TI TPS51275

TPS51275, TPS51275C
www.ti.com
SLUSB45 – JUNE 2012
Dual Synchronous, Step-Down Controller with 5-V and 3.3-V LDOs
FEATURES
APPLICATIONS
1
•
•
2
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Input Voltage Range: 5 V to 24 V
• Notebook Computers
Output Voltages: 5 V and 3.3 V (Adjustable
• Tablet Computers
Range ±10%)
DESCRIPTION
Built-in, 100-mA, 5-V and 3.3-V LDOs
The TPS51275/C is a cost-effective, dualClock Output for Charge-Pump
synchronous buck controller targeted for notebook
±1% Reference Accuracy
system-power supply solutions. It provides 5-V and
Adaptive On-time D-CAP™ Mode Control
3.3-V LDOs and requires few external components.
The 260-kHz VCLK output can be used to drive an
Architecture with 300kHz/355kHz Frequency
external charge pump, generating gate drive voltage
Setting
for the load switches without reducing the main
Auto-skip Light Load Operation
converter efficiency. The TPS51275/C supports high
Internal 0.8-ms Voltage Servo Soft-Start
efficiency, fast transient response and provides a
combined power-good signal. Adaptive on-time, DLow-Side RDS(on) Current Sensing Scheme with
CAP™ control provides convenient and efficient
4500 ppm/°C Temperature Coefficient
operation. The device operates with supply input
Built-in Output Discharge Function
voltage ranging from 5 V to 24 V and supports output
Separate Enable Input for Switchers
voltages of 5.0 V and 3.3 V. The TPS51275/C is
available in a 20-pin, 3 mm × 3 mm, QFN package
Dedicated OC Setting Terminals
and is specified from –40°C to 85°C.
Power Good Indicator
OVP/UVP/OCP Protection
Non-latch UVLO/OTP Protection
20-Pin, 3 mm × 3 mm, QFN (RUK)
ORDERING INFORMATION (1)
ORDERABLE
DEVICE NUMBER
ENABLE
FUNCTION
TPS51275RUKR
TPS51275RUKT
TPS51275CRUKR
PACKAGE
VREG3
PLASTIC Quad Flat
Pack
(20 pin QFN)
EN1 and EN2
TPS51275CRUKT
(1)
ALWAYS ON-LDO
VREG3 and VREG5
OUTPUT SUPPLY
QUANTITY
Tape and Reel
3000
Mini reel
250
Tape and Reel
3000
Mini reel
250
For the most current package and ordering information see the Package Option Addendum at the end of this document, or see the TI
website at www.ti.com.
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
D-CAP is a trademark of Texas Instruments.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2012, Texas Instruments Incorporated
TPS51275, TPS51275C
SLUSB45 – JUNE 2012
www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
TYPICAL APPLICATION DIAGRAM (TPS51275)
VIN
TPS51275
VIN
VOUT
5V
VBST1
VBST2
DRVH1
DRVH 2
SW1
VOUT
3.3 V
SW2
DRVL1
DRVL2
VO1
VFB1
VFB2
CS1
CS2
VCLK
VOUT
15 V
EN-5V
PGOOD
EN1
5V
PGOOD
EN2
VREG5
EN 3.3 V
VREG3
1 mF
3.3-V Always ON
1 mF
UDG-12090
TYPICAL APPLICATION DIAGRAM (TPS51275C)
VIN
TPS51275C
VIN
VOUT
5V
VBST1
VBST2
DRVH1
DRVH 2
SW1
DRVL1
VOUT
3.3 V
SW2
DRVL2
VO1
VFB1
EN 5 V
CS1
CS2
EN1
PGOOD
VCLK
VOUT
15 V
5V
Always ON
VREG5
1 mF
VFB2
PGOOD
EN2
EN 3.3 V
VREG3
3.3-V Always ON
1 mF
UDG-12091
2
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
TPS51275, TPS51275C
www.ti.com
SLUSB45 – JUNE 2012
ABSOLUTE MAXIMUM RATINGS (1)
over operating free-air temperature range (unless otherwise noted)
VALUE
Input voltage (2)
MIN
MAX
VBST1, VBST2
–0.3
32
VBST1, VBST2 (3)
–0.3
6
SW1, SW2
–6.0
26
VIN
–0.3
26
EN1, EN2
–0.3
6
VFB1, VFB2
–0.3
3.6
VO1
–0.3
6
DRVH1, DRVH2
–6.0
32
–0.3
6
DRVH1, DRVH2 (3)
DRVH1, DRVH2
Output voltage (2)
Electrostatic
discharge
(3)
–2.5
6
DRVL1, DRVL2
(pulse width < 20 ns)
–0.3
6
DRVL1, DRVL2 (pulse width < 20 ns)
–2.5
6
PGOOD, VCLK, VREG5
–0.3
6
VREG3, CS1, CS2
–0.3
3.6
HBM QSS 009-105 (JESD22-A114A)
2
CDM QSS 009-147 (JESD22-C101B.01)
1
Junction temperature, TJ
150
Storage temperature, TST
–55
(1)
(2)
(3)
UNIT
V
V
kV
°C
150
°C
Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings
only and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating
conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltage values are with respect to the network ground terminal unless otherwise noted
Voltage values are with respect to SW terminals.
