HITACHI HD44780UA02TF

HD44780U (LCD-II)
(Dot Matrix Liquid Crystal Display Controller/Driver)
Description
The HD44780U dot-matrix liquid crystal display controller and driver LSI displays alphanumerics,
Japanese kana characters, and symbols. It can be configured to drive a dot-matrix liquid crystal display
under the control of a 4- or 8-bit microprocessor. Since all the functions such as display RAM, character
generator, and liquid crystal driver, required for driving a dot-matrix liquid crystal display are internally
provided on one chip, a minimal system can be interfaced with this controller/driver.
A single HD44780U can display up to one 8-character line or two 8-character lines.
The HD44780U has pin function compatibility with the HD44780S which allows the user to easily replace
an LCD-II with an HD44780U. The HD44780U character generator ROM is extended to generate 208 5 ×
8 dot character fonts and 32 5 × 10 dot character fonts for a total of 240 different character fonts.
The low power supply (2.7V to 5.5V) of the HD44780U is suitable for any portable battery-driven product
requiring low power dissipation.
Features
• 5 × 8 and 5 × 10 dot matrix possible
• Low power operation support:
 2.7 to 5.5V
• Wide range of liquid crystal display driver power
 3.0 to 11V
• Liquid crystal drive waveform
 A (One line frequency AC waveform)
• Correspond to high speed MPU bus interface
 2 MHz (when VCC = 5V)
• 4-bit or 8-bit MPU interface enabled
• 80 × 8-bit display RAM (80 characters max.)
• 9,920-bit character generator ROM for a total of 240 character fonts
 208 character fonts (5 × 8 dot)
 32 character fonts (5 × 10 dot)
1
HD44780U
• 64 × 8-bit character generator RAM
 8 character fonts (5 × 8 dot)
 4 character fonts (5 × 10 dot)
• 16-common × 40-segment liquid crystal display driver
• Programmable duty cycles
 1/8 for one line of 5 × 8 dots with cursor
 1/11 for one line of 5 × 10 dots with cursor
 1/16 for two lines of 5 × 8 dots with cursor
• Wide range of instruction functions:
 Display clear, cursor home, display on/off, cursor on/off, display character blink, cursor shift,
display shift
• Pin function compatibility with HD44780S
• Automatic reset circuit that initializes the controller/driver after power on
• Internal oscillator with external resistors
• Low power consumption
Ordering Information
Type No.
Package
CGROM
HD44780UA00FS
HCD44780UA00
HD44780UA00TF
HD44780UA02FS
HCD44780UA02
HD44780UA02TF
FP-80B
Chip
TFP-80F
FP-80B
Chip
TFP-80F
Japanese standard font
HD44780UBxxFS
HCD44780UBxx
HD44780UBxxTF
FP-80B
Chip
TFP-80F
Custom font
Note: xx: ROM code No.
2
European standard font
HD44780U
HD44780U Block Diagram
OSC1 OSC2
M
Reset
circuit
ACL
Timing
generator
CPG
8
RS
R/W
E
Instruction
register (IR)
7
Input/
output
buffer
8
16-bit
shift
register
Common
signal
driver
40-bit
latch
circuit
Segment
signal
driver
7
40-bit
shift
register
8
7
DB4 to
DB7
D
Display
data RAM
(DDRAM)
80 × 8 bits
Instruction
decoder
MPU
interface
Address
counter
DB0 to
DB3
CL1
CL2
SEG1 to
SEG40
7
Data
register
(DR)
8
40
8
8
LCD drive
voltage
selector
Busy
flag
GND
COM1 to
COM16
Character
generator
ROM
(CGROM)
9,920 bits
Character
generator
RAM
(CGRAM)
64 bytes
5
Cursor
and
blink
controller
5
Parallel/serial converter
and
attribute circuit
VCC
V1
V2
V3
V4
V5
3
HD44780U
65
66
67
68
69
70
71
72
73
74
75
76
77
78
1
64
2
63
3
62
4
61
5
60
6
59
7
58
8
57
9
56
10
55
11
54
FP-80B
(Top view)
12
13
53
52
40
39
38
OSC2
V1
V2
V3
V4
V5
CL1
CL2
VCC
M
D
RS
R/W
E
DB0
DB1
37
41
36
42
24
35
43
23
34
44
22
33
45
21
32
46
20
31
47
19
30
48
18
29
49
17
28
50
16
27
51
15
26
14
25
SEG22
SEG21
SEG20
SEG19
SEG18
SEG17
SEG16
SEG15
SEG14
SEG13
SEG12
SEG11
SEG10
SEG9
SEG8
SEG7
SEG6
SEG5
SEG4
SEG3
SEG2
SEG1
GND
OSC1
79
80
SEG23
SEG24
SEG25
SEG26
SEG27
SEG28
SEG29
SEG30
SEG31
SEG32
SEG33
SEG34
SEG35
SEG36
SEG37
SEG38
HD44780U Pin Arrangement (FP-80B)
4
SEG39
SEG40
COM16
COM15
COM14
COM13
COM12
COM11
COM10
COM9
COM8
COM7
COM6
COM5
COM4
COM3
COM2
COM1
DB7
DB6
DB5
DB4
DB3
DB2
HD44780U
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
1
60
2
59
3
58
4
57
5
56
6
55
7
54
8
53
9
52
TFP-80F
(Top view)
10
11
51
50
40
39
38
37
36
35
34
33
32
31
30
41
29
42
20
28
43
19
27
44
18
26
45
17
25
46
16
24
47
15
23
48
14
22
49
13
21
12
COM16
COM15
COM14
COM13
COM12
COM11
COM10
COM9
COM8
COM7
COM6
COM5
COM4
COM3
COM2
COM1
DB7
DB6
DB5
DB4
GND
OSC1
OSC2
V1
V2
V3
V4
V5
CL1
CL2
VCC
M
D
RS
R/W
E
DB0
DB1
DB2
DB3
SEG20
SEG19
SEG18
SEG17
SEG16
SEG15
SEG14
SEG13
SEG12
SEG11
SEG10
SEG9
SEG8
SEG7
SEG6
SEG5
SEG4
SEG3
SEG2
SEG1
79
80
SEG21
SEG22
SEG23
SEG24
SEG25
SEG26
SEG27
SEG28
SEG29
SEG30
SEG31
SEG32
SEG33
SEG34
SEG35
SEG36
SEG37
SEG38
SEG39
SEG40
HD44780U Pin Arrangement (TFP-80F)
5
HD44780U
HD44780U Pad Arrangement
Chip size:
4.90 × 4.90 mm2
Coordinate: Pad center (µm)
2
1
Origin:
Chip center
Pad size:
114 × 114 µm2
80
63
Y
Type code
HD44780U
23
42
X
6
HD44780U
HCD44780U Pad Location Coordinates
Pad No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
Function
SEG22
SEG21
SEG20
SEG19
SEG18
SEG17
SEG16
SEG15
SEG14
SEG13
SEG12
SEG11
SEG10
SEG9
SEG8
SEG7
SEG6
SEG5
SEG4
SEG3
SEG2
SEG1
GND
OSC1
OSC2
V1
V2
V3
V4
V5
CL1
CL2
VCC
M
D
RS
R/W
E
DB0
DB1
Coordinate
X (um)
Y (um)
–2100
2313
–2280
2313
–2313
2089
–2313
1833
–2313
1617
–2313
1401
–2313
1186
–2313
970
–2313
755
–2313
539
–2313
323
–2313
108
–2313
–108
–2313
–323
–2313
–539
–2313
–755
–2313
–970
–2313
–1186
–2313
–1401
–2313
–1617
–2313
–1833
–2313
–2073
–2280
–2290
–2080
–2290
–1749
–2290
–1550
–2290
–1268
–2290
–941
–2290
–623
–2290
–304
–2290
–48
–2290
142
–2290
309
–2290
475
–2290
665
–2290
832
–2290
1022
–2290
1204
–2290
1454
–2290
1684
–2290
Pad No.
