TC7SA34F/FU TOSHIBA CMOS Digital Integrated Circuit Silicon Monolithic TC7SA34F,TC7SA34FU Non-Inverter with 3.6 V Tolerant Input and Output Features TC7SA34F · Low voltage operation : VCC = 1.8~3.6 V · High speed operation : tpd = 2.8 ns (max) (VCC = 3.0~3.6 V) : tpd = 3.7 ns (max) (VCC = 2.3~2.7 V) : tpd = 7.4 ns (max) (VCC = 1.8 V) · High Output current : IOH/IOL = ±24 mA (min) (VCC = 3.0 V) : IOH/IOL = ±18 mA (min) (VCC = 2.3 V) : IOH/IOL = ±6 mA (min) (VCC = 1.8 V) · Latch-up performance : ±300 mA or more · ESD performance · Power down protection is provided on all inputs and outputs. TC7SA34FU : Human body model > ±200 V : Machine model > ±2000 V Weight SSOP5-P-0.95 : 0.016 g (typ.) SSOP5-P-0.65A : 0.006 g (typ.) Maximum Ratings (Ta = 25°C) Characteristics Symbol Rating Unit Power supply voltage VCC −0.5~4.6 V DC input voltage VIN −0.5~4.6 V DC output voltage VOUT Input diode current IIK −50 mA Output diode current IOK ±50 (Note 3) mA DC output current IOUT ±50 mA Power dissipation PD 200 mW DC VCC/ground current ICC ±100 mA Storage temperature range Tstg −65~150 °C −0.5~4.6 (Note 1) −0.5~VCC + 0.5 (Note 2) V Note 1: VCC = 0 V Note 2: High or low state. IOUT absolute maximum rating be observed. Note 3: VOUT < GND, VOUT > VCC 1 2002-12-13 TC7SA34F/FU Marking Pin Assignment (top view) Type name NC 1 5 VCC IN A 2 V F GND 3 Logic Diagram Truth Table 1 IN A 4 OUT Y OUT Y A Y L L H H Recommended Operating Range Characteristics Symbol Power supply voltage VCC Input voltage VIN Rating Unit 1.8~3.6 1.2~3.6 (Note 4) -0.3~3.6 V 0~3.6 (Note 5) 0~VCC (Note 6) ±24 (Note 7) ±18 (Note 8) ±6 (Note 9) Output voltage VOUT Output current IOH/IOL Operating temperature range Topr -40~85 Input rise and fall time dt/dv 0~10 V V mA °C (Note 10) ns/V Note 4: Data retention only Note 5: VCC = 0 V Note 6: High or low state Note 7: VCC = 3.0~3.6 V Note 8: VCC = 2.3~2.7 V Note 9: VCC = 1.8 V Note 10: VIN = 0.8~2.0 V, VCC = 3.0 V 2 2002-12-13 TC7SA34F/FU Electrical Characteristics < 3.6 V) DC Characteristics (Ta = -40~85°C, 2.7 V < VCC = Characteristics Symbol Test Condition Min Max Unit VCC (V) Input voltage High level VIH ¾ 2.7~3.6 2.0 ¾ Low level VIL ¾ 2.7~3.6 ¾ 0.8 IOH = -100 mA 2.7~3.6 VCC - 0.2 ¾ IOH = -12 mA 2.7 2.2 ¾ IOH = -18 mA 3.0 2.4 ¾ IOH = -24 mA 3.0 2.2 ¾ IOL = 100 mA 2.7~3.6 ¾ 0.2 IOL = 12 mA 2.7 ¾ 0.4 IOL = 18 mA 3.0 ¾ 0.4 High level VOH VIN = VIH Output voltage Low level VOL VIN = VIL IOL = 24 mA Input leakage current IIN Power off leakage current IOFF Quiescent supply current ICC Increase in ICC per input DICC V V 3.0 ¾ 0.55 2.7~3.6 ¾ ±5.0 mA 0 ¾ 10.0 mA VIN = VCC or GND 2.7~3.6 ¾ 20.0 VCC < = (VIN, VOUT) < = 3.6 V 2.7~3.6 ¾ ±20.0 VIH = VCC - 0.6 V 2.7~3.6 ¾ 750 Min Max VIN = 0~3.6 V VIN, VOUT = 0~3.6 V mA < VCC = < 2.7 V) DC Characteristics (Ta = -40~85°C, 2.3 V = Characteristics Symbol Test Condition Unit VCC (V) Input voltage High level VIH ¾ 2.3~2.7 1.6 ¾ Low level VIL ¾ 2.3~2.7 ¾ 0.7 2.3~2.7 VCC - 0.2 ¾ IOH = -6 mA 2.3 2.0 ¾ IOH = -12 mA 2.3 1.8 ¾ IOH = -18 mA 2.3 1.7 ¾ IOL = 100 mA 2.3~2.7 ¾ 0.2 IOL = 12 mA 2.3 ¾ 0.4 IOL = 18 mA 2.3 ¾ 0.6 2.3~2.7 ¾ ±5.0 mA 0 ¾ 10.0 mA VIN = VCC or GND 2.3~2.7 ¾ 20.0 VCC < = (VIN, VOUT) < = 3.6 V 2.3~2.7 ¾ ±20.0 IOH = -100 mA High level VOH VIN = VIH Output voltage Low level Input leakage current VOL IIN Power off leakage current IOFF