SPRING-LOADED CONNECTORS PAD CONNECTORS TEL +41 32 421 04 00 GENERAL SPECIFICATIONS [email protected] The values listed below are general specs applying for Preci-Dip spring-loaded connectors. Please see individual catalog page for additional and product specific technical data. OPERATING TEMPERATURE RANGE CLIMATIC CATEGORY (IEC) OPERATING HUMIDIT Y RANGE MA X. WORKING VOLTAGE UL ® -55 ... +125 °C 55/85/21 Annual mean 75% 100 VRMS /150 VDC (2.54 mm grid) Preci-Dip products are recognized by Underwriters Laboratories Inc. and listed under “Connectors for Use in Data, Signal, Control and Power Applications“, File Nr. E174442. PACKAGING MECHANICAL CHARACTERISTICS MIN. INITIAL HEIGHT STROKE/HEIGHT RATIO MA X STROKE MIN. INITIAL SPRING FORCE BASIC LOW RESISTANCE LOW RESISTANCE HOLLOW PISTON T YPE SHAPED PISTON T YPE CLIP IN-LINE DESIGN T YPE 3 mm Max. 0.3 2 mm 0.2 N 6 mm Max. 0.2 2 mm 0.2 N 10 mm Max. 0.15 1.5 mm 0.2 N • Standard connector packaging is card box. • SMD mount connectors available on request with Tape & Reel packaging acc. to EIA Standard 481. These products are marked with the symbol: T & R Packaging ELECTRICAL CHARACTERISTICS INSUL ATION RESISTANCE BETWEEN ANY TWO ADJACENT CONTACTS CAPACITANCE BETWEEN ANY TWO ADJACENT CONTACTS Min. 10’000 MΩ at 500 VAC Max. 1 pF Please consult www.precidip.com for availability, size of tape, size of reel, number of components per reel and packing units. ENVIRONMENTAL CHARACTERISTICS The sockets withstand the following environmental tests without mechanical and electrical defects: • Dry heat steady state IEC 60512-11-9.11i / 60068-2-2.Bb: 125 °C, 16 h • Damp heat cyclic IEC 60512-11-12.11m / 60068-2-30.Db: 25/55 °C, 90 – 100 %rH, 1 cycle of 24 h • Cold steady state IEC 60512-11-10.11j / 60068-2-1.A: -55 °C, 2 h • Thermal shock IEC 60512-11-4.11d / 60068-2-14.Na: -55/125 °C, 5 cycles 30 min • Sinusoidal vibrations IEC 60512-6-4.6d / 60068-2-6.Fc: 10 to 500 Hz, 10 g, 1 octave/min, 10 cycles for each axis • Shock IEC 60512-6-3.6c / 60068-2-27.Ea: 50 g, 11 ms, 3 shocks in three axis During the above two tests, no contact interruption >50 ns does appear. • Solderability J-STD-002A, Test A, 245 °C, 5 s, solder alloy SnAg3.8Cu0.7 • Resistance to soldering heat J-STD-020C, 260 °C, 20 s • Moisture sensitivity J-STD-020C level 1 • Resistance to corrosion: 1) Salt spray test IEC 60068-2-11.Ka: 48 h 2) Sulfur dioxide (SO2) test IEC 60068-2-42 Kc: 96 h at 25 ppm SO2, 25 °C, 75 %rH 3) Hydrogen sulfide (H2S) test IEC 60068-2-43 Kd: 96 h at 12 ppm H2S, 25 °C, 75 %rH Due to technical progress, all information provided is subject to change without prior notice. 31 SPRING–LOADED CONNECTORS WWW.PRECIDIP.COM