5225

SENSITRON
SEMICONDUCTOR
S441IE
TECHNICAL DATA
DATA SHEET 5225, Rev. -
COMMON CATHODE ASSEMBLY
DESCRIPTION: A 1000 VOLT, 40 AMP, 200 NANOSECOND DOUBLER ASSEMBLY
MAX. RATINGS / ELECTRICAL CHARACTERISTICS
RATING
Peak Inverse Voltage
o
All ratings are at TA = 25 C unless otherwise specified.
CONDITIONS
MIN
TYP
MAX
UNIT
-
-
-
1000
Vdc
-
-
40
Amps
(PIV)
Average DC Output
Current (TC = Case Temp)
(Io)
Peak Single Cycle Surge
Current
(IFSM)
o
TC = 55 C
o
TC = 100 C
tp = 8.3 ms Single
Half Cycle Sine
Wave,
Superimposed On
Rated Load
o
24
-
-
300
Amps(pk)
Peak Recurring Surge
Current
(IFRM)
TA = 25 C
-
-
Operating and Storage
Temp.
(Top & Tstg)
-
-55
-
+150
C
If = 8.0Adc
(300 sec pulse,
duty cycle < 2%)
-
-
2.2
Volts
-
-
10
Amps
Maximum Forward
Voltage Per Leg
(Vf)
Maximum Instantaneous
Reverse Current At Rated
(PIV)
TA = 25 C
Reverse Recovery Time
If = 0.5A, Ir = 1.0A, Irr
= 0.25A
(trr)
Amps
200
TA = 100 C
-
-
200
nsec
-
-
2.0
C/W
Measured on
discrete rectifiers
prior to assembly.
Max. Thermal Resistance
(R
-
JC)
©2012 Sensitron Semiconductor 221 West Industry Court  Deer Park, NY 11729-4681
 (631) 586-7600 FAX (631) 242-9798 www.sensitron.com [email protected]
S441IE
SENSITRON
TECHNICAL DATA
DATA SHEET 5225, Rev. -
MECHANICAL DIMENSIONS: In Inches / mm
Note: Case finish - Black Anodized
DISCLAIMER:
1- The information given herein, including the specifications and dimensions, is subject to change without prior notice to improve product
characteristics. Before ordering, purchasers are advised to contact the Sensitron Semiconductor sales department for the latest version of the
datasheet(s).
2- In cases where extremely high reliability is required (such as use in nuclear power control, aerospace and aviation, traffic equipment, medical
equipment , and safety equipment) , safety should be ensured by using semiconductor devices that feature assured safety or by means of
users’ fail-safe precautions or other arrangement .
3- In no event shall Sensitron Semiconductor be liable for any damages that may result from an accident or any other cause during operation of
the user’s units according to the datasheet(s). Sensitron Semiconductor assumes no responsibility for any intellectual property claims or any
other problems that may result from applications of information, products or circuits described in the datasheets.
4- In no event shall Sensitron Semiconductor be liable for any failure in a semiconductor device or any secondary damage resulting from use at
a value exceeding the absolute maximum rating.
5- No license is granted by the datasheet(s) under any patents or other rights of any third party or Sensitron Semiconductor.
6- The datasheet(s) may not be reproduced or duplicated, in any form, in whole or part, without the expressed written permission of Sensitron
Semiconductor.
7- The products (technologies) described in the datasheet(s) are not to be provided to any party whose purpose in their application will hinder
maintenance of international peace and safety nor are they to be applied to that purpose by their direct purchasers or any third party. When
exporting these products (technologies), the necessary procedures are to be taken in accordance with related laws and regulations.
©2012 Sensitron Semiconductor 221 West Industry Court  Deer Park, NY 11729-4681
 (631) 586-7600 FAX (631) 242-9798 www.sensitron.com [email protected]
Similar pages