AZ833P MICROMINIATURE POLARIZED LATCHING RELAY FEATURES • Single and dual coil latching versions • High dielectric and surge voltage: 2.5 KV surge (per Bellcore TA–NWT–001089) 1.5 KV surge (per FCC Part 68) 1,000 Vrms, open contacts • Low power consumption: 79 mW pickup • Stable contact resistance for low level signal switching • Epoxy sealed • UL, CUR file E43203 • All plastics meet UL94 V–O, 30 min. oxygen index GENERAL DATA CONTACTS Life Expectancy Mechanical Electrical Minimum operations 1 x 108 1 x 105 at 0.5 A, 125 VAC, resistive 2 x 105 at 1.0 A, 30 VDC, resistive Operate Time (set) (typical) 3 ms at nominal coil voltage Release Time (reset) (typical) 3 ms at nominal coil voltage (with no coil suppression) Bounce (typical) At 10 mA contact current 1 ms at operate or release Dielectric Strength (at sea level) See table Insulation Resistance 109 ohms min. at 25°C, 500 VDC, 50% RH Ambient Temperature Operating Storage At nominal coil voltage -40°C (-40°F) to 85°C (185°F) -40°C (-40°F) to 105°C (221°F) 79 mW (dual coil) 39 mW (single coil) Vibration Operational, 35 g, 10–1000 Hz Max. Continuous Dissipation 1.0 W at 20°C (68°F) Shock Operational, 50 g min., 11 ms Non-destructive, 150 g min., 11 ms Temperature Rise At nominal coil voltage 18°C (32°F) Max. Solder Temp. Temp./Time See soldering profile Max. 110°C (230°F) Max. Solvent Temp. 80°C (176°F) Max. Immersion Time 30 seconds Weight 2.5 grams Enclosure P.B.T. polyester Terminals Tinned copper alloy, P.C. Packing unit in pcs THT SMT 50 per plastic tube / 1000 per carton box 400 per reel / 2000 per carton box Arrangement DPDT (2 Form C) Bifurcated crossbar contacts Ratings Resistive load: Max. switched power: 60 W or 62.5 VA Max. switched current: 2.0 A Max. switched voltage: 220 VDC or 250 VAC Rated Load UL/CSA 0.25 A at 240 0.5 A at 125 2.0 A at 30 0.3 A at 110 VAC VAC VDC VDC Material Silver nickel gold plated Silver palladium available upon request COIL (Polarized) Power At Pickup Voltage (typical) Temperature NOTES 1. All values at 20°C (68°F). 2. Relay may pull in with less than “Must Operate” value. 3. Relay has fixed coil polarity. 4. Specifications subject to change without notice. ZETTLER electronics GmbH Junkersstrasse 3, D-82178 Puchheim, Germany Tel. +49 89 800 97 0 Fax +49 89 800 97 200 [email protected] www.ZETTLERelectronics.com 2005-08-04 AZ833P RELAY ORDERING DATA COIL SPECIFICATIONS STANDARD RELAYS: Bistable, 2 coils Nominal Coil VDC 3 Set / Reset VDC 2.25 4.5 5 6 9 Order Number Max. Continuous VDC 6.5 Coil Resistance Ohm ± 10% 64.3 THT Through Hole AZ833P2–3DE SMT Long AZ833P2S1–3DE SMT Short AZ833P2S2–3DE 3.38 9.8 145 AZ833P2–4.5DE AZ833P2S1–4.5DE AZ833P2S2–4.5DE 3.75 10.9 178 AZ833P2–5DE AZ833P2S1–5DE AZ833P2S2–5DE 4.50 6.75 13.0 19.6 257 578 AZ833P2–6DE AZ833P2–9DE AZ833P2–6DE AZ833P2S1–9DE AZ833P2S2–6DE AZ833P2S2–9DE 12 9.00 26.2 1,029 AZ833P2–12DE AZ833P2S1–12DE AZ833P2S2–12DE 24 18.00 52.3 4,114 AZ833P2–24DE AZ833P2S1–24DE AZ833P2S2–24DE STANDARD RELAYS: Bistable, 1 coil Order Number Nominal Coil VDC 3 Set / Reset VDC 2.25 Max. Continuous VDC 6.5 Coil Resistance Ohm ± 10% 128 THT Through Hole AZ833P1–3DE SMT Long AZ833P1S1–3DE SMT Short AZ833P1S2–3DE 4.5 3.38 9.8 289 AZ833P1–4.5DE AZ833P1S1–4.5DE AZ833P1S2–4.5DE 5 3.75 10.9 357 AZ833P1–5DE AZ833P1S1–5DE AZ833P1S2–5DE 6 9 4.50 6.75 13.0 19.6 514 1,157 AZ833P1–6DE AZ833P1P1–9DE AZ833P1S1–6DE AZ833P1S1–9DE AZ833P1S2–6DE AZ833P1S2–9DE 12 9.00 26.2 2,057 AZ833P1–12DE AZ833P1S1–12DE AZ833P1S2–12DE 24 18.00 52.3 8,228 AZ833P1–24DE AZ833P1S1–24DE AZ833P1S2–24DE INITIAL DIELECTRIC STRENGTH (minimum) VRMS, 1 min. SURGE Peak (V) Rise Time (µS) Decay Time* (9µS) (1/2 peak) Between open contacts 1,000 1,500 10 160 Between contact sets 1,000 1,500 2 160 Between coil and contacts 1,800 2,500 2 10 * Decay time measured from beginning of surge. LOAD LIMIT CURVE RECOMMENDED SOLDERING PROFILE Convection Soldering V ZETTLER electronics GmbH Junkersstrasse 3, D-82178 Puchheim, Germany Tel. +49 89 800 97 0 Fax +49 89 800 97 200 [email protected] www.ZETTLERelectronics.com 2005-08-04 AZ833P MECHANICAL DATA THT SMT Long Terminals SMT Short Terminals PCB Layout Solder Pad Layout Viewed toward terminals Viewed toward the component side of the PCB Long terminals Short terminals Wiring Diagram Viewed toward terminals + SET – – + + RESET SET + – RESET – Shown in reset position Shown in reset position Viewed toward component side of PCB – SET + + + RESET SET – – – RESET + Shown in reset position Shown in reset position All dimensions in mm ZETTLER electronics GmbH Junkersstrasse 3, D-82178 Puchheim, Germany Tel. +49 89 800 97 0 Fax +49 89 800 97 200 [email protected] www.ZETTLERelectronics.com 2005-08-04 AZ833P PACKAGING Tape and reel for SMT version with long terminals – AZ833P1S1 or AZ833P2S1 Tape and reel for SMT version with short terminals – AZ833P1S2 or AZ833P2S2 Tube for THT version – AZ833P1 or AZ833P2 All dimensions in mm ZETTLER electronics GmbH Junkersstrasse 3, D-82178 Puchheim, Germany Tel. +49 89 800 97 0 Fax +49 89 800 97 200 [email protected] www.ZETTLERelectronics.com 2005-08-04