2 to 18GHz Instantaneous Frequency Measurement Unit DR058-F1 2 to 18GHz Instantaneous Frequency Measurement Unit The DR058-F1 utilises proprietary Teledyne Defence Limited (TDL) technology to provide state of the art performance in a package measuring only 152mm x 147mm x 30mm and weighing 1.55kg. Designed specifically for fast jet applications this product will withstand the most demanding of environments. It is characterised for –40ºC to +85ºC. For applications outside this range, please contact the TDL sales team. The DR058-F1 is a clocked sampling IFM, providing a digital 14-bit output word of the RF input frequency for each clock cycle. An external trigger will force a sample to be taken asynchronously. The internal analogue bandwidth is sufficient to capture a 50ns pulse. External connections are made via a 51 way high density D type for power and digital I/O and SMA for the RF input. With a resolution of 14 bits, the DR058-F1 gives a nominal frequency resolution of 1 MHz and an rms accuracy of ≤4.5MHz with an input SNR of 3dB or better. FEATURES • • • • • • • 14 Bit resolution External trigger or clocked sampling 50ns pulse capable 16GHz Instantaneous bandwidth -50dBm sensitivity Small form factor Low weight Low power consumption This product is recommended for new designs. Other IFM configurations are available and for further information, please contact the TDL Sales Team. APPLICATIONS • Electronic Support Measures (ESM) • Radar Warning Receivers (RWR) • ECM Set-on • Airborne, Fixed Wing & Rotary • Land • Naval See restrictions on published datasheets at www.teledynedefence.co.uk/ Teledyne Defence, Airedale House Royal London Industrial Estate Acorn Park, Charlestown Shipley, West Yorkshire | UK, BD17 7SW Tel: +44 (0) 1274 531` 602 | Fax: +44 (0) 1274 595 724 Email: [email protected] | Web: www.teledynedefence.co.uk DR058-F1 | 022016 | Page 1 of 7 2 to 18GHz Instantaneous Frequency Measurement Unit DR058-F1 ELECTRICAL SPECIFICATIONS Ref Parameter Units Value Min 1 Operating Frequency Range 2 3 Nom Notes Max GHz 1.955 Unambiguous Bandwidth GHz 1.5 Frequency Resolution MHz 1 4 Digital Frequency Resolution Bits 14 5 Clock Rate MHz 15 50 6 Throughput Time ns 88 118 7 RF Input Dynamic Range dBm -50 10 8 RF Input Signal/Noise Ratio dB 3 50 9 RF Input Pulse Width ns 10 Recovery Time ns 11 RF Input VSWR 12 Frequency Error (RMS) at 3 dB SNR MHz Frequency Peak Error at 3 dB SNR MHz 14 Peak Error Rate at 3 dB SNR 15 16 18 18.5 1 3 CW 4 50 5 4.5 6 % 0.04 7 Bad Data Error Rate at 3 dB SNR % 1 8 Simultaneous Signal: Level Simultaneous Signal: Frequency Separation Overload Power dBc 15 6 10 MHz 9 100 dBm 9 20 19 Temperature Range (operating) 20 Power Consumption 21 Power Supply Current: +12v Rail mA 900 22 Power Supply Current: +5v Rail mA 2500 23 Power Supply Current: -5v Rail mA 350 24 Weight (Approx.) kg 1.55 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 2 2.2:1 13 17 18.045 °C Watts -40 10 85 25 Nominal frequency resolution is unambiguous bandwidth divided by number of bits. See timing diagrams. Based on a 50 MHz clock. Minimum SNR required for nominal operation. Minimum pulse width is defined by internal video bandwidth. Given as the maximum time required between the removal of a pulse of RF at any power within the operating dynamic range and the arrival of the next pulse to ensure the correct measurement of the second pulse. The actual resolution, i.e.,the change of frequency required to change 1 