Features • 16-channel GPS Correlator • • • • • • • • • • • • • • • • • • – 8192 Search Bins with GPS Acquisition Accelerator – Accuracy: 2.5m CEP (Stand-Alone, S/A off) – Time to First Fix: 34s (Cold Start) – Acquisition Sensitivity: –142 dBm – Tracking Sensitivity: –158 dBm Utilizes the ARM7TDMI® ARM® Thumb® Processor Core – High-performance 32-bit RISC Architecture – High-density 16-bit Instruction Set – Embedded ICE (In-circuit Emulator) 128 Kbyte Internal RAM 384 Kbyte Internal ROM with u-blox GPS Firmware 6-channel Peripheral Data Controller (PDC) 8-level Priority, Individually Maskable, Vectored Interrupt Controller – 2 External Interrupts 24 User-programmable I/O Lines 1 USB Device Port – Universal Serial Bus (USB) V2.0 Full-speed Device – Embedded USB V2.0 Full-speed Transceiver – Suspend/Resume Logic – Ping-pong Mode for Isochronous and Bulk Endpoints 2 USARTs – 2 Dedicated Peripheral Data Controller (PDC) Channels per USART Master/Slave SPI Interface – 2 Dedicated Peripheral Data Controller (PDC) Channels – 8-bit to 16-bit Programmable Data Length – 4 External Slave Chip Selects Programmable Watchdog Timer Advanced Power Management Controller (APMC) – Peripherals Can Be Deactivated Individually – Geared Master Clock to Reduce Power Consumption – Sleep State with Disabled Master Clock – Hibernate State with 32.768 kHz Master Clock Real Time Clock (RTC) 2.3V to 3.6V or 1.8V Core Supply Voltage Includes Power Supervisor 1.8V to 3.3V User-definable I/O Voltage for Several GPIOs with 5V Tolerance 4 Kbytes Battery Backup Memory 8 mm × 8 mm 56 Pin QFN56 Package Pb-free, RoHS-compliant, Green GPS Baseband Processor SuperSense ATR0625 Preliminary Rev. 4925A–GPS–02/06 1. Description The GPS baseband processor ATR0625 includes a 16-channel GPS correlator and is based on the ARM7TDMI® processor core. This processor has a high-performance 32-bit RISC architecture and very low power consumption. In addition, a large number of internally banked registers result in very fast exception handling, making the device ideal for real-time control applications. The ATR0625 has two USART and an USB device port. This port is compliant with the Universal Serial Bus (USB) V2.0 full-speed device specification. The ATR0625 includes full GPS SuperSense™ firmware, licensed from u-blox AG, which performs the basic GPS operation, including tracking, acquisition, navigation and position data output. For normal PVT (Position/Velocity/Time) applications, there is no need for off-chip Flash memory or ROM. The firmware supports the possibility to store the configuration settings in an optional external EEPROM. For customer-specific applications, a Software Development Kit is available. The ATR0625 is manufactured using Atmel’s high-density CMOS technology. By combining the ARM7TDMI microcontroller core with on-chip SRAM, 16-channel GPS correlator, and a wide range of peripheral functions on a monolithic chip, the ATR0625 provides a highly flexible and cost-effective solution for GPS applications. 2 ATR0625 [Preliminary] 4925A–GPS–02/06 ATR0625 [Preliminary] Advanced Power Management Controller XT_IN XT_OUT GPS Correlators RTC NSHDN NSLEEP GPS Accelerator ATR0625 Block Diagram SRAM RF_ON CLK23 SMD Generator P15/ANTON P0/NANTSHORT P14/NAADET1 P25/NAADET0 SIGLO0 SIGHI0 Timer Counter Figure 1-1. SPI APB PIO2 Special Function USART2 P31/RXD1 USB Transceiver USB_DP USB_DM Power Supply Manager Reset Controller JTAG NTRST NRESET ROM 384K SRAM 128K DBG_EN TDI TDO TCK TMS ARM7TDMI Embedded ICE ASB Interface to Off-Chip Memory (EBI) PDC2 B R I D G E USB Watchdog P8/STATUSLED P16/NEEPROM P22/RXD2 P18/TXD1 USART1 P30/AGCOUT0 Advanced Interrupt Controller P2/BOOT_MODE P21/TXD2 PIO2 P9/EXTINT0 PIO2 Controller P20/TIMEPULSE P29/GPSMODE12 P27/GPSMODE11 P26/GPSMODE10 P24/GPSMODE8 P23/GPSMODE7 P19/GPSMODE6 P17/GPSMODE5 P13/GPSMODE3 P12/GPSMODE2 P1/GPSMODE0 VBAT18 VBAT LDOBAT_IN LDO_OUT LDO_IN LDO_EN 3 4925A–GPS–02/06 2. Architectural Overview 2.1 Description The ATR0625 architecture consists of two main buses, the Advanced System Bus (ASB) and the Advanced Peripheral Bus (APB). The ASB is designed for maximum performance. It interfaces the processor with the on-chip 32-bit memories. The APB is designed for accesses to on-chip peripherals and is optimized for low power consumption. The AMBA™ Bridge provides an interface between the ASB and the APB. An on-chip Peripheral Data Controller (PDC2) transfers data between the on-chip USARTs/SPI and the on-chip and off-chip memories without processor intervention. Most importantly, the PDC2 removes the processor interrupt handling overhead and significantly reduces the number of clock cycles required for a data transfer. It can transfer up to 64K contiguous bytes without reprogramming the starting address. As a result, the performance of the microcontroller is increased and the power consumption reduced. The ATR0625 peripherals are designed to be easily programmable with a minimum number of instructions. Each peripheral has a 16 Kbyte address space allocated in the upper 3 Mbyte of the 4 Gbyte