!LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only 0.2W Power Light LED Pb Lead-Free Parts LG-5630WK-1-T60-C-D711 DATA SHEET DOC. NO : QW0905-LG-5630WK-1-T60-C-D711 REV. : B DATE : 06 - Aug. - 2012 發行 立碁電子 DCC !LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Product Model Designation System LG - 56 30 WK - 1 - T60 - C - D7 11 X1 X2 X3 X4 X5 X6 X7 X8 X9 X1 X2 X3 X4 X5 Title Dimension(L) Dimension(W) Emitting Color Chip Modification LG:Ligitek 57:5.7mm 30:3.0mm WK:White Color -X: 2 chip in 1(Parallel) -1: 1 chip in 1 56:5.6mm -2: 2 chip in 1(Series) X6 X7 X8 X9 Test Conditions Chromaticity Coordinates Color Rendering Index Bin Modification -C: Cool White -D7: CRI>70 -N: Neutral White -D8: CRI>80 T60: @60mA -W: Warm White Page 1/15 !LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Typical Applications Features *. White colored SMTpackage *.Suitable for all SMT assembly and soldering methodes *. Pb-Free Reflow soldering application *. More Energy Efficient than lncandescent and most Halogen lamps. *. RoHS compliant *. Reading Light (car,bus,aircraft) *. Portable(flashlight,bicycle). *. Backlights(Monitor,TV) / Light Guides. *. Automotive Exterior (Stop-Tail-Tum,CHMSL,Mirror Side Repeat). *. Commercial and Residential Architectural lighting. *. Mini-accent / Uplighters / Downlighters / Orientation lighting *. Fiber Optic Alternative / Decorative / Entertainment lighting. *. Security / Garden lighting. *. Cove / Undershelf / Task lighting. *. Traffic signaling / Beacons / Rail crossing and Wayside lighting. Dimension 5.3 C 3.0 A C Recommended Solder Patterns 5.6 2.0 0.9 1.6 1.62 3.8 6.8 0.5 0.8 1.28 0.5 2.1 Slug Anode(+) 0.3 2.3 0.8 Cathode(-) Note: ʳ 1.The tolerance unless mentioned is ±0.1mm,unit=mm. 2.It is strongly recommended to apply on electrically isolated heat conducting film between the slug and contact surfaces. Page 2/15 !LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Absolute Maximum Ratings at Ta=25к Ratings Parameter Symbol UNIT White ʳDC Forward Current IF 60 mA Power Dissipation PD 0.2 W IFP 100 mA LED junction Temperature Tj 125 к Reverse Current(VR=5V) Ir 10 ȝA ʳESD Sensitivity ʳ VB ±500 V Storage Temperature Tstg -40 ~ +100 к Operating Temperature Topr -40 ~ +85 к Soldering Temperature Tp 260 к Peak pulse current ʳDuty 1/10@10KHz ʳ Note: 1.Proper current derating must be observed to maintain temperature below the maximum. 2.LEDS are not designed to be driven in reverse bias. Luminous Intensity Characteristics at 60mA ʳ ʳ(Ratings At 25°C Ambient) PART NO LG-5630WK-1-T60-C-D711 Luminous Intensity Emission Color Min. Typ. Max. White 18 19 ---- Note : 1. White emitters are built with InGaN. 2. Luminous Intensity is measured with an accuracy of ±10% Page 3/15 Units lm !LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Forward Voltage Characteristics at 60mA (Ratings At 25°C Ambient) Vf PART NO Emission Color Min. Typ. Max. LG-5630WK-1-T60-C-D711 White 2.8 ---- 3.6 Units V Note : Forward Voltage is measured with an accuracy of±0.1V Chromaticity Coordinates Characteristics at 60mA (Ratings At 25°C Ambient ) Part No. Emission Color LG-5630WK-1-T60-C-D711 White Chromaticity Coordinates X Y Max. Max. Min. Min. 0.3028 0.3376 0.3113 0.3616 Note : Chromaticity