bit of the output word varies with frequency. The rms accuracy is calculated as the standard deviation of the frequency distribution. The rms accuracy is specified for 3dB and 0dB input SNR. The rms error excludes those measurements that are flagged as “bad data”. The percentage number of measurements that exceed the peak error frequency. The percentage number of measurements that cause the ‘bad data’ signal to be asserted. Simultaneous signals are defined as signals which overlap by at least 30ns during a measurement cycle. A valid measurement will be made on the larger of two signals provided that a) the amplitude difference between them is 10dB and b) there is at least 100MHz frequency separation. Maximum input power without damage. See restrictions on published datasheets at www.teledynedefence.co.uk/ Teledyne Defence, Airedale House Royal London Industrial Estate Acorn Park, Charlestown Shipley, West Yorkshire | UK, BD17 7SW Tel: +44 (0) 1274 531` 602 | Fax: +44 (0) 1274 595 724 Email: [email protected] | Web: www.teledynedefence.co.uk DR058-F1 | 022016 | Page 2 of 7 2 to 18GHz Instantaneous Frequency Measurement Unit DR058-F1 TIMING INFORMATION Continuously Clocked Mode Parameter Tclk Trfpw Topdly Tvs Tmeas Description ClockPeriod RF Pulse Width Data Output Delay Video Settling time Throughput Time from settled video digitisation Min Timings Nominal 20 ns Tclk+30 ns 0 ns 15 ns Max 67 ns CW 10 ns 25 ns Tclk(3.5±0.5)+Topdly Note that the recovery time between two consecutive pulses can be as low asTclk. No Data Valid output is provided in continuous clock mode. See restrictions on published datasheets at www.teledynedefence.co.uk/ Teledyne Defence, Airedale House Royal London Industrial Estate Acorn Park, Charlestown Shipley, West Yorkshire | UK, BD17 7SW Tel: +44 (0) 1274 531` 602 | Fax: +44 (0) 1274 595 724 Email: [email protected] | Web: www.teledynedefence.co.uk DR058-F1 | 022016 | Page 3 of 7 2 to 18GHz Instantaneous Frequency Measurement Unit DR058-F1 TIMING INFORMATION Triggered Mode Timings Nominal Parameter Description Tclk Clock Period Min 20 ns Trfpw RF Pulse Width 50 ns Textrpw External Trigger Width 35 ns CW Topdly Data Output Delay 0 ns Trec (Note 1) Recovery Time 10 ns 50 ns Ttrd (Note 2) Trigger Delay from RF Tmeas Throughput Time Max 67 ns CW 4 ns 12 ns Trd+Tclk (4.5±0.5)+Topdly Note 1 If a second pulse starts within this period the frequency measured may not be correct. Note 2 This timing will ensure that the frequency within a 50 ns pulse is measured correctly.. When no external trigger is supplied, but RF is present, the device will run in continuous clock mode. The rising edge of ExtTrigger causes the digitized tier video data at the front of the pipeline to be held (frozen) after a delay of approximately 25 ns (to allow video to settle) for a minimum period of 1 clock cycle to guarantee that this data enters the pipeline at the next rising clock edge. See restrictions on published datasheets at www.teledynedefence.co.uk/ Teledyne Defence, Airedale House Royal London Industrial Estate Acorn Park, Charlestown Shipley, West Yorkshire | UK, BD17 7SW Tel: +44 (0) 1274 531` 602 | Fax: +44 (0) 1274 595 724 Email: [email protected] | Web: www.teledynedefence.co.uk DR058-F1 | 022016 | Page 4 of 7 2 to 18GHz Instantaneous Frequency Measurement Unit DR058-F1 PIN DESIGNATIONS Pin Signal 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 IFM Clock + 0V 0V Ext Trigger Freq 1 Ext Trigger + Freq 