U-Boot SPL 2013.01.01-00123-g2830d15 (Jun 26 2013 - 17:23:54) musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Peripheral mode controller at 47401000 using PIO, IRQ 0 musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Host mode controller at 47401800 using PIO, IRQ 0 OMAP SD/MMC: 0 reading u-boot.img reading u-boot.img U-Boot 2013.01.01-00123-g2830d15 (Jun 26 2013 - 17:23:54) I2C: ready DRAM: 256 MiB WARNING: Caches not enabled NAND: No NAND device found!!! 0 MiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 *** Warning - readenv() failed, using default environment musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Peripheral mode controller at 47401000 using PIO, IRQ 0 musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Host mode controller at 47401800 using PIO, IRQ 0 Net: <ethaddr> not set. Validating first E-fuse MAC cpsw 00 00 Hit any key to stop autoboot: 1 00 0 08 08 08 mmc0 is current device SD/MMC found on device 0 reading uEnv.txt 214 bytes read in 3 ms (69.3 KiB/s) Loaded environment from uEnv.txt Importing environment from mmc ... Running uenvcmd ... reading uImage 4178824 bytes read in 462 ms (8.6 MiB/s) ## Booting kernel from Legacy Image at 81000000 ... Image Name: Linux-3.2.0-00244-gcf99001 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4178760 Bytes = 4 MiB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Linux version 3.2.0-00244-gcf99001 (a0393957@psplinux052) (gcc version 4.6.x-google 20120106 (prerelease) (GCC) ) #5 Fri Jun 21 18:20:51 IST 2013 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: am335xevm [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] AM335X ES1.0 (sgx neon ) [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 [ 0.000000] Kernel command line: console=ttyO0,115200n8 androidboot.console=ttyO0 mem=256M root=/dev/mmcblk0p2 rw rootfstype=ext4 rootwait init=/init ip=off [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Memory: 256MB = 256MB total [ 0.000000] Memory: 249984k/249984k available, 12160k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xd0800000 - 0xff000000 ( 744 MB) [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc078a000 (7688 kB) [ 0.000000] .init : 0xc078a000 - 0xc07e0000 ( 344 kB) [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ 0.000000] 0.000000] 0.000000] 0.000000] 0.000000] 0.000000] 0.000000] 0.000000] 0.000000] 0.000122] 0.118957] 0.119110] 0.119171] 0.119598] 0.119689] 0.189056] 0.189941] 0.190155] 0.191284] 0.192382] 0.193511] 0.194030] 0.194152] 0.194305] 0.194305] 0.194335] 0.204650] 0.205657] 0.206512] 0.206634] 0.206787] 0.207092] 0.207122] 0.207122] 0.207153] 0.207305] 0.218994] 0.219787] 0.220336] 0.220916] 0.220977] 0.221008] 0.221008] 0.221038] 0.221038] 0.221252] 0.239868] 0.240081] 0.240264] 0.241210] 0.241546] 0.241729] 0.242218] 0.242309] 0.242462] 0.242462] 0.242492] 0.242492] 0.242492] 0.243041] 0.243072] 0.243469] 0.243835] 0.244049] 0.244445] 0.244598] 0.244689] 0.244720] 0.244720] 0.244750] 0.244964] 0.245239] 0.245269] 0.245269] 0.245269] 0.245544] 0.362121] 0.362365] 0.362426] 0.363342] 0.363586] 0.364654] 0.364685] 0.364746] .data : 0xc07e0000 - 0xc084ba70 ( 431 kB) .bss : 0xc084ba94 - 0xc09a3890 (1376 kB) NR_IRQS:396 IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts Total of 128 interrupts on 1 active controller OMAP clockevent source: GPTIMER2 at 24000000 Hz OMAP clocksource: GPTIMER1 at 32768 Hz sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms Console: colour dummy device 80x30 Calibrating delay loop... 718.02 BogoMIPS (lpj=3590144) pid_max: default: 32768 minimum: 301 Security Framework initialized Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok ftrace: allocating 22068 entries in 65 pages omap_hwmod: pruss: failed to hardreset print_constraints: dummy: NET: Registered protocol family 16 OMAP GPIO hardware version 0.1 omap_mux_init: Add partition: #1: core, flags: 0 omap_i2c.1: alias fck already exists omap2_mcspi.1: alias fck already exists omap2_mcspi.2: alias fck already exists edma.0: alias fck already exists edma.0: alias fck already exists edma.0: alias fck already exists bio: create slab <bio-0> at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb registerd cppi-dma Intr @ IRQ 17 Cppi41 Init Done Qmgr-base(d087a000) dma-base(d0878000) Cppi41 Init Done musb-ti81xx musb-ti81xx: musb0, board_mode=0x13, plat_mode=0x3 musb-ti81xx musb-ti81xx: musb1, board_mode=0x13, plat_mode=0x1 omap_i2c omap_i2c.1: bus 1 rev2.4.0 at 100 kHz tps65910 1-002d: could not be detected Advanced Linux Sound Architecture Driver Version 1.0.24. Bluetooth: Core ver 2.16 NET: Registered protocol family 31 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized Bluetooth: L2CAP socket layer initialized Bluetooth: SCO socket layer initialized Switching to clocksource gp timer musb-hdrc: version 6.0, ?dma?, otg (peripheral+host) musb-hdrc musb-hdrc.0: dma type: dma-cppi41 MUSB0 controller's USBSS revision = 4ea20800 musb-hdrc musb-hdrc.0: USB OTG mode controller at d083c000 using DMA, IRQ 18 musb-hdrc musb-hdrc.1: dma type: dma-cppi41 MUSB1 controller's USBSS revision = 4ea20800 musb-hdrc musb-hdrc.1: MUSB HDRC host driver musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 1 usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: MUSB HDRC host driver usb usb1: Manufacturer: Linux 3.2.0-00244-gcf99001 musb-hcd usb usb1: SerialNumber: musb-hdrc.1 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected musb-hdrc musb-hdrc.1: USB Host mode controller at d083e800 using DMA, IRQ 19 NET: Registered protocol family 2 IP route cache hash table entries: 2048 (order: 1, 8192 bytes) TCP established hash table entries: 8192 (order: 4, 65536 bytes) TCP bind hash table entries: 8192 (order: 3, 32768 bytes) TCP: Hash tables configured (established 8192 bind 8192) TCP reno registered UDP hash table entries: 256 (order: 0, 4096 bytes) UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) NET: Registered protocol family 1 RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. NetWinder Floating Point Emulator V0.97 (double precision) ashmem: initialized VFS: Disk quotas dquot_6.5.2 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) fuse init (API version 7.17) msgmni has been set to 488 io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ 0.365417] 0.366699] 0.976837] 0.980895] 0.988586] 0.996246] 1.003906] 1.011535] 1.019317] 1.030151] 1.036651] 1.040100] 1.046600] 1.053039] 1.111846] 1.116729] 1.131896] 1.135284] 1.138549] 1.144897] 1.152252] 1.160491] 1.168792] 1.177062] 1.185333] 1.193511] 1.201782] 1.211608] 1.216949] 1.241912] 1.249420] 1.256713] 1.270172] 1.275177] 1.280090] 1.290161] 1.297973] 1.302246] 1.307556] 1.324218] 1.327331] 1.334716] 1.338531] 1.342529] 1.349792] 1.411926] 1.419189] 1.481903] 1.489166] 1.552093] 1.556549] 1.560943] 1.565490] 1.572601] 1.576934] 1.581481] 1.585510] 1.631927] 1.638366] 1.645812] 1.649383] 1.657989] 1.662628] 1.667541] 1.672943] 1.679077] 1.685058] 1.690917] 1.697143] 1.700592] 1.706573] 1.712493] 1.720855] 1.726074] 1.732360] 1.737335] 1.743469] 1.748809] 1.755645] 1.760223] 1.766662] 1.772491] 1.779327] 1.785552] Could not set LED4 to fully on omap_uart.0: ttyO0 at MMIO 0x44e09000 (irq = 72) is a OMAP UART0 console [ttyO0] enabled omap_uart.1: ttyO1 at MMIO 0x48022000 (irq = 73) is a OMAP UART1 omap_uart.2: ttyO2 at MMIO 0x48024000 (irq = 74) is a OMAP UART2 omap_uart.3: ttyO3 at MMIO 0x481a6000 (irq = 44) is a OMAP UART3 omap_uart.4: ttyO4 at MMIO 0x481a8000 (irq = 45) is a OMAP UART4 omap_uart.5: ttyO5 at MMIO 0x481aa000 (irq = 46) is a OMAP UART5 [drm] Initialized drm 1.1.0 20060810 brd: module loaded loop: module loaded i2c-core: driver [tsl2550] using legacy suspend method i2c-core: driver [tsl2550] using legacy resume method at24 1-0051: 32768 byte 24c256 EEPROM, writable, 64 bytes/write No daughter card found on AM335x EVM at24 1-0050: 32768 byte 24c256 EEPROM, writable, 64 bytes/write Board name: A335BONE Board version: 00A3 The board is a AM335x Beaglebone. tps65217 1-0024: TPS65217 ID 0x7 version 1.0 print_constraints: DCDC1: 900 <--> 1800 mV at 1800 mV print_constraints: DCDC2: 900 <--> 3300 mV at 1275 mV print_constraints: DCDC3: 900 <--> 1500 mV at 1125 mV print_constraints: LDO1: 1000 <--> 3300 mV at 1800 mV print_constraints: LDO2: 900 <--> 3300 mV at 3300 mV print_constraints: LDO3: 1800 <--> 3300 mV at 3300 