LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only 0.45W Power Light LED Pb Lead-Free Parts LG-5630WKZ-DT-2-P-NW-D01 DATA SHEET DOC. NO : QW0905-LG-5630WKZ-DT-2-P-NW-D01 REV. : A DATE : 30 - May. - 2011 發行 立碁電子 DCC LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Product Model Designation System LG - 56 30 WK Z - D T - 2 - P - NW - D01 X1 X2 X1 Title LG:Ligitek X3 X4 X2 Dimension(L) 57:5.7mm 56:5.6mm X5 X6 X7 X8 X9 X10 X11 X3 X4 X5 Dimension(W) Emitting Color Zener 30:3.0mm WK:White Color X6 X7 X8 X9 X10 Epoxy Color Package T:Tape&Reel Chip Modification Patent Chromaticity Coordinates -X: 2 chip in 1(Parallel) P: IP Free -CW: Cool White -NW: Neutral White -WW: Warm White D:Yellow Diffused -1: 1 chip in 1 -2: 2 chip in 1(Series) X11 Bin Modification Page 1/15 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Typical Applications Features *. White colored SMTpackage *.Suitable for all SMT assembly and soldering methodes *. Pb-Free Reflow soldering application *. More Energy Efficient than lncandescent and most Halogen lamps. *. RoHS compliant *. Reading Light (car,bus,aircraft) *. Portable(flashlight,bicycle). *. Backlights(Monitor,TV) / Light Guides. *. Automotive Exterior (Stop-Tail-Tum,CHMSL,Mirror Side Repeat). *. Commercial and Residential Architectural lighting. *. Mini-accent / Uplighters / Downlighters / Orientation lighting *. Fiber Optic Alternative / Decorative / Entertainment lighting. *. Security / Garden lighting. *. Cove / Undershelf / Task lighting. *. Traffic signaling / Beacons / Rail crossing and Wayside lighting. Dimension 5.3 C 3.0 A C Recommended Solder Patterns 5.6 2.0 0.9 1.6 1.62 3.8 6.8 0.5 0.8 1.28 0.5 2.1 Slug Anode(+) 0.3 2.3 0.8 Cathode(-) Note: 1.The tolerance unless mentioned is ±0.1mm,unit=mm. 2.The slug has polarity as anode. 3.It is strongly recommended to apply on electrically isolated heat conducting film between the slug and contact surfaces. Page 2/15 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Absolute Maximum Ratings at Ta=25℃ Ratings Parameter Symbol UNIT White DC Forward Current IF 80 mA Power Dissipation PD 0.61 W Peak pulse current Duty 1/10@10KHz IFP 100 mA LED junction Temperature Tj 125 ℃ Reverse Current(VR=5V) Ir 10 µA ESD Sensitivity VB ±2000 V Storage Temperature Tstg -40 ~ +100 ℃ Operating Temperature Topr -40 ~ +85 ℃ Soldering Temperature Tp 260 ℃ Hand Soldering Time at320°C(Max) Tsol 3 seconds Note: 1.Proper current derating must be observed to maintain temperature below the maximum. 2.LEDS are not designed to be driven in reverse bias. Luminous Intensity Characteristics at 60mA (Ratings At 25°C Ambient) PART NO LG-5630WKZ-DT-2-P-NW-D01 Luminous Intensity Emission Color Min. Typ. Max. White 20 28 ---- Note : 1. White emitters are built with InGaN. 