DATA SHEET SE5005L: 5 GHz Power Amplifier with Power Detector Applications • DSSS 5 GHz WLAN (IEEE802.11a) • Access points • PCMCIA cards • PC cards Features Figure 1. SE5005L Block Diagram • 5 GHz matched +18 dBm PA • Integrated PA enable pin (VEN) • Buffered, temperature-compensated power detector • High and low linearity modes • 3% EVM, @ +18 dBm, 64 QAM, 54 Mbps • +30 dB typical gain • DC blocked • QFN (16-pin, 3.0 mm x 3.0 mm x 0.9 mm) package (MSL1 @ 260 °C per JEDEC J-STD-020) Description The SE5005L is a 5 GHz Power Amplifier (PA) that offers high linear power for wireless LAN applications. The SE5005L offers a high level of integration for a simplified design, which provides quicker time-to-market and higher application board production yield. The SE5005L integrates all matching elements, a 3.8 GHz notch filter, and a temperaturecompensated, load-insensitive power detector with +20 dB of dynamic range. For wireless LAN applications, the SE5005L meets the requirements of IEEE 802.11a and delivers approximately +18 dBm of linear output power. The SE5005L also features a linearity mode-control function to reduce current consumption at low power. The SE5005L integrates the reference voltage generator, which allows for a true Complementary Metal Oxide Semiconductor (CMOS) compatible digital enable (EN) function to turn the PA on and off. A functional block diagram is shown in Figure 1. The pin configuration and package are shown in Figure 2. Signal pin assignments and functional pin descriptions are provided in Table 1. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202446B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • April 3, 2013 1 DATA SHEET • SE5005L: 5 GHZ POWER AMPLIFIER WITH POWER DETECTOR Figure 2. SE5005L Pinout (Top View) Table 1. SE5005L Signal Descriptions Pin # Name 1 VCC2 2 EN 3 Description Pin # Name Description Bias and driver supply voltage 9 GND Ground PA enable 10 GND Ground GND Ground 11 GND Ground 4 RFIN TX RF input signal 12 RFOUT 5 GND Ground 13 GND Ground 6 GND Ground 14 DET Power detector output 7 GND Ground 15 H/L Lin High to low linearity control 8 GND Ground 16 VCC1 Power stage supply voltage 5 GHz antenna output Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 2 April 3, 2013 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202446B DATA SHEET • SE5005L: 5 GHZ POWER AMPLIFIER WITH POWER DETECTOR Table 2. SE5005L Absolute Maximum Ratings Parameter Symbol Minimum Maximum Units Supply voltage on VCC1 and VCC2 pins VCC –0.3 4.2 V DC input on Enable EN –0.3 3.6 V +12 dBm 150 °C 350 V RF input power, RF_OUT into 50 Ω match RFIN Storage temperature range TSTG Electrostatic discharge—Human Body Model (HBM), JEDEC JESD22-A114 all pins Note: –40 ESDHBM Exposure to maximum rating conditions for extended periods may reduce device reliability. There is no damage to device with only one parameter set at the limit and all other parameters set at or below their nominal value. Exceeding any of the limits listed here may result in permanent damage to the device. CAUTION: Although this device is designed to be as robust as possible, Electrostatic Discharge (ESD) can damage this device. This device must be protected at all times from ESD. Static charges may easily produce potentials of several kilovolts on the human body or equipment, which can discharge without detection. Industry-standard ESD precautions should be used at all times. Table 3. Recommended Operating Conditions Parameter Symbol Minimum Maximum Units Supply voltage on VCC1 and VCC2 pins VCC 3.0 3.6 V Ambient Temperature TA –40 85 °C Electrical and Mechanical Specifications The absolute maximum ratings of the SE5005L are provided in Table 2. The recommended operating conditions are specified in Table 3, and electrical specifications are provided in Tables 4 and 5. The state of the SE5005L is determined by the logic provided in Table 6. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202446B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • April 3, 2013 3 DATA SHEET • SE5005L: 5 GHZ POWER AMPLIFIER WITH POWER DETECTOR Table 4. SE5005L Electrical Specifications: Transmit (Tx) AC Characteristics (Note 1) (VCC = VEN = C0 = H/L Lin = 3.3 V, TA = +25 °C, as Measured on Skyworks SE5005L-EK1 Evaluation Board, Unless Otherwise Noted) Parameter Symbol Frequency range Test Condition f Min. Typ. Max. Units 5.75 GHz 5.15 Output power, 802.11a, 64 QAM: EVM = 3% EVM < 2.2% MCS0, HT20, mask compliant MCS0, HT40, mask compliant +18 +16 +22 +21 EVM = 3% EVM < 2.2% MCS0, HT20, mask compliant MCS0, HT40, mask compliant +17 +15 +20 +19 P1dB No modulation +27 +23 dBm S11 PIN = –25 dBm +22 +25 dBm S21 PIN = –25dBm High linearity mode Low linearity mode +10 +27 +23 +14 High linearity mode H/L Lin = 3.3 V POUT Low linearity mode H/L Lin = 0 V Output 1dB compression point Input return loss dBm 0 Gain: Small signal Small signal variation ΔS21 Out of band S21_3.8 Harmonic 2f 3f Rise and fall time Gain variation over single 40 MHz channel Gain variation over band STAB Ruggedness—tolerance to output load mismatching RU Robustness tolerance