address space. (Except for the interrupt controller, which has 4 Kbyte address space.) The peripheral base address is the lowest address of its memory space. The peripheral register set is composed of control, mode, data, status, and interrupt registers. To maximize the efficiency of bit manipulation, frequently written registers are mapped into three memory locations. The first address is used to set the individual register bits, the second resets the bits, and the third address reads the value stored in the register. A bit can be set or reset by writing a “1” to the corresponding position at the appropriate address. Writing a “0” has no effect. Individual bits can thus be modified without having to use costly read-modifywrite and complex bit-manipulation instructions. All of the external signals of the on-chip peripherals are under the control of the Parallel I/O (PIO2) Controller. The PIO2 Controller can be programmed to insert an input filter on each pin or generate an interrupt on a signal change. After reset, the user must carefully program the PIO2 Controller in order to define which peripheral signals are connected with off-chip logic. The ARM7TDMI® processor operates in little-endian mode on the ATR0625 GPS Baseband. The processor's internal architecture and the ARM ® and Thumb ® instruction sets are described in the ARM7TDMI datasheet. The memory map and the on-chip peripherals are described in detail in the ATR0625 full datasheet. The electrical and mechanical characteristics are also documented in the ATR0625 full datasheet. The ARM standard In-Circuit Emulator (ICE) debug interface is supported via the JTAG/ICE port of the ATR0625. For features of the ROM firmware, refer to the software documentation available from u-blox AG, Switzerland. 4 ATR0625 [Preliminary] 4925A–GPS–02/06 ATR0625 [Preliminary] 3. Pin Configuration 3.1 Pinout Figure 3-1. Pinout QFN56 (Top View) 42 29 43 28 ATR0625 56 15 1 Table 3-1. 14 ATR0625 Pinout Pin Name QFN56 Pin Type CLK23 37 IN DBG_EN 8 IN GND (2) IN LDOBAT_IN 21 IN LDO_EN 25 IN LDO_IN 20 IN LDO_OUT 19 OUT NRESET 41 I/O Pull Resistor (Reset Value)(1) PIO Bank A Firmware Label I PIO Bank B O O PD Open Drain PU NSHDN 26 OUT NSLEEP 24 OUT NTRST 13 IN PD P0 40 I/O PD P1 47 I/O Configurable (PD) GPSMODE0 AGCOUT1 P2 46 I/O Configurable (PD) BOOT_MODE “0” NANTSHORT P8 48 I/O Configurable (PD) STATUSLED P9 29 I/O PU EXTINT0 P12 49 I/O Configurable (PU) GPSMODE2 P13 32 I/O PU GPSMODE3 Notes: I “0” EXTINT0 NPCS2 EXTINT1 1. PD = internal pull-down resistor, PU = internal pull-up resistor, OH = switched to Output High at reset 2. Ground plane 3. VBAT18 represent the internal power supply of the backup power domain, see section “Power Supply” on page 17. 4. VDDIO is the supply voltage for the following GPIO-pins: P1, P2, P8, P12, P14, P16, P17, P18, P19, P20, P21, P23, P24, P25, P26, P27 and P29, see section “Power Supply” on page 17. 5. VDD_USB is the supply voltage for following the USB-pins: USB_DM and USB_DP, see section “Power Supply” on page 17. For operation of the USB interface, supply of 3.0V to 3.6V is required. 6. This pin is not connected 5 4925A–GPS–02/06 Table 3-1. ATR0625 Pinout (Continued) PIO Bank A QFN56 Pin Type Pull Resistor (Reset Value)(1) Firmware Label P14 1 I/O Configurable (PD) NAADET1 P15 17 I/O PD ANTON Pin Name I PIO Bank B O I O “0” P16 6 I/O Configurable (PU) NEEPROM SIGHI1 P17 2 I/O Configurable (PD) GPSMODE5 SCK1 NWD_OVF SCK1 P18 45 I/O Configurable (PU) TXD1 P19 53 I/O Configurable (PU) GPSMODE6 SIGLO1 TXD1 P20 4 I/O Configurable (PD) TIMEPULSE SCK2 P21 52 I/O Configurable (PU) TXD2 P22 30 I/O PU RXD2 RXD2 P23 3 I/O Configurable (PU) GPSMODE7 SCK P24 5 I/O Configurable (PU) GPSMODE8 MOSI MOSI “0” P25 55 I/O Configurable (PD) NAADET0 MISO MISO “0” NSS NPCS0 “0” “0” SCK2 TIMEPULSE TXD2 “0” SCK MCLK_OUT P26 44 I/O Configurable (PU) GPSMODE10 P27 54 I/O Configurable (PU) GPSMODE11 P29 50 I/O Configurable (PU) GPSMODE12 NPCS3 P30 16 I/O PD AGCOUT0 AGCOUT0 RXD1 P31 31 I/O PU RF_ON 15 OUT PD SIGHI0 38 IN SIGLO0 39 IN TCK 9 IN PU TDI 10 IN PU TDO 11 OUT TMS 12 IN USB_DM 34 I/O USB_DP 35 I/O VBAT 22 IN VBAT18(3) 23 OUT VDD18 7, 14 IN VDD18 18, 36 IN VDD18 51 IN 43, 56 IN (4) VDDIO VDD_USB(5) 33 IN XT_IN 28 IN XT_OUT 27 OUT NC(6) 42 Notes: “0” NPCS1 “0” RXD1 PU 1. PD = internal pull-down resistor, PU = internal pull-up resistor, OH = switched to Output High at reset 2. Ground plane 3. VBAT18 represent the internal power supply of the backup power domain, see section “Power Supply” on page 17. 4. VDDIO is the supply voltage for the following GPIO-pins: P1, P2, P8, P12, P14, P16, P17, P18, P19, P20, P21, P23, P24, P25, P26, P27 and P29, see section “Power Supply” on page 17. 5. VDD_USB is the supply voltage for following the USB-pins: USB_DM and USB_DP, see section “Power Supply” on page 17. For operation of the USB interface, supply of 3.0V to 3.6V is required. 