LM2596 D

LM2596
3.0 A, Step-Down Switching
Regulator
The LM2596 regulator is monolithic integrated circuit ideally suited
for easy and convenient design of a step−down switching regulator
(buck converter). It is capable of driving a 3.0 A load with excellent
line and load regulation. This device is available in adjustable output
version and it is internally compensated to minimize the number of
external components to simplify the power supply design.
Since LM2596 converter is a switch−mode power supply, its
efficiency is significantly higher in comparison with popular
three−terminal linear regulators, especially with higher input voltages.
The LM2596 operates at a switching frequency of 150 kHz thus
allowing smaller sized filter components than what would be needed
with lower frequency switching regulators. Available in a standard
5−lead TO−220 package with several different lead bend options, and
D2PAK surface mount package.
The other features include a guaranteed $4% tolerance on output
voltage within specified input voltages and output load conditions, and
$15% on the oscillator frequency. External shutdown is included,
featuring 80 mA (typical) standby current. Self protection features
include switch cycle−by−cycle current limit for the output switch, as
well as thermal shutdown for complete protection under fault
conditions.
http://onsemi.com
5
Heatsink surface connected to Pin 3
TO−220
T SUFFIX
CASE 314D
1
5
Pin
Features
•
•
•
•
•
•
•
•
•
•
Adjustable Output Voltage Range 1.23 V − 37 V
Guaranteed 3.0 A Output Load Current
Wide Input Voltage Range up to 40 V
150 kHz Fixed Frequency Internal Oscillator
TTL Shutdown Capability
Low Power Standby Mode, typ 80 mA
Thermal Shutdown and Current Limit Protection
Internal Loop Compensation
Moisture Sensitivity Level (MSL) Equals 1
Pb−Free Packages are Available
1
5
November, 2008 − Rev. 0
Vin
Output
Ground
Feedback
ON/OFF
D2PAK
D2T SUFFIX
CASE 936A
ORDERING INFORMATION
Simple High−Efficiency Step−Down (Buck) Regulator
Efficient Pre−Regulator for Linear Regulators
On−Card Switching Regulators
Positive to Negative Converter (Buck−Boost)
Negative Step−Up Converters
Power Supply for Battery Chargers
© Semiconductor Components Industries, LLC, 2008
1.
2.
3.
4.
5.
Heatsink surface (shown as terminal 6 in
case outline drawing) is connected to Pin 3
Applications
•
•
•
•
•
•
TO−220
TV SUFFIX
CASE 314B
1
See detailed ordering and shipping information in the package
dimensions section on page 23 of this data sheet.
DEVICE MARKING INFORMATION
See general marking information in the device marking
section on page 23 of this data sheet.
1
Publication Order Number:
LM2596/D
LM2596
Typical Application (Adjustable Output Voltage Version)
R1
Feedback
12 V
Unregulated
DC Input
+Vin
Cin
100 mF
L1
R2
33 mH 3.1k
4
LM2596
Output
1
3 GND 5
D1
1N5822
2
ON/OFF
1.0k
CFF
5.0 V Regulated
Output 3.0 A Load
Cout
220 mF
Block Diagram
+Vin
Unregulated
DC Input
3.1 V Internal
Regulator
1
ON/OFF
ON/OFF
5
Cin
Feedback
CFF
R2
4
R1
Current
Limit
Fixed Gain
Error Amplifier Comparator
Driver
Latch
Freq
Shift
30 kHz
1.235 V
Band-Gap
Reference
L1
Output
3.0 Amp
Switch
150 kHz
Oscillator
Reset
Thermal
Shutdown
2
GND
Regulated
Output
Vout
D1
3
Cout
Load
Figure 1. Typical Application and Internal Block Diagram
MAXIMUM RATINGS
Symbol
Value
Unit
Maximum Supply Voltage
Rating
Vin
45
V
ON/OFF Pin Input Voltage
−
−0.3 V ≤ V ≤ +Vin
V
Output Voltage to Ground (Steady−State)
−
−1.0
V
PD
Internally Limited
W
Power Dissipation
Case 314B and 314D (TO−220, 5−Lead)
Thermal Resistance, Junction−to−Ambient
RqJA
65
°C/W
Thermal Resistance, Junction−to−Case
RqJC
5.0
°C/W
PD
Internally Limited
W
Thermal Resistance, Junction−to−Ambient
RqJA
70
°C/W
Thermal Resistance, Junction−to−Case
RqJC
5.0
°C/W
Tstg
−65 to +150
°C
Case 936A (D2PAK)
Storage Temperature Range
Minimum ESD Rating (Human Body Model: C = 100 pF, R = 1.5 kW)
−
2.0
kV
Lead Temperature (Soldering, 10 seconds)
−
260
°C
Maximum Junction Temperature
TJ
150
°C
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
http://onsemi.com
2
LM2596
PIN FUNCTION DESCRIPTION
Pin
Symbol
Description (Refer to Figure 1)
1
Vin
This pin is the positive input supply for the LM2596 step−down switching regulator. In order to minimize voltage transients and to supply the switching currents needed by the regulator, a suitable input bypass capacitor must be present
(Cin in Figure 1).
2
Output
This is the emitter of the internal switch. The saturation voltage Vsat of this output switch is typically 1.5 V. It should be
kept in mind that the PCB area connected to this pin should be kept to a minimum in order to minimize coupling to
sensitive circuitry.
3
GND
4
Feedback
This pin is the direct input of the error amplifier and the resistor network R2, R1 is connected externally to allow programming of the output voltage.
5
ON/OFF
It allows the switching regulator circuit to be shut down using logic level signals, thus dropping the total input supply
current to approximately 80 mA. The threshold voltage is typically 1.6 V. Applying a voltage above this value (up to
+Vin) shuts the regulator off. If the voltage applied to this pin is lower than 1.6 V or if this pin is left open, the regulator
will be in the “on” condition.
Circuit ground pin. See the information about the printed circuit board layout.
OPERATING RATINGS (Operating Ratings indicate conditions for which the device is intended to be functional, but do not guarantee
specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics.)
Rating
Symbol
Value
Unit
Operating Junction Temperature Range
TJ
−40 to +125
°C
Supply Voltage
Vin
4.5 to 40
V
http://onsemi.com
3
LM2596
SYSTEM PARAMETERS
ELECTRICAL CHARACTERISTICS Specifications with standard type face are for TJ = 25°C, and those with boldface type apply
over full Operating Temperature Range −40°C to +125°C
Symbol
Characteristics
Min
Typ
Max
Unit
LM2596 (Note 1, Test Circuit Figure 15)
Feedback Voltage (Vin = 12 V, ILoad = 0.5 A, Vout = 5.0 V, )
VFB_nom
Feedback Voltage (8.5 V ≤ Vin ≤ 40 V, 0.5 A ≤ ILoad ≤ 3.0 A, Vout = 5.0 V)
VFB
1.193
1.18
η
−
Symbol
Min
Efficiency (Vin = 12 V, ILoad = 3.0 A, Vout = 5.0 V)
Characteristics
1.23
Feedback Bias Current (Vout = 5.0 V)
Ib
1.267
1.28
V
73
−
%
Typ
Max
Unit
25
100
200
nA
150
165
180
kHz
1.8
2.0
V
Oscillator Frequency (Note 2)
fosc
Saturation Voltage (Iout = 3.0 A, Notes 3 and 4)
Vsat
1.5
Max Duty Cycle “ON” (Note 4)
DC
95
Current Limit (Peak Current, Notes 2 and 3)
ICL
Output Leakage Current (Notes 5 and 6)
Output = 0 V
Output = −1.0 V
IL
Quiescent Current (Note 5)
Standby Quiescent Current (ON/OFF Pin = 5.0 V (“OFF”))
(Note 6)
135
120
4.2
3.5
V
%
5.6
6.9
7.5
A
0.5
6.0
2.0
20
IQ
5.0
10
mA
Istby
80
200
250
mA
mA
ON/OFF PIN LOGIC INPUT
1.6
Threshold Voltage
Vout = 0 V (Regulator OFF)
VIH
Vout = Nominal Output Voltage (Regulator ON)
VIL
V
2.2
2.4
V
1.0
0.8
V
ON/OFF Pin Input Current
ON/OFF Pin = 5.0 V (Regulator OFF)
IIH
−
15
30
mA
ON/OFF Pin = 0 V (regulator ON)
IIL
−
0.01
5.0
mA
1. External components such as the catch diode, inductor, input and output capacitors can affect switching regulator system performance.
