IDT IDT74LVC823APG

IDT74LVC823A
3.3V CMOS 9-BIT BUS-INTERFACE FLIP-FLOP
INDUSTRIAL TEMPERATURE RANGE
3.3V CMOS 9-BIT
BUS-INTERFACE FLIP-FLOP
WITH 3-STATE OUTPUTS
AND 5 VOLT TOLERANT I/O
IDT74LVC823A
DESCRIPTION:
FEATURES:
The LVC823A 9-bit bus-interface flip-flop is built using advanced dual
metal CMOS technology. The LVC823A device is designed specifically for
driving highly capacitive or relatively low-impedance loads. The device is
particularly suitable for implementing wider buffer registers, I/O ports,
bidirectional bus drivers with parity, and working registers.
With the clock-enable (CLKEN) input low, the nine D-type edge-triggered
flip-flops enter data on the low-to-high transitions of the clock. Taking CLKEN
high disables the clock buffer, latching the outputs. This device has
noninverting data (D) inputs. Taking the clear (CLR) input low causes the
nine Q outputs to go low, independently of the clock.
A buffered output-enable (OE) input can be used to place the nine outputs
in either a normal logic state (high or low logic levels) or a high-impedance
state. OE does not affect internal operations of the latch. Previously stored
data can be retained or new data can be entered while the outputs are in
the high-impedance state.
The LVC823A has been designed with a ±24mA output driver. This
driver is capable of driving a moderate to heavy load while maintaining
speed performance.
To ensure the high-impedance state during power up or power down,
OE should be tied to VCC through a pullup resistor; the minimum value of
the resistor is determined by the current-sinking capability of the driver.
Inputs can be driven from either 3.3V or 5V devices. This feature allows
the use of this device as a translator in a mixed 3.3V/5V system environment.
• 0.5 MICRON CMOS Technology
• ESD > 2000V per MIL-STD-883, Method 3015; > 200V using
machine model (C = 200pF, R = 0)
• VCC = 3.3V ± 0.3V, Normal Range
• VCC = 2.7V to 3.6V, Extended Range
µ W typ. static)
• CMOS power levels (0.4µ
• Rail-to-rail output swing for increased noise margin
• All inputs, outputs, and I/O are 5V tolerant
• Supports hot insertion
• Available in SSOP, QSOP, and TSSOP packages
DRIVE FEATURES:
• High Output Drivers: ±24mA
• Reduced system switching noise
APPLICATIONS:
• 3.3V high speed systems
• 3.3V and lower voltage computing systems
FUNCTIONAL BLOCK DIAGRAM
OE
CLR
CLKEN
CLK
1D
1
11
14
R
13
C1
2
23
1Q
1D
TO EIGHT OTHER CHANNELS
The IDT logo is a registered trademark of Integrated Device Technology, Inc.
INDUSTRIAL TEMPERATURE RANGE
JANUARY 2004
1
©
2004 Integrated Device Technology, Inc.
DSC-4608/2
IDT74LVC823A
3.3V CMOS 9-BIT BUS-INTERFACE FLIP-FLOP
INDUSTRIAL TEMPERATURE RANGE
PIN CONFIGURATION
ABSOLUTE MAXIMUM RATINGS(1)
Symbol
1
24
VCC
2
23
1Q
2D
3
22
2Q
3D
4
21
3Q
4D
5
20
4Q
5D
6
19
5Q
6D
7
18
6Q
7D
8
17
7Q
8D
9
16
8Q
OE
1D
9D
10
15
9Q
CLR
11
14
CLKEN
GND
12
13
CLK
Description
Max
Unit
VTERM
Terminal Voltage with Respect to GND
–0.5 to +6.5
V
TSTG
Storage Temperature
–65 to +150
°C
IOUT
DC Output Current
–50 to +50
mA
IIK
IOK
Continuous Clamp Current,
VI < 0 or VO < 0
–50
mA
ICC
ISS
Continuous Current through each
VCC or GND
±100
mA
NOTE:
1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause
permanent damage to the device. This is a stress rating only and functional operation
of the device at these or any other conditions above those indicated in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect reliability.
CAPACITANCE (TA = +25°C, F = 1.0MHz)
Parameter(1)
Symbol
Conditions
Typ.
Max.
