INTERSIL HS1-3182-8

HS-3182
®
Data Sheet
May 30, 2008
ARINC 429 Bus Interface Line Driver
Circuit
FN2963.3
Features
The HS-3182 is a monolithic dielectric ally isolated bipolar
differential line driver designed to meet the specifications of
ARINC 429. This device is intended to be used with a
companion chip, HS-3282 CMOS ARINC Bus Interface
Circuit, which provides the data formatting and processor
interface function.
All logic inputs are TTL and CMOS compatible. In addition to
the DATA (A) and DATA (B) inputs, there are also inputs for
CLOCK and SYNC signals which are AND’d with the DATA
inputs. This feature enhances system performance and
allows the HS-3182 to be used with devices other than the
HS-3182.
Three power supplies are necessary to operate the HS-3182:
+V = +15V ±10%, -V = -15V ±10%, and V1 = 5V ±5%. VREF is
used to program the differential output voltage swing such that
VOUT (DIFF) = ±2VREF. Typically, VREF = V1 = 5V ±5%, but a
separate power supply may be used for VREF which should
not exceed 6V.
• RoHS/Pb-free Available for SBDIP Package (100% Gold
Termination Finish)
• TTL and CMOS Compatible Inputs
• Adjustable Rise and Fall Times via Two External
Capacitors
• Programmable Output Differential Voltage via VREF Input
• Operates at Data Rates Up to 100k Bits/s
• Output Short Circuit Proof and Contains Overvoltage
Protection
• Outputs are Inhibited (0V) If DATA (A) and DATA (B)
Inputs are Both in the “Logic One” State
• DATA (A) and DATA (B) Signals are “AND’d” with Clock
and Sync Signals
• Full Military Temperature Range
Pinouts
HS-3182
(16 LD SBDIP)
TOP VIEW
The driver output impedance is 75Ω ±20% at +25°C. Driver
output rise and fall times are independently programmed
through the use of two external capacitors connected to the CA
and CB inputs. Typical capacitor values are CA = CB = 75pF for
high-speed operation (100kBPS), and CA = CB = 300pF for
low-speed operation (12kBPS to 14.5kBPS). The outputs are
protected against overvoltage and short circuit as shown in the
Block Diagram. The HS-3182 is designed to operate over an
ambient temperature range of -55°C to +125°C, or -40°C to
+85°C.
VREF 1
16 V1
GND 2
15 NC
14 CLK
SYNC 3
13 DATA (B)
DATA (A) 4
CA 5
12 CB
AOUT 6
11 BOUT
-V 7
10 NC
GND 8
9 +V
TABLE 1. TRUTH TABLE
0V
0V
Null
L
X
X
X
0V
0V
Null
H
H
L
L
0V
0V
Null
H
H
L
H
-VREF +VREF
Low
H
H
H
L
+VREF -VREF
High
H
H
H
H
0V
0V
Null
HS-3182
(28 LD CLCC)
TOP VIEW
4
3
2
1
NC
X
V1
X
NC
L
VREF
X
NC
COMMENTS
GND
BOUT
SYNC
SYNC CLK DATA (A) DATA (B) AOUT
28 27 26
NC
5
25 CLK
DATA (A)
6
24 NC
NC
7
23 DATA (B)
NC
8
22 CB
CA
9
21 NC
NC 10
20 NC
NC 11
19 NC
1
NC
BOUT
+V
GND
-V
AOUT
NC
12 13 14 15 16 17 18
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright Intersil Americas Inc. 1997, 2007, 2008. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.
HS-3182
Ordering Information
PART
NUMBER
ORDERING
NUMBER
PART
MARKING
TEMP.
RANGE (°C)
PACKAGE
PKG.
DWG. #
HS1-3182-8
5962-8687901EA
HS1-3182-8 RD
-55 to +125
16 Ld SBDIP, Solder Seal (Pb-free)
D16.3
HS1-3182-9+
HS1-3182-9+
HS1-3182-9+ RD
-40 to +85
16 Ld SBDIP, Solder Seal (Pb-free)
D16.3
HS4-3182-8
5962-86879013A
HS4- 3182-8 RD
-55 to +125
28 Ld TER CLCC, Solder Seal
J28.A
NOTE: These Intersil Pb-free Hermetic packaged products employ 100% Au plate - e4 termination finish, which is RoHS compliant and compatible
with both SnPb and Pb-free soldering operations.