6. This pin is not connected 6 ATR0625 [Preliminary] 4925A–GPS–02/06 ATR0625 [Preliminary] 3.2 Signal Description Table 3-2. ATR0625 Signal Description Module Name EBI USART USB Function Type BOOT_MODE Boot Mode Input Input – PIO-controlled after reset, internal pull-down resistor TXD1 to TXD2 Transmit Data Output Output – PIO-controlled after reset RXD1 to RXD2 Receive Data Input Input – PIO-controlled after reset SCK1 to SCK2 PIO-controlled after reset External Synchronous Serial Clock I/O – USB_DP USB Data (D+) I/O – USB_DM USB Data (D-) I/O – Output – Input High/ Low/ Edge PIO-controlled after reset Automatic Gain Control Output – Interface to ATR0601 PIO-controlled after reset NSLEEP Sleep Output Output Low Interface to ATR0601 NSHDN Shutdown Output Output Low Connect to pin LDO_EN Input – APMC RF_ON AIC EXTINT0-1 AGC AGCOUT0-1 RTC XT_IN XT_OUT SPI External Interrupt Request Oscillator Input Oscillator Output Output – RTC oscillator I/O – PIO-controlled after reset MOSI Master Out Slave In I/O – PIO-controlled after reset MISO Master In Slave Out I/O – PIO-controlled after reset NSS/NPCS0 Slave Select I/O Low PIO-controlled after reset NPCS1 to NPCS3 Slave Select Output Low PIO-controlled after reset Output – PIO-controlled after reset I/O – Input after reset Watchdog Timer Overflow PIO P0 to P31 Programmable I/O Port SIGHI0 Digital IF Input – Interface to ATR0601 SIGLO0 Digital IF Input – Interface to ATR0601 SIGHI1 Digital IF Input – PIO-controlled after reset SIGLO1 Digital IF Input – PIO-controlled after reset TIMEPULSE Output – PIO-controlled after reset GPSMODE0-12 GPS Mode Input – PIO-controlled after reset STATUSLED Status LED Output – PIO-controlled after reset Input Low PIO-controlled after reset NEEPROM ANTON NANTSHORT NAADET0-1 Note: RTC oscillator SPI Clock NWD_OVF CONFIG Interface to ATR0601 SCK WD GPS Active Level Comment GPS synchronized time pulse Enable EEPROM Support Active antenna power on Output Output – PIO-controlled after reset Active antenna short circuit detection Input Input Low PIO-controlled after reset Active antenna detection Input Input Low PIO-controlled after reset 1. The USB transceiver is disabled if VDD_USB < 2.0V. In this case the pins USB_DM and USB_DP are connected to GND (internal pull-down resistors). The USB transceiver is enabled if VDD_USB is within 3.0V and 3.6V. 7 4925A–GPS–02/06 Table 3-2. Module ATR0625 Signal Description (Continued) Name TMS JTAG/ICE Test Data In TCK 8 Internal pull-up resistor Internal pull-up resistor – – Test Clock Input – Test Reset Input Input Low Internal pull-down resistor Debug Enable Input High Internal pull-down resistor Clock Input Input – Interface to ATR0601, Schmitt trigger input Output – PIO-controlled after reset I/O Low VDD18 Power – Core voltage 1.8V VDDIO Power – Variable IO voltage 1.65V to 3.6V VDD_USB Power – USB voltage 0 to 2.0V or 3.0V to 3.6V(1) GND Power – Ground LDOBAT_IN Power – 2.3V to 3.6V VBAT Power – 1.5V to 3.6V VBAT18 Out – 1.8V backup voltage LDO In Power – 2.3V to 3.6V LDO Out Power – 1.8V core voltage, max. 80 mA LDO Enable Input – NRESET LDO_OUT LDO_EN Note: – Input LDO_IN LDO18 Active Level Comment Output MCLK_OUT LDOBAT Input Test Data Out CLK23 POWER Test Mode Select TDI DBG_EN RESET Type TDO NTRST CLOCK Function Master Clock Output Reset Input Internal pull-up resistor Open drain with internal pull-up resistor 1. The USB transceiver is disabled if VDD_USB < 2.0V. In this case the pins USB_DM and USB_DP are connected to GND (internal pull-down resistors). The USB transceiver is enabled if VDD_USB is within 3.0V and 3.6V. ATR0625 [Preliminary] 4925A–GPS–02/06 ATR0625 [Preliminary] 3.3 Setting GPSMODE0 to GPSMODE12 The start-up configuration of a ROM-based system without external non-volatile memory is defined by the status of the GPSMODE pins after system reset. Alternatively, the system can be configured through message commands passed through the serial interface after start-up. This configuration of the ATR0625 can be stored in an external non-volatile memory like EEPROM. Default designates settings used by ROM firmware if GPSMODE configuration is disabled (GPSMODE0 = 0). Table 3-3. GPSMODE Functions Pin Function GPSMODE0 (P1) Enable configuration with GPSMODE pins GPSMODE1 (P9) This pin (EXTINT0) is used for FixNow functionality and not used for GPSMODE configuration. GPSMODE2 (P12) GPSMODE3 (P13) GPSMODE4 (P14) GPSMODE5 (P17) GPSMODE6 (P19) GPS sensitivity settings This pin (NAADET1) is used as active antenna supervisor input and not used for GPSMODE configuration. This is the default selection if GPSMODE configuration is disabled. Serial I/O configuration GPSMODE7 (P23) USB Power Mode GPSMODE8 (P24) General I/O Configuration GPSMODE9 (P25) This pin (NAADET0) is used as active antenna supervisor input and not used for GPSMODE configuration. GPSMODE10 (P26) GPSMODE11 (P27) General I/O Configuration GPSMODE12 (P29) Serial I/O configuration 3.3.1 Enable GPSMODE Pin Configuration Table 3-4. Enable Configuration with GPSMODE Pins GPSMODE0 (Reset = PD) Description 0 Ignore all GPSMODE pins. The default settings as indicated below are used. 1 Use settings as specified with GPSMODE[2, 3, 5 to 8, 10 to 12] If the GPSMODE configuration is enabled (GPSMODE0 = 1) and the other GPSMODE pins are not connected externally, the reset default values of the internal pull-down and pull-up resistors will be used. 9 4925A–GPS–02/06 3.3.2 Sensitivity Settings Table 3-5. GPSMODE3 (Fixed PU) 3.3.3 GPS Sensitivity Settings GPSMODE2 (Reset = PU) Description 0 0 Auto mode 0 1 Fast mode 1 0 Normal mode (Default ROM value) 1 1 High sensitivity Serial I/O Configuration The ATR0625 features a two-stage I/O message and protocol selection procedure for the two available serial ports. At the first stage, a certain protocol can be enabled or disabled for a given USART port or the USB port. Selectable protocols are RTCM, NMEA and UBX. At the second stage, messages can be enabled or disabled for each enabled protocol on each port. In all configurations discussed below, all protocols are enabled on all ports. But output messages are enabled in a way that ports appear to communicate at only one protocol. However, each port will accept any input message in any of the three implemented protocols Table 3-6. Serial I/O Configuration USART1/USB USART2 GPSMODE5 (Output Protocol/ (Output Protocol/ (Reset = PD) Baud Rate (kBaud)) Baud Rate (kBaud)) Messages Information Messages GPSMODE12 (Reset = PU) GPSMODE6 (Reset = PU) 0 0 0 UBX/57.6 NMEA/19.2 High User, Notice, Warning, Error 0 0 1 UBX/38.4 NMEA/9.6 Medium User, Notice, Warning, Error 0 1 0 UBX/19.2 NMEA/4.8 Low User, Notice, Warning, Error 0 1 1 –/Auto –/Auto Off None 1 0 0 NMEA/19.2 UBX/57.6 High User, Notice, Warning, Error 1 0 1 NMEA/4.8 UBX/19.2 Low User, Notice, Warning, Error 1 1 0 NMEA/9.6 UBX/38.4 Medium User, Notice, Warning, Error 1 1 1 UBX/115.2 NMEA/19.2 Debug All Both USART ports and the USB port accept input messages in all three supported protocols (NMEA, RTCM and UBX) at the configured baud rate. Input messages of all three protocols can be arbitrarily mixed. Response to a query input message will always use the same protocol as the query input message. The USB port does only accept NMEA and UBX as input protocol by default. RTCM can be enabled via protocol messages on demand. In Auto Mode, no output message is sent out by default, but all input messages are accepted at any supported baud rate. Again, USB is restricted to only NMEA and UBX protocols. Response to query input commands will be given the same protocol and baud rate as it was used for the query command. Using the respective configuration commands, periodic output messages can be enabled. 10 ATR0625 [Preliminary] 4925A–GPS–02/06 ATR0625 [Preliminary] The following message settings are used in the tables below: Table 3-7. NMEA Port UBX Port Table 3-8. NMEA Port UBX Port Table 3-9. NMEA Port UBX Port Table 3-10. NMEA Port UBX Port Supported Messages at Setting Low Standard GGA, RMC NAV SOL, SVINFO MON EXCEPT Supported Messages at Setting Medium Standard GGA, RMC, GSA, GSV, GLL, VTG, ZDA NAV SOL, SVINFO, POSECEF, POSLLH, STATUS, DOP, VELECEF, VELNED, TIMEGPS, TIMEUTC, CLOCK MON EXCEPT Supported Messages at Setting High Standard GGA, RMC, GSA, GSV, GLL, VTG, ZDA, GRS, GST Proprietary PUBX00, PUBX03, PUBX04 NAV SOL, SVINFO, POSECEF, POSLLH, STATUS, DOP, VELECEF, VELNED, TIMEGPS, TIMEUTC, CLOCK MON SCHD, IO, IPC, EXCEPT Supported Messages at Setting Debug (Additional Undocumented Message May be Part of Output Data) Standard GGA, RMC, GSA, GSV, GLL, VTG, ZDA, GRS, GST Proprietary PUBX00, PUBX03, PUBX04 NAV SOL, SVINFO, POSECEF, POSLLH, STATUS, DOP, VELECEF, VELNED, TIMEGPS, TIMEUTC, CLOCK MON SCHD, IO, IPC, EXCEPT RXM RAW (RAW message support requires an additional license) The following settings apply if GPSMODE configuration is not enabled, that is, GPSMODE = 0 (ROM-Defaults): Table 3-11. Serial I/O Default Setting if GPSMODE Configuration is Deselected (GPSMODE0 = 0) USB NMEA Baud Rate (kBaud) USART1 NMEA USART2 UBX 57.6 57.6 Input Protocol UBX, NMEA UBX, NMEA, RTCM UBX, NMEA, RTCM Output Protocol NMEA NMEA UBX Messages GGA, RMC, GSA, GSV GGA, RMC, GSA, GSV NAV: SOL, SVINFO MON: EXCEPT User, Notice, Warning, Error User, Notice, Warning, Error Information Messages User, Notice, Warning, (UBX INF or NMEA Error TXT) 11 4925A–GPS–02/06 3.3.4 USB Power Mode For correct response to the USB host queries, the device has to know its power mode. This is configured via GPSMODE7. If set to bus powered, an upper current limit of 100 mA is reported to the USB host; that is, the device classifies itself as a “low-power bus-powered function” with no more than one USB power unit load. Table 3-12. USB Power Modes GPSMODE7 (Reset = PU) Description 3.3.5 0 USB device is bus-powered (max. current limit 100 mA) 1 USB device is self-powered (Default ROM value) Active Antenna Supervisor The two pins P0/NANTSHORT and P15/ANTON plus one pin of P25/NAADET0/MISO or P14/NAADET1 are always initialized as general purpose I/Os and used as follows: • P15/ANTON is an output which can be used to switch on and off antenna power supply. • Input P0/NANTSHORT will indicate an antenna short circuit, i.e. zero DC voltage at the antenna, to the firmware. If the antenna is switched off by output P15/ANTON, it is assumed that also input P0/NANTSHORT will signal zero DC voltage, i.e. switch to its active low state. • Input P25/NAADET0/MISO or P14/NAADET1 will indicate a DC current into the antenna. In case of short circuit, both P0 and P25/P14 will be active, i.e. at low level. If the antenna is switched off by output P15/ANTON, it is assumed that also input P25/NAADET0/MISO will signal zero DC current, i.e. switch to its active low state. Which pin is used as NAADET (P14 or P25) depends on the settings of GPSMODE11 and GPSMODE10 (see Table 3-14 on page 13). Table 3-13. 