When the LM2596 is used as shown in the Figure 15 test circuit, system performance will be as shown in system parameters section.
2. The oscillator frequency reduces to approximately 30 kHz in the event of an output short or an overload which causes the regulated output
voltage to drop approximately 40% from the nominal output voltage. This self protection feature lowers the average dissipation of the IC by
lowering the minimum duty cycle from 5% down to approximately 2%.
3. No diode, inductor or capacitor connected to output (Pin 2) sourcing the current.
4. Feedback (Pin 4) removed from output and connected to 0 V.
5. Feedback (Pin 4) removed from output and connected to +12 V to force the output transistor “off”.
6. Vin = 40 V.
http://onsemi.com
4
LM2596
TYPICAL PERFORMANCE CHARACTERISTICS (Circuit of Figure 15)
1.4
Vout , OUTPUT VOLTAGE CHANGE (%)
Vout , OUTPUT VOLTAGE CHANGE (%)
1.0
Vin = 20 V
ILoad = 500 mA
Normalized at TJ = 25°C
0.8
0.6
0.4
0.2
0
-0.2
-0.4
-0.6
-0.8
-1.0
-50
-25
0
25
50
75
100
1.2
0.8
0.4
0.2
-0.2
-0.4
0
5.0
10
15
20
25
30
TJ, JUNCTION TEMPERATURE (°C)
Vin, INPUT VOLTAGE (V)
Figure 2. Normalized Output Voltage
Figure 3. Line Regulation
35
40
6.0
Vin = 25 V
I O, OUTPUT CURRENT (A)
ILoad = 3.0 A
1.5
1.0
ILoad = 500 mA
0.5
5.5
5.0
4.5
L1 = 33 mH
Rind = 0.1 W
0
-50
-25
0
25
50
75
100
4.0
-50
125
16
14
ILoad = 3.0 A
12
10
ILoad = 200 mA
6.0
5.0
50
75
100
Figure 5. Current Limit
Vout = 5.0 V
Measured at
Ground Pin
TJ = 25°C
0
25
Figure 4. Dropout Voltage
18
4.0
0
TJ, JUNCTION TEMPERATURE (°C)
20
8.0
-25
TJ, JUNCTION TEMPERATURE (°C)
I stby , STANDBY QUIESCENT CURRENT (μA)
INPUT - OUTPUT DIFFERENTIAL (V)
12 V and 15 V
0
2.0
I Q, QUIESCENT CURRENT (mA)
3.3 V and 5.0 V
0.6
-0.6
125
ILoad = 500 mA
TJ = 25°C
1.0
10
15
20
25
30
35
40
200
180
VON/OFF = 5.0 V
160
140
Vin = 40 V
120
100
80
Vin = 12 V
60
40
20
0
-50
-25
0
25
50
75
100
Vin, INPUT VOLTAGE (V)
TJ, JUNCTION TEMPERATURE (°C)
Figure 6. Quiescent Current
Figure 7. Standby Quiescent Current
http://onsemi.com
5
125
125
LM2596
200
1.6
180
Vsat , SATURATION VOLTAGE (V)
I stby , STANDBY QUIESCENT CURRENT (μA)
TYPICAL PERFORMANCE CHARACTERISTICS (Circuit of Figure 15)
160
TJ = 25°C
140
120
100
80
60
40
20
0
1.4
1.2
-40°C
1.0
0.8 25°C
0.6
125°C
0.4
0.2
0
0
5
10
15
20
25
35
30
40
0
0.5
1.0
Vin, INPUT VOLTAGE (V)
3.0
Figure 9. Switch Saturation Voltage
1.0
NORMALIZED FREQUENCY (%)
2.5
2.0
SWITCH CURRENT (A)
Figure 8. Standby Quiescent Current
5.0
VIN = 12 V Normalized
at 25°C
0.0
4.5
V in, INPUT VOLTAGE (V)
−1.0
−2.0
−3.0
−4.0
−5.0
−6.0
−7.0
−8.0
4.0
3.5
3.0
2.5
2.0
Vout ' 1.23 V
ILoad = 500 mA
1.5
1.0
0.5
−25
0
25
50
75
100
0
-50
125
-25
TJ, JUNCTION TEMPERATURE (°C)
0
25
80
60
40
20
0
-20
-40
-60
-80
-25
75
100
TJ, JUNCTION TEMPERATURE (°C)
100
-100
-50
50
Figure 11. Minimum Supply Operating Voltage
Figure 10. Switching Frequency
Ib , FEEDBACK PIN CURRENT (nA)
−9.0
−50
1.5
0
25
50
75
100
TJ, JUNCTION TEMPERATURE (°C)
Figure 12. Feedback Pin Current
http://onsemi.com
6
125
125
LM2596
TYPICAL PERFORMANCE CHARACTERISTICS (Circuit of Figure 15)
A
10 V
100 mV
Output
0
Voltage
Change
- 100 mV
0
4.0 A
B
2.0 A
0
C
D
4.0 A
3.0 A
2.0 A
Load 2.0 A
Current
1.0 A
0
0
2 ms/div
100 ms/div
Figure 13. Switching Waveforms
Figure 14. Load Transient Response
Vout = 5 V
A: Output Pin Voltage, 10 V/div
B: Switch Current, 2.0 A/div
C: Inductor Current, 2.0 A/div, AC−Coupled
D: Output Ripple Voltage, 50 mV/div, AC−Coupled
Horizontal Time Base: 5.0 ms/div
Adjustable Output Voltage Versions
Feedback
Vin
LM2596
1
L1
33 mH
Output
3
8.5 V - 40 V
Unregulated
DC Input
4
GND
5
Vout
5,000 V
2
ON/OFF
CFF
Cin
100 mF
D1
1N5822
Cout
220 mF
R2
Load
R1
V out + V
ǒ
R2 + R1
ǒ1.0 ) R2
Ǔ
R1
ref
Ǔ
V out
1.0
V
ref
Where Vref = 1.23 V, R1
between 1.0 k and 5.0 k
Figure 15. Typical Test Circuit
http://onsemi.com
7
LM2596
PCB LAYOUT GUIDELINES
On the other hand, the PCB area connected to the Pin 2
As in any switching regulator, the layout of the printed
(emitter of the internal switch) of the LM2596 should be
circuit board is very important. Rapidly switching currents
kept to a minimum in order to minimize coupling to sensitive
associated with wiring inductance, stray capacitance and
circuitry.
parasitic inductance of the printed circuit board traces can
Another sensitive part of the circuit is the feedback. It is
generate voltage transients which can generate
important to keep the sensitive feedback wiring short. To
electromagnetic interferences (EMI) and affect the desired
assure this, physically locate the programming resistors near
operation. As indicated in the Figure 15, to minimize
to the regulator, when using the adjustable version of the
inductance and ground loops, the length of the leads
LM2596 regulator.
indicated by heavy lines should be kept as short as possible.