Block Diagram
(9) (5)
+V CA
(4)
OUTPUT
DRIVER
(A)
LEVEL SHIFTER
AND SLOPE
CONTROL (A)
DATA (A)
FA
(6)
AOUT
ROUT/2
(14)
CLOCK
(8)
(1)
VREF
GND
CL
RL
(3)
OUTPUT
DRIVER
ROUT/2
(B)
SYNC
LEVEL SHIFTER
AND SLOPE
CONTROL (B)
(13)
DATA (B)
FB
BOUT
(11)
(16)
V1
(2)
CURRENT
REGULATOR
-V
(7)
OVER-VOLTAGE
PROTECTION
CB
(12)
Typical Application
(9)
PIN NUMBERS INDICATED BY ( )
+5V
+15V
CA
(16)
(14)
(3)
(1)
(5)
V1 VREF
CB
(12)
CA
CB
+V
CLOCK
SYNC
AOUT
BOUT
HS-3182
ARINC DRIVER
CIRCUIT
31
429D0
HS-3282
CMOS ARINC
CIRCUIT
429D0
TO BUS
(SEE NOTE)
(4)
DATA (A)
32 (13)
DATA (B)
16 LEAD DIP
GND
(2)
GND
(8)
-V
(7)
PIN NUMBER 10, 15 = NC
-15V
NOTE: The rise and fall time of the outputs are set to ARINC specified values by CA and CB. Typical CA = CB = 75pF for high speed and 300pF for
low speed operation. The output HI and low levels are set to ARINC specifications by VREF.
2
FN2963.3
May 30, 2008
HS-3182
Absolute Maximum Ratings
Thermal Information
Voltage Between +V and -V Terminals . . . . . . . . . . . . . . . . . . . .40V
V1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7V
VREF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6V
Logic Input Voltage . . . . . . . . . . . . . . . . . . . GND -0.3V to V1 +0.3V
Output Short Circuit Duration. . . . . . . . . . . . . . . . . . . . . . . . (Note 3)
Output Overvoltage Protection. . . . . . . . . . . . . . . . . . . . . . . (Note 4)
Thermal Resistance (Typical)
θJA (°C/W)
θJC (°C/W)
SBDIP Package . . . . . . . . . . . . . . . . . .
68
12
CLCC Package . . . . . . . . . . . . . . . . . .
54
10
Storage Temperature Range . . . . . . . . . . . . . . . . . .-65°C to +150°C
Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . +175°C
Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
Operating Conditions
Die Characteristics
Operating Voltage
+V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +15V ±10%
-V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -15V ±10%
V1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5V ±5%
VREF (For ARINC 429) . . . . . . . . . . . . . . . . . . . . . . . . . . 5V ±5%
Operating Temperature Range
HS-3182-9+ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +85°C
HS-3182-8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-55°C to +125°C
Number of Transistors or Gates . . . . . . . . . . . . . . . . . . . . . . . . . 133
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and
result in failures not covered by warranty.
NOTES:
1. θJA is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
2. θJC, the “case temp” location is the center of the package underside.
3. Heat sink may be required for 100k bits/s at +125°C and output short circuit at +125°C.
4. The fuses used for output overvoltage protection may be blown by a fault at each output of greater than ±6.5V relative to GND.
DC Electrical Specifications
Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified.
Temperature limits established by characterization and are not production tested.
