LT3682 - 1A Micropower Step-Down Switching Regulator

LT3682
1A Micropower Step-Down
Switching Regulator
FEATURES
DESCRIPTION
n
The LT®3682 is an adjustable frequency (250kHz to
2.2MHz) monolithic buck switching regulator that accepts
input voltages up to 36V. A high efficiency 0.5Ω switch is
included on the device along with a boost diode and the
necessary oscillator, control, and logic circuitry. Current
mode topology is used for fast transient response and good
loop stability. A SYNC pin allows the user to synchronize the
part to an external clock, and to choose between Low Ripple
Burst Mode operation and standard PWM operation.
n
n
n
n
n
n
n
n
n
n
Wide Input Range:
Operation from 3.6V to 36V
Overvoltage Lockout Protects Circuits through
60V Transients
1A Output Current
Low Ripple Burst Mode® Operation
IQ = 75μA at 12VIN to 3.3VOUT
Output Ripple < 15mVP-P
Adjustable Switching Frequency: 250kHz to 2.2MHz
Short-Circuit Protected
Synchronizable Between 300kHz and 2.2MHz
0.8V Feedback Reference Voltage
Output Voltage 0.8V to 20V
Soft-Start Capability
Power Good Flag
Small 12-Pin Thermally Enhanced 3mm × 3mm
DFN Package
The Low Ripple Burst Mode maintains high efficiency at
low output currents while keeping output ripple below
15mV in typical applications. Shutdown reduces input
supply current to less than 1μA while a resistor and
capacitor on the RUN/SS pin provide a controlled output
voltage ramp (soft-start). A power good flag signals when
VOUT reaches 90% of the programmed output voltage.
Protection circuitry senses the current in the power switch
and external Schottky catch diode to protect the LT3682
against short-circuit conditions. Frequency foldback and
thermal shutdown provide additional protection.
APPLICATIONS
n
n
n
n
n
Automotive Battery Regulation
Automotive Entertainment Systems
Industrial Supplies
Power for Portable Products
Distributed Supply Regulation
The LT3682 is available in a 12-Pin 3mm × 3mm DFN with
exposed pad for low thermal resistance.
L, LT, LTC and LTM are registered trademarks of Linear Technology Corporation. Burst Mode
is a trademark of Linear Technology Corporation. All other trademarks are the property of their
respective owners.
TYPICAL APPLICATION
5V Step-Down Converter
Efficiency
VOUT
5V
0.9A, VIN r 6.9V
1A, VIN r 12V
VIN
6.9V TO 36V
TRANSIENT TO 60V
BD
VIN
BOOST
RUN/SS
0.22μF
VC
2.2μF
RT
16.2k
10μH
LT3682
PG
40.2k
470pF
SYNC
SW
DA
GND
PGND
VOUT = 5V
90
EFFICIENCY (%)
ON OFF
100
536k
VOUT = 3.3V
80
70
60
VIN = 12V
L = 10µH
f = 800 kHz
FB
102k
10μF
50
0
f = 800kHz
3682 TA01
0.2
0.4
0.6
LOAD CURRENT (A)
0.8
1
3682 TA01b
3682f
1
LT3682
ABSOLUTE MAXIMUM RATINGS
PIN CONFIGURATION
(Note 1)
VIN, RUN/SS Voltage (Note 2) …….……………. ....60V
BOOST Pin Voltage …………………………..…….50V
BOOST Pin Above SW Pin …………………..……..30V
FB, RT, VC Voltage ......................................................5V
SYNC …………………………….………….……. 20V
BD and PG Voltage ..…….………………..……….. 30V
Operating Junction Temperature Range (Notes 3 and 6)
LT3682E ……………….………….. . −40°C to 125°C
LT3682I ……………………………. −40°C to 125°C
Storage Temperature Range ………….. −65°C to 150°C
TOP VIEW
VC
1
12 VIN
FB
2
11 SYNC
PG
3
GND
4
BD
5
BOOST
6
13
10 RT
9 RUN/SS
8 SW
7 DA
DD PACKAGE
12-LEAD (3mm s 3mm) PLASTIC DFN
θJA = 43°C/W
EXPOSED PAD (PIN 13) IS PGND, MUST BE SOLDERED TO PCB
ORDER INFORMATION
LEAD FREE FINISH
TAPE AND REEL
PART MARKING*
PACKAGE DESCRIPTION
TEMPERATURE RANGE
LT3682EDD#PBF
LT3682EDD#TRPBF
LFDW
12-Lead (3mm × 3mm) Plastic DFN
–40°C to 125°C
LT3682IDD#PBF
LT3682IDD#TRPBF
LFDW
12-Lead (3mm × 3mm) Plastic DFN
–40°C to 125°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
Consult LTC Marketing for information on non-standard lead based finish parts.
For more information on lead free part marking, go to: http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/
ELECTRICAL CHARACTERISTICS
The l denotes specifications which apply over the full operating temperature
range, otherwise specifications are at TA = 25°C, VIN = 10V, VRUN/SS = 10V, VBD = 3.3V unless otherwise noted. (Note 3)
PARAMETER
CONDITIONS
Minimum Operating Voltage
VBD = 3.3V
VBD < 3.0V
MIN
l
l
l
VIN Overvoltage Lockout
36
TYP
MAX
UNITS
3.4
3.4
3.6
4.3
V
V
39
41
V
Quiescent Current from VIN
VRUN/SS = 0.2V
VRUN/SS = 10V, VBD = 3.3V, Not Switching
VRUN/SS = 10V, VBD = 0V, Not Switching
l
0.01
35
90
0.5
60
160
μA
μA
μA
Quiescent Current from BD Pin
VRUN/SS = 0.2V
VRUN/SS = 10V, VBD = 3.3V, Not Switching
VRUN/SS = 10V, VBD = 0V, Not Switching
l
0.01
55
0
0.5
100
5
μA
μA
μA
2.8
3
V
800
800
808
812
mV
mV
5
80
nA
0.001
0.005
%/V
Minimum BD Pin Voltage
Feedback Voltage
l
FB Pin Bias Current (Note 4)
FB Pin Voltage = 800mV
FB Voltage Line Regulation
3.6V < VIN < 36V
Error Amp gm
IVC = ±1.5μA
Error Amp Voltage Gain
l
792
780
430
μS
1300
V/V
3682f
2
LT3682
ELECTRICAL CHARACTERISTICS
The l denotes specifications which apply over the full operating temperature
range, otherwise specifications are at TA = 25°C, VIN = 10V, VRUN/SS = 10V, VBD = 3.3V unless otherwise noted. (Note 3)
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
VC Source Current
50
μA
VC Sink Current
50
μA
1.25
A/V
VC Pin to Switch Current Gain
VC Switching Threshold
0.5
0.6
1.98
0.9
225
VC Clamp Voltage
Switching Frequency
0.7
V
2.2
1
250
2.42
1.1
275
MHz
MHz
kHz
130
210
ns
1.7
1.4
2
1.66
A
A
2
RRT = 8.06kΩ
RRT = 29.4kΩ
RRT = 158kΩ
l
Minimum Switch Off-Time
Switch Current Limit (Note 7)
SYNC = 0V
SYNC = 3.3V or Clocked
Switch VCESAT
ISW = 1A
1.45
1.18
V
460
DA Pin Current to Stop OSC
1.25
1.6
mV
1.95
A
Switch Leakage Current
VSW = 0V, VIN = 60V
0.01
1
μA
Boost Schottky Diode Voltage Drop
IBSD = 50mA
720
850
mV
Boost Schottky Diode Reverse Leakage
VSW = 10V, VBD = 0
0.1
1
μA
1.7
2.5
V
10.5
17.5
mA
12
20
μA
l
Minimum Boost Voltage (Note 5)
BOOST Pin Current
ISW = 0.5A
RUN/SS Pin Current
VRUN/SS = 10V
RUN/SS Input Voltage High
2.5
V
RUN/SS Input Voltage Low
PG Leakage Current
VPG = 5V
0.1
PG Sink Current
VPG = 0.4V
PG Threshold as % of VFB
Measured at FB pin. FB Pin Voltage Rising
PG Threshold Hysteresis
Measured at FB Pin
l
100
1000
88%
90%
V
1
μA
μA
92%
12
SYNC Threshold Voltage
300
SYNC Input Frequency
0.3
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect the device
reliability and lifetime.