For best results, single−point grounding (as indicated) or
ground plane construction should be used.
DESIGN PROCEDURE
Buck Converter Basics
This period ends when the power switch is once again
turned on. Regulation of the converter is accomplished by
varying the duty cycle of the power switch. It is possible to
describe the duty cycle as follows:
The LM2596 is a “Buck” or Step−Down Converter which
is the most elementary forward−mode converter. Its basic
schematic can be seen in Figure 16.
The operation of this regulator topology has two distinct
time periods. The first one occurs when the series switch is
on, the input voltage is connected to the input of the inductor.
The output of the inductor is the output voltage, and the
rectifier (or catch diode) is reverse biased. During this
period, since there is a constant voltage source connected
across the inductor, the inductor current begins to linearly
ramp upwards, as described by the following equation:
I L(on) +
t
d + on , where T is the period of switching.
T
For the buck converter with ideal components, the duty
cycle can also be described as:
V
d + out
V in
Figure 17 shows the buck converter, idealized waveforms
of the catch diode voltage and the inductor current.
ǒV IN * VOUTǓton
Von(SW)
L
Power
Switch
Diode Voltage
During this “on” period, energy is stored within the core
material in the form of magnetic flux. If the inductor is
properly designed, there is sufficient energy stored to carry
the requirements of the load during the “off” period.
L
Vin
Cout
D
Power
Switch
Off
VD(FWD)
Power
Switch
On
Power
Switch
On
RLoad
Time
Figure 16. Basic Buck Converter
Inductor Current
Ipk
The next period is the “off” period of the power switch.
When the power switch turns off, the voltage across the
inductor reverses its polarity and is clamped at one diode
voltage drop below ground by the catch diode. The current
now flows through the catch diode thus maintaining the load
current loop. This removes the stored energy from the
inductor. The inductor current during this time is:
I L(off) +
Power
Switch
Off
ILoad(AV)
Imin
Diode
Power
Switch
Diode
Power
Switch
Time
Figure 17. Buck Converter Idealized Waveforms
ǒV OUT * VDǓtoff
L
http://onsemi.com
8
LM2596
PROCEDURE (ADJUSTABLE OUTPUT VERSION: LM2596)
Procedure
Example
Given Parameters:
Vout = Regulated Output Voltage
Vin(max) = Maximum DC Input Voltage
ILoad(max) = Maximum Load Current
Given Parameters:
Vout = 5.0 V
Vin(max) = 12 V
ILoad(max) = 3.0 A
1. Programming Output Voltage
To select the right programming resistor R1 and R2 value (see
Figure 1) use the following formula:
1. Programming Output Voltage (selecting R1 and R2)
Select R1 and R2:
ǒ
Ǔ
R2
1.0 )
V out + V
ref
R1
ǒ
V out + 1.23 1.0 )
ǒ
where Vref = 1.23 V
R2 + R1
Resistor R1 can be between 1.0 k and 5.0 kW. (For best
temperature coefficient and stability with time, use 1% metal
film resistors).
ǒV
R2 + R1
V out
ref
* 1.0
V out
V
ref
Ǔ
R2
R1
Select R1 = 1.0 kW
Ǔ ǒ
* 1.0
+
Ǔ
5V
* 1.0
1.23 V
R2 = 3.0 kW, choose a 3.0k metal film resistor.
Ǔ
2. Input Capacitor Selection (Cin)
To prevent large voltage transients from appearing at the input
and for stable operation of the converter, an aluminium or
tantalum electrolytic bypass capacitor is needed between the
input pin +Vin and ground pin GND This capacitor should be
located close to the IC using short leads. This capacitor should
have a low ESR (Equivalent Series Resistance) value.
2. Input Capacitor Selection (Cin)
A 100 mF, 50 V aluminium electrolytic capacitor located near
the input and ground pin provides sufficient bypassing.
For additional information see input capacitor section in the
“Application Information” section of this data sheet.
3. Catch Diode Selection (D1)
A. Since the diode maximum peak current exceeds the
regulator maximum load current the catch diode current
rating must be at least 1.2 times greater than the maximum
load current. For a robust design, the diode should have a
current rating equal to the maximum current limit of the
LM2596 to be able to withstand a continuous output short.
B. The reverse voltage rating of the diode should be at least
1.25 times the maximum input voltage.
3. Catch Diode Selection (D1)
A. For this example, a 3.0 A current rating is adequate.
B. For robust design use a 30 V 1N5824 Schottky diode or
any suggested fast recovery diode in the Table 2.
http://onsemi.com
9
LM2596
PROCEDURE (ADJUSTABLE OUTPUT VERSION: LM2596) (CONTINUED)
Procedure
Example
4. Inductor Selection (L1)
A. Calculate E x T [V x ms] constant:
4. Inductor Selection (L1)
A. Use the following formula to calculate the inductor Volt x
microsecond [V x ms] constant:
E
ǒ
T+ V
IN
*V
OUT
*V
Ǔ
SAT
V
V
IN
OUT
*V
)V
SAT
D
)V
1000
D
150 kHz
ǒV
+I
)
T + ǒ12 * 5 * 1.5Ǔ
E
T + ǒ5.5Ǔ
msǓ
B. Match the calculated E x T value with the corresponding
number on the vertical axis of the Inductor Value Selection
Guide shown in Figure 18. This E x T constant is a
measure of the energy handling capability of an inductor and
is dependent upon the type of core, the core area, the
number of turns, and the duty cycle.
C. Next step is to identify the inductance region intersected by
the E x T value and the maximum load current value on the
horizontal axis shown in Figure 18.
D. Select an appropriate inductor from Table 3.
The inductor chosen must be rated for a switching
frequency of 150 kHz and for a current rating of 1.15 x ILoad.
The inductor current rating can also be determined by
calculating the inductor peak current:
I
E
5.5
7.5
5 ) 0.5
1000
12 * 5 ) 0.5
150 kHz
6.6ǒV
ǒV
msǓ
B. E x T = 27 [V x ms]
C. ILoad(max) = 3.0 A
Inductance Region = L40
D. Proper inductor value = 33 mH
Choose the inductor from Table 3.
ǒVin * VoutǓ ton
p(max) Load(max)
2L
where ton is the “on” time of the power switch and
V
t on + out x 1.0
V
f osc
in
5. Output Capacitor Selection (Cout)
A. Since the LM2596 is a forward−mode switching regulator
with voltage mode control, its open loop has 2−pole−1−zero
frequency characteristic. The loop stability is determined by
the output capacitor (capacitance, ESR) and inductance
values.
5. Output Capacitor Selection (Cout)
A. In this example is recommended Nichicon PM
capacitors: 470 mF/35 V or 220 mF/35 V
For stable operation use recommended values of the output
capacitors in Table 1.
Low ESR electrolytic capacitors between 220uFand 1500uF
provide best results.
B. The capacitors voltage rating should be at least 1.5 times
greater than the output voltage, and often much higher
voltage rating is needed to satisfy low ESR requirement
6. Feedforward Capacitor (CFF)
It provides additional stability mainly for higher input voltages. For
Cff selection use Table 1. The compensation capacitor between
0.6 nF and 40 nF is wired in parallel with the output voltage setting
resistor R2, The capacitor type can be ceramic, plastic, etc..
