MBRF2060CT D

MBRF2060CT
SWITCHMODEt
Schottky Power Rectifier
The SWITCHMODE Power Rectifier employs the Schottky Barrier
principle in a large area metal−to−silicon power diode.
State−of−the−art geometry features epitaxial construction with oxide
passivation and metal overlay contact. Ideally suited for use as
rectifiers in very low−voltage, high−frequency switching power
supplies, free wheeling diodes and polarity protection diodes.
Features
•
•
•
•
•
•
•
•
•
•
Highly Stable Oxide Passivated Junction
Very Low Forward Voltage Drop
Matched Dual Die Construction
High Junction Temperature Capability
High dv/dt Capability
Excellent Ability to Withstand Reverse Avalanche Energy Transients
Guardring for Stress Protection
Epoxy Meets UL 94 V−0 @ 0.125 in
Electrically Isolated. No Isolation Hardware Required.
Pb−Free Package is Available*
Mechanical Characteristics:
• Case: Epoxy, Molded
• Weight: 1.9 Grams (Approximately)
• Finish: All External Surfaces Corrosion Resistant and Terminal
http://onsemi.com
SCHOTTKY BARRIER
RECTIFIER
20 AMPERES, 60 VOLTS
1
2
3
ISOLATED TO−220
CASE 221D
STYLE 3
1
2
3
MARKING DIAGRAM
Leads are Readily Solderable
• Lead Temperature for Soldering Purposes:
260°C Max. for 10 Seconds
AYWW
B2060G
AKA
A
Y
WW
B2060
G
AKA
= Assembly Location
= Year
= Work Week
= Device Code
= Pb−Free Package
= Polarity Designator
ORDERING INFORMATION
Device
*For additional information on our Pb−Free strategy and soldering details, please
download the ON Semiconductor Soldering and Mounting Techniques
Reference Manual, SOLDERRM/D.
© Semiconductor Components Industries, LLC, 2009
December, 2009 − Rev. 8
1
Package
Shipping
MBRF2060CT
TO−220FP
50 Units/Rail
MBRF2060CTG
TO−220FP
(Pb−Free)
50 Units/Rail
Publication Order Number:
MBRF2060CT/D
MBRF2060CT
MAXIMUM RATINGS (Per Leg)
Rating
Symbol
Value
Unit
VRRM
VRWM
VR
60
V
IF(AV)
10
20
A
Peak Repetitive Forward Current
(Rated VR, Square Wave, 20 kHz), TC = 133°C
IFRM
20
A
Nonrepetitive Peak Surge Current
(Surge applied at rated load conditions halfwave, single phase, 60 Hz)
IFSM
150
A
Peak Repetitive Reverse Surge Current (2.0 ms, 1.0 kHz)
IRRM
0.5
A
TJ, Tstg
− 65 to +175
°C
dv/dt
10000
V/ms
Viso1
4500
V
Peak Repetitive Reverse Voltage
Working Peak Reverse Voltage
DC Blocking Voltage
Average Rectified Forward Current
(Rated VR), TC = 133°C
Total Device
Operating Junction and Storage Temperature Range (Note 1)
Voltage Rate of Change (Rated VR)
RMS Isolation Voltage (t = 0.3 second, R.H. ≤ 30%, TA = 25°C) (Note 2)
Per Figure 3
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
THERMAL CHARACTERISTICS (Per Leg)
Rating
Maximum Thermal Resistance, Junction−to−Case
Lead Temperature for Soldering Purposes: 1/8 in from Case for 5 Seconds
Symbol
Value
Unit
RqJC
4.0
°C/W
TL
260
°C
Symbol
Max
Unit
ELECTRICAL CHARACTERISTICS (Per Leg)
Characteristic
Maximum Instantaneous Forward Voltage (Note 3)
(iF = 10 Amp, TC = 25°C)
(iF = 10 Amp, TC = 125°C)
(iF = 20 Amp, TC = 25°C)
(iF = 20 Amp, TC = 125°C)
vF
Maximum Instantaneous Reverse Current (Note 3)
(Rated DC Voltage, TC = 25°C)
(Rated DC Voltage, TC = 125°C)
iR
V
0.85
0.75
0.95
0.85
mA
0.15
150
50
TJ = 150°C
150°C
20
I R, REVERSE CURRENT (mA)
i F, INSTANTANEOUS FORWARD CURRENT (AMPS)
1. The heat generated must be less than the thermal conductivity from Junction−to−Ambient: dPD/dTJ < 1/RqJA.
2. Proper strike and creepage distance must be provided.
3. Pulse Test: Pulse Width = 300 ms, Duty Cycle ≤ 2.0%
100°C
10
5.0
TJ = 25°C
3.0
1.0
10
TJ = 125°C
TJ = 100°C
1.0
0.1
0.01
0.5
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
vF, INSTANTANEOUS VOLTAGE (VOLTS)
0.9
1.0
TJ = 25°C
0
Figure 1. Typical Forward Voltage Per Diode
20
40
60
80
100
VR, REVERSE VOLTAGE (VOLTS)
120
Figure 2. Typical Reverse Current Per Diode
http://onsemi.com
2
MBRF2060CT
TEST CONDITION FOR ISOLATION TEST*
FULLY ISOLATED PACKAGE
LEADS
HEATSINK
0.110, MIN
Figure 3. Mounting Position
*Measurement made between leads and heatsink with all leads shorted together.
MOUNTING INFORMATION
CLIP
HEATSIN
K
Clip−Mounted
Figure 4. Typical Mounting Technique
http://onsemi.com
3
MBRF2060CT
PACKAGE DIMENSIONS
TO−220 FULLPAK
CASE 221D−03
ISSUE K
−T−
−B−
F
SEATING
PLANE
C
S
Q
U
A
1 2 3
H
−Y−
K
G
N
L
D
J
R
3 PL
0.25 (0.010)
M
B
M
Y
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH
3. 221D-01 THRU 221D-02 OBSOLETE, NEW
STANDARD 221D-03.
DIM
A
B
C
D
F
G
H
J
K
L
N
Q
R
S
U
INCHES
MIN
MAX
0.617
0.635
0.392
0.419
0.177
0.193
0.024
0.039
0.116
0.129
0.100 BSC
0.118
0.135
0.018
0.025
0.503
0.541
0.048
0.058
0.200 BSC
0.122
0.138
0.099
0.117
0.092
0.113
0.239
0.271
MILLIMETERS
MIN
MAX
15.67
16.12
9.96
10.63
4.50
4.90
0.60
1.00
2.95
3.28
2.54 BSC
3.00
3.43
0.45
0.63
12.78
13.73
1.23
1.47
5.08 BSC
3.10
3.50
2.51
2.96
2.34
2.87
6.06
6.88
STYLE 3:
PIN 1. ANODE
2. CATHODE
3. ANODE
SWITCHMODE is a trademark of Semiconductor Components Industries, LLC.
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5773−3850
http://onsemi.com
4
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
MBRF2060CT/D