EPCOS B41161A3337M000

Aluminum electrolytic capacitors
SMD capacitors
Series/Type:
B41161
Date:
May 2009
© EPCOS AG 2009. Reproduction, publication and dissemination of this publication, enclosures hereto and the
information contained therein without EPCOS' prior express consent is prohibited.
SMD capacitors
B41161
Standard series 125 °C
General-purpose grade capacitors
Applications
General-purpose applications in the entertainment industry
Features
RoHS-compatible
Load life of 1000 h at 125 °C
Suitable for reflow soldering, see chapter "SMD capacitors Mounting instructions"
Construction
Surface mounting device
Minus pole marking on the case
Delivery mode
Taped and reeled
Refer to chapter "SMD capacitors - Taping and packing" for
further details.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 2 of 11
B41161
Standard series 125 °C
Specifications and characteristics in brief
Rated voltage VR
Operating temperature range
Rated capacitance CR
(20 °C, 120 Hz)
Capacitance tolerance
Load life
(125 °C, VR)
Leakage current Ileak
(20 °C, after 2 minutes)
Low temperature stability
(impedance ratio)
(120 Hz)
Shelf life
(125 °C)
Frequency multiplier
for rated ripple current
10 ... 50 V DC
40 °C ... +125 °C
10 ... 330 µF
±20% M
1000 h
VR (V DC)
Requirements:
∆C/C
≤ ±30% of initial value
tan δ
≤ 3 times initial specified value
Ileak
≤ initial specified limit
10
8
16
8
25
4
35
3
50
3
14
12
10
8
8
500 h
Requirements:
∆C/C
≤ ±20% of initial value
tan δ
≤ 2 times initial specified value
Ileak
≤ initial specified limit
After test: VR to be applied for 30 minutes, 24 to 48 hours before
measurement.
50 Hz 120 Hz 300 Hz 1 kHz
≥10 kHz
0.35
0.50
0.64
0.83
1.00
Please read Cautions and warnings and
Important notes at the end of this document.
Page 3 of 11
B41161
Standard series 125 °C
Dimensional drawings
d x l (mm)
8 × 10 ... 10 × 10:
➀
➁
➂
➃
Case
Terminal base board
Minus pole
Plus pole
Case dimensions
d × l (mm)
A
B
C
E
L
H
8 × 10
10 × 10
2.9
8.3
8.3
3.1
10
3.2
10.3
10.3
4.5
10
0.8 ... 1.1
Layout recommendation
Please read Cautions and warnings and
Important notes at the end of this document.
d × l (mm)
X
Y
a
8.0 × 10.0
2.5
3.5
3.0
10.0 × 10.0
2.5
4.0
4.0
Page 4 of 11
B41161
Standard series 125 °C
Overview of available types
VR (V DC)
10
16
25
35
50
Case dimensions d × l (mm)
CR (µF)
8 × 10
33
8 × 10
47
8 × 10
100
220
8 × 10
330
10 × 10
8 × 10
10 × 10
10 × 10
10 × 10
Other voltage and capacitance ratings are available upon request.
Technical data and ordering codes
VR
V DC
10
16
25
35
50
CR
120 Hz
20 °C
µF
220
330
100
220
100
47
100
33
47
Case
dimensions
d×l
mm
8 × 10
10 × 10
8 × 10
10 × 10
8 × 10
8 × 10
10 × 10
8 × 10
10 × 10
Please read Cautions and warnings and
Important notes at the end of this document.
tan δmax
120 Hz
20 °C
0.32
0.32
0.24
0.24
0.21
0.18
0.18
0.18
0.18
IAC,R
100 kHz
125 °C
mA
93
118
89
113
84
79
101
74
94
Page 5 of 11
Ordering code
B41161A3227M000
B41161A3337M000
B41161A4107M000
B41161A4227M000
B41161A5107M000
B41161A7476M000
B41161A7107M000
B41161A6336M000
B41161A6476M000
B41161
Standard series 125 °C
Mounting instructions
Soldering
Recommended conditions
For reflow, use thermal conduction systems such as infrared radiation (IR) or hot blast. Vapor
heat transfer systems (VPS) are not recommended.
