 11 12 13 14 15 16 8 9 10 11 12 13 14 (PCINT22/OC0A/AIN0) PD6 (PCINT23/AIN1) PD7 (PCINT0/CLKO/ICP1) PB0 (PCINT1/OC1A) PB1 (PCINT2/SS/OC1B) PB2 (PCINT3/OC2A/MOSI) PB3 (PCINT4/MISO) PB4 NOTE: Bottom pad should be soldered to ground. PC5 (ADC5/SCL/PCINT13) PC4 (ADC4/SDA/PCINT12) PC3 (ADC3/PCINT11) PC2 (ADC2/PCINT10) PC1 (ADC1/PCINT9) PC0 (ADC0/PCINT8) GND AREF AVCC PB5 (SCK/PCINT5) PB4 (MISO/PCINT4) PB3 (MOSI/OC2A/PCINT3) PB2 (SS/OC1B/PCINT2) PB1 (OC1A/PCINT1) 32 31 30 29 28 27 26 25 PD2 (INT0/PCINT18) PD1 (TXD/PCINT17) PD0 (RXD/PCINT16) PC6 (RESET/PCINT14) PC5 (ADC5/SCL/PCINT13) PC4 (ADC4/SDA/PCINT12) PC3 (ADC3/PCINT11) 28 27 26 25 24 23 22 21 20 19 18 17 16 15 1 2 3 4 5 6 7 28 27 26 25 24 23 22 21 20 19 18 17 16 15 32 MLF Top View 28 MLF Top View (PCINT19/OC2B/INT1) PD3 (PCINT20/XCK/T0) PD4 VCC GND (PCINT6/XTAL1/TOSC1) PB6 (PCINT7/XTAL2/TOSC2) PB7 (PCINT21/OC0B/T1) PD5 1 2 3 4 5 6 7 8 9 10 11 12 13 14 NOTE: Bottom pad should be soldered to ground. (PCINT21/OC0B/T1) PD5 (PCINT22/OC0A/AIN0) PD6 (PCINT23/AIN1) PD7 (PCINT0/CLKO/ICP1) PB0 (PCINT1/OC1A) PB1 (PCINT2/SS/OC1B) PB2 (PCINT3/OC2A/MOSI) PB3 (PCINT4/MISO) PB4 (PCINT19/OC2B/INT1) PD3 (PCINT20/XCK/T0) PD4 GND VCC GND VCC (PCINT6/XTAL1/TOSC1) PB6 (PCINT7/XTAL2/TOSC2) PB7 (PCINT14/RESET) PC6 (PCINT16/RXD) PD0 (PCINT17/TXD) PD1 (PCINT18/INT0) PD2 (PCINT19/OC2B/INT1) PD3 (PCINT20/XCK/T0) PD4 VCC GND (PCINT6/XTAL1/TOSC1) PB6 (PCINT7/XTAL2/TOSC2) PB7 (PCINT21/OC0B/T1) PD5 (PCINT22/OC0A/AIN0) PD6 (PCINT23/AIN1) PD7 (PCINT0/CLKO/ICP1) PB0 2 8271BS–AVR–04/10 ATmega48A/48PA/88A/88PA/168A/168PA/328/328P 1.1 1.1.1 Pin Descriptions VCC Digital supply voltage. 1.1.2 GND Ground. 1.1.3 Port B (PB7:0) XTAL1/XTAL2/TOSC1/TOSC2 Port B is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The Port B output buffers have symmetrical drive characteristics with both high sink and source capability. As inputs, Port B pins that are externally pulled low will source current if the pull-up resistors are activated. The Port B pins are tri-stated when a reset condition becomes active, even if the clock is not running. Depending on the clock selection fuse settings, PB6 can be used as input to the inverting Oscillator amplifier and input to the internal clock operating circuit. Depending on the clock selection fuse settings, PB7 can be used as output from the inverting Oscillator amplifier. If the Internal Calibrated RC Oscillator is used as chip clock source, PB7...6 is used as TOSC2...1 input for the Asynchronous Timer/Counter2 if the AS2 bit in ASSR is set. The various special features of Port B are elaborated in and ”System Clock and Clock Options” on page 26. 1.1.4 Port C (PC5:0) Port C is a 7-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The PC5...0 output buffers have symmetrical drive characteristics with both high sink and source capability. As inputs, Port C pins that are externally pulled low will source current if the pull-up resistors are activated. The Port C pins are tri-stated when a reset condition becomes active, even if the clock is not running. 1.1.5 PC6/RESET If the RSTDISBL Fuse is programmed, PC6 is used as an I/O pin. Note that the electrical characteristics of PC6 differ from those of the other pins of Port C. If the RSTDISBL Fuse is unprogrammed, PC6 is used as a Reset input. A low level on this pin for longer than the minimum pulse length will generate a Reset, even if the clock is not running. The minimum pulse length is given in Table 28-12 on page 323. Shorter pulses are not guaranteed to generate a Reset. The various special features of Port C are elaborated in ”Alternate Functions of Port C” on page 86. 1.1.6 Port D (PD7:0) Port D is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The Port D output buffers have symmetrical drive characteristics with both high sink and source capability. As inputs, Port D pins that are externally pulled low will source current if the pull-up resistors are activated. The Port D pins are tri-stated when a reset condition becomes active, even if the clock is not running. 3 8271BS–AVR–04/10 ATmega48A/48PA/88A/88PA/168A/168PA/328/328P The various special features of Port D are elaborated in ”Alternate Functions of Port D” on page 89. 1.1.7 AVCC AVCC is the supply voltage pin for the A/D Converter, PC3:0, and ADC7:6. It should be externally connected to VCC, even if the ADC is not used. If the ADC is used, it should be connected to VCC through a low-pass filter. Note that PC6...4 use digital supply voltage, VCC. 1.1.8 AREF AREF is the analog reference pin for the A/D Converter. 1.1.9 ADC7:6 (TQFP and QFN/MLF Package Only) In the TQFP and QFN/MLF package, ADC7:6 serve as analog inputs to the A/D converter. These pins are powered from the analog supply and serve as 10-bit ADC channels. 4 8271BS–AVR–04/10 ATmega48A/48PA/88A/88PA/168A/168PA/328/328P 2. Overview The ATmega48A/48PA/88A/88PA/168A/168PA/328/328P is a low-power CMOS 8-bit microcontroller based on the AVR enhanced RISC architecture. By executing powerful instructions in a single clock cycle, the ATmega48A/48PA/88A/88PA/168A/168PA/328/328P achieves throughputs approaching 1 MIPS per MHz allowing the system designer to optimize power consumption versus processing speed. Block Diagram Block Diagram GND Figure 2-1. VCC 2.1 Watchdog Timer Watchdog Oscillator Oscillator Circuits / Clock Generation Power Supervision POR / BOD & RESET debugWIRE Flash SRAM PROGRAM LOGIC CPU EEPROM AVCC AREF DATABUS GND 8bit T/C 0 16bit T/C 1 A/D Conv. 8bit T/C 2 Analog Comp. Internal Bandgap USART 0 SPI TWI PORT D (8) PORT B (8) PORT C (7) 2 6 RESET XTAL[1..2] PD[0..7] PB[0..7] PC[0..6] ADC[6..7] The AVR core combines a rich instruction set with 32 general purpose working registers. All the 32 registers are directly connected to the Arithmetic Logic Unit (ALU), allowing two independent 5 8271BS–AVR–04/10 ATmega48A/48PA/88A/88PA/168A/168PA/328/328P registers to be accessed in one single instruction executed in one clock cycle. The resulting architecture is more code efficient while achieving throughputs up to ten times faster than conventional CISC microcontrollers. The