LT3580 - Boost/Inverting DC/DC Converter with 2A Switch, Soft-Start, and Synchronization

LT3580
Boost/Inverting DC/DC
Converter with 2A Switch,
Soft-Start, and Synchronization
FEATURES
DESCRIPTION
n
The LT®3580 is a PWM DC/DC converter containing an
internal 2A, 42V switch. The LT3580 can be configured
as either a boost, SEPIC or inverting converter. Capable
of generating 12V at 550mA or –12V at 350mA from a
5V input, the LT3580 is ideal for many local power supply
designs.
n
n
n
n
n
n
n
n
n
n
2A Internal Power Switch
Adjustable Switching Frequency
Single Feedback Resistor Sets VOUT
Synchronizable to External Clock
High Gain SHDN Pin Accepts Slowly Varying
Input Signals
Wide Input Voltage Range: 2.5V to 32V
Low VCESAT Switch: 300mV at 1.5A (Typical)
Integrated Soft-Start Function
Easily Configurable as a Boost or Inverting Converter
User Configurable Undervoltage Lockout (UVLO)
Tiny 8-Lead 3mm × 3mm DFN and 8-Lead MSOP
Packages
APPLICATIONS
n
n
n
n
n
The LT3580 has an adjustable oscillator, set by a resistor
from the RT pin to ground. Additionally, the LT3580 can
be synchronized to an external clock. The free running or
synchronized switching frequency range of the part can
be set between 200kHz and 2.5MHz.
The LT3580 also features innovative SHDN pin circuitry
that allows for slowly varying input signals and an adjustable undervoltage lockout function.
Additional features such as frequency foldback and
soft-start are integrated. The LT3580 is available in tiny
3mm × 3mm 8-lead DFN and 8-lead MSOP packages.
VFD Bias Supplies
TFT-LCD Bias Supplies
GPS Receivers
DSL Modems
Local Power Supply
L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks of Linear
Technology Corporation. ThinSOT is a trademark of Linear Technology Corporation. All other
trademarks are the property of their respective owners.
TYPICAL APPLICATION
1.2MHz, 5V to 12V Boost Converter Achieves Over 88% Efficiency
Efficiency and Power Loss
95
4.2μH
SHDN
GND
130k
LT3580
RT
FB
VC
SYNC
2.2μF
75k
1000
85
10μF
SW
SS
10k
0.1μF
1nF
80
800
75
600
70
65
400
POWER LOSS (mW)
VIN
1200
90
EFFICIENCY (%)
VIN
5V
VOUT
12V
550mA
60
200
3580 TA01
55
50
0
0
100
200
300
400
LOAD CURRENT (mA)
500
600
3580 TA01b
3580fg
1
LT3580
ABSOLUTE MAXIMUM RATINGS
(Note 1)
VIN Voltage ................................................. –0.3V to 32V
SW Voltage ................................................ –0.4V to 42V
RT Voltage ................................................... –0.3V to 5V
SS and FB Voltage .................................... –0.3V to 2.5V
VC Voltage ................................................... –0.3V to 2V
SHDN Voltage ............................................ –0.3V to 32V
SYNC Voltage............................................ –0.3V to 5.5V
Operating Junction Temperature Range
LT3580E (Notes 2, 5)......................... –40°C to 125°C
LT3580I (Notes 2, 5).......................... –40°C to 125°C
LT3580H (Notes 2, 5) ........................–40°C to 150°C
LT3580MP (Notes 2, 5) ..................... –55°C to 125°C
Storage Temperature Range ..................–65°C to 150°C
PIN CONFIGURATION
TOP VIEW
TOP VIEW
FB 1
VC 2
VIN 3
9
GND
SW 4
8
SYNC
7
SS
6
RT
5
SHDN
FB
VC
VIN
SW
1
2
3
4
9
GND
8
7
6
5
SYNC
SS
RT
SHDN
MS8E PACKAGE
8-LEAD PLASTIC MSOP
DD PACKAGE
8-LEAD (3mm s 3mm) PLASTIC DFN
TJMAX = 125°C, θJA = 43°C/W
EXPOSED PAD (PIN 9) IS GND, MUST BE SOLDERED TO PCB
θJA = 35°C/W TO 40°C/W
EXPOSED PAD (PIN 9) IS GND, MUST BE SOLDERED TO PCB
ORDER INFORMATION
LEAD FREE FINISH
TAPE AND REEL
PART MARKING*
PACKAGE DESCRIPTION
TEMPERATURE RANGE
LT3580EDD#PBF
LT3580EDD#TRPBF
LCXY
8-Lead (3mm × 3mm) Plastic DFN
– 40°C to 125°C
LT3580IDD#PBF
LT3580IDD#TRPBF
LCXY
8-Lead (3mm × 3mm) Plastic DFN
– 40°C to 125°C
LT3580EMS8E#PBF
LT3580EMS8E#TRPBF
LTDCJ
8-Lead Plastic MSOP
– 40°C to 125°C
LT3580IMS8E#PBF
LT3580IMS8E#TRPBF
LTDCJ
8-Lead Plastic MSOP
– 40°C to 125°C
LT3580HMS8E#PBF
LT3580HMS8E#TRPBF
LTDCJ
8-Lead Plastic MSOP
– 40°C to 150°C
LT3580MPMS8E#PBF
LT3580MPMS8E#TRPBF
LTDCJ
8-Lead Plastic MSOP
– 55°C to 125°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
Consult LTC Marketing for information on non-standard lead based finish parts.
For more information on lead free part marking, go to: http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/
3580fg
2
LT3580
ELECTRICAL CHARACTERISTICS
The l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VIN = 5V, VSHDN = VIN unless otherwise noted. (Note 2)
PARAMETER
Operating Voltage Range
Positive Feedback Voltage
Negative Feedback Voltage
Positive FB Pin Bias Current
Negative FB Pin Bias Current
CONDITIONS
MIN
TYP
MAX
UNITS
l
2.5
1.195
0
81
1.215
5
83.3
32
1.230
12
85
V
V
mV
μA
l
l
81
81
85.5
86
μA
μA
μmhos
l
l
l
VFB = Positive Feedback Voltage, Current Into Pin
VFB = Negative Feedback Voltage, Current Out of Pin
(LT3580E, LT3580I, LT3580MP)
(LT3580H)
Error Amplifier Transconductance
Error Amplifier Voltage Gain
Quiescent Current
Quiescent Current in Shutdown
Reference Line Regulation
Switching Frequency, fOSC
Switching Frequency in Foldback
Switching Frequency Set Range
SYNC High Level for Synchronization
SYNC Low Level for Synchronization
SYNC Clock Pulse Duty Cycle
Recommended Minimum SYNC Ratio fSYNC/fOSC
Minimum Off-Time
Minimum On-Time
Switch Current Limit
Switch VCESAT
Switch Leakage Current
Soft-Start Charging Current
SHDN Minimum Input
Voltage High
SHDN Input Voltage Low
SHDN Pin Bias Current
VSHDN = 2.5V, Not Switching
VSHDN = 0V
2.5V ≤ VIN ≤ 32V
RT = 45.3k (LT3580E, LT3580I, LT3580H)
RT = 45.3k (LT3580MP)
RT = 464k (LT3580E, LT3580I, LT3580H)
RT = 464k (LT3580MP)
Compared to Normal fOSC
SYNCing or Free Running
l
l
l
l
1.8
1.8
180
180
l
200
1.3
l
83.3
83.3
230
70
1
0
0.01
2
2
200
200
1/4
35
Minimum Duty Cycle (Note3) (LT3580E, LT3580I, LT3580H)
Minimum Duty Cycle (Note3) (LT3580MP)
Maximum Duty Cycle (Notes 3, 4) (LT3580E, LT3580I,
LT3580MP)
Maximum Duty Cycle (Notes 3, 4) (LT3580H)
ISW = 1.5A
VSW = 5V
VSS = 0.5V
Active Mode, SHDN Rising (LT3580E, LT3580I)
Active Mode, SHDN Rising (LT3580H, LT3580MP)
Active Mode, SHDN Falling (LT3580E, LT3580I)
Active Mode, SHDN Falling (LT3580H, LT3580MP)
Shutdown Mode
VSHDN = 3V
VSHDN = 1.3V
VSHDN = 0V
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: The LT3580E is guaranteed to meet performance specifications
from 0°C to 125°C junction temperature. Specifications over the –40°C
to 125°C operating junction temperature range are assured by design,
characterization and correlation with statistical process controls. The
LT3580I is guaranteed over the full –40°C to 125°C operating junction
temperature range. The LT3580H is guaranteed over the full –40°C to
l
l
l
2.2
2.15
1.6
l
1.55
l
4
1.27
1.25
1.24
1.22
l
l
l
l
3/4
60
100
2.5
2.2
1.9
1.9
300
0.01
6
1.32
1.32
1.29
1.29
l
9.7
0.4
65
2.8
2.8
2.6
ns
ns
A
A
A
2500
l
VSYNC = 0V to 2V
V/V
mA
μA
%/V
MHz
MHz
kHz
kHz
Ratio
kHz
V
V
%
1.5
1
0.05
2.2
2.25
220
225
40
11.6
0
2.6
1
8
1.38
1.4
1.33
1.35
0.3
60
13.4
0.1
A
mV
μA
μA
V
V
V
V
V
μA
μA
μA
150°C operating junction temperature range. The LT3580MP is guaranteed
over the full –55°C to 125°C operating junction temperature range.