mV print_constraints: LDO4: 1800 <--> 3300 mV at 3300 mV omap_hsmmc.0: alias fck already exists omap_i2c.3: alias fck already exists omap_i2c omap_i2c.3: bus 3 rev2.4.0 at 100 kHz at24 3-0054: 32768 byte 24c256 EEPROM, writable, 64 bytes/write IN : bone_setup_display_daughter_board Detected a daughter card on BeagleBone.. BeagleBone LCD7 cape board detected Board Name: BeagleBone LCD7 CAPE............00A1Beagleboardtoys.BB-BONE-LCD7-01.241612LCD70078 Hardware revision: 00A1Beagleboardtoys.BB-BONE-LCD7-01.241612LCD70078 IN : bone_lcd7_lcdc_init da8xx_lcdc.0: alias fck already exists da8xx_lcdc da8xx_lcdc.0: GLCD: Found TFC_S9700RTWV35TR_01B panel Setup LCD display BeagleBone cape: Registering PWM backlight for LCD cape IN : lcd_cape_tsc_init Setup LCD cape touchscreen at24 3-0055: 32768 byte 24c256 EEPROM, writable, 64 bytes/write IN : bone_setup_daughter_board at24 3-0056: 32768 byte 24c256 EEPROM, writable, 64 bytes/write IN : bone_setup_daughter_board at24 3-0057: 32768 byte 24c256 EEPROM, writable, 64 bytes/write IN : bone_setup_daughter_board (hci_tty): inside hci_tty_init (hci_tty): allocated 251, 0 NFC Driver for TI WiLink mtdoops: mtd device (mtddev=name/number) must be supplied omap2-nand driver initializing OneNAND driver initializing CAN device driver interface CAN bus driver for Bosch D_CAN controller 1.0 davinci_mdio davinci_mdio.0: davinci mdio revision 1.6 davinci_mdio davinci_mdio.0: detected phy mask fffffffe davinci_mdio.0: probed davinci_mdio davinci_mdio.0: phy[0]: device 0:00, driver SMSC LAN8710/LAN8720 PPP generic driver version 2.4.2 PPP BSD Compression module registered PPP Deflate Compression module registered usbcore: registered new interface driver cdc_ether usbcore: registered new interface driver cdc_eem usbcore: registered new interface driver dm9601 usbcore: registered new interface driver cdc_subset cdc_ncm: 04-Aug-2011 usbcore: registered new interface driver cdc_ncm usbcore: registered new interface driver cdc_acm cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver usbserial USB Serial support registered for generic usbcore: registered new interface driver usbserial_generic usbserial: USB Serial Driver core USB Serial support registered for GSM modem (1-port) usbcore: registered new interface driver option option: v0.7.2:USB Driver for GSM modems gadget: Mass Storage Function, version: 2009/09/11 gadget: Number of LUNs=1 [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ 1.789367] 1.794708] 1.798645] 1.804260] 1.812103] 1.819183] 1.826751] 1.831939] 1.838836] 1.844085] 1.847991] 1.852813] 1.859344] 1.867980] 1.873077] 1.880279] 1.884338] 1.888336] 1.893493] 1.899475] 1.906707] 1.913269] 1.918273] 1.927124] 1.931762] 1.936767] 1.941680] 1.949249] 1.953704] 1.960205] 1.966064] 1.970611] 1.975463] 1.980468] 1.985412] 1.990844] 1.998291] 2.001403] 2.004974] 2.010253] 2.014892] 2.019927] 2.026550] 2.032196] 2.039459] 2.045867] 2.050659] 2.056457] 2.061340] 2.064910] 2.070343] 2.072998] 2.078826] 2.083892] 2.088562] 2.093231] 2.099792] 2.104461] 2.108886] 2.115386] 2.120513] 2.125885] 2.129791] 2.135345] 2.140808] 2.147155] 2.152160] 2.160156] 2.164672] 2.170318] 2.175201] 2.181854] 2.186248] 2.195190] 2.202362] 2.209289] 2.216705] 2.226165] 2.263000] 2.273986] 2.280212] 2.287170] 2.355194] 2.363769] lun0: LUN: removable file: (no medium) gadget: android_usb ready musb-hdrc musb-hdrc.0: MUSB HDRC host driver musb-hdrc musb-hdrc.0: new USB bus registered, assigned bus number 2 usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: MUSB HDRC host driver usb usb2: Manufacturer: Linux 3.2.0-00244-gcf99001 musb-hcd usb usb2: SerialNumber: musb-hdrc.0 hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected mousedev: PS/2 mouse device common for all mice input: ti-tsc as /devices/platform/omap/ti_tscadc/tsc/input/input0 using rtc device, am33xx-rtc, for alarms omap_rtc am33xx-rtc: rtc core: registered am33xx-rtc as rtc0 am33xx-rtc: already running i2c /dev entries driver Linux video capture interface: v2.00 usbcore: registered new interface driver uvcvideo USB Video Class driver (1.1.1) OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec device-mapper: uevent: version 1.0.3 