12 Pin Usage of Active Antenna Supervisor Pin Usage Meaning P0/NANTSHORT NANTSHORT Active antenna short circuit detection High = No antenna DC short circuit present Low = Antenna DC short circuit present P25/NAADET0/ MISO or P14/NAADET1 NAADET Active antenna detection input High = No active antenna present Low = Active antenna is present P15/ANTON ANTON Active antenna power on output High = Power supply to active antenna is switched on Low = Power supply to active antenna is switched off ATR0625 [Preliminary] 4925A–GPS–02/06 ATR0625 [Preliminary] Table 3-14. Antenna Detection I/O Settings GPSMODE11 GPSMODE10 GPSMODE8 (Reset = PU) (Reset = PU) (Reset = PU) Location of NAADET Comment 0 0 0 P25/NAADET0/MISO 0 0 1 P25/NAADET0/MISO 0 1 0 P14/NAADET1 0 1 1 P14/NAADET1 (Default ROM value) 1 0 0 P14/NAADET1 Reserved for further use. Do not use this setting. 1 0 1 P14/NAADET1 Reserved for further use. Do not use this setting. 1 1 0 P25/NAADET0/MISO 1 1 1 P25/NAADET0/MISO Reserved for further use. Do not use this setting. The Antenna Supervisor Software will be configured as follows: 1. Enable Control Signal 2. Enable Short Circuit Detection (power down antenna via ANTON if short is detected via NANTSHORT) 3. Enable Open Circuit Detection via NAADET The antenna supervisor function may not be disabled by GPSMODE pin selection. 13 4925A–GPS–02/06 3.4 External Connections for a Working GPS System Figure 3-2. Example of an External Connection ATR0601 SIGH SIGL SC PURF PUXTO SIGHI SIGLO CLK23 RF_ON NSLEEP NC see Table 3-15 see Table 3-15 see Table 3-15 see Table 3-15 see Table 3-15 see Table 3-15 NRESET P0 - 2 P9 P12 - 17 P19 P23 - 27 P29 - 30 NC NC NC NC NC TMS TCK TDI NTRST TDO NC DBG_EN GND +3V (see Power Supply) GND NSHDN LDO_EN LDO_OUT VDD18 LDO_IN LDOBAT_IN ATR0625 P8 P20 STATUS LED TIMEPULSE USB_DM USB_DP Optional USB P31 P18 Optional USART 1 P22 P21 Optional USART 2 XT_IN XT_OUT 32.368 kHz (see RTC) +3V (see Power Supply) VDDIO +3V (see Power Supply) VBAT18 VBAT VDD_USB +3V (see Power Supply) GND NC: Not connected 14 ATR0625 [Preliminary] 4925A–GPS–02/06 ATR0625 [Preliminary] Table 3-15. Recommended Pin Connection Pin Name Recommended External Circuit P0/NANTSHORT Internal pull-down resistor, leave open if Antenna Supervision functionality is unused. Can be left open if configured as output by user application. P1/GPSMODE0 Internal pull-down resistor, leave open, in order to disable the GPSMODE pin configuration feature. Connect to VDDIO to enable the GPSMODE pin configuration feature. Refer to GPSMODE definitions in section “Setting GPSMODE0 to GPSMODE12” on page 9. Can be left open if configured as output by user application. P2/BOOT_MODE Internal pull-down resistor, leave open. P8/STATUSLED Output in default ROM firmware: leave open, only needs pull-up resistor to VDDIO or pull-down resistor to GND if used as GPIO input by user application and is not always driven from external sources. P9/EXTINT0 Internal pull-up resistor, leave open if unused. Internal pull-up resistor, can be left open if the GPSMODE feature is not used or configured as output by user P12/GPSMODE2/NPCS2 application. Refer to GPSMODE definitions in section “Setting GPSMODE0 to GPSMODE12” on page 9. P13/GPSMODE3/ EXTINT1 Internal pull-up resistor, can be left open if the GPSMODE feature is not used or configured as output by user application. Refer to GPSMODE definitions in section “Setting GPSMODE0 to GPSMODE12” on page 9. P14/NAADET1 Internal pull-down resistor, leave open if Antenna Supervision functionality is unused. Can be left open if configured as output by user application. P15/ANTON Internal pull-down resistor, leave open if Antenna Supervision functionality is unused. Can be left open if configured as output by user application. P16/NEEPROM Internal pull-up resistor, leave open if no serial EEPROM is connected. Otherwise connect to GND. P17/GPSMODE5/SCK1 Internal pull-down resistor, can be left open if the GPSMODE feature is not used or configured as output by user application. Refer to GPSMODE definitions in section “Setting GPSMODE0 to GPSMODE12” on page 9. P18/TXD1 Output in default ROM firmware: leave open if serial interface is not used. Internal pull-up resistor, can be left open if the GPSMODE feature is not used or configured as output by user P19/GPSMODE6/SIGLO1 application. Refer to GPSMODE definitions in section “Setting GPSMODE0 to GPSMODE12” on page 9. P20/TIMEPULSE/SCK2 Output in default ROM firmware: leave open if