Observe proper soldering conditions (temperature, time, etc.).
Do not exceed the specified limits.
Temperature measuring method: Measure temperature in assuming quantitative production, by
sticking the thermo-couple to the capacitor upper part with epoxy adhesives.
Consult us for additional reflow restrictions.
Lead-free reflow
d (mm)
4 ... 6.3
8 ... 10
Peak temperature
250 °C
235 °C
Time in peak temperature
5s
5s
Time in 200 °C or more
60 s
60 s
Time of reflow
1 time
1 time
Please read Cautions and warnings and
Important notes at the end of this document.
Page 6 of 11
B41161
Standard series 125 °C
Taping and packing
Taping of SMD capacitors
Case dimensions
d × l (mm)
W
P
F
A0
B0
T2
4 × 5.4
4 × 5.8
5 × 5.4
5 × 5.8
12.0
8.0
5.5
5.0
5.0
5.8
12.0
8.0
5.5
5.0
5.0
6.3
12.0
12.0
5.5
6.0
6.0
5.8
12.0
12.0
5.5
6.0
6.0
6.3
Case dimensions
d × l (mm)
W
P
F
A0
B0
T2
6.3 × 5.8
6.3 × 7.7
8 × 6.2
8 × 10
16.0
12.0
7.5
7.0
7.0
6.3
16.0
12.0
7.5
7.0
7.0
8.2
16.0
12.0
7.5
8.7
8.7
6.8
24.0
16.0
11.5
8.7
8.7
11.0
Please read Cautions and warnings and
Important notes at the end of this document.
Page 7 of 11
6.3 × 5.4
16.0
12.0
7.5
7.0
7.0
5.8
10 × 10
24.0
16.0
11.5
10.7
10.7
11.0
B41161
Standard series 125 °C
Reel packing
Capacitor dimensions
d × l (mm)
Quantity per reel
pcs.
4×l
2000 pcs.
5 × l, 6.3 × l, 8 × 6.2
1000 pcs.
8 × 10, 10 × l
500 pcs.
d × l (mm)
4 × l, 5 × l
6.3 × l, 8 × 6.2
8 × 10, 10 × l
A
14
18
26
Please read Cautions and warnings and
Important notes at the end of this document.
Page 8 of 11
B41161
Standard series 125 °C
Cautions and warnings
General
1
Aluminum electrolytic capacitors have a bi-polar structure. This is marked on the body of the
capacitor. A capacitor must not be mounted with reversed polarity. The application of an AC
or reverse voltage may cause a short circuit or damage the capacitor. Bi-polar capacitors
must not be used in AC applications, where the polarity may be reversed in the circuits or is
unknown.
2
The DC voltage applied to the capacitor terminal must not exceed its rated operating voltage,
as this will result in a rapid increase of the leakage current and may damage the capacitor. It
is recommended to operate the capacitor at 70 – 80% of its rated voltage to optimize its
service life.
3
The ripple current applied to the capacitor must be within the permitted range. An excessive
ripple current leads to impaired electrical properties and may damage the capacitor. Note
that the sum of the peak values of the ripple voltage and the DC operating voltage must not
exceed the rated DC voltage.
4
Capacitors must be used within their permitted range of operating temperature. Operation at
room temperature optimizes their service life.
5
Capacitors with case diameter ≥8 mm are equipped with a safety vent. In capacitors fitted
with a lead or soldering lug, the safety vent is usually located at the base of the case. It
needs sufficient space around it to operate optimally. The following dimensions are
recommended: for case diameter d = 8 to 16 mm, more than 2 mm; for d = 18 to 35 mm,
more than 3 mm; and for d = 42 mm or more, more than 5 mm.
6
Capacitors should not be mounted with the safety vent face down on the board. Do not
locate any wire or copper trace near the safety vent. Do not reverse the voltage, as this may
result in excess pressure and the leakage of electrolyte.