Coordinates is measured with an accuracy of±0.01. Emission Angle Characteristics at 60mA (Ratings At 25°C Ambient ) PART NO Emission Color Lambertian Units LG-5630WK-1-T60-C-D711 White 120 Degrees Color Rendering Index Characteristics at 60mA (Ratings At 25°C Ambient ) CRI PART NO Emission Color Min. Typ. Max. LG-5630WK-1-T60-C-D711 White 70 ---- ---- Page 4/15 !LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Bin Code Description Bin Code Luminous Intensity F18D Luminous Intensity (Lm) @IF=60mA Bin Code Min. Max. F18D 18 20 F20D 20 22 F22D 22 24 F24D 24 26 CIE Forward Voltage 65K-1 3.0-3.1 Color Rank @IF=60mA Forward Voltage(V) @IF=60mA 57K-1 2.8-2.9 57K-2 2.9-3.0 57K-3 3.0-3.1 57K-4 3.1-3.2 65K-1 3.2-3.3 65K-2 3.3-3.4 65K-3 3.4-3.5 65K-4 3.5-3.6 Page 5/15 !LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Bins Code of chromaticity coordinates CCT(K) Reference Range 5310-5700 5700-6020 6020-6500 6500-7040 1 BIN CODE X 2 Y X 3 Y X 4 Y X Y 57K-1 0.3376 0.3616 0.3292 0.3539 0.3293 0.3423 0.3371 0.3493 57K-2 0.3371 0.3493 0.3293 0.3423 0.3294 0.3306 0.3366 0.3369 57K-3 0.3292 0.3539 0.3207 0.3462 0.3215 0.3353 0.3293 0.3423 57K-4 0.3293 0.3423 0.3215 0.3353 0.3222 0.3243 0.3294 0.3306 65K-1 0.3205 0.3481 0.3117 0.3393 0.3131 0.3290 0.3213 0.3371 65K-2 0.3213 0.3371 0.3131 0.3290 0.3145 0.3187 0.3221 0.3261 65K-3 0.3117 0.3393 0.3028 0.3304 0.3048 0.3209 0.3131 0.3290 65K-4 0.3131 0.3290 0.3048 0.3209 0.3068 0.3113 0.3145 0.3187 NOTE: Tolerance on each color bin(x,y)is±0.01 Page 6/15 !LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only The C.I.E 1931 Chromaticity Coordinates 0.38 5310 5700 0.36 6020 6500 0.34 7040 0.32 0.30 0.30 57K-3 57K-2 65K-1 65K-3 57K-1 57K-4 65K-2 65K-4 0.32 0.34 Page 7/15 0.36 !LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Recommended Profile for Reflow Soldering Pb -free solder temperature profile Pb -free solder Temperature profile Pre-heat Pre-heat time Peak-Temperature Soldering time condition 180-200°C 120 Sec Max 260°C Max 10 Sec Max 260°C.Max. 10 Sec .Max. 1-5°C/Sec. 60 Sec.Max. Above220°C 6°C/Sec. Pre-heating 180-200°C 1-5°C/Sec. 120 Sec. Max. (1) Reflow soldering should not be done more than two times. (2) When soldering,do not put stress on the LEDs during heating. (3) After soldering,do not warp the circuit board. (4) The encapsulated material of the LEDs is silicone. Precautions should be taken to avoid the strong pressure on the encapsulated part. So when using the chip mounter,the picking up nozzle that does not affect the silicone resin should be used. Hand Soldering Conditions: Do not exceed 3 seconds at maximum 320°C under soldering iron.(one time only) Page 8/15 !LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Forward Voltage(V) Fig.1 Forward current vs. Forward Voltage Forward Current(mA) Relative Luminous Intensity(%) Fig.2 Forward current vs.Luminous Intensity Forward Current(mA) Page 9/15 !LIGITEK ELECTRONICS CO.,LTD. Relative Luminous Flux(%) Property of Ligitek Only Fig.3 Luminous Spectrum(Ta=25 ̓C) SPECTRAL RADIANCE Wavelength (nm) Fig.4 Directivity Radiation 0̓ -30̓ 30̓ -60̓ 60̓ 100% 75% 50% 25% 0 Page 10/15 25% 50% 75% 100% !LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Carrier Type Dimensions 4.0 0.25 1.5 1.75 - 5.5 + 12.0±0.3 5.95 9.3 Polarity 4.0 3.25 1.2 Note : The tolerances unless mentioned is ̈́0.2mm. Packing Specifications Label Aluminum Moist-Proof bag Label Desiccant Page 11/15 !LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Label Explanation Pb LIGITEK ELECTRONICS CO., LTD. !QBSU!; ! MH.6741XL.2.U71.D.E822 BIN : Luminous Flux !MPU!; ! HT2.17121: HUE : Chromaticity Coordinates (CIE_x , CIE_y) !RUZ)QDT*;! 