ATmega48A/48PA/88A/88PA/168A/168PA/328/328P provides the following features: 4K/8K bytes of In-System Programmable Flash with Read-While-Write capabilities, 256/512/512/1K bytes EEPROM, 512/1K/1K/2K bytes SRAM, 23 general purpose I/O lines, 32 general purpose working registers, three flexible Timer/Counters with compare modes, internal and external interrupts, a serial programmable USART, a byte-oriented 2-wire Serial Interface, an SPI serial port, a 6-channel 10-bit ADC (8 channels in TQFP and QFN/MLF packages), a programmable Watchdog Timer with internal Oscillator, and five software selectable power saving modes. The Idle mode stops the CPU while allowing the SRAM, Timer/Counters, USART, 2-wire Serial Interface, SPI port, and interrupt system to continue functioning. The Power-down mode saves the register contents but freezes the Oscillator, disabling all other chip functions until the next interrupt or hardware reset. In Power-save mode, the asynchronous timer continues to run, allowing the user to maintain a timer base while the rest of the device is sleeping. The ADC Noise Reduction mode stops the CPU and all I/O modules except asynchronous timer and ADC, to minimize switching noise during ADC conversions. In Standby mode, the crystal/resonator Oscillator is running while the rest of the device is sleeping. This allows very fast start-up combined with low power consumption. The device is manufactured using Atmel’s high density non-volatile memory technology. The On-chip ISP Flash allows the program memory to be reprogrammed In-System through an SPI serial interface, by a conventional non-volatile memory programmer, or by an On-chip Boot program running on the AVR core. The Boot program can use any interface to download the application program in the Application Flash memory. Software in the Boot Flash section will continue to run while the Application Flash section is updated, providing true Read-While-Write operation. By combining an 8-bit RISC CPU with In-System Self-Programmable Flash on a monolithic chip, the Atmel ATmega48A/48PA/88A/88PA/168A/168PA/328/328P is a powerful microcontroller that provides a highly flexible and cost effective solution to many embedded control applications. The ATmega48A/48PA/88A/88PA/168A/168PA/328/328P AVR is supported with a full suite of program and system development tools including: C Compilers, Macro Assemblers, Program Debugger/Simulators, In-Circuit Emulators, and Evaluation kits. 2.2 Comparison Between Processors The ATmega48A/48PA/88A/88PA/168A/168PA/328/328P differ only in memory sizes, boot loader support, and interrupt vector sizes. Table 2-1 summarizes the different memory and interrupt vector sizes for the devices. Table 2-1. Memory Size Summary Device Flash EEPROM RAM Interrupt Vector Size ATmega48A 4K Bytes 256 Bytes 512 Bytes 1 instruction word/vector ATmega48PA 4K Bytes 256 Bytes 512 Bytes 1 instruction word/vector ATmega88A 8K Bytes 512 Bytes 1K Bytes 1 instruction word/vector ATmega88PA 8K Bytes 512 Bytes 1K Bytes 1 instruction word/vector ATmega168A 16K Bytes 512 Bytes 1K Bytes 2 instruction words/vector 6 8271BS–AVR–04/10 ATmega48A/48PA/88A/88PA/168A/168PA/328/328P Table 2-1. Memory Size Summary Device Flash EEPROM RAM Interrupt Vector Size ATmega168PA 16K Bytes 512 Bytes 1K Bytes 2 instruction words/vector ATmega328 32K Bytes 1K Bytes 2K Bytes 2 instruction words/vector ATmega328P 32K Bytes 1K Bytes 2K Bytes 2 instruction words/vector ATmega48A/48PA/88A/88PA/168A/168PA/328/328P support a real Read-While-Write Self-Programming mechanism. There is a separate Boot Loader Section, and the SPM instruction can only execute from there. In ATmega 48A/48PA there is no Read-While-Write support and no separate Boot Loader Section. The SPM instruction can execute from the entire Flash. 3. Resources A comprehensive set of development tools, application notes and datasheets are available for download on http://www.atmel.com/avr. Note: 1. 7 8271BS–AVR–04/10 ATmega48A/48PA/88A/88PA/168A/168PA/328/328P 4. Register Summary Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (0xFF) Reserved – – – – – – – – (0xFE) Reserved – – – – – – – – (0xFD) Reserved – – – – – – – – (0xFC) Reserved – – – – – – – – (0xFB) Reserved – – – – – – – – (0xFA) Reserved – – – – – – – – (0xF9) Reserved – – – – – – – – (0xF8) Reserved – – – – – – – – (0xF7) Reserved – – – – – – – – (0xF6) Reserved – – – – – – – – (0xF5) Reserved – – – – – – – – (0xF4) Reserved – – – – – – – – (0xF3) Reserved – – – – – – – – (0xF2) Reserved – – – – – – – – (0xF1) Reserved – – – – – – – – (0xF0) Reserved – – – – – – – – (0xEF) Reserved – – – – – – – – (0xEE) Reserved – – – – – – – – (0xED) Reserved – – – – – – – – (0xEC) Reserved – – – – – – – – (0xEB) Reserved – – – – – – – – (0xEA) Reserved – – – – – – – – (0xE9) Reserved – – – – – – – – (0xE8) Reserved – – – – – – – – (0xE7) Reserved – – – – – – – – (0xE6) Reserved – – – – – – – – (0xE5) Reserved – – – – – – – – (0xE4) Reserved – – – – – – – – (0xE3) Reserved – – – – – – – – (0xE2) Reserved – – – – – – – – (0xE1) Reserved – – – – – – – – (0xE0) Reserved – – – – – – – – (0xDF) Reserved – – – – – – – – (0xDE) Reserved – – – – – – – – (0xDD) Reserved – – – – – – – – (0xDC) Reserved – – – – – – – – (0xDB) Reserved – – – – – – – – (0xDA) Reserved – – – – – – – – (0xD9) Reserved – – – – – – – – (0xD8) Reserved – – – – – – – – (0xD7) Reserved – – – – – – – – (0xD6) Reserved – – – – – – – – (0xD5) Reserved – – – – – – – – (0xD4) Reserved – – – – – – – – (0xD3) Reserved – – – – – – – – (0xD2) Reserved – – – – – – – – (0xD1) Reserved – – – – – – – – (0xD0) Reserved – – – – – – – – (0xCF) Reserved – – – – – – – – (0xCE) Reserved – – – – – – – – (0xCD) Reserved – – – – – – – – (0xCC) Reserved – – – – – – – – (0xCB) Reserved – – – – – – – – (0xCA) Reserved – – – – – – – – (0xC9) Reserved – – – – – – – – (0xC8) Reserved – – – – – – – – (0xC7) Reserved – – – – – – – – (0xC6) UDR0 (0xC5) UBRR0H USART I/O Data Register Page 196 USART Baud Rate Register High 200 (0xC4) UBRR0L (0xC3) Reserved – – – USART Baud Rate Register Low – – – – – 200 (0xC2) UCSR0C