TECH. CORP. SPECIFICATIONS CUSTOMER : CTW197 SAMPLE CODE : SG16032WRS-BWH-H-Q MASS PRODUCTION CODE : PG16032WRS-BWH-H-Q SAMPLE VERSION : 01 SPECIFICATIONS EDITION : 002 DRAWING NO. (Ver.) : HLMD-PG16032WRS-BWH-H-Q (Ver.002) PACKAGING NO. (Ver.) : HPKG-PG16032WRS-BWH-H-Q (Ver.001) Customer Approved Date: Approved Checked 王剛/張慶源 詹漢華 □ Preliminary specification for design input ■ Specification for sample approval Designer 李遠東/李貴忠 POWERTIP TECH. CORP. Headquarters: E-mail: [email protected] th No.8, 6 Road, Taichung Industrial Park, TEL: 886-4-2355-8168 Taichung, Taiwan Http://www.powertip.com.tw FAX: 886-4-2355-8166 台中市 407 工業區六路 8 號 NO.PT-A-005-8 RECORDS OF REVISION Date Ver. Edi. Description 11/27/2008 01 001 The drawing has changed the B/L base on powertip mass production:PG16032ORS-BWH-B-Q 楊興華 3/05/2009 01 002 New Sample 李遠東 (mm / dd / yyyy) Page Design by Total: 32page PG16032WRS-BWH-H-Q (DK) Page2 SAMPLE Ver.01 SPEC Edi.002 Contents 1. SPECIFICATIONS 1.1 Features 1.2 Mechanical Specifications 1.3 Absolute Maximum Ratings 1.4 DC Electrical Characteristics 1.5 Optical Characteristics 1.6 Backlight Characteristics 2. MODULE STRUCTURE 2.1 Counter Drawing 2.2 Interface Pin Description 2.3 Timing Characteristics 2.4 Display Command 2.5 Function Description 2.6 JUMPER 3. QUALITY ASSURANCE SYSTEM 3.1 Quality Assurance Flow Chart 3.2 Inspection Specification 4. RELIABILITY TEST 4.1 Reliability Test Condition 5. PRECAUTION RELATING PRODUCT HANDLING 5.1 Safety 5.2 Handling 5.3 Storage 5.4 Terms of Warranty Appendix: 1. LCM Drawing 2. Packing Specification PG16032WRS-BWH-H-Q (DK) Page3 SAMPLE Ver.01 SPEC Edi.002 1. SPECIFICATIONS 1.1 Features Item Standard Value Display Type 160*32 Dots LCD Type STN Gray, Positive, Transflective, Extended Temp Driver Condition LCD Module : 1/32 Duty,1/5.6Bias Viewing Direction 6 O’clock Backlight White LED B/L Weight 42.5g Interface 8 bit parrallel Other(controller / driver IC) ST7920-0B ,ST7921 ROHS THIS PRODUCT CONFORMS THE ROHS OF PTC Detail information please refer web side : http://www.powertip.com.tw/news/LatestNews.asp 1.2 Mechanical Specifications Item Standard Value Unit Outline Dimension 101.0 (L)*35.0(W)*13.1 (H) mm Viewing Area 64.5 (L)*17.2 (W) mm Active Area 59.17 (L)*15.01 (W) mm Dot Size 0.34 (L)*0.44 (W) mm Dot Pitch 0.37 (L)*0.47 (W) mm Note：For detailed information please refer to LCM drawing 1.3 Absolute Maximum Ratings Item Symbol Condition Min. Max. Unit Power Supply Voltage VDD － -0.3 5.5 V LCD Driver Supply Voltage VLCD － -0.3 7.0 V Input Voltage VIN － -0.3 VDD+0.3 V Operating Temperature TOP － -20 70 ℃ Storage Temperature TST － -30 80 ℃ Storage Humidity HD Ta＜60 ℃ - 90 %RH PG16032WRS-BWH-H-Q (DK) Page4 SAMPLE Ver.01 SPEC Edi.002 1.4 DC Electrical Characteristics VDD=5.0V±10% ,VSS=0V ,Ta = 25℃ Item Symbol Condition Min. Typ. Max. Unit Logic Supply Voltage VDD - 4.5 