timepulse feature is not used. P21/TXD2 Output in default ROM firmware: leave open if serial interface not used. P22/RXD2 Internal pull-up resistor, leave open if serial interface is not used. P23/GPSMODE7/SCK Internal pull-up resistor, can be left open if the GPSMODE feature is not used or configured as output by user application. Refer to GPSMODE definitions in section “Setting GPSMODE0 to GPSMODE12” on page 9. P24/GPSMODE8/MOSI Internal pull-up resistor, can be left open if the GPSMODE feature is not used or configured as output by user application. Refer to GPSMODE definitions in section “Setting GPSMODE0 to GPSMODE12” on page 9. P25/NAADET0/MISO Internal pull-down resistor, leave open if Antenna Supervision functionality is unused. Can be left open if configured as output by user application. P26/GPSMODE10/NSS/ NPCS0 Internal pull-up resistor, can be left open if the GPSMODE feature is not used or configured as output by user application. Refer to GPSMODE definitions in section “Setting GPSMODE0 to GPSMODE12” on page 9. P27/GPSMODE11/NPCS1 Internal pull-up resistor, can be left open if the GPSMODE feature is not used or configured as output by user application. Refer to GPSMODE definitions in section “Setting GPSMODE0 to GPSMODE12” on page 9. P29/GPSMODE12/NPCS3 Internal pull-up resistor, can be left open if the GPSMODE feature is not used or configured as output by user application. Refer to GPSMODE definitions in section “Setting GPSMODE0 to GPSMODE12” on page 9. P30/AGCOUT0 Internal pull-down resistor, leave open. P31/RXD1 Internal pull-up resistor, leave open if serial interface is not used. 15 4925A–GPS–02/06 3.4.1 Connecting an Optional Serial EEPROM The ATR0625 offers the possibility to connect an external serial EEPROM. The internal ROM firmware supports to store the configuration of the ATR0625 in serial EEPROM. The pin P16/NEEPROM signals the firmware that a serial EEPROM is connected with the ATR0625. The 32-bit RISC processor of the ATR0625 accesses the external memory with SPI (Serial Peripheral Interface). Atmel recommend to use 32 Kbit 1.8V serial EEPROM, e.g. the Atmel AT25320AY1-1.8. Figure 3-3 shows an example of the serial EEPROM connection. Figure 3-3. Example of a Serial EEPROM Connection AT25320AY1-1.8 ATR0625 P23/SCK P24/MOSI P25/MISO/NAADET0 P29/NPCS3 SCK SI SO CS_N HOLD_N WP_N GND NC P16/NEEPROM P1/GPSMODE0 GND GND NSHDN LDO_EN LDO_OUT VDD18 VDDIO +3V (see Power Supply) LDO_IN LDOBAT_IN NC: Not connected Note: 16 The GPSMODE pin configuration feature can be disabled, because the configuration can be stored in the serial EEPROM. VDDIO is the supply voltage for the pins: P23, P24, P25 and P29. ATR0625 [Preliminary] 4925A–GPS–02/06 ATR0625 [Preliminary] 4. Power Supply The baseband IC is supplied with four distinct supply voltages: • VDD18, the nominal 1.8V supply voltage for the core, the RF-I/O pins, the memory interface and the test pins and all GPIO-pins not mentioned in next item. • VDDIO, the variable supply voltage within 1.8V to 3.6V for following GPIO-pins: P1, P2, P8, P12, P14, P16, P17, P18, P19, P20, P21, P23, P24, P25, P26, P27 and P29 In input mode, these pins are 5V input tolerant. • VDD_USB, the power supply of the USB pins: USB_DM and USB_DP. • VBAT18 to supply the backup domain: RTC, backup SRAM and the pins NSLEEP, NSHDN, LDO_EN, VBAT18, P9/EXTIN0, P13/EXTINT1, P22/RXD2 and P31/RXD1 and the 32kHz oscillator. In input mode, the four GPIO-pins are 5V input tolerant. Figure 4-1, Figure 4-2, and Figure 4-3 show examples of the wiring of ATR0625 power supply. Figure 4-1. External Wiring Example Using Internal LDOs and Backup Power Supply ATR0625 internal 2.3V to 3.6V LDO_IN NSHDN LDO_EN LDO_OUT LDO18 ldoin ldoen ldoout VDD18 Core VDDIO 1.8V to 3.3V variable IO Domain 1 µF (X7R) ldobat_in LDOBAT LDOBAT_IN 1.5V to 3.6V VBAT VBAT18 vbat vbat18 vdd 1 µF (X7R) RTC Backup Memory 0 to 2V or 3V to 3.6V VDDUSB USB SM and Transceiver 17 4925A–GPS–02/06 The baseband IC contains a built in low dropout voltage regulator LDO18. This regulator can be used if the host system does not provide the core voltage VDD18 of 1.8V nominal. In such case, LDO18 will provide a 1.8V supply voltage from any input voltage VDD between 2.3V and 3.6V. The LDO_EN input can be used to shut down VDD18 if the system is in standby mode. If the host system does however supply a 1.8V core voltage directly, this voltage has to be connected to the VDD18 supply pins of the baseband IC. LDO_EN must be connected to GND. LDO_IN can be connected to GND. LDO_OUT must not be connected. A second built in low dropout voltage regulator LDOBAT provides the supply voltage for the RTC and backup SRAM from any input voltage LDOBAT_IN between 2.3V and 3.6V or from VBAT between 1.5V and 3.6V. The backup battery connected to VBAT is only discharged if the supply connected to LDOBAT_IN is shut-down. Only after VDD18 has been supplied to ATR0625 the RTC section will be initialized properly. If only VBAT is applied first, the current consumption of the RTC and backup SRAM is undetermined. Figure 4-2. External