UMSEL01 UMSEL00 UPM01 UPM00 USBS0 UCSZ01 /UDORD0 UCSZ00 / UCPHA0 UCPOL0 198/213 8 8271BS–AVR–04/10 ATmega48A/48PA/88A/88PA/168A/168PA/328/328P Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (0xC1) UCSR0B RXCIE0 TXCIE0 UDRIE0 RXEN0 TXEN0 UCSZ02 RXB80 TXB80 Page 197 (0xC0) UCSR0A RXC0 TXC0 UDRE0 FE0 DOR0 UPE0 U2X0 MPCM0 196 (0xBF) Reserved – – – – – – – – (0xBE) Reserved – – – – – – – – (0xBD) TWAMR TWAM6 TWAM5 TWAM4 TWAM3 TWAM2 TWAM1 TWAM0 – 245 (0xBC) TWCR TWINT TWEA TWSTA TWSTO TWWC TWEN – TWIE 242 (0xBB) TWDR (0xBA) TWAR TWA6 TWA5 TWA4 TWS7 TWS6 TWS5 2-wire Serial Interface Data Register (0xB9) TWSR (0xB8) TWBR (0xB7) Reserved – (0xB6) ASSR – (0xB5) Reserved – 244 TWA3 TWA2 TWA1 TWA0 TWGCE 245 TWS4 TWS3 – TWPS1 TWPS0 244 2-wire Serial Interface Bit Rate Register 242 – – – – – – EXCLK AS2 TCN2UB OCR2AUB OCR2BUB TCR2AUB TCR2BUB – – – – – – – 165 (0xB4) OCR2B Timer/Counter2 Output Compare Register B 163 (0xB3) OCR2A Timer/Counter2 Output Compare Register A 163 (0xB2) TCNT2 (0xB1) TCCR2B FOC2A FOC2B – Timer/Counter2 (8-bit) – WGM22 CS22 CS21 CS20 163 162 (0xB0) TCCR2A COM2A1 COM2A0 COM2B1 COM2B0 – – WGM21 WGM20 159 (0xAF) Reserved – – – – – – – – (0xAE) Reserved – – – – – – – – (0xAD) Reserved – – – – – – – – (0xAC) Reserved – – – – – – – – (0xAB) Reserved – – – – – – – – (0xAA) Reserved – – – – – – – – (0xA9) Reserved – – – – – – – – (0xA8) Reserved – – – – – – – – (0xA7) Reserved – – – – – – – – (0xA6) Reserved – – – – – – – – (0xA5) Reserved – – – – – – – – (0xA4) Reserved – – – – – – – – (0xA3) Reserved – – – – – – – – (0xA2) Reserved – – – – – – – – (0xA1) Reserved – – – – – – – – (0xA0) Reserved – – – – – – – – (0x9F) Reserved – – – – – – – – (0x9E) Reserved – – – – – – – – (0x9D) Reserved – – – – – – – – (0x9C) Reserved – – – – – – – – (0x9B) Reserved – – – – – – – – (0x9A) Reserved – – – – – – – – (0x99) Reserved – – – – – – – – (0x98) Reserved – – – – – – – – (0x97) Reserved – – – – – – – – (0x96) Reserved – – – – – – – – (0x95) Reserved – – – – – – – – (0x94) Reserved – – – – – – – – (0x93) Reserved – – – – – – – – (0x92) Reserved – – – – – – – – (0x91) Reserved – – – – – – – – (0x90) Reserved – – – – – – – – (0x8F) Reserved – – – – – – – – (0x8E) Reserved – – – – – – – – (0x8D) Reserved – – – – – – – – (0x8C) Reserved – – – – – – – – (0x8B) OCR1BH Timer/Counter1 - Output Compare Register B High Byte 139 (0x8A) OCR1BL Timer/Counter1 - Output Compare Register B Low Byte 139 (0x89) OCR1AH Timer/Counter1 - Output Compare Register A High Byte 139 (0x88) OCR1AL Timer/Counter1 - Output Compare Register A Low Byte 139 (0x87) ICR1H Timer/Counter1 - Input Capture Register High Byte 139 (0x86) ICR1L Timer/Counter1 - Input Capture Register Low Byte 139 (0x85) TCNT1H Timer/Counter1 - Counter Register High Byte 139 (0x84) TCNT1L Timer/Counter1 - Counter Register Low Byte 139 (0x83) Reserved – – – – – – – (0x82) TCCR1C FOC1A FOC1B – – – – – – (0x81) TCCR1B ICNC1 ICES1 – WGM13 WGM12 CS12 CS11 CS10 137 (0x80) TCCR1A COM1A1 COM1A0 COM1B1 COM1B0 – – WGM11 WGM10 135 – 138 9 8271BS–AVR–04/10 ATmega48A/48PA/88A/88PA/168A/168PA/328/328P Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (0x7F) DIDR1 – – – – – – AIN1D AIN0D 250 (0x7E) DIDR0 – – ADC5D ADC4D ADC3D ADC2D ADC1D ADC0D 267 (0x7D) Reserved – – – – – – – – (0x7C) ADMUX REFS1 REFS0 ADLAR – MUX3 MUX2 MUX1 MUX0 263 (0x7B) ADCSRB – ACME – – – ADTS2 ADTS1 ADTS0 266 (0x7A) ADCSRA ADEN ADSC ADATE ADIF ADIE ADPS2 ADPS1 ADPS0 (0x79) ADCH ADC Data Register High byte Page 264 266 (0x78) ADCL (0x77) Reserved – – – – – – – – (0x76) Reserved – – – – – – – – (0x75) Reserved – – – – – – – – (0x74) Reserved – – – – – – – – (0x73) Reserved – – – – – – – – (0x72) Reserved – – – – – – – – (0x71) Reserved – – – – – – – – (0x70) TIMSK2 – – – – – OCIE2B OCIE2A TOIE2 164 (0x6F) TIMSK1 – – ICIE1 – – OCIE1B OCIE1A TOIE1 140 (0x6E) TIMSK0 – – – – – OCIE0B OCIE0A TOIE0 112 (0x6D) PCMSK2 PCINT23 PCINT22 PCINT21 PCINT20 PCINT19 PCINT18 PCINT17 PCINT16 75 (0x6C) PCMSK1 – PCINT14 PCINT13 PCINT12 PCINT11 PCINT10 PCINT9 PCINT8 75 (0x6B) PCMSK0 PCINT7 PCINT6 PCINT5 PCINT4 PCINT3 PCINT2 PCINT1 PCINT0 75 (0x6A) Reserved – – – – – – – – (0x69) EICRA – – – – ISC11 ISC10 ISC01 ISC00 (0x68) PCICR – – – – – PCIE2 PCIE1 PCIE0 (0x67) Reserved – – – – – – – – (0x66) OSCCAL (0x65) Reserved – – – – – – – – (0x64) PRR PRTWI PRTIM2 PRTIM0 – PRTIM1 PRSPI PRUSART0 PRADC (0x63) Reserved – – – – – – – – (0x62) Reserved – – – – – – – – (0x61) CLKPR CLKPCE – – – CLKPS3 CLKPS2 CLKPS1 CLKPS0 37 (0x60) WDTCSR WDIF WDIE WDP3 WDCE WDE WDP2 WDP1 WDP0 55 0x3F (0x5F) SREG I T H S V N Z C 9 0x3E (0x5E) SPH – – – – – (SP10) 5. SP9 SP8 12 0x3D (0x5D) SPL SP7 SP6 SP5 SP4 SP3 SP2 SP1 SP0 12 0x3C (0x5C) Reserved – – – – – – – – 0x3B (0x5B) Reserved – – – – – – – – 0x3A (0x5A) Reserved – – – – – – – – 0x39 (0x59) Reserved – – – – – – – – 0x38 (0x58) Reserved – – – – – – – – 0x37 (0x57) SPMCSR SPMIE (RWWSB)5. – (RWWSRE)5. BLBSET PGWRT PGERS SELFPRGEN 0x36 (0x56) Reserved – – – – – – – – 0x35 (0x55) MCUCR – BODS(6) BODSE(6) PUD – – IVSEL IVCE 0x34 (0x54) MCUSR – – – – WDRF BORF EXTRF PORF 55 0x33 (0x53) SMCR – – – – SM2 SM1 SM0 SE 40 0x32 (0x52) Reserved – – – – – – – – 0x31 (0x51) Reserved – – – – – – – – 0x30 (0x50) ACSR ACD ACBG ACO ACI ACIE ACIC ACIS1 ACIS0 0x2F (0x4F) Reserved – – – – – – – – 0x2E (0x4E) SPDR 0x2D (0x4D) SPSR SPIF WCOL – – – – – SPI2X 175 0x2C (0x4C) SPCR SPIE SPE DORD MSTR CPOL CPHA SPR1 SPR0 174 0x2B (0x4B) GPIOR2 General Purpose I/O Register 2 0x2A (0x4A) GPIOR1 General Purpose I/O Register 1 0x29 (0x49) Reserved 0x28 (0x48) OCR0B Timer/Counter0 Output Compare Register B 0x27 (0x47) OCR0A Timer/Counter0 Output Compare Register A 0x26 (0x46) TCNT0 0x25 (0x45) TCCR0B FOC0A FOC0B – – WGM02 CS02 CS01 CS00 0x24 (0x44) TCCR0A COM0A1 COM0A0 COM0B1 COM0B0 – – WGM01 WGM00 0x23 (0x43) GTCCR TSM – – – – – PSRASY PSRSYNC 0x22 (0x42) EEARH (EEPROM Address Register High Byte) 5. 