Quiescent supply current ICC VIN = VIL VIN = 0~3.6 V VIN, VOUT = 0~3.6 V 3 V V mA 2002-12-13 TC7SA34F/FU < VCC < 2.3 V) DC Characteristics (Ta = -40~85°C, 1.8 V = Characteristics Symbol Test Condition Min Max Unit VCC (V) High level VIH ¾ 1.8~2.3 0.7 ´ VCC ¾ Low level VIL ¾ 1.8~2.3 ¾ 0.2 ´ VCC High level VOH IOH = -100 mA 1.8 VCC - 0.2 ¾ IOH = -6 mA 1.8 1.4 ¾ IOL = 100 mA 1.8 ¾ 0.2 IOL = 6 mA 1.8 ¾ 0.3 1.8 ¾ ±5.0 mA 0 ¾ 10.0 mA VIN = VCC or GND 1.8 ¾ 20.0 VCC < = (VIN, VOUT) < = 3.6 V 1.8 ¾ ±20.0 Input voltage VIN = VIH Output voltage Low level Input leakage current VOL IIN Power off leakage current IOFF Quiescent supply current ICC VIN = VIL VIN = 0~3.6 V VIN, VOUT = 0~3.6 V V V mA AC Characteristics (Ta = -40~85°C, input: tr = tf = 2.0 ns, CL = 30 pF, RL = 500 W) Characteristics Propagation delay time Symbol tpLH tpHL Test Condition Figure 1, Figure 2 Min Max 1.8 1.0 7.4 2.5 ± 0.2 0.8 3.7 3.3 ± 0.3 0.6 2.8 VCC (V) Unit ns For CL = 50 pF, add approximately 300 ps to the AC maximum specification. 4 2002-12-13 TC7SA34F/FU Dynamic Switching Characteristics (Ta = 25°C, input: tr = tf = 2.0 ns, CL = 30 pF) Characteristics Symbol Test Condition Typ. Unit VCC (V) Quiet output maximum dynamic VOL Quiet output minimum dynamic VOL Quiet output minimum dynamic VOH VOLP VOLV VOLP VIN = 1.8 V, VIL = 0 V (Note 11) 1.8 0.25 VIN = 2.5 V, VIL = 0 V (Note 11) 2.5 0.6 VIN = 3.3 V, VIL = 0 V (Note 11) 3.3 0.8 VIN = 1.8 V, VIL = 0 V (Note 11) 1.8 -0.25 VIN = 2.5 V, VIL = 0 V (Note 11) 2.5 -0.6 VIN = 3.3 V, VIL = 0 V (Note 11) 3.3 -0.8 VIN = 1.8 V, VIL = 0 V (Note 11) 1.8 1.5 VIN = 2.5 V, VIL = 0 V (Note 11) 2.5 1.9 VIN = 3.3 V, VIL = 0 V (Note 11) 3.3 2.2 ns ns ns Note 11: Parameter guaranteed by design. Capacitive Characteristics (Ta = 25°C) Characteristics Symbol Test Condition Input capacitance CIN ¾ Power dissipation capacitance CPD fIN = 10 MHz VCC (V) (Note 12) Typ. Unit 1.8, 2.5, 3.3 pF 1.8, 2.5, 3.3 pF Note 12: CPD is defined as the value of the internal equivalent capacitance which is calculated from the operating current consumption without load. Average operating current can be obtained by the equation. ICC (opr.) = CPD･VCC･fIN + ICC 5 2002-12-13 TC7SA34F/FU AC Test Circuit Output RL CL Measure CL = 30 pF RL = 500 W Figure 1 AC Wareform tr 2.0 ns 2.0 ns tf 90% Input VIH VM 10% VIL VOH Output VM tpLH tpHL Symbol Figure 2 VOL VCC 3.3 ± 0.3 V 2.5 ± 0.2 V 1.8 V VIH 2.7 V VCC VCC VM 1.5 V VCC/2 VCC/2 tpLH, tpHL 6 2002-12-13 TC7SA34F/FU Package Dimensions Weight: 0.016 g (typ.) 7 2002-12-13 TC7SA34F/FU Package Dimensions Weight: 0.006 g (typ.) 8 2002-12-13 TC7SA34F/FU RESTRICTIONS ON PRODUCT USE 000707EBA · TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability Handbook” etc.. · The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.). These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in this document shall be made at the customer’s own risk. · The products described in this document are subject to the foreign exchange and foreign trade laws. · The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA CORPORATION for any infringements of intellectual property or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any intellectual property or other rights of TOSHIBA CORPORATION or others. · The information contained herein is subject to change without notice. 9 2002-12-13