6. Feedforward Capacitor (CFF)
In this example is recommended feedforward capacitor
15 nF or 5 nF.
http://onsemi.com
10
msǓ
LM2596
LM2596 Series Buck Regulator Design Procedures (continued)
Table 1. RECOMMENDED VALUES OF THE OUTPUT CAPACITOR AND FEEDFORWARD CAPACITOR
(Iload = 3 A)
Nichicon PM Capacitors
Vin (V)
Capacity/Voltage Range/ESR (mF/V/mW)
40
1500/35/24
1000/35/29
1000/35/29
680/35/36
560/25/55
560/25/55
470/35/46
26
1200/35/26
820/35
680/35/36
560/35/41
470/25/65
470/25/65
330/35/60
22
1000/35/29
680/35/36
560/35/41
330/25/85
330/25/85
220/35/85
20
820/35/32
470/35/46
470/25/65
330/25/85
330/25/85
220/35/85
18
820/35/32
470/35/46
470/25/65
330/25/85
330/25/85
220/35/85
12
820/35/32
470/35/46
220/35/85
220/25/111
10
820/35/32
470/35/46
220/35/85
Vout (V)
2
4
6
9
12
15
24
28
CFF (nF]
40
15
5
2
1.5
1
0.6
0.6
70
60
L27
L42
L35
220uH
50
L43
L36
L27
470/35/46
L44
L37
40
150uH
30
25
L29
L38
100uH
L30
E*T(V*us)
68uH
L39
L31
20
47uH
L21
15
L40
L32
33uH
L40
L40
L22
22uH
10
9
8
L23
L34
L24
7
6
15uH
L25
L15
5
4
0.6
0.8
1.0
1.5
2.0
2.5
Maximum load current (A)
Figure 18. Inductor Value Selection Guides (For Continuous Mode Operation)
http://onsemi.com
11
3.0
LM2596
Table 2. DIODE SELECTION
Schottky
3.0 A
Fast Recovery
4.0 − 6.0 A
3.0 A
Through
Hole
Surface
Mount
Through
Hole
20 V
1N5820
MBR320P
SR302
SK32
1N5823
SR502
SB520
30 V
1N5821
MBR330
SR303
31DQ03
SK33
30WQ03
1N5824
SR503
SB530
50WQ03
1N5822
MBR340
SR304
31DQ04
SK34
30WQ04
MBRS340T3
MBRD340
1N5825
SR504
SB540
MBRD640CT
50WQ04
50 V
MBR350
31DQ05
SR305
SK35
30WQ05
SB550
50WQ05
60 V
MBR360
DQ06
SR306
MBRS360T3
MBRD360
50SQ080
MBRD660CT
VR
40 V
NOTE:
Surface
Mount
Through
Hole
Surface
Mount
Through
Hole
Surface
Mount
MUR320
31DF1
HER302
MURS320T3
MURD320
30WF10
MUR420
HER602
MURD620CT
50WF10
(all diodes
rated
to at least
100 V)
(all diodes
rated
to at least
100 V)
(all diodes
rated
to at least
100 V)
(all diodes
rated
to at least
100 V)
Diodes listed in bold are available from ON Semiconductor.
http://onsemi.com
12
4.0 − 6.0 A
LM2596
Table 3. INDUCTOR MANUFACTURERS PART NUMBERS
Schott
Renco
Pulse Engineering
Coilcraft
Inductance
(mH)
Current
(A)
Through
Hole
Surface
Mount
Through
Hole
Surface
Mount
Through
Hole
Surface
Mount
Surface Mount
L15
22
0.99
67148350
67148460
RL−1284−22−43
RL1500−2
2
PE−53815
PE−53815−S
DO3308−223
L21
68
0.99
67144070
67144450
RL−5471−5
RL1500−6
8
PE−53821
PE−53821−S
DO3316−683
L22
47
1.17
67144080
67144460
RL−5471−6
−
PE−53822
PE−53822−S
DO3316−473
L23
33
1.40
67144090
67144470
RL−5471−7
−
PE−53823
PE−53823−S
DO3316−333
L24
22
1.70
67148370
67148480
RL−1283−22−43
−
PE−53824
PE−53825−S
DO3316−223
L25
15
2.10
67148380
67148490
RL−1283−15−43
−
PE−53825
PE−53824−S
DO3316−153
L26
330
0.80
67144100
67144480
RL−5471−1
−
PE−53826
PE−53826−S
DO5022P−334
L27
220
1.00
67144110
67144490
RL−5471−2
−
PE−53827
PE−53827−S
DO5022P−224
L28
150
1.20
67144120
67144500
RL−5471−3
−
PE−53828
PE−53828−S
DO5022P−154
L29
100
1.47
67144130
67144510
RL−5471−4
−
PE−53829
PE−53829−S
DO5022P−104
L30
68
1.78
67144140
67144520
RL−5471−5
−
PE−53830
PE−53830−S
DO5022P−683
L31
47
2.20
67144150
67144530
RL−5471−6
−
PE−53831
PE−53831−S
DO5022P−473
L32
33
2.50
67144160
67144540
RL−5471−7
−
PE−53932
PE−53932−S
DO5022P−333
L33
22
3.10
67148390
67148500
RL−1283−22−43
−
PE−53933
PE−53933−S
DO5022P−223
L34
15
3.40
67148400
67148790
RL−1283−15−43
−
PE−53934
PE−53934−S
DO5022P−153
L35
220
1.70
67144170
−
RL−5473−1
−
PE−53935
PE−53935−S
−
L36
150
2.10
67144180
−
RL−5473−4
−
PE−54036
PE−54036−S
−
L37
100
2.50
67144190
−
RL−5472−1
−
PE−54037
PE−54037−S
−
L38
68
3.10
67144200
−
RL−5472−2
−
PE−54038
PE−54038−S
DO5040H−683ML
L39
47
3.50
67144210
−
RL−5472−3
−
PE−54039
PE−54039−S
DO5040H−473ML
L40
33
3.50
67144220
67148290
RL−5472−4
−
PE−54040
PE−54040−S
DO5040H−333ML
L41
22
3.50
67144230
67148300
RL−5472−5
−
PE−54041
PE−54041−S
DO5040H−223ML
L42
150
2.70
67148410
−
RL−5473−4
−
PE−54042
PE−54042−S
−
L43
100
3.40
67144240
−
RL−5473−2
−
PE−54043
-
L44
68
3.40
67144250
−
RL−5473−3
−
PE−54044
DO5040H−683ML
http://onsemi.com
13
LM2596
APPLICATION INFORMATION
EXTERNAL COMPONENTS
regulator loop stability. The ESR of the output capacitor and
the peak−to−peak value of the inductor ripple current are the
main factors contributing to the output ripple voltage value.
Standard aluminium electrolytics could be adequate for
some applications but for quality design, low ESR types are
recommended.
An aluminium electrolytic capacitor’s ESR value is
related to many factors such as the capacitance value, the
voltage rating, the physical size and the type of construction.
In most cases, the higher voltage electrolytic capacitors have
lower ESR value. Often capacitors with much higher
voltage ratings may be needed to provide low ESR values
that, are required for low output ripple voltage.
Input Capacitor (Cin)
The Input Capacitor Should Have a Low ESR
For stable operation of the switch mode converter a low
ESR (Equivalent Series Resistance) aluminium or solid
tantalum bypass capacitor is needed between the input pin
and the ground pin, to prevent large voltage transients from
appearing at the input. It must be located near the regulator
and use short leads. With most electrolytic capacitors, the
capacitance value decreases and the ESR increases with
lower temperatures. For reliable operation in temperatures
below −25°C larger values of the input capacitor may be
needed. Also paralleling a ceramic or solid tantalum
capacitor will increase the regulator stability at cold
temperatures.
Feedfoward Capacitor
(Adjustable Output Voltage Version)
This capacitor adds lead compensation to the feedback
loop and increases the phase margin for better loop stability.
For CFF selection, see the design procedure section.