0x21 (0x41) EEARL EEPROM Address Register Low Byte 21 0x20 (0x40) EEDR EEPROM Data Register 21 0x1F (0x3F) EECR 0x1E (0x3E) GPIOR0 ADC Data Register Low byte 266 Oscillator Calibration Register 37 SPI Data Register – – – – 72 42 294 45/69/93 248 176 25 25 – – – – Timer/Counter0 (8-bit) – – EEPM1 EEPM0 EERIE General Purpose I/O Register 0 144/166 21 EEMPE EEPE EERE 21 25 10 8271BS–AVR–04/10 ATmega48A/48PA/88A/88PA/168A/168PA/328/328P Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0x1D (0x3D) EIMSK – – – – – – INT1 INT0 Page 73 0x1C (0x3C) EIFR – – – – – – INTF1 INTF0 73 0x1B (0x3B) PCIFR – – – – – PCIF2 PCIF1 PCIF0 0x1A (0x3A) Reserved – – – – – – – – 0x19 (0x39) Reserved – – – – – – – – 0x18 (0x38) Reserved – – – – – – – – 0x17 (0x37) TIFR2 – – – – – OCF2B OCF2A TOV2 164 0x16 (0x36) TIFR1 – – ICF1 – – OCF1B OCF1A TOV1 140 0x15 (0x35) TIFR0 – – – – – OCF0B OCF0A TOV0 0x14 (0x34) Reserved – – – – – – – – 0x13 (0x33) Reserved – – – – – – – – 0x12 (0x32) Reserved – – – – – – – – 0x11 (0x31) Reserved – – – – – – – – 0x10 (0x30) Reserved – – – – – – – – 0x0F (0x2F) Reserved – – – – – – – – 0x0E (0x2E) Reserved – – – – – – – – 0x0D (0x2D) Reserved – – – – – – – – 0x0C (0x2C) Reserved – – – – – – – – 0x0B (0x2B) PORTD PORTD7 PORTD6 PORTD5 PORTD4 PORTD3 PORTD2 PORTD1 PORTD0 94 0x0A (0x2A) DDRD DDD7 DDD6 DDD5 DDD4 DDD3 DDD2 DDD1 DDD0 94 0x09 (0x29) PIND PIND7 PIND6 PIND5 PIND4 PIND3 PIND2 PIND1 PIND0 94 0x08 (0x28) PORTC – PORTC6 PORTC5 PORTC4 PORTC3 PORTC2 PORTC1 PORTC0 93 0x07 (0x27) DDRC – DDC6 DDC5 DDC4 DDC3 DDC2 DDC1 DDC0 93 0x06 (0x26) PINC – PINC6 PINC5 PINC4 PINC3 PINC2 PINC1 PINC0 93 0x05 (0x25) PORTB PORTB7 PORTB6 PORTB5 PORTB4 PORTB3 PORTB2 PORTB1 PORTB0 93 0x04 (0x24) DDRB DDB7 DDB6 DDB5 DDB4 DDB3 DDB2 DDB1 DDB0 93 0x03 (0x23) PINB PINB7 PINB6 PINB5 PINB4 PINB3 PINB2 PINB1 PINB0 93 0x02 (0x22) Reserved – – – – – – – – 0x01 (0x21) Reserved – – – – – – – – 0x0 (0x20) Reserved – – – – – – – – Note: 1. For compatibility with future devices, reserved bits should be written to zero if accessed. Reserved I/O memory addresses should never be written. 2. I/O Registers within the address range 0x00 - 0x1F are directly bit-accessible using the SBI and CBI instructions. In these registers, the value of single bits can be checked by using the SBIS and SBIC instructions. 3. Some of the Status Flags are cleared by writing a logical one to them. Note that, unlike most other AVRs, the CBI and SBI instructions will only operate on the specified bit, and can therefore be used on registers containing such Status Flags. The CBI and SBI instructions work with registers 0x00 to 0x1F only. 4. When using the I/O specific commands IN and OUT, the I/O addresses 0x00 - 0x3F must be used. When addressing I/O Registers as data space using LD and ST instructions, 0x20 must be added to these addresses. The ATmega48A/48PA/88A/88PA/168A/168PA/328/328P is a complex microcontroller with more peripheral units than can be supported within the 64 location reserved in Opcode for the IN and OUT instructions. For the Extended I/O space from 0x60 - 0xFF in SRAM, only the ST/STS/STD and LD/LDS/LDD instructions can be used. 5. Only valid for ATmega88A/88PA/168A/168PA/328/328P. 6. BODS and BODSE only available for picoPower devices ATmega48PA/88PA/168PA/328P 11 8271BS–AVR–04/10 ATmega48A/48PA/88A/88PA/168A/168PA/328/328P 5. Instruction Set Summary Mnemonics Operands Description Operation Flags #Clocks ARITHMETIC AND LOGIC INSTRUCTIONS ADD Rd, Rr Add two Registers Rd ← Rd + Rr Z,C,N,V,H ADC Rd, Rr Add with Carry two Registers Rd ← Rd + Rr + C Z,C,N,V,H 1 ADIW Rdl,K Add Immediate to Word Rdh:Rdl ← Rdh:Rdl + K Z,C,N,V,S 2 SUB Rd, Rr Subtract two Registers Rd ← Rd - Rr Z,C,N,V,H 1 SUBI Rd, K Subtract Constant from Register Rd ← Rd - K Z,C,N,V,H 1 SBC Rd, Rr Subtract with Carry two Registers Rd ← Rd - Rr - C Z,C,N,V,H 1 SBCI Rd, K Subtract with Carry Constant from Reg. Rd ← Rd - K - C Z,C,N,V,H 1 SBIW Rdl,K Subtract Immediate from Word Rdh:Rdl ← Rdh:Rdl - K Z,C,N,V,S 2 AND Rd, Rr Logical AND Registers Rd ← Rd • Rr Z,N,V 1 ANDI Rd, K Logical AND Register and Constant Rd ← Rd • K Z,N,V 1 OR Rd, Rr Logical OR Registers Rd ← Rd v Rr Z,N,V 1 ORI Rd, K Logical OR Register and Constant Rd ← Rd v K Z,N,V 1 EOR Rd, Rr Exclusive OR Registers Rd ← Rd ⊕ Rr Z,N,V 1 1 COM Rd One’s Complement Rd ← 0xFF − Rd Z,C,N,V 1 NEG Rd Two’s Complement Rd ← 0x00 − Rd Z,C,N,V,H 1 SBR Rd,K Set Bit(s) in Register Rd ← Rd v K Z,N,V 1 CBR Rd,K Clear Bit(s) in Register Rd ← Rd • (0xFF - K) Z,N,V 1 INC Rd Increment Rd ← Rd + 1 Z,N,V 1 DEC Rd Decrement Rd ← Rd − 1 Z,N,V 1 TST Rd Test for Zero or Minus Rd ← Rd • Rd Z,N,V 1 CLR Rd Clear Register Rd ← Rd ⊕ Rd Z,N,V 1 SER Rd Set Register Rd ← 0xFF None 1 MUL Rd, Rr Multiply Unsigned R1:R0 ← Rd x Rr Z,C 2 MULS Rd, Rr Multiply Signed R1:R0 ← Rd x Rr Z,C 2 MULSU Rd, Rr Multiply Signed with Unsigned R1:R0 ← Rd x Rr Z,C 2 FMUL Rd, Rr Fractional Multiply Unsigned R1:R0 ← (Rd x Rr) << 1 Z,C 2 FMULS Rd, Rr Fractional Multiply Signed R1:R0 ← (Rd x Rr) << 1 Z,C 2 FMULSU Rd, Rr Fractional Multiply Signed with Unsigned R1:R0 ← (Rd x Rr) << 1 Z,C 2 2 BRANCH INSTRUCTIONS RJMP k IJMP Relative Jump PC ← PC + k + 1 None Indirect Jump to (Z) PC ← Z None 2 JMP(1) k Direct Jump PC ← k None 3 RCALL k Relative Subroutine Call PC ← PC + k + 1 None 3 Indirect Call to (Z) PC ← Z None 3 Direct Subroutine Call PC ← k None 4 RET Subroutine Return PC ← STACK None 4 RETI Interrupt Return PC ← STACK I 4 ICALL CALL(1) k CPSE Rd,Rr Compare, Skip if Equal if (Rd = Rr) PC ← PC + 2 or 3 None CP Rd,Rr Compare Rd − Rr Z, N,V,C,H 1 CPC Rd,Rr Compare with Carry Rd − Rr − C Z, N,V,C,H 1 CPI Rd,K Compare Register with Immediate Rd − K Z, N,V,C,H SBRC Rr, b Skip if Bit in Register Cleared if (Rr(b)=0) PC ← PC + 2 or 3 None 1/2/3 1/2/3 1 SBRS Rr, b Skip if Bit in Register is Set if (Rr(b)=1) PC ← PC + 2 or 3 None 1/2/3 SBIC P, b Skip if Bit in I/O Register Cleared if (P(b)=0) PC ← PC + 2 or 3 None 1/2/3 SBIS P, b Skip if Bit in I/O Register is Set if (P(b)=1) PC ← PC + 2 or 3 None 1/2/3 BRBS s, k Branch if Status Flag Set if (SREG(s) = 1) then PC←PC+k + 1 None 1/2 BRBC s, k Branch if Status Flag Cleared if (SREG(s) = 0) then PC←PC+k + 1 None 1/2 BREQ k Branch if Equal if (Z = 1) then PC ← PC + k + 1 None 1/2 BRNE k Branch if Not Equal if (Z = 0) then PC ← PC + k + 1 None 1/2 BRCS k Branch