THERMAL INFORMATION
THERMAL METRIC (1)
TPS51275
TPS51275C
UNITS
20-PIN RUK
θJA
Junction-to-ambient thermal resistance
94.1
θJCtop
Junction-to-case (top) thermal resistance
58.1
θJB
Junction-to-board thermal resistance
64.3
ψJT
Junction-to-top characterization parameter
31.8
ψJB
Junction-to-board characterization parameter
58.0
θJCbot
Junction-to-case (bottom) thermal resistance
5.9
(1)
°C/W
For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
Copyright © 2012, Texas Instruments Incorporated
Submit Documentation Feedback
3
TPS51275, TPS51275C
SLUSB45 – JUNE 2012
www.ti.com
RECOMMENDED OPERATING CONDITIONS
over operating free-air temperature range (unless otherwise noted)
Supply voltage
Input voltage (1)
Output voltage (1)
VIN
4
TYP MAX
5
24
VBST1, VBST2
–0.1
30
VBST1, VBST2 (2)
–0.1
5.5
SW1, SW2
–5.5
24
EN1, EN2
–0.1
5.5
VFB1, VFB2
–0.1
3.5
VO1
–0.1
5.5
DRVH1, DRVH2
–5.5
30
DRVH1, DRVH2 (2)
–0.1
5.5
DRVL1, DRVL2
–0.1
5.5
PGOOD, VCLK, VREG5
–0.1
5.5
VREG3, CS1, CS2
–0.1
3.5
–40
85
Operating free-air temperature, TA
(1)
(2)
MIN
UNIT
V
V
°C
All voltage values are with respect to the network ground terminal unless otherwise noted.
Voltage values are with respect to the SW terminal.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
TPS51275, TPS51275C
www.ti.com
SLUSB45 – JUNE 2012
ELECTRICAL CHARACTERISTICS
over operating free-air temperature range, VVIN= 12 V, VVO1= 5 V, VVFB1= VVFB2= 2 V, VEN1= VEN2= 3.3 V (unless otherwise
noted)
PARAMETER
TEST CONDITION
MIN
TYP
MAX
UNIT
SUPPLY CURRENT
IVIN1
VIN supply current-1
TA = 25°C, No load, VVO1=0 V
IVIN2
VIN supply current-2
TA = 25°C, No load
IVO1
VO1 supply current
TA = 25°C, No load, VVFB1= VVFB2=2.05 V
IVIN(STBY)
VIN stand-by current
IVIN(STBY)
VIN stand-by current
T = 25°C, No load, VVO1= 0 V,
TPS51275 A
VEN1= VEN2= 0 V
TA = 25°C, No load, VVO1=0 V, VEN1=VEN2=0V
(TPS51275C)
860
μA
30
μA
900
μA
95
μA
180
μA
INTERNAL REFERENCE
VFBx
VFB regulation voltage
TA = 25°C
1.99
2.00
2.01
V
1.98
2.00
2.02
V
VREG5 OUTPUT
TA = 25°C, No load, VVO1= 0 V
4.9
5.0
5.1
VVIN> 7 V , VVO1= 0 V, IVREG5< 100 mA
4.85
5.00
5.10
VVIN > 5.5 V , VVO1= 0 V, IVREG5< 35 mA
4.85
5.00
5.10
5.10
VVREG5
VREG5 output voltage
V
VVIN > 5 V, VVO1= 0 V, IVREG5< 20 mA
4.50
4.75
IVREG5
VREG5 current limit
VVO1= 0 V, VVREG5= 4.5 V, VVIN= 7 V
100
150
mA
RV5SW
5-V switch resistance
TA = 25°C, VVO1= 5 V, IVREG5= 50 mA
1.8
Ω
VREG3 OUTPUT
VVREG3
IVREG3
VREG3 output voltage
VREG3 current limit
TA = 25°C, No load, VVO1= 0 V
3.267
3.300
3.333
VVIN > 7 V , VVO1= 0 V, IVREG3< 100 mA
3.217
3.300
3.383
5.5 V < VVIN , VVO1= 0 V, IVREG3< 35 mA
3.234
3.300
3.366
0°C ≤ TA ≤ 85°C, VVIN > 5.5 V, VVO1= 0 V, IVREG3< 35
mA
3.267
3.300
3.333
VVIN > 5 V, VVO1= 0 V, IVREG3< 35 mA
3.366
3.217
3.300
VVO1= 0 V, VVREG3= 3.0 V, VVIN= 7 V
100
150
V
mA
DUTY CYCLE and FREQUENCY CONTROL
fsw1
CH1 frequency (1)
TA = 25°C, VVIN= 20 V
240
300
360
kHz
fSW2
CH2 frequency (1)
TA = 25°C, VVIN= 20 V
280
355
430
kHz
TOFF(MIN)
Minimum off-time
TA = 25°C
200
300
500
ns
MOSFET DRIVERS
Source, (VVBST – VDRVH) = 0.25 V, (VVBST – VSW) = 5 V
3.0
Sink, (VDRVH – VSW) = 0.25 V, (VVBST – VSW) = 5 V
1.9
Source, (VVREG5 – VDRVL) = 0.25 V, VVREG5 = 5 V
3.0
Sink, VDRVL = 0.25 V, VVREG5= 5 V
0.9
DRVH-off to DRVL-on
12
DRVL-off to DRVH-on
20
Boost switch on-resistance
TA = 25°C, IVBST = 10 mA
13
VBST leakage current
TA = 25°C
RDRVH
DRVH resistance
RDRVL
DRVL resistance
tD
Dead time
Ω
Ω
ns
INTERNAL BOOT STRAP SWITCH
RVBST
(ON)
IVBSTLK
Ω
1
µA
CLOCK OUTPUT
RVCLK
(PU)
VCLK on-resistance (pull-up)
TA = 25°C
10
RVCLK
(PD)
VCLK on-resistance (pull-down)
TA = 25°C
10
Clock frequency
TA = 25°C
260
fCLK
(1)
Ω
kHz
Ensured by design. Not production tested.