5.0 5.5 V “H” Input Voltage VIH - 0.7VDD - VDD V “L” Input Voltage VIL - -0.3 - 0.6 V “H” Output Voltage VOH IOH=-0.1mA 0.8VDD - VDD V “L” Output Voltage VOL IOL=0.1mA - - 0.4 V VDD=5.0V;VOP= 5.5 V; Pattern= Full display - 1.2 - VDD=5.0V;VOP= 5.5 V; Pattern= Perpendicular line*1 - 1.4 3.0 -20℃ 5.6 5.8 6.0 25℃ 5.3 5.5 5.7 70℃ 5.0 5.2 5.4 Supply Current LCM Driver Voltage IDD VOP*2 mA V NOTE: *1 The Maximum current display; *2 The VOP test point is VDD-VO. PG16032WRS-BWH-H-Q (DK) Page5 SAMPLE Ver.01 SPEC Edi.002 1.5 Optical Characteristics LCD Panel：1/32Duty，1/5.6Bias，VLCD =6.6V，Ta =25℃ Item Symbol Min. Typ. Max. Rise tr - 150 225 Fall tf - 200 300 Top ΘY+ C>2.0, - - 40 Bottom ΘY- ∅ =270° - - 40 Left ΘX- - - 45 Right ΘX+ - - 45 2 3 - 15 20 - 0.26 0.314 0.36 Y 0.26 0.316 0.36 △B 70 - - Response Time Viewing angle range Conditions Contrast Ratio C Average Brightness (with LCD) *2 IV CIE Color Coordinate X (With LCD) *2 Uniformity *1 θ = 0°, ∅ = 270° IF=40mA Unit Reference ms Note2 Deg. Notes 1 Note 3 cd/m2 Note 4 % Note 4 : 1：△B=B(min) / B(max) * 100% 2：Measurement Condition for Optical Characteristics: a：Environment: 25℃±5℃ / 60±20%R.H，no wind，dark room below 10 Lux at typical lamp current and typical operating frequency. b：Measurement Distance: 500 ± 50 ㎜ ，(θ= 0°) c：Equipment: TOPCON BM-7 fast，(field 1°)，after 10 minutes operation. d：The uncertainty of the C.I.E coordinate measurement ±0.01，Average Brightness ± 4% 1 2 3 VIEW AREA 6 5 4 7 8 θθ 9 500 ㎜ LCM Colorimeter=BM-7 fast PG16032WRS-BWH-H-Q (DK) Page6 SAMPLE Ver.01 SPEC Edi.002 Note 1. Optical characteristics-2 Viewing angle Rear (12H) φ=90° Top (θ=0°) θL θR θ+ θ- Left (9H) φ=180° Right (3H) φ=0° Front (6H) φ=270° Viewing angle PG16032WRS-BWH-H-Q (DK) Page7 SAMPLE Ver.01 SPEC Edi.002 Note 2. Optical characteristics-3 Fig.2 Definition of response time Positive Type No selected waveform No selected waveform Selected waveform Transmittance 10% 90% 100% Tf Tr Negative Type No selected waveform No selected Selected waveform Transmittance 100% 90% 10% Tr PG16032WRS-BWH-H-Q (DK) Tf Page8 SAMPLE Ver.01 SPEC Edi.002 Electrical characteristics-2 ※2 Drive waveform Vop: Drive voltage 1/B: Bias N: Duty fF: Frame frequency fD: Drive frequency (1) Selected waveform 1 2 3 N 1 3 2 V Vop/B Vop/B V 1/fD 1/fF (2) Non- Selected wave form 1 2 3 N 1 2 3 (1-2/B)Vop Vop/B Vop/ (1-2/B)Vop 1/fF 1/fD Note: Frame frequency is defined as follows: Common side supply voltage peak - to - peak /2 = 1 period PG16032WRS-BWH-H-Q (DK) Page9 SAMPLE Ver.01 SPEC Edi.002 Note 3. : Definition of Vth Selected waveform 100 73% Transmittanc No selected waveform 50% Vth2 Vth1 Drive Active voltage range View direction Drive waveform Transmittance Vth1 10° (Selected waveform) 50% Vth2 40° (No selected waveform) 73% ※1 Contrast ratio = (Brightness in OFF state) / (Brightness in ON state) Outline of Electro-Optical