Note 2: Absolute Maximum Voltage at VIN and RUN/SS pins is 60V for
nonrepetitive 1 second transients, and 36V for continuous operation.
Note 3: The LT3682E is guaranteed to meet performance specifications from
0°C to 125°C junction temperature. Specifications over the −40°C to 125°C
operating junction temperature range are assured by design, characterization
and correlation with statistical process controls. The LT3682I is guaranteed
over the full −40°C to 125°C operating junction temperature range.
0.2
550
V
mV
800
mV
2.2
MHz
Note 4: Bias current flows out of the FB pin.
Note 5: This is the minimum voltage across the boost capacitor needed to
guarantee full saturation of the switch.
Note 6: This IC includes over-temperature protection that is intended
to protect the device during momentary overload conditions. Junction
temperature will exceed the maximum operating junction temperature
when over-temperature protection is active. Continuous operation above
the specified maximum operating junction temperature may impair device
reliability.
Note 7: Current limit guaranteed by design and/or correlation to static test.
Slope compensation reduces current limit at higher duty cycles.
3682f
3
LT3682
TYPICAL PERFORMANCE CHARACTERISTICS
Efficiency (VOUT = 5V, SYNC = 0V)
Efficiency (VOUT = 3.3V, SYNC = 0V)
VIN = 12V
80
90
80
EFFICIENCY (%)
60
VIN = 34V
50
40
VIN = 24V
EFFICIENCY (%)
70
70
60
50
VIN = 34V
40
VIN = 24V
30
30
10
0.1
1
10
100
LOAD CURRENT (mA)
1000
70
0.1
60
50
0.01
40
VIN = 12V
VOUT = 3.3V
L = 10μH
f = 800kHz
30
L = 10μH
f = 800kHz
20
L = 10μH
f = 800kHz
20
1
10
0.1
1
10
100
LOAD CURRENT (mA)
20
10
0.1
1000
1
No Load Supply Current
100
LOAD CURRENT (mA)
3682 G03
No Load Supply Current
120
Maximum Load Current
1.75
1000
100
SUPPLY CURRENT (μA)
800
80
60
40
TYPICAL
CATCH DIODE: DIODES, INC. B150
VIN = 12V
VOUT = 3.3V
900
1.5
700
600
LOAD CURRENT (A)
VOUT = 3.3V
INCREASED SUPPLY CURRENT
DUE TO CATCH DIODE LEAKAGE
AT HIGH TEMPERATURE
500
400
300
200
20
1.25
1
0.75
MINIMUM
0.5
SYNC = 0V
SYNC = 3.3V
100
0
0
5
10
15 20 25 30
INPUT VOLTAGE(V)
35
0
50 25
40
0.001
1000
10
3682 G02
3682 G01
0
25
50
75
TEMPERATURE(°C)
100
3682 G04
0.25
125
0
5
10
VOUT = 3.3V
L = 10μH
f = 800kHz
15
20 25 30
INPUT VOLTAGE (V)
3682 G05
Maximum Load Current
35
40
3682 G06
Maximum Load Current
Maximum Load Current
1.75
1.5
1.5
POWER LOSS(W)
VIN = 12V
80
EFFICIENCY (%)
Efficiency (VOUT = 3.3V, SYNC = 0V)
100
90
90
SUPPLY CURRENT (μA)
TA = 25°C, unless otherwise noted.
TYPICAL
TYPICAL
0.75
MINIMUM
1
0.75
MINIMUM
1.25
1
0.75
MINIMUM
0.5
SYNC = 0V
SYNC = 5V
0.25
LOAD CURRENT (A)
1
TYPICAL
1.5
1.25
LOAD CURRENT (A)
LOAD CURRENT (A)
1.25
5
10
15
0.5
VOUT = 5V
L = 10μH
f = 800kHz
20
25
30
INPUT VOLTAGE (V)
35
SYNC = 0V
SYNC = 5V
40
3682 G07
0.25
8
10
12
14
16
INPUT VOLTAGE (V)
VOUT = 5V
L = 4.7μH
f = 2MHz
18
0.50
20
3682 G08
0.25
SYNC = 0V
SYNC = 3.3V
0
5
10
VOUT = 1.8V
L = 10μH
f = 500kHz
15 20 25 30
INPUT VOLTAGE (V)
35
40
3682 G09
3682f
4
LT3682
TYPICAL PERFORMANCE CHARACTERISTICS
Switch Current Limit
(SYNC Pin Grounded)
1.9
1.9
1.7
1.7
1.5
1.3
SYNC > 0.8V
OR CLOCKED
0.9
0.7
0.5
Switch Voltage Drop
700
DC = 10%
600
1.5
1.3
VOLTAGE DROP (mV)
SYNC < 0.3V
SWITCH CURRENT LIMIT (A)
SWITCH CURRENT LIMIT (A)
Switch Current Limit
1.1
TA = 25°C, unless otherwise noted.
DC = 90%
1.1
0.9
40
60
DUTY CYCLE (%)
20
80
0.5
50
100
25
0
25
50
75
TEMPERATURE (°C)
3682 G10
Boost Pin Current
100
0
Feedback Voltage
15
10
1.25
Switching Frequency
RRT = 29.4k
1.10
800
FREQUENCY (MHz)
20
0.5
0.75
1
SWITCH CURRENT (A)
1.20
1.15
25
0.25
3682 G12
810
FEEDBACK VOLTAGE (mV)
BOOST PIN CURRENT (mA)
200
0
125
30
790
1.05
1
0.95
0.90
780
5
0.85
0
0.25
0.5
0.75
1
SWITCH CURRENT (A)
770
50
1.25
25
0 25
50
75
TEMPERATURE(°C)
3682 G13
100
0.80
50
125
25
0
25
50
75
TEMPERATURE(°C)
100
3682 G14
Frequency Foldback
125
3682 G15
Minimum Switch On-Time
Soft-Start
120
1200
2
RRT = 29.4k
1.8
800
600
400
200
100
SWITCH CURRENT LIMIT (A)
MINIMUM SWITCH ON TIME (ns)
1000
FREQUENCY (kHz)
300
3682 G11
35
0
400
100
0.7
0
500
80
60
40
20
1.6
1.4
1.2
1
0.8
0.6
0.4
0.2
0
0 100 200 300 400 500 600 700 800 900
FB PIN VOLTAGE (mV)
3682 G16
0
50
25
0
0
25
50
75
TEMPERATURE (°C)
100
125
3682 G17
0
0.5
1
1.5
2
2.5
RUN/SS PIN VOLTAGE (V)
3
3.5
3682 G18
3682f
5
LT3682
TYPICAL PERFORMANCE CHARACTERISTICS
RUN/SS Pin Current
TA = 25°C, unless otherwise noted.
Boost Diode Forward Voltage
12
1.4
10
1.2
Error Amplifier Output Current
60
8
6
4
2
40
VC PIN CURRENT (μA)
BOOST DIODE Vf (V)
RUN/SS PIN CURRENT (μA)
50
1
0.8
0.6
0.4
5
10 15 20 25 30
RUN/SS PIN VOLTAGE (V)
35
0
40
0.25
0.5
0.75
BOOST DIODE CURRENT (A)
3682 G19
Minimum Input Voltage
30
1
100
0
100
FB PIN ERROR VOLTAGE (mV)
4.5
6
200
3682 G21
Minimum Input Voltage
6.5
Maximum VIN for Full Frequency
40
35
4
3.5
3
1
10
100
LOAD CURRENT (mA)
5.5
5
TA = 85˚C
25
20
TA = 25˚C
15
4.5
VOUT = 3.3V
L = 10μH
f = 800kHz
2.5
30
VIN (V)
INPUT VOLTAGE (V)
INPUT VOLTAGE (V)
20
3682 G20
5
2
0
10
60
200
0
0
20
10
40
50
0.2
0
30
4
1000
VOUT = 5V
L = 10μH
f = 800kHz
10
100
LOAD CURRENT (mA)
1
VOUT = 3.3V
L = 10μH
f = 800kHz
SYNC = 3.3V
10
5
1000
0
0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9
LOAD CURRENT(A)
3682 G23
3682 G22
Maximum VIN for Full Frequency
3682 G24
Maximum VIN for Full Frequency
40
40
35
35
30
30
1
VC Voltages
2.5
TA = 25˚C
25
VC VOLTAGE (V)
TA = 85˚C
TA = 85˚C
VIN (V)
VIN (V)
2
20
25
20
TA = 25˚C
1
SWITCHING THRESHOLD
15
15
VOUT = 5V
L = 10μH
f = 800kHz
SYNC = 5V
10
5
CURRENT LIMIT CLAMP
1.5
10
5
0
0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9
LOAD CURRENT(A)
VOUT = 5V
L = 4.7μH
f = 2MHz
SYNC =5V
1
3682 G25
0
0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9
LOAD CURRENT(A)
0.5
1
3682 G26
0
50
25
0
25
50
75
TEMPERATURE(°C)
100
125
3682 G27
3682f
6
LT3682
TYPICAL PERFORMANCE CHARACTERISTICS
TA = 25°C, unless otherwise noted.