if Carry Set if (C = 1) then PC ← PC + k + 1 None 1/2 BRCC k Branch if Carry Cleared if (C = 0) then PC ← PC + k + 1 None 1/2 BRSH k Branch if Same or Higher if (C = 0) then PC ← PC + k + 1 None 1/2 BRLO k Branch if Lower if (C = 1) then PC ← PC + k + 1 None 1/2 BRMI k Branch if Minus if (N = 1) then PC ← PC + k + 1 None 1/2 BRPL k Branch if Plus if (N = 0) then PC ← PC + k + 1 None 1/2 BRGE k Branch if Greater or Equal, Signed if (N ⊕ V= 0) then PC ← PC + k + 1 None 1/2 BRLT k Branch if Less Than Zero, Signed if (N ⊕ V= 1) then PC ← PC + k + 1 None 1/2 BRHS k Branch if Half Carry Flag Set if (H = 1) then PC ← PC + k + 1 None 1/2 BRHC k Branch if Half Carry Flag Cleared if (H = 0) then PC ← PC + k + 1 None 1/2 BRTS k Branch if T Flag Set if (T = 1) then PC ← PC + k + 1 None 1/2 BRTC k Branch if T Flag Cleared if (T = 0) then PC ← PC + k + 1 None 1/2 BRVS k Branch if Overflow Flag is Set if (V = 1) then PC ← PC + k + 1 None 1/2 BRVC k Branch if Overflow Flag is Cleared if (V = 0) then PC ← PC + k + 1 None 1/2 12 8271BS–AVR–04/10 ATmega48A/48PA/88A/88PA/168A/168PA/328/328P Mnemonics Operands Description Operation Flags #Clocks BRIE k Branch if Interrupt Enabled if ( I = 1) then PC ← PC + k + 1 None 1/2 BRID k Branch if Interrupt Disabled if ( I = 0) then PC ← PC + k + 1 None 1/2 BIT AND BIT-TEST INSTRUCTIONS SBI P,b Set Bit in I/O Register I/O(P,b) ← 1 None 2 CBI P,b Clear Bit in I/O Register I/O(P,b) ← 0 None 2 LSL Rd Logical Shift Left Rd(n+1) ← Rd(n), Rd(0) ← 0 Z,C,N,V 1 LSR Rd Logical Shift Right Rd(n) ← Rd(n+1), Rd(7) ← 0 Z,C,N,V 1 ROL Rd Rotate Left Through Carry Rd(0)←C,Rd(n+1)← Rd(n),C←Rd(7) Z,C,N,V 1 ROR Rd Rotate Right Through Carry Rd(7)←C,Rd(n)← Rd(n+1),C←Rd(0) Z,C,N,V 1 ASR Rd Arithmetic Shift Right Rd(n) ← Rd(n+1), n=0...6 Z,C,N,V 1 SWAP Rd Swap Nibbles Rd(3...0)←Rd(7...4),Rd(7...4)←Rd(3...0) None 1 BSET s Flag Set SREG(s) ← 1 SREG(s) 1 BCLR s Flag Clear SREG(s) ← 0 SREG(s) 1 BST Rr, b Bit Store from Register to T T ← Rr(b) T 1 BLD Rd, b Bit load from T to Register Rd(b) ← T None 1 SEC Set Carry C←1 C 1 CLC Clear Carry C←0 C 1 SEN Set Negative Flag N←1 N 1 CLN Clear Negative Flag N←0 N 1 SEZ Set Zero Flag Z←1 Z 1 CLZ Clear Zero Flag Z←0 Z 1 SEI Global Interrupt Enable I←1 I 1 CLI Global Interrupt Disable I←0 I 1 SES Set Signed Test Flag S←1 S 1 CLS Clear Signed Test Flag S←0 S 1 SEV Set Twos Complement Overflow. V←1 V 1 CLV Clear Twos Complement Overflow V←0 V 1 SET Set T in SREG T←1 T 1 CLT Clear T in SREG T←0 T 1 SEH Set Half Carry Flag in SREG H←1 H 1 CLH Clear Half Carry Flag in SREG H←0 H 1 Rd ← Rr Rd+1:Rd ← Rr+1:Rr None 1 None 1 1 DATA TRANSFER INSTRUCTIONS MOV Rd, Rr Move Between Registers MOVW Rd, Rr Copy Register Word LDI Rd, K Load Immediate Rd ← K None LD Rd, X Load Indirect Rd ← (X) None 2 LD Rd, X+ Load Indirect and Post-Inc. Rd ← (X), X ← X + 1 None 2 2 LD Rd, - X Load Indirect and Pre-Dec. X ← X - 1, Rd ← (X) None LD Rd, Y Load Indirect Rd ← (Y) None 2 LD Rd, Y+ Load Indirect and Post-Inc. Rd ← (Y), Y ← Y + 1 None 2 LD Rd, - Y Load Indirect and Pre-Dec. Y ← Y - 1, Rd ← (Y) None 2 LDD Rd,Y+q Load Indirect with Displacement Rd ← (Y + q) None 2 LD Rd, Z Load Indirect Rd ← (Z) None 2 LD Rd, Z+ Load Indirect and Post-Inc. Rd ← (Z), Z ← Z+1 None 2 LD Rd, -Z Load Indirect and Pre-Dec. Z ← Z - 1, Rd ← (Z) None 2 LDD Rd, Z+q Load Indirect with Displacement Rd ← (Z + q) None 2 LDS Rd, k Load Direct from SRAM Rd ← (k) None 2 ST X, Rr Store Indirect (X) ← Rr None 2 ST X+, Rr Store Indirect and Post-Inc. (X) ← Rr, X ← X + 1 None 2 ST - X, Rr Store Indirect and Pre-Dec. X ← X - 1, (X) ← Rr None 2 ST Y, Rr Store Indirect (Y) ← Rr None 2 ST Y+, Rr Store Indirect and Post-Inc. (Y) ← Rr, Y ← Y + 1 None 2 ST - Y, Rr Store Indirect and Pre-Dec. Y ← Y - 1, (Y) ← Rr None 2 STD Y+q,Rr Store Indirect with Displacement (Y + q) ← Rr None 2 ST Z, Rr Store Indirect (Z) ← Rr None 2 ST Z+, Rr Store Indirect and Post-Inc. (Z) ← Rr, Z ← Z + 1 None 2 ST -Z, Rr Store Indirect and Pre-Dec. Z ← Z - 1, (Z) ← Rr None 2 STD Z+q,Rr Store Indirect with Displacement (Z + q) ← Rr None 2 STS k, Rr Store Direct to SRAM (k) ← Rr None 2 Load Program Memory R0 ← (Z) None 3 LPM LPM Rd, Z Load Program Memory Rd ← (Z) None 3 LPM Rd, Z+ Load Program Memory and Post-Inc Rd ← (Z), Z ← Z+1 None 3 Store Program Memory (Z) ← R1:R0 None - IN Rd, P In Port Rd ← P None 1 OUT P, Rr Out Port P ← Rr None 1 PUSH Rr Push Register on Stack STACK ← Rr None 2 SPM 13 8271BS–AVR–04/10 ATmega48A/48PA/88A/88PA/168A/168PA/328/328P Mnemonics POP Operands Rd Description Pop Register from Stack Operation Rd ← STACK Flags #Clocks None 2 MCU CONTROL INSTRUCTIONS NOP No Operation None 1 SLEEP Sleep (see specific descr. for Sleep function) None 1 WDR BREAK Watchdog Reset Break (see specific descr. for WDR/timer) For On-chip Debug Only None None 1 N/A Note: 1. These instructions are only available in ATmega168PA and ATmega328P. 14 8271BS–AVR–04/10 ATmega48A/48PA/88A/88PA/168A/168PA/328/328P 6. Ordering Information 6.1 ATmega48A Speed (MHz) 20(3) Note: Power Supply 1.8 - 5.5 Ordering Code(2) Package(1) ATmega48A-AU ATmega48A-AUR(5) ATmega48A-MMH(4) ATmega48A-MMHR(4)(5) ATmega48A-MU ATmega48A-MUR(5) ATmega48A-PU 32A 32A 28M1 28M1 32M1-A 32M1-A 28P3 Operational Range Industrial (-40°C to 85°C) 1. This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering information and minimum quantities. 2. Pb-free packaging complies to the European Directive for Restriction of Hazardous Substances (RoHS directive).Also Halide free and fully Green. 3. See ”Speed Grades” on page 321. 4. NiPdAu Lead Finish. 5. Tape & Reel. Package Type 32A 32-lead, Thin (1.0 mm) Plastic Quad Flat Package (TQFP) 28M1 28-pad, 4 x 4 x 1.0 body, Lead Pitch 0.45 mm Quad Flat No-Lead/Micro Lead Frame Package (QFN/MLF) 32M1-A 32-pad, 5 x 5 x 1.0 body, Lead Pitch 0.50 mm Quad Flat No-Lead/Micro Lead Frame Package (QFN/MLF) 28P3 28-lead, 0.300” Wide, Plastic Dual Inline Package (PDIP) 15 8271BS–AVR–04/10 ATmega48A/48PA/88A/88PA/168A/168PA/328/328P 6.2 ATmega48PA Speed (MHz) 20(3) Note: Power Supply 1.8 - 5.5 Ordering Code(2) Package(1) ATmega48PA-AU ATmega48PA-AUR(5) ATmega48PA-MMH(4) ATmega48PA-MMHR(4)(5) ATmega48PA-MU ATmega48PA-MUR(5) ATmega48PA-PU 32A 32A 28M1 28M1 32M1-A 32M1-A 28P3 Operational Range Industrial (-40°C to 85°C) 1. This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering information and minimum quantities. 