BootLog-am335xevm.pdf

CCCCCCCC
U-Boot SPL 2013.01.01-00123-g2830d15 (Jun 26 2013 - 17:23:54)
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Peripheral mode controller at 47401000 using PIO, IRQ 0
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Host mode controller at 47401800 using PIO, IRQ 0
OMAP SD/MMC: 0
reading u-boot.img
reading u-boot.img
U-Boot 2013.01.01-00123-g2830d15 (Jun 26 2013 - 17:23:54)
I2C:
ready
DRAM: 1 GiB
WARNING: Caches not enabled
NAND: 256 MiB
MMC:
OMAP SD/MMC: 0, OMAP SD/MMC: 1
*** Warning - bad CRC, using default environment
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Peripheral mode controller at 47401000 using PIO, IRQ 0
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Host mode controller at 47401800 using PIO, IRQ 0
Net:
<ethaddr> not set. Validating first E-fuse MAC
cpsw
00 00
Hit any key to stop autoboot: 1 00
0
08 08 08
mmc0 is current device
SD/MMC found on device 0
reading uEnv.txt
214 bytes read in 4 ms (51.8 KiB/s)
Loaded environment from uEnv.txt
Importing environment from mmc ...
Running uenvcmd ...
reading uImage
4178824 bytes read in 420 ms (9.5 MiB/s)
## Booting kernel from Legacy Image at 81000000 ...
Image Name:
Linux-3.2.0-00244-gcf99001
Image Type:
ARM Linux Kernel Image (uncompressed)
Data Size:
4178760 Bytes = 4 MiB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[
0.000000] Linux version 3.2.0-00244-gcf99001 ([email protected]) (gcc version 4.6.x-google 20120106
(prerelease) (GCC) ) #5 Fri Jun 21 18:20:51 IST 2013
[
0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7d
[
0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[
0.000000] Machine: am335xevm
[
0.000000] Memory policy: ECC disabled, Data cache writeback
[
0.000000] AM335X ES2.1 (sgx neon )
[
0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048
[
0.000000] Kernel command line: console=ttyO0,115200n8 androidboot.console=ttyO0 mem=512M root=/dev/mmcblk0p2
rw rootfstype=ext4 rootwait init=/init ip=off
[
0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[
0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[
0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[
0.000000] Memory: 512MB = 512MB total
[
0.000000] Memory: 509880k/509880k available, 14408k reserved, 0K highmem
[
0.000000] Virtual kernel memory layout:
[
0.000000]
vector : 0xffff0000 - 0xffff1000
(
4 kB)
[
0.000000]
fixmap : 0xfff00000 - 0xfffe0000
( 896 kB)
[
0.000000]
vmalloc : 0xe0800000 - 0xff000000
( 488 MB)
[
0.000000]
lowmem : 0xc0000000 - 0xe0000000
( 512 MB)
[
0.000000]
modules : 0xbf000000 - 0xc0000000
( 16 MB)
[
0.000000]
.text : 0xc0008000 - 0xc078a000
(7688 kB)
[
0.000000]
.init : 0xc078a000 - 0xc07e0000
( 344 kB)
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
0.000000]
0.000000]
0.000000]
0.000000]
0.000000]
0.000000]
0.000000]
0.000000]
0.000000]
0.000091]
0.089233]
0.089355]
0.089416]
0.089752]
0.089813]
0.146240]
0.146972]
0.147155]
0.148071]
0.148925]
0.149871]
0.150299]
0.150390]
0.150512]
0.150512]
0.150512]
0.158264]
0.159088]
0.159851]
0.159942]
0.160064]
0.160308]
0.160339]
0.160339]
0.160369]
0.160491]
0.179260]
0.180358]
0.182464]
0.183776]
0.185913]
0.188049]
0.188903]
0.190185]
0.191467]
0.192749]
0.194000]
0.195281]
0.196594]
0.197845]
0.199127]
0.199401]
0.199829]
0.200347]
0.200408]
0.200408]
0.200408]
0.200408]
0.200469]
0.200622]
0.215209]
0.215393]
0.215545]
0.215576]
0.216278]
0.216491]
0.216644]
0.216644]
0.217010]
0.217102]
0.217224]
0.217224]
0.217254]
0.217254]
0.217254]
0.217651]
0.217681]
0.218017]
0.218322]
0.218505]
0.218841]
