LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only SURFACE MOUNT LED TAPE AND REEL Pb Lead-Free Parts LZIR9553 DATA SHEET DOC. NO : QW0905-LZIR9553 REV. : B DATE : 07 - Apr. - 2016 發行 立碁電子 DCC LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 1/11 PART NO. LZIR9553 Features: 1. Top view LED. 2. white SMT package. 3. Leadframe package with individual 2 pin. 4.Wide viewing angle. 5.Soldering methods:IR reflow soldering. 6.Feature of the device:more light due to higher optical efficiency;extremely wide viewing angle;ideal for backlighting and coupling in light guide. Descriptions: The LZIR9553 SMD has wide viewing angle and optimized light coupling by inter reflector,The low current requirement makes this device ideal for portable equipment or any other application where power is at a premium. Applications: 1. Smoke detector. 2. VCR. 3. Optoelectronic Switch. 4. Sensor. Device Selection Guide: PART NO MATERIAL LENS COLOR LZIR9553 GaAIAs Water Clear LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 2/11 PART NO. LZIR9553 Package Dimensions 3.5 1.85 0.9 0.9 2.8 2.2 Cathode Mark Soldering Terminal 3.2 Andoe 0.9 Cathode Polarity 0.9 Note : 1.All dimension are in millimeter tolerance is ±0.2mm unless otherwise noted. 2.Specifications are subject to change without notice. Recommended Soldering Pad Dimensions 4.5 1.5 1.5 2.6 Note : The tolerances unless mentioned is ±0.1mm,Angle ±0.5. Unit=mm. LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 3/11 PART NO. LZIR9553 Absolute Maximum Ratings at Ta=25℃ Ratings Parameter Symbol UNIT ZIR Power Dissipation PD 100 mW Peak Forward Current (300pps,10μs Pulse) IFP 1 A Forward Current IF 50 mA Reverse Voltage Vr 5 V Operating Temperature Topr - 40 ~ + 85 ℃ Storage Temperature Tstg - 40 ~ + 100 ℃ Typical Electrical & Optical Characteristics (Ta=25℃) SYMBOL Min. Typ. Max. UNIT CONDITION Radiant Intensity Le 1.8 3.2 ---- mW/sr IF=20mA Peak Emission Wavelength λP ---- 810 ---- nm IF=20mA △λ ---- 50 ---- nm IF=20mA Forward Voltage VF 1.2 ---- 1.7 V IF=20mA Reverse Current IR ---- ---- 100 μA VR=5V 2θ 1/2 ---- 120 ---- deg PARAMETER Spectral Line Half Width Viewing Angle Note : 1.The Radiant intensity data did not including ±15% testing tolerance. LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 4/11 PART NO. LZIR9S53 Luminous Intensity Classification BIN CODE Po(mw/sr) at 20mA Min. Max. M 1.8 2.4 N 2.4 3.2 P 3.2 4.2 Q 4.2 5.5 R 5.5 7.2 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LZIR9553 Page 5/11 Typical Electro-Optical Characteristics Curve Relative Radiant Intensity Normalize @20mA ZIR CHIP Forward Current [mA] 1000 100 10 1.0 0.1 0.5 1.0 1.5 2.0 2.5 3.0 3.5 1.0 0.5 0.0 650 4.0 700 900 850 950 Fig.4 Relative Radiant Power vs. Forward Peak Current 10.0 10.0 Relative Radiant Power Normalized @ 100 mA Fig 3. Relative Radiant Power vs. Forward Peak Current 1.0 0.1 1.0 10 100 1.0 0.1 10 100 Fig.6 Relative Radiant Power vs. Temperature 1.2 1.1 1.0 0.9 0.8 -20 0 20 40 60 80 Ambient Temperature [ ℃] 100 Relative Radiant Power @ 20mA, Normalize @ 25 ℃ Fig.5 Forward DC Voltage vs. Temperature -40 1000 IFPK [mA] IFDC [mA] Forw ard DC Voltage @ 20 mA Normalize @ 25 ℃ 800 Wavelength[nm] Forward Voltage[V] Relative Radiant Power Normalized @ 20mA 750 3.0 2.5 2.0 1.5 1.0 0.5 0 -40 -20 0 20 40 60 80 Ambient Temperature [ ℃] 100 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 6/11 PART NO. LZIR9553 Carrier Type Dimensions 4.0 2.0 4.0 2.08 ψ1.5 1.75 3.5 8.0 ±0.3 5.4 3.66 Polarity 3.00 Note : The tolerances unless mentioned is ± 0.1mm,Unit=mm. ‧ Packing Specifications 0.2 0.8 0.6 Aluminum Moist-Proof bag Label 0.8 0.6 0.2 0.4 0.4 Label Part No. Description Quantity/Reel LZIR9553 8.0mm tape,7"reel 2000 PCS LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 7/11 PART NO. LZIR9553 Label Explanation LIGITEK ELECTRONICS CO., LTD. Pb PART : LZIR9553 LOT : GS11640168 QTY(PCS): 2000 BIN/HUE : M BIN : Radiant Intensity Reel Dimensions 0.2 0.4 0.8 0.8 0.6 0.2 0.4 0.6 2.0±0.5 178 ±1.5 6.0 ±1.0 9.0±1.0 ψ13.5±1.0 12.0±1.0 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 8/11 PART NO. LZIR9553 Box Explanation 1. 