Switching Waveforms; Burst Mode
Power Good Threshold
THRESTHOLD VOLTAGE (%)
95
VSW
5V/DIV
90
IL
0.2A/DIV
VOUT
20mV/DIV
85
80
5μs/DIV
70
50
3682 G29
VIN = 12V; FRONT PAGE APPLICATION
ILOAD = 5mA
25
0
25
50
75
TEMPERATURE(°C)
100
125
3682 G28
Switching Waveforms; Full
Frequency Continuous Operation
Switching Waveforms; Transition
from Burst Mode to Full Frequency
VSW
5V/DIV
VSW
5V/DIV
IL
0.5A/DIV
IL
0.2A/DIV
VOUT
20mV/DIV
VOUT
20mV/DIV
1μs/DIV
VIN = 12V; FRONT PAGE APPLICATION
ILOAD = 55mA
3682 G30
1μs/DIV
3682 G31
VIN = 12V; FRONT PAGE APPLICATION
ILOAD = 500mA
3682f
7
LT3682
PIN FUNCTIONS
VC (Pin 1): The VC pin is the output of the internal error
amplifier. The voltage on this pin controls the peak switch
current. Tie an RC network from this pin to ground to
compensate the control loop.
FB (Pin 2): The LT3682 regulates the FB pin to 0.8V. Connect
the feedback resistor divider tap to this pin.
PG (Pin 3): The PG pin is the open collector output of an
internal comparator. PG remains low until the FB pin is
within 10% of the final regulation voltage. PG output is
valid when VIN is above the minimum input voltage and
RUN/SS is high.
GND (Pin 4): The GND pin is the ground of all the internal
circuitry. Tie directly to the local GND plane.
BD (Pin 5): This pin connects to the anode of the boost
Schottky diode. BD also supplies current to the LT3682’s
internal regulator.
BOOST (Pin 6): This pin is used to provide a drive voltage, higher than the input voltage, to the internal bipolar
NPN power switch. Connect a capacitor (typically 0.22μF)
between BOOST and SW.
DA (Pin 7): Connect the anode of the catch diode (D1
in Block Diagram) to this pin. Internal circuitry senses
the current through the catch diode providing frequency
foldback in extreme situations.
SW (Pin 8): The SW pin is the output of the internal power
switch. Connect this pin to the inductor, catch diode and
boost capacitor.
RUN/SS (Pin 9): The RUN/SS pin is used to put the LT3682
in shutdown mode. Tie to ground to shut down the LT3682.
Tie to 2.5V or more for normal operation. RUN/SS also
provides a soft-start function; see the Applications Information section for more information.
RT (Pin 10): Oscillator Resistor Input. Connect a resistor
from this pin to ground to set the switching frequency.
SYNC (Pin 11): This is the external clock synchronization
input. Ground this pin for low ripple Burst Mode operation
at low output loads. Tie to 0.8V or more for pulse skipping
mode operation. Tie to a clock source for synchronization.
Clock edges should have rise and fall times faster than
1μs. Note that the maximum load current depends on
which mode is chosen. See the Applications Information
section for more information.
VIN (Pin 12): The VIN pin supplies current to the LT3682’s
internal regulator and to the internal power switch. This
pin must be locally bypassed.
Exposed Pad (Pin 13): PGND. This is the power ground used
by the catch diode (D1) when its anode is connected to the
DA pin. The exposed pad must be soldered to the PCB.
3682f
8
LT3682
BLOCK DIAGRAM
VIN
12
VIN
C1
–
+
OVLO
INTERNAL 0.8V REF
THERMAL
SHUTDOWN
BD
SLOPE COMP
BOOST
R
10
OUT
RT
OSCILLATOR
250kHz-2.2MHz
OUTB
RT
11
9
3
SYNC
RUN/SS
SYNC
PG
ERROR AMP
C3
SW
L1
8
VOUT
D1
VC CLAMP
DA
7
+
–
VC
1
CC
RC
4
GND
2
R2
C2
DISABLE
+
–
0.720V
6
Q
BURST MODE
DETECT
SOFT START
+
–
S
5
CF
PGND
FB
13
R1
3682 BD
3682f
9
LT3682
OPERATION
The LT3682 is a constant frequency, current mode
step-down regulator. An oscillator, with frequency set by
RT, enables an RS flip-flop, turning on the internal power
switch. An amplifier and comparator monitor the current
flowing between the VIN and SW pins, turning the switch
off when this current reaches a level determined by the
voltage at VC. An error amplifier measures the output
voltage through an external resistor divider tied to the FB
pin and servos the VC pin. If the error amplifier’s output
increases, more current is delivered to the output; if it
decreases, less current is delivered. An active clamp on the
VC pin provides current limit. The VC pin is also clamped to
the voltage on the RUN/SS pin; soft-start is implemented
by generating a voltage ramp at the RUN/SS pin using an
external resistor and capacitor.
An internal regulator provides power to the control circuitry.
The bias regulator normally draws power from the VIN pin,
but if the BD pin is connected to an external voltage higher
than 3V, bias power will be drawn from the external source
(typically the regulated output voltage). This improves
efficiency. The RUN/SS pin is used to place the LT3682
in shutdown, disconnecting the output and reducing the
input current to less than 1μA.
The switch driver operates from either the input or from
the BOOST pin. An external capacitor and the internal boost
diode are used to generate a voltage at the BOOST pin that
is higher than the input supply. This allows the driver to
fully saturate the internal bipolar NPN power switch for
efficient operation.
To further optimize efficiency, the LT3682 automatically
switches to Burst Mode operation in light load situations.
Between bursts, all circuitry associated with controlling
the output switch is shut down, reducing the input supply
current to 75μA in a typical application.
The oscillator reduces the LT3682’s operating frequency
when the voltage at the FB pin is low. This frequency
foldback helps to control the output current during startup
and overload conditions.
Internal circuitry monitors the current flowing through the
catch diode via the DA pin and delays the generation of
new switch pulses if this current is too high (above 1.6A
nominal). This mechanism also protects the part during
short-circuit and overload conditions by keeping the current through the inductor under control.
The LT3682 contains a power good comparator which trips
when the FB pin is at 90% of its regulated value. The PG
output is an open-collector transistor that is off when the
output is in regulation, allowing an external resistor to pull
the PG pin high. Power good is valid when the LT3682 is
enabled and VIN is above the minimum input voltage.
The LT3682 has an overvoltage protection feature which
disables switching action when the VIN goes above 39V
typical (36V minimum) during transients. When switching
is disabled, the LT3682 can safely sustain transient input
voltages up to 60V.
3682f
10
LT3682
APPLICATIONS INFORMATION
FB Resistor Network
The output voltage is programmed with a resistor divider
between the output and the FB pin. Choose the resistor
values according to:
⎛V
⎞
R1= R2 ⎜ OUT − 1⎟
⎝ 0.8 V ⎠
operation is that smaller inductor and capacitor values may
be used. The disadvantages are lower efficiency, lower
maximum input voltage, and higher dropout voltage. The
highest acceptable switching frequency (fSW(MAX)) for a
given application can be calculated as follows:
fSW(MAX ) =
Reference designators refer to the Block Diagram. 1%
resistors are recommended to maintain output voltage
accuracy.