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
Function
DB2
DB3
DB4
DB5
DB6
DB7
COM1
COM2
COM3
COM4
COM5
COM6
COM7
COM8
COM9
COM10
COM11
COM12
COM13
COM14
COM15
COM16
SEG40
SEG39
SEG38
SEG37
SEG36
SEG35
SEG34
SEG33
SEG32
SEG31
SEG30
SEG29
SEG28
SEG27
SEG26
SEG25
SEG24
SEG23
Coordinate
X (um)
Y (um)
2070
–2290
2260
–2290
2290
–2099
2290
–1883
2290
–1667
2290
–1452
2313
–1186
2313
–970
2313
–755
2313
–539
2313
–323
2313
–108
2313
108
2313
323
2313
539
2313
755
2313
970
2313
1186
2313
1401
2313
1617
2313
1833
2313
2095
2296
2313
2100
2313
1617
2313
1401
2313
1186
2313
970
2313
755
2313
539
2313
323
2313
108
2313
–108
2313
–323
2313
–539
2313
–755
2313
–970
2313
–1186
2313
–1401
2313
–1617
2313
7
HD44780U
Pin Functions
Signal
No. of
Lines
I/O
Device
Interfaced with
RS
1
I
MPU
Selects registers.
0: Instruction register (for write) Busy flag:
address counter (for read)
1: Data register (for write and read)
R/W
1
I
MPU
Selects read or write.
0: Write
1: Read
E
1
I
MPU
Starts data read/write.
DB4 to DB7
4
I/O
MPU
Four high order bidirectional tristate data bus
pins. Used for data transfer and receive between
the MPU and the HD44780U. DB7 can be used
as a busy flag.
DB0 to DB3
4
I/O
MPU
Four low order bidirectional tristate data bus pins.
Used for data transfer and receive between the
MPU and the HD44780U.
These pins are not used during 4-bit operation.
CL1
1
O
Extension driver
Clock to latch serial data D sent to the extension
driver
CL2
1
O
Extension driver
Clock to shift serial data D
M
1
O
Extension driver
Switch signal for converting the liquid crystal
drive waveform to AC
D
1
O
Extension driver
Character pattern data corresponding to each
segment signal
COM1 to COM16 16
O
LCD
Common signals that are not used are changed
to non-selection waveforms. COM9 to COM16
are non-selection waveforms at 1/8 duty factor
and COM12 to COM16 are non-selection
waveforms at 1/11 duty factor.
SEG1 to SEG40 40
O
LCD
Segment signals
V1 to V5
5
—
Power supply
Power supply for LCD drive
VCC –V5 = 11 V (max)
VCC, GND
2
—
Power supply
VCC: 2.7V to 5.5V, GND: 0V
OSC1, OSC2
2
—
Oscillation
resistor clock
When crystal oscillation is performed, a resistor
must be connected externally. When the pin input
is an external clock, it must be input to OSC1.
8
Function
HD44780U
Function Description
Registers
The HD44780U has two 8-bit registers, an instruction register (IR) and a data register (DR).
The IR stores instruction codes, such as display clear and cursor shift, and address information for display
data RAM (DDRAM) and character generator RAM (CGRAM). The IR can only be written from the MPU.
The DR temporarily stores data to be written into DDRAM or CGRAM and temporarily stores data to be
read from DDRAM or CGRAM. Data written into the DR from the MPU is automatically written into
DDRAM or CGRAM by an internal operation. The DR is also used for data storage when reading data
from DDRAM or CGRAM. When address information is written into the IR, data is read and then stored
into the DR from DDRAM or CGRAM by an internal operation. Data transfer between the MPU is then
completed when the MPU reads the DR. After the read, data in DDRAM or CGRAM at the next address is
sent to the DR for the next read from the MPU. By the register selector (RS) signal, these two registers can
be selected (Table 1).
Busy Flag (BF)
When the busy flag is 1, the HD44780U is in the internal operation mode, and the next instruction will not
be accepted. When RS = 0 and R/W = 1 (Table 1), the busy flag is output to DB7. The next instruction
must be written after ensuring that the busy flag is 0.
Address Counter (AC)
The address counter (AC) assigns addresses to both DDRAM and CGRAM. When an address of an
instruction is written into the IR, the address information is sent from the IR to the AC. Selection of either
DDRAM or CGRAM is also determined concurrently by the instruction.
After writing into (reading from) DDRAM or CGRAM, the AC is automatically incremented by 1
(decremented by 1). The AC contents are then output to DB0 to DB6 when RS = 0 and R/W = 1 (Table 1).
Table 1
Register Selection
RS
R/W
Operation
0
0
IR write as an internal operation (display clear, etc.)
0
1
Read busy flag (DB7) and address counter (DB0 to DB6)
1
0
DR write as an internal operation (DR to DDRAM or CGRAM)
1
1
DR read as an internal operation (DDRAM or CGRAM to DR)
9
HD44780U
Display Data RAM (DDRAM)
Display data RAM (DDRAM) stores display data represented in 8-bit character codes. Its extended
capacity is 80 × 8 bits, or 80 characters. The area in display data RAM (DDRAM) that is not used for
display can be used as general data RAM. See Figure 1 for the relationships between DDRAM addresses
and positions on the liquid crystal display.
The DDRAM address (ADD ) is set in the address counter (AC) as hexadecimal.
• 1-line display (N = 0) (Figure 2)
 When there are fewer than 80 display characters, the display begins at the head position. For
example, if using only the HD44780, 8 characters are displayed. See Figure 3.
When the display shift operation is performed, the DDRAM address shifts. See Figure 3.
High order
bits
Low order
bits
Example: DDRAM address 4E
AC
(hexadecimal) AC6 AC5 AC4 AC3 AC2 AC1 AC0
1
0
0
1
1
Figure 1 DDRAM Address
Display position
(digit)
1
2
3
DDRAM
00 01
address
(hexadecimal)
4
02
5
79
..................
03 04
Figure 2 1-Line Display
Display
position
1
2
3
4
5
6
7
8
DDRAM
address
00 01 02 03 04 05 06 07
For
shift left
01 02 03 04 05 06 07 08
For
shift right 4F 00 01 02 03 04 05 06
Figure 3 1-Line by 8-Character Display Example
10
80
4E 4F
1
0
HD44780U
• 2-line display (N = 1) (Figure 4)
 Case 1: When the number of display characters is less than 40 × 2 lines, the two lines are displayed
from the head. Note that the first line end address and the second line start address are not
consecutive. For example, when just the HD44780 is used, 8 characters × 2 lines are displayed. See
Figure 5.
When display shift operation is performed, the DDRAM address shifts. See Figure 5.
Display
position
1
2
3
00 01
DDRAM
address
(hexadecimal) 40 41
4
5
39
40
02
03 04
..................
26 27
42
43 44
..................
66 67
Figure 4 2-Line Display
Display
position
1
2
3
4
5
6
7
8
DDRAM
address
00 01 02 03 04 05 06 07
For
shift left
01 02 03 04 05 06 07 08
40 41 42 43 44 45 46 47
41 42 43 44 45 46 47 48
27 00 01 02 03 04 05 06
For
shift right
67 40 41 42 43 44 45 46
Figure 5 2-Line by 8-Character Display Example
11
HD44780U
 Case 2: For a 16-character × 2-line display, the HD44780 can be extended using one 40-output
extension driver. See Figure 6.