Characteristics Measuring System Photo Detector θ Human Active Temperatur e Control Chamber ψ LCD Panel Transmissive Measuring System: Autronic DMS-803 PG16032WRS-BWH-H-Q (DK) Page10 SAMPLE Ver.01 SPEC Edi.002 1.6 Backlight Characteristics LCD Module with LED Backlight Maximum Ratings Item Symbol Conditions Min. Max. Unit Forward Current IF Ta =25℃ - 70 mA Reverse Voltage VR Ta =25℃ - 5 V Reverse Current IR VR=5V - 0.1 uA Power Dissipation PD Ta =25℃ - 0.32 W Item Symbol Conditions Min. Typ. Max. Unit Forward Voltage VF 2.7 3.6 4.5 V Average Brightness (without LCD) IV 120 - - cd/m2 CIE Color Coordinate x 0.26 0.31 0.35 - (without LCD) Y 0.26 0.31 0.35 - Electrical / Optical Characteristics IF= 40mA Color PG16032WRS-BWH-H-Q (DK) WHITE Page11 SAMPLE Ver.01 SPEC Edi.002 2. MODULE STRUCTURE 2.1 CounterDrawing 2.1.1 LCM Mechanical Diagram * See Appendix 2.1.2 Block Diagram Vo E PG16032WRS-BWH-H-Q (DK) Page12 SAMPLE Ver.01 SPEC Edi.002 2.2 Interface Pin Description Pin No. Symbol 1 VSS Power Supply (Vss=0) 2 VDD Power Supply (VDD>VSS) 3 VO Operating voltage for LCD RS Register Selection input High = Data register Low = Instruction register (for write) Busy flag address counter (for read) 4 5 Signal Description Read/Write signal input is used to select the read/write mode High = Read mode, Low = Write mode R/W 6 E Start enable signal to read or write the data 7 DB0 Four low order bi-directional three-state data bus lines. Use 8 DB1 9 DB2 for data transfer between the MPU and the LCD module. These four are not used during 4-bit operation. 10 DB3 11 DB4 12 DB5 13 DB6 14 DB7 15 A Power supply LED backlight (+) 16 K Power supply LED backlight (-) Four high order bi-directional three-state data bus lines. Used for data transfer between the MPU and the LCD module. DB7 can be used as a busy flag. Contrast Adjust VDD 2 VO 10~20KΩ 3 LCD MODULE 15 Negative Voltage 16 3.6 V PG16032WRS-BWH-H-Q (DK) Page13 SAMPLE Ver.01 SPEC Edi.002 2.3 Timing Characteristics ● Writing data from MPU to ST7920 ●Reading data from ST7920 to MPU PG16032WRS-BWH-H-Q (DK) Page14 SAMPLE Ver.01 SPEC Edi.002 • Write Mode (Writing data from MPU to ST7920) (VDD= +5V+10%,Ta=25°C) Symbol Characteristics Test Condition Min. Typ. Max. Unit TC Enable Cycle Time Pin E 1200 - - ns TPW Enable Pulse Width Pin E 140 - - ns - - 25 ns TR , TF Enable Rise / Fall Time Pin E TAS Address Setup Time Pins: RS , RW,E 10 - - ns TAH Address Hold Time Pins :RS,RW,E 20 - - ns Pins:DB0~DB7 40 - - ns Pins:DB0~DB7 20 - - ns TDSW Data Setup Time TH Data Hold Time • Read Mode (Reading data from ST7920 to MPU) (VDD= +5V+10%,Ta=25°C) Symbol Characteristics Test Condition Min. Typ. Max. Unit TC Enable Cycle Time Pin E 1200 - - ns TPW Enable Pulse Width Pin E 140 - - ns - - 25 ns TR , TF Enable Rise / Fall Time Pin E TAS Address Setup Time Pins: RS , RW,E 10 - - ns TAH Address Hold Time Pins :RS,RW,E 20 - - ns Pins:DB0~DB7 - - 100 ns Pins:DB0~DB7 20 - - ns TDDR Data Setup Time TH Data Hold Time PG16032WRS-BWH-H-Q (DK) Page15 SAMPLE Ver.01 SPEC Edi.002 2.4 Display Command PG16032WRS-BWH-H-Q (DK) Page16 SAMPLE Ver.01 SPEC Edi.002 PG16032WRS-BWH-H-Q (DK) Page17 SAMPLE Ver.01 SPEC Edi.002 PG16032WRS-BWH-H-Q (DK) Page18 SAMPLE Ver.01 SPEC Edi.002 2.5 Function Description PG16032WRS-BWH-H-Q (DK) Page19 SAMPLE Ver.01 SPEC Edi.002 PG16032WRS-BWH-H-Q (DK) Page20 SAMPLE Ver.01 SPEC Edi.002 PG16032WRS-BWH-H-Q (DK) Page21 SAMPLE Ver.01 SPEC Edi.002 2.6 JUMPER(Setting different use) 2.6.1 SHORT :: J2/J4(3.2)/J5(3.1)J3(3.2)/JF 2.6.2 OPEN : All the jumpers unnoted PG16032WRS-BWH-H-Q (DK) Page22 SAMPLE Ver.01 SPEC Edi.002 3. QUALITY ASSURANCE SYSTEM 3.1 Quality Assurance Flow Chart Item Customer Sales Info Marketing & Design R&D Manufactur ing Q.A Product control Purchase Inventory control Survey Request Project Inquiry evaluation Project Validation NG OK Quote Contract Design check Sample test Sample Approval NG Verification NG OK Sample approval OK Pilot NG Pilot Run & Mass Product run & Reliability test Verification OK Specification preparation Mass production OK Inspection NG Shipment Ship out Ship Out PG16032WRS-BWH-H-Q (DK) Page23 SAMPLE Ver.01 SPEC Edi.002 Item Customer Sales Info Claim R&D Q.A Manufactu ring Product control Purchase Inventory control Failure analysis Sales Service Analysis report Corrective action Tracking 1. ISO 9001 Maintenance Activities Q.A 3. Equipment calibration Activity 5. Standardization Management PG16032WRS-BWH-H-Q (DK) 2. Process improvement proposal 4. Education And Training Activities Page24 SAMPLE Ver.01 SPEC Edi.002 3.2 Inspection Specification PG16032WRS-BWH-H-Q (DK) Page25 SAMPLE Ver.01 SPEC Edi.002 PG16032WRS-BWH-H-Q (DK) Page26 SAMPLE Ver.01 SPEC Edi.002 PG16032WRS-BWH-H-Q (DK) Page27 SAMPLE Ver.01 SPEC Edi.002 PG16032WRS-BWH-H-Q (DK) Page28 SAMPLE Ver.01 SPEC Edi.002 PG16032WRS-BWH-H-Q (DK) Page29 SAMPLE Ver.01 SPEC Edi.002 PG16032WRS-BWH-H-Q (DK) Page30 SAMPLE Ver.01 SPEC Edi.002 4. RELIABILITY TEST 4.1 Reliability Test Condition NO. 1 2 3 4 TEST ITEM TEST CONDITION High Temperature Storage Test Keep in 80 ±2℃ 96 hrs Surrounding temperature, then storage at normal condition 4hrs Low Temperature Storage Test Keep in -30 ±2℃ 96 hrs Surrounding temperature, then storage at normal condition 4hrs Keep in +60℃/90%RH duration for 96 hrs High Humidity Storage Surrounding temperature, then storage at normal condition 4hrs Air Discharge: Contact Discharge: Apply 6 KV with 5 times Apply 250V with 5 times Discharge for each polarity +/discharge for each polarity +/1. Temperature Ambient:15℃～35℃ 2. Humidity relative:30%～60% 3. Energy Storage Capacitance(Cs+Cd):150pF±10% ESD Test 4. Discharge Resistance(Rd):330Ω±10% 5. Discharge, mode of operation: Single Discharge (time between successive