Copyright © 2012, Texas Instruments Incorporated
Submit Documentation Feedback
5
TPS51275, TPS51275C
SLUSB45 – JUNE 2012
www.ti.com
ELECTRICAL CHARACTERISTICS
over operating free-air temperature range, VVIN= 12 V, VVO1= 5 V, VVFB1= VVFB2= 2 V, VEN1= VEN2= 3.3 V (unless otherwise
noted)
PARAMETER
TEST CONDITION
MIN
TYP
MAX
UNIT
OUTPUT DISCHARGE
RDIS1
CH1 discharge resistance
RDIS2
CH2 discharge resistance
RDIS2
CH2 discharge resistance
TPS51275
TA = 25°C, VVO1 = 0.5 V
VEN1 = VEN2 = 0 V
35
Ω
TA = 25°C, VSW2 = 0.5 V
VEN1 = VEN2 = 0 V
75
Ω
TA = 25°C, VSW2 = 0.5 V, VEN1 = VEN2 = 0 V
(TPS51275C)
70
Ω
SOFT START OPERATION
tSS
Soft-start time
From ENx="Hi" and VVREG5 > VUVLO5 to VOUT = 95%
0.91
ms
tSSRAMP
Soft-start time (ramp-up)
VOUT= 0% to VOUT = 95%, VVREG5 = 5 V
0.78
ms
POWER GOOD
Lower (rising edge of PG-in)
VPGTH
PG threshold
92.5%
Hysteresis
95.0%
97.5%
5%
Upper (rising edge of PG-out)
107.5% 110.0% 112.5%
Hysteresis
5%
6.5
IPGMAX
PG sink current
VPGOOD = 0.5 V
IPGLK
PG leak current
VPGOOD = 5.5 V
tPGDEL
PG delay
From PG lower threshold (95%=typ) to PG flag high
mA
1
0.7
µA
ms
CURRENT SENSING
ICS
CS source current
TA = 25°C, VCS= 0.4 V
TCCS
CS current temperature coefficient (1)
On the basis of 25°C
VCS
CS Current limit setting range
VZC
Zero cross detection offset
9
10
0.2
TA = 25°C
11
4500
–1
1
μA
ppm/°C
2
V
3
mV
LOGIC THRESHOLD
VENX(ON)
EN threshold high-level
SMPS on level
VENX(OFF)
EN threshold low-level
SMPS off level
0.3
1.6
IEN
EN input current
VENx= 3.3 V
–1
V
V
1
µA
OUTPUT OVERVOLTAGE PROTECTION
VOVP
OVP trip threshold
tOVPDLY
OVP propagation delay
112.5% 115.0% 117.5%
TA = 25°C
0.5
µs
OUTPUT UNDERVOLTAGE PROTECTION
VUVP
UVP trip Threshold
tUVPDLY
UVP prop delay
tUVPENDLY
UVP enable delay
55%
60%
65%
250
µs
From ENx ="Hi", VVREG5 = 5 V
1.35
ms
Wake up
4.58
V
UVLO
VUVL0VIN
VUVLO5
VUVLO3
VIN UVLO Threshold
VREG5 UVLO Threshold
VREG3 UVLO Threshold
Hysteresis
Wake up
Hysteresis
0.5
4.38
V
4.50
V
0.4
V
Wake up
3.15
V
Hysteresis
0.15
V
Shutdown temperature
155
OVER TEMPERATURE PROTECTION
TOTP
(1)
6
OTP threshold (1)
Hysteresis
10
°C
Ensured by design. Not production tested.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
TPS51275, TPS51275C
www.ti.com
SLUSB45 – JUNE 2012
DEVICE INFORMATION
3
VFB2
4
CS2
5
VCLK
SW1
VBST1
DRVH1
16
TPS51275
TPS51275C
Thermal Pad
6
7
8
9
10
DRVH2
VREG3
17
VBST2
2
18
SW2
VFB1
19
PGOOD
1
20
EN2
CS1
EN1
RUK PACKAGE
20 PINS
(TOP VIEW)
15
DRVL1
14
VO1
13
VREG5
12
VIN
11
DRVL2
PIN FUNCTIONS
PIN NO.
NAME
TPS51275
TPS51275C
I/O
CS1
1
O
Sets the channel 1 OCL trip level.
CS2
5
O
Sets the channel 2OCL trip level.
DRVH1
16
O
High-side driver output
DRVH2
10
O
High-side driver output
DRVL1
15
O
Low-side driver output
DRVL2
11
O
Low-side driver output
EN1
20
I
Channel 1 enable.
EN2
6
I
Channel 2 enable.
PGOOD
7
O
Power good output flag. Open drain output. Pull up to external rail via a resistor
SW1
18
O
Switch-node connection.
SW2
8
O
Switch-node connection.
VBST1
17
I
VBST2
9
I
Supply input for high-side MOSFET (bootstrap terminal). Connect capacitor from this pin to SW
terminal.
VCLK
19
O
Clock output for charge pump.
VFB1
2
I
VFB2
4
I
VIN
12
I
Power conversion voltage input. Apply the same voltage as drain voltage of high-side MOSFETs of
channel 1 and channel 2.
VO1
14
I
Output voltage input, 5-V input for switch-over.
VREG3
3
O
3.3-V LDO output.
VREG5
13
O
5-V LDO output.