7
Gas is released through the safety vent when the pressure inside the capacitor is too high. A
gaseous liquid around the safety vent does not indicate a leakage of electrolyte.
8
The capacitor should be stored under conditions of normal temperature and in a non-acid,
non-alkali environment of normal humidity. Exposure to high temperatures, for example
under direct sunlight, will reduce its operating life. If the capacitor is stored in an environment
containing acids or alkalis, the solderability of the leads may be affected.
9
containing acids or alkalis, the solderability of the leads may be affected.The leakage current
of an aluminum electrolytic capacitor may increase after a long period of storage. After such
storage, the capacitor must be aged by applying the rated operating voltage for 6 – 8 hours
before use.
10
Manual soldering:
a Soldering must be performed within the specified conditions.
Bit temperature: 350 °C; application time of soldering iron: 3 seconds.
b Ensure that the soldering iron does not touch any part of the capacitor body.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 9 of 11
B41161
Standard series 125 °C
11
Do not apply excessive force to the leads and terminals. Do not move the capacitor after
soldering it onto the PC board and do not carry the PC board by gripping the capacitor.
Observe the following rules to prevent undue stress to the capacitor:
a Do not tilt or bend the capacitor after soldering.
b Ensure that the terminal spacing matches the corresponding hole spacing on the PC board.
12
The aluminum case is not insulated from the cathode. Do not place a conductor under the
aluminum capacitors on the PC board as this may cause a short circuit. The case and top of
capacitors used in switched mode power supplies have a high-voltage-resistant heat shrink
sleeve to ensure safe usage.
13
The leads of capacitors with a case diameter exceeding 14 mm cannot be used for fixing.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 10 of 11
Important notes
The following applies to all products named in this publication:
1. Some parts of this publication contain statements about the suitability of our products for
certain areas of application. These statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned. We
nevertheless expressly point out that such statements cannot be regarded as binding
statements about the suitability of our products for a particular customer application.
As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar
with them than the customers themselves. For these reasons, it is always ultimately incumbent on the customer to check and decide whether an EPCOS product with the properties described in the product specification is suitable for use in a particular customer application.
2. We also point out that in individual cases, a malfunction of electronic components or
failure before the end of their usual service life cannot be completely ruled out in the
current state of the art, even if they are operated as specified. In customer applications
requiring a very high level of operational safety and especially in customer applications in
which the malfunction or failure of an electronic component could endanger human life or
health (e.g. in accident prevention or lifesaving systems), it must therefore be ensured by
means of suitable design of the customer application or other action taken by the customer
(e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by
third parties in the event of malfunction or failure of an electronic component.
3. The warnings, cautions and product-specific notes must be observed.
4. In order to satisfy certain technical requirements, some of the products described in this
publication may contain substances subject to restrictions in certain jurisdictions (e.g.
because they are classed as hazardous). Useful information on this will be found in our Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more detailed questions, please contact our sales offices.
5. We constantly strive to improve our products. Consequently, the products described in this
publication may change from time to time. The same is true of the corresponding product
specifications. Please check therefore to what extent product descriptions and specifications
contained in this publication are still applicable before or when you place an order. We also
reserve the right to discontinue production and delivery of products. Consequently, we
cannot guarantee that all products named in this publication will always be available. The
aforementioned does not apply in the case of individual agreements deviating from the foregoing for customer-specific products.
6. Unless otherwise agreed in individual contracts, all orders are subject to the current version of the "General Terms of Delivery for Products and Services in the Electrical Industry" published by the German Electrical and Electronics Industry Association
(ZVEI).
7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CSMP, CSSP, CTVS, DSSP,
MiniBlue, MKK, MLSC, MotorCap, PCC, PhaseCap, PhaseCube, PhaseMod, SIFERRIT,
SIFI, SIKOREL, SilverCap, SIMDAD, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse,
WindCap are trademarks registered or pending in Europe and in other countries. Further
information will be found on the Internet at www.epcos.com/trademarks.
Page 11 of 11