RMS Current Rating of Cin
The important parameter of the input capacitor is the RMS
current rating. Capacitors that are physically large and have
large surface area will typically have higher RMS current
ratings. For a given capacitor value, a higher voltage
electrolytic capacitor will be physically larger than a lower
voltage capacitor, and thus be able to dissipate more heat to
the surrounding air, and therefore will have a higher RMS
current rating. The consequence of operating an electrolytic
capacitor beyond the RMS current rating is a shortened
operating life. In order to assure maximum capacitor
operating lifetime, the capacitor’s RMS ripple current rating
should be:
The Output Capacitor Requires an ESR Value
That Has an Upper and Lower Limit
As mentioned above, a low ESR value is needed for low
output ripple voltage, typically 1% to 2% of the output
voltage. But if the selected capacitor’s ESR is extremely low
(below 0.05 W), there is a possibility of an unstable feedback
loop, resulting in oscillation at the output. This situation can
occur when a tantalum capacitor, that can have a very low
ESR, is used as the only output capacitor.
At Low Temperatures, Put in Parallel Aluminium
Electrolytic Capacitors with Tantalum Capacitors
Irms > 1.2 x d x ILoad
Electrolytic capacitors are not recommended for
temperatures below −25°C. The ESR rises dramatically at
cold temperatures and typically rises 3 times at −25°C and
as much as 10 times at −40°C. Solid tantalum capacitors
have much better ESR spec at cold temperatures and are
recommended for temperatures below −25°C. They can be
also used in parallel with aluminium electrolytics. The value
of the tantalum capacitor should be about 10% or 20% of the
total capacitance. The output capacitor should have at least
50% higher RMS ripple current rating at 150 kHz than the
peak−to−peak inductor ripple current.
where d is the duty cycle, for a buck regulator
V
t
d + on + out
T
V in
|V out|
t on
and d +
+
for a buck*boost regulator.
T
|V out| ) V
in
Output Capacitor (Cout)
For low output ripple voltage and good stability, low ESR
output capacitors are recommended. An output capacitor
has two main functions: it filters the output and provides
http://onsemi.com
14
LM2596
Catch Diode
Locate the Catch Diode Close to the LM2596
The LM2596 is a step−down buck converter; it requires a
fast diode to provide a return path for the inductor current
when the switch turns off. This diode must be located close
to the LM2596 using short leads and short printed circuit
traces to avoid EMI problems.
Use a Schottky or a Soft Switching
Ultra−Fast Recovery Diode
Since the rectifier diodes are very significant sources of
losses within switching power supplies, choosing the
rectifier that best fits into the converter design is an
important process. Schottky diodes provide the best
performance because of their fast switching speed and low
forward voltage drop.
They provide the best efficiency especially in low output
voltage applications (5.0 V and lower). Another choice
could be Fast−Recovery, or Ultra−Fast Recovery diodes. It
has to be noted, that some types of these diodes with an
abrupt turnoff characteristic may cause instability or
EMI troubles.
A fast−recovery diode with soft recovery characteristics
can better fulfill some quality, low noise design requirements.
Table 2 provides a list of suitable diodes for the LM2596
regulator. Standard 50/60 Hz rectifier diodes, such as the
1N4001 series or 1N5400 series are NOT suitable.
VERTRICAL RESOLUTION 1.0 A/DIV
ripple voltage. On the other hand it does require larger
inductor values to keep the inductor current flowing
continuously, especially at low output load currents and/or
high input voltages.
To simplify the inductor selection process, an inductor
selection guide for the LM2596 regulator was added to this
data sheet (Figure 18). This guide assumes that the regulator
is operating in the continuous mode, and selects an inductor
that will allow a peak−to−peak inductor ripple current to be
a certain percentage of the maximum design load current.
This percentage is allowed to change as different design load
currents are selected. For light loads (less than
approximately 300 mA) it may be desirable to operate the
regulator in the discontinuous mode, because the inductor
value and size can be kept relatively low. Consequently, the
percentage of inductor peak−to−peak current increases. This
discontinuous mode of operation is perfectly acceptable for
this type of switching converter. Any buck regulator will be
forced to enter discontinuous mode if the load current is light
enough.
2.0 A
Inductor
Current
Waveform 0 A
Inductor
2.0 A
Power
Switch
Current
Waveform 0 A
The magnetic components are the cornerstone of all
switching power supply designs. The style of the core and
the winding technique used in the magnetic component’s
design has a great influence on the reliability of the overall
power supply.
Using an improper or poorly designed inductor can cause
high voltage spikes generated by the rate of transitions in
current within the switching power supply, and the
possibility of core saturation can arise during an abnormal
operational mode. Voltage spikes can cause the
semiconductors to enter avalanche breakdown and the part
can instantly fail if enough energy is applied. It can also
cause significant RFI (Radio Frequency Interference) and
EMI (Electro−Magnetic Interference) problems.
HORIZONTAL TIME BASE: 2.0 ms/DIV
Figure 19. Continuous Mode Switching Current
Waveforms
Selecting the Right Inductor Style
Some important considerations when selecting a core type
are core material, cost, the output power of the power supply,
the physical volume the inductor must fit within, and the
amount of EMI (Electro−Magnetic Interference) shielding
that the core must provide. The inductor selection guide
covers different styles of inductors, such as pot core, E−core,
toroid and bobbin core, as well as different core materials
such as ferrites and powdered iron from different
manufacturers.
For high quality design regulators the toroid core seems to
be the best choice. Since the magnetic flux is contained
within the core, it generates less EMI, reducing noise
problems in sensitive circuits. The least expensive is the
bobbin core type, which consists of wire wound on a ferrite
rod core. This type of inductor generates more EMI due to
the fact that its core is open, and the magnetic flux is not
contained within the core.
When multiple switching regulators are located on the
same printed circuit board, open core magnetics can cause
Continuous and Discontinuous Mode of Operation
The LM2596 step−down converter can operate in both the
continuous and the discontinuous modes of operation. The
regulator works in the continuous mode when loads are
relatively heavy, the current flows through the inductor
continuously and never falls to zero. Under light load
conditions, the circuit will be forced to the discontinuous
mode when inductor current falls to zero for certain period
of time (see Figure 19 and Figure 20). Each mode has
distinctively different operating characteristics, which can
affect the regulator performance and requirements. In many
cases the preferred mode of operation is the continuous
mode. It offers greater output power, lower peak currents in
the switch, inductor and diode, and can have a lower output
http://onsemi.com
15
LM2596
interference between two or more of the regulator circuits,
especially at high currents due to mutual coupling. A toroid,
pot core or E−core (closed magnetic structure) should be
used in such applications.
inductor and/or the LM2596. Different inductor types have
different saturation characteristics, and this should be kept
in mind when selecting an inductor.
Exceeding an inductor’s maximum current rating may
cause the inductor to overheat because of the copper wire
losses, or the core may saturate. Core saturation occurs when
the flux density is too high and consequently the cross
sectional area of the core can no longer support additional
lines of magnetic flux.
This causes the permeability of the core to drop, the
inductance value decreases rapidly and the inductor begins
to look mainly resistive. It has only the DC resistance of the
winding. This can cause the switch current to rise very
rapidly and force the LM2596 internal switch into
cycle−by−cycle current limit, thus reducing the DC output
load current. This can also result in overheating of the
VERTICAL RESOLUTION 200 mA/DIV
Do Not Operate an Inductor Beyond its
Maximum Rated Current
0.4 A
Inductor
Current
Waveform
0A
0.4 A
Power
Switch
Current
Waveform
0A
HORIZONTAL TIME BASE: 2.0 ms/DIV
Figure 20. Discontinuous Mode Switching Current
Waveforms
GENERAL RECOMMENDATIONS
Output Voltage Ripple and Transients
Source of the Output Ripple
Minimizing the Output Ripple
In order to minimize the output ripple voltage it is possible
to enlarge the inductance value of the inductor L1 and/or to
use a larger value output capacitor. There is also another way
to smooth the output by means of an additional LC filter (20
mH, 100 mF), that can be added to the output (see Figure 30)
to further reduce the amount of output ripple and transients.