When display shift operation is performed, the DDRAM address shifts. See Figure 6.
Display
position
DDRAM
address
1
2
3
4
5
6
7
8
9 10 11 12 13 14 15 16
00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F
40 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4E 4F
HD44780U display
For
shift left
Extension driver
display
01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10
41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4E 4F 50
27 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E
For
shift right
67 40 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4E
Figure 6 2-Line by 16-Character Display Example
12
HD44780U
Character Generator ROM (CGROM)
The character generator ROM generates 5 × 8 dot or 5 × 10 dot character patterns from 8-bit character
codes (Table 4). It can generate 208 5 × 8 dot character patterns and 32 5 × 10 dot character patterns. Userdefined character patterns are also available by mask-programmed ROM.
Character Generator RAM (CGRAM)
In the character generator RAM, the user can rewrite character patterns by program. For 5 × 8 dots, eight
character patterns can be written, and for 5 × 10 dots, four character patterns can be written.
Write into DDRAM the character codes at the addresses shown as the left column of Table 4 to show the
character patterns stored in CGRAM.
See Table 5 for the relationship between CGRAM addresses and data and display patterns.
Areas that are not used for display can be used as general data RAM.
Modifying Character Patterns
• Character pattern development procedure
The following operations correspond to the numbers listed in Figure 7:
1. Determine the correspondence between character codes and character patterns.
2. Create a listing indicating the correspondence between EPROM addresses and data.
3. Program the character patterns into the EPROM.
4. Send the EPROM to Hitachi.
5. Computer processing on the EPROM is performed at Hitachi to create a character pattern listing, which
is sent to the user.
6. If there are no problems within the character pattern listing, a trial LSI is created at Hitachi and samples
are sent to the user for evaluation. When it is confirmed by the user that the character patterns are
correctly written, mass production of the LSI proceeds at Hitachi.
13
HD44780U
Hitachi
User
Start
Computer
processing
Create character
pattern listing
5
Evaluate
character
patterns
No
Determine
character patterns
1
Create EPROM
address data listing
2
Write EPROM
3
EPROM → Hitachi
4
OK?
Yes
Art work
M/T
Masking
Trial
Sample
Sample
evaluation
OK?
6
No
Yes
Mass
production
Note: For a description of the numbers used in this figure, refer to the preceding page.
Figure 7 Character Pattern Development Procedure
14
HD44780U
• Programming character patterns
This section explains the correspondence between addresses and data used to program character patterns
in EPROM. The HD44780U character generator ROM can generate 208 5 × 8 dot character patterns and
32 5 × 10 dot character patterns for a total of 240 different character patterns.
 Character patterns
EPROM address data and character pattern data correspond with each other to form a 5 × 8 or 5 ×
10 dot character pattern (Tables 2 and 3).
Table 2
Example of Correspondence between EPROM Address Data and Character Pattern
(5 × 8 Dots)
Data
EPROM Address
LSB
A 1 1A 1 0 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 O 4 O3 O2 O1 O0
0
1
1
0
0
0
Character code
Notes: 1.
2.
3.
4.
5.
6.
1
0
0
0
0
0
1
0
0
0
0
0
0
0
1
1
0
0
0
0
0
0
1
0
1
0
1
1
0
0
0
1
1
1
1
0
0
1
0
1
0
0
1
0
0
0
1
0
0
0
1
0
1
0
1
1
0
1
1
0
1
1
1
1
0
0
1
1
1
0
0
0
0
0
1
0
0
0
0
0
0
0
0
1
0
0
1
0
0
0
0
0
1
0
1
0
0
0
0
0
0
1
0
1
1
0
0
0
0
0
1
1
0
0
0
0
0
0
0
1
1
0
1
0
0
0
0
0
1
1
1
0
0
0
0
0
0
1
1
1
1
0
0
0
0
0
Cursor position
Line
position
EPROM addresses A11 to A4 correspond to a character code.
EPROM addresses A3 to A0 specify a line position of the character pattern.
EPROM data O4 to O0 correspond to character pattern data.
EPROM data O5 to O7 must be specified as 0.
A lit display position (black) corresponds to a 1.
Line 9 and the following lines must be blanked with 0s for a 5 × 8 dot character fonts.
15
HD44780U
 Handling unused character patterns
1. EPROM data outside the character pattern area: Always input 0s.
2. EPROM data in CGRAM area: Always input 0s. (Input 0s to EPROM addresses 00H to FFH.)
3. EPROM data used when the user does not use any HD44780U character pattern: According to the user
application, handled in one of the two ways listed as follows.
a. When unused character patterns are not programmed: If an unused character code is written into
DDRAM, all its dots are lit. By not programing a character pattern, all of its bits become lit. (This is
due to the EPROM being filled with 1s after it is erased.)
b. When unused character patterns are programmed as 0s: Nothing is displayed even if unused
character codes are written into DDRAM. (This is equivalent to a space.)
Table 3
Example of Correspondence between EPROM Address Data and Character Pattern
(5 × 10 Dots)
EPROM Address
Data
LSB
A 1 1A 1 0 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 O 4 O3 O2 O1 O0
0
1
0
1
0
0
Character code
Notes: 1.
2.
3.
4.
5.
6.
16
1
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
1
0
0
1
1
0
1
0
0
1
1
1
0
0
1
1
0
1
0
0
1
0
0
0
1
0
1
0
1
1
0
0
0
1
0
1
1
0
0
1
1
1
1
0
1
1
1
0
0
0
0
1
1
0
0
0
0
0
0
0
1
1
0
0
1
0
0
0
0
1
1
0
1
0
0
0
0
0
0
1
0
1
1
0
0
0
0
0
1
1
0
0
0
0
0
0
0
1
1
0
1
0
0
0
0
0
1
1
1
0
0
0
0
0
0
1
1
1
1
0
0
0
0
0
Cursor position
Line
position
EPROM addresses A11 to A3 correspond to a character code.
EPROM addresses A3 to A0 specify a line position of the character pattern.
EPROM data O4 to O0 correspond to character pattern data.
EPROM data O5 to O7 must be specified as 0.
A lit display position (black) corresponds to a 1.
Line 11 and the following lines must be blanked with 0s for a 5 × 10 dot character fonts.
HD44780U
Table 4
Lower
4 Bits
Upper 4
Bits
Correspondence between Character Codes and Character Patterns (ROM Code: A00)
0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010
xxxx0000
CG
RAM
(1)
xxxx0001
(2)
xxxx0010
(3)
xxxx0011
(4)
xxxx0100
(5)
xxxx0101
(6)
xxxx0110
(7)
xxxx0111
(8)
xxxx1000
(1)
xxxx1001
(2)
xxxx1010
(3)
xxxx1011
(4)
xxxx1100
(5)
xxxx1101
(6)
xxxx1110
(7)
xxxx1111
(8)
1011 1100 1101 1110 1111
Note: The user can specify any pattern for character-generator RAM.