0.219085]
0.219207]
0.219207]
.data : 0xc07e0000 - 0xc084ba70
( 431 kB)
.bss : 0xc084ba94 - 0xc09a3890
(1376 kB)
NR_IRQS:396
IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts
Total of 128 interrupts on 1 active controller
OMAP clockevent source: GPTIMER2 at 24000000 Hz
OMAP clocksource: GPTIMER1 at 32768 Hz
sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms
Console: colour dummy device 80x30
Calibrating delay loop... 996.14 BogoMIPS (lpj=4980736)
pid_max: default: 32768 minimum: 301
Security Framework initialized
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
ftrace: allocating 22068 entries in 65 pages
omap_hwmod: pruss: failed to hardreset
print_constraints: dummy:
NET: Registered protocol family 16
OMAP GPIO hardware version 0.1
omap_mux_init: Add partition: #1: core, flags: 0
omap_i2c.1: alias fck already exists
omap2_mcspi.1: alias fck already exists
omap2_mcspi.2: alias fck already exists
edma.0: alias fck already exists
edma.0: alias fck already exists
edma.0: alias fck already exists
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
registerd cppi-dma Intr @ IRQ 17
Cppi41 Init Done Qmgr-base(e087a000) dma-base(e0878000)
Cppi41 Init Done
musb-ti81xx musb-ti81xx: musb0, board_mode=0x13, plat_mode=0x3
musb-ti81xx musb-ti81xx: musb1, board_mode=0x13, plat_mode=0x1
omap_i2c omap_i2c.1: bus 1 rev2.4.0 at 100 kHz
tps65910 1-002d: JTAGREVNUM 0x0
print_constraints: VRTC:
print_constraints: VIO: at 1500 mV
print_constraints: VDD1: 600 <--> 1500 mV at 1325 mV normal
print_constraints: VDD2: 600 <--> 1500 mV at 1137 mV normal
print_constraints: VDD3: 5000 mV
print_constraints: VDIG1: at 1800 mV
print_constraints: VDIG2: at 1800 mV
print_constraints: VPLL: at 1800 mV
print_constraints: VDAC: at 1800 mV
print_constraints: VAUX1: at 1800 mV
print_constraints: VAUX2: at 3300 mV
print_constraints: VAUX33: at 3300 mV
print_constraints: VMMC: at 3300 mV
tps65910 1-002d: No interrupt support, no core IRQ
Advanced Linux Sound Architecture Driver Version 1.0.24.
Bluetooth: Core ver 2.16
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO socket layer initialized
Switching to clocksource gp timer
musb-hdrc: version 6.0, ?dma?, otg (peripheral+host)
musb-hdrc musb-hdrc.0: dma type: dma-cppi41
MUSB0 controller's USBSS revision = 4ea20800
musb0: Enabled SW babble control
musb-hdrc musb-hdrc.0: USB OTG mode controller at e083c000 using DMA, IRQ 18
musb-hdrc musb-hdrc.1: dma type: dma-cppi41
MUSB1 controller's USBSS revision = 4ea20800
musb1: Enabled SW babble control
musb-hdrc musb-hdrc.1: MUSB HDRC host driver
musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 1
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: MUSB HDRC host driver
usb usb1: Manufacturer: Linux 3.2.0-00244-gcf99001 musb-hcd
usb usb1: SerialNumber: musb-hdrc.1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
musb-hdrc musb-hdrc.1: USB Host mode controller at e083e800 using DMA, IRQ 19
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
0.219207]
0.219238]
0.219421]
0.219665]
0.219665]
0.219665]
0.219696]
0.219909]
0.314819]
0.315063]
0.315124]
0.315826]
0.316040]
0.316864]
0.316894]
0.316955]
0.319335]
1.008117]
1.012115]
1.019744]
1.027374]
1.034973]
1.042602]
1.050292]
1.059661]
1.065216]
1.068664]
1.075164]
1.081604]
1.095520]
1.100524]
1.104400]
1.119567]
1.122955]
1.126220]
1.129302]
1.135650]
1.140930]
1.159820]
1.164886]
1.168853]
1.191284]
1.197326]
1.203277]
1.210296]
1.217071]
1.222625]
1.228179]
1.233825]
1.239013]
1.244293]
1.250183]
1.254333]
1.258666]
1.263305]
1.267333]