Unit
CIN
Input Capacitance
VIN = 0V
4.5
6
pF
COUT
Output Capacitance
VOUT = 0V
5.5
8
pF
CI/O
I/O Port Capacitance
VIN = 0V
6.5
8
pF
NOTE:
1. As applicable to the device type.
PIN DESCRIPTION
Pin Names
SSOP/ QSOP/ TSSOP
TOP VIEW
Description
Output Enable Input (Active LOW)
OE
CLK
Clock Input
Clock Enable Input (Active LOW)
CLKEN
CLR
Clear Input (Active LOW)
xD
Data Inputs
xQ
Data Outputs
FUNCTION TABLE (EACH FLIP-FLOP)(1)
Inputs
Outputs
OE
CLR
CLKEN
CLK
xD
xQ
L
L
X
X
X
L
L
H
L
↑
H
H
L
H
L
↑
L
L
L
H
H
X
X
Q(2)
H
X
X
X
X
Z
NOTES:
1. H = HIGH Voltage Level
L = LOW Voltage Level
X = Don’t Care
Z = High Impedance
↑ = LOW-to-HIGH transition
2. Output level before indicated steady-state input conditions were established.
2
IDT74LVC823A
3.3V CMOS 9-BIT BUS-INTERFACE FLIP-FLOP
INDUSTRIAL TEMPERATURE RANGE
DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE
Following Conditions Apply Unless Otherwise Specified:
Operating Condition: TA = –40°C to +85°C
Symbol
VIH
VIL
Min.
Typ.(1)
Max.
Unit
VCC = 2.3V to 2.7V
1.7
—
—
V
VCC = 2.7V to 3.6V
2
—
—
VCC = 2.3V to 2.7V
—
—
0.7
VCC = 2.7V to 3.6V
—
—
0.8
Parameter
Input HIGH Voltage Level
Input LOW Voltage Level
Test Conditions
V
Input Leakage Current
VCC = 3.6V
VI = 0 to 5.5V
—
—
±5
µA
IOZH
High Impedance Output Current
VCC = 3.6V
VO = 0 to 5.5V
—
—
±10
µA
IOZL
(3-State Output pins)
IOFF
Input/Output Power Off Leakage
VCC = 0V, VIN or VO ≤ 5.5V
—
—
±50
µA
VIK
Clamp Diode Voltage
VCC = 2.3V, IIN = –18mA
—
–0.7
–1.2
V
VH
ICCL
ICCH
ICCZ
∆ICC
Input Hysteresis
Quiescent Power Supply Current
VCC = 3.3V
VCC = 3.6V
VIN = GND or VCC
—
—
100
—
—
10
mV
µA
3.6 ≤ VIN ≤ 5.5V(2)
One input at VCC - 0.6V, other inputs at VCC or GND
—
—
—
—
10
500
µA
IIH
IIL
Quiescent Power Supply Current
Variation
NOTES:
1. Typical values are at VCC = 3.3V, +25°C ambient.
2. This applies in the disabled state only.
OUTPUT DRIVE CHARACTERISTICS
Symbol
VOH
VOL
Test Conditions(1)
Parameter
Output HIGH Voltage
Output LOW Voltage
Min.
Max.
Unit
V
VCC = 2.3V to 3.6V
IOH = – 0.1mA
VCC – 0.2
—
VCC = 2.3V
IOH = – 6mA
2
—
VCC = 2.3V
IOH = – 12mA
1.7
—
VCC = 2.7V
2.2
—
VCC = 3V
2.4
—
VCC = 3V
IOH = – 24mA
2.2
—
VCC = 2.3V to 3.6V
IOL = 0.1mA
—
0.2
VCC = 2.3V
IOL = 6mA
—
0.4
IOL = 12mA
—
0.7
VCC = 2.7V
IOL = 12mA
—
0.4
VCC = 3V
IOL = 24mA
—
0.55
V
NOTE:
1. VIH and VIL must be within the min. or max. range shown in the DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE table for the appropriate VCC range.
TA = – 40°C to + 85°C.
3
IDT74LVC823A
3.3V CMOS 9-BIT BUS-INTERFACE FLIP-FLOP
INDUSTRIAL TEMPERATURE RANGE
OPERATING CHARACTERISTICS, VCC = 3.3V ± 0.3V, TA = 25°C
Symbol
Parameter
CPD
Power Dissipation Capacitance per Flip-Flop Outputs enabled
CPD
Power Dissipation Capacitance per Flip-Flop Outputs disabled
Test Conditions
Typical
Unit
CL = 0pF, f = 10Mhz
59
pF
46
SWITCHING CHARACTERISTICS(1)
VCC = 2.7V
Symbol
fMAX
Parameter
tPLH
Propagation Delay
tPHL
CLK to xQ
tPHL
Propagation Delay
VCC = 3.3V ± 0.3V
Min.
150
Max.
—
Min.
150
Max.