With such a filter it is possible to reduce the output ripple
voltage transients 10 times or more. Figure 21 shows the
difference between filtered and unfiltered output waveforms
of the regulator shown in Figure 30.
The lower waveform is from the normal unfiltered output
of the converter, while the upper waveform shows the output
ripple voltage filtered by an additional LC filter.
Since the LM2596 is a switch mode power supply
regulator, its output voltage, if left unfiltered, will contain a
sawtooth ripple voltage at the switching frequency. The
output ripple voltage value ranges from 0.5% to 3% of the
output voltage. It is caused mainly by the inductor sawtooth
ripple current multiplied by the ESR of the output capacitor.
Short Voltage Spikes and How to Reduce Them
The regulator output voltage may also contain short
voltage spikes at the peaks of the sawtooth waveform (see
Figure 21). These voltage spikes are present because of the
fast switching action of the output switch, and the parasitic
inductance of the output filter capacitor. There are some
other important factors such as wiring inductance, stray
capacitance, as well as the scope probe used to evaluate these
transients, all these contribute to the amplitude of these
spikes. To minimize these voltage spikes, low inductance
capacitors should be used, and their lead lengths must be
kept short. The importance of quality printed circuit board
layout design should also be highlighted.
Heatsinking and Thermal Considerations
The Through−Hole Package TO−220
The LM2596 is available in two packages, a 5−pin
TO−220(T, TV) and a 5−pin surface mount D2PAK(D2T).
Although the TO−220(T) package needs a heatsink under
most conditions, there are some applications that require no
heatsink to keep the LM2596 junction temperature within
the allowed operating range. Higher ambient temperatures
require some heat sinking, either to the printed circuit (PC)
board or an external heatsink.
Voltage spikes
caused by
switching action
of the output
switch and the
parasitic
inductance of the
output capacitor
The Surface Mount Package D 2PAK and its
Heatsinking
The other type of package, the surface mount D2PAK, is
designed to be soldered to the copper on the PC board. The
copper and the board are the heatsink for this package and
the other heat producing components, such as the catch
diode and inductor. The PC board copper area that the
package is soldered to should be at least 0.4 in2 (or 260 mm2)
and ideally should have 2 or more square inches (1300 mm2)
of 0.0028 inch copper. Additional increases of copper area
beyond approximately 6.0 in2 (4000 mm2) will not improve
VERTRICAL
RESOLUTION
20 mV/DIV
Filtered
Output
Voltage
Unfiltered
Output
Voltage
HORIZONTAL TIME BASE: 5.0 ms/DIV
Figure 21. Output Ripple Voltage Waveforms
http://onsemi.com
16
LM2596
VO is the regulator output voltage,
ILoad is the load current.
The dynamic switching losses during turn−on and
turn−off can be neglected if proper type catch diode is used.
heat dissipation significantly. If further thermal
improvements are needed, double sided or multilayer PC
boards with large copper areas should be considered. In
order to achieve the best thermal performance, it is highly
recommended to use wide copper traces as well as large
areas of copper in the printed circuit board layout. The only
exception to this is the OUTPUT (switch) pin, which should
not have large areas of copper (see page 8 ‘PCB Layout
Guideline’).
Packages Not on a Heatsink (Free−Standing)
For a free−standing application when no heatsink is used,
the junction temperature can be determined by the following
expression:
TJ = (RqJA) (PD) + TA
Thermal Analysis and Design
where (RqJA)(PD) represents the junction temperature rise
caused by the dissipated power and TA is the maximum
ambient temperature.
The following procedure must be performed to determine
whether or not a heatsink will be required. First determine:
1. PD(max) maximum regulator power dissipation in the
application.
2. TA(max) maximum ambient temperature in the
application.
3. TJ(max)
maximum allowed junction temperature
(125°C for the LM2596). For a conservative
design, the maximum junction temperature
should not exceed 110°C to assure safe
operation. For every additional +10°C
temperature rise that the junction must
withstand, the estimated operating lifetime
of the component is halved.
4. RqJC
package thermal resistance junction−case.
package thermal resistance junction−ambient.
5. RqJA
(Refer to Maximum Ratings on page 2 of this data sheet or
RqJC and RqJA values).
Packages on a Heatsink
If the actual operating junction temperature is greater than
the selected safe operating junction temperature determined
in step 3, than a heatsink is required. The junction
temperature will be calculated as follows:
TJ = PD (RqJA + RqCS + RqSA) + TA
where
If the actual operating temperature is greater than the
selected safe operating junction temperature, then a larger
heatsink is required.
Some Aspects That can Influence Thermal Design
It should be noted that the package thermal resistance and
the junction temperature rise numbers are all approximate,
and there are many factors that will affect these numbers,
such as PC board size, shape, thickness, physical position,
location, board temperature, as well as whether the
surrounding air is moving or still.
Other factors are trace width, total printed circuit copper
area, copper thickness, single− or double−sided, multilayer
board, the amount of solder on the board or even color of the
traces.
The size, quantity and spacing of other components on the
board can also influence its effectiveness to dissipate the heat.
The following formula is to calculate the approximate
total power dissipated by the LM2596:
PD = (Vin x IQ) + d x ILoad x Vsat
where d is the duty cycle and for buck converter
V
t
d + on + O ,
V in
T
IQ
Vin
(quiescent current) and Vsat can be found in the
LM2596 data sheet,
is minimum input voltage applied,
12 to 40 V
Unregulated
DC Input
Cin
100 mF/50 V
RqJC is the thermal resistance junction−case,
RqCS is the thermal resistance case−heatsink,
RqSA is the thermal resistance heatsink−ambient.
R4
Feedback
+Vin
LM2596−ADJ
ON/OFF
L1
33 mH
GND
R3
D1
1N5822
Cout
220 mF
Figure 22. Inverting Buck−Boost Develops −12 V
http://onsemi.com
17
−12 V @ 0.7 A
Regulated
Output
LM2596
ADDITIONAL APPLICATIONS
Using a delayed startup arrangement, the input capacitor
can charge up to a higher voltage before the switch−mode
regulator begins to operate.
The high input current needed for startup is now partially
supplied by the input capacitor Cin.
It has been already mentioned above, that in some
situations, the delayed startup or the undervoltage lockout
features could be very useful. A delayed startup circuit
applied to a buck−boost converter is shown in Figure 27.
Figure 29 in the “Undervoltage Lockout” section describes
an undervoltage lockout feature for the same converter
topology.
Inverting Regulator
An inverting buck−boost regulator using the
LM2596−ADJ is shown in Figure 22. This circuit converts
a positive input voltage to a negative output voltage with a
common ground by bootstrapping the regulators ground to
the negative output voltage. By grounding the feedback pin,
the regulator senses the inverted output voltage and
regulates it.
In this example the LM2596−12 is used to generate a
−12 V output. The maximum input voltage in this case
cannot exceed +28 V because the maximum voltage
appearing across the regulator is the absolute sum of the
input and output voltages and this must be limited to a
maximum of 40 V.
This circuit configuration is able to deliver approximately
0.7 A to the output when the input voltage is 12 V or higher.
At lighter loads the minimum input voltage required drops
to approximately 4.7 V, because the buck−boost regulator
topology can produce an output voltage that, in its absolute
value, is either greater or less than the input voltage.
Since the switch currents in this buck−boost configuration
are higher than in the standard buck converter topology, the
available output current is lower.