Setting the Switching Frequency
The LT3682 uses a constant frequency PWM architecture
that can be programmed to switch from 250kHz to 2.2MHz
by using a resistor tied from the RT pin to ground. A table
showing the necessary RT value for a desired switching
frequency is in Figure 1.
SWITCHING FREQUENCY (MHz)
RT VALUE (kΩ)
0.25
158
0.3
127
0.4
90.9
0.5
71.5
0.6
57.6
0.7
47.5
0.8
40.2
0.9
34
1.0
29.4
1.2
22.6
1.4
18.2
1.6
14.7
1.8
12.1
2.0
9.76
2.2
8.06
Figure 1. Switching Frequency vs. RT Value
Operating Frequency Tradeoffs
Selection of the operating frequency is a tradeoff between
efficiency, component size, minimum dropout voltage, and
maximum input voltage. The advantage of high frequency
VOUT + VD
tON(MIN)( VIN − VSW + VD )
where VIN is the typical input voltage, VOUT is the output
voltage, VD is the catch diode drop (~0.5V) and VSW is the
internal switch drop (~0.5V at max load). This equation
shows that slower switching frequency is necessary to
safely accommodate high VIN/VOUT ratio. Also, as shown
in the Input Voltage Range section, lower frequency allows
a lower dropout voltage. Input voltage range depends on
the switching frequency because the LT3682 switch has
finite minimum on and off times. An internal timer forces
the switch to be off for at least tOFF(MIN) per cycle; This
timer has a maximum value of 210ns over temp. On the
other hand, delays associated with turning off the power
switch dictate the minimum on time tON(MIN) before the
switch can be turned off; tON(MIN) has a maximum value
of 150ns over temp. The minimum and maximum duty
cycles that can be achieved taking minimum on and off
times into account are:
DCMIN = fSW tON(MIN)
DCMAX = 1− fSW tOFF(MIN)
where fSW is the switching frequency, the tON(MIN) is the
minimum switch on time (150ns), and the tOFF(MIN) is the
minimum switch off time (210ns). These equations show
that duty cycle range increases when switching frequency
is decreased.
A good choice of switching frequency should allow adequate
input voltage range (see Input Voltage Range section) and
keep the inductor and capacitor values small.
Input Voltage Range
The minimum input voltage is determined by either the
LT3682’s minimum operating voltage of ~3.6V (VBD > 3V)
or by its maximum duty cycle (see equation in Operating
3682f
11
LT3682
APPLICATIONS INFORMATION
Frequency Tradeoffs section). The minimum input voltage
due to duty cycle is:
VIN(MIN) =
VOUT + VD
−V +V
1− fSW tOFF(MIN) D SW
where VIN(MIN) is the minimum input voltage, and tOFF(MIN)
is the minimum switch off time (210ns). Note that higher
switching frequency will increase the minimum input
voltage. If a lower dropout voltage is desired, a lower
switching frequency should be used.
The maximum input voltage for LT3682 applications
depends on switching frequency, the Absolute Maximum
Ratings of the VIN and BOOST pins, and the operating
mode. The LT3682 can operate from continuous input
voltages up to 36V. Input voltage transients of up to
60V are also safely withstood. However, note that while
VIN>VOVLO (39V typical), the LT3682 will stop switching,
allowing the output to fall out of regulation.
For a given application where the switching frequency
and the output voltage are already fixed, the maximum
input voltage that guarantees optimum output voltage
ripple for that application can be found by applying the
following expression:
VIN(MAX ) =
VD + VOUT
−V +V
fSW tON(MIN) D SW
where VIN(MAX) is the maximum operating input voltage,
VOUT is the output voltage, VD is the catch diode drop
(~0.5V), VSW is the internal switch drop (~0.5V at max load),
fSW is the switching frequency (set by RT), and tON(MIN) is
the minimum switch on time (~150ns). Note that a higher
switching frequency will reduce the maximum operating
input voltage. Conversely, a lower switching frequency
will be necessary to achieve optimum operation at high
input voltages.
Special attention must be paid when the output is in startup, short-circuit, or other overload conditions. In these
cases, the LT3682 tries to bring the output in regulation by
driving lots of current into the output load. During these
events, the inductor peak current might easily reach and
even exceed the maximum current limit of the LT3682,
especially in those cases where the switch already operates
at minimum on time. The circuitry monitoring the current
through the catch diode via the DA pin prevents the switch
from turning on again if the inductor valley current is above
1.6A nominal. In these cases, the inductor peak current is
therefore the maximum current limit of the LT3682 plus
the additional current overshoot during the turn off delay
due to minimum on time:
IL(PEAK ) = 2A +
VIN(MAX ) − VOUTOL
L
• tON(MIN)
where IL(PEAK) is the peak inductor current, VIN(MAX) is
the maximum expected input voltage, L is the inductor
value, tON(MIN) is the minimum on time and VOUTOL is the
output voltage under the overload condition. The part is
robust enough to survive prolonged operation under these
conditions as long as the peak inductor current does not
exceed 3.5A. Inductor current saturation and excessive
junction temperature may further limit performance.
If the output is in regulation and no short-circuit, startup,
or overload events are expected, then input voltage transients of up to VOVLO are acceptable regardless of the
switching frequency. In this case, the LT3682 may enter
pulse skipping operation where some switching pulses
are skipped to maintain output regulation. In this mode
the output voltage ripple and inductor current ripple will
be higher than in normal operation.
Input voltage transients above VOVLO and up to 60V can
be tolerated. However, since the part will stop switching
during these transients, the output will fall out of regulation
and the output capacitor may eventually be completely
discharged. This case must be treated then as a start-up
condition as soon as VIN returns to values below VOVLO
and the part starts switching again.
Inductor Selection and Maximum Output Current
A good first choice for the inductor value is:
L = ( VOUT + VD) •
1.8
fSW
3682f
12
LT3682
APPLICATIONS INFORMATION
where fSW is the switching frequency in MHz, VOUT is the
output voltage, VD is the catch diode drop (~0.5V) and L
is the inductor value in μH.
The inductor’s RMS current rating must be greater than the
maximum load current and its saturation current should be
about 30% higher. To keep the efficiency high, the series
resistance (DCR) should be less than 0.1Ω, and the core
material should be intended for high frequency applications.
Table 1 lists several vendors and suitable types.
For robust operation in fault conditions (start-up or short
circuit) and high input voltage (>30V), the saturation
current should be chosen high enough to ensure that the
inductor peak current does not exceed 3.5A. For example,
an application running from an input voltage of 36V using a 10μH inductor with a saturation current of 2.5A will
tolerate the mentioned fault conditions.
The optimum inductor for a given application may differ
from the one indicated by this simple design guide. A larger
value inductor provides a higher maximum load current and
reduces the output voltage ripple. If your load is lower than
the maximum load current, then you can relax the value of
the inductor and operate with higher ripple current. This
allows you to use a physically smaller inductor, or one with
a lower DCR resulting in higher efficiency. Be aware that
if the inductance differs from the simple rule above, then
the maximum load current will depend on input voltage.
In addition, low inductance may result in discontinuous
mode operation, which further reduces maximum load
current. For details of maximum output current and
discontinuous mode operation, see Linear Technology’s
Application Note 44. Finally, for duty cycles greater than
50% (VOUT/VIN > 0.5), a minimum inductance is required
to avoid sub-harmonic oscillations:
L MIN = ( VOUT + VD) •
1.2
fSW
The current in the inductor is a triangle wave with an average value equal to the load current. The peak inductor
and switch current is:
I SW(PEAK ) = IL(PEAK ) = IOUT(MAX ) +
ΔIL
2
where IL(PEAK) is the peak inductor current, IOUT(MAX) is
the maximum output load current, and ΔIL is the inductor ripple current. The LT3682 limits its switch current in
order to protect itself and the system from overload faults.
Therefore, the maximum output current that the LT3682 will
deliver depends on the switch current limit, the inductor
value and the input and output voltages.