17
HD44780U
Table 4
Lower
4 Bits
Upper 4
Bits
Correspondence between Character Codes and Character Patterns (ROM Code: A02)
0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111
xxxx0000
CG
RAM
(1)
xxxx0001
(2)
xxxx0010
(3)
xxxx0011
(4)
xxxx0100
(5)
xxxx0101
(6)
xxxx0110
(7)
xxxx0111
(8)
xxxx1000
(1)
xxxx1001
(2)
xxxx1010
(3)
xxxx1011
(4)
xxxx1100
(5)
xxxx1101
(6)
xxxx1110
(7)
xxxx1111
(8)
18
HD44780U
Table 5
Relationship between CGRAM Addresses, Character Codes (DDRAM) and Character
Patterns (CGRAM Data)
For 5 × 8 dot character patterns
Character Codes
(DDRAM data)
CGRAM Address
Character Patterns
(CGRAM data)
7 6 5 4 3 2 1 0
5 4 3 2 1 0
7 6 5 4 3 2 1 0
High
High
High
Low
0 0 0 0 * 0 0 0
0 0 0 0 * 0 0 1
0 0 0 0 * 1 1 1
0 0 0
0 0 1
1 1 1
Low
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
1
1
1
1
0
0
1
1
0
1
0
1
* * *
* * *
* * *
* * *
* * *
Low
1
1
1
1
1
1
1
0
1
0
1
0
1
0
0
0
1
0
0
1
0
0
0
0
0
1
1
0
1
0
0
0
1
0
0
1
1
0
0
0
0
0
1
1
1
1
1
0
1
0
0
1
0
1
0
0
0
1
1
0
1
0
0
0
0
1
1
0
0
0
1
0
1
0
1
0
1
0
0
0
Character
pattern (1)
Cursor position
Character
pattern (2)
Cursor position
* * *
Notes: 1. Character code bits 0 to 2 correspond to CGRAM address bits 3 to 5 (3 bits: 8 types).
2. CGRAM address bits 0 to 2 designate the character pattern line position. The 8th line is the
cursor position and its display is formed by a logical OR with the cursor.
Maintain the 8th line data, corresponding to the cursor display position, at 0 as the cursor display.
If the 8th line data is 1, 1 bits will light up the 8th line regardless of the cursor presence.
3. Character pattern row positions correspond to CGRAM data bits 0 to 4 (bit 4 being at the left).
4. As shown Table 5, CGRAM character patterns are selected when character code bits 4 to 7 are
all 0. However, since character code bit 3 has no effect, the R display example above can be
selected by either character code 00H or 08H.
5. 1 for CGRAM data corresponds to display selection and 0 to non-selection.
* Indicates no effect.
19
HD44780U
Table 5
Relationship between CGRAM Addresses, Character Codes (DDRAM) and Character
Patterns (CGRAM Data) (cont)
For 5 × 10 dot character patterns
Character Codes
(DDRAM data)
CGRAM Address
Character Patterns
(CGRAM data)
7 6 5 4 3 2 1 0
5 4 3 2 1 0
7 6 5 4 3 2 1 0
High
High
High
Low
0 0 0 0 * 0 0 *
0 0 0 0 * 1 1 *
0 0
1 1
Low
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
1
1
1
1
1
1
1
0
0
0
1
1
1
1
0
1
1
0
0
1
1
1
0
1
0
1
0
1
* * *
* * *
* * *
* * *
* * *
Low
0
0
1
1
1
1
1
1
1
1
0
*
0
0
0
1
0
0
1
0
0
0
0
*
0
0
1
0
0
0
1
0
0
0
0
*
0
0
1
0
0
0
1
0
0
0
0
*
0
0
0
1
1
1
0
0
0
0
0
*
Character
pattern
Cursor position
* * * * *
* * *
* * *
* * * * *
* * *
* * * * *
Notes: 1. Character code bits 1 and 2 correspond to CGRAM address bits 4 and 5 (2 bits: 4 types).
2. CGRAM address bits 0 to 3 designate the character pattern line position. The 11th line is the
cursor position and its display is formed by a logical OR with the cursor.
Maintain the 11th line data corresponding to the cursor display positon at 0 as the cursor display.
If the 11th line data is „1“, „1“ bits will light up the 11th line regardless of the cursor presence.
Since lines 12 to 16 are not used for display, they can be used for general data RAM.
3. Character pattern row positions are the same as 5 × 8 dot character pattern positions.
4. CGRAM character patterns are selected when character code bits 4 to 7 are all 0.
However, since character code bits 0 and 3 have no effect, the P display example above can be
selected by character codes 00H, 01H, 08H, and 09H.
5. 1 for CGRAM data corresponds to display selection and 0 to non-selection.
* Indicates no effect.
20
HD44780U
Timing Generation Circuit
The timing generation circuit generates timing signals for the operation of internal circuits such as
DDRAM, CGROM and CGRAM. RAM read timing for display and internal operation timing by MPU
access are generated separately to avoid interfering with each other. Therefore, when writing data to
DDRAM, for example, there will be no undesirable interferences, such as flickering, in areas other than the
display area.
Liquid Crystal Display Driver Circuit
The liquid crystal display driver circuit consists of 16 common signal drivers and 40 segment signal
drivers. When the character font and number of lines are selected by a program, the required common
signal drivers automatically output drive waveforms, while the other common signal drivers continue to
output non-selection waveforms.
Sending serial data always starts at the display data character pattern corresponding to the last address of
the display data RAM (DDRAM).
Since serial data is latched when the display data character pattern corresponding to the starting address
enters the internal shift register, the HD44780U drives from the head display.
Cursor/Blink Control Circuit
The cursor/blink control circuit generates the cursor or character blinking. The cursor or the blinking will
appear with the digit located at the display data RAM (DDRAM) address set in the address counter (AC).
For example (Figure 8), when the address counter is 08H, the cursor position is displayed at DDRAM
address 08H.
AC6 AC5 AC4 AC3 AC2 AC1 AC0
AC
0
0
0
1
0
0
0
Display position
1
2
3
4
5
6
7
8
9
10
11
DDRAM address
(hexadecimal)
00
01
02
03
04
05
06
07
08
09
0A
1
2
3
4
5
6
7
8
9
10
11
00
01
02
03
04
05
06
07
08
09
0A
40
41
42
43
44
45
46
47
48
49
4A
For a 1-line display
cursor position
For a 2-line display
Display position
DDRAM address
(hexadecimal)
cursor position
Note: The cursor or blinking appears when the address counter (AC) selects the character
generator RAM (CGRAM). However, the cursor and blinking become meaningless.
The cursor or blinking is displayed in the meaningless position when the AC is a CGRAM address.
Figure 8 Cursor/Blink Display Example
21
HD44780U
Interfacing to the MPU
The HD44780U can send data in either two 4-bit operations or one 8-bit operation, thus allowing
interfacing with 4- or 8-bit MPUs.
• For 4-bit interface data, only four bus lines (DB4 to DB7) are used for transfer. Bus lines DB0 to DB3
are disabled. The data transfer between the HD44780U and the MPU is completed after the 4-bit data
has been transferred twice. As for the order of data transfer, the four high order bits (for 8-bit operation,
DB4 to DB7) are transferred before the four low order bits (for 8-bit operation, DB0 to DB3).
The busy flag must be checked (one instruction) after the 4-bit data has been transferred twice. Two
more 4-bit operations then transfer the busy flag and address counter data.
• For 8-bit interface data, all eight bus lines (DB0 to DB7) are used.
RS
R/W
E
DB7
IR7
IR3
BF
AC3
DR7
DR3
DB6
IR6
IR2
AC6
AC2
DR6
DR2
DB5
IR5
IR1
AC5
AC1
DR5
DR1
DB4
IR4
IR0
AC4
AC0
DR4
DR0
Instruction register (IR)
write
Busy flag (BF) and
address counter (AC)
read
Figure 9 4-Bit Transfer Example
22
Data register (DR)
read
HD44780U
Reset Function
Initializing by Internal Reset Circuit
An internal reset circuit automatically initializes the HD44780U when the power is turned on. The
following instructions are executed during the initialization. The busy flag (BF) is kept in the busy state
until the initialization ends (BF = 1). The busy state lasts for 10 ms after VCC rises to 4.5 V.