2111 ! WG;4/1.4/2 !CJO0IVF!;! G29E076L.2 VF : Forward Voltage Reel Dimensions 16.0̈́1.0 60.2±0.5 178±1 13.5 Page 12/15 !LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Box Explanation 1. 4 BAG / INNER BOX 2. INNER BOX SIZE : L X W X H 23cm X 8.5cm x 26cm H W L 3. 10 INNER BOXES / CARTON 4. CARTON SIZE : L X W X H 58cm X 34cm x 35cm W L H Page 13/15 !LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Reliability Test: (1)Test items and results Test Item Classification Test Condition Sample Size Operating Life Test 1.Ta=Under Room Temperature As Per Data Sheet Maximum Rating. 2.If=60mA 3.t=1000 hrs 22 High Temperature Storage Test 1.Ta=105к± 5к 2.t=500 hrs 22 Low Temperature Storage Test 1.Ta=-40к²5к 2.t=1000 hrs 22 High Temperature High Humidity Storage Test 1.IR-Reflow In-Board, 2 Times 2.Ta=85к± 5к 3.RH=90%~95% 4.t=500hrs±2hrs 22 1.IR-Reflow In-Board,2 times 2.Ta=105к ±5к & -40к± 5к (30min) (30min) 3.total 100 cycles 22 1.T.Sol=260к̈́5к 2.Dwell Time= 10Max. 22 1.105к ~ 25к ~ - 40к 30mins 15mins 30mins 2.100 Cyeles 22 Endurance Test Thermal Shock Test Environmental Test Reflow Soldering Test Temperature Cycling (2)Criteria for judging the damage Criteria for Judgement Item Symbol Test Conditions Min. Max. Forward Voltage Vf If=60mA - U.S.L x1.2 Reverse Current Ir Vr=5V - U.S.L x2.0 Luminous Intensity Iv If=60mA L.S.L x 0.5 - Page 14/15 !LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Precautions For Use: Storage time: 1.The operation of Temperatures and RH are : 5 к~35к,RH60%. 2.Once the package is opened, the products should be used within a week. Otherwise, they should be kept in a damp proof box with descanting agent. Considering the tape life, we suggest our customers to use our products within a year(from production date). 3.If opened more than one week in an atmosphere 5 к ~ 35к,RH60%, they should be treated at 60 к±5 кfor 15hrs. Drive Method: LED is a current operated device, and therefore, requirer some kind of current limiting incorporated into the driver circuit. This current limiting typically takes the form of a current limiting resistor placed in series with the LED. Consider worst case voltage variations than could occur across the current limiting resistor. The forward current should not be allowed to change by more than 40% of its desired value. Circuit model A Circuit model B LED LED (A) Recommended circuit. (B) The difference of brightness between LED could be found due to the VF-IF characteristics of LED. Cleaning: Use alcohol-based cleaning solvents such as isopropyl alcohol to clean the LED. ESD(Electrostatic Discharge): Static Electricity or power surge will damage the LED. Use of a conductive wrist band or anti-electrosatic glove is recommended when handing these LED. All devices, equipment and machinery must be properly grounded. Page 15/15