Thermal pad
DESCRIPTION
Voltage feedback Input
GND terminal, solder to the ground plane
Copyright © 2012, Texas Instruments Incorporated
Submit Documentation Feedback
7
TPS51275, TPS51275C
SLUSB45 – JUNE 2012
www.ti.com
FUNCTIONAL BLOCK DIAGRAM (TPS51275/C)
TPS51275
TPS51275C
VIN
+
+
155°C/145°C
4.5 V/4.0 V
VO1
+
VREG5
+
+
+
2V
+
VREG3
Osc
VCLK
EN1
VBST1
EN2
VDRV
VIN VDD VO_OK
EN
DRVH 1
SW1
DRVL 1
Switcher
Controller
(CH1)
VFB1
CS1
VDD VDRV
FAULT
FAULT
REF
REF
GND
Switcher
Controller
(CH2)
PGOOD
DCHG
DCHG
VBST2
DRVH 2
EN
PGOOD
PGND
VIN
SW2
DRVL 2
VFB2
GND
PGND
CS2
PGOOD
GND
(Thermal Pad )
8
Submit Documentation Feedback
UDG-12092
Copyright © 2012, Texas Instruments Incorporated
TPS51275, TPS51275C
www.ti.com
SLUSB45 – JUNE 2012
SWITCHER CONTROLLER BLOCK DIAGRAM
TPS51275
TPS51275C
VDD
VREF –40%
VREF +15%
+
UV
VREF +5%/10%
+
+
OV
Control Logic
+
VREF –5%/10%
VFB
EN
REF
SS Ramp Comp
+
+
PWM
VO_OK
VBST
SKIP
HS
VIN
DRVH
SW
XCON
OC
CS
10 µA
VDRV
+
+
LS
NOC
One-Shot
+
Discharge
GND
+
ZC
DRVL
PGND
DCHG
PGOOD
PGOOD
FAULT
UDG-12093
Copyright © 2012, Texas Instruments Incorporated
Submit Documentation Feedback
9
TPS51275, TPS51275C
SLUSB45 – JUNE 2012
www.ti.com
DETAILED DESCRIPTION
PWM Operations
The main control loop of the switch mode power supply (SMPS) is designed as an adaptive on-time pulse width
modulation (PWM) controller. It supports a proprietary D-CAP™ mode. D-CAP™ mode does not require external
conpensation circuit and is suitable for low external component count configuration when used with appropriate
amount of ESR at the output capacitor(s).
At the beginning of each cycle, the synchronous high-side MOSFET is turned on, or enters the ON state. This
MOSFET is turned off, or enters the ‘OFF state, after the internal, one-shot timer expires. The MOSFET is turned
on again when the feedback point voltage, VVFB, decreased to match the internal 2-V reference. The inductor
current information is also monitored and should be below the overcurrent threshold to initiate this new cycle. By
repeating the operation in this manner, the controller regulates the output voltage. The synchronous low-side
(rectifying) MOSFET is turned on at the beginning of each OFF state to maintain a minimum of conduction loss.
The low-side MOSFET is turned off before the high-side MOSFET turns on at next switching cycle or when
inductor current information detects zero level. This enables seamless transition to the reduced frequency
operation during light-load conditions so that high efficiency is maintained over a broad range of load current.
Adaptive On-Time/ PWM Frequency Control
Bacause the TPS51275/C does not have a dedicated oscillator for control loop on board, switching cycle is
controlled by the adaptive on-time circuit. The on-time is controlled to meet the target switching frequency by
feed-forwarding the input and output voltage into the on-time one-shot timer. The target switching frequency is
varied according to the input voltage to achieve higher duty operation for lower input voltage application. The
switching frequency of CH1 (5-V output) is 300 kHz during continuous conduction mode (CCM) operation when
VIN = 20 V. The CH2 (3.3-V output) is 355 kHz during CCM when VIN = 20 V. (See Figure 21 and Figure 22).
To improve load transient performance and load regulation in lower input voltage conditions, TPS51275/C can
extend the on-time. The maximum on-time extension of CH1 is 4 times for CH2 is 3 times. To maintain a
reasonable inductor ripple current during on-time extension, the inductor ripple current should be set to less than
half of the OCL (valley) threshold. (See Step 2. Choose the Inductor). The on-time extension function provides
high duty cycle operation and shows better DC (static) performance. AC performance is determined mostly by
the output LC filter and resistive factor in the loop.
Light Load Condition in Auto-Skip Operation (TPS51275/C)
The TPS51275/C automatically reduces switching frequency during light-load conditions to maintain high
efficiency. This reduction of frequency is achieved smoothly and without an increase in output voltage ripple. A
more detailed description of this operation is as follows. As the output current decreases from heavy-load
condition, the inductor current is also reduced and eventually approaches valley zero current, which is the
boundary between continuous conduction mode and discontinuous conduction mode. The rectifying MOSFET is
turned off when this zero inductor current is detected. As the load current further decreases, the converter runs in
discontinuous conduction mode and it takes longer and longer to discharge the output capacitor to the level that
requires the next ON cycle. The ON time is maintained the same as that in the heavy-load condition. In reverse,
when the output current increase from light load to heavy load, the switching frequency increases to the preset
value as the inductor current reaches to the continuous conduction. The transition load point to the light load
operation IOUT(LL) (i.e. the threshold between continuous and discontinuous conduction mode) can be calculated
as shown in Equation 1.
IOUT(LL ) =
(VIN - VOUT )´ VOUT
1
´
2 ´ L ´ fSW
VIN
where
•
fSW is the PWM switching frequency
(1)
Switching frequency versus output current during light-load conditions is a function of inductance (L), input
voltage (VIN) and output voltage (VOUT), but it decreases almost proportional to the output current from the
IOUT(LL).
