AD ADG728BRUZ

a
CMOS, Low Voltage, 2-Wire
Serially Controlled, Matrix Switches
ADG728/ADG729
FEATURES
2-Wire Serial Interface
2.7 V to 5.5 V Single Supply
2.5 Ω On Resistance
0.75 Ω On-Resistance Flatness
100 pA Leakage Currents
Single 8-to-1 Matrix Switch ADG728
Dual 4-to-1 Matrix Switch ADG729
Power-On Reset
Small 16-Lead TSSOP Package
Qualified for Automotive Applications
APPLICATIONS
Data Acquisition Systems
Communications Systems
Relay Placement
Audio and Video Switching
Automatic Test Equipment
FUNCTIONAL BLOCK DIAGRAMS
ADG728
ADG729
S1
S1A
DA
S4A
D
S1B
DB
S4B
S8
INPUT SHIFT
REGISTER
INPUT SHIFT
REGISTER
RESET
SDA SCL A0
A1
GENERAL DESCRIPTION
PRODUCT HIGHLIGHTS
The ADG728 and ADG729 are CMOS analog matrix switches
with a serially controlled 2-wire interface. The ADG728 is an
8-channel matrix switch, while the ADG729 is a dual 4-channel
matrix switch. On resistance is closely matched between switches
and very flat over the full signal range. These parts can operate
equally well as either multiplexers, demultiplexers or switch
arrays and the input signal range extends to the supplies.
1. 2-Wire Serial Interface.
The ADG728 and ADG729 utilize a 2-wire serial interface that
is compatible with the I2C™ interface standard. Both have two
external address pins (A0 and A1). This allows the 2 LSBs of
the 7-bit slave address to be set by the user. Four of each of the
devices can be connected to the one bus. The ADG728 also has
a RESET pin that should be tied high if not in use.
SDA SCL A0
A1
2. Single Supply Operation. The ADG728 and ADG729 are
fully specified and guaranteed with 3 V and 5 V supply rails.
3. Low On Resistance 2.5 Ω typical.
4. Any configuration of switches may be on at any one time.
5. Guaranteed Break-Before-Make Switching Action.
6. Small 16-Lead TSSOP Package.
Each channel is controlled by one bit of an 8-bit word. This
means that these devices may be used in a number of different
configurations; all, any, or none of the channels may be on at
any one time.
On power-up of the device, all switches will be in the OFF condition and the internal shift register will contain all zeros.
All channels exhibit break-before-make switching action preventing momentary shorting when switching channels.
The ADG728 and ADG729 are available in 16-lead TSSOP
packages.
REV. C
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
www.analog.com
Fax: 781/461-3113
© Analog Devices, Inc., 2012
ADG728/ADG729–SPECIFICATIONS1 (V
Parameter
ANALOG SWITCH
Analog Signal Range
On Resistance (RON)
On-Resistance Match Between
Channels (∆RON)
On-Resistance Flatness (RFLAT(ON))
B Version
–40ⴗC
25ⴗC
to +85ⴗC
0 V to VDD
2.5
4.5
5
0.4
0.8
0.75
1.2
LEAKAGE CURRENTS
Source OFF Leakage IS (OFF)
Drain OFF Leakage ID (OFF)
Channel ON Leakage ID, IS (ON)
LOGIC INPUTS (A0, A1)2
Input High Voltage, VINH
Input Low Voltage, VINL
Input Current
IINL or IINH
CIN, Input Capacitance
± 0.01
± 0.1
± 0.01
± 0.1
± 0.01
± 0.1
0.005
IIN, Input Leakage Current
0.005
VHYST, Input Hysteresis
CIN, Input Capacitance
0.05 VDD
6
LOGIC OUTPUT (SDA)2
VOL, Output Low Voltage
DYNAMIC CHARACTERISTICS2
tON
Unit
V
Ω typ
Ω max
Ω typ
Ω max
Ω typ
Ω max
±1
2.4
0.8
V min
V max
± 0.1
µA typ
µA max
pF typ
± 0.3
±1
0.7 VDD
VDD + 0.3
–0.3
0.3 VDD
Input Low Voltage, VINL
= 5 V ⴞ 10%, GND = 0 V, unless otherwise noted.)