Operating lifetime is derated at junction temperatures greater than 125°C.
Note 3: Current limit guaranteed by design and/or correlation to static test.
Note 4: Current limit measured at equivalent switching frequency of 2.5MHz.
Note 5: This IC includes overtemperature protection that is intended
to protect the device during momentary overload conditions. Junction
temperature will exceed 150°C when overtemperature protection is active.
Continuous operation above the specified maximum operating junction
temperature may impair device reliability.
3580fg
3
LT3580
TYPICAL PERFORMANCE CHARACTERISTICS
Switch Current Limit at 1MHz
TA = 25°C unless otherwise specified
Switch Current Limit at Minimum
Duty Cycle
Switch Saturation Voltage
400
2.5
350
SATURATION VOLTAGE (mV)
2.0
1.5
1.0
300
SWITCH CURRENT (A)
SWITCH CURRENT LIMIT (A)
2.5
250
200
150
2.0
1.5
1.0
100
0.5
0.5
50
0
10
20
30
40 50 60 70
DUTY CYCLE (%)
80
0
90
0
1
0.5
1.5
SWITCH CURRENT (A)
0
2
3580 G01
400
600
800
SS VOLTAGE (mV)
1000
1200
3580 G03
Switching Waveforms for
Figure 14 Circuit
Positive Feedback Voltage
1.24
3.0
2.5
VOUT
50mV/DIV
AC COUPLED
1.23
2.0
FB VOLTAGE (V)
SWITCH CURRENT LIMIT (A)
200
3580 G02
Switch Current Limit at Minimum
Duty Cycle
1.5
1.0
1.22
VSW
10V/DIV
1.21
1.20
0.5
IL
0.5A/DIV
0
–50
0
50
TEMPERATURE (°C)
100
1.19
–50
–25
50
25
0
75
TEMPERATURE (°C)
100
3580 G04
1.9
1.7
1.5
1.1
–50
RT = 75k
50
0
TEMPERATURE (°C)
100
3580 G07
3580 G06
Internal UVLO
2.40
1
2.38
TA = –35°C
2.36
TA = 100°C
2.34
TA = 25°C
VIN VOLTAGE (V)
2.1
NORMALIZED OSCILLATOR FREQUENCY (F/FNOM)
RT = 35.7k
2.3
1.3
200ns/DIV
Oscillator Frequency During
Soft-Start
2.7
2.5
125
3580 G05
Oscillator Frequency
FREQUENCY (MHz)
0
2.32
2.30
1/2
2.28
1/3
1/4
2.26
2.24
INVERTING
CONFIGURATIONS
BOOSTING
CONFIGURATIONS
2.22
0
0
0.2
0.4
0.6
0.8
FB VOLTAGE (V)
1.0
1.2
3580 G08
2.20
–50
50
0
TEMPERATURE (°C)
100
3580 G09
3580fg
4
LT3580
TYPICAL PERFORMANCE CHARACTERISTICS
SHDN Pin Current
TA = 25°C unless otherwise specified
SHDN Pin Current
30
300
25
250
Active/Lockout Threshold
1.40
20
15
10
–50°C
5
100°C
0.5
1.36
20°C
200
100°C
150
100
1.34
1.32
SHDN RISING
1.30
1.28
1.26
SHDN FALLING
1.24
50
1.22
20°C
0
0
1.38
SHDN VOLTAGE (V)
SHDN PIN CURRENT (μA)
SHDN PIN CURRENT (μA)
–50°C
1
1.5
SHDN VOLTAGE (V)
2
0
0
5
20
15
25
10
SHDN VOLTAGE (V)
3580 G10
30
3580 G11
1.20
–50
50
0
TEMPERATURE (°C)
100
3580 G12
PIN FUNCTIONS
FB (Pin 1): Positive and Negative Feedback Pin. For a
boost or inverting converter, tie a resistor from the FB pin
to VOUT according to the following equations:
RFB =
RFB =
( VOUT − 1.215) ; Boost or SEPIC Converter
(
83.3 • 10 −6
VOUT + 5mV
83.3 • 10 −6
) ; Inverting Converter
VC (Pin 2): Error Amplifier Output Pin. Tie external
compensation network to this pin.
VIN (Pin 3): Input Supply Pin. Must be locally bypassed.
SW (Pin 4): Switch Pin. This is the collector of the internal
NPN Power switch. Minimize the metal trace area connected to this pin to minimize EMI.
RT (Pin 6): Timing Resistor Pin. Adjusts the switching
frequency. Place a resistor from this pin to ground to set
the frequency to a fixed free running level. Do not float
this pin.
SS (Pin 7): Soft-Start Pin. Place a soft-start capacitor here.
Upon start-up, the SS pin will be charged by a (nominally)
275k resistor to about 2.2V.
SYNC (Pin 8): To synchronize the switching frequency to
an outside clock, simply drive this pin with a clock. The
high voltage level of the clock needs to exceed 1.3V, and
the low level should be less 0.4V. Drive this pin to less than
0.4V to revert to the internal free running clock. See the
Applications Information section for more information.
GND (Exposed Pad Pin 9): Ground. Exposed pad must
be soldered directly to local ground plane.
SHDN (Pin 5): Shutdown Pin. In conjunction with the
UVLO (undervoltage lockout) circuit, this pin is used
to enable/disable the chip and restart the soft-start
sequence. Drive below 1.24V (LT3580E, LT3580I) or 1.22V
(LT3580H, LT3580MP) to disable the chip. Drive above
1.38V (LT3580E, LT3580I) or 1.40V (LT3580H, LT3580MP)
to activate chip and restart the soft-start sequence. Do
not float this pin.
3580fg
5
LT3580
BLOCK DIAGRAM
RC
VIN
CSS
7
SHDN
5
1.3V
–
+
CC
2
SS
CIN
VC
DISCHARGE
DETECT
L1
275k
UVLO
SR2
SOFTSTART
R
Q
VIN
3
4
ILIMIT
COMPARATOR
–
Q2
A3
1.215V
REFERENCE
+
R
S
+
∑
A1
–
A4
+
A2
FREQUENCY
FOLDBACK
RFB
0.01Ω
–
RAMP
GENERATOR
GND
FB
14.6k
C1
Q1
Q
+
1
VOUT
SR1
DRIVER
S
14.6k
D1
SW
VC
9
÷N ADJUSTABLE
OSCILLATOR
–
SYNC
BLOCK
SYNC
8
6
RT
RT
3580 BD
OPERATION
The LT3580 uses a constant-frequency, current mode control scheme to provide excellent line and load regulation.
Refer to the Block Diagram which shows the LT3580 in a
boost configuration. At the start of each oscillator cycle,
the SR latch (SR1) is set, which turns on the power switch,
Q1. The switch current flows through the internal current
sense resistor generating a voltage proportional to the
switch current. This voltage (amplified by A4) is added
to a stabilizing ramp and the resulting sum is fed into the
positive terminal of the PWM comparator A3. When this
voltage exceeds the level at the negative input of A3, the SR
latch is reset, turning off the power switch. The level at the
negative input of A3 (VC pin) is set by the error amplifier A1
(or A2) and is simply an amplified version of the difference
between the feedback voltage (FB pin) and the reference
voltage (1.215V or 5mV depending on the configuration).
In this manner, the error amplifier sets the correct peak
current level to keep the output in regulation.
The LT3580 has a novel FB pin architecture that can be
used for either boost or inverting configurations. When
configured as a boost converter, the FB pin is pulled up
to the internal bias voltage of 1.215V by the RFB resistor
connected from VOUT to FB. Comparator A2 becomes
inactive and comparator A1 performs the inverting
amplification from FB to VC. When the LT3580 is in an
inverting configuration, the FB pin is pulled down to 5mV
by the RFB resistor connected from VOUT to FB. Comparator
A1 becomes inactive and comparator A2 performs the
noninverting amplification from FB to VC.