10
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
TPS51275, TPS51275C
www.ti.com
SLUSB45 – JUNE 2012
D-CAP™ Mode
From small-signal loop analysis, a buck converter using D-CAP™ mode can be simplified as shown in Figure 1.
TPS51275
TPS51275C
Switching Modulator
VIN
DRVH
R1
R2
L
VFB
PWM
+
+
Control
Logic
and
Divider
VOUT
DRVL
IIND
IOUT
IC
VREF
ESR
RLOAD
Voltage
Divider
VC
COUT
Output
Capacitor
UDG-12111
Figure 1. Simplifying the Modulator
The output voltage is compared with internal reference voltage after divider resistors, R1 and R2. The PWM
comparator determines the timing to turn onthe high-side MOSFET. The gain and speed of the comparator is
high enough to keep the voltage at the beginning of each ON cycle substantially constant. For the loop stability,
the 0dB frequency, ƒ0, defined in Equation 2 must be lower than 1/4 of the switching frequency.
f
1
£ SW
f0 =
2p ´ ESR ´ COUT
4
(2)
As ƒ0 is determined solely by the output capacitor characteristics, the loop stability during D-CAP™ mode is
determined by the capacitor chemistry. For example, specialty polymer capacitors have output capacitance in the
order of several hundred micro-Farads and ESR in range of 10 milli-ohms. These yield an f0 value on the order
of 100 kHz or less and the loop is stable. However, ceramic capacitors have ƒ0 at more than 700 kHz, which is
not suitable for this operational mode.
Copyright © 2012, Texas Instruments Incorporated
Submit Documentation Feedback
11
TPS51275, TPS51275C
SLUSB45 – JUNE 2012
www.ti.com
Enable and Powergood
VREG3 is an always-on regulator (TPS51275), VREG3/VREG5 are always-on regulators (TPS51275C), when
the input voltage is beyond the UVLO threshold it turns ON. VREG5 is turned ON when either EN1 or EN2
enters the ON state. The VCLK signal initiates when EN1 enters the ON state (TPS51275/C). Enable states are
shown in Table 1 through Table 2.
Table 1. Enabling/PGOOD State (TPS51275)
EN1
EN2
VREG5
VREG3
CH1 (5Vout)
CH2 (3.3Vout)
VCLK
PGOOD
OFF
OFF
OFF
ON
OFF
OFF
OFF
Low
Low
ON
OFF
ON
ON
ON
OFF
ON
OFF
ON
ON
ON
OFF
ON
OFF
Low
ON
ON
ON
ON
ON
ON
ON
High
Table 2. Enabling/PGOOD State (TPS51275C)
EN1
EN2
VREG5
VREG3
CH1 (5Vout)
CH2 (3.3Vout)
VCLK
PGOOD
OFF
OFF
ON
ON
OFF
OFF
OFF
Low
ON
OFF
ON
ON
ON
OFF
ON
Low
OFF
ON
ON
ON
OFF
ON
OFF
Low
ON
ON
ON
ON
ON
ON
ON
High
VIN-UVLO_threshold
VIN
VREG3
EN_threshold
EN1
VREG5-UVLO_threshold
VREG5
95% of VOUT
Soft-Start Time (tSS)
Soft-Start Time
(tSS(ramp))
5-V VOUT
EN_threshold
EN2
95% of Vout
3.3-V VOUT
Soft-Start Time (tSS)
PGOOD
Soft-Start Time
(tSS(ramp))
PGOOD
Delay
tPGDEL
UDG-12013
Figure 2. TPS51275 Timing
12
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
TPS51275, TPS51275C
www.ti.com
SLUSB45 – JUNE 2012
VIN-UVLO_threshold
VIN
2.4 V
VREG3
VREG5
EN_threshold
EN1
95% of VOUT
Soft-Start Time (tSS)
Soft-Start Time
(tSS(ramp))
5-V VOUT
EN_threshold
EN2
95% of Vout
3.3-V VOUT
Soft-Start Time (tSS)
PGOOD
Soft-Start Time
(tSS(ramp))
PGOOD
Delay
tPGDEL
UDG-12015
Figure 3. TPS51275C Timing
Copyright © 2012, Texas Instruments Incorporated
Submit Documentation Feedback
13
TPS51275, TPS51275C
SLUSB45 – JUNE 2012
www.ti.com
Soft-Start and Discharge
The TPS51275/C operates an internal, 0.8-ms, voltage servo soft-start for each channel. When the ENx pin
becomes higher than the enable threshold voltage, an internal DAC begins ramping up the reference voltage to
the PWM comparator. Smooth control of the output voltage is maintained during start-up. When ENx becomes
lower than the lower level of threshold voltage, TPS51275/C discharges outputs using internal MOSFETs through
VO1 (CH1) and SW2 (CH2).
VREG5/VREG3 Linear Regulators
There are two sets of 100-mA standby linear regulators which output 5 V and 3.3 V, respectively. The VREG5
pin provides the current for the gate drivers. The VREG3 pin functions as the main power supply for the analog
circuitry of the device. VREG3 is an Always ON LDO and TPS51275C has Always ON VREG5. (See Table 1 and
Table 2)
Add ceramic capacitors with a value of 1 µF or larger (X5R grade or better) placed close to the VREG5 and
VREG3 pins to stabilize LDOs.