1. Display clear
2. Function set:
DL = 1; 8-bit interface data
N = 0; 1-line display
F = 0; 5 × 8 dot character font
3. Display on/off control:
D = 0; Display off
C = 0; Cursor off
B = 0; Blinking off
4. Entry mode set:
I/D = 1; Increment by 1
S = 0; No shift
Note: If the electrical characteristics conditions listed under the table Power Supply Conditions Using
Internal Reset Circuit are not met, the internal reset circuit will not operate normally and will fail to
initialize the HD44780U. For such a case, initial-ization must be performed by the MPU as
explained in the section, Initializing by Instruction.
Instructions
Outline
Only the instruction register (IR) and the data register (DR) of the HD44780U can be controlled by the
MPU. Before starting the internal operation of the HD44780U, control information is temporarily stored
into these registers to allow interfacing with various MPUs, which operate at different speeds, or various
peripheral control devices. The internal operation of the HD44780U is determined by signals sent from the
MPU. These signals, which include register selection signal (RS), read/
write signal (R/W), and the data bus (DB0 to DB7), make up the HD44780U instructions (Table 6). There
are four categories of instructions that:
•
•
•
•
Designate HD44780U functions, such as display format, data length, etc.
Set internal RAM addresses
Perform data transfer with internal RAM
Perform miscellaneous functions
23
HD44780U
Normally, instructions that perform data transfer with internal RAM are used the most. However, autoincrementation by 1 (or auto-decrementation by 1) of internal HD44780U RAM addresses after each data
write can lighten the program load of the MPU. Since the display shift instruction (Table 11) can perform
concurrently with display data write, the user can minimize system development time with maximum
programming efficiency.
When an instruction is being executed for internal operation, no instruction other than the busy flag/address
read instruction can be executed.
Because the busy flag is set to 1 while an instruction is being executed, check it to make sure it is 0 before
sending another instruction from the MPU.
Note: Be sure the HD44780U is not in the busy state (BF = 0) before sending an instruction from the
MPU to the HD44780U. If an instruction is sent without checking the busy flag, the time between
the first instruction and next instruction will take much longer than the instruction time itself. Refer
to Table 6 for the list of each instruc-tion execution time.
Table 6
Instructions
Code
Execution Time
(max) (when f cp or
f OSC is 270 kHz)
Instruction RS
R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Description
Clear
display
0
0
0
0
0
0
0
0
0
1
Clears entire display and
sets DDRAM address 0 in
address counter.
Return
home
0
0
0
0
0
0
0
0
1
—
Sets DDRAM address 0 in
address counter. Also
returns display from being
shifted to original position.
DDRAM contents remain
unchanged.
1.52 ms
Entry
mode set
0
0
0
0
0
0
0
1
I/D
S
Sets cursor move direction
and specifies display shift.
These operations are
performed during data write
and read.
37 µs
Display
on/off
control
0
0
0
0
0
0
1
D
C
B
Sets entire display (D) on/off, 37 µs
cursor on/off (C), and
blinking of cursor position
character (B).
Cursor or
display
shift
0
0
0
0
0
1
S/C R/L
—
—
Moves cursor and shifts
display without changing
DDRAM contents.
Function
set
0
0
0
0
1
DL
N
—
—
Sets interface data length
37 µs
(DL), number of display lines
(N), and character font (F).
Set
CGRAM
address
0
0
0
1
ACG ACG ACG ACG ACG ACG Sets CGRAM address.
CGRAM data is sent and
received after this setting.
37 µs
Set
DDRAM
address
0
0
1
ADD ADD ADD ADD ADD ADD ADD Sets DDRAM address.
DDRAM data is sent and
received after this setting.
37 µs
Read busy 0
flag &
address
1
BF
AC
0 µs
24
AC
AC
AC
F
AC
AC
AC
Reads busy flag (BF)
indicating internal operation
is being performed and
reads address counter
contents.
37 µs
HD44780U
Table 6
Instructions (cont)
Execution Time
(max) (when f cp or
f OSC is 270 kHz)
Code
Instruction RS
R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Description
Write data
to CG or
DDRAM
1
0
Write data
Writes data into DDRAM or
CGRAM.
37 µs
tADD = 4 µs*
Read data 1
from CG or
DDRAM
1
Read data
Reads data from DDRAM or
CGRAM.
37 µs
tADD = 4 µs*
= 1:
= 0:
= 1:
= 1:
= 0:
= 1:
= 0:
= 1:
= 1:
= 1:
= 1:
= 0:
Increment
Decrement
Accompanies display shift
Display shift
Cursor move
Shift to the right
Shift to the left
8 bits, DL = 0: 4 bits
2 lines, N = 0: 1 line
5 × 10 dots, F = 0: 5 × 8 dots
Internally operating
Instructions acceptable
DDRAM: Display data RAM
CGRAM: Character generator
RAM
ACG:
CGRAM address
ADD:
DDRAM address
(corresponds to cursor
address)
AC: Address counter used for
both DD and CGRAM
addresses
Execution time
changes when
frequency changes
Example:
When fcp or fOSC is
250 kHz,
270
37 µs ×
= 40 µs
250
I/D
I/D
S
S/C
S/C
R/L
R/L
DL
N
F
BF
BF
Note:
— indicates no effect.
* After execution of the CGRAM/DDRAM data write or read instruction, the RAM address counter
is incremented or decremented by 1. The RAM address counter is updated after the busy flag
turns off. In Figure 10, tADD is the time elapsed after the busy flag turns off until the address
counter is updated.
Busy signal
(DB7 pin)
Address counter
(DB0 to DB6 pins)
Busy state
A
A+1
t ADD
Note: t ADD depends on the operation frequency
t ADD = 1.5/(f cp or f OSC ) seconds
Figure 10 Address Counter Update
25
HD44780U
Instruction Description
Clear Display
Clear display writes space code 20H (character pattern for character code 20H must be a blank pattern) into
all DDRAM addresses. It then sets DDRAM address 0 into the address counter, and returns the display to
its original status if it was shifted. In other words, the display disappears and the cursor or blinking goes to
the left edge of the display (in the first line if 2 lines are displayed). It also sets I/D to 1 (increment mode)
in entry mode. S of entry mode does not change.
Return Home
Return home sets DDRAM address 0 into the address counter, and returns the display to its original status
if it was shifted. The DDRAM contents do not change.
The cursor or blinking go to the left edge of the display (in the first line if 2 lines are displayed).
Entry Mode Set
I/D: Increments (I/D = 1) or decrements (I/D = 0) the DDRAM address by 1 when a character code is
written into or read from DDRAM.
The cursor or blinking moves to the right when incremented by 1 and to the left when decremented by 1.
The same applies to writing and reading of CGRAM.
S: Shifts the entire display either to the right (I/D = 0) or to the left (I/D = 1) when S is 1. The display does
not shift if S is 0.
If S is 1, it will seem as if the cursor does not move but the display does. The display does not shift when
reading from DDRAM. Also, writing into or reading out from CGRAM does not shift the display.
Display On/Off Control
D: The display is on when D is 1 and off when D is 0. When off, the display data remains in DDRAM, but
can be displayed instantly by setting D to 1.