When the switch is off, the potential across the inductor
is the output voltage plus the catch diode drop. This gives
the peak-to-peak ripple current in the inductor:
ΔIL =
(1− DC) •( VOUT + VD)
L • fSW
where fSW is the switching frequency of the LT3682, DC
is the duty cycle and L is the value of the inductor.
To maintain output regulation, the inductor peak current
must be less than the LT3682’s switch current limit ILIM.
If SYNC pin is grounded ILIM is at least 1.45A at low duty
cycles and decreases to 1.1A at DC = 90%. If SYNC pin
is tied to 0.8V or more or if it is tied to a clock source for
synchronization ILIM is at least 1.18A at low duty cycles
and decreases to 0.85A at DC = 90%. The maximum output
current is also a function of the chosen inductor value
and can be approximated by the following expressions
depending on the SYNC pin configuration:
For SYNC pin grounded:
IOUT(MAX ) = ILIM −
ΔIL
ΔI
= 1.45A •(1− 0.24 • DC) − L
2
2
3682f
13
LT3682
APPLICATIONS INFORMATION
For SYNC pin tied to 0.8V or more, or tied to a clock source
for synchronization:
necessary. This can be provided with a lower performance
electrolytic capacitor.
ΔIL
ΔI
= 1.18 A •(1− 0.29 • DC) − L
2
2
Choosing an inductor value so that the ripple current is
small will allow a maximum output current near the switch
current limit.
Step-down regulators draw current from the input supply in pulses with very fast rise and fall times. The input
capacitor is required to reduce the resulting voltage
ripple at the LT3682 and to force this very high frequency
switching current into a tight local loop, minimizing EMI.
A 2.2μF capacitor is capable of this task, but only if it is
placed close to the LT3682 (see the PCB Layout section
for more information). A second precaution regarding
the ceramic input capacitor concerns the maximum input
voltage rating of the LT3682. A ceramic input capacitor
combined with trace or cable inductance forms a high-Q
(underdamped) tank circuit. If the LT3682 circuit is plugged
into a live supply, the input voltage can ring to twice its
nominal value, possibly exceeding the LT3682’s voltage
rating. For details see Application Note 88.
IOUT(MAX ) = ILIM −
Table 1. Inductor Vendors
VENDOR
URL
PART SERIES
TYPE
Murata
www.murata.com
LQH55D
TDK
www.componenttdk.com SLF7045
SLF10145
Shielded
Shielded
Toko
www.toko.com
D62CB
D63CB
D73C
D75F
Shielded
Shielded
Shielded
Open
Coilcraft
www.coilcraft.com
MSS7341
MSS1038
Shielded
Shielded
Sumida
www.sumida.com
CR54
CDRH74
CDRH6D38
CR75
Open
Shielded
Shielded
Open
Open
One approach to choosing the inductor is to start with the
simple rule given above, look at the available inductors,
and choose one to meet cost or space goals. Then use
these equations to check that the LT3682 will be able to
deliver the required output current. Note again that these
equations assume that the inductor current is continuous.
Discontinuous operation occurs when IOUT is less than
ΔIL/2.
Input Capacitor
Bypass the input of the LT3682 circuit with a ceramic capacitor of X7R or X5R type. Y5V types have poor performance
over temperature and applied voltage, and should not be
used. A 2.2μF to 10μF ceramic capacitor is adequate to
bypass the LT3682 and will easily handle the ripple current.
Note that larger input capacitance is required when a lower
switching frequency is used. If the input power source has
high impedance, or there is significant inductance due to
long wires or cables, additional bulk capacitance may be
Output Capacitor and Output Ripple
The output capacitor has two essential functions. Along
with the inductor, it filters the square wave generated by the
LT3682 to produce the DC output. In this role it determines
the output ripple, and low impedance at the switching
frequency is important. The second function is to store
energy in order to satisfy transient loads and stabilize the
LT3682’s control loop. Ceramic capacitors have very low
equivalent series resistance (ESR) and provide the best
ripple performance. A good starting value is:
COUT =
50
VOUT fSW
where fSW is in MHz, and COUT is the recommended
output capacitance in μF. Use X5R or X7R types. This
choice will provide low output ripple and good transient
response. Transient performance can be improved with
a higher value capacitor if the compensation network is
also adjusted to maintain the loop bandwidth. A lower
value of output capacitor can be used to save space
and cost but transient performance will suffer. See the
Frequency Compensation section to choose an appropriate
compensation network.
3682f
14
LT3682
APPLICATIONS INFORMATION
Table 2. Capacitor Vendors
VENDOR
PHONE
URL
PART SERIES
COMMENTS
Panasonic
(714) 373-7366
www.panasonic.com
Ceramic,
Polymer,
Tantalum
EEF Series
Kemet
(864) 963-6300
www.kemet.com
Ceramic,
Tantalum
T494, T495
Sanyo
(408)749-9714
www.sanyovideo.com
Ceramic,
Polymer,
Tantalum
POSCAP
Murata
(408)436-1300
www.murata.com
Ceramic
www.avxcorp.com
Ceramic,
Tantalum
www.taiyo-yuden.com
Ceramic
AVX
Taiyo Yuden
(864)963-6300
When choosing a capacitor, look carefully through the
data sheet to find out what the actual capacitance is under
operating conditions (applied voltage and temperature).
A physically larger capacitor, or one with a higher voltage
rating, may be required. High performance tantalum or
electrolytic capacitors can be used for the output capacitor.
Low ESR is important, so choose one that is intended for
use in switching regulators. The ESR should be specified
by the supplier, and should be 0.05Ω or less. Such a
capacitor will be larger than a ceramic capacitor and will
have a larger capacitance, because the capacitor must be
large to achieve low ESR. Table 2 lists several capacitor
vendors.
Diode Selection
The catch diode (D1 from block diagram) conducts current
only during switch off time. Average forward current in
normal operation can be calculated from:
ID( AVG) = IOUT •(1− DC)
where DC is the duty cycle. The only reason to consider a
diode with larger current rating than necessary for nominal
operation is for the case of shorted or overloaded output
conditions. For the worst case of shorted output the diode
average current will then increase to a value that depends on
the following internal parameters: switch current limit, catch
diode (DA pin) current threshold and minimum on-time. The
worst case (taking maximum values for the above mentioned
parameters) is given by the following expression:
TPS Series
1 V
ID( AVG)MAX = 2A + • IN • 150ns
2 L
Peak reverse voltage is equal to the regulator input voltage
if it is below the overvoltage protection threshold. This
feature keeps the switch off for VIN > OVLO (41V maximum). For inputs up to the maximum operating voltage
of 36V, use a diode with a reverse voltage rating greater
than the input voltage. If transients at the input of up to
60V are expected, use a diode with a reverse voltage rating only higher than the maximum OVLO of 41V. Table 3
lists several Schottky diodes and their manufacturers. If
operating at high ambient temperatures, consider using
a Schottky with low reverse leakage.
Audible Noise
Ceramic capacitors are small, robust and have very
low ESR. However, ceramic capacitors can sometimes
cause problems when used with the LT3682 due to their
piezoelectric nature. When in Burst Mode operation, the
LT3682’s switching frequency depends on the load current,
and at very light loads the LT3682 can excite the ceramic
capacitor at audio frequencies, generating audible noise.
Since the LT3682 operates at a lower current limit during
Burst Mode operation, the noise is typically very quiet. If
this is unacceptable, use a high performance tantalum or
electrolytic capacitor at the output.
3682f
15
LT3682
APPLICATIONS INFORMATION
Table 3. Schottky Diodes
VR (V)
IAVE (A)
VF at 1A (mV) VF at 2A (mV)
On Semiconducor
MBR0520L
20
0.5
MBR0540
40
0.5
620
MBRM120E
20
1
530
MBRM140
40
1
550
595
LT3682
Diodes Inc.