3580fg
6
LT3580
OPERATION
SEPIC Topology
The LT3580 can be configured as a SEPIC (single-ended
primary inductance converter). This topology allows for
the input to be higher, equal, or lower then the desired
output voltage. Output disconnect is inherently built into
the SEPIC topology, meaning no DC path exists between the
input and output. This is useful for applications requiring
the output to be disconnected from the input source when
the circuit is in shutdown.
Inverting Topology
The LT3580 can also work in a dual inductor inverting
topology. The part’s unique feedback pin allows for the
inverting topology to be built by simply changing the
connection of external components. This solution results
in very low output voltage ripple due to inductor L2 in
series with the output. Abrupt changes in output capacitor
current are eliminated because the output inductor delivers current to the output during both the off-time and the
on-time of the LT3580 switch.
Start-Up Operation
Several functions are provided to enable a very clean
start-up for the LT3580.
• First, the SHDN pin voltage is monitored by an internal
voltage reference to give a precise turn-on voltage level.
An external resistor (or resistor divider) can be connected
from the input power supply to the SHDN pin to provide
a user-programmable undervoltage lockout function.
VIN > VOUT
OR
VIN = VOUT
OR
VIN < VOUT
L1
C2
•
VIN
SW
RT
L1
VOUT
RT
VIN
R1
FB
SS
SW
SHDN
SHUTDOWN
RT
RT
3580 F01
Figure 1. SEPIC Topology Allows for the Input to Span
the Output Voltage. Coupled or Uncoupled Inductors
Can Be Used. Follow Noted Phasing if Coupled
VOUT
R1
GND
VC
SYNC
CC
L2
D1
FB
C3
RC
CSS
•
LT3580
+
GND
C2
•
VIN
+
VC
SYNC
The LT3580 has a current limit circuit not shown in the
Block Diagram. The switch current is consistently monitored and not allowed to exceed the maximum switch
current at a given duty cycle (see the Electrical Characteristics table). If the switch current reaches this value,
the SR latch (SR1) is reset regardless of the state of the
comparator (A1/A2). Also not shown in the Block Diagram
is the thermal shutdown circuit. If the temperature of the
part exceeds approximately 165°C, the SR2 latch is set
regardless of the state of the comparator (A1/A2). A full
soft-start cycle will then be initiated. The current limit and
thermal shutdown circuits protect the power switch as well
as the external components connected to the LT3580.
C1
SHDN
SHUTDOWN
Current Limit and Thermal Shutdown Operation
L2
LT3580
C1
• Finally, the frequency foldback circuit reduces the
switching frequency when the FB pin is in a nominal range
of 350mV to 900mV. This feature reduces the minimum
duty cycle that the part can achieve thus allowing better
control of the switch current during start-up. When the
FB voltage is pulled outside of this range, the switching
frequency returns to normal.
D1
•
+
• Second, the soft-start circuitry provides for a gradual
ramp-up of the switch current. When the part is brought
out of shutdown, the external SS capacitor is first
discharged (providing protection against SHDN pin
glitches and slow ramping), then an integrated 275k
resistor pulls the SS pin up to ~2.2V. By connecting an
external capacitor to the SS pin, the voltage ramp rate
on the pin can be set. Typical values for the soft-start
capacitor range from 100nF to 1μF.
SS
+
C3
RC
CSS
CC
3580 F02
Figure 2. Dual Inductor Inverting Topology Results in
Low Output Ripple. Coupled or Uncoupled Inductors
Can Be Used. Follow Noted Phasing if Coupled
3580fg
7
LT3580
APPLICATIONS INFORMATION
Setting Output Voltage
Inductor Selection
The output voltage is set by connecting a resistor (RFB)
from VOUT to the FB pin. RFB is determined from the
following equation:
|V − V |
RFB = OUT FB
83.3µA
General Guidelines: The high frequency operation of the
LT3580 allows for the use of small surface mount inductors.
For high efficiency, choose inductors with high frequency
core material, such as ferrite, to reduce core losses. To
improve efficiency, choose inductors with more volume
for a given inductance. The inductor should have low
DCR (copper wire resistance) to reduce I2R losses, and
must be able to handle the peak inductor current without
saturating. Note that in some applications, the current
handling requirements of the inductor can be lower, such
as in the SEPIC topology, where each inductor only carries
a fraction of the total switch current. Molded chokes or chip
inductors usually do not have enough core area to support peak inductor currents in the 2A to 3A range. To
minimize radiated noise, use a toroidal or shielded inductor.
Note that the inductance of shielded types will drop more
as current increases, and will saturate more easily. See
Table 1 for a list of inductor manufacturers. Thorough lab
evaluation is recommended to verify that the following
guidelines properly suit the final application.
where VFB is 1.215V (typical) for non-inverting topologies
(i.e., boost and SEPIC regulators) and 5mV (typical) for
inverting topologies (see the Electrical Characteristics).
Power Switch Duty Cycle
In order to maintain loop stability and deliver adequate
current to the load, the power NPN (Q1 in the Block Diagram) cannot remain “on” for 100% of each clock cycle.
The maximum allowable duty cycle is given by:
DCMAX =
(TP − Min Off Time)
• 100%
TP
where TP is the clock period and Min Off Time (found in
the Electrical Characteristics) is typically 60ns.
The application should be designed so that the operating
duty cycle does not exceed DCMAX.
Duty cycle equations for several common topologies are
given below, where VD is the diode forward voltage drop
and VCESAT is typically 300mV at 1.5A.
For the boost topology:
V −V +V
DC ≅ OUT IN D
VOUT + VD − VCESAT
For the SEPIC or dual inductor inverting topology (see
Figures 1 and 2):
VD +| VOUT |
DC ≅
VIN + | VOUT | + VD − VCESAT
The LT3580 can be used in configurations where the duty
cycle is higher than DCMAX, but it must be operated in the
discontinuous conduction mode so that the effective duty
cycle is reduced.
Table 1.Inductor Manufacturers
Coilcraft
DO3316P, MSS7341 and LPS4018
Series
www.coilcraft.com
Coiltronics DR, LD and CD Series
www.coiltronics.com
Murata
LQH55D and LQH66S Series
www.murata.com
Sumida
CDRH5D18B/HP, CDR6D23MN,
www.sumida.com
CDRH6D26/HP, CDRH6D28,
CDR7D28MN and CDRH105R Series
TDK
RLF7030 and VLCF4020 Series
www.tdk.com
Würth
WE-PD and WE-PD2 Series
www.we-online.com
Minimum Inductance : Although there can be a tradeoff with
efficiency, it is often desirable to minimize board space by
choosing smaller inductors. When choosing an inductor,
there are two conditions that limit the minimum inductance;
(1) providing adequate load current, and (2) avoidance of
subharmonic oscillation. Choose an inductance that is high
enough to meet both of these requirements.
Adequate Load Current : Small value inductors result in
increased ripple currents and thus, due to the limited peak
switch current, decrease the average current that can be
3580fg
8
LT3580
APPLICATIONS INFORMATION
provided to a load (IOUT). In order to provide adequate
load current, L should be at least:
L>
DC • VIN
⎛
|V |• I ⎞
2(f) ⎜ ILIM − OUT OUT ⎟
VIN • η ⎠
⎝
for boost, topologies, or:
L>
⎛
2(f) ⎜⎜ILIM −
⎝
DC • VIN
VOUT • IOUT
VIN • η
⎞
− IOUT ⎟⎟
⎠
for the SEPIC and inverting topologies.
where:
L = L1||L2 for uncoupled dual inductor topologies
DC = switch duty cycle (see previous section)
ILIM = switch current limit, typically about 2.4A at 50%
duty cycle (see the Typical Performance Characteristics
section).
η = power conversion efficiency (typically 88% for
boost and 75% for dual inductor topologies at high
currents).
f = switching frequency
Negative values of L indicate that the output load current
IOUT exceeds the switch current limit capability of the
LT3580.
for the uncoupled inductor SEPIC and uncoupled inductor
inverting topologies.
Maximum Inductance: Excessive inductance can reduce
current ripple to levels that are difficult for the current comparator (A3 in the Block Diagram) to cleanly discriminate,
thus causing duty cycle jitter and/or poor regulation. The
maximum inductance can be calculated by:
LMAX =
VIN – VCESAT DC
•
IMIN−RIPPLE
f
where LMAX is L1||L2 for uncoupled dual inductor topologies and IMIN-RIPPLE is typically 95mA.
Current Rating: Finally, the inductor(s) must have a rating
greater than its peak operating current to prevent inductor
saturation resulting in efficiency loss. In steady state, the
peak input inductor current (continuous conduction mode
only) is given by:
IL1−PEAK =
VOUT •IOUT
VIN • η
+
VIN • DC
2 • L1• f
for the boost, uncoupled inductor SEPIC and uncoupled
inductor inverting topologies.