The VREG5 pin switchover function is asserted when three conditions are present:
• CH1 internal PGOOD is high
• CH1 is not in OCL condition
• VO1 voltage is higher than VREG5-1V
In
•
•
•
this switchover condition, three things occur:
the internal 5-V, LDO regulator is shut off
the VREG5 output is connected to VO1 by internal switchover MOSFET
VREG3 input pass is changed from VIN to VO1
VCLK for Charge Pump
The 260-kHz VCLK signal can be used in the charge pump circuit. The VCLK signal becomes available when
EN1. The VCLK driver is driven by VO1 voltage. In a design that does not require VCLK output, leave the VCLK
pin open.
Overcurrent Protection
TPS51275/C has cycle-by-cycle over current limiting control. The inductor current is monitored during the OFF
state and the controller maintains the OFF state during the inductor current is larger than the overcurrent trip
level. In order to provide both good accuracy and cost effective solution, TPS51275/C supports temperature
compensated MOSFET RDS(on) sensing. The CSx pin should be connected to GND through the CS voltage
setting resistor, RCS. The CSx pin sources CS current (ICS) which is 10 µA typically at room temperature, and the
CSx terminal voltage (VCS= RCS × ICS) should be in the range of 0.2 V to 2 V over all operation temperatures.
The trip level is set to the OCL trip voltage (VTRIP) as shown in Equation 3.
R ´I
VTRIP = CS CS + 1 mV
8
(3)
The inductor current is monitored by the voltage between GND pin and SWx pin so that SWx pin should be
connected to the drain terminal of the low-side MOSFET properly.The CS pin current has a 4500 ppm/°C
temperature slope to compensate the temperature dependency of the RDS(on). GND is used as the positive
current sensing node so that GND should be connected to the source terminal of the low-side MOSFET.
As the comparison is done during the OFF state, VTRIP sets the valley level of the inductor current. Thus, the load
current at the overcurrent threshold, IOCP, can be calculated as shown in Equation 4.
IIND(ripple )
(VIN - VOUT )´ VOUT
V
V
1
IOCP = TRIP +
= TRIP +
´
RDS(on )
2
RDS(on ) 2 ´ L ´ fSW
VIN
(4)
In an overcurrent condition, the current to the load exceeds the current to the output capacitor thus the output
voltage tends to fall down. Eventually, it ends up with crossing the undervoltage protection threshold and
shutdown both channels.
14
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
TPS51275, TPS51275C
www.ti.com
SLUSB45 – JUNE 2012
Output Overvoltage/Undervoltage Protection
TPS51275/C asserts the overvoltage protection (OVP) when VFBx voltage reaches OVP trip threshold level.
When an OVP event is detected, the controller changes the output target voltage to 0 V. This usually turns off
DRVH and forces DRVL to be on. When the inductor current begins to flow through the low-side MOSFET and
reaches the negative OCL, DRVL is turned off and DRVH is turned on. After the on-time expires, DRVH is turned
off and DRVL is turned on again. This action minimizes the output node undershoot due to LC resonance. When
the VFBx reaches 0V, the driver output is latched as DRVH off, DRVL on. The undervoltage protection (UVP)
latch is set when the VFBx voltage remains lower than UVP trip threshold voltage for 250 µs or longer. In this
fault condition, the controller latches DRVH low and DRVL low and discharges the outputs. UVP detection
function is enabled after 1.35 ms of SMPS operation to ensure startup.
Undervoltage Lockout (UVLO) Protection
TPS51275/C has undervoltage lock out protection at VIN, VREG5 and VREG3. When each voltage is lower than
their UVLO threshold voltage, both SMPS are shut-off. They are non-latch protections.
Over-Temperature Protection
TPS51275/C features an internal temperature monitor. If the temperature exceeds the threshold value (typically
155°C), TPS51275/C is shut off including LDOs. This is non-latch protection.
Copyright © 2012, Texas Instruments Incorporated
Submit Documentation Feedback
15
TPS51275, TPS51275C
SLUSB45 – JUNE 2012
www.ti.com
External Components Selection
The external components selection is relatively simple for a design using D-CAP™ mode.
Step 1. Determine the Value of R1 and R2
The recommended R2 value is between 10 kΩ and 20 kΩ. Determine R1 using Equation 5.
R1 =
(VOUT - 0.5 ´ VRIPPLE - 2.0 ) ´ R2
2.0
(5)
Step 2. Choose the Inductor
The inductance value should be determined to give the ripple current of approximately 1/3 of maximum output
current and less than half of OCL (valley) threshold. Larger ripple current increases output ripple voltage,
improves signal:noise ratio, and helps ensure stable operation.
L=
IN(max ) - VOUT
1
IIND(ripple ) ´ fSW
´
(V
)´ V
OUT
VIN(max )
=
3
IOUT(max ) ´ fSW
IN(max ) - VOUT
´
(V
)´ V
OUT
VIN(max)
(6)
The inductor also needs to have low DCR to achieve good efficiency, as well as enough room above peak
inductor current before saturation. The peak inductor current can be estimated as shown in Equation 7.
IIND(peak ) =
VIN(max ) - VOUT ´ VOUT
VTRIP
1
+
´
RDS(on ) L ´ fSW
VIN(max )
)
(
(7)
Step 3. Choose Output Capacitor(s)
Organic semiconductor capacitor(s) or specialty polymer capacitor(s) are recommended. Determine ESR to meet
required ripple voltage above. A quick approximation is as shown in Equation 8.
