DATA SHEET SKY13442-553LF: 0.4-2.7 GHz SP10T Switch with GPIO Interface Applications 2G/3G multimode cellular handsets (UMTS, CDMA2000, EDGE, GSM) Embedded data cards TRX1 TRX2 TRX3 Features Broadband frequency range: 0.4 to 2.7 GHz Single, positive DC power supply (2.5 to 3.3 V) Excellent Band 13 2nd harmonic rejection Integrated, low-pass harmonic filter for GSM transmit paths Integrated GPIO interface Any of eight TRX ports can be used for WCDMA transmit/receive or GSM receive functions Small QFN (20-pin, 2.5 x 2.5 mm) package (MSL1, 260 C per JEDEC J-STD-020) TRX4 TRX5 ANT TRX6 TRX7 TRX8 TX1 TX2 V4 V3 V2 V1 GPIO Interface VDD Skyworks Green™ products are compliant with all applicable legislation and are halogen-free. For additional information, refer to Skyworks Definition of Green™, document number SQ04-0074. S2884 Figure 1. SKY13442-553LF Block Diagram Description The SKY13442-553LF is a Single Pole, Ten-Throw (SP10T) antenna switch with an integrated General Purpose Input/Output (GPIO) interface and dual low-pass harmonic filters. The switch has eight transmit/receive ports, any of which can be used for WCDMA transmit/receive or GSM receive functions. Using advance switching technologies, the SKY13442-553LF maintains low insertion loss and high isolation for both transmit and receive switching paths. The switch also exhibits an excellent triple beat ratio and 2nd/3rd order modulation distortion performance. Switching is controlled by an integrated GPIO interface. Depending on the logic applied to the decoder, the antenna pin is connected to one of ten switched RF ports using a low insertion loss path, while the paths between the antenna pin and the other RF pins are in a high isolation state. No external DC blocking capacitors are required on the RF paths. The SKY13442-553LF is manufactured in a compact, 2.5 x 2.5 mm, 20-pin Quad Flat No-Lead (QFN) package. A functional block diagram is shown in Figure 1. The pin configuration and package are shown in Figure 2. Signal pin assignments and functional pin descriptions are provided in Table 1. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 201819B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • July 16, 2013 1 V1 V2 V3 V4 VDD DATA SHEET • SKY13442-553LF SP10T SWITCH WITH GPIO INTERFACE 20 19 18 17 16 2 14 TRX2 TRX6 3 13 TRX1 GND 4 12 TRX7 ANT 5 11 TRX8 6 7 8 9 10 GND TRX5 TX1 TRX3 GND 15 TX2 1 GND TRX4 S2887 Figure 2. SKY13442-553LF Pinout – 20-Pin QFN (Top View) Table 1. SKY13442-553LF Signal Descriptions Pin # Name Description Pin # Name Description 1 TRX4 RF input/output port 4 11 TRX8 RF input/output port 8 2 TRX5 RF input/output port 5 12 TRX7 RF input/output port 7 3 TRX6 RF input/output port 6 13 TRX1 RF input/output port 1 4 GND Ground 14 TRX2 RF input/output port 2 5 ANT Antenna RF port 15 TRX3 RF input/output port 3 6 GND Ground 16 VDD DC power supply 7 TX2 GSM high band transmit RF input port with integrated harmonic filter 17 V4 DC input control voltage 4 8 GND Ground 18 V3 DC input control voltage 3 9 TX1 GSM low band transmit RF input port with integrated harmonic filter 19 V2 DC input control voltage 2 10 GND Ground 20 V1 DC input control voltage 1 Note: Bottom ground paddles must be connected to ground. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 2 July 16, 2013 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 201819B DATA SHEET • SKY13442-553LF SP10T SWITCH WITH GPIO INTERFACE Table 2. SKY13442-553LF Absolute Maximum Ratings Parameter Maximum Units PIN +36 dBm 5 V DC control voltage VCTRL 2.7 V Storage temperature TSTG –40 +125 C Operating temperature TOP –30 +90 C RF input power Symbol Minimum Power supply Note: Exposure to maximum rating conditions for extended periods may reduce device reliability. There is no damage to device with only one parameter set at the limit and all other parameters set at or below their nominal value. Exceeding any of the limits listed here may result in permanent damage to the device. CAUTION: Although this device is designed to be as robust as possible, Electrostatic Discharge (ESD) can damage this device. This device must be protected at all times from ESD. Static charges may easily produce potentials of several kilovolts on the human body or equipment, which can discharge without detection. Industry-standard ESD precautions should be used at all times. Electrical and Mechanical Specifications The absolute maximum ratings of the SKY13442-553LF are provided in Table 2. Electrical specifications are provided in Table 3. Table 4 provides the control logic for the SKY13442553LF. Typical performance characteristics of the SKY13442-553LF are illustrated in Figures 3 to 12. WCDMA Band 1 linearity of the antenna switch. A +20 dBm Continuous Wave (CW) signal, fFUND, is sequentially applied to the TRX1 through TRX8 ports, while a –15 dBm CW blocker signal, fBLK, is applied to the ANT port. The resulting 3rd Order Intermodulation Distortion (IMD3), fRX, is measured over all phases of fFUND. The SKY13442-553LF exhibits exceptional performance for all TRX ports. Figure 13 illustrates the test setup used to measure data for Figure 10. This industry standardized test is used to simulate the Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 201819B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • July 16, 2013 3 DATA SHEET • SKY13442-553LF SP10T SWITCH WITH GPIO INTERFACE Table 3. SKY13442-553LF Electrical Specifications (Note 1) (1 of 2) (VDD = 2.85 V, CTLA = CTLB = CTLC = CTLD = 0/1.8 V, TOP = +25 C, PIN = 0 dBm, Characteristic Impedance [ZO] = 50 Ω, Unless Otherwise Noted) Parameter Symbol Test Condition Min Typical Max Units 704 to 787 MHz, ANT to TRX 0.45 0.60 dB RF Specifications Insertion Loss IL Insertion Loss (TRX1-3) IL Insertion Loss (TRX4-6) Insertion Loss (TRX7-8) IL IL 824 to 960 MHz, ANT to TRX 0.55 0.70 dB 1710 to 2170 MHz, ANT to TRX 0.70 0.85 dB 2300 to 2690 MHz, ANT to TRX 0.85 1.05 dB 824 to 960 MHz, ANT to TRX 0.55 0.70 dB 1710 to 2170 MHz, ANT to TRX 0.70 0.85 dB 2300 to 2690 MHz, ANT to TRX 0.85 1.00 dB 824 to 960 MHz, ANT to TRX 0.55 0.70 dB 1710 to 2170 MHz, ANT to TRX 0.70 0.85 dB 2300 to 2690 MHz, ANT to TRX 0.95 1.10 dB Insertion loss: ANT to TX1 port IL 824 to 915 MHz 1.15 1.35 dB Insertion loss: ANT to TX2 port IL 1710 to 1910 MHz 1.15 1.35 dB Isolation (TRX1/2/3/7/8 to TRX4/5/6 ports) ISO 824 to 1910 MHz 42 45 dB Isolation (TX1 to TRX1 through TRX8[RX2] ports) ISO 824 to 915 MHz 40 43 dB Isolation (TX2 to TRX1 through TRX8[RX2] ports) ISO 1710 to 1910 MHz 40 43 dB Isolation (TRx4 to TRx6) ISO 824 to 1910MHz 27 30 dBm Adjacent port isolation ISO_ADJ 824 to 1990 MHz 21 Band 13 2nd harmonic B13 2fo PIN = +25 dBm, f = 787 MHz, TRX1 to TRX8 –80 –78 dBm UMTS, PIN = +27 dBm: –67 –45 dBm TX1 port, PIN = +35 dBm –49 –36 dBm TX2 port, PIN = +33 dBm –52 –36 dBm Harmonics Attenuation (TX1 port) Attenuation (TX2 port) 24 GSM850: 2f 3f >4f 21 25 24 28 20 dB dB dB EGSM900: 2f 3f >4f 25 25 28 28 20 dB dB dB DCS1800: 2f 3f >4f 25 25 28 28 20 dB dB dB PCS1900: 2f 3f >4f 24 25 27 28 15 dB dB dB Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 4 dB July 16, 2013 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 201819B DATA SHEET • SKY13442-553LF