For uncoupled dual inductor topologies, the peak output
inductor current is given by:
IL2−PEAK =IOUT +
VOUT • (1– DC)
2 • L2 • f
Avoiding Subharmonic Oscillations: The LT3580’s internal
slope compensation circuit will prevent subharmonic oscillations that can occur when the duty cycle is greater than
50%, provided that the inductance exceeds a minimum
value. In applications that operate with duty cycles greater
than 50%, the inductance must be at least:
V • (2 • DC – 1)
L > IN
(1−DC) • (f)
For the coupled inductor topologies:
for boost, coupled inductor SEPIC, and coupled inductor
inverting topologies, or:
Low ESR (equivalent series resistance) capacitors should
be used at the output to minimize the output ripple voltage.
Multilayer ceramic capacitors are an excellent choice, as
they have an extremely low ESR and are available in very
small packages. X5R or X7R dielectrics are preferred, as
L1 L2 >
VIN • (2 • DC – 1)
(1−DC) • (f)
⎡
⎤ V • DC
V
IOUT ⎢1+ OUT ⎥ + IN
⎣ η• VIN ⎦ 2 • L • f
Note: Inductor current can be higher during load transients.
It can also be higher during start-up if inadequate soft-start
capacitance is used.
Capacitor Selection
3580fg
9
LT3580
APPLICATIONS INFORMATION
these materials retain their capacitance over wider voltage
and temperature ranges. A 4.7μF to 20μF output capacitor is sufficient for most applications, but systems with
very low output currents may need only a 1μF or 2.2μF
output capacitor. Always use a capacitor with a sufficient
voltage rating. Many capacitors rated at 2.2μF to 20μF,
particularly 0805 or 0603 case sizes, have greatly reduced
capacitance at the desired output voltage. Solid tantalum
or OS-CON capacitors can be used, but they will occupy
more board area than a ceramic and will have a higher
ESR with greater output ripple.
Ceramic capacitors also make a good choice for the input
decoupling capacitor, which should be placed as closely as
possible to the LT3580. A 2.2μF to 4.7μF input capacitor
is sufficient for most applications.
Table 2 shows a list of several ceramic capacitor manufacturers. Consult the manufacturers for detailed information
on their entire selection of ceramic parts.
Table 2. Ceramic Capacitor Manufacturers
Kemet
www.kemet.com
Murata
www.murata.com
Taiyo Yuden
www.t-yuden.com
Compensation—Adjustment
To compensate the feedback loop of the LT3580, a series
resistor-capacitor network in parallel with a single capacitor
should be connected from the VC pin to GND. For most
applications, the series capacitor should be in the range
of 470pF to 2.2nF with 1nF being a good starting value.
The parallel capacitor should range in value from 10pF to
100pF with 47pF a good starting value. The compensation
resistor, RC , is usually in the range of 5k to 50k. A good
technique to compensate a new application is to use a
100kΩ potentiometer in place of series resistor RC. With
the series capacitor and parallel capacitor at 1nF and 47pF
respectively, adjust the potentiometer while observing the
transient response and the optimum value for RC can be
found. Figures 3a to 3c illustrate this process for the circuit
of Figure 14 with a load current stepped between 400mA
and 500mA. Figure 3a shows the transient response with
RC equal to 1k. The phase margin is poor, as evidenced by
the excessive ringing in the output voltage and inductor
current. In Figure 3b, the value of RC is increased to 3k,
which results in a more damped response. Figure 3c
shows the results when RC is increased further to 10k. The
transient response is nicely damped and the compensation
procedure is complete.
VOUT
200mV/DIV
AC COUPLED
VOUT
200mV/DIV
AC COUPLED
IL
0.5A/DIV
IL
0.5A/DIV
RC = 1k
3580 F03a
200μs/DIV
RC = 3k
Figure 3a. Transient Response Shows Excessive Ringing
200μs/DIV
3580 F03b
Figure 3b. Transient Response Is Better
VOUT
200mV/DIV
AC COUPLED
IL
0.5A/DIV
RC = 10k
200μs/DIV
3580 F03c
Figure 3c. Transient Response Is Well Damped
3580fg
10
LT3580
APPLICATIONS INFORMATION
Compensation—Theory
Like all other current mode switching regulators, the
LT3580 needs to be compensated for stable and efficient
operation. Two feedback loops are used in the LT3580—
a fast current loop which does not require compensation,
and a slower voltage loop which does. Standard bode plot
analysis can be used to understand and adjust the voltage
feedback loop.
As with any feedback loop, identifying the gain and phase
contribution of the various elements in the loop is critical.
Figure 4 shows the key equivalent elements of a boost
converter. Because of the fast current control loop, the
power stage of the IC, inductor and diode have been replaced
by a combination of the equivalent transconductance
amplifier gmp and the current controlled current source
(which converts IVIN to ηVIN/VOUT • IVIN). gmp acts as
a current source where the peak input current, IVIN, is
proportional to the VC voltage. η is the efficiency of the
switching regulator, and is typically about 88%.
Note that the maximum output currents of gmp and gma are
finite. The limits for gmp are in the Electrical Characteristics
section (switch current limit), and gma is nominally limited
to about ±12μA.
–
+
H • VIN
•IVIN
VOUT
RESR
COUT
Output Pole: P1=
2
2 • π • RL • COUT
Error Amp Pole: P2 =
1
2 • π • ⎡⎣RO + RC ⎤⎦ • CC
Error Amp Zero: Z1=
1
2 • π • RC • CC
DC Gain:
(Breaking Loop at FB Pin)
ADC = A OL (0) =
∂VC ∂IVIN ∂VOUT ∂VFB
•
•
•
=
∂VFB ∂VC ∂IVIN ∂VOUT
⎛
(gma • R0 ) • gmp • ⎜ η • VVIN
⎝
ESR Zero: Z2 =
RHP Zero: Z3 =
RL
VC
CF
RC
CC
RO
R1
+
gma
R2
–
RL ⎞
0.5R2
•
⎟
2 ⎠ R1+ 0.5R2
1
2 • π • RESR • COUT
VIN 2 • RL
2 • π • VOUT 2 • L
Phase Lead Zero: Z4 =
CPL
1.215V
REFERENCE
•
OUT
High Frequency Pole: P3 >
VOUT
IVIN
gmp
From Figure 4, the DC gain, poles and zeros can be calculated as follows:
Phase Lead Pole: P4 =
fS
3
1
2 • π • R1• CPL
1
R2
2 •C
2•π•
R2 PL
R1+
2
R1•
FB
3580 F04
R2
CC: COMPENSATION CAPACITOR
COUT: OUTPUT CAPACITOR
CPL: PHASE LEAD CAPACITOR
CF: HIGH FREQUENCY FILTER CAPACITOR
gma: TRANSCONDUCTANCE AMPLIFIER INSIDE IC
gmp: POWER STAGE TRANSCONDUCTANCE AMPLIFIER
RC: COMPENSATION RESISTOR
RL: OUTPUT RESISTANCE DEFINED AS VOUT DIVIDED BY ILOAD(MAX)
RO: OUTPUT RESISTANCE OF gma
R1, R2: FEEDBACK RESISTOR DIVIDER NETWORK
RESR: OUTPUT CAPACITOR ESR
Figure 4. Boost Converter Equivalent Model
Error Amp Filter Pole:
P5 =
C
1
,CF < C
R •R
10
2 • π • C O • CF
RC +RO
The current mode zero (Z3) is a right-half plane zero
which can be an issue in feedback control design, but is
manageable with proper external component selection.
3580fg
11
LT3580
APPLICATIONS INFORMATION
Using the circuit in Figure 14 as an example, Table 3 shows
the parameters used to generate the bode plot shown in
Figure 5.
Table 3. Bode Plot Parameters
PARAMETER
VALUE
UNITS
COMMENT
21.8
Ω
Application Specific
COUT
10
μF
Application Specific
RESR
10
mΩ
Application Specific
RO
305
kΩ
Not Adjustable
CC
1000
pF
Adjustable
CF
0
pF
Optional/Adjustable
CPL
0
pF
Optional/Adjustable
RC
10
kΩ
Adjustable
R1
130
kΩ
Adjustable
R2
14.6
kΩ
Not Adjustable
VOUT
12
V
Application Specific
VIN
5
V
Application Specific
gma
230
μmho
Not Adjustable
gmp
7
mho
Not Adjustable
L
4.2
μH
Application Specific
fS
1.2
MHz
Adjustable
RL
In Figure 5, the phase is –140° when the gain reaches 0dB
giving a phase margin of 40°. The crossover frequency
is 10kHz, which is more than three times lower than the
frequency of the RHP zero to achieve adequate phase
margin.