1.274963]
1.303497]
1.401458]
1.411193]
1.415557]
1.422729]
1.427307]
1.430694]
1.434387]
1.443176]
1.448730]
1.454498]
1.460845]
1.467193]
1.473571]
1.480194]
1.486480]
1.494384]
1.602844]
1.607360]
1.611419]
1.661254]
1.667724]
1.675231]
1.678802]
1.686248]
1.690856]
1.695800]
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
NetWinder Floating Point Emulator V0.97 (double precision)
ashmem: initialized
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
fuse init (API version 7.17)
msgmni has been set to 995
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
omap_uart.0: ttyO0 at MMIO 0x44e09000 (irq = 72) is a OMAP UART0
console [ttyO0] enabled
omap_uart.1: ttyO1 at MMIO 0x48022000 (irq = 73) is a OMAP UART1
omap_uart.2: ttyO2 at MMIO 0x48024000 (irq = 74) is a OMAP UART2
omap_uart.3: ttyO3 at MMIO 0x481a6000 (irq = 44) is a OMAP UART3
omap_uart.4: ttyO4 at MMIO 0x481a8000 (irq = 45) is a OMAP UART4
omap_uart.5: ttyO5 at MMIO 0x481aa000 (irq = 46) is a OMAP UART5
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
i2c-core: driver [tsl2550] using legacy suspend method
i2c-core: driver [tsl2550] using legacy resume method
at24 1-0051: 32768 byte 24c256 EEPROM, writable, 64 bytes/write
Detected a daughter card on AM335x EVM..
CPLD version: CPLD1.0G 00
01
at24 1-0050: 32768 byte 24c256 EEPROM, writable, 64 bytes/write
Board name: A33515BB
Board version: 1.5B
SKU: SKU#01
The board is general purpose EVM in profile 0
da8xx_lcdc.0: alias fck already exists
da8xx_lcdc da8xx_lcdc.0: GLCD: Found TFC_S9700RTWV35TR_01B panel
omap-gpmc omap-gpmc: GPMC revision 6.0
Registering NAND on CS0
omap_i2c.2: alias fck already exists
omap_i2c omap_i2c.2: bus 2 rev2.4.0 at 100 kHz
tsl2550 2-0039: standard operating mode
tsl2550 2-0039: registering lightsensor-level input device
input: lightsensor-level as /devices/virtual/input/input0
tsl2550 2-0039: support ver. 1.2 enabled
davinci-mcasp.1: alias fck already exists
davinci-mcasp.0: alias fck already exists
omap_hsmmc.0: alias fck already exists
omap_hsmmc.2: alias fck already exists
am335xevm: bt init
(stk) :sysfs entries created
(stk) : debugfs entries created
(hci_tty): inside hci_tty_init
(hci_tty): allocated 251, 0
_regulator_get: 2-0018 supply Vdd not found, using dummy regulator
_regulator_get: 2-0018 supply Vdd_IO not found, using dummy regulator
lis3lv02d: 8 bits 3DLH sensor found
input: ST LIS3LV02DL Accelerometer as /devices/platform/lis3lv02d/input/input1
NFC Driver for TI WiLink
mtdoops: mtd device (mtddev=name/number) must be supplied
omap2-nand driver initializing
ONFI flash detected
ONFI param page 0 valid
NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron MT29F2G08ABAEAWP)
Creating 8 MTD partitions on "omap2-nand.0":
0x000000000000-0x000000020000 : "SPL"
0x000000020000-0x000000040000 : "SPL.backup1"
0x000000040000-0x000000060000 : "SPL.backup2"
0x000000060000-0x000000080000 : "SPL.backup3"
0x000000080000-0x000000260000 : "U-Boot"
0x000000260000-0x000000280000 : "U-Boot Env"
0x000000280000-0x000000780000 : "Kernel"
0x000000780000-0x000010000000 : "File System"
OneNAND driver initializing
CAN device driver interface
CAN bus driver for Bosch D_CAN controller 1.0
davinci_mdio davinci_mdio.0: davinci mdio revision 1.6
davinci_mdio davinci_mdio.0: detected phy mask fffffffe
davinci_mdio.0: probed
davinci_mdio davinci_mdio.0: phy[0]: device 0:00, driver unknown
PPP generic driver version 2.4.2
PPP BSD Compression module registered
PPP Deflate Compression module registered
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