DC PARAMETER
CONDITIONS
(Note 5)
SYMBOL
MIN
MAX
UNITS
Supply Current +V (Operating)
ICCOP (+V)
No Load (0k to 100k bits/s)
-
16
mA
Supply Current -V (Operating)
ICCOP (-V)
No Load (0k to 100k bits/s)
-16
-
mA
Supply Current V1 (Operating)
ICCOP (V1)
No Load (0k to 100k bits/s)
-
975
µA
ICCOP (VREF)
No Load (0k to 100k bits/s)
-1.0
-
mA
Supply Current VREF (Operating)
Logic “1” Input Voltage
VIH
2.0
-
V
Logic “0” Input Voltage
VIL
-
0.5
V
Output Voltage High (Output to GND)
VOH
No Load (0k to 100k bits/s)
VREF
(-250mV)
VREF
(+250mV)
Output Voltage Low (Output to GND)
VOL
No Load (0k to 100k bits/s)
-VREF
(-250mV)
-VREF
(+250mV)
VNULL
No Load (0k to 100k bits/s)
-250
+250
mV
Output Voltage Null
Input Current (Input Low)
IIL
-20
-
mA
Input Current (Input High)
IIH
-
10
mA
Output Short Circuit Current
(Output High)
IOHSC
Short to GND
-
-80
mA
Output Short Circuit Current
(Output Low)
IOLSC
Short to GND
80
-
mA
TA = +25°C
60
90
Ω
Output Impedance
ZO
NOTES:
5. +V = +15V ±10%, -V = -15V ±10%, V1 = VREF = 5V ±5%, unless otherwise specified TA = -40°C to +85°C for HS-3182-9+ and
TA = -55°C to +125°C for HS-3182-8.
3
FN2963.3
May 30, 2008
HS-3182
AC Electrical Specifications
AC PARAMETER
CONDITIONS
(Note 6)
SYMBOL
Rise Time (AOUT, BOUT)
tR
MIN
MAX
UNITS
1
2
µs
0.9
2.4
µs
CA = CB = 300pF, (Note 7)
3
9
µs
CA = CB = 75pF, (Note 8)
1
2
µs
0.9
2.4
µs
CA = CB = 300pF, (Note 8)
3
9
µs
CA = CB = 75pF, (Note 7)
(at TA = -55°C Only)
Fall Time (AOUT, BOUT)
tF
(at TA = -55°C Only)
Propagation Delay Input to Output
tPLH
CA = CB = 75pF, No Load
-
3.3
µs
Propagation Delay Input to Output
tPHL
CA = CB = 75pF, No Load
-
3.3
µs
NOTES:
6. +V = +15V, -V = -15V, V1 = VREF = 5V, unless otherwise specified TA = -40°C to +85°C for HS-3182-9+ and TA = -55°C to +125°C for
HS-3182-8.
7. tR measured 50% to 90% x 2, no load.
8. tF measured 50% to 10% x 2, no load.
Electrical Specifications
PARAMETER
CONDITIONS
(NOTE 9)
SYMBOL
Input Capacitance
CIN
MIN
MAX
UNITS
TA = +25°C
-
15
pF
Supply Current +V (Short Circuit)
ISC (+V)
Short to GND, TA = +25°C
-
150
mA
Supply Current -V (Short Circuit)
ISC (-V)
Short to GND, TA = +25°C
-150
-
mA
NOTES:
9. Limits established by characterization and are not production tested.
Power Specifications
Nominal Power at +25°C, +V = +15V, -V = -15V, V1 = VREF = 5V, Notes 10, 12
DATA RATE
(k BITS/s)
+V
V-
V1
CHIP POWER
POWER DISSIPATION IN
LOAD
No Load
11mA
-10mA
600µA
325mW
0
12.5 to 14
Full Load, Note 11
24mA
-24mA
600µA
660mW
60mW
100
Full Load, Note 11
46mA
-46mA
600µA
1 Watt
325mW
0 to 100
LOAD
NOTES:
10. Heat sink may be required for 100k bits/s at +125°C and output short circuit at +125°C.
Thermal characteristics: T(CASE) = T(Junction) - θ(Junction - Case) P(Dissipation).
Where: T(Junction Max) = +175°C
θ(Junction - Case) = 10.9°C/W (6.1°C/W for LCC)
θ(Junction - Ambient) = 73.5°C/W (54.0°C/W for LCC)
11. Full Load for ARINC 429: RL = 400Ω and CL = 30,000pF in parallel between AOUT and BOUT (See “Block Diagram” on page 2).
12. Output Overvoltage Protection: The fuses used for output overvoltage protection may be blown by a fault at each output of greater than ±6.5V
relative to GND.