180
0
160
–20
140
–40
–60
PHASE
–80
100
–100
80
40o AT
10kHz
60
40
–120
–140
GAIN
20
PHASE (DEG)
GAIN (dB)
120
–160
–180
0
Diode Selection
Schottky diodes, with their low forward voltage drops and
fast switching speeds, are recommended for use with the
LT3580. The Microsemi UPS120 is a very good choice.
Where the input-to-output voltage differential exceeds 20V,
use the UPS140 (a 40V diode). These diodes are rated to
handle an average forward current of 1A.
Oscillator
The operating frequency of the LT3580 can be set by the
internal free-running oscillator. When the SYNC pin is
driven low (< 0.4V), the frequency of operation is set by
a resistor from RT to ground. An internally trimmed timing
capacitor resides inside the IC. The oscillator frequency is
calculated using the following formula:
fOSC =
91.9
(R T + 1)
where fOSC is in MHz and RT is in kΩ. Conversely, RT
(in kΩ) can be calculated from the desired frequency
(in MHz) using:
RT =
91.9
−1
fOSC
Clock Synchronization
The operating frequency of the LT3580 can be synchronized
to an external clock source. To synchronize to the external
source, simply provide a digital clock signal into the SYNC
pin. The LT3580 will operate at the SYNC clock frequency.
The LT3580 will revert to the internal free-running oscillator
clock after SYNC is driven low for a few free-running clock
periods.
Driving SYNC high for an extended period of time effectively
stops the operating clock and prevents latch SR1 from
becoming set (see the Block Diagram). As a result, the
switching operation of the LT3580 will stop.
–200
–20
10
100
1k
10k
FREQUENCY (Hz)
100k
1M
3580 F05
Figure 5. Bode Plot for Example Boost Converter
The duty cycle of the SYNC signal must be between 35%
and 65% for proper operation. Also, the frequency of the
SYNC signal must meet the following two criteria:
3580fg
12
LT3580
APPLICATIONS INFORMATION
(2) The SYNC frequency can always be higher than the
free-running oscillator frequency, fOSC , but should not
be less than 25% below fOSC .
Operating Frequency Selection
There are several considerations in selecting the operating
frequency of the converter. The first is staying clear of
sensitive frequency bands, which cannot tolerate any
spectral noise. For example, in products incorporating RF
communications, the 455kHz IF frequency is sensitive to
any noise, therefore switching above 600kHz is desired.
Some communications have sensitivity to 1.1MHz, and in
that case, a 1.5MHz switching converter frequency may be
employed. The second consideration is the physical size
of the converter. As the operating frequency goes up, the
inductor and filter capacitors go down in value and size.
The tradeoff is efficiency, since the switching losses due
to NPN base charge (see Thermal Calculations), Schottky
diode charge, and other capacitive loss terms increase
proportionally with frequency.
Soft-Start
The LT3580 contains a soft-start circuit to limit peak switch
currents during start-up. High start-up current is inherent
in switching regulators in general since the feedback loop
is saturated due to VOUT being far from its final value. The
regulator tries to charge the output capacitor as quickly as
possible, which results in large peak currents.
The start-up current can be limited by connecting an
external capacitor (typically 100nF to 1μF) to the SS pin.
This capacitor is slowly charged to ~2.2V by an internal
275k resistor once the part is activated. SS pin voltages
below ~1.1V reduce the internal current limit. Thus, the
gradual ramping of the SS voltage also gradually increases
the current limit as the capacitor charges. This, in turn,
allows the output capacitor to charge gradually toward its
final value while limiting the start-up current.
In the event of a commanded shutdown or lockout (SHDN
pin), internal undervoltage lockout (UVLO) or a thermal
lockout, the soft-start capacitor is automatically discharged
to ~200mV before charging resumes, thus assuring that
the soft-start occurs after every reactivation of the chip.
Shutdown
The SHDN pin is used to enable or disable the chip.
For most applications, SHDN can be driven by a digital
logic source. Voltages above 1.38V enable normal active
operation. Voltages below 300mV will shutdown the chip,
resulting in extremely low quiescent current.
While the SHDN voltage transitions through the lockout
voltage range (0.3V to 1.24V) the power switch is disabled
and the SR2 latch is set (see the Block Diagram). This
causes the soft-start capacitor to begin discharging,
which continues until the capacitor is discharged and
active operation is enabled. Although the power switch
is disabled, SHDN voltages in the lockout range do not
necessarily reduce quiescent current until the SHDN voltage
is near or below the shutdown threshold.
Also note that SHDN can be driven above VIN or VOUT as
long as the SHDN voltage is limited to less than 32V.
ACTIVE
(NORMAL OPERATION)
1.38V
1.24V
SHDN (V)
(1) SYNC may not toggle outside the frequency range of
200kHz to 2.5MHz unless it is stopped low to enable
the free-running oscillator.
0.3V
0.0V
(HYSTERESIS AND TOLERANCE)
LOCKOUT
(POWER SWITCH OFF,
SS CAPACITOR DISCHARGED)
SHUTDOWN
(LOW QUIESCENT CURRENT)
3580 F06
Figure 6. Chip States vs SHDN Voltage
Configurable Undervoltage Lockout
Figure 7 shows how to configure an undervoltage lockout
(UVLO) for the LT3580. Typically, UVLO is used in situations
where the input supply is current-limited, has a relatively
high source resistance, or ramps up/down slowly. A
switching regulator draws constant power from the source,
so source current increases as source voltage drops. This
looks like a negative resistance load to the source and can
cause the source to current-limit or latch low under low
3580fg
13
LT3580
APPLICATIONS INFORMATION
VIN
VIN
1.3V
RUVLO1
SHDN
–
ACTIVE/
LOCKOUT
+
RUVLO1 =
11.6μA
AT 1.3V
RUVLO2
(OPTIONAL)
GND
3580 F07
Figure 7. Configurable UVLO
source voltage conditions. UVLO prevents the regulator
from operating at source voltages where these problems
might occur.
The shutdown pin comparator has voltage hysteresis with
typical thresholds of 1.32V (rising) and 1.29V (falling).
Resistor RUVLO2 is optional. RUVLO2 can be included
to reduce the overall UVLO voltage variation caused by
variations in SHDN pin current (see the Electrical Characteristics). A good choice for RUVLO2 is ≤10k ±1%. After
choosing a value for RUVLO2 , RUVLO1 can be determined
from either of the following:
VIN+ −1.32V
RUVLO1 =
⎛ 1.32V ⎞
⎜
⎟ +11.6μA
⎝ RUVLO2 ⎠
or
RUVLO1 =
−
VIN −1.29V
⎛ 1.29V ⎞
⎜
⎟ +11.6μA
⎝ RUVLO2 ⎠
where VIN+ and VIN– are the VIN voltages when rising or
falling respectively.
For example, to disable the LT3580 for VIN voltages below
3.5V using the single resistor configuration, choose:
RUVLO1 =
3.5V −1.29V
=190.5k
⎛ 1.29V ⎞
⎜
⎟ +11.6μA
⎝ ∞ ⎠
To activate the LT3580 for VIN voltage greater than
4.5V using the double resistor configuration, choose
RUVLO2 = 10k and:
4.5V −1.32V
= 22.1k
⎛ 1.32V ⎞
⎜
⎟ +11.6μA
⎝ 10k ⎠
Internal Undervoltage Lockout
The LT3580 monitors the VIN supply voltage in case VIN
drops below a minimum operating level (typically about
2.3V). When VIN is detected low, the power switch is
deactivated, and while sufficient VIN voltage persists, the
soft-start capacitor is discharged. After VIN is detected
high, the power switch will be reactivated and the soft-start
capacitor will begin charging.
Thermal Considerations
For the LT3580 to deliver its full output power, it is imperative
that a good thermal path be provided to dissipate the heat
generated within the package. This is accomplished by
taking advantage of the thermal pad on the underside of
the IC. It is recommended that multiple vias in the printed
circuit board be used to conduct heat away from the IC and
into a copper plane with as much area as possible.
Thermal Lockout
If the die temperature reaches approximately 165°C, the
part will go into thermal lockout, the power switch will be
turned off and the soft-start capacitor will be discharged.
The part will be enabled again when the die temperature
has dropped by ~5°C (nominal).
Thermal Calculations
Power dissipation in the LT3580 chip comes from four
primary sources: switch I2R loss, NPN base drive (AC), NPN
base drive (DC), and additional input current. The following
formulas can be used to approximate the power losses.