Wiring Example Using 1.8V from Host System and Backup Power Supply ATR0625 internal LDO_IN LDO_EN LDO_OUT LDO18 ldoin ldoen ldoout 1.65V to 1.95V 1 µF (X7R) VDD18 Core VDDIO 1.8V to 3.3V variable IO Domain 2.3V to 3.6V ldobat_in LDOBAT LDOBAT_IN 1.5V to 3.6V VBAT VBAT18 vbat vbat18 vdd 1 µF (X7R) RTC Backup Memory 0 to 2V or 3V to 3.6V 18 VDDUSB USB SM and Transceiver ATR0625 [Preliminary] 4925A–GPS–02/06 ATR0625 [Preliminary] The USB Transceiver is disabled if VDD_USB < 2.0V. In this case the pins USB_DM and USB_DP are connected to GND (internal pull-down resistors). The USB Transceiver is enabled if VDD_USB within 3.0V and 3.6V. Figure 4-3. External Wiring Example Using Internal LDOs, USB Supply Voltage and Backup Power Supply ATR0625 internal LDO_IN NSHDN LDO_EN LDO_OUT LDO18 ldoin ldoen ldoout VDD18 Core VDDIO 1.8V to 3.3V variable IO Domain 1 µF (X7R) ldobat_in LDOBAT LDOBAT_IN 1.5V to 3.6V VBAT VBAT18 vbat vbat18 vdd 1 µF (X7R) RTC Backup Memory USB-VSB 5V External LDO 3.3V VDDUSB USB SM and Transceiver 19 4925A–GPS–02/06 5. Oscillator Figure 5-1. Crystal Connection ATR0625 internal XT_IN 32 kHz Crystal Oscillator 32.768 kHz 50 ppm 32.768 kHz clock RTC XT_OUT max. 25 pF max. 25 pF 6. Absolute Maximum Ratings Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Parameters Pin Symbol Min. Max. Unit Operating Free Air Temperature Range –40 +85 °C Storage Temperature –60 +150 °C DC Supply Voltage VDD18 –0.3 +1.95 V DC Supply Voltage VDDIO –0.3 +3.6 V DC Supply Voltage VDD_USB –0.3 +3.6 V DC Supply Voltage LDO_IN –0.3 +3.6 V DC Supply Voltage LDOBAT_IN –0.3 +3.6 V DC Supply Voltage VBAT –0.3 +3.6 V DC Input Voltage P0, P15, P30, SIGHI, SIGLO, CLK23, XT_IN, TMS, TCK, TDI, NTRST, DBG_EN, LDO_EN, NRESET –0.3 +1.95 V DC Input Voltage USB_DM, USB_DP –0.3 +3.6 V +5.0 V P1, P2, P8, P9, P12 to P14, DC Input Voltage –0.3 P16 to P27, P29, P31 Note: Minimum/maximum limits are at +25°C ambient temperature, unless otherwise specified 20 ATR0625 [Preliminary] 4925A–GPS–02/06 ATR0625 [Preliminary] 7. Electrical Characteristics If no additional information is given in column Test Conditions, the values apply to a temperature range from –40°C to +85°C. No. Parameters 1.1 Pin Symbol Min. Typ. Max. Unit DC Supply Voltage Core VDD18 VDD18 1.65 1.8 1.95 V 1.2 DC Supply Voltage VDDIO Domain(1) VDDIO VDDIO 1.65 1.8/3.3 3.6 V 1.3 DC Supply Voltage USB(2) VDD_USB VDDUSB 3.0 3.3 3.6 V 1.4 DC Supply Voltage Backup Domain(3) VBAT18 VBAT18 1.65 1.8 3.6 V 1.5 DC Output Voltage VDD18 VO,18 0 VDD18 V 1.6 DC Output Voltage VDDIO VO,IO 0 VDDIO V 1.7 Low-level Input Voltage VDD18 Domain VDD18 = 1.65V to 1.95V VIL,18 –0.3 0.3 × VDD18 V 1.8 High-level Input Voltage VDD18 Domain VDD18 = 1.65V to 1.95V VIH,18 0.7 × VDD18 VDD18 + 0.3 V 1.9 Low-level Input Voltage VDDIO Domain VDDIO = 1.65V to 3.6V VIL,IO –0.3 +0.41 V 1.10 High-level Input Voltage VDDIO Domain VDDIO = 1.65V to 3.6V VIH,IO 1.46 5.0 V 1.11 Low-level Input Voltage VBAT18 Domain VBAT18 = 1.65V to 1.95V P9, P13, P22, P31 VIL,BAT –0.3 +0.41 V 1.12 High-level Input Voltage VBAT18 Domain VBAT18 = 1.65V to 1.95V P9, P13, P22, P31 VIH,BAT 1.46 5.0 V 1.13 Low-level Input Voltage USB VDD_USB = 3.0V to 3.6V DP, DM VIL,USB –0.3 +0.8 V 1.14 High-level Input Voltage USB VDD_USB = 3.0V to 3.6V DP, DM VIH,USB 2.0 4.6 V 0.4 V Low-level Output Voltage 1.15 VDD18 Domain Test Conditions IOL = 1.5 mA, VDD18 = 1.65V VOL,18 1.16 High-level Output Voltage VDD18 Domain IOH = –1.5 mA, VDD18 = 1.65V VOH,18 1.17 Low-level Output Voltage VDDIO Domain IOL = 1.5 mA, VDDIO = 3.0V VOL,IO 1.18 High-level Output Voltage VDDIO Domain IOH = –1.5 mA, VDDIO = 3.0V VOH,IO 1.19 Low-level Output Voltage VBAT18 Domain IOL = 1 mA P9, P13, P22, P31 VOL,BAT 1.20 High-level Output Voltage VBAT18 Domain IOH = –1 mA P9, P13, P22, P31 VOH,BAT 1.21 Low-level Output Voltage USB IOL = 1.5 mA, VDD_USB = 3.0V to 3.6V, 27Ω external series resistor DP, DM VOL,USB 1.22 High-level Output Voltage USB IOH = –1.5 mA, VDD_USB = 3.0V to 3.6V, 27Ω external series resistor DP, DM VOH,USB Notes: VDD18 – 0.45 V 0.4 VDDIO – 0.5 V 0.4 1.2 V V 0.4 2.7 V V V 1. VDDIO is the supply voltage for the following GPIO pins: P1, P2, P8, P12, P14, P16, P17, P18, P19, P20, P21, P23, P24, P25, P26, P27 and P29 2. Values defined for operating the USB interface. Otherwise VDD_USB may be connected to ground 3. Supply voltage VBAT18 for backup domain is generated internally by the LDOBAT 21 4925A–GPS–02/06 7. Electrical Characteristics (Continued) If no additional information is given in column Test Conditions, the values apply to a temperature range from –40°C to +85°C. No. Parameters Test Conditions 1.23 Input-leakage Current (standard Inputs and I/Os) VDD18 = 1.95V VIL = 0V Pin 1.24 Input Capacitance Symbol Min. ILEAK –1 Typ. ICAP Max. Unit +1 µA 10 pF 1.25 Input Pull-up Resistor NRESET RPU 0.7 1.6 kΩ 1.26 Input Pull-up Resistor TCK, TDI, TMS RPU 10 30 kΩ 1.27 Input Pull-up Resistor P9, P13, P22, P31 RPU 100 220 kΩ 1.28 Input Pull-down Resistor DBG_EN, NTRST, RPD 10 30 kΩ 1.29 Input Pull-down Resistor RF_ON, P0, P15, P30 RPD 100 220 kΩ Configurable