1.701202]
1.707336]
1.713317]
1.719177]
1.725402]
1.728820]
1.734832]
1.740722]
1.749114]
1.754333]
1.760620]
1.765594]
1.771759]
1.777099]
1.783935]
1.788513]
1.794952]
1.800781]
1.807373]
1.813598]
1.817443]
1.822753]
1.826690]
1.832305]
1.840148]
1.847259]
1.854797]
1.859985]
1.866912]
1.872070]
1.876007]
1.880645]
1.887207]
1.895721]
1.904144]
1.909210]
1.916534]
1.920410]
1.925537]
1.931549]
1.936614]
1.942993]
2.181945]
2.188446]
2.193450]
2.202301]
2.206939]
2.211944]
2.216888]
2.225646]
2.230041]
2.237670]
2.243560]
2.352752]
2.357574]
2.362579]
2.367492]
2.372863]
2.377685]
2.385253]
2.393096]
2.400787]
2.408447]
2.418945]
2.425994]
2.432434]
2.435546]
2.438568]
2.443847]
2.448486]
2.453552]
2.460144]
2.465789]
2.473083]
2.479461]
2.484283]
2.490020]
2.494934]
2.498443]
2.503753]
2.506347]
2.512176]
2.517120]
2.521820]
usbcore: registered new interface driver cdc_ether
usbcore: registered new interface driver cdc_eem
usbcore: registered new interface driver dm9601
usbcore: registered new interface driver cdc_subset
cdc_ncm: 04-Aug-2011
usbcore: registered new interface driver cdc_ncm
usbcore: registered new interface driver cdc_acm
cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial Driver core
USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver option
option: v0.7.2:USB Driver for GSM modems
gadget: Mass Storage Function, version: 2009/09/11
gadget: Number of LUNs=1
lun0: LUN: removable file: (no medium)
gadget: android_usb ready
musb-hdrc musb-hdrc.0: MUSB HDRC host driver
musb-hdrc musb-hdrc.0: new USB bus registered, assigned bus number 2
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: MUSB HDRC host driver
usb usb2: Manufacturer: Linux 3.2.0-00244-gcf99001 musb-hcd
usb usb2: SerialNumber: musb-hdrc.0
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
mousedev: PS/2 mouse device common for all mice
input: matrix-keypad as /devices/platform/matrix-keypad/input/input2
input: ti-tsc as /devices/platform/omap/ti_tscadc/tsc/input/input3
using rtc device, am33xx-rtc, for alarms
omap_rtc am33xx-rtc: rtc core: registered am33xx-rtc as rtc0
i2c /dev entries driver
Linux video capture interface: v2.00
usbcore: registered new interface driver uvcvideo
USB Video Class driver (1.1.1)
input: lm75-temp as /devices/virtual/input/input4
lm75 2-0048: hwmon0: sensor 'tmp275'
OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: [email protected]
Bluetooth: HCI UART driver ver 2.2
Bluetooth: HCI H4 protocol initialized
Bluetooth: HCILL protocol initialized
Bluetooth: Bluetooth Driver for TI WiLink - Version 1.0
cpuidle: using governor ladder
cpuidle: using governor menu
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
logger: created 256K log 'log_main'
logger: created 256K log 'log_events'
logger: created 256K log 'log_radio'
logger: created 256K log 'log_system'
tiadc tiadc: attached adc driver
usbcore: registered new interface driver snd-usb-audio
_regulator_get: 2-001b supply IOVDD not found, using dummy regulator
_regulator_get: 2-001b supply DVDD not found, using dummy regulator
_regulator_get: 2-001b supply AVDD not found, using dummy regulator
_regulator_get: 2-001b supply DRVDD not found, using dummy regulator
asoc: tlv320aic3x-hifi <-> davinci-mcasp.1 mapping ok
asoc: wl1271bt <-> davinci-mcasp.0 mapping ok
ALSA device list:
#0: AM335X EVM
oprofile: hardware counters not available
oprofile: using timer interrupt.
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (7966 buckets, 31864 max)
ctnetlink v0.93: registering with nfnetlink.