These formulas assume continuous mode operation,
3580fg
14
LT3580
APPLICATIONS INFORMATION
so they should not be used for calculating efficiency in
discontinuous mode or at light load currents.
•I
V
Average Input Current: IIN = OUT OUT
VIN • η
Switch I2R Loss: PSW = (DC)(IIN )2 (RSW )
Base Drive Loss (AC): PBAC =13n(IIN )(VOUT )(f)
Base Drive Loss (DC): PBDC =
(VIN )(IIN )(DC)
50
Input Power Loss: PINP = 7mA(VIN )
where:
RSW = switch resistance (typically 200mΩ at 1.5A)
DC = duty cycle (see the Power Switch Duty Cycle section for formulas)
η = power conversion efficiency (typically 88% at high
currents)
Example: boost configuration, VIN = 5V, VOUT = 12V,
IOUT = 0.5A, f = 1.25MHz, VD = 0.5V:
IIN = 1.36A
DC = 61.5%
PSW = 228mW
PBAC = 270mW
PBDC = 84mW
PINP = 35mW
Total LT3580 power dissipation (PTOT) = 617mW
Thermal resistance for the LT3580 is influenced by the presence of internal, topside or backside planes. To calculate
die temperature, use the appropriate thermal resistance
number and add in worst-case ambient temperature:
TJ = TA + θJA • PTOT
where TJ = junction temperature, TA = ambient temperature, θJA = 43°C/W for the 3mm × 3mm DFN package and
35°C/W to 40°C/W for the MSOP Exposed Pad package.
PTOT is calculated above.
VIN Ramp Rate
While initially powering a switching converter application,
the VIN ramp rate should be limited. High VIN ramp rates can
cause excessive inrush currents in the passive components
of the converter. This can lead to current and/or voltage
overstress and may damage the passive components or
the chip. Ramp rates less than 500mV/μs, depending on
component parameters, will generally prevent these issues.
Also, be careful to avoid hot-plugging. Hot-plugging occurs
when an active voltage supply is “instantly” connected or
switched to the input of the converter. Hot-plugging results
in very fast input ramp rates and is not recommended.
Finally, for more information, refer to Linear application
note AN88, which discusses voltage overstress that can
occur when an inductive source impedance is hot-plugged
to an input pin bypassed by ceramic capacitors.
Layout Hints
As with all high frequency switchers, when considering
layout, care must be taken to achieve optimal electrical,
thermal and noise performance. One will not get advertised performance with a careless layout. For maximum
efficiency, switch rise and fall times are typically in the
5ns to 10ns range. To prevent noise, both radiated and
conducted, the high speed switching current path, shown in
Figure 8, must be kept as short as possible. This is implemented in the suggested layout of a boost configuration in
Figure 9. Shortening this path will also reduce the parasitic
trace inductance. At switch-off, this parasitic inductance
produces a flyback spike across the LT3580 switch. When
operating at higher currents and output voltages, with poor
layout, this spike can generate voltages across the LT3580
that may exceed its absolute maximum rating. A ground
plane should also be used under the switcher circuitry to
prevent interplane coupling and overall noise.
The VC and FB components should be kept as far away
as practical from the switch node. The ground for these
components should be separated from the switch current path. Failure to do so can result in poor stability or
subharmonic oscillation.
3580fg
15
LT3580
APPLICATIONS INFORMATION
Board layout also has a significant effect on thermal resistance. The exposed package ground pad is the copper
plate that runs under the LT3580 die. This is a good thermal
path for heat out of the package. Soldering the pad onto
the board reduces die temperature and increases the power
capability of the LT3580. Provide as much copper area as
possible around this pad. Adding multiple feedthroughs
around the pad to the ground plane will also help. Figures
9 and 10 show the recommended component placement
for the boost and SEPIC configurations, respectively.
Layout Hints for Inverting Topology
Figure 11 shows recommended component placement for
the dual inductor inverting topology. Input bypass capacitor, C1, should be placed close to the LT3580, as shown.
The load should connect directly to the output capacitor,
C2, for best load regulation. You can tie the local ground
into the system ground plane at the C3 ground terminal.
The cut ground copper at D1’s cathode is essential to
obtain low noise. This important layout issue arises due
to the chopped nature of the currents flowing in Q1 and
D1. If they are both tied directly to the ground plane before
being combined, switching noise will be introduced into
the ground plane. It is almost impossible to get rid of this
noise, once present in the ground plane. The solution
is to tie D1’s cathode to the ground pin of the LT3580
before the combined currents are dumped in the ground
plane as drawn in Figure 2, Figure 12 and Figure 13. This
single layout technique can virtually eliminate high
frequency “spike” noise, so often present on switching
regulator outputs.
L1
D1
C1
VOUT
SW
LT3580
VIN
HIGH
FREQUENCY
SWITCHING
PATH
C2 LOAD
GND
3580 F08
Figure 8. High Speed “Chopped” Switching Path for Boost Topology
3580fg
16
LT3580
APPLICATIONS INFORMATION
GND
GND
1
2
C1
VIN
6
4
L1
VIN
7
3
2
C1
SYNC
8
9
L1
SHDN
5
SYNC
8
1
9
7
3
6
4
5
SHDN
SW
SW
C2
L2
D1
VIAS TO GROUND
PLANE REQUIRED
TO IMPROVE
THERMAL
PERFORMANCE
C2
D1
VIAS TO GROUND
PLANE REQUIRED
TO IMPROVE
THERMAL
PERFORMANCE
C3
3580 F09
VOUT
3580 F10
VOUT
Figure 9. Suggested Component Placement for Boost Topology
(Both DFN and MSOP Packages. Not to Scale). Pin 9 (Exposed
Pad) Must Be Soldered Directly to the Local Ground Plane for
Adequate Thermal Performance. Multiple Vias to Additional
Ground Planes Will Improve Thermal Performance
Figure 10. Suggested Component Placement for Sepic Topology
(Both DFN And MSOP Packages. Not to Scale). Pin 9 (Exposed
Pad) Must Be Soldered Directly to the Local Ground Plane for
Adequate Thermal Performance. Multiple Vias to Additional
Ground Planes Will Improve Thermal Performance
GND
1
2
C1
VIN
8
9
SYNC
7
3
6
4
5
SHDN
L1
SW
C2
L2
D1
VIAS TO GROUND
PLANE REQUIRED
TO IMPROVE
THERMAL
PERFORMANCE
C3
VOUT
3580 F11
Figure 11. Suggested Component Placement for Inverting Topology (Both DFN and MSOP Packages. Not to Scale).