C: The cursor is displayed when C is 1 and not displayed when C is 0. Even if the cursor disappears, the
function of I/D or other specifications will not change during display data write. The cursor is displayed
using 5 dots in the 8th line for 5 × 8 dot character font selection and in the 11th line for the 5 × 10 dot
character font selection (Figure 13).
B: The character indicated by the cursor blinks when B is 1 (Figure 13). The blinking is displayed as
switching between all blank dots and displayed characters at a speed of 409.6-ms intervals when fcp or f OSC
is 250 kHz. The cursor and blinking can be set to display simultaneously. (The blinking frequency changes
according to f OSC or the reciprocal of f cp . For example, when fcp is 270 kHz, 409.6 × 250/270 = 379.2 ms.)
26
HD44780U
Cursor or Display Shift
Cursor or display shift shifts the cursor position or display to the right or left without writing or reading
display data (Table 7). This function is used to correct or search the display. In a 2-line display, the cursor
moves to the second line when it passes the 40th digit of the first line. Note that the first and second line
displays will shift at the same time.
When the displayed data is shifted repeatedly each line moves only horizontally. The second line display
does not shift into the first line position.
The address counter (AC) contents will not change if the only action performed is a display shift.
Function Set
DL: Sets the interface data length. Data is sent or received in 8-bit lengths (DB7 to DB0) when DL is 1,
and in 4-bit lengths (DB7 to DB4) when DL is 0.When 4-bit length is selected, data must be sent or
received twice.
N: Sets the number of display lines.
F: Sets the character font.
Note: Perform the function at the head of the program before executing any instructions (except for the
read busy flag and address instruction). From this point, the function set instruction cannot be
executed unless the interface data length is changed.
Set CGRAM Address
Set CGRAM address sets the CGRAM address binary AAAAAA into the address counter.
Data is then written to or read from the MPU for CGRAM.
27
HD44780U
RS
Clear
display
Code
0
RS
Return
home
Code
0
RS
Entry
mode set
Code
0
RS
Display
on/off control
Code
0
RS
Cursor or
display shift
Code
0
RS
Function set
Code
0
RS
Set CGRAM
address
Code
0
R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
0
0
0
0
0
0
0
1
R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
0
0
0
0
0
0
0
1
*
Note: * Don’t care.
R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
0
0
0
0
0
0
1
I/D
S
R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
0
0
0
0
0
1
D
C
B
R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
0
0
0
0
1
S/C
R/L
*
*
R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
0
0
0
1
DL
N
F
*
*
R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
0
0
1
A
A
A
Higher
order bit
Figure 11 Instruction (1)
28
0
A
A
Lower
order bit
A
Note: * Don’t care.
HD44780U
Set DDRAM Address
Set DDRAM address sets the DDRAM address binary AAAAAAA into the address counter.
Data is then written to or read from the MPU for DDRAM.
However, when N is 0 (1-line display), AAAAAAA can be 00H to 4FH. When N is 1 (2-line display),
AAAAAAA can be 00H to 27H for the first line, and 40H to 67H for the second line.
Read Busy Flag and Address
Read busy flag and address reads the busy flag (BF) indicating that the system is now internally operating
on a previously received instruction. If BF is 1, the internal operation is in progress. The next instruction
will not be accepted until BF is reset to 0. Check the BF status before the next write operation. At the same
time, the value of the address counter in binary AAAAAAA is read out. This address counter is used by
both CG and DDRAM addresses, and its value is determined by the previous instruction. The address
contents are the same as for instructions set CGRAM address and set DDRAM address.
Table 7
Shift Function
S/C
R/L
0
0
Shifts the cursor position to the left. (AC is decremented by one.)
0
1
Shifts the cursor position to the right. (AC is incremented by one.)
1
0
Shifts the entire display to the left. The cursor follows the display shift.
1
1
Shifts the entire display to the right. The cursor follows the display shift.
Table 8
Function Set
N
F
No. of
Display
Lines
0
0
1
5 × 8 dots
1/8
0
1
1
5 × 10 dots
1/11
1
*
2
5 × 8 dots
1/16
Note:
*
Character Font
Duty
Factor
Remarks
Cannot display two lines for 5 × 10 dot character font
Indicates don’t care.
29
HD44780U
Cursor
5 × 8 dot
character font
5 × 10 dot
character font
Alternating display
Cursor display example
Blink display example
Figure 12 Cursor and Blinking
RS
Set DDRAM
address
Code
0
R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
0
1
A
A
A
A
Higher
order bit
RS
Read busy flag
and address
Code
0
A
A
Lower
order bit
R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
1
BF
A
A
A
Higher
order bit
Figure 13 Instruction (2)
30
A
A
A
A
Lower
order bit
A
HD44780U
Write Data to CG or DDRAM
Write data to CG or DDRAM writes 8-bit binary data DDDDDDDD to CG or DDRAM.
To write into CG or DDRAM is determined by the previous specification of the CGRAM or DDRAM
address setting. After a write, the address is automatically incremented or decremented by 1 according to
the entry mode. The entry mode also determines the display shift.
Read Data from CG or DDRAM
Read data from CG or DDRAM reads 8-bit binary data DDDDDDDD from CG or DDRAM.
The previous designation determines whether CG or DDRAM is to be read. Before entering this read
instruction, either CGRAM or DDRAM address set instruction must be executed. If not executed, the first
read data will be invalid. When serially executing read instructions, the next address data is normally read
from the second read. The address set instructions need not be executed just before this read instruction
when shifting the cursor by the cursor shift instruction (when reading out DDRAM). The operation of the
cursor shift instruction is the same as the set DDRAM address instruction.
After a read, the entry mode automatically increases or decreases the address by 1. However, display shift
is not executed regardless of the entry mode.
Note: The address counter (AC) is automatically incremented or decremented by 1 after the write
instructions to CGRAM or DDRAM are executed. The RAM data selected by the AC cannot be
read out at this time even if read instructions are executed. Therefore, to correctly read data,
execute either the address set instruction or cursor shift instruction (only with DDRAM), then just
before reading the desired data, execute the read instruction from the second time the read
instruction is sent.
RS
Write data to
CG or DDRAM
Code
1
R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
0
D
D
D
D
D
Higher
order bits
RS
Read data from
CG or DDRAM
Code
1
D
D
D
Lower
order bits
R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
1
D
D
D
Higher
order bits
D
D
D
D
D
Lower
order bits
Figure 14 Instruction (3)
31
HD44780U
Interfacing the HD44780U
Interface to MPUs
+
,
&
%
0)*#
• Interfacing to an 8-bit MPU
See Figure 16 for an example of using a I/O port (for a single-chip microcomputer) as an interface
device.
In this example, P30 to P37 are connected to the data bus DB0 to DB7, and P75 to P77 are connected to
E, R/W, and RS, respectively.
RS
R/W
E
Internal
operation
Functioning
Data
Busy
Busy
Instruction
write
Busy flag
check
Busy flag
check
DB7
Not
busy
Data
Busy flag
check
Instruction
write
Figure 15 Example of Busy Flag Check Timing Sequence
H8/325
HD44780U
P30 to P37
P77
P76
P75
8
DB0 to DB7
COM1 to
COM16
16
E
RS
R/W
SEG1 to
SEG40
40
LCD
Figure 16 H8/325 Interface (Single-Chip Mode)
32
HD44780U
• Interfacing to a 4-bit MPU
The HD44780U can be connected to the I/O port of a 4-bit MPU. If the I/O port has enough bits, 8-bit
data can be transferred. Otherwise, one data transfer must be made in two operations for 4-bit data. In
this case, the timing sequence becomes somewhat complex. (See Figure 17.)
See Figure 18 for an interface example to the HMCS4019R.