This type of buck−boost inverting regulator can also
require a larger amount of startup input current, even for
light loads. This may overload an input power source with
a current limit less than 5.0 A.
Such an amount of input startup current is needed for at
least 2.0 ms or more. The actual time depends on the output
voltage and size of the output capacitor.
Because of the relatively high startup currents required by
this inverting regulator topology, the use of a delayed startup
or an undervoltage lockout circuit is recommended.
The inverting regulator operates in a different manner
than the buck converter and so a different design procedure
has to be used to select the inductor L1 or the output
capacitor Cout.
The output capacitor values must be larger than what is
normally required for buck converter designs. Low input
voltages or high output currents require a large value output
capacitor (in the range of thousands of mF).
The recommended range of inductor values for the
inverting converter design is between 68 mH and 220 mH. To
select an inductor with an appropriate current rating, the
inductor peak current has to be calculated.
The following formula is used to obtain the peak inductor
current:
I
(V ) |V |)
O ) V in x t on
[ Load in
2L 1
V
in
|V |
O
where t on +
x 1.0 , and f osc + 52 kHz.
V ) |V | f osc
in
O
I
peak
Under normal continuous inductor current operating
conditions, the worst case occurs when Vin is minimal.
R4
Feedback
12 to 40 V
Unregulated
DC Input
Cin
100 mF/50 V
Design Recommendations:
+Vin
C1
0.1 mF
LM2596−ADJ
ON/OFF
L1
33 mH
GND
R3
D1
1N5822
R2
47k
Cout
220 mF
Figure 23. Inverting Buck−Boost Develops −12 V
http://onsemi.com
18
−12 V @ 0.7 A
Regulated
Output
LM2596
+V
+Vin
+Vin
Shutdown
Input
5.0 V
0
Cin
R1
100 mF 47 k
0
LM2596−XX
1
Off
On
R2
5.6 k
5
ON/OFF 3
+Vin
GN
D
+Vin
1
LM2596−XX
Cin
100 mF
Off
On
Shutdown
Input
R3
470
Q1
2N3906
R2
47 k
5
ON/OFF 3
-Vout
R1
12 k
MOC8101
NOTE: This picture does not show the complete circuit.
GN
D
-Vout
NOTE: This picture does not show the complete circuit.
Figure 24. Inverting Buck−Boost Regulator Shutdown
Circuit Using an Optocoupler
Figure 25. Inverting Buck−Boost Regulator Shutdown
Circuit Using a PNP Transistor
With the inverting configuration, the use of the ON/OFF
pin requires some level shifting techniques. This is caused
by the fact, that the ground pin of the converter IC is no
longer at ground. Now, the ON/OFF pin threshold voltage
(1.3 V approximately) has to be related to the negative
output voltage level. There are many different possible shut
down methods, two of them are shown in Figures 24 and 25.
Negative Boost Regulator
This example is a variation of the buck−boost topology
and it is called negative boost regulator. This regulator
experiences relatively high switch current, especially at low
input voltages. The internal switch current limiting results in
lower output load current capability.
The circuit in Figure 26 shows the negative boost
configuration. The input voltage in this application ranges
from −5.0 V to −12 V and provides a regulated −12 V output.
If the input voltage is greater than −12 V, the output will rise
above −12 V accordingly, but will not damage the regulator.
R4
Cout
470 mF
Feedback
+Vin
Cin
100 mF/
50 V
−12 V
Unregulated
DC Input
LM2596−ADJ
ON/OFF
GND
D1
1N5822
R3
−12 V @ 0.7 A
Regulated
Output
L1
33 mH
Figure 26. Negative Boost Regulator
Design Recommendations:
values for the negative boost regulator is the same as for
inverting converter design.
Another important point is that these negative boost
converters cannot provide current limiting load protection in
the event of a short in the output so some other means, such
as a fuse, may be necessary to provide the load protection.
The same design rules as for the previous inverting
buck−boost converter can be applied. The output capacitor
Cout must be chosen larger than would be required for a what
standard buck converter. Low input voltages or high output
currents require a large value output capacitor (in the range
of thousands of mF). The recommended range of inductor
http://onsemi.com
19
LM2596
Delayed Startup
There are some applications, like the inverting regulator
already mentioned above, which require a higher amount of
startup current. In such cases, if the input power source is
limited, this delayed startup feature becomes very useful.
To provide a time delay between the time when the input
voltage is applied and the time when the output voltage
comes up, the circuit in Figure 27 can be used. As the input
voltage is applied, the capacitor C1 charges up, and the
voltage across the resistor R2 falls down. When the voltage
on the ON/OFF pin falls below the threshold value 1.3 V, the
regulator starts up. Resistor R1 is included to limit the
maximum voltage applied to the ON/OFF pin. It reduces the
power supply noise sensitivity, and also limits the capacitor
C1 discharge current, but its use is not mandatory.
When a high 50 Hz or 60 Hz (100 Hz or 120 Hz
respectively) ripple voltage exists, a long delay time can
cause some problems by coupling the ripple into the
ON/OFF pin, the regulator could be switched periodically
on and off with the line (or double) frequency.
+Vin
+Vin
Cin
100 mF
R1
47 k
5
ON/OFF 3
+Vin
R2
10 k
Cin
100 mF 5
R3
47 k
ON/OFF 3
GN
D
Z1
1N5242B
Q1
2N3904
R1
10 k
Vth ≈ 13 V
NOTE: This picture does not show the complete circuit.
Figure 28. Undervoltage Lockout Circuit for
Buck Converter
The following formula is used to obtain the peak inductor
current:
I
(V ) |V |)
O ) V in x t on
[ Load in
peak
V
2L 1
in
|V |
O
where t on +
x 1.0 , and f osc + 52 kHz.
V ) |V | f osc
in
O
I
GN
D
Under normal continuous inductor current operating
conditions, the worst case occurs when Vin is minimal.
R2
47 k
+Vin
+Vin
1
NOTE: This picture does not show the complete circuit.
R2
15 k
Figure 27. Delayed Startup Circuitry
Undervoltage Lockout
Cin
100 mF 5
R3
47 k
Z1
1N5242B
Some applications require the regulator to remain off until
the input voltage reaches a certain threshold level. Figure 28
shows an undervoltage lockout circuit applied to a buck
regulator. A version of this circuit for buck−boost converter
is shown in Figure 29. Resistor R3 pulls the ON/OFF pin
high and keeps the regulator off until the input voltage
reaches a predetermined threshold level with respect to the
ground Pin 3, which is determined by the following
expression:
ǒ
LM2596−XX
1
LM2596−XX
1
C1
0.1 mF
+Vin
Q1
2N3904
LM2596−XX
ON/OFF 3
GN
D
Vth ≈ 13 V
R1
15 k
Vout
NOTE: This picture does not show the complete circuit.
Figure 29. Undervoltage Lockout Circuit for
Buck−Boost Converter
Ǔ
(Q1)
V [ V ) 1.0 ) R2 V
th
Z1
R1 BE
Adjustable Output, Low−Ripple Power Supply
A 3.0 A output current capability power supply that
features an adjustable output voltage is shown in Figure 30.
This regulator delivers 3.0 A into 1.2 V to 35 V output.
The input voltage ranges from roughly 3.0 V to 40 V. In order
to achieve a 10 or more times reduction of output ripple, an
additional L−C filter is included in this circuit.
http://onsemi.com
20
LM2596
40 V Max
Unregulated
DC Input
Feedback
4
+Vin
LM2596−Adj
1
Cin
100 mF
Output
3
GN
D
5
L1
33 mH
L2
20 mH
2
ON/OFF
1.2 to 35 V @ 3.0 A
R2
50 k
Cout
220 mF
D1
1N5822
R1
1.21 k
C1
100 mF
Optional Output
Ripple Filter
Figure 30. 1.2 to 35 V Adjustable 3.0 A Power Supply with Low Output Ripple
http://onsemi.com
21
Output
Voltage
LM2596
THE LM2596 STEP−DOWN VOLTAGE REGULATOR WITH 5.0 V @ 3.0 A OUTPUT POWER CAPABILITY.