4
FN2963.3
May 30, 2008
HS-3182
Driver Waveforms
5V
0V
50%
DATA (A) 0V
5V
0V
50%
DATA (B) 0V
ADJ. BY
CB
VREF
+4.75V TO +5.25V
AOUT 0V
ADJ. BY
CA
tPHL
-4.75V TO -5.25V
VREF
+4.75V TO +5.25V
50%
BOUT 0V
-VREF
50%
tPLH
tR
DIFFERENTIAL
OUTPUT
-VREF
-4.75V TO -5.25V
2VREF
HIGH
AOUT - BOUT
+9.5V TO +10.5V
NULL
0V
-2VREF
NOTE: OUTPUTS UNLOADED
-9.5V TO -10.5V
LOW
tF
NOTES:
When the Data (A) input is in the Logic One state and the Data (B)
input is in the Logic Zero state, AOUT is equal to VREF and BOUT is
equal to -VREF. This constitutes the Output High state. Data (A) and
Data (B) both in the Logic Zero state causes both AOUT and BOUT
to be equal to 0V which designates the output Null state. Data (A) in
the Logic Zero state and Data (B) in the Logic One state causes
AOUT to be equal to -VREF and BOUT to be equal to VREF which is
the Output Low state.
tR measured 50% to 90% x 2
tF measured 50% to 10% x 2
VIH = 5V
VOL = -4.75V to -5.25V
VIL = 0V
VOH = 4.75V to 5.25V
Burn-In Schematic
V1
DATA (B)
+V
VIH
C3
16
15
1
2
14
13 12 11
HS-3182
3
4
5
6
A
10
9
7
8
R
C1
DATA (A)
VIH
B
C2
-V
VIL
VIL
GND
NOTES:
Ambient Temp. Max. = +125°C.
R = 400Ω ± 5%
Package = 16 Lead Side Brazed DIP.
C1 = 0.03mF ± 20%
Pulse Conditions = A & B = 6.25kHz ±10%. B is delayed one-half
cycle and in sync with A.
C2 = C3 = 500pF, NPO
+V = +15.5V ± 0.5V
VIH = 2.0V Min.
-V = -15.5V ± 0.5V
VIL = 0.5V Max.
V1 = +5.5V ± 0.5V
A 0.0mF decoupling capacitor is required on each of the three
supply lines (+V, -V and V1) at every 3rd Burn-In socket.
5
FN2963.3
May 30, 2008
HS-3182
Ceramic Leadless Chip Carrier Packages (CLCC)
J28.A
MIL-STD-1835 CQCC1-N28 (C-4)
28 PAD CERAMIC LEADLESS CHIP CARRIER PACKAGE
0.010 S E H S
D
INCHES
D3
SYMBOL
j x 45o
E3
B
E
h x 45o
0.010 S E F S
A
A1
PLANE 2
PLANE 1
-E-
B1
L
e
-H-
L3
MILLIMETERS
MAX
MAX
NOTES
A
0.060
0.100
1.52
2.54
6, 7
0.050
0.088
1.27
2.23
-
B
-
-
-
-
-
B1
0.022
0.028
0.56
0.71
2, 4
B2
0.072 REF
1.83 REF
-
B3
0.006
0.022
0.15
0.56
-
D
0.442
0.460
11.23
11.68
-
D1
0.300 BSC
7.62 BSC
-
D2
0.150 BSC
3.81 BSC
-
D3
-
0.460
E
0.442
0.460
11.23
11.68
2
11.68
-
E1
0.300 BSC
7.62 BSC
-
E2
0.150 BSC
3.81 BSC
-
E3
e
-
0.460
0.050 BSC
0.015
-
-
11.68
2
1.27 BSC
0.38
-
2
h
0.040 REF
1.02 REF
5
j
0.020 REF
0.51 REF
5
L
0.045
0.055
1.14
1.40
-
L1
0.045
0.055
1.14
1.40
-
L2
0.075
0.095
1.90
2.41
-
L3
0.003
0.015
0.08
0.038
-
ND
7
7
3
NE
7
7
3
N
28
28
-F-
3
Rev. 0 5/18/94
B3
E1
E2
MIN
A1
e1
0.007 M E F S H S
MIN
1. Metallized castellations shall be connected to plane 1 terminals
and extend toward plane 2 across at least two layers of ceramic
or completely across all of the ceramic layers to make electrical
connection with the optional plane 2 terminals.
