LED15W LED15W SERIES DC-DC CONVERTER 4:1 ULTRA WIDE INPUT RANGE UP TO 15Watts FEATURES APPLICATIONS • NO MINIMUM LOAD REQUIRED • 2250VDC INPUT TO OUTPUT ISOLATION • SMALL SIZE AND LOW PROFILE 1.10 x 0.94 x 0.34 INCH • SURFACE-MOUNT OR THROUGH-HOLE • UL60950-1, EN60950-1, & IEC60950-1 SAFETY APPROVALS • CE MARKED • COMPLIANT TO RoHS II & REACH • WIRELESS NETWORK • TELECOM/DATACOM • INDUSTRY CONTROL SYSTEM • DISTRIBUTED POWER ARCHITECTURES • SEMICONDUCTOR EQUIPMENT ： 2250VDC ISOLATION REMOTE CONTROL UVP OCP SCP OVP TECHNICAL SPECIFICATION All specifications are typical at nominal input, full load and 25℃ otherwise noted Model Number LED15-24S3P3W LED15-24S05W LED15-24S12W LED15-24S15W LED15-48S3P3W LED15-48S05W LED15-48S12W LED15-48S15W Input Range Output Voltage Output Current @Full Load Input Current @ No Load Efficiency Maximum Capacitor Load (1) VDC 9 ~ 36 9 ~ 36 9 ~ 36 9 ~ 36 18 ~ 75 18 ~ 75 18 ~ 75 18 ~ 75 VDC 3.3 5 12 15 3.3 5 12 15 mA 4000 3000 1300 1000 4000 3000 1300 1000 mA 60 70 10 10 40 40 10 10 % 85 87 86 86 85 87 86 86 µF 12000 6000 1000 660 12000 6000 1000 660 PART NUMBER STRUCTURE LED15 Series Name 1 48 Input Voltage (VDC) 24: 9~36 48: 18~75 S Output Quantity S: Single 05 Output Voltage (VDC) 3P3: 3.3 05: 5 12: 12 15: 15 W - A Input Range 4:1 Option : A: B: C: D: E: F: G: H: I: J: K: www.PDUKE.com Negative logic remote ON/OFF with DIP(Standard) Negative logic remote ON/OFF with SMT Positive logic remote ON/OFF with DIP Positive logic remote ON/OFF with SMT DIP type without Ctrl pin SMT type without Ctrl pin DIP type, negative logic remote ON/OFF without Trim pin SMT type, negative logic remote ON/OFF without Trim pin DIP type without Ctrl & Trim pin SMT type without Ctrl & Trim pin DIP type, positive logic remote ON/OFF without Trim pin SMT type, positive logic remote ON/OFF without Trim pin 2014/04/30 LED15W INPUT SPECIFICATIONS Parameter Conditions 24Vin(nom) 48Vin(nom) Operating input voltage range Input reflected ripple current Start-up voltage Start up time Constant resistive load Input surge voltage 100ms, max. Remote ON/OFF Referred to –Vin pin OUTPUT SPECIFICATIONS Parameter Over load protection Short circuit protection 24Vin(nom) 48Vin(nom) 24Vin(nom) 48Vin(nom) Power up Remote ON/OFF 24Vin(nom) 48Vin(nom) Positive logic DC-DC ON (Option) DC-DC OFF Negative logic DC-DC ON (Standard) DC-DC OFF Input current of Ctrl pin Remote off input current Conditions Max. Unit 24 48 30 36 75 VDC mAp-p 9 18 -0.5 VDC 30 30 50 100 Open or 3 ~ 15VDC Short or 0 ~ 1.2VDC Short or 0 ~ 1.2VDC Open or 3 ~ 15VDC 1.0 2.5 Typ. -1.0 -0.2 -0.2 -10 Measured by 20MHz bandwidth, With a 1µF M/C X7R and a 10µF T/C 25% load step change % of Iout rated; Hiccup mode % % % % mVp-p %/ µs 5.4 7.0 17.5 20.5 Conditions Min. Input to Output Typ. Max. 2250 1 3.3Vout, 5Vout 12Vout, 15Vout 315 360 350 400 1500 385 440 Conditions Operating ambient temperature Storage temperature range Thermal shock Vibration Relative humidity Lead-free reflow solder process Unit VDC GΩ pF kHz -40 -55 Typ. Max. Unit ℃ ℃ +120 +125 MIL-STD-810F MIL-STD-810F 5% to 95% RH IPC J-STD-020D IPC J-STD-033B level 2a EMC SPECIFICATIONS Parameter 2 Min. With derating Moisture sensitivity level(MSL) EMI (3) Radiated immunity Fast transient (4) Surge (4) Conducted immunity VDC UL60950-1 EN60950-1 IEC60950-1 10.5g (0.36oz) 2.444 x 106 hrs MIL-HDBK-217F, Full load ENVIRONMENTAL SPECIFICATIONS Parameter ℃ 150 % Continuous, automatics recovery Safety approvals Weight MTBF mA mA Unit +0.02 3.7 5.6 13.8 16.8 VDC +1.0 +0.2 +0.2 +10 250 3.3Vout 5Vout 12Vout 15Vout ms Max. 100 -0.02 1 minute 500VDC VDC 8 16 Min. Low Line to High Line at Full Load No Load to Full Load GENERAL SPECIFICATIONS Parameter Isolation voltage Isolation resistance Isolation capacitance Switching frequency Typ. 9 18 Nominal input and Full load Shutdown voltage Voltage accuracy Line regulation Load regulation Voltage adjustability (2) Ripple and noise Temperature coefficient Transient response recovery time Over voltage protection Min. Conditions EN55022 EN61000-4-3 EN61000-4-4 EN61000-4-5 EN61000-4-6 10 V/m ± 2kV ± 1kV 3 Vr.m.s www.PDUKE.com Level Class A, Class B Perf. Criteria A Perf. Criteria A Perf. Criteria A Perf. Criteria A 2014/04/30 LED15W Note: 1. 2. 3. 4. Test by minimum input and constant resistive load. Trimming allows the user to increase or decrease the output voltage set point of the module. This is accomplished by connecting an external resistor between the TRIM pin and either +Vout pin or -Vout pin. The standard modules meet EN55022 Class A and Class B with external components. For further information, please contact with P-DUKE. An external input filter capacitor is required if the module has to meet EN61000-4-4, EN61000-4-5. The filter capacitor Power Mate suggest: Nippon chemi-con KY series, 220µF/100V. CAUTION: This power module is not internally fused. An input line fuse must always be used. CHARACTERISTIC CURVE LED15-48S05W Derating Curve LED15-48S05W Efficiency vs. Input Voltage LED15-48S05W Efficiency vs. Output Load MECHANICAL DRAWING DIP TYPE PIN CONNECTION PIN 1 2 3 4 5 6 DEFINE +Vin -Vin Ctrl +Vout Trim -Vout EXTERNAL OUTPUT TRIMMING Output can be externally trimmed by using the method shown below. TRIM UP TRIM DOWN 6 5 RU 5 RD 4 SMT TYPE 1. All dimensions in inch (mm) 2. Tolerance :x.xx±0.02 (x.x±0.5) x.xxx±0.01 (x.xx±0.25) 3. Pin pitch tolerance ±0.01 (0.25) 4. Pin dimension tolerance ±0.004(0.1) 3 www.PDUKE.com 2014/04/30