SP10T SWITCH WITH GPIO INTERFACE Table 3. SKY13442-553LF Electrical Specifications (Note 1) (2 of 2) (VDD = 2.85 V, CTLA = CTLB = CTLC = CTLD = 0/1.8 V, TOP = +25 C, PIN = 0 dBm, Characteristic Impedance [ZO] = 50 Ω, Unless Otherwise Noted) Parameter Symbol Test Condition Min Typical 14 18 Max Units RF Specifications (continued) Return loss |S11| 0.4 to 2.2 GHz 2nd Order Input Intercept Point IIP2 AWS, PCS, IMT to CDMA2000 modes 2nd Order Intermodulation Distortion IMD2 UMTS mode –110 –105 dBm 3rd Order Intermodulation Distortion IMD3 UMTS mode –110 –105 dBm Triple Beat Ratio TBR Switching speed dB +95.5 dBm 650 to 900 MHz 81 91 dBc 1710 to 2155 MHz 81 91 dBc 10/90% RF 3 5 μs 2.85 3.30 V 50 100 μA 1.80 2.50 0.45 V V 3 3 5 5 μA μA DC Specifications Supply voltage VDD 2.50 Supply current IDD Control voltage: High Low CTLA, CTLB, CTLC, CTLD 1.35 0 Control current: High Low Note 1: Performance is guaranteed only under the conditions listed in this Table. Table 4. SKY13442-553LF Mode Control Logic Insertion Loss State V1 (Pin 20) V2 (Pin 19) V3 (Pin 18) V4 (Pin 17) Standby (all ports in isolation state) 0 0 0 0 ANT to TX1 1 1 0 0 ANT to TX2 1 0 0 0 ANT to TRX7 0 1 1 0 ANT to TRX8 0 1 0 0 ANT to TRX1 0 0 1 0 ANT to TRX2 1 0 1 0 ANT to TRX3 1 1 1 0 ANT to TRX4 1 0 1 1 ANT to TRX5 1 1 1 1 ANT to TRX6 1 0 0 1 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 201819B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • July 16, 2013 5 DATA SHEET • SKY13442-553LF SP10T SWITCH WITH GPIO INTERFACE Typical Performance Characteristics (VDD = 2.85 V, CTLA = CTLB = CTLC = CTLD = 0/1.8 V, TOP = +25 C, PIN = 0 dBm, Characteristic Impedance [ZO] = 50 Ω, Unless Otherwise Noted) 0 0 –0.2 –0.2 –0.4 –0.6 –0.6 Insertion Loss (dB) Insertion Loss (dB) –0.4 –0.8 –1.0 –1.2 –1.4 –1.6 –1.0 –1.2 –1.4 –1.6 –1.8 –2.0 0.7 –0.8 –1.8 0.9 1.1 1.3 1.5 1.7 1.9 2.1 2.3 2.5 2.7 –2.0 0.80 0.82 0.84 0.86 Frequency (GHz) 0.88 0.90 0.92 Frequency (GHz) Figure 3. Insertion Loss vs Frequency (ANT to All TRX Ports) Figure 4. Insertion Loss vs Frequency (ANT to TX1 Port) 0 –5 0 –0.2 GSM_TX_LB GSM_TX_HB –10 –15 –0.6 Attenuation (dB) Insertion Loss (dB) –0.4 –0.8 –1.0 –1.2 –20 –25 –30 –1.4 –35 –1.6 –40 –1.8 –2.0 1.65 1.70 1.75 1.80 1.85 Frequency (GHz) Figure 5. Insertion Loss vs Frequency (ANT to TX2 Port) 1.90 1.95 –45 0.5 1.5 2.5 3.5 4.5 5.5 6.5 7.5 8.5 9.5 10.5 11.5 12.5 Frequency (GHz) Figure 6. Attenuation vs Frequency (ANT to TX1/2 Ports) Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 6 July 16, 2013 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 201819B 0.94 DATA SHEET • SKY13442-553LF SP10T SWITCH WITH GPIO INTERFACE –10 –10 GSM_TX_LB-TRX1 GSM_TX_LB-TRX2 GSM_TX_LB-TRX3 GSM_TX_LB-TRX4 GSM_TX_LB-TRX5 –30 –40 –50 –60 0.80 GSM_TX_HB to TRX1 GSM_TX_HB to TRX2 GSM_TX_HB to TRX3 GSM_TX_HB to TRX4 GSM_TX_HB to TRX5 –20 Isolation (dB) Isolation (dB) –20 –30 –40 –50 0.82 0.84 0.86 0.88 0.90 0.92 0.94 0.96 0.98 1.00 –60 1.70 1.72 1.74 1.76 1.78 1.80 1.82 1.84 1.86 1.88 1.90 1.92 1.94 1.96 Frequency (GHz) Frequency (GHz) Figure 7. Isolation vs Frequency (TX1 to TRX Ports) Figure 8. Isolation vs Frequency (TX2 to TRX Ports) –10 –100 TRX1 (On) to TRX4 TRX1 (On) to TRX5 TRX1 (On) to TRX6 –105 IMD3 (dBm) Isolation (dB) –20 –30 –40 –50 –60 0.8 TRX1 TRX2 TRX3 TRX4 TRX5 –110 –115 –120 1.0 1.2 1.4 1.6 1.8 Frequency (GHz) Figure 9. Isolation vs Frequency (TRX1 to TRX4/5/6 Ports) 2.0 2.2 –125 0 15 30 45 60 75 90 105 120 135 150 165 180 Phase (Deg) Figure 10. 