MN101C589 , MN101C58A Type MN101C589 MN101C58A ROM (×× 8-bit) 24 K 32 K RAM (×× 8-bit) 1.5 K 1.5 K Package Minimum Instruction Execution Time Interrupts Timer Counter LQFP064-P-1414 *Lead-free 0.1 µs (at 4.5 V to 5.5 V, 20 MHz) 0.25 µs (at 2.7 V to 5.5 V, 8 MHz)*1 62.5 µs (at 2.0 V to 5.5 V, 32 kHz)*1,2 1 * The lower limit for operation guarantee for flash memory built-in type is 4.5 V. *2 The lower limit for operation guarantee for EPROM built-in type is 2.3 V. • RESET • Watchdog • External 0 • External 1 • External 2 • External 4 (key interrupt dedicated) • Timer 0 • Timer 1 • Timer 2 • Timer 3 • Timer 6 • Time base • Timer 7 (2 systems) • Timer 8 (2 systems) • Serial 0 (2 systems) • A/D conversion finish Timer counter 0 : 8-bit × 1 (square-wave/8-bit PWM output, event count, generation of remote control carrier, simple pulse width measurement) (square-wave/PWM output to large current terminal P50 possible) Clock source ····················· 1/2, 1/4 of system clock frequency; 1/1, 1/4, 1/16, 1/32, 1/64 of OSC oscillation clock frequency; 1/1 of XI oscillation clock frequency; external clock input Interrupt source ················ coincidence with compare register 0 Timer counter 1 : 8-bit × 1 (square-wave output, event count, synchronous output event) Clock source ····················· 1/2, 1/8 of system clock frequency; 1/1, 1/4, 1/16, 1/8192, 1/32768 of OSC oscillation clock frequency; 1/1 of XI oscillation clock frequency; external clock input Interrupt source ················ coincidence with compare register 1 Timer counter 0, 1 can be cascade-connected. Timer counter 2 : 8-bit × 1 (square-wave output, additional pulse type 10-bit PWM output, event count, synchronous output event, simple pulse width measurement) (square-wave/PWM output to large current terminal P52 possible) Clock source ····················· 1/2, 1/4 of system clock frequency; 1/1, 1/4, 1/16, 1/32, 1/64 of OSC oscillation clock frequency; 1/1 of XI oscillation clock frequency; external clock input Interrupt source ················ coincidence with compare register 2 Timer counter 3 : 8-bit × 1 (square-wave output, event count, generation of remote control carrier, serial 0 baud rate timer) Clock source ····················· 1/2, 1/8 of system clock frequency; 1/1, 1/4, 1/16, 1/64, 1/128 of OSC oscillation clock frequency; 1/1 of XI oscillation clock frequency; external clock input Interrupt source ················ coincidence with compare register 3 Timer counter 2, 3 can be cascade-connected. Timer counter 6 : 8-bit freerun timer Clock source ····················· 1/1 of system clock frequency; 1/1, 1/4096, 1/8192 of OSC oscillation clock frequency; 1/1, 1/4096, 1/8192 of XI oscillation clock frequency Interrupt source ················ coincidence with compare register 6 Timer counter 7 : 16-bit × 1 (square-wave output, IGBT/16-bit PWM output (cycle / duty continuous variable), event count, synchronous output evevt, pulse width measurement, input capture) (square-wave/PWM output to large current terminal P51 possible) Clock source ····················· 1/1, 1/2, 1/4, 1/16 of system clock frequency; 1/1, 1/2, 1/4, 1/16 of OSC oscillation clock frequency; 1/1, 1/2, 1/4, 1/16 of external clock input frequency Interrupt source ················ coincidence with compare register 7 (2 lines) Timer counter 8: 16 bit × 1 (square-wave/16-bit PWM output [duty continuous variable], event count, pulse width measurement, input capture) (square-wave/PWM output to large current terminal P53 possible) 1 MAD00014DEM MN101C589 , MN101C58A Timer Counter (Continue) Clock source ····················· 1/1, 1/2, 1/4, 1/16, 1/128 of system clock frequency; 1/1, 1/2, 1/4, 1/16, 1/128 of OSC oscillation clock frequency; 1/1, 1/2, 1/4, 1/16 of external clock input frequency Interrupt source ················ coincidence with compare register 8 (2 lines) Timer counters 7, 8 can be cascade-connected. (square-wave output, PWM, input capture, pulse width measurement is possible as a 32-bit timer.) Time base timer (one-minute count setting) Clock source ····················· 1/1 of OSC oscillation clock frequency; 1/1 of XI oscillation clock frequency Interrupt source ················ 1/128, 1/256, 1/512, 1/1024, 1/8192, 1/32768, of clock source frequency Watchdog timer Interrupt source ················ 1/65536, 1/262144, 1/1048576 of system clock frequency Serial 0 : synchronous type/UART (full-duplex) × 1 Clock source ····················· 1/2, 1/4 of system clock frequency; pulse output of timer counter 3; 1/2, 1/4, 1/16, 1/64 of OSC oscillation clock frequency Serial Interface I/O Pins I/O 46 • Common use • Specified pull-up resistor available • Input/output selectable (bit unit) Input 3 • Common use • Specified pull-up resistor available A/D Inputs 10-bit × 8-ch. (with S/H) LCD 24 segments × 4 commons (static, 1/2, 1/3, or 1/4 duty) LCD power supply separated from VDD (usable if VDD ≤ VLCD ≤ 5.5 V) LCD power step-up circuit contained (3/2, 2 and 3 times) LCD power shunt resistance contained Special Ports Buzzer output, remote control carrier signal output, high-current drive port Electrical Characteristics Supply current Limit Parameter Symbol Condition Unit min Operating supply current Supply current at HALT Supply current at STOP typ max IDD1 fosc = 20 MHz, VDD = 5 V 25 60 mA IDD2 fosc = 8 MHz, VDD = 5 V 10 25 mA IDD3 fx = 32 kHz, VDD = 3 V 30 100 µA IDD4 fx = 32 kHz, VDD = 3 V, Ta = 25°C 4 8 µA IDD5 fx = 32 kHz, VDD = 3 V, Ta = −40°C to +85°C 30 µA IDD6 VDD = 5 V, Ta = 25°C 2 µA IDD7 VDD = 5 V, Ta = −40°C to +85°C 50 µA See the next page for pin assignment and support tool. MAD00014DEM 2 SEG12,P73 SEG13,P72 SEG14,P71 SEG15,P70 SEG16/KEY7/P67/SDO7 SEG17/KEY6/P66/SDO6 SEG18/KEY5/P65/SDO5 SEG19/KEY4/P64/SDO4 SEG20/KEY3/P63/SDO3 SEG21/KEY2/P62/SDO2/SBT0B SEG22/KEY1/P61/SDO1/SBI0B/RXDB SEG23/KEY0/P60/SDO0/SBO0B/TXDB P22,IRQ2 P21,IRQ1,ACZ1 P20,IRQ0,ACZ0 P15,TM8IO 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 Pin Assignment SEG11,P74 49 32 TM7IO,P14 SEG10,P75 50 31 TM3IO,P13 SEG9,P76 51 30 TM2IO,P12 SEG8,P77 52 29 TM1IO,P11 SEG7,P80 53 28 RMOUT,TM0IO,P10 SEG6,P81 54 27 AN7/BUZZER/P06 SEG5,P82 55 26 AN6/SBT0A/P02 SEG4,P83 56 25 AN5/RXDA/SBI0A/P01 SEG3,P84 57 24 AN4/TXDA/SBO0A/P00 SEG2,P85 58 23 VDD SEG1,P86 59 22 AN3/PA3 SEG0,P87 60 21 AN2/PA2 COM0,P30 61 20 AN1/PA1 COM1,P31 62 19 AN0/PA0 COM2,P32 63 18 VREF+ COM3,P33 64 17 NRST,P27 12 13 14 15 16 OSC1 ATRST XI XO VDD 9 TM8O,LED3,P53 11 8 TM2O, LED2,P52 OSC2 7 TM7O,LED1,P51 10 6 TM0O,LED0,P50 VSS 5 C2 3 VLCIN3/VLC3 4 2 C1 1 VLC1 VLCIN2/VLC2 MN101C589 MN101C58A LQFP064-P-1414 *Lead-free Support Tool In-circuit Emulator PX-ICE101C / D + PX-PRB101C58-LQFP064-P-1414-M EPROM Built-in Type Type MN101CP58A ROM (× 8-bit) 32 K RAM (× 8-bit) 1.5 K Minimum instruction execution time 0.1 µs (at 4.5 V to 5.5 V, 20 MHz) 0.25 µs (at 2.7 V to 5.5 V, 8 MHz) 62.5 µs (at 2.3 V to 5.5 V, 32 kHz) Flash Memory Built-in Type Package LQFP064-P-1414 *Lead-free Type MN101CF58D [ES (Engineering Sample) available] ROM (× 8-bit) 64 K RAM (× 8-bit) 2K Minimum instruction execution time 0.1 µs (at 4.5 V to 5.5 V, 20 MHz) 0.25 µs (at 4.5 V to 5.5 V, 8 MHz) 62.5 µs (at 4.5 V to 5.5 V, 32 kHz) Package 3 LQFP064-P-1414 *Lead-free MAD00014DEM MN101C589 , MN101C58A MAD00014DEM 4 Request for your special attention and precautions in using the technical information and semiconductors described in this material (1) An export permit needs to be obtained from the competent authorities of the Japanese Government if any of the products or technologies described in this material and controlled under the "Foreign Exchange and Foreign Trade Law" is to be exported or taken out of Japan. (2) The technical information described in this material is limited to showing representative characteristics and applied circuits examples of the products. It neither warrants non-infringement of intellectual property right or any other rights owned by our company or a third party, nor grants any license. (3) We are not liable for the infringement of rights owned by a third party arising out of the use of the product or technologies as described in this material. (4) The products described in this material are intended to be used for standard applications or general electronic equipment (such as office equipment, communications equipment, measuring instruments and household appliances). Consult our sales staff in advance for information on the following applications: • Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the products may directly jeopardize life or harm the human body. • Any applications other than the standard applications intended. (5) The products and product specifications described in this material are subject to change without notice for modification and/or improvement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product Standards in advance to make sure that the latest specifications satisfy your requirements. (6) When designing your equipment, comply with the guaranteed values, in particular those of maximum rating, the range of operating power supply voltage, and heat radiation characteristics. Otherwise, we will not be liable for any defect which may arise later in your equipment. Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products. (7) When using products for which damp-proof packing is required, observe the conditions (including shelf life and amount of time let standing of unsealed items) agreed upon when specification sheets are individually exchanged. (8) This material may be not reprinted or reproduced whether wholly or partially, without the prior written permission of Matsushita Electric Industrial Co., Ltd. 2002 JUL