discharges at least 1 s) (Tolerance lf the output voltage indication: ±5%) -20℃ → 25℃ → 70℃ → 25℃ 5 Temperature Cycling Test 6 Vibration Test (Packaged) (30mins) (5mins) (30mins) (5mins) 10 Cycle Surrounding temperature, then storage at normal condition 4hrs 1. Sine wave 10～55HZ frequency (1 min) 2. The amplitude of vibration :1.5 mm 3. Each direction (XYZ) duration for 2 Hrs Packing Weight (Kg) 0 ~ 45.4 7 Drop Test (Packaged) Drop Height (cm) 122 45.4 ~ 90.8 76 90.8 ~ 454 61 Over 454 46 Drop direction :※3 comer /1 edges /6 sides etch 1times PG16032WRS-BWH-H-Q (DK) Page31 SAMPLE Ver.01 SPEC Edi.002 5. PRECAUTION RELATING PRODUCT HANDLING 5.1 SAFETY 5.1.1 5.1.2 If the LCD panel breaks , be careful not to get the liquid crystal to touch your skin. If the liquid crystal touches your skin or clothes , please wash it off immediately by using soap and water. 5.2 HANDLING 5.2.1 5.2.2 5.2.3 5.2.4 5.2.5 5.2.6 5.2.7 5.2.8 5.2.9 Avoid any strong mechanical shock which can break the glass. Avoid static electricity which can damage the CMOS LSI—When working with the module , be sure to ground your body and any electrical equipment you may be using. Do not remove the panel or frame from the module. The polarizing plate of the display is very fragile. So , please handle it very carefully ,do not touch , push or rub the exposed polarizing with anything harder than an HB pencil lead (glass , tweezers , etc.) Do not wipe the polarizing plate with a dry cloth , as it may easily scratch the surface of plate. Do not touch the display area with bare hands , this will stain the display area. Do not use ketonics solvent & aromatic solvent. Use with a soft cloth soaked with a cleaning naphtha solvent. To control temperature and time of soldering is 320±10℃and 3-5 sec. To avoid liquid (include organic solvent) stained on LCM . 5.3 STORAGE 5.3.1 5.3.2 5.3.3 Store the panel or module in a dark place where the temperature is 25℃ ±5℃ and the humidity is below 65% RH. Do not place the module near organics solvents or corrosive gases. Do not crush , shake , or jolt the module. 5.4 TERMS OF WARRANTY 5.4.1 5.4.2 Applicable warrant period The period is within thirteen months since the date of shipping out under normal using and storage conditions. Unaccepted responsibility This product has been manufactured to your company’s specification as a part for use in your company’s general electronic products. It is guaranteed to perform according to delivery specifications. For any other use apart from general electronic equipment , we cannot take responsibility if the product is used in nuclear power control equipment , aerospace equipment , fire and security systems or any other applications in which there is a direct risk to human life and where extremely high levels of reliability are required. PG16032WRS-BWH-H-Q (DK) Page32 SAMPLE Ver.01 SPEC Edi.002