3 Bad Data Freq 7 Freq 9 Data Valid Freq 11 Data Valid + Freq 12 0V 0V -5V 0V IFM Clock + 0V 0V Freq 0 Freq 1 + Freq 2 Freq 3 + Freq 4 Bad Data + Freq 8 Freq 11 + Freq 10 Freq 12 + 0V Freq 13 0V Freq 13 + +12V 0V Freq 0 + Freq 2 + Freq 4 + Freq 5 + Freq 5 Freq 7 + Freq 6 + Freq 6 Freq 9 + Freq 8 + Freq 10 + OV +5V +5V Direction Input Return Return Input Output Input Output Output Output Output Output Output Output Output Return Return Power Return Input Return Return Output Output Output Output Output Output Output Output Output Output Return Output Return Output Power Return Output Output Output Output Output Output Output Output Output Output Output Return Power Power See restrictions on published datasheets at www.teledynedefence.co.uk/ Teledyne Defence, Airedale House Royal London Industrial Estate Acorn Park, Charlestown Shipley, West Yorkshire | UK, BD17 7SW Tel: +44 (0) 1274 531` 602 | Fax: +44 (0) 1274 595 724 Email: [email protected] | Web: www.teledynedefence.co.uk DR058-F1 | 022016 | Page 5 of 7 2 to 18GHz Instantaneous Frequency Measurement Unit DR058-F1 ENVIRONMENTAL SCREENING 100% of units subjected to: burn in 8 hours operational at 71ºC, random vibration (as below), 5min per axis, thermal shock (as below), random vibration (as below), 5min per axis. Environmental Data Compliance can be shown by similarity to the following environmental conditions: Sinusoidal Vibration: MIL-STD-202F, Method 204 - 5g profile between 5 and 104Hz for 90 min per axis Random Vibration: MIL-STD-810D, Method 514.3 – specified profile (below) with max of 0.2g²/Hz for 60 min per axis, 20 to 2000Hz Mechanical Shock: MIL-STD-202F, Method 213B – 15g/11ms, 3 shocks in each axis in each direction (18 total) Acceleration: MIL-STD-202F, Method 212A, condition B, 6 to 14g High Temperature storage: MIL-STD-810D, Method 501.2 - 95ºC for 8 hours High Temperature operational: MIL-STD-820D, Method 501.2 – 71ºC / 30min, 60ºC / 60min, 55ºC / 4hr Thermal Shock: 10 Cycles of –40ºC to 71ºC, 5 min ramp, 2hr dwell Low Temperature storage: MIL-STD-810D, Method 502.2 - -54ºC for 8 hours. Low temperature operational: MIL-STD-810D, Method 502.2 - -40ºC / 60min. DR058- Combined temperature, altitude & humidity: MIL-STD-810D. Method 520 – temperature –40ºC F1 to 70ºC, storage condition sea level to 17000m (87.6mb), operating condition sea level to 11000m (228mb), relative humidity at sea level 75%, 10 Cycles. Humidity: MIL-STD-810D, Method 507.2, procedure 2 – RH 85% to 95%, temperature 30ºC to 60ºC, 24 hour cycle, 10 cycles. EMI/EMC: Generally in accordance with MIL-STD-461E. Please note that system precautions must be taken to prevent interfering signals entering the high gain RF front end. See restrictions on published datasheets at www.teledynedefence.co.uk/ Teledyne Defence, Airedale House Royal London Industrial Estate Acorn Park, Charlestown Shipley, West Yorkshire | UK, BD17 7SW Tel: +44 (0) 1274 531` 602 | Fax: +44 (0) 1274 595 724 Email: [email protected] | Web: www.teledynedefence.co.uk DR058-F1 | 022016 | Page 6 of 7 2 to 18GHz Instantaneous Frequency Measurement Unit DR058-F1 OUTLINE DRAWING See restrictions on published datasheets at www.teledynedefence.co.uk/ Teledyne Defence, Airedale House Royal London Industrial Estate Acorn Park, Charlestown Shipley, West Yorkshire | UK, BD17 7SW Tel: +44 (0) 1274 531` 602 | Fax: +44 (0) 1274 595 724 Email: [email protected] | Web: www.teledynedefence.co.uk DR058-F1 | 022016 | Page 7 of 7