TYPICAL APPLICATION WITH THROUGH−HOLE PC BOARD LAYOUT
4
Unregulated
DC Input
+Vin
+Vin = 10 V to 40 V
1
Feedback
L1
33 mH
LM2596−ADJ
Output
3
GN
D
5
Regulated
Output Filtered
2
ON/OFF
C1
100 mF
/50 V
R2
3.0 k
D1
1N5822
ON/OFF
C2
220 mF
/16 V
−
−
−
−
−
−
100 mF, 50 V, Aluminium Electrolytic
220 mF, 25 V, Aluminium Electrolytic
3.0 A, 40 V, Schottky Rectifier, 1N5822
33 mH, DO5040H, Coilcraft
1.0 kW, 0.25 W
3.0 kW, 0.25 W
Vout2 = 5.0 V @ 3.0 A
R1
1.0 k
V
C1
C2
D1
L1
R1
R2
CFF
ǒ
Ǔ
R2
out + V ref ) 1.0 ) R1
Vref = 1.23 V
R1 is between 1.0 k and 5.0 k
Figure 31. Schematic Diagram of the 5.0 V @ 3.0 A Step−Down Converter Using the LM2596−ADJ
NOTE: Not to scale.
NOTE: Not to scale.
Figure 32. Printed Circuit Board Layout
Component Side
Figure 33. Printed Circuit Board Layout
Copper Side
References
•
•
•
•
National Semiconductor LM2596 Data Sheet and Application Note
National Semiconductor LM2595 Data Sheet and Application Note
Marty Brown “Practical Switching Power Supply Design”, Academic Press, Inc., San Diego 1990
Ray Ridley “High Frequency Magnetics Design”, Ridley Engineering, Inc. 1995
http://onsemi.com
22
LM2596
ORDERING INFORMATION
Package
Shipping†
TO−220
(Pb−Free)
50 Units / Rail
LM2596TVADJG
TO−220 (F)
(Pb−Free)
50 Units / Rail
LM2596DSADJG
D2PAK
(Pb−Free)
50 Units / Rail
LM2596DSADJR4G
D2PAK
(Pb−Free)
800 / Tape & Reel
Device
LM2596TADJG
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
MARKING DIAGRAMS
TO−220
TV SUFFIX
CASE 314B
TO−220
T SUFFIX
CASE 314D
LM
2596T−ADJ
AWLYWWG
LM
2596T−ADJ
AWLYWWG
D2PAK
DS SUFFIX
CASE 936A
LM
2596−ADJ
AWLYWWG
1
1
5
1
A
WL
Y
WW
G
5
= Assembly Location
= Wafer Lot
= Year
= Work Week
= Pb−Free Package
http://onsemi.com
23
5
LM2596
PACKAGE DIMENSIONS
TO−220
TV SUFFIX
CASE 314B−05
ISSUE L
C
B
−P−
Q
OPTIONAL
CHAMFER
E
A
U
K
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION D DOES NOT INCLUDE
INTERCONNECT BAR (DAMBAR) PROTRUSION.
DIMENSION D INCLUDING PROTRUSION SHALL
NOT EXCEED 0.043 (1.092) MAXIMUM.
L
S
W
F
5X
0.24 (0.610)
D
0.10 (0.254)
M
T P
DIM
A
B
C
D
E
F
G
H
J
K
L
N
Q
S
U
V
W
J
5X
G
V
M
H
T
N
M
−T−
SEATING
PLANE
INCHES
MIN
MAX
0.572
0.613
0.390
0.415
0.170
0.180
0.025
0.038
0.048
0.055
0.850
0.935
0.067 BSC
0.166 BSC
0.015
0.025
0.900
1.100
0.320
0.365
0.320 BSC
0.140
0.153
--0.620
0.468
0.505
--0.735
0.090
0.110
MILLIMETERS
MIN
MAX
14.529 15.570
9.906 10.541
4.318
4.572
0.635
0.965
1.219
1.397
21.590 23.749
1.702 BSC
4.216 BSC
0.381
0.635
22.860 27.940
8.128
9.271
8.128 BSC
3.556
3.886
--- 15.748
11.888 12.827
--- 18.669
2.286
2.794
TO−220
T SUFFIX
CASE 314D−04
ISSUE F
−T−
B
−Q−
B1
DETAIL A-A
A
U
C
L
J
H
G
5 PL
0.356 (0.014)
M
T Q
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION D DOES NOT INCLUDE
INTERCONNECT BAR (DAMBAR) PROTRUSION.
DIMENSION D INCLUDING PROTRUSION SHALL
NOT EXCEED 10.92 (0.043) MAXIMUM.
DIM
A
B
B1
C
D
E
G
H
J
K
L
Q
U
1234 5
K
D
E
SEATING
PLANE
M
B
B1
DETAIL A−A
http://onsemi.com
24
INCHES
MIN
MAX
0.572
0.613
0.390
0.415
0.375
0.415
0.170
0.180
0.025
0.038
0.048
0.055
0.067 BSC
0.087
0.112
0.015
0.025
0.977
1.045
0.320
0.365
0.140
0.153
0.105
0.117
MILLIMETERS
MIN
MAX
14.529 15.570
9.906 10.541
9.525 10.541
4.318
4.572
0.635
0.965
1.219
1.397
1.702 BSC
2.210
2.845
0.381
0.635
24.810 26.543
8.128
9.271
3.556
3.886
2.667
2.972
LM2596
PACKAGE DIMENSIONS
D2PAK
D2T SUFFIX
CASE 936A−02
ISSUE C
−T−
OPTIONAL
CHAMFER
A
E
U
S
K
B
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. TAB CONTOUR OPTIONAL WITHIN DIMENSIONS A
AND K.
4. DIMENSIONS U AND V ESTABLISH A MINIMUM
MOUNTING SURFACE FOR TERMINAL 6.
5. DIMENSIONS A AND B DO NOT INCLUDE MOLD
FLASH OR GATE PROTRUSIONS. MOLD FLASH
AND GATE PROTRUSIONS NOT TO EXCEED 0.025
(0.635) MAXIMUM.
TERMINAL 6
V
H
1 2 3 4 5
M
D
0.010 (0.254)
M
T
L
G
INCHES
MIN
MAX
0.386
0.403
0.356
0.368
0.170
0.180
0.026
0.036
0.045
0.055
0.067 BSC
0.539
0.579
0.050 REF
0.000
0.010
0.088
0.102
0.018
0.026
0.058
0.078
5 _ REF
0.116 REF
0.200 MIN
0.250 MIN
DIM
A
B
C
D
E
G
H
K
L
M
N
P
R
S
U
V
P
N
R
C
SOLDERING FOOTPRINT*
8.38
0.33
MILLIMETERS
MIN
MAX
9.804
10.236
9.042
9.347
4.318
4.572
0.660
0.914
1.143
1.397
1.702 BSC
13.691
14.707
1.270 REF
0.000
0.254
2.235
2.591
0.457
0.660
1.473
1.981
5 _ REF
2.946 REF
5.080 MIN
6.350 MIN
1.702
0.067
10.66
0.42
16.02
0.63
3.05
0.12
SCALE 3:1
1.016
0.04
mm Ǔ
ǒinches
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5773−3850
http://onsemi.com
25
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
LM2596/D