V
´ 20mV ´ (1 - D) 20mV ´ L ´ fSW
ESR = OUT
=
2 V ´ IIND(ripple )
2V
where
•
•
D as the duty-cycle factor
the required output ripple voltage slope is approximately 20 mV per tSW (switching period) in terms of VFB
terminal
(8)
VVOUT
Slope (1)
Jitter
(2)
Slope (2)
Jitter
20 mV
(1)
VREF
VREF +Noise
tON
tOFF
UDG-12012
Figure 4. Ripple Voltage Slope and Jitter Performance
16
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
TPS51275, TPS51275C
www.ti.com
SLUSB45 – JUNE 2012
Layout Considerations
Good layout is essential for stable power supply operation. Follow these guidelines for an efficient PCB layout.
Placement
• Place voltage setting resistors close to the device pins.
• Place bypass capacitors for VREG5 and VREG3 close to the device pins.
Routing (Sensitive analog portion)
• Use small copper space for VFBx. There are short and narrow traces to avoid noise coupling.
• Connect VFB resistor trace to the positive node of the output capacitor. Routing inner layer away from power
traces is recommended.
• Use short and wide trace from VFB resistor to vias to GND (internal GND plane).
Routing (Power portion)
• Use wider/shorter traces of DRVL for low-side gate drivers to reduce stray inductance.
• Use the parallel traces of SW and DRVH for high-side MOSFET gate drive in a same layer or on adjoin
layers, and keep them away from DRVL.
• Use wider/ shorter traces between the source terminal of the high-side MOSFET and the drain terminal of the
low-side MOSFET
• Thermal pad is the GND terminal of this device. Five or more vias with 0.33-mm (13-mils) diameter connected
from the thermal pad to the internal GND plane should be used to have strong GND connection and help heat
dissipation.
Copyright © 2012, Texas Instruments Incorporated
Submit Documentation Feedback
17
TPS51275, TPS51275C
SLUSB45 – JUNE 2012
www.ti.com
TYPICAL CHARACTERISTICS
1.6
60
VIN Supply Current 2 (µA)
VIN Supply Current 1 (mA)
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0.0
−40 −25 −10
5
20 35 50 65 80
Junction Temperature (°C)
95
20
10
1.6
250
1.4
225
1.2
1.0
0.8
0.6
0.4
0.0
−40 −25 −10
5
20 35 50 65 80
Junction Temperature (°C)
95
125
100
75
50
TPS51275
TPS51275C
300
16
290
VCLK Frequency (kHz)
310
18
8
6
4
2
5
20 35 50 65 80
Junction Temperature (°C)
95
110 125
G004
Figure 8. VIN Stand-By Current vs. Junction Temperature
20
10
G002
150
G003
12
110 125
175
0
−40 −25 −10
110 125
14
95
200
25
Figure 7. VO1 Supply Current 1 vs. Junction Temperature
0
−40 −25 −10
5
20 35 50 65 80
Junction Temperature (°C)
Figure 6. VIN Supply Current 2 vs. Junction Temperature
VIN Stand−By Current (µA)
VO1 Supply Current 1 (mA)
30
G001
0.2
CS Source Current (µA)
40
0
−40 −25 −10
110 125
Figure 5. VIN Supply Current 1 vs. Junction Temperature
280
270
260
250
240
230
220
5
20 35 50 65 80
Junction Temperature (°C)
95
110 125
G005
Figure 9. CS Source Current vs. Junction Temperature
18
50
Submit Documentation Feedback
210
−40 −25 −10
5
20 35 50 65 80
Junction Temperature (°C)
95
110 125
G006
Figure 10. Clock Frequency vs. Junction Temperature
Copyright © 2012, Texas Instruments Incorporated
TPS51275, TPS51275C
www.ti.com
SLUSB45 – JUNE 2012
TYPICAL CHARACTERISTICS (continued)
5.15
100
VVOUT1 = 5 V
VVOUT1 = 5 V
5.10
Output Volage (V)
Efficiency (%)
90
80
70
60
VVIN = 7.4 V
VVIN = 11.1 V
VVIN = 14.8 V
VVIN = 20 V
50
40
0.001
0.01
0.1
Output Current (A)
1
5.05
5.00
4.95
VVIN = 7.4 V
VVIN = 11.1 V
VVIN = 14.8 V
VVIN = 20 V
4.90
10
4.85
0.001
G000
0.01
Figure 11. Efficiency vs. Output Current
0.1
Output Current (A)
1
10
G014
Figure 12. Load Regulation
100
3.40
VVOUT2 = 3.3 V
VVOUT2 = 3.3 V
Output Volage (V)
Efficiency (%)
90
80
70
60
VVIN = 7.4 V
VVIN = 11.1 V
VVIN = 14.8 V
VVIN = 20 V
50
40
0.001
0.01
0.1
Output Current (A)
1
3.35
3.30
3.20
0.001
10
1
10
G014
450
VVIN = 7.4 V
VVIN = 12.6 V
VVIN = 20 V
400
Switching Frequency (kHz)
Switching Frequency (kHz)
0.1
Output Current (A)
Figure 14. Load Regulation
350
250
200
150
100
50
0.01
0.1
Output Current (A)
1
Figure 15. Switching Frequency vs. Output Current
Copyright © 2012, Texas Instruments Incorporated