2. Pb-free packaging complies to the European Directive for Restriction of Hazardous Substances (RoHS directive).Also Halide free and fully Green. 3. See ”Speed Grades” on page 321. 4. NiPdAu Lead Finish. 5. Tape & Reel. Package Type 32A 32-lead, Thin (1.0 mm) Plastic Quad Flat Package (TQFP) 28M1 28-pad, 4 x 4 x 1.0 body, Lead Pitch 0.45 mm Quad Flat No-Lead/Micro Lead Frame Package (QFN/MLF) 32M1-A 32-pad, 5 x 5 x 1.0 body, Lead Pitch 0.50 mm Quad Flat No-Lead/Micro Lead Frame Package (QFN/MLF) 28P3 28-lead, 0.300” Wide, Plastic Dual Inline Package (PDIP) 16 8271BS–AVR–04/10 ATmega48A/48PA/88A/88PA/168A/168PA/328/328P 6.3 ATmega88A Speed (MHz) 20(3) Note: Power Supply 1.8 - 5.5 Ordering Code(2) Package(1) ATmega88A-AU ATmega88A-AUR(5) ATmega88A-MMH(4) ATmega88A-MMHR(4)(5) ATmega88A-MU ATmega88A-MUR(5) ATmega88A-PU 32A 32A 28M1 28M1 32M1-A 32M1-A 28P3 Operational Range Industrial (-40°C to 85°C) 1. This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering information and minimum quantities. 2. Pb-free packaging complies to the European Directive for Restriction of Hazardous Substances (RoHS directive).Also Halide free and fully Green. 3. See ”Speed Grades” on page 321. 4. NiPdAu Lead Finish. 5. Tape & Reel. Package Type 32A 32-lead, Thin (1.0 mm) Plastic Quad Flat Package (TQFP) 28M1 28-pad, 4 x 4 x 1.0 body, Lead Pitch 0.45 mm Quad Flat No-Lead/Micro Lead Frame Package (QFN/MLF) 32M1-A 32-pad, 5 x 5 x 1.0 body, Lead Pitch 0.50 mm Quad Flat No-Lead/Micro Lead Frame Package (QFN/MLF) 28P3 28-lead, 0.300” Wide, Plastic Dual Inline Package (PDIP) 17 8271BS–AVR–04/10 ATmega48A/48PA/88A/88PA/168A/168PA/328/328P 6.4 ATmega88PA Speed (MHz) 20(3) Note: Power Supply (V) 1.8 - 5.5 Ordering Code(2) Package(1) ATmega88PA-AU ATmega88PA-AUR(5) ATmega88PA-MMH(4) ATmega88PA-MMHR(4)(5) ATmega88PA-MU ATmega88PA-MUR(5) ATmega88PA-PU 32A 32A 28M1 28M1 32M1-A 32M1-A 28P3 Operational Range Industrial (-40°C to 85°C) 1. This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering information and minimum quantities. 2. Pb-free packaging complies to the European Directive for Restriction of Hazardous Substances (RoHS directive).Also Halide free and fully Green. 3. See ”Speed Grades” on page 321. 4. NiPdAu Lead Finish. 5. Tape & Reel. Package Type 32A 32-lead, Thin (1.0 mm) Plastic Quad Flat Package (TQFP) 28M1 28-pad, 4 x 4 x 1.0 body, Lead Pitch 0.45 mm Quad Flat No-Lead/Micro Lead Frame Package (QFN/MLF) 32M1-A 32-pad, 5 x 5 x 1.0 body, Lead Pitch 0.50 mm Quad Flat No-Lead/Micro Lead Frame Package (QFN/MLF) 28P3 28-lead, 0.300” Wide, Plastic Dual Inline Package (PDIP) 18 8271BS–AVR–04/10 ATmega48A/48PA/88A/88PA/168A/168PA/328/328P 6.5 ATmega168A Speed (MHz)(3) 20 Note: Power Supply (V) 1.8 - 5.5 Ordering Code(2) Package(1) ATmega168A-AU ATmega168A-AUR(5) ATmega168A-MMH(4) ATmega168A-MMHR(4)(5) ATmega168A-MU ATmega168A-MUR(5) ATmega168A-PU 32A 32A 28M1 28M1 32M1-A 32M1-A 28P3 Operational Range Industrial (-40°C to 85°C) 1. This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering information and minimum quantities. 2. Pb-free packaging complies to the European Directive for Restriction of Hazardous Substances (RoHS directive).Also Halide free and fully Green. 3. See ”Speed Grades” on page 321 4. NiPdAu Lead Finish. 5. Tape & Reel. Package Type 32A 32-lead, Thin (1.0 mm) Plastic Quad Flat Package (TQFP) 28M1 28-pad, 4 x 4 x 1.0 body, Lead Pitch 0.45 mm Quad Flat No-Lead/Micro Lead Frame Package (QFN/MLF) 32M1-A 32-pad, 5 x 5 x 1.0 body, Lead Pitch 0.50 mm Quad Flat No-Lead/Micro Lead Frame Package (QFN/MLF) 28P3 28-lead, 0.300” Wide, Plastic Dual Inline Package (PDIP) 19 8271BS–AVR–04/10 ATmega48A/48PA/88A/88PA/168A/168PA/328/328P 6.6 ATmega168PA Speed (MHz)(3) 20 Note: Power Supply (V) 1.8 - 5.5 Ordering Code(2) Package(1) ATmega168PA-AU ATmega168PA-AUR(5) ATmega168PA-MMH(4) ATmega168PA-MMHR(4)(5) ATmega168PA-MU ATmega168PA-MUR(5) ATmega168PA-PU 32A 32A 28M1 28M1 32M1-A 32M1-A 28P3 Operational Range Industrial (-40°C to 85°C) 1. This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering information and minimum quantities. 2. Pb-free packaging complies to the European Directive for Restriction of Hazardous Substances (RoHS directive).Also Halide free and fully Green. 3. See ”Speed Grades” on page 321. 4. NiPdAu Lead Finish. 5. Tape & Reel. Package Type 32A 32-lead, Thin (1.0 mm) Plastic Quad Flat Package (TQFP) 28M1 28-pad, 4 x 4 x 1.0 body, Lead Pitch 0.45 mm Quad Flat No-Lead/Micro Lead Frame Package (QFN/MLF) 32M1-A 32-pad, 5 x 5 x 1.0 body, Lead Pitch 0.50 mm Quad Flat No-Lead/Micro Lead Frame Package (QFN/MLF) 28P3 28-lead, 0.300” Wide, Plastic Dual Inline Package (PDIP) 20 8271BS–AVR–04/10 ATmega48A/48PA/88A/88PA/168A/168PA/328/328P 6.7 ATmega328 Speed (MHz) 20(3) Note: Power Supply (V) 1.8 - 5.5 Ordering Code(2) Package(1) ATmega328-AU ATmega328-AUR(4) ATmega328-MU ATmega328-MUR(4) ATmega328-PU 32A 32A 32M1-A 32M1-A 28P3 Operational Range Industrial (-40°C to 85°C) 1. This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering information and minimum quantities. 2. Pb-free packaging complies to the European Directive for Restriction of Hazardous Substances (RoHS directive).Also Halide free and fully Green. 3. See Figure 28-1 on page 321. 4. Tape & Reel Package Type 32A 32-lead, Thin (1.0 mm) Plastic Quad Flat Package (TQFP) 28P3 28-lead, 0.300” Wide, Plastic Dual Inline Package (PDIP) 32M1-A 32-pad, 5 x 5 x 1.0 body, Lead Pitch 0.50 mm Quad Flat No-Lead/Micro Lead Frame Package (QFN/MLF) 21 8271BS–AVR–04/10 ATmega48A/48PA/88A/88PA/168A/168PA/328/328P 6.8 ATmega328P Speed (MHz) 20(3) Note: Power Supply 1.8 - 5.5 Ordering Code(2) Package(1) ATmega328P-AU ATmega328P-AUR(4) ATmega328P-MU ATmega328P-MUR(4) ATmega328P-PU 32A 32A 32M1-A 32M1-A 28P3 Operational Range Industrial (-40°C to 85°C) 1. This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering information and minimum quantities. 