—
Unit
MHz
—
8.9
1.4
8
ns
—
8.8
2.5
7.9
ns
—
8.3
1.6
7.2
ns
—
7.1
1.1
6
ns
CLR to xQ
tPZH
Output Enable Time
tPZL
OE to xQ
tPHZ
Output Disable Time
tPLZ
OE to xQ
tW
Pulse Duration, CLR LOW
3.3
—
3.3
—
ns
tW
Pulse Duration, CLK HIGH or LOW
3.3
—
3.3
—
ns
tSU
Set-up Time, CLR inactive before CLK↑
1
—
1
—
ns
tSU
Set-up Time, data before CLK↑
1.3
—
1.3
—
ns
tSU
Set-up Time, CLKEN LOW before CLK↑
1.8
—
1.8
—
ns
tH
Hold Time, data after CLK↑
2
—
2
—
ns
tH
Hold Time, CLKEN LOW after CLK↑
1.3
—
1.3
—
ns
Output Skew(2)
—
—
—
1
ns
tSK(o)
NOTES:
1. See TEST CIRCUITS AND WAVEFORMS. TA = – 40°C to + 85°C.
2. Skew between any two outputs of the same package and switching in the same direction.
4
IDT74LVC823A
3.3V CMOS 9-BIT BUS-INTERFACE FLIP-FLOP
INDUSTRIAL TEMPERATURE RANGE
TEST CIRCUITS AND WAVEFORMS
TEST CONDITIONS
Symbol
VCC(1)= 3.3V±0.3V VCC(1)= 2.7V
VCC(2)= 2.5V±0.2V
Unit
VLOAD
6
6
2 x Vcc
V
VIH
2.7
2.7
Vcc
V
VT
1.5
1.5
Vcc / 2
V
VLZ
300
300
150
mV
VHZ
300
300
150
mV
CL
50
50
30
pF
VIN
Pulse (1, 2)
Generator
GND
tPZL
OUTPUT
SWITCH
NORMALLY
VLOAD
LOW
tPZH
OUTPUT SWITCH
NORMALLY
GND
HIGH
500Ω
LVC Link
Switch
DATA
INPUT
VLOAD
TIMING
INPUT
Disable High
Enable High
GND
ASYNCHRONOUS
CONTROL
All Other Tests
Open
SYNCHRONOUS
CONTROL
VIH
VT
0V
tPHL1
tSK (x)
tSK (x)
VOH
VOH-VHZ
0V
VT
0V
tSU
VIH
VT
0V
VIH
VT
0V
VIH
VT
0V
VIH
VT
0V
tH
tREM
tSU
tH
Set-up, Hold, and Release Times
VOH
VT
VOL
LOW-HIGH-LOW
PULSE
VT
tW
HIGH-LOW-HIGH
PULSE
tPHL2
VT
Pulse Width
tSK(x) = tPLH2 - tPLH1 or tPHL2 - tPHL1
Output Skew - tSK(X)
tPHZ
LVC Link
VOH
VT
VOL
OUTPUT 2
VLOAD/2
VOL+VLZ
VOL
Enable and Disable Times
SWITCH POSITION
Open Drain
Disable Low
Enable Low
tPLZ
VLOAD/2
VT
NOTE:
1. Diagram shown for input Control Enable-LOW and input Control Disable-HIGH.
NOTES:
1. Pulse Generator for All Pulses: Rate ≤ 10MHz; tF ≤ 2.5ns; tR ≤ 2.5ns.
2. Pulse Generator for All Pulses: Rate ≤ 10MHz; tF ≤ 2ns; tR ≤ 2ns.
Test
VIH
VT
0V
LVC Link
DEFINITIONS:
CL = Load capacitance: includes jig and probe capacitance.
RT = Termination resistance: should be equal to ZOUT of the Pulse Generator.
tPLH2
DISABLE
ENABLE
Test Circuit for All Outputs
OUTPUT 1
VIH
VT
0V
CONTROL
INPUT
CL
tPLH1
tPHL
Propagation Delay
D.U.T.
INPUT
tPLH
LVC Link
VOUT
RT
tPHL
OPPOSITE PHASE
INPUT TRANSITION
Open
500Ω
tPLH
OUTPUT
VLOAD
VCC
VIH
VT
0V
VOH
VT
VOL
SAME PHASE
INPUT TRANSITION
LVC Link
NOTES:
1. For tSK(o) OUTPUT1 and OUTPUT2 are any two outputs.
2. For tSK(b) OUTPUT1 and OUTPUT2 are in the same bank.
5
LVC Link
IDT74LVC823A
3.3V CMOS 9-BIT BUS-INTERFACE FLIP-FLOP
INDUSTRIAL TEMPERATURE RANGE
ORDERING INFORMATION
X
LVC
IDT
XX
Bus-Hold
Temp. Range
XX
XXXX
Device Type Package
PY
Q
PG
Shrink Small Outline Package
Quarter Size Small Outline Package
Thin Shrink Small Outline Package
823A
9-Bit Bus-Interface Flip-Flop with 3-State Outputs, ±24mA
Blank
No Bus-hold
74
–40°C to +85°C
CORPORATE HEADQUARTERS
2975 Stender Way
Santa Clara, CA 95054
for SALES:
800-345-7015 or 408-727-6116
fax: 408-492-8674
www.idt.com
6
for Tech Support:
[email protected]
(408) 654-6459