3rd Order Intermodulation Distortion vs Phase, TRX Ports (fFUND = 1.95 GHz, fBLK = 1.76 GHz, fRX = 2.14 GHz) Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 201819B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • July 16, 2013 7 –30 –30 –35 –35 –40 –40 –45 –50 –55 837 MHz: 2fo 837 MHz: 3fo 900 MHz: 2fo 900 MHz: 3fo –60 –65 –70 0 15 30 45 60 75 90 105 120 135 150 165 180 Harmonic Levels (dBm) Harmonic Levels (dBm) DATA SHEET • SKY13442-553LF SP10T SWITCH WITH GPIO INTERFACE –45 –50 –55 –60 1750 MHz: 2fo 1750 MHz: 3fo 1880 MHz: 2fo 1880 MHz: 3fo –65 –70 0 15 30 45 60 75 90 105 120 135 150 165 180 Phase (Deg) Phase (Deg) Figure 11. Harmonics vs Phase (ANT to TX1, PIN = +35 dBm, 5:1 VSWR Mismatch) Figure 12. Harmonics vs Phase (ANT to TX2, PIN = +33 dBm, 5:1 VSWR Mismatch) fBLK 1760 MHz, –15 dBm fFUND 1950 MHz, +20 dBm fRX 2140 MHz, Measure Tone Circulator Signal Generator fFUND = 1950 MHz, +20 dBm Coupler to Monitor Input Power 1950 MHz Bandpass Filter Circulator Duplexer Phase Shifter SKY13442-553 fFUND = +20 dBm fBLK = –15 dBm 1760 MHz Bandpass Filter Signal Generator fBLK = 1760 MHz, –15 dBm Spectrum Analyzer fRX = 2140 MHz S1970k Figure 13. 3rd Order Intermodulation Test Setup Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 8 July 16, 2013 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 201819B DATA SHEET • SKY13442-553LF SP10T SWITCH WITH GPIO INTERFACE Evaluation Board Description Package and Handling Information The SKY13442-553LF Evaluation Board is used to test the performance of the SKY13442-553LF SP10T Switch. An Evaluation Board schematic diagram is provided in Figure 14. A recommended ESD protection circuit diagram is provided in Figure 15. An assembly drawing for the Evaluation Board is shown in Figure 16. Instructions on the shipping container label regarding exposure to moisture after the container seal is broken must be followed. Otherwise, problems related to moisture absorption may occur when the part is subjected to high temperature during solder assembly. Package Dimensions THE SKY13442-553LF is rated to Moisture Sensitivity Level 1 (MSL1) at 260 C. It can be used for lead or lead-free soldering. For additional information, refer to the Skyworks Application Note, Solder Reflow Information, document number 200164. The PCB layout footprint for the SKY13442-553LF is provided in Figure 17. Typical case markings are shown in Figure 18. Package dimensions for the 20-pin QFN are shown in Figure 19, and tape and reel dimensions are provided in Figure 20. Care must be taken when attaching this product, whether it is done manually or in a production solder reflow environment. Production quantities of this product are shipped in a standard tape and reel format. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 201819B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • July 16, 2013 9 DATA SHEET • SKY13442-553LF SP10T SWITCH 1 2 3 VDD V4 V3 V2 V1 GND DCH1 Header 4 5 6 C1 10 nF Transmit/Receive Port 4 1 Transmit/Receive Port 5 2 Transmit/Receive Port 6 3 17 16 VDD 18 V2 V1 19 C2 33 pF V4 20 C3 33 pF C4 33 pF C5 33 pF V3 C6 33 pF TRX4 TRX3 TRX5 TRX2 TRX6 TRX1 GND TRX7 ANT TRX8 6 7 8 9 Transmit/Receive Port 3 14 Transmit/Receive Port 2 13 Transmit/Receive Port 1 12 Transmit/Receive Port 7 11 Transmit/Receive Port 8 GND TX1 GND 5 GND Antenna TX2 4 15 10 Transmit Port TX2 Transmit Port TX1 Y0008 Figure 14. SKY13442-553LF Evaluation Board Schematic Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 10 July 16, 2013 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 201819B DATA SHEET • SKY13442-553LF SP10T SWITCH WITH GPIO INTERFACE 4.7 pF To Application Antenna To SKY13442-533LF Antenna (Pin 7) 18 nH 18 nH ESD Circuit 1 12 pF To Application