device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: [email protected] Bluetooth: HCI UART driver ver 2.2 Bluetooth: HCI H4 protocol initialized Bluetooth: HCILL protocol initialized Bluetooth: Bluetooth Driver for TI WiLink - Version 1.0 cpuidle: using governor ladder cpuidle: using governor menu usbcore: registered new interface driver usbhid usbhid: USB HID core driver logger: created 256K log 'log_main' logger: created 256K log 'log_events' logger: created 256K log 'log_radio' logger: created 256K log 'log_system' usbcore: registered new interface driver snd-usb-audio ALSA device list: No soundcards found. oprofile: hardware counters not available oprofile: using timer interrupt. Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (3906 buckets, 15624 max) ctnetlink v0.93: registering with nfnetlink. NF_TPROXY: Transparent proxy support initialized, version 4.1.0 NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd. xt_time: kernel timezone is -0000 ip_tables: (C) 2000-2006 Netfilter Core Team arp_tables: (C) 2002 David S. Miller TCP cubic registered NET: Registered protocol family 10 Mobile IPv6 ip6_tables: (C) 2000-2006 Netfilter Core Team IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 NET: Registered protocol family 15 can: controller area network core (rev 20090105 abi 8) NET: Registered protocol family 29 can: raw protocol (rev 20090105) can: broadcast manager protocol (rev 20090105 t) Bluetooth: RFCOMM TTY layer initialized Bluetooth: RFCOMM socket layer initialized Bluetooth: RFCOMM ver 1.11 Bluetooth: BNEP (Ethernet Emulation) ver 1.3 Bluetooth: BNEP filters: protocol multicast Bluetooth: HIDP (Human Interface Emulation) ver 1.2 Registering the dns_resolver key type VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 ThumbEE CPU extension supported. mux: Failed to setup hwmod io irq -22 Power Management for AM33XX family Trying to load am335x-pm-firmware.bin (60 secs timeout) Copied the M3 firmware to UMEM Cortex M3 Firmware Version = 0x181 clock: disabling unused clocks to save power Detected MACID=40:5f:c2:76:a5:8f input: gpio-keys as /devices/platform/gpio-keys/input/input1 omap_rtc am33xx-rtc: setting system clock to 2000-01-01 00:02:54 UTC (946684974) Waiting for root device /dev/mmcblk0p2... mmc0: host does not support reading read-only switch. assuming write-enable. mmc0: new high speed SDHC card at address 1234 mmcblk0: mmc0:1234 SA04G 3.63 GiB mmcblk0: p1 p2 p3 p4 EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) VFS: Mounted root (ext4 filesystem) on device 179:2. [ 2.370513] [ 2.402984] [ 2.496582] [ 3.231964] [ 3.282623] [ 3.305572] [ 3.315307] [ 3.320343] [ 3.325317] [ 3.333801] [ 3.499786] [ 3.587615] [ 3.593383] root@android:/ [ 3.679504] [ 3.686401] [ 3.691589] [ 3.877136] [ 137.573547] [ 139.822021] [ 139.828186] [ 139.840606] [ 140.338256] [ 140.340576] [ 356.130798] [ 356.135803] [ 356.141906] [ 359.533599] Freeing init memory: 344K init (1): /proc/1/oom_adj is deprecated, please use /proc/1/oom_score_adj instead. init: cannot open '/initlogo.rle' EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: nomblk_io_submit,errors=panic init: cannot find '/system/etc/install-recovery.sh', disabling 'flash_recovery' android_usb: already disabled android_usb: already disabled android_usb: already disabled adb_bind_config adb_bind_config adb_open android_work: sent uevent USB_STATE=CONNECTED android_work: sent uevent USB_STATE=DISCONNECTED # [ 3.627471] Disabling lock debugging due to kernel taint android_work: sent uevent USB_STATE=CONNECTED gadget: high-speed config #1: android android_work: sent uevent USB_STATE=CONFIGURED warning: `rild' uses 32-bit capabilities (legacy support in use) request_suspend_state: wakeup (3->0) at 137540860249 (2000-01-01 00:05:09.841582180 UTC) net eth0: CPSW phy found : id is : 0x7c0f1 PHY 0:01 not found ADDRCONF(NETDEV_UP): eth0: link is not ready acc_open acc_release binder: 738: binder_alloc_buf, no vma binder: 327:545 transaction failed 29201, size 4-0 binder: send failed reply for transaction 18810 to 738:738 init: sys_prop: permission denied uid:1003 name:service.bootanim.exit root@android:/ # root@android:/ # root@android:/ #