2. Pb-free packaging complies to the European Directive for Restriction of Hazardous Substances (RoHS directive).Also Halide free and fully Green. 3. See Figure 28-1 on page 321. 4. Tape & Reel. Package Type 32A 32-lead, Thin (1.0 mm) Plastic Quad Flat Package (TQFP) 28P3 28-lead, 0.300” Wide, Plastic Dual Inline Package (PDIP) 32M1-A 32-pad, 5 x 5 x 1.0 body, Lead Pitch 0.50 mm Quad Flat No-Lead/Micro Lead Frame Package (QFN/MLF) 22 8271BS–AVR–04/10 ATmega48A/48PA/88A/88PA/168A/168PA/328/328P 7. Packaging Information 7.1 32A PIN 1 B PIN 1 IDENTIFIER E1 e E D1 D C 0˚~7˚ A1 A2 A L COMMON DIMENSIONS (Unit of Measure = mm) Notes: 1. This package conforms to JEDEC reference MS-026, Variation ABA. 2. Dimensions D1 and E1 do not include mold protrusion. Allowable protrusion is 0.25 mm per side. Dimensions D1 and E1 are maximum plastic body size dimensions including mold mismatch. 3. Lead coplanarity is 0.10 mm maximum. SYMBOL MIN NOM MAX A – – 1.20 A1 0.05 – 0.15 A2 0.95 1.00 1.05 D 8.75 9.00 9.25 D1 6.90 7.00 7.10 E 8.75 9.00 9.25 E1 6.90 7.00 7.10 B 0.30 – 0.45 C 0.09 – 0.20 L 0.45 – 0.75 e NOTE Note 2 Note 2 0.80 TYP 10/5/2001 R 2325 Orchard Parkway San Jose, CA 95131 TITLE 32A, 32-lead, 7 x 7 mm Body Size, 1.0 mm Body Thickness, 0.8 mm Lead Pitch, Thin Profile Plastic Quad Flat Package (TQFP) DRAWING NO. REV. 32A B 23 8271BS–AVR–04/10 ATmega48A/48PA/88A/88PA/168A/168PA/328/328P 7.2 28M1 D C 1 2 Pin 1 ID 3 E SIDE VIEW A1 TOP VIEW A y D2 K 1 0.45 2 R 0.20 3 E2 b COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX A 0.80 0.90 1.00 A1 0.00 0.02 0.05 b 0.17 0.22 0.27 C L e 0.4 Ref (4x) Note: 0.20 REF D 3.95 4.00 4.05 D2 2.35 2.40 2.45 E 3.95 4.00 4.05 E2 2.35 2.40 2.45 e BOTTOM VIEW The terminal #1 ID is a Laser-marked Feature. NOTE 0.45 L 0.35 0.40 0.45 y 0.00 – 0.08 K 0.20 – – 10/24/08 Package Drawing Contact: [email protected] TITLE 28M1, 28-pad, 4 x 4 x 1.0 mm Body, Lead Pitch 0.45 mm, 2.4 x 2.4 mm Exposed Pad, Thermally Enhanced Plastic Very Thin Quad Flat No Lead Package (VQFN) GPC ZBV DRAWING NO. REV. 28M1 B 24 8271BS–AVR–04/10 ATmega48A/48PA/88A/88PA/168A/168PA/328/328P 7.3 32M1-A D D1 1 2 3 0 Pin 1 ID E1 SIDE VIEW E TOP VIEW A3 A2 A1 A K 0.08 C P D2 1 2 3 P Pin #1 Notch (0.20 R) K e SYMBOL MIN NOM MAX A 0.80 0.90 1.00 A1 – 0.02 0.05 A2 – 0.65 1.00 A3 E2 b COMMON DIMENSIONS (Unit of Measure = mm) L BOTTOM VIEW 0.20 REF b 0.18 0.23 0.30 D 4.90 5.00 5.10 D1 4.70 4.75 4.80 D2 2.95 3.10 3.25 E 4.90 5.00 5.10 E1 4.70 4.75 4.80 E2 2.95 3.10 3.25 e Note: JEDEC Standard MO-220, Fig. 2 (Anvil Singulation), VHHD-2. NOTE 0.50 BSC L 0.30 0.40 0.50 P – – 0 – – 0.60 12o K 0.20 – – 5/25/06 R 2325 Orchard Parkway San Jose, CA 95131 TITLE 32M1-A, 32-pad, 5 x 5 x 1.0 mm Body, Lead Pitch 0.50 mm, 3.10 mm Exposed Pad, Micro Lead Frame Package (MLF) DRAWING NO. 32M1-A REV. E 25 8271BS–AVR–04/10 ATmega48A/48PA/88A/88PA/168A/168PA/328/328P 7.4 28P3 D PIN 1 E1 A SEATING PLANE L B2 B1 A1 B (4 PLACES) 0º ~ 15º REF e E C COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL eB Note: 1. Dimensions D and E1 do not include mold Flash or Protrusion. Mold Flash or Protrusion shall not exceed 0.25 mm (0.010"). A MIN – NOM MAX – 4.5724 A1 0.508 – – D 34.544 – 34.798 E 7.620 – 8.255 E1 7.112 – 7.493 B 0.381 – 0.533 B1 1.143 – 1.397 B2 0.762 – 1.143 L 3.175 – 3.429 C 0.203 – 0.356 eB – – 10.160 e NOTE Note 1 Note 1 2.540 TYP 09/28/01 R 2325 Orchard Parkway San Jose, CA 95131 TITLE 28P3, 28-lead (0.300"/7.62 mm Wide) Plastic Dual Inline Package (PDIP) DRAWING NO. 28P3 REV. B 26 8271BS–AVR–04/10 ATmega48A/48PA/88A/88PA/168A/168PA/328/328P 8. Errata 8.1 Errata ATmega48A The revision letter in this section refers to the revision of the ATmega48A device. 8.1.1 Rev. D • Analog MUX can be turned off when setting ACME bit 1. Analog MUX can be turned off when setting ACME bit If the ACME (Analog Comparator Multiplexer Enabled) bit in ADCSRB is set while MUX3 in ADMUX is '1' (ADMUX[3:0]=1xxx), all MUX'es are turned off until the ACME bit is cleared. Problem Fix/Workaround Clear the MUX3 bit before setting the ACME bit. 8.2 Errata ATmega48PA The revision letter in this section refers to the revision of the ATmega48PA device. 8.2.1 Rev. D • Analog MUX can be turned off when setting ACME bit 1. Analog MUX can be turned off when setting ACME bit If the ACME (Analog Comparator Multiplexer Enabled) bit in ADCSRB is set while MUX3 in ADMUX is '1' (ADMUX[3:0]=1xxx), all MUX'es are turned off until the ACME bit is cleared. Problem Fix/Workaround Clear the MUX3 bit before setting the ACME bit. 8.3 Errata ATmega88A The revision letter in this section refers to the revision of the ATmega88A device. 8.3.1 Rev. F • Analog MUX can be turned off when setting ACME bit 1. Analog MUX can be turned off when setting ACME bit If the ACME (Analog Comparator Multiplexer Enabled) bit in ADCSRB is set while MUX3 in ADMUX is '1' (ADMUX[3:0]=1xxx), all MUX'es are turned off until the ACME bit is cleared. Problem Fix/Workaround Clear the MUX3 bit before setting the ACME bit. 27 8271BS–AVR–04/10 ATmega48A/48PA/88A/88PA/168A/168PA/328/328P 8.4 Errata ATmega88PA The revision letter in this section refers to the revision of the ATmega88PA device. 8.4.1 Rev. F • Analog MUX can be turned off when setting ACME bit 1. Analog MUX can be turned off when setting ACME bit If the ACME (Analog Comparator Multiplexer Enabled) bit in ADCSRB is set while MUX3 in ADMUX is '1' (ADMUX[3:0]=1xxx), all MUX'es are turned off until the ACME bit is cleared. Problem Fix/Workaround Clear the MUX3 bit before setting the ACME bit. 8.5 Errata ATmega168A The revision letter in this section refers to the revision of the ATmega168A device. 8.5.1 Rev. E • Analog MUX can be turned off when setting ACME bit 1. Analog MUX can be turned off when setting ACME bit If the ACME (Analog Comparator Multiplexer Enabled) bit in ADCSRB is set while MUX3 in ADMUX is '1' (ADMUX[3:0]=1xxx), all MUX'es are turned off until the ACME bit is cleared. Problem Fix/Workaround Clear the MUX3 bit before setting the ACME bit. 8.6 Errata ATmega168PA The revision letter in this section refers to the revision of the ATmega168PA device. 