nA typ
nA max
nA typ
nA max
nA typ
nA max
6
LOGIC INPUTS (SCL, SDA)2
Input High Voltage, VINH
DD
± 1.0
0.4
0.6
95
140
V min
V max
V min
V max
µA typ
µA max
V min
pF typ
Charge Injection
±3
Off Isolation
–55
–75
dB typ
dB typ
Channel-to-Channel Crosstalk
–55
–75
dB typ
dB typ
65
100
13
MHz typ
MHz typ
pF typ
85
42
pF typ
pF typ
96
48
pF typ
pF typ
10
µA typ
µA max
20
VD = 4.5 V/1 V, VD = 1 V/4.5 V, Test Circuit 3
VD = VS = 4.5 V/1 V, Test Circuit 4
VIN = 0 V to VDD
RL = 300 Ω, CL = 35 pF, Test Circuit 5;
VS1 = 3 V
VS1 = 3 V, RL = 300 Ω, CL = 35 pF;
Test Circuit 5
RL = 300 Ω, CL = 35 pF;
VS1 = VS2 = 3 V, Test Circuit 5
VS = 2.5 V, RS = 0 Ω, CL = 1 nF;
Test Circuit 6
RL = 50 Ω, CL = 5 pF, f = 10 MHz;
RL = 50 Ω, CL = 5 pF, f = 1 MHz;
Test Circuit 8
RL = 50 Ω, CL = 5 pF, f = 10 MHz;
RL = 50 Ω, CL = 5 pF, f = 1 MHz;
Test Circuit 7
8
POWER REQUIREMENTS
IDD
VDD = 5.5 V
VD = 4.5 V/1 V, VS = 1 V/4.5 V, Test Circuit 2
ns typ
ns max
ns typ
ns max
ns typ
ns min
pC typ
Break-Before-Make Time Delay, tD
–3 dB Bandwidth
ADG728
ADG729
CS (OFF)
CD (OFF)
ADG728
ADG729
CD, CS (ON)
ADG728
ADG729
VS = 0 V to VDD, IS = 10 mA
ISINK = 3 mA
ISINK = 6 mA
85
1
VS = 0 V to VDD, IS = 10 mA;
Test Circuit 1
VS = 0 V to VDD, IS = 10 mA
V max
V max
tOFF
130
Test Conditions/Comments
RL = 50 Ω, CL = 5 pF, Test Circuit 8
VDD = 5.5 V
Digital Inputs = 0 V or 5.5 V
NOTES
1
Temperature range is as follows: B Version: –40°C to +85°C.
Guaranteed by design, not subject to production test.
2
–2–
REV. C
1
SPECIFICATIONS
ADG728/ADG729
(VDD = 3 V ⴞ 10%, GND = 0 V, unless otherwise noted.)
B Version
Parameter
ANALOG SWITCH
Analog Signal Range
On Resistance (RON)
25ⴗC
0 V to VDD
6
11
On-Resistance Match Between
Channels (∆RON)
On-Resistance Flatness (RFLAT(ON))
LEAKAGE CURRENTS
Source OFF Leakage IS (OFF)
Drain OFF Leakage ID (OFF)
Channel ON Leakage ID, IS (ON)
LOGIC INPUTS (A0, A1)2
Input High Voltage, VINH
Input Low Voltage, VINL
Input Current
IINL or IINH
CIN, Input Capacitance
LOGIC INPUTS (SCL, SDA)2
Input High Voltage, VINH
± 0.01
± 0.1
± 0.01
± 0.1
± 0.01
± 0.1
0.005
VHYST, Input Hysteresis
CIN, Input Capacitance
LOGIC OUTPUT (SDA)2
VOL, Output Low Voltage
DYNAMIC CHARACTERISTICS2
tON
12
0.4
1.2
3.5
V
Ω typ
Ω max
Ω typ
Ω max
Ω typ
±1
2.0
0.4
V min
V max
± 0.1
µA typ
µA max
pF typ
± 0.3
±1
0.7 VDD
VDD + 0.3
–0.3
0.3 VDD
0.005
Unit
nA typ
nA max
nA typ
nA max
nA typ
nA max
3
Input Low Voltage, VINL
IIN, Input Leakage Current
–40ⴗC
to +85ⴗC
± 1.0
0.05 VDD
3
0.4
0.6
130
200
V min
V max
V min
V max
µA typ
µA max
V min
pF typ
Charge Injection
±3
Off Isolation
–55
–75
dB typ
dB typ
Crosstalk
–55
–75
dB typ
dB typ
65
100
13
MHz typ
MHz typ
pF typ
85
42
pF typ
pF typ
96
48
pF typ
pF typ
10
µA typ
µA max
NOTES
1
Temperature ranges are as follows: B Versions: –40°C to +85°C.
2
Guaranteed by design, not subject to production test.
REV. C
–3–
VD = 3 V/1 V, VD = 1 V/3 V, Test Circuit 3
VD = VS = 3 V/1 V, Test Circuit 4
VIN = 0 V to VDD
RL = 300 Ω, CL = 35 pF, Test Circuit 5;
VS1 = 2 V
RL = 300 Ω, CL = 35 pF;
VS = 2 V, Test Circuit 5
RL = 300 Ω, CL = 35 pF;
VS1 = VS8 = 2 V, Test Circuit 5
VS = 1.5 V, RS = 0 Ω, CL = 1 nF;
Test Circuit 6
RL = 50 Ω, CL = 5 pF, f = 10 MHz;
RL = 50 Ω, CL = 5 pF, f = 1 MHz;
Test Circuit 8
RL = 50 Ω, CL = 5 pF, f = 10 MHz;
RL = 50 Ω, CL = 5 pF, f = 1 MHz;
Test Circuit 7
8
20
VDD = 3.3 V
VS = 3 V/1 V, VD = 1 V/3 V, Test Circuit 2
ns typ
ns max
ns typ
ns max
ns typ
ns min
pC typ
Break-Before-Make Time Delay, tD
–3 dB Bandwidth
ADG728
ADG729
CS (OFF)
CD (OFF)
ADG728
ADG729
CD, CS (ON)
ADG728
ADG729
POWER REQUIREMENTS
IDD
VS = 0 V to VDD, IS = 10 mA
ISINK = 3 mA
ISINK = 6 mA
115
1
VS = 0 V to VDD, IS = 10 mA;
Test Circuit 1
VS = 0 V to VDD, IS = 10 mA
V max
V max
tOFF
180
Test Conditions/Comments
RL = 50 Ω, CL = 5 pF, Test Circuit 8
VDD = 3.3 V
Digital Inputs = 0 V or 3.3 V
ADG728/ADG729
TIMING CHARACTERISTICS
VDD = 2.7 V to 5.5 V. All specifications −40°C to +85°C, unless otherwise noted. See Figure 1.
Parameter
fSCL
t1
t2
t3
t4
t5
t6 1
Limit at TMIN, TMAX
400
2.5
0.6
1.3
0.6
100
0.9
0
0.6
0.6
1.3
300
20 + 0.1Cb 2
250
300
0.1Cb2
400
50
t7
t8
t9
t10
t11
Cb2
tSP 3
Unit
kHz max
µs min
µs min
µs min
µs min
ns min
µs max
µs min
µs min
µs min
µs min
ns max
ns min
ns max
ns max
ns min
pF max
ns max
Test Conditions/Comments
SCL clock frequency
SCL cycle time
SCL high time, tHIGH
SCL low time, tLOW
Start/repeated start condition hold time, tHD, STA
Data setup time, tSU, DAT
Data hold time, tHD, DAT
Setup time for repeated start, tSU, STA
Stop condition setup time, tSU, STO
Bus free time between a stop condition and a start condition, tBUF
Rise time of both SCL and SDA when receiving, tR
Fall time of SDA when receiving, tF
Fall time of SDA when transmitting, tF
Capacitive load for each bus line
Pulse width of spike suppressed
A master device must provide a hold time of at least 300 ns for the SDA signal (referred to the VIH min of the SCL signal) to bridge the undefined region of the falling
edge of SCL.
2
Cb is the total capacitance of one bus line in pF. tR and tF measured between 0.3 VDD and 0.7 VDD.
3
Input filtering on both the SCL and SDA inputs suppress noise spikes that are less than 50 ns.
1
SDA
t3
t9
t4
t 11
t 10
SCL
START
CONDITION
t6
t2
START
CONDITION
t5
t7
REPEATED
START
CONDITION
t1
t8
STOP
CONDITION
01002-002
t4
Figure 1. 2-Wire Serial Interface Timing Diagram
–4–
REV. C
ADG728/ADG729
PIN FUNCTION DESCRIPTIONS
ADG728
ADG729
Mnemonic
Function
1
1
SCL
Serial Clock Line. This is used in conjunction with the SDA line to clock data into
the 8-bit input shift register. Clock rates of up to 400 kbit/s can be accommodated
with this 2-wire serial interface.
Active low control input that clears the input register and turns all switches to the
OFF condition.
Serial Data Line. This is used in conjunction with the SCL line to clock data into
the 8-bit input shift register during the write cycle and used to read back 1 byte of
data during the read cycle. It is a bidirectional open-drain data line which should be
pulled to the supply with an external pull-up resistor.
Source. May be an input or output.
Drain. May be an input or output.
Source. May be an input or output.
Power Supply Input. These parts can be operated from a supply of 2.7 V to 5.5 V.
Ground Reference.
Address Input. Sets the second least significant bit of the 7-bit slave address.
Address Input. Sets the least significant bit of the 7-bit slave address.
RESET
2
3
3
SDA
4, 5, 6, 7
8
9, 10, 11, 12
13
14
15
16
4, 5, 6, 7
8, 9
10, 11, 12, 13
14
15
2
16
Sxx
Dx
Sxx
VDD
GND
A1
A0
PIN CONFIGURATIONS
ADG729
ADG728
SCL 1
16 A0
SCL 1
RESET 2
15 A1
A1 2
SDA 3
ADG728
S1 4
S2 5
15 GND
14 VDD
14 GND
SDA 3
13 VDD
S1A 4
12 S5
S2A 5
11 S3B
ADG729
13 S1B
TOP VIEW
(Not to Scale)
12 S2B
11 S6
S3A 6
S4 7
10 S7
S4A 7
10 S4B
D 8
9 S8
DA 8
9 DB
S3 6
REV. C
TOP VIEW
(Not to Scale)
16 A0
–5–
ADG728/ADG729
ABSOLUTE MAXIMUM RATINGS 1
(TA = 25°C unless otherwise noted.)
VDD to GND . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +7 V
Analog, Digital Inputs2 . . . . . . . . . . –0.3 V to VDD + 0.3 V or
30 mA, Whichever Occurs First
Peak Current, S or D . . . . . . . . . . . . . . . . . . . . . . . . . . 100 mA
(Pulsed at 1 ms, 10% Duty Cycle max)
Continuous Current, Each S . . . . . . . . . . . . . . . . . . . . . 30 mA
Continuous Current D, ADG729 . . . . . . . . . . . . . . . . . 80 mA
Continuous Current D, ADG728 . . . . . . . . . . . . . . . . 120 mA
Operating Temperature Range
Industrial (B Version) . . . . . . . . . . . . . . . . –40°C to +85°C
Storage Temperature Range . . . . . . . . . . . . –65°C to +150°C
Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . 150°C
TSSOP Package
θJA Thermal Impedance . . . . . . . . . . . . . . . . . . . 150.4°C/W
θJC Thermal Impedance . . . . . . . . . . . . . . . . . . . . 27.6°C/W
Lead Temperature, Soldering . . . . . As per JEDEC J-STD-020
NOTES
1
Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those listed in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability. Only one absolute
maximum rating may be applied at any one time.
2
Overvoltages at IN, S or D will be clamped by internal diodes. Current should be
limited to the maximum ratings given.
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection.
Although the ADG728/ADG729 features proprietary ESD protection circuitry, permanent damage
may occur on devices subjected to high-energy electrostatic discharges. Therefore, proper ESD
precautions are recommended to avoid performance degradation or loss of functionality.
WARNING!
ESD SENSITIVE DEVICE
TERMINOLOGY
VDD
Most Positive Power Supply Potential.
CD, CS (ON)
“ON” Switch Capacitance. Measured with reference to ground.
IDD
Positive Supply Current.
GND
Ground (0 V) Reference.
CIN
Digital Input Capacitance.
S
Source Terminal. May be an input or output.
tON
D
Drain Terminal. May be an input or output.
Delay time between the 50% and 90% points
of the STOP condition and the switch “ON”
condition.
VD (VS)
Analog Voltage on Terminals D, S.
tOFF
RON
Ohmic Resistance between D and S.
∆RON
On Resistance Match Between any Two Channels, i.e., RONmax – RONmin.
Delay time between the 50% and 90% points
of the STOP condition and the switch “OFF”
condition.
tD
“OFF” time measured between the 80% points of
both switches when switching from one switch to
another.
Charge
Injection
A measure of the glitch impulse transferred from
the digital input to the analog output during
switching.
Off Isolation
A measure of unwanted signal coupling through
an “OFF” switch.
Crosstalk
A measure of unwanted signal which is coupled
through from one channel to another as a result
of parasitic capacitance.
Bandwidth
The frequency at which the output is attenuated
by 3 dBs.
RFLAT(ON)
Flatness is defined as the difference between the
maximum and minimum value of on resistance
as measured over the specified analog signal range.
IS (OFF)
Source Leakage Current with the Switch “OFF.”
ID (OFF)
Drain Leakage Current with the Switch “OFF.”
ID, IS (ON)
Channel Leakage Current with the Switch “ON.”
VINL
Maximum Input Voltage for Logic “0.”
VINH
Minimum Input Voltage for Logic “1.”
IINL (IINH)
Input Current of the Digital Input.
CS (OFF)
“OFF” Switch Source Capacitance. Measured
with reference to ground.
CD (OFF)
“OFF” Switch Drain Capacitance. Measured
with reference to ground.
On Response The frequency response of the “ON” switch.
Insertion
Loss
–6–
The loss due to the ON resistance of the switch.
REV. C
Typical Performance Characteristics–ADG728/ADG729
8
8
ON RESISTANCE – ⍀
VDD = 3.3V
5
4
VDD = 4.5V
VDD = 5.5V
3
2
1
5
+25ⴗC
+85ⴗC
3
2
–40ⴗC
1
0
1
2
3
4
5
0
VD OR VS – DRAIN OR SOURCE VOLTAGE – V
Figure 3. On Resistance as a Function
of VD (VS) for Different Temperatures,
Single Supply
VDD = 5V
VSS = 0V
TA = 25ⴗC
0.08
CURRENT – nA
0.00
IS (OFF)
–0.04
4
–40ⴗC
3
+25ⴗC
2
Figure 4. On Resistance as a Function
of VD (VS) for Different Temperatures,
Single Supply
0.35
VDD = 3V
VSS = 0V
TA = 25ⴗC
0.08
ID (ON)
0.04
+85ⴗC
5
0
0.5
1.0
1.5
2.0
2.5
3.0
0
VD OR VS – DRAIN OR SOURCE VOLTAGE – V
0.12
0.12
6
1
0
1
0
2
3
4
5
VD OR VS – DRAIN OR SOURCE VOLTAGE – V
Figure 2. On Resistance as a Function
of VD (VS) for Single Supply
CURRENT – nA
6
4
VDD = 3V
VSS = 0V
7
0.25
ID (ON)
0.04
0.00
IS (OFF)
–0.04
VDD = 5V
VSS = 0V
0.30
CURRENT – nA
ON RESISTANCE – ⍀
7
VDD = 2.7V
6
8
VDD = 5V
VSS = 0V
ON RESISTANCE – ⍀
TA = 25ⴗC
VSS = 0V
7
ID (OFF)
0.20
0.15
ID (OFF)
0.10
ID (ON)
0.05
ID (OFF)
–0.08
–0.08
0.00
IS (OFF)
–0.12
–0.12
0
1
2
3
VD (VS) – Volts
4
5
Figure 5. Leakage Currents as a Function of VD (VS)
0
0.5
1.0
1.5
2.0
VD (VS) – Volts
2.5
3.0
Figure 6. Leakage Currents as a Function of VD (VS)
–0.05
15
VDD = 5V
VSS = 0V
0.10
ID (OFF)
100␮
0
QINJ – pC
CURRENT – A
CURRENT – nA
0.25
0.15
VDD = 5V
10␮
–20
–30
0.00
IS (OFF)
25
35
45
55
65
TEMPERATURE – ⴗC
ID (ON)
75
85
Figure 8. Leakage Currents as a Function of Temperature
REV. C
VDD = 3V
VSS = 0V
–10
VDD = 3V
0.05
–0.05
15
85
TA = 25ⴗC
10
0.20
75
20
TA = 25ⴗC
VDD = 3V
VSS = 0V
0.30
35
45
55
65
TEMPERATURE – ⴗC
Figure 7. Leakage Currents as a
Function of Temperature
1m
0.35
25
1␮
10k
100k
FREQUENCY – Hz
1M
Figure 9. Input Current vs. Switching Frequency
–7–
–40
0
1
2
3
VOLTAGE – Volts
4
Figure 10. Charge Injection vs.
Source Voltage
5
ADG728/ADG729
140
–20
100
80
TON, VDD = 5V
TOFF, VDD = 5V
60
ATTENUATION – dB
TOFF, VDD = 3V
120
VDD = 5V
TA = 25ⴗC
–20
ATTENUATION – dB
TON, VDD = 3V
TIME – ns
0
0
160
–40
–60
–80
VDD = 5V
TA = 25ⴗC
–40
–60
–80
40
–100
–100
20
0
–40
–20
0
20
40
60
TEMPERATURE – ⴗC
80
Figure 11. TON /TOFF Times vs.
Temperature
–120
30k
100k
1M
10M
FREQUENCY – Hz
100M
Figure 12. Off Isolation vs. Frequency
–120
30k
100k
1M
10M
FREQUENCY – Hz
100M
Figure 13. Crosstalk vs. Frequency
0
ATTENUATION – dB
VDD = 5V
TA = 25ⴗC
–5
ADG728
ADG729
–10
–15
–20
30k
100k
1M
10M
FREQUENCY – Hz
100M
Figure 14. On Response vs.
Frequency
–8–
REV. C
ADG728/ADG729
GENERAL DESCRIPTION
The ADG728 and ADG729 are serially controlled, 8-channel
and dual 4-channel matrix switches respectively. While providing the normal multiplexing and demultiplexing functions, these
devices also provide the user with more flexibility as to where
their signal may be routed. Each bit of the serial word corresponds to one switch of the device. A Logic 1 in the particular
bit position turns on the switch, while a Logic 0 turns the switch
off. Because each switch is independently controlled by an individual bit, this provides the option of having any, all, or none of
the switches ON. This feature may be particularly useful in the
demultiplexing application where the user may wish to direct
one signal from the drain to a number of outputs (sources). Care
must be taken, however, in the multiplexing situation where a
number of inputs may be shorted together (separated only by
the small on resistance of the switch).
The slave whose address corresponds to the transmitted
address responds by pulling the SDA line low during the
ninth clock pulse (this is termed the Acknowledge bit). At
this stage, all other devices on the bus remain idle while the
selected device waits for data to be written to or read from its
serial register. If the R/W bit is high, the master will read
from the slave device. However, if the R/W bit is low, the
master will write to the slave device.
2. Data is transmitted over the serial bus in sequences of nine
clock pulses (eight data bits followed by an acknowledge bit).
The transitions on the SDA line must occur during the low
period of SCL and remain stable during the high period of
SCL.
When changing the switch conditions, a new 8-bit word is written to the input shift register. Some of the bits may be the same
as the previous write cycle, as the user may not wish to change
the state of some switches. In order to minimize glitches on the
output of these switches, the part cleverly compares the state of
switches from the previous write cycle. If the switch is already
in the ON condition, and is required to stay ON, there will be
minimal glitches on the output of the switch.
3. When all data bits have been read or written, a STOP condition
is established by the master. A STOP condition is defined as
a low-to-high transition on the SDA line while SCL is high.
In Write mode, the master will pull the SDA line high during
the 10th clock pulse to establish a STOP condition. In Read
mode, the master will issue a No Acknowledge for the ninth
clock pulse (i.e., the SDA line remains high). The master will
then bring the SDA line low before the tenth clock pulse and
then high during the tenth clock pulse to establish a STOP
condition.
POWER-ON RESET
See Figures 18 to 21 below for a graphical explanation of the
serial interface.
On power-up of the device, all switches will be in the OFF condition and the internal shift register is filled with zeros and will
remain so until a valid write takes place.
SERIAL INTERFACE
2-Wire Serial Bus
The ADG728/ADG729 are controlled via an I2C compatible
serial bus. These parts are connected to this bus as a slave device
(no clock is generated by the multiplexer).
The ADG728/ADG729 have different 7-bit slave addresses.
The five MSBs of the ADG728 are 10011, while the MSBs of
the ADG729 are 10001 and the two LSBs are determined by
the state of the A0 and A1 pins.
The 2-wire serial bus protocol operates as follows:
1. The master initiates data transfer by establishing a START
condition which is when a high-to-low transition on the SDA
line occurs while SCL is high. The following byte is the
address byte, which consists of the 7-bit slave address followed by a R/W bit (this bit determines whether data will be
read from or written to the slave device).
A repeated write function gives the user flexibility to update the
matrix switch a number of times after addressing the part only
once. During the write cycle, each data byte will update the configuration of the switches. For example, after the matrix switch
has acknowledged its address byte, and receives one data byte,
the switches will update after the data byte, if another data byte
is written to the matrix switch while it is still the addressed slave
device, this data byte will also cause an switch configuration
update. Repeat read of the matrix switch is also allowed.
INPUT SHIFT REGISTER
The input shift register is eight bits wide. Figure 15 illustrates
the contents of the input shift register. Data is loaded into the
device as an 8-bit word under the control of a serial clock input,
SCL. The timing diagram for this operation is shown in Figure 1.
The 8-bit word consists of eight data bits each controlling one
switch. MSB (Bit 7) is loaded first.
DB0 (LSB)
DB7 (MSB)
S8
S7
S6
S5
S4
S3
S2
S1
DATA BITS
Figure 15. ADG728/ADG729 Input Shift Register Contents
REV. C
–9–
ADG728/ADG729
WRITE OPERATION
When writing to the ADG728/ADG729, the user must begin
with an address byte and R/W bit, after which the switch will
acknowledge that it is prepared to receive data by pulling SDA
low. This address byte is followed by the 8-bit word. The write
operations for each matrix switch are shown in the figures below.
SCL
1
SDA
0
START
COND
BY
MASTER
0
1
1
A1
A0
R/W
S8
S7
S6
ACK
BY
ADG728
ADDRESS BYTE
S5
S4
S3
S2
S1
STOP
ACK
COND
BY
BY
ADG728
MASTER
DATA BYTE
Figure 16. ADG728 Write Sequence
SCL
1
SDA
0
START
COND
BY
MASTER
0
0
1
A1
A0
R/W
S8
S7
S6
ACK
BY
ADG729
ADDRESS BYTE
S5
S4
S3
S2
S1
STOP
ACK
COND
BY
BY
ADG729
MASTER
DATA BYTE
Figure 17. ADG729 Write Sequence
READ OPERATION
When reading data back from the ADG728/ADG729, the user must begin with an address byte and R/W bit, after which the matrix switch will acknowledge that it is prepared to transmit data by pulling SDA low. The readback operation is a single byte that
consists of the eight data bits in the input register. The read operations for each part are shown in Figures 18 and 19.
SCL
1
SDA
0
START
COND
BY
MASTER
0
1
1
A1
A0
R/W
S8
S7
S6
ACK
BY
ADG728
ADDRESS BYTE
S5
S4
S3
S2
S1
NO ACK STOP
COND
BY
BY
MASTER
MASTER
DATA BYTE
Figure 18. ADG728 Readback Sequence
SCL
1
SDA
START
COND
BY
MASTER
0
0
0
ADDRESS BYTE
1
A1
A0
R/W
S8
ACK
BY
ADG729
S7
S6
S5
S4
DATA BYTE
S3
S2
S1
NO ACK STOP
COND
BY
BY
MASTER
MASTER
Figure 19. ADG729 Readback Sequence
–10–
REV. C
ADG728/ADG729
MULTIPLE DEVICES ON ONE BUS
Figure 20 shows four ADG728s devices on the same serial bus.
Each has a different slave address since the state of their A0 and
A1 pins is different. This allows each Matrix Switch to be written to or read from independently. Because the ADG729 has a
different address to the ADG728, it would be possible for four
of each of these devices to be connected to the same bus.
+5V
RP
RP
SDA
MASTER
SCL
VDD
VDD
SDA
SCL
SDA
A1
SCL
A1
A0
SCL
SDA
A1
A0
ADG728
VDD
SDA
A0
ADG728
SCL
A1
A0
ADG728
ADG728
Figure 20. Multiple ADG728s on the Same Bus
TEST CIRCUITS
IDS
VDD
VDD
V1
S1
S2
S
D
D
ID (OFF)
A
S8
VD
GND
VS
VS
RON = V1/IDS
Test Circuit 1. On Resistance
Test Circuit 3. IS (OFF)
VDD
VDD
VDD
VDD
IS (OFF)
S1
S1
A
D
S8
S2
VS
ID (ON)
A
VD
D
S8
VD
GND
VS
GND
Test Circuit 2. ID (OFF)
Test Circuit 4. ID (ON)
VDD
VDD
SCL
50%
50%
ADG728*
S1
VS1
S2 THRU S7
S8
D
GND
VS1
VS8
RL
300⍀
90%
CL
35pF
VOUT
VOUT
VS1 = VS8
VOUT
80%
80%
90%
tOPEN
* SIMILAR CONNECTION FOR ADG729
tOFF
tON
Test Circuit 5. Switching Times and Break-Before-Make Times
REV. C
–11–
ADG728/ADG729
VDD
VDD
ADG728*
SWITCH ON
RS
VS
D
S
CL
1nF
INPUT LOGIC
VOUT
⌬VOUT
SWITCH OFF
QINJ = CL x ⌬VOUT
GND
SDA SCL
* SIMILAR CONNECTION FOR ADG729
Test Circuit 6. Charge Injection
VDD
VDD
VDD
VDD
ADG728*
50⍀
S1
D
RL
S2
VS
S8
S1
S8
VS
ADG728*
VOUT
50⍀
D
GND
GND
RL
VOUT
50⍀
* SIMILAR CONNECTION FOR ADG729
*SIMILAR CONNECTION FOR ADG729
CHANNEL-TO-CHANNEL CROSSTALK = 20LOG10(VOUT/VS)
S1 IS SWITCHED OFF FOR OFF ISOLATION MEASUREMENTS AND ON FOR BANDWIDTH MEASUREMENTS
OFF ISOLATION = 20LOG10(VOUT/VS)
Test Circuit 7. Channel-to-Channel Crosstalk
INSERTION LOSS = 20LOG10
VOUT WITH SWITCH
VOUT WITHOUT SWITCH
Test Circuit 8. Off Isolation and Bandwidth
–12–
REV. C
ADG728/ADG729
OUTLINE DIMENSIONS
5.10
5.00
4.90
16
9
4.50
4.40
4.30
6.40
BSC
1
8
PIN 1
1.20
MAX
0.15
0.05
0.20
0.09
0.30
0.19
0.65
BSC
COPLANARITY
0.10
8°
0°
SEATING
PLANE
0.75
0.60
0.45
COMPLIANT TO JEDEC STANDARDS MO-153-AB
Figure 1. 16-Lead Thin Shrink Small Outline Package [TSSOP]
(RU-16)
Dimensions shown in millimeters
ORDERING GUIDE
Model 1, 2
ADG728BRU
ADG728BRU-REEL
ADG728BRU-REEL7
ADG728BRUZ
ADG728BRUZ-REEL
ADG728BRUZ-REEL7
ADG728WBRUZ-REEL7
ADG729BRU
ADG729BRU-REEL
ADG729BRU-REEL7
ADG729BRUZ
ADG729BRUZ-REEL7
1
2
Temperature Range
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
Package Description
16-Lead Thin Shrink Small Outline Package [TSSOP]
16-Lead Thin Shrink Small Outline Package [TSSOP]
16-Lead Thin Shrink Small Outline Package [TSSOP]
16-Lead Thin Shrink Small Outline Package [TSSOP]
16-Lead Thin Shrink Small Outline Package [TSSOP]
16-Lead Thin Shrink Small Outline Package [TSSOP]
16-Lead Thin Shrink Small Outline Package [TSSOP]
16-Lead Thin Shrink Small Outline Package [TSSOP]
16-Lead Thin Shrink Small Outline Package [TSSOP]
16-Lead Thin Shrink Small Outline Package [TSSOP]
16-Lead Thin Shrink Small Outline Package [TSSOP]
16-Lead Thin Shrink Small Outline Package [TSSOP]
Package Option
RU-16
RU-16
RU-16
RU-16
RU-16
RU-16
RU-16
RU-16
RU-16
RU-16
RU-16
RU-16
Z = RoHS Compliant Part.
W = Qualified for Automotive Applications.
AUTOMOTIVE PRODUCTS
The ADG728W model is available with controlled manufacturing to support the quality and reliability requirements of automotive
applications. Note that this automotive model may have specifications that differ from the commercial models; therefore, designers
should review the Specifications section of this data sheet carefully. Only the automotive grade product shown is available for use in
automotive applications. Contact your local Analog Devices account representative for specific product ordering information and to
obtain the specific Automotive Reliability reports for this model.
REVISION HISTORY
6/12—Rev. B to Rev. C
Changes to Timing Characteristics Section .................................. 4
10/11—Rev. A to Rev. B
Change to Features Section ..............................................................1
Changes to Absolute Maximum Ratings Section ..........................6
Updated Outline Dimensions ....................................................... 13
Changes to Ordering Guide .......................................................... 13
Added Automotive Products Section .......................................... 13
©2012 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D01002-0-6/12(C)
REV. C
–13–