COMMUNICATIONS MODULES & SUBSYSTEMS TM WaveReady Optical Link Monitoring System: BrightJack 200 Key Features • Enables protocol- and format-independent monitoring of link loss • Enables real-time monitoring of in-service fiber pairs • Requires no power for passive customer-end interface • Supports link budgets up to 20 dB • Provides direct TL-1 interface • Provides monitoring for up to six fiber links from a highdensity 1U CO chassis Applications • Enables optical link monitoring of up to six discrete optical fiber pairs • Enables optical demarcation interface between carrier and client networks Compliance • Telcordia NEBS Level 3 • UL 60950 Third Edition • FCC Class A The JDSU WaveReady™ BrightJack 200 is a compact, modular performance monitoring solution for optical fiber links. The BrightJack lets system operators isolate faults within the fiber plant to improve response time. BrightJack also lets system operators monitor the health of the optical fiber over time and address slow degradation in fiber performance before it can result in unplanned service outages. The BrightJack 200 operates independent of optical power and does not disrupt service in the event of power failure. Unlike Layer 2 performance monitoring solutions, which may not differentiate between equipment failure and fiber failure, the BrightJack monitors the health of the fiber plant from the central office (CO) without dependence on electronics located at the far end of the link. With interfaces for remote TL-1 alarms over transmission control protocol/ Internet protocol (TCP/IP), visual alarms, and local telemetry alarms, the BrightJack is readily integrated into a wide variety of network management interfaces and ready to deploy out of the box. CO Local Loop Fiber BrightJack 200 Shelf 1625 nm monitor wavelength RT BrightJack 200 Loopback Figure 1 Local loop fiber NORTH AMERICA : 800 498-JDSU (5378) WORLDWIDE : +800 5378-JDSU WEBSITE : www.jdsu.com/waveready BRIGHTJACK 200 2 Sample Configurations 10 GigE OC-192 LAN PHY OC-12 1/2 G Fiber Channel WDM Gigabit Ethernet Central Office PC BrightJack 200 Chassis Fiber Plant Remote Loopback Module OC-192 10 GigE LAN PHY OC-12 Gigabit Ethernet WDM 1/2 G Fibre Channel Figure 2 BrightJack 200 application Central Office Customer Premises Dual Link Monitor Tx 1.3 dB max (EOL) with connectors Rx Fiber loss 0 dB min 10 dB max Rx 0.9 dB max (EOL) with connectors Tx Fiber loss 0 dB min 10 dB max 0.9 dB max (EOL) with connectors Figure 3 BrightJack 200 insertion loss Remote Loopback 0.9 dB max (EOL) with connectors Customer Premises BRIGHTJACK 200 3 1 Performance Specifications Parameter Min Typical Max Optical Characteristics Supported data rates Operating wavelength range 1310 nm wavelength 1550 nm wavelength Monitor channel wavelength range Client input power range Monitor input power Link loss range Insertion loss2 End-to-end path from CO Client In to CP Client Out End-to-end path from CP Client In to CO Client Out Return loss Optical input power PDL PMD Any 1260 nm 1480 nm 1620 nm –10 dBm –8 dBm 0 dB 1310 nm 1550 nm 1625 nm — –5 dBm — 1360 nm 1580 nm 1630 nm 0 dBm –1.4 dBm 20 dB — — 40 dB — — — — — — — — — 2.2 dB 1.8 dB — 300 mW 0.2 dB 0.2 ps –40 V DC — — — –48 V DC 225 mA 10.8 W 0W –57.5 V DC 300 mA 15 W — Electrical Characteristics (Chassis) DC supply voltage (CO chassis) 3, 4 DC current (CO chassis) Power dissipation (CO chassis) Power dissipation (Remote loopback) Physical Characteristics (Chassis) External dimensions including brackets (H x W x L) Weight (approximate) 4.5 x 58.4 x 30.5 cm (1.75 x 23.0 x 13.2 in) 3.2 kg (7.0 lb) Physical Characteristics (Remote loopback) External dimensions including brackets (H x W x L) Weight (approximate) 13.0 x 2.74 x 15.2 cm (5.1 x 1.08 x 6.0 in) 0.45 kg (1.0 lb) Environmental Characteristics Normal operating temperature Extended operating temperature Storage temperature Relative humidity (non-condensing) 0°C –5°C –40°C 5% — — — — 40°C 55°C 85°C 85% Interface Specifications Optical connectors DB-9/RS-232 craft user port 1 LC/PC on CO equipment, SC/PC on terminal loopback module Three-wire serial TTL, 9600 Baud, no parity, no flow control, 8 data bits, 1 stop bit TL1 command line via serial (RS-232) or network (10/100Base-T) ports This product should be deployed in accordance with your company’s deployment directives Refer to Figure 2 BrightJack insertion loss The DC power supply must be –48 V SELV output and certified by a nationally recognized test laboratory (NRTL). UL tested at –48 V 4 The Remote Loopback module (BJK-200LB02B) is a passive optical device with no applicable electrical connections or heat dissipation 2 3 BRIGHTJACK 200 Ordering Information For more information on this or other products and their availability, please contact your local JDSU account manager or JDSU directly at 1-800-498-JDSU (5378) in North America, +1 800-5378-JDSU worldwide or via e-mail at [email protected]. Sample: BJK-200BC200 Product Code BJK-200BC200 BJK-200CM100 BJK-200LM63B BJK-200DM42B BJK-200DC48R BJK-200AL100 BJK-200LB02B Description BrightJack 4-slot Chassis, ANSI BrightJack Controller Module 100 BrightJack Laser Source Module, 3 Port BrightJack Dual Link Monitor Module, Low IL BrightJack 48 V DC Power Supply Plug-in BrightJack Alarm Interface Module BrightJack Remote Loopback Module, Low IL NORTH AMERICA : 800 498-JDSU (5378) CLEI WOMA210HRA WOCUAB1AA WOCUAB2JAA WOCUAB0JAA WOPUAAFEAA WOCUAB4JAA WOCUAB3JAA WORLDWIDE : +800 5378-JDSU Product specifications and descriptions in this document subject to change without notice. © 2008 JDS Uniphase Corporation WEBSITE : www.jdsu.com/waveready May 2008 30149398 000 0508 BRIGHTJACK200.DS.CMS.TM.AE