Analog 5-wire PET-On-Glass Touch Screen Specification 1. Mechanical Dimensions and Construction 1.1 General: Analog Resistive touch screen is laminated by ITO PET to ITO glass. 1.2 Construction: Item 1 2 3 4 5 6 7 8 9 10 11 12 Description ITO PET (Top layer) New designed printing ITO Patterned Glass (Bottom layer) New designed printing Tail Base Tail cover lay Connector Top layer circuit Bottom layer circuit Layer to layer contacted Dot spacer Isolation Layer Glue Preserve pet Material Remarks 0.188mm ITO PET Antiglare coating Film Surface hardness: 3H Resistance:300~600Ω/□ 2.8 mm ITO Glass Resistance:300~900Ω/□ Kapton Separated Tail Kapton AMP compatible 2,54mm Silver ink Silver ink Silver ink UV Cure ink Isolation Adhesive UV Glue PET Film Touch screen side view: Changes that contribute to technical improvement are subject to alternations 2006 Bearb. Gepr. Vert. Datum 18.08. 18.08 Name Maurer Maurer TOUCHSCREEN 17,15", 5-Wire EDV-Datasheet AMT-02512-01 SPECIFICATIONS OF ANALOG RESISTIVE PET-ON-GLASS TOUCH SCREEN don’t change manually Manufactured by Apex Material Technology Corp. H Zu Änd. Datum Name D 79346 Endingen 1070.0476 page 1 of 4 Index: - 1.3 Input Method and Activation Force Input Method 16mm dia. Silicon "finger" Average Activation Force Less than 1.00 N 2. Typical Optical Characteristics 2.1 2.2 Visible Light Transmission: Haze: > 80% < 13% 3. Electrical Specifications 3.1 3.2 3.3 3.4 3.5 3.6 Operating Voltage: Contact current: Circuit close resistance: Circuit open resistance: Contact bounce: Linearity Specifications: 5.5V or less 20mA (maximum) 20~300Ω > 10MΩ at 25VDC < 15ms The linearity specifications are based on Hampshire or PenMount touch screen controllers and drivers to define. 10 mm inside of X and Y active area dimensions. The area 10 mm inside of X and Y active area dimensions. 3.6.1 Inner Active Area : Perimeter of Active Area : Changes that contribute to technical improvement are subject to alternations 2006 Bearb. Gepr. Vert. Datum 18.08. 18.08 Name Maurer Maurer TOUCHSCREEN 17,15", 5-Wire EDV-Datasheet AMT-02512-01 SPECIFICATIONS OF ANALOG RESISTIVE PET-ON-GLASS TOUCH SCREEN don’t change manually Manufactured by Apex Material Technology Corp. H Zu Änd. Datum Name D 79346 Endingen 1070.0476 page 2 of 4 Index: - 3.6.2 Calculate Linearity % Linearity = ∆X 2 + ∆Y 2 * 100 Active Area Diagonal £ G Y £ G X 3.6.3 Linearity: Inner Active Area : Perimeter of Active Area : <1.0% <1,5% 3.7 Electrostatic Discharge Protection : (per EN 61000-4-2 ) The touch screen withstands of 15KV air discharge and 8KV contact discharge. 4. Environment Specification 4.1 4.2 Operating Temperature Storage Temperature - 10° C ~ + 60° C Humidity less than 90% RH, no dew condensation - 40° C ~ + 80° C, at Ambient Humidity 5. Reliability Test 5.1 Exposure to high temperature Touch panel is put into a test machine at the condition of 80°C for 504 hours. Then it is left at the room temperature for 24 hours or more. The measurement must satisfy the following: - Circuit close resistance: as Sec. 3.3 - Circuit open resistance: as Sec. 3.4 - Contact bounce: as Sec. 3.5 - Linearity test: as Sec. 3.6 5.2 Exposure to low temperature Touch panel is put into a test machine at the condition of –40°C for 504 hours. Then it is left at the room temperature for 24 hours or more. The measurement must satisfy the following: - Circuit close resistance: as Sec. 3.3 - Circuit open resistance: as Sec. 3.4 - Contact bounce: as Sec. 3.5 - Linearity test: as Sec. 3.6 Changes that contribute to technical improvement are subject to alternations 2006 Bearb. Gepr. Vert. Datum 18.08. 18.08 Name Maurer Maurer TOUCHSCREEN 17,15", 5-Wire EDV-Datasheet AMT-02512-01 SPECIFICATIONS OF ANALOG RESISTIVE PET-ON-GLASS TOUCH SCREEN don’t change manually Manufactured by Apex Material Technology Corp. H Zu Änd. Datum Name D 79346 Endingen 1070.0476 page 3 of 4 Index: - 5.3 Exposure to constant temperature and humidity Touch panel is put into a test machine at the condition of 60°C, 90%RH for 504 hours. Then it is left at the room temperature for 24 hours or more. The measurement must satisfy the following: - Circuit close resistance: as Sec. 3.3 - Circuit open resistance: as Sec. 3.4 - Contact bounce: as Sec. 3.5 - Linearity test: as Sec. 3.6 5.4 Thermal Shock Touch panel is put into a test machine at the condition of –40°C for 30 minutes, and then 80°C for 30 minutes. The process is repeated by 10 cycles. Then it is left at the room temperature for 24 hours or more. The measurement must satisfy the following: - Circuit close resistance: as Sec. 3.3 - Circuit open resistance: as Sec. 3.4 - Contact bounce: as Sec. 3.5 - Linearity test: as Sec. 3.6 6. Durability test: 6.1 Finger touches Touch panel is hit 36 millions times with a silicone rubber of R8 finger, hitting rate is by 250g at 2 times per second. The measurement must satisfy the following: - Circuit close resistance: as Sec. 3.3 - Circuit open resistance: as Sec. 3.4 - Contact bounce: as Sec. 3.5 - Linearity test: as Sec. 3.6 7. Optical Performance: 7.1 Optical inspection method and optical defect standards refer to document. A001-2 Touch Screen Optical Quality Standard. 7.2 Outside to Active Area : any optical defected in this area need to be ignored if no effected to touch screen function. 8. Others 8.1 Always store the touch screen in its original shipping container under normal conditions (20~25°C, 65% RH) Changes that contribute to technical improvement are subject to alternations 2006 Bearb. Gepr. Vert. Datum 18.08. 18.08 Name Maurer Maurer TOUCHSCREEN 17,15", 5-Wire EDV-Datasheet AMT-02512-01 SPECIFICATIONS OF ANALOG RESISTIVE PET-ON-GLASS TOUCH SCREEN don’t change manually Manufactured by Apex Material Technology Corp. H Zu Änd. Datum Name D 79346 Endingen 1070.0476 page 4 of 4 Index: -