MURATA DLW21HN121HQ2L

Noise Suppression Products/EMI Suppression Filters > Common Mode Choke Coil > Wire Wound Type
Data Sheet
1
Common Mode Choke Coil Wire Wound Type
DLW21H Series (0805 Size)
c Dimensions
c Impedance-Frequency Characteristics (Main Items)
DLW21HN181SQ2
(0.17)
DLW21HN121SQ2
2.0±0.2
(0.45)
1.2±0.2
(0.45)
DLW21HN900SQ2
100
DLW21HN670SQ2
10
(2)
DLW21HN181SQ2
(0.4)
(1)
Common mode
1000
Impedance (Ω)
0.9±0.1
10000
DLW21HN121SQ2
1
DLW21HN900SQ2
(0.4)
Differential mode
(4)
DLW21HN670SQ2
0.1
: Electrode
1
(3)
10
100
1000
Frequency (MHz)
(in mm)
c Impedance-Frequency Characteristics (Main Items)
c Equivalent Circuit
10000
Common mode
Impedance (Ω)
1000
DLW21HN121HQ2
DLW21HN900HQ2
100
(1)
(2)
(4)
(3)
DLW21HN670HQ2
10
1
DLW21HN121HQ2
DLW21HN900HQ2
DLW21HN670HQ2
0.1
1
10
Differential mode
No polarity.
100
1000
Frequency (MHz)
c Differential Mode Transmission Characteristics (Typ.)
0
DLW21HN670HQ2
DLW21HN900HQ2
DLW21HN121HQ2
Insertion Loss (dB)
2
c Packaging
Code
Packaging
Minimum Quantity
L
180mm Embossed Tape
3000
B
Bulk(Bag)
500
4
6
8
10
1
10
100
Frequency (MHz)
1000
10000
Continued on the following page.
oThis data sheet is applied for CHIP COMMON MODE CHOKE COIL used for General Electronics equipment for your design.
!Note:
1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it
may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering.
2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product
specifications or transact the approval sheet for product specifications before ordering.
2013.3.7
http://www.murata.com/
Noise Suppression Products/EMI Suppression Filters > Common Mode Choke Coil > Wire Wound Type
Data Sheet
2
Continued from the preceding page.
c Rated Value (p: packaging code)
Operating
Temperature Range
Part Number
Common Mode Impedance
(at 100MHz/20°C)
DLW21HN670SQ2p
67ohm ±25%
330mA
50Vdc
10M ohm
125Vdc
0.35ohm max.
DLW21HN900SQ2p
90ohm ±25%
330mA
50Vdc
10M ohm
125Vdc
0.35ohm max.
-40 to +85°C
DLW21HN121SQ2p
120ohm ±25%
280mA
50Vdc
10M ohm
125Vdc
0.45ohm max.
-40 to +85°C
DLW21HN181SQ2p
180ohm ±25%
250mA
50Vdc
10M ohm
125Vdc
0.50ohm max.
-40 to +85°C
DLW21HN670HQ2p
67ohm ±25%
240mA
20Vdc
10M ohm
50Vdc
0.49ohm max.
-40 to +85°C
DLW21HN900HQ2p
90ohm ±25%
220mA
20Vdc
10M ohm
50Vdc
0.59ohm max.
-40 to +85°C
DLW21HN121HQ2p
120ohm ±25%
200mA
20Vdc
10M ohm
50Vdc
0.68ohm max.
-40 to +85°C
Rated Current Rated Voltage Insulation Resistance (min.)
Withstand Voltage DC Resistance
-40 to +85°C
Number of Circuit: 1
c !Caution/Notice
!Caution (Rating)
Do not use products beyond the rated current and
rated voltage as this may create excessive heat
and deteriorate the insulation resistance.
Notice
Solderability of Tin plating termination chip might be
deteriorated when low temperature soldering profile
where peak solder temperature is below the Tin melting
point is used. Please confirm the solderability of Tin
plating termination chip before use.
oThis data sheet is applied for CHIP COMMON MODE CHOKE COIL used for General Electronics equipment for your design.
!Note:
1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it
may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering.
2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product
specifications or transact the approval sheet for product specifications before ordering.
2013.3.7
http://www.murata.com/