COMMUNICATIONS MODULES & SUBSYSTEMS Metro-Access DWDM Erbium Doped Fiber Amplifer LightAmp Key Features • Protocol and data rate independent – including 10 G/OC-192 applications • Simple to install, "plug-and-play" • Optical output monitor for maintenance • Easily configurable as a booster or pre/inline amplifier • Constant gain and constant power modes • Works with redundant -48 volt supplies • Low power consumption and noise figure • High-speed control circuitry provides transient suppression Applications • Booster or pre/inline amplifier • Access and metro optical networks • DWDM point-to-point applications • DWDM optical add-drop or X-C nodes Compliance • NEBS Level 3 • FDA Class 1M laser device • FCC Class A device • UL 60950 Third Edition The WaveReady™ 3000 series LightAmp metro-access dense wavelength division multiplexing (DWDM) optical amplifier is a configurable, multi-channel device that provides simple and economical C-band optical amplification in a flexible, ready-to-use package. It is network-ready and includes an advanced, efficient pump laser and mid-stage variable attenuator. LightAmp features a switch on the front panel that enables field personnel to install and configure it in seconds as a power, inline, or pre-amplifier. The module works by default in constant gain mode, but can be configured to constant power mode. Its ease-of-use and performance make LightAmp the ideal solution for access and metro DWDM optical networks. Front panel LEDs show the status of the module, while the integrated electronics provide simple alarm and control functionality. An RS-232 interface and Ethernet port, through a WaveReady shelf and communications module, allow for remote management. The package is designed to be deployed in either the WaveReady 3500 or 3100 systems which mount in 19- or 23-inch telecommunications racks. NORTH AMERICA : 800 498-JDSU (5378) WORLDWIDE : +800 5378-JDSU WEBSITE : www.jdsu.com METRO-ACCESS DWDM ERBIUM DOPED FIBER AMPLIFER 2 Reach Extension Customer Premises Equipment DWDM LGX 15 SC Customer Premises Equipment DWDM LightAmp LGX 15 SC Performance Specifications1 Parameter Optical Characteristics (All Models) Operating wavelength range Operating total input power range Output monitor tap ratio Time constant of control circuitry Return loss Booster Characteristics Output power (-9 dBm < Pin < 0 dBm) Polarization sensitivity Noise figure (-9 dBm < Pin < 0 dBm) Pre/Inline Amplifier Characteristics Gain (-29 dBm ≤ Pin ≤-9 dBm) Gain flatness over operating wavelength range Polarization sensitivity Noise figure (-29 dBm ≤ Pin ≤-9 dBm) Electrical Characteristics DC supply voltage Power dissipation Alarm relay signals (major and minor) Physical Dimensions Size (H x W x L) Weight Environmental Characteristics Operating ambient temperature Storage temperature Relative humidity (non-condensing) Minimum Typical Maximum 1530 nm -29 dBm -22 dB -40 dB -45 dB 1562 nm 0 dBm -16 dB 2.5 ms - 13 dBm - 16 dBm 6.75 dB 17 dBm 0.5 dB 8 dB 23 dB - ±1 dB 5 dB ±1.5 dB 0.5 dB 6.5 dB - -48 V 5W Dry contact 8.5 W - - 6.8 x 1.0 x 8.6 inches 1.5 lbs - -5 °C -40 °C 5% - 55 °C 85 °C 85 % Note: This product should be deployed in accordance with your company’s deployment directives. 1. Unless otherwise noted, all specifications are guaranteed over the life, operating temperatures, wavelength range, and input voltage range specified. METRO-ACCESS DWDM ERBIUM DOPED FIBER AMPLIFER Interface Specifications Parameter Specification Optical (physical) Electrical (physical) Craft Alarms Front panel LEDs Front panel configuration switch SC/UPC bulkhead, single-mode fiber (SMF) 96-pin Metral (power, alarms, craft/remote interface) Menu and TL1 interfaces through RS-232. Access depends on the mounting solution Major, Minor. Relay closed when alarm is active Power (CARD); Major Alarm (MAJ); Minor Alarm (MIN); Loss of input signal (LOS A) Two positions (booster and pre/inline amplifier) Ordering Information For more information on this or other products and their availability, please contact your local JDSU account manager or JDSU directly at 1-800-498-JDSU (5378) in North America and +800-5378-JDSU worldwide or via e-mail at [email protected]. Sample: LAP-MCH00XR00A Associated Parts Product Code LAP-MCH00XR00A Product Code 10129126 10132805 Description LightAmp Metro-Access DWDM Optical Amplifier Description DenseMount Shelf Comm Module All statements, technical information and recommendations related to the products herein are based upon information believed to be reliable or accurate. However, the accuracy or completeness thereof is not guaranteed, and no responsibility is assumed for any inaccuracies. The user assumes all risks and liability whatsoever in connection with the use of a product or its application. JDSU reserves the right to change at any time without notice the design, specifications, function, fit or form of its products described herein, including withdrawal at any time of a product offered for sale herein. JDSU makes no representations that the products herein are free from any intellectual property claims of others. Please contact JDSU for more information. BrightSwitch, FiberShelf, JDSU and the JDSU logo are trademarks of JDS Uniphase Corporation. Other trademarks are the property of their respective holders. ©2006 JDS Uniphase Corporation. All rights reserved. 21027465 Rev. 004 01/06 LIGHTAMP.DS.CMS.AE NORTH AMERICA : 800 498-JDSU (5378) WORLDWIDE : +800 5378-JDSU WEBSITE : www.jdsu.com