NF_TPROXY: Transparent proxy support initialized, version 4.1.0
NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
xt_time: kernel timezone is -0000
ip_tables: (C) 2000-2006 Netfilter Core Team
arp_tables: (C) 2002 David S. Miller
TCP cubic registered
NET: Registered protocol family 10
Mobile IPv6
ip6_tables: (C) 2000-2006 Netfilter Core Team
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
NET: Registered protocol family 15
[
2.526458]
[
2.533050]
[
2.537689]
[
2.542175]
[
2.548278]
[
2.553466]
[
2.558837]
[
2.562744]
[
2.568298]
[
2.573791]
[
2.580108]
[
2.585113]
[
2.593139]
[
2.597656]
[
2.603210]
[
2.608062]
[
2.614776]
[
2.619140]
[
2.627777]
[
2.634796]
[
2.641204]
[
2.648559]
[
2.657958]
[
2.704284]
[
2.710449]
[
2.716918]
[
2.825897]
[
2.844848]
[
2.851379]
[
3.027954]
[
3.036499]
[
3.043182]
[
3.076690]
[
3.170684]
[
3.231292]
[
3.281097]
[
3.341400]
[
3.347656]
[
3.353424]
[
3.358825]
[
3.418029]
[
3.610107]
[
3.617218]
[
3.636108]
[
3.640533]
[
3.649536]
[
3.654052]
[
3.657012]
[email protected]:/
[
3.987731]
[
61.839111]
[
62.617095]
[
62.623382]
[
62.635406]
[
63.110351]
[
63.112762]
[
64.613159]
[
64.618072]
[ 116.696075]
[ 116.699035]
[ 116.703613]
[ 116.748779]
[ 116.820098]
[ 118.243438]
[ 136.024749]
[ 151.801544]
can: controller area network core (rev 20090105 abi 8)
NET: Registered protocol family 29
can: raw protocol (rev 20090105)
can: broadcast manager protocol (rev 20090105 t)
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM ver 1.11
Bluetooth: BNEP (Ethernet Emulation) ver 1.3
Bluetooth: BNEP filters: protocol multicast
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
Registering the dns_resolver key type
VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3
ThumbEE CPU extension supported.
mux: Failed to setup hwmod io irq -22
Power Management for AM33XX family
Trying to load am335x-pm-firmware.bin (60 secs timeout)
Copied the M3 firmware to UMEM
Cortex M3 Firmware Version = 0x181
clock: disabling unused clocks to save power
Detected MACID=c8:a0:30:a1:db:1f
input: gpio-keys as /devices/platform/gpio-keys/input/input5
omap_rtc am33xx-rtc: setting system clock to 2000-01-01 00:00:01 UTC (946684801)
Waiting for root device /dev/mmcblk0p2...
mmc0: new high speed SDHC card at address b368
mmcblk0: mmc0:b368 SD
7.51 GiB
mmcblk0: p1 p2 p3 p4
mmc1: card claims to support voltages below the defined range. These will be ignored.
mmc1: queuing unknown CIS tuple 0x91 (3 bytes)
mmc1: new SDIO card at address 0001
EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 179:2.
Freeing init memory: 344K
init (1): /proc/1/oom_adj is deprecated, please use /proc/1/oom_score_adj instead.
init: cannot open '/initlogo.rle'
EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: nomblk_io_submit,errors=panic
init: cannot find '/system/etc/install-recovery.sh', disabling 'flash_recovery'
Disabling lock debugging due to kernel taint
Compat-wireless backport release: ol_R5.SP3.03
Backport based on wl12xx.git ol_R5.SP3.03
(stk) :line disc installation timed out
cfg80211: Calling CRDA to update world regulatory domain
wl12xx: driver version: rowboat-jb-am335x-4.1.2-244-gcf99001
wl12xx: compilation time: Fri Jun 21 18:20:59 2013
android_usb: already disabled
android_usb: already disabled
android_usb: already disabled
mtp_bind_config
adb_bind_config
# [
3.811614] adb_open
warning: `rild' uses 32-bit capabilities (legacy support in use)
request_suspend_state: wakeup (3->0) at 61816991810 (2000-01-01 00:01:00.683107178 UTC)
net eth0: CPSW phy found : id is : 0x4dd074
PHY 0:01 not found
ADDRCONF(NETDEV_UP): eth0: link is not ready
acc_open
acc_release
PHY: 0:00 - Link is Up - 100/Full
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
mtp_bind_config
adb_bind_config
adb_release
init: untracked pid 93 exited
init: sys_prop: permission denied uid:1003 name:service.bootanim.exit
adb_open
(hci_tty): inside hci_tty_open (de03f648, cef6f9c0)
(hci_tty): inside hci_tty_release (de03f648, cef6f9c0)
[email protected]:/ #
Similar pages