8.6.1 Rev E • Analog MUX can be turned off when setting ACME bit 1. Analog MUX can be turned off when setting ACME bit If the ACME (Analog Comparator Multiplexer Enabled) bit in ADCSRB is set while MUX3 in ADMUX is '1' (ADMUX[3:0]=1xxx), all MUX'es are turned off until the ACME bit is cleared. Problem Fix/Workaround Clear the MUX3 bit before setting the ACME bit. 28 8271BS–AVR–04/10 ATmega48A/48PA/88A/88PA/168A/168PA/328/328P 8.7 Errata ATmega328 The revision letter in this section refers to the revision of the ATmega328 device. 8.7.1 Rev D • Analog MUX can be turned off when setting ACME bit 1. Analog MUX can be turned off when setting ACME bit If the ACME (Analog Comparator Multiplexer Enabled) bit in ADCSRB is set while MUX3 in ADMUX is '1' (ADMUX[3:0]=1xxx), all MUX'es are turned off until the ACME bit is cleared. Problem Fix/Workaround Clear the MUX3 bit before setting the ACME bit. 8.7.2 Rev C Not sampled. 8.7.3 Rev B • Analog MUX can be turned off when setting ACME bit • Unstable 32 kHz Oscillator 1. Unstable 32 kHz Oscillator If the ACME (Analog Comparator Multiplexer Enabled) bit in ADCSRB is set while MUX3 in ADMUX is '1' (ADMUX[3:0]=1xxx), all MUX'es are turned off until the ACME bit is cleared. Problem Fix/Workaround Clear the MUX3 bit before setting the ACME bit. 2. Unstable 32 kHz Oscillator The 32 kHz oscillator does not work as system clock. The 32 kHz oscillator used as asynchronous timer is inaccurate. Problem Fix/ Workaround None. 8.7.4 Rev A • Analog MUX can be turned off when setting ACME bit • Unstable 32 kHz Oscillator 1. Unstable 32 kHz Oscillator If the ACME (Analog Comparator Multiplexer Enabled) bit in ADCSRB is set while MUX3 in ADMUX is '1' (ADMUX[3:0]=1xxx), all MUX'es are turned off until the ACME bit is cleared. Problem Fix/Workaround Clear the MUX3 bit before setting the ACME bit. 2. Unstable 32 kHz Oscillator The 32 kHz oscillator does not work as system clock. The 32 kHz oscillator used as asynchronous timer is inaccurate. Problem Fix/ Workaround None. 29 8271BS–AVR–04/10 ATmega48A/48PA/88A/88PA/168A/168PA/328/328P 8.8 Errata ATmega328P The revision letter in this section refers to the revision of the ATmega328P device. 8.8.1 Rev D • Analog MUX can be turned off when setting ACME bit 1. Analog MUX can be turned off when setting ACME bit If the ACME (Analog Comparator Multiplexer Enabled) bit in ADCSRB is set while MUX3 in ADMUX is '1' (ADMUX[3:0]=1xxx), all MUX'es are turned off until the ACME bit is cleared. Problem Fix/Workaround Clear the MUX3 bit before setting the ACME bit. 8.8.2 Rev C Not sampled. 8.8.3 Rev B • Analog MUX can be turned off when setting ACME bit • Unstable 32 kHz Oscillator 1. Unstable 32 kHz Oscillator If the ACME (Analog Comparator Multiplexer Enabled) bit in ADCSRB is set while MUX3 in ADMUX is '1' (ADMUX[3:0]=1xxx), all MUX'es are turned off until the ACME bit is cleared. Problem Fix/Workaround Clear the MUX3 bit before setting the ACME bit. 2. Unstable 32 kHz Oscillator The 32 kHz oscillator does not work as system clock. The 32 kHz oscillator used as asynchronous timer is inaccurate. Problem Fix/ Workaround None. 8.8.4 Rev A • Unstable 32 kHz Oscillator 1. Unstable 32 kHz Oscillator The 32 kHz oscillator does not work as system clock. The 32 kHz oscillator used as asynchronous timer is inaccurate. Problem Fix/ Workaround None. 30 8271BS–AVR–04/10 ATmega48A/48PA/88A/88PA/168A/168PA/328/328P 9. Datasheet Revision History Please note that the referring page numbers in this section are referred to this document. The referring revision in this section are referring to the document revision. 9.1 Rev. 8271B-04/10 1. 2. 3. 4. 5. 9.2 Updated Table 8-8 with correct value for timer oscilliator at xtal2/tos2 Corrected use of SBIS instructions in assembly code examples. Corrected BOD and BODSE bits to R/W in Section 9.11.2 on page 45, Section 11.5 on page 69 and Section 13.4 on page 93 Figures for bandgap characterization added, Figure 29-34 on page 349, Figure 29-81 on page 374, Figure 29-128 on page 399, Figure 29-175 on page 424, Figure 29-222 on page 449, Figure 29-269 on page 474, Figure 29-316 on page 499 and Figure 29-363 on page 523. Updated ”Packaging Information” on page 546 by replacing 28M1 with a correct corresponding package. Rev. 8271A-12/09 1. 2 New datasheet 8271 with merged information for ATmega48PA, ATmega88PA, ATmega168PA and ATmega48A, ATmega88A andATmega168A. Also included information on ATmega328 and ATmega328P Changes done: – New devices added: ATmega48A/ATmega88A/ATmega168A and ATmega328 – Updated Feature Description – Updated Table 2-1 on page 6 – Added note for BOD Disable on page 40. – Added note on BOD and BODSE in ”MCUCR – MCU Control Register” on page 93 and ”Register Description” on page 294 – Added limitation informatin for the application ”Boot Loader Support – Read-While-Write Self-Programming” on page 279 – Added limitiation information for ”Program And Data Memory Lock Bits” on page 296 – Added specified DC characteristice per processor – Added typical characteristics per processor – Removed execption information in ”Address Match Unit” on page 223. 31 8271BS–AVR–04/10 Headquarters International Atmel Corporation 2325 Orchard Parkway San Jose, CA 95131 USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Atmel Asia Unit 1-5 & 16, 19/F BEA Tower, Millennium City 5 418 Kwun Tong Road Kwun Tong, Kowloon Hong Kong Tel: (852) 2245-6100 Fax: (852) 2722-1369 Atmel Europe Le Krebs 8, Rue Jean-Pierre Timbaud BP 309 78054 Saint-Quentin-enYvelines Cedex France Tel: (33) 1-30-60-70-00 Fax: (33) 1-30-60-71-11 Atmel Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 Technical Support [email protected] Sales Contact www.atmel.com/contacts Product Contact Web Site www.atmel.com Literature Requests www.atmel.com/literature Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. © 2010 Atmel Corporation. All rights reserved. Atmel ®, Atmel logo and combinations thereof, AVR®, AVR® logo and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. 8271BS–AVR–04/10