2. Luminous Intensity is measured with an accuracy of ±10% Page 3/15 Units lm LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Forward Voltage Characteristics at 60mA (Ratings At 25°C Ambient) PART NO LG-5630WKZ-DT-2-P-NW-D01 Vf Emission Color Min. Typ. Max. White ---- 6.6 7.6 Units V Note : Forward Voltage is measured with an accuracy of±0.1V Chromaticity Coordinates Characteristics at 60mA (Ratings At 25℃ Ambient ) PART NO LG-5630WKZ-DT-2-P-NW-D01 Emission Color White Chromaticity Coordinates (TYP.) X Y 0.3601 0.3642 Note : ±0.01 is tester tolerance. Emission Angle Characteristics at 60mA (Ratings At 25°C Ambient ) PART NO LG-5630WKZ-DT-2-P-NW-D01 Emission Color Lambertian Units White 120 Degrees Color Rendering Index Characteristics at 60mA (Ratings At 25°C Ambient ) PART NO LG-5630WKZ-DT-2-P-NW-D01 CRI Emission Color Min. Typ. Max. White 75 ---- ---- Page 4/15 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Bin Code Description Bin Code Luminous Intensity F28D Luminous Intensity (Lm) @IF=60mA Bin Code Min. Max. F20D 20 22 F22D 22 24 F24D 24 26 F26D 26 28 F28D 28 30 F30D 30 32 F32D 32 36 CIE Forward Voltage UO 6.4-6.6 Color Rank @IF=60mA Forward Voltage(V) @IF=60mA TN-UP 6.0-6.2 6.2-6.4 6.4-6.6 6.6-6.8 6.8-7.0 7.0-7.2 7.2-7.4 7.4-7.6 Page 5/15 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Bins Code of chromaticity coordinates Color Coordiante at 60mA CCT(K) 4100~4500 4500~5000 BIN CODE 1 X 2 Y X 3 Y X 4 Y X Y TN 0.361 0.3845 0.3776 0.3963 0.3744 0.3819 0.3586 0.3702 TO 0.3586 0.3702 0.3744 0.3819 0.3708 0.3657 0.3559 0.3547 TP 0.3559 0.3547 0.3708 0.3657 0.3677 0.3518 0.3539 0.3425 UN 0.347 0.372 0.3610 0.3845 0.3586 0.3702 0.346 0.359 UO 0.346 0.359 0.3586 0.3702 0.3559 0.3547 0.344 0.344 UP 0.344 0.344 0.3559 0.3547 0.3570 0.3425 0.3425 0.3322 NOTE: Tolerance on each color bin(x,y)is±0.01 Page 6/15 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only The C.I.E 1931 Chromaticity Coordinates 0.44 0.42 4100K 4500K 0.40 5000K TN 0.38 UN 0.36 UO TO TP UP 0.34 0.32 0.30 0.32 0.34 0.36 Page 7/15 0.38 0.40 0.42 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Recommended Profile for Reflow Soldering Pb -free solder temperature profile Pb -free solder Temperature profile Pre-heat Pre-heat time Peak-Temperature Soldering time condition 180-200°C 120 Sec Max 260°C Max 10 Sec Max 260°C.Max. 10 Sec .Max. 1-5°C/Sec. 60 Sec.Max. Above220°C 6°C/Sec. Pre-heating 180-200°C 1-5°C/Sec. 120 Sec. Max. (1) Reflow soldering should not be done more than two times. (2) When soldering,do not put stress on the LEDs during heating. (3) After soldering,do not warp the circuit board. (4) The encapsulated material of the LEDs is silicone. Precautions should be taken to avoid the strong pressure on the encapsulated part. So when using the chip mounter,the picking up nozzle that does not affect the silicone resin should be used. Hand Soldering Conditions: Do not exceed 3 seconds at maximum 320°C under soldering iron.(one time only) Page 8/15 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Fig.1 Forward current vs. Forward Voltage Forward Current(mA) 80 60 40 20 0 4.0 5.0 6.0 7.0 8.0 9.0 Forward Voltage(V) Fig.2 Forward current vs.Luminous Intensity Relative Luminous Intensity(%) 1.2 1.0 0.8 0.6 0.4 0.2 0 20 40 Page 9/15 60 80 120 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Fig.3 Luminous Spectrum(Ta=25 °C) Relative Luminous Flux(%) SPECTRAL RADIANCE 100 80 60 40 20 400 500 600 700 800 Wavelength (nm) Fig.4 Directivity Radiation 0° -30° 30° -60° 100% 75% 50% 60° 25% 0 Page 10/15 25% 50% 75% 100% LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Carrier Type Dimensions 4.0 0.25 1.5 1.75 - 5.5 + 12.0±0.3 5.95 9.3 Polarity 4.0 3.25 1.2 Note : The tolerances