Note Cut in Ground Copper at Diode’s Cathode. Pin 9 (Exposed Pad) Must be Soldered Directly to Local Ground
Plane for Adequate Thermal Performance. Multiple Vias to Additional Ground Planes Will Improve Thermal
Performance
3580fg
17
LT3580
APPLICATIONS INFORMATION
–(VIN + ⏐VOUT⏐)
VCESAT
L1
SW
C2
L2
SWX
VIN
–VOUT
D1
Q1
+
C1
C3
RLOAD
+
3580 F12
Figure 12. Switch-On Phase of an Inverting Converter. L1 and L2 Have Positive dI/dt
VIN + |VOUT|+ VD
L1
SW
VD
C2
L2
SWX
VIN
–VOUT
D1
Q1
+
C1
C3
RLOAD
+
3580 F13
Figure 13. Switch-Off Phase of an Inverting Converter. L1 and L2 Currents Have Negative dI/dt
L1
4.2μH
VIN
5V
VIN
C2
10μF
SW
SHDN
RT
D1
VOUT
12V
550mA
GND
130k
LT3580
FB
VC
SYNC
C1
2.2μF
75k
SS
10k
0.1μF
1nF
3580 F14
C1: 2.2μF, 25V, X5R, 1206
C2: 10μF, 25V, X5R, 1206
D1: MICROSEMI UPS120
L1: SUMIDA CDR6D23MN-4R2
Figure 14. 1.2MHz, 5V to 12V Boost Converter
3580fg
18
LT3580
TYPICAL APPLICATIONS
750kHz, 5V to 40V, 150mA Boost Converter
L1
47μH
VIN
5V
VIN
C2
2.2μF
SW
SHDN
RT
D1
VOUT
40V
150mA
GND
464k
LT3580
FB
VC
SYNC
C1
2.2μF
SS
121k
10k
0.1μF
47pF
4.7nF
3580 TA02
C1: 2.2μF, 25V, X5R, 1206
C2: 2.2μF, 50V, X5R, 1206
D1: MICROSEMI UPS140
L1: SUMIDA CDRH105R-470
Wide Input Range SEPIC Converter with 5V Output Switches at 2.5MHz
C3
1μF
L1
4.7μH
VIN
2.6V TO 12V
OPERATING
12V TO 32V
TRANSIENT
SHDN
RT
VOUT
5V, 600mA (VIN = 5V OR HIGHER)
500mA (VIN = 4V)
C2
400mA (VIN = 3V)
10μF
300mA (VIN = 2.6V)
L2
4.7μH
SW
VIN
D1
GND
46.4k
LT3580
FB
VC
SYNC
C1
2.2μF
SS
35.7k
10k
0.1μF
22pF
1nF
3580 TA03a
C1: 2.2μF, 35V, X5R, 1206
C2: 10μF, 10V, X5R, 1206
C3: 1μF, 50V, X5R, 0805
D1: MICROSEMI UPS140
L1, L2: TDK VLCF4020T-4R7N1R2
Transient Response with 400mA to 500mA Output Load Step
VOUT
100mV/DIV
AC COUPLED
IL1 +IL2
0.5A/DIV
VIN = 12V
100μs/DIV
3580 TA03b
3580fg
19
LT3580
TYPICAL APPLICATIONS
VFD (Vacuum Flourescent Display) Power Supply Switches at 2MHz to Avoid AM Band
Danger High Voltage! Operation by High Voltage Trained Personnel Only
D1
R2
10Ω
VIN
9V TO 16V
C7
1μF
L1
10μH
D2
D3
R1
10Ω
3.3V
C6
1μF
SW
VIN
D4
C4
1μF
VOUT1
64V
40mA
D5
SHDN
C3
1μF
LT3580
C1
4.7μF
C5
1μF
VOUT2
95V
80mA
GND
RT
383k
FB
VC
C2
4.7μF
SYNC
SS
45.3k
10k
0.1μF
47pF
2.2nF
3580 TA04
C1, C2: 4.7μF, 25V, X5R, 1206
C3-C7: 1μF, 50V, X5R, 0805
D1-D4: ON SEMICONDUCTOR MBR0540
D5: MICROSEMI UPS140
L1: SUMIDA CDR6D28MNNP-100
R1, R2: 0.5W
3580fg
20
LT3580
TYPICAL APPLICATIONS
High Voltage Positive Power Supply Uses Tiny 5.8mm × 5.8mm × 3mm Transformer and Switches at 200kHz
Danger High Voltage! Operation by High Voltage Trained Personnel Only
VOUT
350V
4.5mA (VIN = 5V)
2.5mA (VIN = 3.3V)
T1
1:10.4
VIN
3.3V TO 5V
7, 8
•
1
D1
4.7μH
•
5, 6
4
C2
68nF
D2
SW
VIN
SHDN
RT
FOR ANY VOUT BETWEEN 50V TO
350V, CHOOSE RFB ACCORDING TO
GND
RFB 4.22M*
LT3580
V
– 1.215
RFB = OUT
83.3μA
FB
VC
SYNC
C1
2.2μF
464k
SS
10k
0.47μF
100pF
10nF
3580 TA05a
C1: 2.2μF, 25V, X5R, 1206
C2: TDK C3225X7R2J683M
D1: VISHAY GSD2004S DUAL DIODE CONNECTED IN SERIES
D2: ON SEMICONDUCTOR MBR0540
T1: TDK LDT565630T-041
FOR 5V INPUT, KEEP MAXIMUM
OUTPUT POWER AT 1.58W
FOR 3.3V INPUT, KEEP MAXIMUM
OUTPUT POWER AT 0.88W
*MAY REQUIRE MULTIPLE SERIES
RESISTORS TO COMPLY WITH
MAXIMUM VOLTAGE RATINGS
Start-Up Waveforms
IPRIMARY
1A/DIV
VOUT
50V/DIV
5V INPUT
NO LOAD
2ms/DIV
3580 TA05b
Switching Waveforms
VOUT
2V/DIV
AC COUPLED
IPRIMARY
1A/DIV
5V INPUT
4.5mA LOAD
2μs/DIV
3580 TA05c
3580fg
21
LT3580
TYPICAL APPLICATIONS
High Voltage Negative Power Supply Uses Tiny 5.8mm × 5.8mm × 3mm Transformer and Switches at 200kHz
Danger High Voltage! Operation by High Voltage Trained Personnel Only
T1
1:10.4
VIN
3.3V TO 5V
7, 8
•
D1
1
4.7μH
•
5, 6
C2
68nF
4
FOR ANY VOUT BETWEEN –50V TO
–350V, CHOOSE RFB ACCORDING TO
D2
SHDN
RT
RFB =
SW
VIN
GND
RFB 4.22M*
LT3580
VOUT
–350V
4.5mA (VIN = 5V)
2.5mA (VIN = 3.3V)
FB
VC
SYNC
C1
2.2μF
464k
SS
10k
0.47μF
100pF
10nF
VOUT
83.3μA
FOR 5V INPUT, KEEP MAXIMUM
OUTPUT POWER AT 1.58W
FOR 3.3V INPUT, KEEP MAXIMUM
OUTPUT POWER AT 0.88W
*MAY REQUIRE MULTIPLE SERIES
RESISTORS TO COMPLY WITH
MAXIMUM VOLTAGE RATINGS
3580 TA06
C1: 2.2μF, 25V, X5R, 1206
C2: TDK C3225X7R2J683M
D1: VISHAY GSD2004S DUAL DIODE CONNECTED IN SERIES
D2: ON SEMICONDUCTOR MBR0540
T1: TDK LDT565630T-041
3580fg
22
LT3580
TYPICAL APPLICATIONS
5V to 12V Boost Converter Switches at 2.5MHz and Uses a Tiny 4mm × 4mm × 1.7mm Inductor
L1
3.3μH
VIN
5V
D1
VIN
SHDN
GND
130k
LT3580
RT
C2
4.7μF
SW
VOUT
12V
500mA
FB
VC
SYNC
C1
4.7μF
SS
35.7k
10k
0.1μF
47pF
2.2nF
3580 TA07a
C1, C2: 4.7μF, 25V, X5R, 1206
D1: MICROSEMI UPS120
L1: COILCRAFT LPS4018-332ML
Efficiency and Power Loss
vs Load Current
95
1400
90
1200
1000
80
75
800
70
600
65
400
POWER LOSS (W)
EFFICIENCY (%)
85
60
200
55
50
0
100
200
300
400
LOAD CURRENT (mA)
500
0
600
3580 TA07b
Transient Response with 400mA to
500mA to 400mA Output Load Step
Start-Up Waveforms
VOUT
5V/DIV
VOUT
0.5V/DIV
AC COUPLED
IL
1A/DIV
IL
0.5A/DIV
VSHDN
1V/DIV
100μs/DIV
3580 TA07c
500mA LOAD
2ms/DIV
3580 TA07d
3580fg
23
LT3580
TYPICAL APPLICATIONS
–5V Output Inverting Converter Switches at 2.5MHz and Accepts Inputs Between 3.3V to 12V
C3
1μF
L1
4.7μH
VIN
3.3V TO 12V
VIN
SW
SHDN
VOUT
–5V
800mA (VIN = 12V)
C2 620mA (VIN = 5V)
10μF 450mA (VIN = 3.3V)
D1
GND
60.4k
LT3580
RT
L2
4.7μH
FB
VC
SYNC
C1
2.2μF
35.7k
SS
10k 100pF
0.1μF
2.2nF
3580 TA08a
C1: 2.2μF, 25V, X5R, 1206
C2: 10μF, 25V, X5R, 1206
C3: 1μF, 50V, X5R, 0805
D1: CENTRAL SEMI CMMSH1-40
L1, L2: COILCRAFT LSP4018-472ML
Efficiency and Power Loss
vs Load Current
85
1200
VIN = 5V
80
1000
800
70
65
600
60
400
55
POWER LOSS (W)
EFFICIENCY (%)
75
50
200
45
40
0
100
200 300 400 500
LOAD CURRENT (mA)
600
0
700
3580 TA08b
3580fg
24
LT3580
PACKAGE DESCRIPTION
DD Package
8-Lead Plastic DFN (3mm × 3mm)
(Reference LTC DWG # 05-08-1698 Rev C)
0.70 p0.05
3.5 p0.05
1.65 p0.05
2.10 p0.05 (2 SIDES)
PACKAGE
OUTLINE
0.25 p 0.05
0.50
BSC
2.38 p0.05
RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS
APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED
3.00 p0.10
(4 SIDES)
R = 0.125
TYP
5
0.40 p 0.10
8
1.65 p 0.10
(2 SIDES)
PIN 1
TOP MARK
(NOTE 6)
(DD8) DFN 0509 REV C
0.200 REF
0.75 p0.05
4
0.25 p 0.05
1
0.50 BSC
2.38 p0.10
0.00 – 0.05
BOTTOM VIEW—EXPOSED PAD
NOTE:
1. DRAWING TO BE MADE A JEDEC PACKAGE OUTLINE M0-229 VARIATION OF (WEED-1)
2. DRAWING NOT TO SCALE
3. ALL DIMENSIONS ARE IN MILLIMETERS
4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE
MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE
5. EXPOSED PAD SHALL BE SOLDER PLATED
6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION
ON TOP AND BOTTOM OF PACKAGE
3580fg
25
LT3580
PACKAGE DESCRIPTION
MS8E Package
8-Lead Plastic MSOP, Exposed Die Pad
(Reference LTC DWG # 05-08-1662 Rev F)
BOTTOM VIEW OF
EXPOSED PAD OPTION
1.88
(.074)
1
0.889 p 0.127
(.035 p .005)
1.88 p 0.102
(.074 p .004)
0.29
REF
1.68
(.066)
0.05 REF
5.23
(.206)
MIN
DETAIL “B”
CORNER TAIL IS PART OF
DETAIL “B” THE LEADFRAME FEATURE.