30
0.5
B0540W
40
0.5
620
B120
20
1
500
B130
30
1
500
CURRENT MODE
POWER STAGE
gm = 1.25S
SW
FB
–
B0530W
OUTPUT
R1
CPL
gm = 420μS
3Meg
B140
40
1
500
B150
50
1
700
B220
20
2
500
B230
30
2
500
B140HB
40
1
DFLS240L
40
2
DFLS140
40
1.1
B240
40
2
VC
CF
+
PART NUMBER
compensation is provided by the components tied to the VC
pin, as shown in Figure 2. Generally a capacitor (CC) and a
resistor (RC) in series to ground are used. In addition, there
may be a lower value capacitor in parallel. This capacitor
(CF) is used to filter noise at the switching frequency, and
is required only if a phase-lead capacitor (CPL) is used or
if the output capacitor has high ESR.
0.8V
GND
RC
CC
ESR
+
C1
C1
POLYMER
OR
TANTALUM
R2
OR
ELECTROLITIC
CERAMIC
3682 F02
500
510
500
Central Semiconductor
CMSH1 – 40M
40
1
500
CMSH1 – 60M
60
1
700
CMSH1 – 40ML
40
1
400
CMSH2 – 40M
40
2
550
CMSH2 – 60M
60
2
700
CMSH2 – 40L
40
2
400
CMSH2 – 40
40
2
500
CMSH2 – 60
60
2
700
Frequency Compensation
The LT3682 uses current mode control to regulate the
output. This simplifies loop compensation. In particular,
the LT3682 does not require the ESR of the output capacitor
for stability, so you are free to use ceramic capacitors to
achieve low output ripple and small circuit size. Frequency
Figure 2. Model for Loop Response
Loop compensation determines the stability and transient
performance. Optimizing the design of the compensation
network depends on the application and type of output
capacitor. A practical approach is to start with one of the
circuits in this data sheet that is similar to your application
and tune the compensation network to optimize the
performance. Stability should then be checked across all
operating conditions, including load current, input voltage
and temperature. The LT1375 data sheet contains a more
thorough discussion of loop compensation and describes
how to test the stability using a transient load. Figure 2
shows an equivalent circuit for the LT3682 control loop.
The error amplifier is a transconductance amplifier with
finite output impedance. The power section, consisting
of the modulator, power switch and inductor, is modeled
as a transconductance amplifier generating an output
current proportional to the voltage at the VC pin. Note that
the output capacitor integrates this current, and that the
3682f
16
LT3682
APPLICATIONS INFORMATION
capacitor on the VC pin (CC) integrates the error amplifier
output current, resulting in two poles in the loop. In most
cases a zero is required and comes from either the output
capacitor ESR or from a resistor RC in series with CC.
This simple model works well as long as the value of the
inductor is not too high and the loop crossover frequency
is much lower than the switching frequency. A phase lead
capacitor (CPL) across the feedback divider may improve
the transient response. Figure 3 shows the transient
response when the load current is stepped from 300mA
to 650mA and back to 300mA.
VOUT
100mV/DIV
ILOAD
0.5A/DIV
20μs/DIV
3682 F03
Figure 3. Transient Load Response of the LT3682.
3.3VOUT Typical Application with VIN = 12V as the
Load Current is Stepped from 300mA to 650mA.
Low Ripple Burst Mode and Pulse-Skip Mode
The LT3682 is capable of operating in either Low Ripple Burst
Mode or Pulse-Skip Mode which are selected using the SYNC
pin. See the Synchronization section for more information.
To enhance efficiency at light loads, the LT3682 can be
operated in Low Ripple Burst Mode operation which keeps
the output capacitor charged to the proper voltage while
minimizing the input quiescent current. During Burst Mode
operation, the LT3682 delivers single cycle bursts of current
to the output capacitor followed by sleep periods where
the output power is delivered to the load by the output
capacitor. Because the LT3682 delivers power to the output
with single, low current pulses, the output ripple is kept
below 15mV for a typical application. In addition, VIN and
BD quiescent currents are reduced to typically 35μA and
55μA respectively during the sleep time. As the load current
decreases towards a no load condition, the percentage of
time that the LT3682 operates in sleep mode increases and
the average input current is greatly reduced resulting in
high efficiency even at very low loads. (See Figure 4). At
higher output loads (above about 70mA for the front page
application) the LT3682 will be running at the frequency
programmed by the RT resistor, and will be operating in
standard PWM mode. The transition between PWM and
Low Ripple Burst Mode is seamless, and will not disturb
the output voltage.
If low quiescent current is not required, tie SYNC high to
select pulse-skip mode. The benefit of this mode is that the
LT3682 will enter full frequency standard PWM operation at
a lower output load current than when in Burst Mode. The
front page application circuit will switch at full frequency
at output loads higher than about 30mA. The maximum
load current that the LT3682 can supply is reduced when
SYNC is high.
VSW
5V/DIV
IL
0.2A/DIV
VOUT
20mV/DIV
5μs/DIV
3682 F04
VIN = 12V; FRONT PAGE APPLICATION
ILOAD = 5mA
Figure 4. Burst Mode Operation
3682f
17
LT3682
APPLICATIONS INFORMATION
BOOST and BD Pin Considerations
Capacitor C3 and the internal boost Schottky diode (see
the Block Diagram) are used to generate a boost voltage that is higher than the input voltage. In most cases
a 0.22μF capacitor will work well. Figure 5 shows three
ways to arrange the boost circuit. The BOOST pin must
be more than 2.3V above the SW pin for best efficiency.
For outputs of between 3V and 8V, the standard circuit
(Figure 5a) is best. For outputs between 2.8V and 3V, use
a 1μF boost capacitor. A 2.5V output presents a special
case because it is marginally adequate to support the
boosted drive stage while using the internal boost diode.
For reliable BOOST pin operation with 2.5V outputs use
a good external Schottky diode (such as the ON Semi
MBR0540), and a 1μF boost capacitor (see Figure 5b).
For lower output voltages the boost diode can be tied to
the input (Figure 5c), or to another supply greater than
2.8V. Keep in mind that a minimum input voltage of 4.3V
is required if the voltage at the BD pin is smaller than 3V.
Tying BD to VIN reduces the maximum input voltage to
25V. The circuit in Figure 5a is more efficient because the
BOOST pin current and BD pin quiescent current come
from a lower voltage source. You must also be sure that
the maximum voltage ratings of the BOOST and BD pins
are not exceeded.
As mentioned, a minimum of 2.5V across the BOOST
capacitor is required for proper operation of the internal
BOOST circuitry to provide the base current for the power
NPN switch. For BD pin voltages higher than 3V, the excess
voltage across the BOOST capacitor does not bring an
increase in performance but dissipates additional power in
the internal BOOST circuitry instead. The BOOST circuitry
tolerates reasonable amounts of power, however excessive
power dissipation on this circuitry may impair reliability. For
reliable operation, use no more than 8V on the BD pin for
the circuit in Figure 5a. For higher output voltages, make
sure that there is no more than 8V at the BD pin either by
connecting it to another available supply higher than 3V or
by using a Zener diode between VOUT and BD to maintain
the BD pin voltage between 3V and 8V.
The minimum operating voltage of an LT3682 application is limited by the minimum input voltage and by the
maximum duty cycle as outlined previously. For proper
startup, the minimum input voltage is also limited by the
boost circuit. If the input voltage is ramped slowly, or the
LT3682 is turned on with its RUN/SS pin when the output
VOUT
BD
BOOST
VIN
VIN
LT3682
C3
SW
D1
DA
PGND
GND
(5a) For VOUT > 2.8V; VIN(MIN) = 4.3V if VOUT < 3V
VOUT
D2
BD
BOOST
VIN
VIN
LT3682
C3
SW
D1
DA
PGND
GND
(5b) For 2.5V < VOUT < 2.8V; VIN(MIN) = 4.3V
VOUT
BD
BOOST
VIN
VIN
LT3682
C3
SW
D1
DA
GND
PGND
(5c) For VOUT < 2.5V; VIN(MAX) = 25V
3682 F05
Figure 5. Three Circuits For Generating The Boost Voltage
3682f
18
LT3682
APPLICATIONS INFORMATION
is already in regulation, then the boost capacitor may not
be fully charged. Because the boost capacitor is charged
with the energy stored in the inductor, the circuit will rely
on some minimum load current to get the boost circuit
running properly. This minimum load will depend on input
and output voltages, and on the arrangement of the boost
circuit. The minimum load generally goes to zero once the
circuit has started. Figure 6 shows a plot of minimum load
to start and to run as a function of input voltage. In many
6
5.5
TO START
(WORST CASE)
INPUT VOLTAGE (V)
5
4.5
Soft-Start
4
3.5
TO RUN
3
VOUT = 3.3V
TA = 25˚C
L = 10μH
f = 800kHz
2.5
2
10
100
LOAD CURRENT (mA)
1
1000
8
7.5
TO START
(WORST CASE)
7
INPUT VOLTAGE (V)
cases the discharged output capacitor will present a load
to the switcher, which will allow it to start. The plots show
the worst-case situation where VIN is ramping very slowly.