5 BAG / INNER BOX 2. INNER BOX SIZE : L X W X H 23cm X 8.5cm x 26cm H W L 3. 10 INNER BOXES / CARTON 4. CARTON SIZE : L X W X H 58cm X 34cm x 35cm L W H LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 9/11 PART NO. LZIR9553 Recommended Soldering Conditions 1. Hand Solder Basic spec is ≦ 320℃ 3 sec one time only. 2 PB-Free Reflow Solder 1~5°C/sec 1~5°C/sec Preheat 180~200°C 260°C MaX. 10sec.Max 6°C/sec Above 220°C 60 sec.Max. 120 sec.Max. Note: 1.Reflow soldering should not be done more than two times. 2.When soldering,do not put stress on the LEDs during heating. 3.After soldering,do not warp the circuit board. LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 10/11 PART NO. LZIR9553 Precautions For Use: Storage time: 1. Calculated shelf life before opening is 12 months at < 30°C and < 90% relative humidity (RH) 2. After bag is opened, devices which will be subjected to reflow soldering or other high temperature processes must be a) Assemblied within 168 hours in an environment of ≦ 30°C / 60% RH, or b) Stored at ambient of 10% RH or less 3. Devices are required baking before assembly if: a) Humidity Indicator Card reads >10% (for level 2a -5a) or >60% (for level 2) at ambient temperature 23 ±5°C b) 2.a) or 2.b) doesn't meet 4. If baking is required, devices should be baked for >24 hours at 60±5°C.Performing baking only once, and using the baked devices within 72 hours. Drive Method: LED is a current operated device, and therefore, requirer some kind of current limiting incorporated into the driver circuit. This current limiting typically takes the form of a current limiting resistor placed in series with the LED. Consider worst case voltage variations than could occur across the current limiting resistor. The forwrd current should not be allowed to change by more than 40% of its desired value. Circuit model A Circuit model B LED LED (A) Recommended circuit. (B) The difference of brightness between LED could be found due to the VF-IF characteristics of LED. Cleaning: Use alcohol-based cleaning solvents such as isopropyl alcohol to clean the LED. ESD(Electrostatic Discharge): Static Electricity or power surge will damage the LED. Use of a conductive wrist band or anti-electrosatic glove is recommended when handing these LED. All devices, equipment and machinery must be properly grounded. LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 11/11 PART NO. LZIR9553 Reliability Test: Classification Test Item Test Condition Sample Size Operating Life Test 1.Ta=25°C 2.If=20mA 3.t=1000 hrs (-24hrs,+72hrs) 22 High Temperature Storage Test 1.Ta=100°C±5°C 2.t=1000 hrs (-24hrs,+72hrs) 22 Low Temperature Storage Test 1.Ta=-40°C±5°C 2.t=1000 hrs (-24hrs,+72hrs) 22 High Temperature High Humidity Storage Test 1.Ta=85°C 2.RH=85% 3.t=1000hrs(-24hrs,+72hrs) 22 1.Ta=100°C±5°C ~ -40°C±5°C 20min/ 10sec / 20min 2.total 100 cycles 22 1.100°C±5°C ~ -40°C±5°C 30mins / 5mins / 30mins 2.100 Cyeles 22 Endurance Test Thermal Shock Test Environmental Test Temperature Cycling IR Reflow 1.T=260°C Max. 10sec.Max. 2. 6 Min 22