Input Pull-up 1.30 Resistor P1, P2, P8, P12, P14, P[16-21], P[23-27], P29 RCPU 62 330 kΩ Configurable Input Pull-down 1.31 Resistor P1, P2, P8, P12, P14, P[16-21], P[23-27], P29 RCPD 45 160 kΩ 1.32 Configurable Input Pull-up Resistor (Idle state) USB_DP RCPU 0.9 1.575 kΩ 1.33 Configurable Input Pull-up Resistor (Operation state) USB_DP RCPU 1.425 3.09 kΩ USB_DP USB_DM RPD 10 500 kΩ 1.34 Input Pull-down Resistor Notes: 1. VDDIO is the supply voltage for the following GPIO pins: P1, P2, P8, P12, P14, P16, P17, P18, P19, P20, P21, P23, P24, P25, P26, P27 and P29 2. Values defined for operating the USB interface. Otherwise VDD_USB may be connected to ground 3. Supply voltage VBAT18 for backup domain is generated internally by the LDOBAT 22 ATR0625 [Preliminary] 4925A–GPS–02/06 ATR0625 [Preliminary] 8. Power Consumption Mode Conditions Typ. Unit (1) Sleep At 1.8V, no CLK23 0.065 Shutdown RTC, backup SRAM and LDOBAT 0.007(1) Normal Note: Satellite acquisition 25 Normal tracking on 6 channels with 1 fix/s; each additional active tracking channel adds 0.5 mA 14 All channels disabled 11 mA 1. Specified value only 9. ESD Sensitivity The ATR0625 is an ESD sensitive device. The current ESD values are to be defined. Observe precautions for handling 10. LDO18 The LDO18 is a built in low dropout voltage regulator which can be used if the host system does not provide the core voltage VDD18. Table 10-1. Electrical Characteristics of LDO18 Parameter Conditions Min. Supply voltage LDO_IN 2.3 Output Voltage (LDO_OUT) 1.65 Typ. 1.8 Output Current (LDO_OUT) Current consumption After startup, no load, at room temperature Current consumption Standby Mode (LDO_EN = 0), at room temperature 1 Max. Unit 3.6 V 1.95 V 80 mA 80 µA 5 µA 23 4925A–GPS–02/06 11. LDOBAT and Backup Domain The LDOBAT is a built in low dropout voltage regulator which provides the supply voltage VBAT18 for the RTC, backup SRAM, P9, P13, P22, P31, NSLEEP and NSHDN. The LDOBAT voltage regulator switches in battery mode if LDOBAT_IN falls below 1.5V. Table 11-1. Electrical Characteristics of LDOBAT Parameter Conditions Supply voltage LDOBAT_IN Typ. 2.3 Supply voltage VBAT 1.5 Output Voltage (VBAT18) If switch connects to LDOBAT_IN. 1.65 Output Current (VBAT18) 1.8 Max. Unit 3.6 V 3.6 V 1.95 V 1.5 mA Current consumption LDOBAT_IN(1) After startup (sleep/backup mode), at room temperature 15 µA Current consumption VBAT(1) After startup (backup mode and LDOBAT_IN = 0V), at room temperature 10 µA Current consumption After startup (normal mode), at room temperature 1.5 mA Note: 24 Min. 1. If no current is caused by outputs (pad output current as well as current across internal pull-up resistors) ATR0625 [Preliminary] 4925A–GPS–02/06 ATR0625 [Preliminary] 12. Ordering Information Extended Type Number Package MPQ Remarks ATR0625-PYQW QFN56 2000 8 mm × 8 mm, 0.50 mm pitch, Pb-free, RoHS-compliant, green ATR0625-EK1 - 1 Evaluation kit/Road test kit ATR0625-DK1 - 1 Development kit inclusive example design information 13. Package QFN56 Package: QFN56 8 x 8 Exposed pad 6.5 x 6.5 Dimensions in mm Not indicated tolerances ±0.05 8 0.9 max. +0 6.5 0.05-0.05 43 56 1 56 1 42 Pin 1 ID technical drawings according to DIN specifications 29 14 28 0.4±0.1 0.25 14 15 0.5 nom. Drawing-No.: 6.543-5121.01-4 Issue: 1; 02.09.05 25 4925A–GPS–02/06 Atmel Corporation 2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Regional Headquarters Europe Atmel Sarl Route des Arsenaux 41 Case Postale 80 CH-1705 Fribourg Switzerland Tel: (41) 26-426-5555 Fax: (41) 26-426-5500 Asia Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimshatsui East Kowloon Hong Kong Tel: (852) 2721-9778 Fax: (852) 2722-1369 Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 Atmel Operations Memory 2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 RF/Automotive Theresienstrasse 2 Postfach 3535 74025 Heilbronn, Germany Tel: (49) 71-31-67-0 Fax: (49) 71-31-67-2340 Microcontrollers 2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 La Chantrerie BP 70602 44306 Nantes Cedex 3, France Tel: (33) 2-40-18-18-18 Fax: (33) 2-40-18-19-60 ASIC/ASSP/Smart Cards 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Biometrics/Imaging/Hi-Rel MPU/ High Speed Converters/RF Datacom Avenue de Rochepleine BP 123 38521 Saint-Egreve Cedex, France Tel: (33) 4-76-58-30-00 Fax: (33) 4-76-58-34-80 Zone Industrielle 13106 Rousset Cedex, France Tel: (33) 4-42-53-60-00 Fax: (33) 4-42-53-60-01 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Scottish Enterprise Technology Park Maxwell Building East Kilbride G75 0QR, Scotland Tel: (44) 1355-803-000 Fax: (44) 1355-242-743 Literature Requests www.atmel.com/literature Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. © Atmel Corporation 2006. All rights reserved. Atmel ®, logo and combinations thereof, Everywhere You Are ® and others, are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. ARM ®, logo and others are the registered trademarks or trademarks of ARM Ltd. Other terms and product names may be trademarks of others. Printed on recycled paper. 4925A–GPS–02/06