For lower start-up voltage, the boost diode can be tied to
VIN; however, this restricts the input range to one-half of
the absolute maximum rating of the BOOST pin. At light
loads, the inductor current becomes discontinuous and
the effective duty cycle can be very high. This reduces the
minimum input voltage to approximately 300mV above
VOUT. At higher load currents, the inductor current is
continuous and the duty cycle is limited by the maximum
duty cycle of the LT3682, requiring a higher input voltage
to maintain regulation.
6.5
6
The RUN/SS pin can be used to soft-start the LT3682,
reducing the maximum input current during start-up. The
RUN/SS pin is driven through an external RC network to
create a voltage ramp at this pin. Figure 7 shows the startup
and shut-down waveforms with the soft-start circuit. By
choosing a large RC time constant, the peak start-up
current can be reduced to the current that is required to
regulate the output, with no overshoot. Choose the value
of the resistor so that it can supply 20μA when the RUN/SS
pin reaches 2.5V.
5.5
5 TO RUN
VRUN
5V/DIV
4.5
4
3.5
VOUT = 5V
TA = 25˚C
L = 10μH
f = 800kHz
3
2.5
2
1
10
100
LOAD CURRENT(mA)
1000
3682 F06
Figure 6. The Minimum Input Voltage Depends on
Output Voltage, Load Current and Boost Circuit
RUN
15k
VRUN/SS
5V/DIV
RUN/SS
0.22μF
GND
VOUT
5V/DIV
IL
1A/DIV
5ms/DIV
3682 F07
Figure 7. To Soft-Start the LT3682, Add a
Resistor and Capacitor to the RUN/SS Pin
3682f
19
LT3682
APPLICATIONS INFORMATION
Synchronization
To select Low Ripple Burst Mode operation, tie the SYNC
pin below 0.3V (this can be ground or a logic output).
Synchronizing the LT3682 oscillator to an external
frequency can be done by connecting a square wave (with
20% to 80% duty cycle) to the SYNC pin. The square wave
amplitude should have valleys that are below 0.3V and
peaks that are above 0.8V (up to 6V).
The LT3682 will not enter Burst Mode at low output loads
while synchronized to an external clock, but instead will
skip pulses to maintain regulation.
The maximum load current that the part can supply is
reduced when a clock signal is applied to SYNC.
The LT3682 may be synchronized over a 300kHz to 2.2MHz
range. The RT resistor should be chosen to set the LT3682
switching frequency 20% below the lowest synchronization
input. For example, if the synchronization signal will be
360kHz, the RT should be chosen for 300kHz. To assure
reliable and safe operation the LT3682 will only synchronize
when the output voltage is near regulation as indicated
by the PG flag. It is therefore necessary to choose a large
enough inductor value to supply the required output current
at the frequency set by the RT resistor. See the Inductor
Selection section for more information. It is also important
to note that slope compensation is set by the RT value:
to avoid subharmonics, calculate the minimum inductor
value using the frequency determined by RT.
Shorted and Reversed Input Protection
If the inductor is chosen so that it won’t saturate excessively,
the LT3682 will tolerate a shorted output. When operating
in short-circuit condition, the LT3682 will reduce its
frequency until the valley current is at a typical value of
1.6A (see Figure 8). There is another situation to consider
in systems where the output will be held high when the
input to the LT3682 is absent. This may occur in battery
charging applications or in battery backup systems where
a battery or some other supply is diode OR-ed with the
LT3682’s output. If the VIN pin is allowed to float and the
RUN/SS pin is held high (either by a logic signal or because
it is tied to VIN), then the LT3682’s internal circuitry will
pull its quiescent current through its SW pin. This is fine
if your system can tolerate a few mA in this state. If you
ground the RUN/SS pin, the SW pin current will drop to
essentially zero. However, if the VIN pin is grounded while
the output is held high, then parasitic diodes inside the
LT3682 can pull large currents from the output through
the SW pin and the VIN pin. Figure 9 shows a circuit that
will run only when the input voltage is present and that
protects against a shorted or reversed input.
D4
MBRS140
VIN
BD
VIN
BOOST
LT3682
VSW
20V/DIV
0V
IL
500mA/DIV
RUN/SS
VC
VOUT
SW
DA
GND PGND FB
BACKUP
3682 F09
0A
2μs/DIV
3682 F08
Figure 8. The LT3682 Reduces its Frequency to
Protect Against Shorted Output with 36V Input
Figure 9. Diode D4 Prevents a Shorted Input from
Discharging a Backup Battery Tied to the Output.
It Also Protects the Circuit from a Reversed Input.
The LT3682 Runs Only When the Input is Present
3682f
20
LT3682
APPLICATIONS INFORMATION
PCB Layout
For proper operation and minimum EMI, care must be taken
during printed circuit board layout. Figure 10 shows the
recommended component placement with trace, ground
plane and via locations. Note that large, switched currents
flow in the LT3682’s VIN, SW and PGND pins, the catch
diode and the input capacitor (CIN). The loop formed by
these components should be as small as possible. These
components, along with the inductor and output capacitor
(COUT), should be placed on the same side of the circuit
board, and their connections should be made on that layer.
All connections to GND should be made at a common
star ground point or directly to a local, unbroken ground
plane below these components. The SW and BOOST nodes
should be laid out carefully to avoid interference. If the
part is synchronized externally using the SYNC pin, care
must be taken laying out this signal to avoid interference
with sensitive nodes, especially VC, FB, and RT. Finally,
keep the FB, RT, and VC nodes small so that the ground
traces will shield them from the SW and BOOST nodes.
The exposed pad Pin 13 on the bottom of the package
acts as a heat sink and must be soldered to the ground
node. To keep thermal resistance low, extend the ground
plane as much as possible and add thermal vias under and
near the LT3682 to any additional ground planes within
the circuit board and on the bottom side. Keep in mind
that the thermal design must keep the junctions of the
IC below the specified absolute maximum temperature
of 125°C.
High Temperature Considerations
The PCB must provide heat sinking to keep the LT3682
cool. The exposed pad on the bottom of the package must
be soldered to a copper area, which in turn should be
tied to large copper layers below with thermal vias; these
layers will spread the heat dissipated by the LT3682. Place
additional vias to reduce thermal resistance further. With
these steps, the thermal resistance from die (or junction)
to ambient can be reduced to θJA = 35°C/W or less. With
100 LFPM airflow, this resistance can fall by another 25%.
Further increases in airflow will lead to lower thermal
resistance. Because of the large output current capability of
VOUT
L
C2
D1
GND
C1
VIN
GND
3682 F10
Figure 10. A Good PCB Layout Ensures Proper, Low EMI Operation
the LT3682, it is possible to dissipate enough heat to raise
the junction temperature beyond the absolute maximum of
125°C. When operating at high ambient temperatures, the
maximum load current should be derated as the ambient
temperature approaches these maximums. If the junction
temperature reaches the thermal shutdown threshold, the
part will stop switching to prevent internal damage due
to overheating.
Power dissipation within the LT3682 can be estimated
by calculating the total power loss from an efficiency
measurement. The die temperature is calculated by
multiplying the LT3682 power dissipation by the thermal
resistance from junction to ambient.
Other Linear Technology Publications
Application Notes 19, 35 and 44 contain more detailed
descriptions and design information for buck regulators
and other switching regulators. The LT1376 data sheet
has a more extensive discussion of output ripple, loop
compensation and stability testing. Design Note 318
shows how to generate a bipolar output supply using a
buck regulator.
3682f
21
LT3682
TYPICAL APPLICATIONS
5V Step-Down Converter
VIN
6.9V TO 36V
TRANSIENT
TO 60V
BD
VIN
ON OFF
VOUT
5V
0.9A, VIN 6.9V
1A, VIN 12V
RUN/SS
BOOST
L
10μH
0.22μF
VC
2.2μF
SW
LT3682
RT
16.2k
DA
D1
B150
PG
40.2k
536k
SYNC
GND
FB
PGND
102k
470pF
10μF
3682 TA02
f = 800kHz
3.3V Step-Down Converter
VIN
4.8V TO 28.5V
TRANSIENT
TO 60V
BD
VIN
ON OFF
VOUT
3.3V
0.9A, VIN 4.8V
1A, VIN 6.5V
RUN/SS
BOOST
L
10μH
0.22μF
VC
2.2μF
SW
LT3682
RT
14k
DA
D1
B150
PG
40.2k
SYNC
GND
316k
FB
PGND
470pF
102k
10μF
3682 TA03
f = 800kHz
1.8V Step-Down Converter
VIN
3.6V TO 25V
VIN
ON OFF
BD
RUN/SS
BOOST
0.22μF
VC
4.7μF
LT3682
RT
17.4k
L
6.8μH
SW
DA
D1
B140
VOUT
1.8V
1A
PG
71.5k
SYNC
GND
127k
FB
PGND
330pF
102k
f = 500kHz
22μF
3682 TA04
3682f
22
LT3682
PACKAGE DESCRIPTION
DD Package
12-Lead Plastic DFN (3mm × 3mm)
(Reference LTC DWG # 05-08-1725 Rev A)
0.70 p0.05
3.50 p0.05
2.10 p0.05
2.38 p0.05
1.65 p0.05
PACKAGE
OUTLINE
0.25 p 0.05
0.45 BSC
2.25 REF
RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS
APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED
3.00 p0.10
(4 SIDES)
R = 0.115
TYP
7
0.40 p 0.10
12
2.38 p0.10
1.65 p 0.10
PIN 1 NOTCH
R = 0.20 OR
0.25 s 45o
CHAMFER
PIN 1
TOP MARK
(SEE NOTE 6)
6
0.200 REF
1
0.23 p 0.05
0.45 BSC
0.75 p0.05
2.25 REF
(DD12) DFN 0106 REV A
0.00 – 0.05
BOTTOM VIEW—EXPOSED PAD
NOTE:
1. DRAWING IS NOT A JEDEC PACKAGE OUTLINE
2. DRAWING NOT TO SCALE
3. ALL DIMENSIONS ARE IN MILLIMETERS
4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE
MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE
5. EXPOSED PAD AND TIE BARS SHALL BE SOLDER PLATED
6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE
TOP AND BOTTOM OF PACKAGE
3682f
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
23
LT3682
TYPICAL APPLICATIONS
5V, 2MHz Step-Down Converter
VIN
10V TO 16.5V
TRANSIENT TO 36V
BD
VIN
ON OFF
VOUT
5V
0.9A
RUN/SS
BOOST
0.22μF
VC
2.2μF
LT3682
RT
13.3k
L
4.7μH
SW
DA
D1
B140
PG
9.76k
SYNC
GND
536k
FB
PGND
680pF
102k
f = 2MHz
10μF
3682 TA05
RELATED PARTS
PART NUMBER
DESCRIPTION
COMMENTS
LT1766
60V, 1.2A (IOUT), 200kHz, High Efficiency Step-Down DC/DC
Converter
VIN = 5.5V to 60V, VOUT(MIN) = 1.2V, IQ = 2.5mA, ISD = 25μA,
TSSOP16E Package
LT1767
25V, 1.2A (IOUT), 1.2MHz High Efficiency Step-Down DC/DC
Converter
VIN = 3V to 25V, VOUT(MIN) = 1.2V, IQ = 1mA, ISD < 6μA,
MS8E Package
LT1933
500mA (IOUT), 500kHz Step-Down DC/DC Converter
VIN = 3.6V to 36V, VOUT(MIN) = 1.2V, IQ = 1.6mA, ISD < 1μA,
TM
ThinSOT Package
LT1936
36V, 1.4A (IOUT), 500kHz High Efficiency Step-Down DC/DC
Converter
VIN = 3.6V to 36V, VOUT(MIN) = 1.2V, IQ = 1.9mA, ISD < 1μA,
MS8E Package
LT1940
Dual 25A, 1.4A (IOUT), 1.1MHz, High Efficiency Step-Down
DC/DC Converter
VIN = 3.6V to 25V, VOUT(MIN) = 1.2V, IQ = 3.8mA, ISD < 30μA,
TSSOP16E Package
LT1976/LT1967
60V, 1.2A (IOUT), 200kHz/500kHz, High Efficiency Step-Down
DC/DC Converters with Burst Mode Operation
VIN = 3.3V to 60V, VOUT(MIN) = 1.2V, IQ = 100μA, ISD < 1μA,
TSSOP16E Package
LT3434/LT3435
60V, 2.4A (IOUT), 200kHz/500kHz, High Efficiency Step-Down
DC/DC Converters with Burst Mode Operation
VIN = 3.3V to 60V, VOUT(MIN) = 1.2V, IQ = 100μA, ISD < 1μA,
TSSOP16 Package
LT3437
60V, 400mA (IOUT), Micropower Step-Down DC/DC Converter
with Burst Mode Operation
VIN = 3.3V to 60V, VOUT(MIN) = 1.25V, IQ = 100μA, ISD < 1μA,
3mm × 3mm DFN10 and TSSOP16E Packages
LT3480
36V with Transient Protection to 60V, 2A (IOUT), 2.4MHz, High
VIN = 3.6V to 38V, VOUT(MIN) = 0.78V, IQ = 70μA, ISD < 1μA,
Efficiency Step-Down DC/DC Converter with Burst Mode Operation 3mm × 3mm DFN10 and MSOP10E Packages
LT3481
34V with Transient Protection to 36V, 2A (IOUT), 2.8MHz, High
VIN = 3.6V to 34V, VOUT(MIN) = 1.26V, IQ = 50μA, ISD < 1μA,
Efficiency Step-Down DC/DC Converter with Burst Mode Operation 3mm × 3mm DFN10 and MSOP10E Packages
LT3493
36V, 1.4A (IOUT), 750kHz High Efficiency Step-Down
DC/DC Converter
VIN = 3.6V to 36V, VOUT(MIN) = 0.8V, IQ = 1.9mA, ISD < 1μA,
2mm × 3mm DFN8 and MSOP8E Packages
LT3505
36V with Transient Protection to 40V, 1.4A (IOUT), 3MHz,
High Efficiency Step-Down DC/DC Converter
VIN = 3.6V to 34V, VOUT(MIN) = 0.78V, IQ = 2mA, ISD = 2μA,
3mm × 3mm DFN6 Package
LT3508
36V with Transient Protection to 40V, Dual 1.4A (IOUT), 3MHz,
High Efficiency Step-Down DC/DC Converter
VIN = 3.7V to 37V, VOUT(MIN) = 0.8V, IQ = 4.6mA, ISD = 1μA,
4mm × 4mm QFN24 and TSSOP16E Packages
LT3684
34V with Transient Protection to 36V, 2A (IOUT), 2.8MHz,
High Efficiency Step-Down DC/DC Converter
VIN = 3.6V to 34V, VOUT(MIN) = 1.26V, IQ = 850mA, ISD < 1μA,
3mm × 3mm DFN10 and MSOP10E Packages
LT3685
36V with Transient Protection to 60V, Dual 2A (IOUT), 2.4MHz,
High Efficiency Step-Down DC/DC Converter
VIN = 3.6V to 38V, VOUT(MIN) = 0.78V, IQ = 70mA, ISD < 1μA,
3mm × 3mm DFN10 and MSOP10E Packages
ThinSOT is a trademark of Linear Technology Corporation.
3682f
24 Linear Technology Corporation
LT 1208 • PRINTED IN USA
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900 ● FAX: (408) 434-0507
●
www.linear.com
© LINEAR TECHNOLOGY CORPORATION 2008