unless mentioned is ±0.2mm. Packing Specifications Label Aluminum Moist-Proof bag Label Desiccant Page 11/15 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Label Explanation Pb LIGITEK ELECTRONICS CO., LTD. LG-5630WKZ-DT-2-P-NW-D01 PART : LG-5630WKZ-DT-2-P-NW-D01 LOT : GS1-060109 BIN : Luminous Flux GS1-060109 HUE : Chromaticity Coordinates (CIE_x , CIE_y) 1000 QTY(PCS): BIN/HUE : 2000 30-36/3050-3250-O VF:3.0-3.2 F28D/UO VF:6.4-6.6 6.6 - 6.4 : Forward Voltage Reel Dimensions 16.0±1.0 60.2±0.5 178±1 13.5 Page 12/15 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Box Explanation 1. 4 BAG / INNER BOX 2. INNER BOX SIZE : L X W X H 23cm X 8.5cm x 26cm H W L 3. 10 INNER BOXES / CARTON 4. CARTON SIZE : L X W X H 58cm X 34cm x 35cm W L H Page 13/15 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Reliability Test: (1)Test items and results Classification Test Item Test Condition Sample Size Operating Life Test 1.Ta=Under Room Temperature As Per Data Sheet Maximum Rating. 2.If=60mA 3.t=1000 hrs 22 High Temperature Storage Test 1.Ta=105 ℃± 5℃ 2.t= 500 hrs 22 Low Temperature Storage Test 1.Ta=-40 ℃±5℃ 2.t=1000 hrs 22 High Temperature High Humidity Storage Test 1.IR-Reflow In-Board, 2 Times 2.Ta= 8 5℃± 5℃ 3.RH=90 %~95 % 4.t= 500 hrs ±2hrs 22 1.IR-Reflow In-Board,2 times 2.Ta=105 ℃ ±5 ℃ & -40 ℃± 5 ℃ ( 30min) ( 30min) 3.total 100 cycles 22 1.T.Sol=260 ℃±5℃ 2.Dwell Time= 10 Max . 22 1.105 ℃ ~ 25 ℃ ~ - 40 ℃ 30mins 15mins 30mins 2.10 0 Cyeles 22 Endurance Test Thermal Shock Test Environmental Test Reflow Soldering Test Temperature Cycling (2)Criteria for judging the damage Criteria for Judgement Item Symbol Test Conditions Min. Max. Forward Voltage Vf If=60mA - U.S.L x1.2 Reverse Current Ir Vr=5V - U.S.L x2.0 Luminous Intensity Iv If=60mA L.S.L x 0.5 - Page 14/15 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Precautions For Use: Storage time: 1.The operation of Temperatures and RH are : 5 ℃~35℃,RH60%. 2.Once the package is opened, the products should be used within a week. Otherwise, they should be kept in a damp proof box with descanting agent. Considering the tape life, we suggest our customers to use our products within a year(from production date). 3.If opened more than one week in an atmosphere 5 ℃ ~ 35℃,RH60%, they should be treated at 60 ℃±5 ℃for 15hrs. Drive Method: LED is a current operated device, and therefore, requirer some kind of current limiting incorporated into the driver circuit. This current limiting typically takes the form of a current limiting resistor placed in series with the LED. Consider worst case voltage variations than could occur across the current limiting resistor. The forward current should not be allowed to change by more than 40% of its desired value. Circuit model A Circuit model B LED LED (A) Recommended circuit. (B) The difference of brightness between LED could be found due to the VF-IF characteristics of LED. Cleaning: Use alcohol-based cleaning solvents such as isopropyl alcohol to clean the LED. ESD(Electrostatic Discharge): Static Electricity or power surge will damage the LED. Use of a conductive wrist band or anti-electrosatic glove is recommended when handing these LED. All devices, equipment and machinery must be properly grounded. Page 15/15