Note that two cycles are needed for the busy flag check as well as for the data transfer. The 4-bit
operation is selected by the program.
RS
*
$
#
!"()'./
R/W
E
Internal
operation
DB7
Functioning
IR7
IR3
Instruction
write
Busy AC3
Not
busy AC3
Busy flag
check
Busy flag
check
D7
D3
Instruction
write
Note: IR7 , IR3 are the 7th and 3rd bits of the instruction.
AC3 is the 3rd bit of the address counter.
Figure 17 Example of 4-Bit Data Transfer Timing Sequence
HMCS4019R
HD44780
D15
RS
D14
R/W
D13
E
4
R10 to R13
DB4 to DB7
COM1 to
COM16
16
LCD
SEG1 to
SEG40
40
Figure 18 Example of Interface to HMCS4019R
33
HD44780U
Interface to Liquid Crystal Display
Character Font and Number of Lines: The HD44780U can perform two types of displays, 5 × 8 dot and
5 × 10 dot character fonts, each with a cursor.
Up to two lines are displayed for 5 × 8 dots and one line for 5 × 10 dots. Therefore, a total of three
types of common signals are available (Table 9).
The number of lines and font types can be selected by the program. (See Table 6, Instructions.)
Connection to HD44780 and Liquid Crystal Display: See Figure 19 for the connection examples.
Table 9
Common Signals
Number of Lines
Character Font
Number of Common Signals
Duty Factor
1
5 × 8 dots + cursor
8
1/8
1
5 × 10 dots + cursor
11
1/11
2
5 × 8 dots + cursor
16
1/16
HD44780
COM1
COM8
SEG1
SEG40
Example of a 5 × 8 dot, 8-character × 1-line display (1/4 bias, 1/8 duty cycle)
HD44780
COM1
COM11
SEG1
SEG40
Example of a 5 × 10 dot, 8-character × 1-line display (1/4 bias, 1/11 duty cycle)
Figure 19 Liquid Crystal Display and HD44780 Connections
34
HD44780U
Since five segment signal lines can display one digit, one HD44780U can display up to 8 digits for a 1-line
display and 16 digits for a 2-line display.
The examples in Figure 19 have unused common signal pins, which always output non-selection
waveforms. When the liquid crystal display panel has unused extra scanning lines, connect the extra
scanning lines to these common signal pins to avoid any undesirable effects due to crosstalk during the
floating state.
HD44780
COM1
COM8
COM9
COM16
SEG1
SEG40
Example of a 5 × 8 dot, 8-character × 2-line display (1/5 bias, 1/16 duty cycle)
Figure 19 Liquid Crystal Display and HD44780 Connections (cont)
35
HD44780U
Connection of Changed Matrix Layout: In the preceding examples, the number of lines correspond to the
scanning lines. However, the following display examples (Figure 20) are made possible by altering the
matrix layout of the liquid crystal display panel. In either case, the only change is the layout. The display
characteristics and the number of liquid crystal display characters depend on the number of common
signals or on duty factor. Note that the display data RAM (DDRAM) addresses for 4 characters × 2 lines
and for 16 characters × 1 line are the same as in Figure 19.
HD44780
COM1
COM8
SEG1
SEG40
COM9
COM16
5 × 8 dot, 16-character × 1-line display
(1/5 bias, 1/16 duty cycle)
Figure 20 Changed Matrix Layout Displays
36
HD44780U
Power Supply for Liquid Crystal Display Drive
Various voltage levels must be applied to pins V1 to V5 of the HD44780U to obtain the liquid crystal
display drive waveforms. The voltages must be changed according to the duty factor (Table 10).
VLCD is the peak value for the liquid crystal display drive waveforms, and resistance dividing provides
voltages V1 to V5 (Figure 21).
Table 10
Duty Factor and Power Supply for Liquid Crystal Display Drive
Duty Factor
1/8, 1/11
1/16
Bias
Power Supply
1/4
1/5
V1
VCC–1/4 VLCD
VCC–1/5 VLCD
V2
VCC–1/2 VLCD
VCC–2/5 VLCD
V3
VCC–1/2 VLCD
VCC–3/5 VLCD
V4
VCC–3/4 VLCD
VCC–4/5 VLCD
V5
VCC–VLCD
VCC–VLCD
VCC (+5 V)
VCC (+5 V)
VCC
VCC
R
V2
R
V3
R
R
VLCD
V4
R
V5
V2
R
VLCD
V3
R
V4
R
V5
VR
VR
–5 V
–5 V
1/4 bias
(1/8, 1/11 duty cycle)
R
V1
V1
1/5 bias
(1/16, duty cycle)
Figure 21 Drive Voltage Supply Example
37
HD44780U
Relationship between Oscillation Frequency and Liquid Crystal Display Frame
Frequency
The liquid crystal display frame frequencies of Figure 22 apply only when the oscillation frequency is 270
kHz (one clock pulse of 3.7 µs).
1/8 duty cycle
COM1
400 clocks
1
2
3
4
8
1
2
11
1
2
1
2
VCC
V1
V2 (V3)
V4
V5
1 frame
1 frame = 3.7 µs × 400 × 8 = 11850 µs = 11.9 ms
1
Frame frequency =
= 84.3 Hz
11.9 ms
1/11 duty cycle
COM1
400 clocks
1
2
3
4
VCC
V1
V2 (V3)
V4
V5
1 frame
1 frame = 3.7 µs × 400 × 11 = 16300 µs = 16.3 ms
1
Frame frequency =
= 61.4 Hz
16.3 ms
1/16 duty cycle
COM1
200 clocks
1
2
3
4
16
VCC
V1
V2
V3
V4
V5
1 frame
1 frame = 3.7 µs × 200 × 16 = 11850 µs = 11.9 ms
1
Frame frequency =
= 84.3 Hz
11.9 ms
Figure 22 Frame Frequency
38
HD44780U
Instruction and Display Correspondence
• 8-bit operation, 8-digit × 1-line display with internal reset
Refer to Table 11 for an example of an 8-digit × 1-line display in 8-bit operation. The HD44780U
functions must be set by the function set instruction prior to the display. Since the display data RAM
can store data for 80 characters, as explained before, the RAM can be used for displays such as for
advertising when combined with the display shift operation.
Since the display shift operation changes only the display position with DDRAM contents unchanged,
the first display data entered into DDRAM can be output when the return home operation is performed.
• 4-bit operation, 8-digit × 1-line display with internal reset
The program must set all functions prior to the 4-bit operation (Table 12). When the power is turned on,
8-bit operation is automatically selected and the first write is performed as an 8-bit operation. Since
DB0 to DB3 are not connected, a rewrite is then required. However, since one operation is completed in
two accesses for 4-bit operation, a rewrite is needed to set the functions (see Table 12). Thus, DB4 to
DB7 of the function set instruction is written twice.
• 8-bit operation, 8-digit × 2-line display
For a 2-line display, the cursor automatically moves from the first to the second line after the 40th digit
of the first line has been written. Thus, if there are only 8 characters in the first line, the DDRAM
address must be again set after the 8th character is completed. (See Table 13.) Note that the display shift
operation is performed for the first and second lines. In the example of Table 13, the display shift is
performed when the cursor is on the second line. However, if the shift operation is performed when the
cursor is on the first line, both the first and second lines move together. If the shift is repeated, the
display of the second line will not move to the first line. The same display will only shift within its own
line for the number of times the shift is repeated.
Note: When using the internal reset, the electrical characteristics in the Power Supply Conditions Using
Internal Reset Circuit table must be satisfied. If not, the HD44780U must be initialized by
instructions. See the section, Initializing by Instruction.