FOR REFERENCE ONLY
NO MEASUREMENT PURPOSE
1.68 p 0.102 3.20 – 3.45
(.066 p .004) (.126 – .136)
8
0.42 p 0.038
(.0165 p .0015)
TYP
3.00 p 0.102
(.118 p .004)
(NOTE 3)
0.65
(.0256)
BSC
8
7 6 5
0.52
(.0205)
REF
RECOMMENDED SOLDER PAD LAYOUT
0.254
(.010)
3.00 p 0.102
(.118 p .004)
(NOTE 4)
4.90 p 0.152
(.193 p .006)
DETAIL “A”
0o – 6o TYP
GAUGE PLANE
1
0.53 p 0.152
(.021 p .006)
DETAIL “A”
2 3
4
1.10
(.043)
MAX
0.86
(.034)
REF
0.18
(.007)
SEATING
PLANE
0.22 – 0.38
(.009 – .015)
TYP
0.65
(.0256)
NOTE:
BSC
1. DIMENSIONS IN MILLIMETER/(INCH)
2. DRAWING NOT TO SCALE
3. DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS.
MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.152mm (.006") PER SIDE
4. DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS.
INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.152mm (.006") PER SIDE
5. LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING) SHALL BE 0.102mm (.004") MAX
6. EXPOSED PAD DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH ON E-PAD
SHALL NOT EXCEED 0.254mm (.010") PER SIDE.
0.1016 p 0.0508
(.004 p .002)
MSOP (MS8E) 0210 REV F
3580fg
26
LT3580
REVISION HISTORY
(Revision history begins at Rev F)
REV
DATE
DESCRIPTION
PAGE NUMBER
F
06/10
Added GND to the Pin Configuration section.
2
Revised Note 2 in the Electrical Characteristics section.
3
Revised Graph G08 in the Typical Performance Characteristics section.
Revised the Applications Information section.
G
09/10
4
10-11
Revised Table 3 in the Applications Information section.
12
Revised Figure 13 in the Applications Information section.
18
Updated drawing TA01a in the Typical Applications section.
24
Updated Related Parts table.
28
Added H- and MP-Grade information to Absolute Maximum Ratings, Order Information, Electrical Characteristics and
Pin Functions sections.
Added text at end of General Guidelines and revised equations under Avoiding Subharmonic Oscillations in
Applications Information section.
2, 3, 5
8, 9
3580fg
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
27
LT3580
TYPICAL APPLICATION
2MHz Inverting Converter Generates –12V from a 5V to 12V Input
VIN
5V TO 12V
SHDN
RT
C2
10μF
D1
SW
VOUT
–12V
500mA (VIN = 12V)
350mA (VIN = 5V)
GND
147k
LT3580
FB
VC
SYNC
C1
2.2μF
SS
45.3k
10k
0.1μF
47pF
1400
VIN = 5V
85
1200
80
1000
75
800
70
600
65
400
60
2.2nF
POWER LOSS (mw)
VIN
90
L2
22μH
EFFICIENCY (%)
C3
1μF
L1
10μH
Efficiency and Power Loss
vs Load Current
200
55
3580 TA09a
C1: 2.2μF, 25V, X5R, 1206
C2: 10μF, 25V, X5R, 1206
C3: 1μF, 50V, X5R, 0805
D1: CENTRAL SEMI CMMSH1-40
L1: SUMIDA CDRH6D28NP-100NC
L2: SUMIDA CDRH3D28NP-220NC
50
0
50
0
100 150 200 250 300 350 400
LOAD CURRENT (mA)
3580 TA09b
RELATED PARTS
PART NUMBER
DESCRIPTION
COMMENTS
LT1310
2A (ISW), 40V, 1.2MHz High Efficiency Step-Up DC/DC Converter VIN: 2.3V to 16V, VOUT(MAX) = 40V, IQ = 3mA, ISD < 1μA, ThinSOT™
Package
LT1613
550mA (ISW), 1.4MHz High Efficiency Step-Up DC/DC Converter
VIN: 0.9V to 10V, VOUT(MAX) = 34V, IQ = 3mA, ISD < 1μA,
ThinSOT Package
LT1618
1.5A (ISW), 1.25MHz High Efficiency Step-Up DC/DC Converter
VIN: 1.6V to 18V, VOUT(MAX) = 35V, IQ = 1.8mA, ISD < 1μA,
MS10 Package
LT1930/LT1930A
1A (ISW), 1.2MHz/2.2MHz High Efficiency Step-Up DC/DC
Converter
VIN: 2.6V to 16V, VOUT(MAX) = 34V, IQ = 4.2mA/5.5mA, ISD < 1μA,
ThinSOT Package
LT1931/LT1931A
1A (ISW), 1.2MHz/2.2MHz High Efficiency Inverting DC/DC
Converter
VIN: 2.6V to 16V, VOUT(MAX) = 34V, IQ = 4.2mA/5.5mA, ISD < 1μA,
ThinSOT Package
LT1935
2A (ISW), 40V, 1.2MHz High Efficiency Step-Up DC/DC Converter VIN: 2.3V to 16V, VOUT(MAX) = 40V, IQ = 3mA, ISD < 1μA,
ThinSOT Package
LT1944/LT1944-1
(Dual)
Dual Output 350mA (ISW), Constant Off-Time, High Efficiency
Step-Up DC/DC Converter
VIN: 1.2V to 15V, VOUT(MAX) = 34V, IQ = 20μA, ISD < 1μA,
MS10 Package
LT1945 (Dual)
Dual Output Pos/Neg 350mA (ISW), Constant Off-Time,
High Efficiency Step-Up DC/DC Converter
VIN: 1.2V to 15V, VOUT(MAX) = ±34V, IQ = 20μA, ISD < 1μA,
MS10 Package
LT1946/LT1946A
1.5A (ISW), 1.2MHz/2.7MHz High Efficiency Step-Up DC/DC
Converter
VIN: 2.6V to 16V, VOUT(MAX) = 34V, IQ = 3.2mA, ISD < 1μA,
MS8E Package
LT1961
1.5A (ISW), 1.25MHz High Efficiency Step-Up DC/DC Converter
VIN: 3V to 25V, VOUT(MAX) = 35V, IQ = 0.9mA, ISD < 6μA,
MS8E Package
LT3436
3A (ISW), 800kHz, 34V Step-Up DC/DC Converter
VIN: 3V to 25V, VOUT(MAX) = 34V, IQ = 0.9mA, ISD < 6μA,
TSSOP16E Package
LT3467
1.1A (ISW), 1.3MHz High Efficiency Step-Up DC/DC Converter
VIN: 2.6V to 16V, VOUT(MAX) = 40V, IQ = 1.2mA, ISD < 1μA,
ThinSOT, 2mm × 3mm DFN Packages
LT3477
42V, 3A, 3.5MHz Boost, Buck-Boost, Buck LED Driver
VIN: 2.5V to 25V, VOUT(MAX) = 40V, Analog/PWM, ISD < 1μA,
QFN, TSSOP20E Packages
LT3479
3A Full-Featured DC/DC Converter with Soft-Start and Inrush
Current Protection
VIN: 2.5V to 24V, VOUT(MAX) = 40V, Analog/PWM, ISD < 1μA,
DFN, TSSOP Packages
3580fg
28 Linear Technology Corporation
LT 0910 REV G • PRINTED IN USA
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900 ● FAX: (408) 434-0507
●
www.linear.com
© LINEAR TECHNOLOGY CORPORATION 2007