350
VVIN = 7.4 V
VVIN = 12.6 V
VVIN = 20 V
300
250
200
150
100
50
VVOUT1 = 5 V
0
0.001
0.01
G000
Figure 13. Efficiency vs. Output Current
300
VVIN = 7.4 V
VVIN = 11.1 V
VVIN = 14.8 V
VVIN = 20 V
3.25
10
G000
0
0.001
VVOUT2 = 3.3 V
0.01
0.1
Output Current (A)
1
10
G000
Figure 16. Switching Frequency vs. Output Current
Submit Documentation Feedback
19
TPS51275, TPS51275C
SLUSB45 – JUNE 2012
www.ti.com
TYPICAL CHARACTERISTICS (continued)
VOUT1 (2 V/div)
VOUT1 (2 V/div)
VOUT2 (2 V/div)
VOUT2 (2 V/div)
PGOOD (5 V/div)
PGOOD (5 V/div)
EN1 = EN2 (5 V/div)
EN1 = EN2 (5 V/div)
Time (10 ms/div)
Time (400 µs/div)
Figure 17. Start-Up
Figure 18. Output Discharge
IOUT1 = 0 A
IOUT1: 0 A ßà 3 A
V OUT1 (100 mV/div)
IOUT2 = 0 A
VOUT1 (100 mV /div)
IOUT2: 0 A ßà 3 A
VVIN = 7 .4 V
VVIN = 7 .4 V
VOUT2 (100 mV/div)
VOUT2 ( 100 mV/div)
IIND1 (5 A /div)
IIND2 (5 A/div)
SW1 (10 V/div)
SW 2 (10 V /div)
Time (100 µs/div)
Time (100 µs/div)
Figure 19. 5-V Load Transient
Figure 20. 3.3-V Load Transient
500
500
VOUT1 = 5 V
IOUT1 = 6 A
400
350
300
250
200
150
100
50
0
400
350
300
250
200
150
100
50
5
10
15
Input Voltage (V)
20
25
Figure 21. Switching Frequency vs. Input Voltage
20
VOUT2 = 3.3 V
IOUT2 = 6 A
450
Switching Frequency (kHz)
Switching Frequency (kHz)
450
Submit Documentation Feedback
G000
0
5
10
15
Input Voltage (V)
20
25
G000
Figure 22. Switching Frequency vs. Input Voltage
Copyright © 2012, Texas Instruments Incorporated
TPS51275, TPS51275C
www.ti.com
SLUSB45 – JUNE 2012
APPLICATION DIAGRAM (TPS51275/TPS51275C)
VIN
10 µF x 2
U1
TPS51275
TPS51275C
10 µF x 2
Q1
6.8 W
12 VIN
0.1 µF
0.1 µF
17 VBST1
VBST2
16 DRVH 1
DRVH 2 10
8.2 W
9
L1
VOUT
5V
to
6A
L2
18 SW1
C1
SW2
8
C2
15 DRVL 1
15 kW
13 kW
DRVL 2 11
14 VO1
51 kW
10 kW
VFB1
VFB2
4
1
CS1
CS2
5
PGOOD
7
PGOOD
EN2
6
EN 3.3 V
VREG3
3
VREG
(3.3-V LDO)
47 kW
0.1 µF
20 EN1
EN 5V
Charge-pump
Output
D1
VREG5
(5-V LDO)
13 VREG5
20 kW
1 µF
1 µF
0.1 µF
0.1 µF
Q2
2
19 VCLK
0.1 µF
VOUT
3.3 V
to
7A
UDG-12094
GND
Table 3. Key External Components (APPLICATION DIAGRAM (TPS51275/TPS51275C))
REFERENCE
DESIGNATOR
FUNCTION
MANUFACTURER
PART NUMBER
GLMC3R301A
L1
Output Inductor (5-VOUT)
Alps
L2
Output Inductor (3.3-VOUT)
Alps
GLMC2R201A
C1
Output Capacitor (5-VOUT)
SANYO
6TPE220MAZB x 2
C2
Output Capacitor (3.3-VOUT)
SANYO
6TPE220MAZB x 2
Q1
High-side MOSFET (5-VOUT)
TI
CSD87330Q3D
Q2
High-side MOSFET (3.3-VOUT)
TI
CSD87330Q3D
Copyright © 2012, Texas Instruments Incorporated
Submit Documentation Feedback
21
PACKAGE OPTION ADDENDUM
www.ti.com
23-Aug-2012
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package
Drawing
Pins
Package Qty
Eco Plan
(2)
Lead/
Ball Finish
MSL Peak Temp
(3)
TPS51275CRUKR
ACTIVE
WQFN
RUK
20
3000
Green (RoHS
& no Sb/Br)
CU NIPDAUAGLevel-2-260C-1 YEAR
TPS51275CRUKT
ACTIVE
WQFN
RUK
20
250
Green (RoHS
& no Sb/Br)
CU NIPDAUAGLevel-2-260C-1 YEAR
TPS51275RUKR
ACTIVE
WQFN
RUK
20
3000
Green (RoHS
& no Sb/Br)
CU NIPDAUAGLevel-2-260C-1 YEAR
TPS51275RUKT
ACTIVE
WQFN
RUK
20
250
Green (RoHS
& no Sb/Br)
CU NIPDAUAGLevel-2-260C-1 YEAR
Samples
(Requires Login)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
22-Aug-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
TPS51275CRUKR
WQFN
RUK
20
TPS51275CRUKT
WQFN
RUK
TPS51275RUKR
WQFN
RUK
TPS51275RUKT
WQFN
RUK
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
3000
330.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
20
250
180.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
20
3000
330.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
20
250
180.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
22-Aug-2012
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
TPS51275CRUKR
WQFN
RUK
20
3000
367.0
367.0
35.0
TPS51275CRUKT
WQFN
RUK
20
250
210.0
185.0
35.0
TPS51275RUKR
WQFN
RUK
20
3000
367.0
367.0
35.0
TPS51275RUKT
WQFN
RUK
20
250
210.0
185.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All
semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time
of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Mobile Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated