rev** 23533 15.9mm [0.625"] 24.8mm [0.975"] Top View 27.6mm [1.085"] Bottom View 20.3mm [0.799"] CY3250-23533 Description: POD 56 pin QFN OCD with Hirose cable connector (P/N: DF12-5.0-20DP-0.5V-81) with retension mechanism included. Compatible with: SF-QFN32A-L-02, QFN foot, 32 pin, 0.5mm pitch, 5mm body XT-PSoC-15-20H-10-01 CY8C23033-24PVXI threaded inserts for mounting hardware Side View UGA Male pin shroud 1 Page:____of 2 EA-8C23533-Q32-01 Drawing © 2007 IRONWOOD ELECTRONICS, INC. Tele: (800) 404-0204 www.ironwoodelectronics.com Status: Released 3:1 Scale:___ Rev: A Drawing: J. Glab Date: 11/27/07 File: EA-8C23533-Q32-01 Dwg Modified: Tolerances: diameters ±0.03mm [±0.001”], PCB perimeters ±0.13mm [±0.005”], PCB thicknesses ±0.18mm [±0.007"], pitches (from true position) ±0.08mm [±0.003"], all other tolerances ±0.13mm [±0.005”] unless stated otherwise. Materials and specifications are subject to change without notice. Strain Relief Hardware mounting directions (627", 0.488") If the target board can be designed to accomodate the strain relief hardware, layout the PCB with the pattern shown on the right. The layout shows the location of non-plated holes through the board relative to the QFN land pattern. If holes can not be added to the target board, the screws can be used as standoffs and sit on the top surface of the target PCB. (0.369", 0.398") (-0.283", 0.398") QFN outline (0.00", 0.00") 19.37mm [0.763"] 0.5mm McMaster/Carr 91185A558 24.77mm [0.975"] Pin 1 Flex Cable 8.49mm sq. [0.334"] To ICE Pod 5.55mm [0.218"] Shroud ouline (keep away area) Pad size: 0.3mmX0.78mm [0.012" X 0.031"] E-pad 3.2X3.2mm 13.25mm [0.521"] (-0.283", -0.398") 7.91mm [0.311"] (0.369", -0.399") Ø 1.78mm [Ø 0.070"] ±0.005" (-0.627", -0.488") Pod outline 5.31mm [0.209"] 27.57mm [1.085"] 4.91mm [0.193"] 0.48mm [0.019"] All component heights ±0.020" Top View: Target Board component layout notes: 1) Do not place components within the shroud outline unless they have a 0.035" height or less off the target board and are outside the QFN package outline 2) All components under the POD outline must have a 0.190" height or or less from the top of target board to avoid components on the bottom of the POD board. Side view: CY3250-23533QFN Pod on QFN32 foot EA-8C23533-Q32-01 Drawing © 2007 IRONWOOD ELECTRONICS, INC. Tele: (800) 404-0204 www.ironwoodelectronics.com 2 Page:____of 2 Status: Released 4:1 Scale:___ Rev: A Drawing: J. Glab Date: 11/27/07 File: EA-8C23533-Q32-01 Dwg Modified: Tolerances: diameters ±0.03mm [±0.001”], PCB perimeters ±0.13mm [±0.005”], PCB thicknesses ±0.18mm [±0.007"], pitches (from true position) ±0.08mm [±0.003"], all other tolerances ±0.13mm [±0.005”] unless stated otherwise. Materials and specifications are subject to change without notice.