L2
B2
L1
D2
e1
D1
NOTES:
2. Unless otherwise specified, a minimum clearance of 0.015 inch
(0.38mm) shall be maintained between all metallized features
(e.g., lid, castellations, terminals, thermal pads, etc.)
3. Symbol “N” is the maximum number of terminals. Symbols “ND”
and “NE” are the number of terminals along the sides of length
“D” and “E”, respectively.
4. The required plane 1 terminals and optional plane 2 terminals (if
used) shall be electrically connected.
5. The corner shape (square, notch, radius, etc.) may vary at the
manufacturer’s option, from that shown on the drawing.
6. Chip carriers shall be constructed of a minimum of two ceramic
layers.
7. Dimension “A” controls the overall package thickness. The maximum “A” dimension is package height before being solder dipped.
8. Dimensioning and tolerancing per ANSI Y14.5M-1982.
9. Controlling dimension: INCH.
6
FN2963.3
May 30, 2008
HS-3182
Ceramic Dual-In-Line Metal Seal Packages (SBDIP)
D16.3 MIL-STD-1835 CDIP2-T16 (D-2, CONFIGURATION C)
LEAD FINISH
c1
-A-
16 LEAD CERAMIC DUAL-IN-LINE METAL SEAL PACKAGE
-DBASE
METAL
E
b1
M
(b)
M
-Bbbb S C A - B S
(c)
SECTION A-A
D S
D
BASE
PLANE
Q
S2
-C-
SEATING
PLANE
A
L
S1
eA
A A
b2
b
e
eA/2
c
aaa M C A - B S D S
ccc M C A - B S D S
NOTES:
1. Index area: A notch or a pin one identification mark shall be located adjacent to pin one and shall be located within the shaded
area shown. The manufacturer’s identification shall not be used
as a pin one identification mark.
2. The maximum limits of lead dimensions b and c or M shall be
measured at the centroid of the finished lead surfaces, when
solder dip or tin plate lead finish is applied.
3. Dimensions b1 and c1 apply to lead base metal only. Dimension
M applies to lead plating and finish thickness.
4. Corner leads (1, N, N/2, and N/2+1) may be configured with a
partial lead paddle. For this configuration dimension b3 replaces
dimension b2.
5. Dimension Q shall be measured from the seating plane to the
base plane.
INCHES
SYMBOL
MIN
MILLIMETERS
MAX
MIN
MAX
NOTES
A
-
0.200
-
5.08
-
b
0.014
0.026
0.36
0.66
2
b1
0.014
0.023
0.36
0.58
3
b2
0.045
0.065
1.14
1.65
-
b3
0.023
0.045
0.58
1.14
4
c
0.008
0.018
0.20
0.46
2
c1
0.008
0.015
0.20
0.38
3
D
-
0.840
-
21.34
-
E
0.220
0.310
5.59
7.87
-
e
0.100 BSC
2.54 BSC
-
eA
0.300 BSC
7.62 BSC
-
eA/2
0.150 BSC
3.81 BSC
-
L
0.125
0.200
3.18
5.08
-
Q
0.015
0.060
0.38
1.52
5
S1
0.005
-
0.13
-
6
S2
0.005
-
0.13
-
7
α
90o
105o
90o
105o
-
aaa
-
0.015
-
0.38
-
bbb
-
0.030
-
0.76
-
ccc
-
0.010
-
0.25
-
M
-
0.0015
-
0.038
2
N
16
16
8
Rev. 0 4/94
6. Measure dimension S1 at all four corners.
7. Measure dimension S2 from the top of the ceramic body to the
nearest metallization or lead.
8. N is the maximum number of terminal positions.
9. Braze fillets shall be concave.
10. Dimensioning and tolerancing per ANSI Y14.5M - 1982.
11. Controlling dimension: INCH.
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
7
FN2963.3
May 30, 2008