8 6 7 4 5 3 2 ALUMINUM COMPATIBLE LASER WELDABLE 50 OHM FEEDTHROUGH SMA ADAPTABLE, .012, .015, .020 DIAMETER CENTER CONTACT D REV • CONFIGURATION FOR INTERFACING TO PANEL JACK ADAPTER (SRI CONNECTOR GAGE PART NUMBER 21-150-1500-0, INSTALL AT 13 1 LB-IN) SRIFT501 DOCUMENT REVISIONS DATE CHANGE NO. CFG APPROVAL - INIT RLSE 2008-08-06 J. PETRI A DCN000375 9/26/2008 J. PETRI B DCN000567 10/15/2009 J.PETRI C DCN000654 5/18/2010 J. PETRI • DESIGNED TO LASER WELD INTO AN ELECTRONIC CHASSIS D • INDUSTRY STANDARD NICKEL-IRON-COBALT ALLOY CONTACT WITH CORNING 7070 EQUIVALENT GLASS • INTEGRAL RF GROUNDING TAB FOR EXCELLENT PERFORMANCE OVER TEMPERATURE 1. LEAK RATE: LESS THAN OR EQUAL TO 1X10E-9 CC/SEC He AT ONE ATMOSPHERE DIFFERENTIAL PRESSURE. 2. NOMINAL IMPEDANCE: 50 OHMS 3. INTERFACE IN ACCORDANCE WITH MIL-STD-348, SMA. 4. MATES WITH .427 MIN LONG PANEL JACK. C C 5. MATERIALS: PIN: NICKEL-IRON-COBALT ALLOY IN ACCORDANCE WITH ASTM F15. DIELECTRIC: CORNING 7070 EQUIVALENT GLASS (LOW LOSS, MATCHED SEAL). SHELL (WELD FLANGE): ALUMINUM ALLOY 4047 IN ACCORDANCE WITH AWS A5.8. RF GROUNDING SPRING: BERYLLIUM-COPPER ALLOY 172/173 IN ACCORDANCE WITH ASTM B 194 (NICKEL/GOLD PLATED) VIEWS FOR REFEREENCE ONLY C 6. FINISH: EXCEPT WELD FLANGE: NICKEL PLATE PER QQ-N-290, CLASS 2, .000100/.000250 THICK GOLD PLATE PER ASTM B488-01, TYPE III, CODE A, .000050/.000100 THICK. C 7. ORDERING INSTRUCTIONS: SPECIFY BASE NUMBER FOLLOWED BY DASH NUMBERS INDICATING PIN DIAMETER, D, PIN LENGTH, L, AND DIELECTRIC TYPE: .235 EXAMPLE: SRIFT501 - 015 - 045 - A L .003 .319 MAX OVER KNURL A=GROUNDING SPRING FOR AIR DIELECTRIC T=GROUNDING SPRING FOR TEFLON DIELECTRIC PIN LENGTH, L=.045 (.035 MIN) D .001 PIN DIAMETER, D=.015 (.012, .015, OR .020) BASE NUMBER PIN B WELD FLANGE RF GROUNDING SPRING, SHIPPED UNINSTALLED PART NUMBER SRIFT501-GS1, D=.012, AIR DIELECTRIC PART NUMBER SRIFT501-GS2, D=.015, AIR DIELECTRIC PART NUMBER SRIFT501-GS3, D=.020, AIR DIELECTRIC PART NUMBER SRIFT501-GS4, D=.012, TEFLON DIELECTRIC PART NUMBER SRIFT501-GS5, D=.015, TEFLON DIELECTRIC PART NUMBER SRIFT501-GS6, D=.020, TEFLON DIELECTRIC SHELL C C .001 B .001 THRU (AIR DIELECTRIC) AS REQUIRED (TEFLON DIELECTRIC) .303 .001 SHOWN .3150 .0005 .100 .005 .230±.002 AS REQUIRED .040 MIN UNPLATED (TEFLON DIELECTRIC, OPTIONAL) UNPLATED THRU (AIR DIELECTRIC) PART NUMBER D B C SRIFT501-012-XXX-A .012 .0280 .0390 .0390 SRIFT501-012-XXX-T .012 .0280 SRIFT501-015-XXX-A .015 .0345 .0490 SRIFT501-015-XXX-T .015 .0345 .0490 SRIFT501-020-XXX-A .020 .0460 .0650 SRIFT501-020-XXX-T .020 .0460 .0650 UNLESS OTHERWISE SPECIFIED A .003 MAX BRK DIMENSIONING IAW ASME Y14.5M-1994 DIMENSIONS APPLY AFTER PROCESSES DIMENSIONS IAW US CUSTOMARY UNITS .X .1, .XX .01, .XXX .005, .5 .010 MAX OUTSIDE R, .005 MAX INSIDE R 125 RMS SURFACE FINISH O THIRD ANGLE PROJECTION RECOMMENDED HOLE DETAIL SRI HERMETICS TITLE CONNECTOR, SMA, ALUMINUM LASER WELDABLE SIZE DOCUMENT 7 6 5 4 3 SRIFT501 A SCALE FORM 300067 REV - (321) 254-4067 WWW.SRIHERMETICS.COM 3:1 2 CAGE CODE 3PJY7 SHEET 1 REV C 1 OF 1 B A