to input power dB +0.5 +1.5 –1.5 Gain at 3.8 GHz +10 –50 –60 POUT = +18 dBm, OFDM tR, tF Stability +34 +32 –42 –42 dBm/MHz 0.5 POUT = +18 dBm, 54 Mbps, 64 QAM, VSWR = 6:1, all phases µs All non-harmonically related outputs less than –50 dBc/100 kHz PIN = +12 dBm, CW, VSWR = 6:1, all phases No damage PIN = +12 dBm, CW, VSWR = 6:1, all phases No damage Note 1: Performance is guaranteed only unde0r the conditions listed in the above Table. Table 5. SE5005L Power Detector Characteristics (Note 1) (VCC = VEN = 3.3 V, f = 5.4 GHz, TA = +25 °C, as Measured on Skyworks SE2432L-EK1 Evaluation Board, Unless Otherwise Noted) Parameter Symbol POUT detect range PDR Detector voltage VDET22 VDET16 VDET2 Output impedance PDZOUT Test Condition POUT = +22 dBm POUT = +16 dBm POUT = +2 dBm Minimum Typical Maximum Units 0 P1dB dBm 0.80 0.55 0.25 1.0 0.60 0.35 V 5 Note 1: Performance is guaranteed only under the conditions listed in the above Table. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 4 April 3, 2013 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202446B kΩ DATA SHEET • SE5005L: 5 GHZ POWER AMPLIFIER WITH POWER DETECTOR Detector Performance over Frequency and Temperature 1.0 25C, 4.90GHz 25C, 5.09GHz 0.9 25C, 5.28GHz Detector Voltage (V) 25C, 5.47GHz 25C, 5.66GHz 0.8 25C, 5.85GHz 85C, 4.90GHz 0.7 85C, 5.09GHz 85C, 5.28GHz 0.6 85C, 5.47GHz 85C, 5.66GHz 0.5 85C, 5.85GHz 0C, 4.90GHz 0C, 5.09GHz 0.4 0C, 5.28GHz 0C, 5.47GHz 0.3 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 0C, 5.66GHz 0C, 5.85GHz Output Power (dBm) Figure 3. SE5005L Power Detector Sweep over Temperature and Frequency Detector Error @VSWR=2:1 Vdet=0.463V Vdet=0.551V Vdet=0.670 V 19 Max ∆ = 0.49dB at 50Ω = 18dBm 2:1 50Ω 18 Output Power (dBm) 17 16 Max ∆ = 0.48dB at 50Ω = 15dBm 2:1 50Ω 15 14 13 Max ∆ = 0.45dB at 50Ω = 12dBm 2:1 50Ω 12 11 0 30 60 90 120 150 180 210 240 270 300 330 360 Phase (deg) Figure 4. SE5005L Power Detector Accuracy at 2:1 Mismatch Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202446B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • April 3, 2013 5 DATA SHEET • SE5005L: 5 GHZ POWER AMPLIFIER WITH POWER DETECTOR Table 6. SE5005L Logic Control Characteristics (VCC = VEN = 3.3 V, TA = +25 °C, as Measured on Skyworks SE5005L-EV1 Evaluation Board, Unless Otherwise Noted) Parameter Symbol Test Condition ICC-802.11a POUT = +18 dBm, 54 Mbps, 64 QAM, H/L Lin = 3.3V (high linearity mode) POUT = +14 dBm, 54 Mbps, 64 QAM, H/L Lin = 0V (low linearity mode) POUT = +5 dBm, 54 Mbps, 64 QAM, H/L Lin = 0V (low linearity mode) 195 140 108 mA mA mA VEN = 0 V, No RF 0.5 µA Supply current IOFF Logic voltage: High Low VENH VENL Input current logic voltage: High Low IENH IENL Minimum Typical +2.8 –0.3 Maximum Units +3.6 +0.3 V 400 µA µA <1 Package Dimensions Branding information is shown in Figure 5. Package dimensions are shown in Figure 6, the recommended land and solder pattern is shown in Figure 7, and tape and reel dimensions are provided in Figure 5. The SE5005L is rated to Moisture Sensitivity Level 1 (MSL1) at 260 °C, and can be used for lead or lead-free soldering. For additional information, refer to the Skyworks Application Note, Solder Reflow Information (Document Number 200164). Package and Handling Information Care must be taken when attaching this product, whether it is done manually or in a production solder reflow environment. Production quantities of this product are shipped in a standard tape and reel format. Instructions on the shipping container label regarding exposure to moisture after the container seal is broken must be followed. Otherwise, problems related to moisture absorption may occur when the part is subjected to high temperatures during solder assembly. Figure 5. SE5005L Typical Part Marking (Top View) Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 6 April 3, 2013 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202446B V DATA SHEET • SE5005L: 5 GHZ POWER AMPLIFIER WITH POWER DETECTOR Figure 6. SE5005L Package Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202446B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • April 3, 2013 7 DATA SHEET • SE5005L: 5 GHZ POWER AMPLIFIER WITH POWER DETECTOR Figure 7. SE5005L Recommended Land and Solder Pattern Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 8 April 3, 2013 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202446B DATA SHEET • SE5005L: 5 GHZ POWER AMPLIFIER WITH POWER DETECTOR Figure 8. SE5005L Tape and Reel Information Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202446B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • April 3, 2013 9 DATA SHEET • SE5005L: 5 GHZ POWER AMPLIFIER WITH POWER DETECTOR Ordering Information Model Name SE5005L: 5 GHz Power Amplifier with Power Detector Manufacturing Part Number SE5005L Evaluation Board Part Number SE5005L-EK1 Copyright © 2012, 2013 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks, the Skyworks symbol, and “Breakthrough Simplicity” are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 10 April 3, 2013 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202446B