Antenna To SKY13442-533LF Antenna (Pin 7) 8.2 nH ESD Circuit 2 Y0012 Figure 15. SKY13442-553LF Recommended ESD Protection Circuits Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 201819B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • July 16, 2013 11 DATA SHEET • SKY13442-553LF SP10T SWITCH WITH GPIO INTERFACE TRX2 TRX1 TRX3 TRX7 6 TRX8 5 VDD 3 V2 2 DCH1 4 V4 V3 TX1 1 V1 C2 C1 C3 C4 C5 C6 GND TX2 ANT TRX4 TRX5 TRX6 Y0009 Figure 16. SKY13442-553LF Evaluation Board Assembly Diagram Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 12 July 16, 2013 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 201819B DATA SHEET • SKY13442-553LF SP10T SWITCH WITH GPIO INTERFACE Pin 20 20X 0.975 R0.2 Pin 1 Indicator 20X 0.425 Pin 1 20X 0.180 0.400 Pitch 2X 0.700 Package Outline Exposed Soldering Area 0.400 Pitch 2X 0.750 All measurements in millimeters S2886 Figure 17. SKY13442-553LF PCB Layout Footprint (Top View) Pin 1 Indicator Skyworks Part # Lot # Figure 18. Typical Part Markings (Top View) Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 201819B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • July 16, 2013 13 C A 2.5 Pin 1 Indicator Seating Plane DATA SHEET • SKY13442-553LF SP10T SWITCH WITH GPIO INTERFACE 1.5 ± 0.1 Exposed Pad (0.750) (R 0.2) Pin 1 Indicator 0.02 + 0.03/–0.02 2.5 8X 0.400 20X 2 0.05 C 0.05 C 2X B 2X Detail A 0.05 C Top View 20X 0.075 Detail C Detail B 0.75 ± 0.05 0.05 C (0.700) Side View 1.4 ± 0.1 10X 0.200 Min. 8X 0.800 10X 0.175 Min. Bottom View 0.18 ± 0.05 0.18 ± 0.05 3 3 0.10 M C A B 0.2 ± 0.05 0.2 ± 0.05 0.10 M C A B 0.18 ± 0.05 0.2 ± 0.05 3 0.10 M C A B 4X R0.20 5X R0.20 5X R0.20 Detail A Detail B Detail C Scale: 80X 3X This Rotation 3X Rotated 180° 3X Rotated 90° CW 3X Rotated 90° CCW Scale: 80X 1X This Rotation 1X Rotated 180° 1X Rotated 90° CW 1X Rotated 90° CCW Scale: 80X 1X This Rotation 1X Rotated 180° 1X Rotated 90° CW 1X Rotated 90° CCW All measurements are in millimeters. Dimensioning and tolerancing according to ASME Y14.5M-1994. Coplanarity applies to the exposed heat sink slug as well as the terminals. Dimension applies to metalized terminal. If the terminal has a radius on its end, the dimension should not be measured in that area. Figure 19. SKY13442-553LF 20-Pin QFN Package Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 14 July 16, 2013 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 201819B S2885 DATA SHEET • SKY13442-553LF SP10T SWITCH WITH GPIO INTERFACE Pin #1 Indicator 2.70 ± 0.10 (Bo) A 4.00 ± 0.10 1.75 ± 0.10 (E) 4.00 ± 0.10 B A B 8.00 ± 0.20 (w) 2.00 ± 0.05 ø1.50 +0.10/–0 3.50 ± 0.05 0.25 ± 0.05 ø1.00 +0.10/–0 1.00 ± 0.10 (Ko) B 2.70 ± 0.10 (Ao) Notes: 1. Carrier tape: black conductive polystyrene. 2. Cover tape material: transparent conductive material. 3. 10 sprocket hole pitch cumulative tolerance: ±0.20 mm 4. Ao and Bo measured on plane 0.30 mm above the bottom of the pocket. 5. All measurements are in millimeters. A Y0010 Figure 20. SKY13442-553LF Tape and Reel Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 201819B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • July 16, 2013 15 DATA SHEET • SKY13442-553LF SP10T SWITCH WITH GPIO INTERFACE Ordering Information Model Name SKY13442-553LF 0.4-2.2 GHz SP10T Switch Manufacturing Part Number SKY13442-553LF Evaluation Board Part Number SKY13442-553LF-EVB Copyright © 2012-2013 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks, the Skyworks symbol, and “Breakthrough Simplicity” are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 16 July 16, 2013 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 201819B