39
HD44780U
Table 11
Step
No. RS
8-Bit Operation, 8-Digit × 1-Line Display Example with Internal Reset
Instruction
R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Display
Operation
1
Power supply on (the HD44780U is initialized by the internal
reset circuit)
Initialized. No display.
2
Function set
0
0
0
Sets to 8-bit operation and
selects 1-line display and 5 × 8
dot character font. (Number of
display lines and character
fonts cannot be changed after
step #2.)
3
4
5
6
0
1
1
0
0
*
*
Display on/off control
0
0
0
0
0
0
1
1
1
0
Entry mode set
0
0
0
0
0
0
1
1
0
Write data to CGRAM/DDRAM
1
0
0
1
0
0
1
0
0
0
Write data to CGRAM/DDRAM
1
0
0
1
0
0
1
0
0
1
0
7
8
9
10
40
·
·
·
·
·
1
0
0
1
Entry mode set
0
0
0
0
0
1
1
1
Write data to CGRAM/DDRAM
1
0
0
0
1
0
0
0
0
0
0
Sets mode to increment the
address by one and to shift the
cursor to the right at the time of
write to the DD/CGRAM.
Display is not shifted.
_
Writes H. DDRAM has already
been selected by initialization
when the power was turned on.
The cursor is incremented by
one and shifted to the right.
H_
Writes I.
HI_
·
·
·
·
·
Write data to CGRAM/DDRAM
1
0
0
1
0
0
0
Turns on display and cursor.
Entire display is in space mode
because of initialization.
_
HITACHI_
HITACHI_
ITACHI _
Writes I.
Sets mode to shift display at
the time of write.
Writes a space.
HD44780U
Table 11
Step
No. RS
11
8-Bit Operation, 8-Digit × 1-Line Display Example with Internal Reset (cont)
Instruction
R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Display
Write data to CGRAM/DDRAM
1
0
0
1
0
0
12
13
14
15
16
17
18
19
1
0
1
·
·
·
·
·
1
1
1
1
Cursor or display shift
0
0
0
0
0
1
0
0
*
*
Cursor or display shift
0
0
0
0
0
1
0
0
*
*
Write data to CGRAM/DDRAM
1
0
0
1
0
0
0
0
1
1
Cursor or display shift
0
0
0
0
0
1
1
1
*
*
Cursor or display shift
0
0
0
0
0
1
0
1
*
*
Write data to CGRAM/DDRAM
1
0
0
1
0
0
1
1
0
1
·
·
·
·
·
Return home
0
0
0
0
0
TACHI M_
Writes M.
·
·
·
·
·
Write data to CGRAM/DDRAM
1
0
0
1
0
0
20
21
1
Operation
MICROKO_
Writes O.
MICROKO
_
Shifts only the cursor position
to the left.
MICROKO
_
Shifts only the cursor position
to the left.
ICROCO
_
Writes C over K.
The display moves to the left.
MICROCO
_
Shifts the display and cursor
position to the right.
MICROCO_
Shifts the display and cursor
position to the right.
ICROCOM_
Writes M.
·
·
·
·
·
0
0
0
1
0
HITACHI
_
Returns both display and
cursor to the original position
(address 0).
41
HD44780U
Table 12
Step
No. RS
4-Bit Operation, 8-Digit × 1-Line Display Example with Internal Reset
Instruction
R/W DB7 DB6 DB5 DB4
Display
Operation
1
Power supply on (the HD44780U is initialized by the internal
reset circuit)
Initialized. No display.
2
Function set
0
0
0
0
1
0
Sets to 4-bit operation.
In this case, operation is
handled as 8 bits by initialization, and only this instruction
completes with one write.
Function set
0
0
0
0
0
0
0
0
1
*
0
*
Display on/off control
0
0
0
0
0
0
1
1
0
1
0
0
Entry mode set
0
0
0
0
0
0
0
1
0
0
3
4
5
6
Note:
42
0
1
Write data to CGRAM/DDRAM
1
0
0
1
0
0
1
0
1
0
0
0
Sets 4-bit operation and
selects 1-line display and 5 × 8
dot character font. 4-bit
operation starts from this step
and resetting is necessary.
(Number of display lines and
character fonts cannot be
changed after step #3.)
_
_
H_
The control is the same as for 8-bit operation beyond step #6.
Turns on display and cursor.
Entire display is in space mode
because of initialization.
Sets mode to increment the
address by one and to shift the
cursor to the right at the time of
write to the DD/CGRAM.
Display is not shifted.
Writes H.
The cursor is incremented by
one and shifts to the right.
HD44780U
Table 13
Step
No. RS
8-Bit Operation, 8-Digit × 2-Line Display Example with Internal Reset
Instruction
R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Display
Operation
1
Power supply on (the HD44780U is initialized by the internal
reset circuit)
Initialized. No display.
2
Function set
0
0
0
Sets to 8-bit operation and
selects 2-line display and 5 × 8
dot character font.
3
4
5
0
1
1
1
0
*
*
Display on/off control
0
0
0
0
0
0
1
1
1
0
Entry mode set
0
0
0
0
0
0
1
1
0
Write data to CGRAM/DDRAM
1
0
0
1
0
0
1
0
0
0
0
6
7
8
·
·
·
·
·
Sets mode to increment the
address by one and to shift the
cursor to the right at the time of
write to the DD/CGRAM.
Display is not shifted.
_
Writes H. DDRAM has already
been selected by initialization
when the power was turned on.
The cursor is incremented by
one and shifted to the right.
H_
·
·
·
·
·
Write data to CGRAM/DDRAM
1
0
0
1
0
0
1
0
0
1
Set DDRAM address
0
0
1
1
0
0
0
0
0
Turns on display and cursor.
All display is in space mode
because of initialization.
_
0
HITACHI_
HITACHI
_
Writes I.
Sets DDRAM address so that
the cursor is positioned at the
head of the second line.
43
HD44780U
Table 13
Step
No. RS
9
8-Bit Operation, 8-Digit × 2-Line Display Example with Internal Reset (cont)
Instruction
R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Display
Write data to CGRAM/DDRAM
1
0
0
1
0
0
10
11
12
13
44
1
0
1
·
·
·
·
·
HITACHI
M_
1
1
1
1
HITACHI
MICROCO_
Entry mode set
0
0
0
0
0
1
1
1
HITACHI
MICROCO_
Write data to CGRAM/DDRAM
1
0
0
1
0
0
1
1
0
1
ITACHI
ICROCOM_
0
0
·
·
·
·
·
Return home
0
0
0
0
0
Writes M.
·
·
·
·
·
Write data to CGRAM/DDRAM
1
0
0
1
0
0
14
15
1
Operation
Writes O.
Sets mode to shift display at
the time of write.
Writes M. Display is shifted to
the left. The first and second
lines both shift at the same
time.
·
·
·
·
·
0
0
0
1
0
HITACHI
_
MICROCOM
Returns both display and
cursor to the original position
(address 0).
HD44780U
Initializing by Instruction
If the power supply conditions for correctly operating the internal reset circuit are not met, initialization by
instructions becomes necessary.
Refer to Figures 23 and 24 for the procedures on 8-bit and 4-bit initializations, respectively.
Power on
Wait for more than 40 ms
after VCC rises to 2.7 V
Wait for more than 15 ms
after VCC rises to 4.5 V
RS R/WDB7 DB6 DB5 DB4 DB3DB2 DB1 DB0
0 0 0 0 1 1 * * * *
BF cannot be checked before this instruction.
Function set (Interface is 8 bits long.)
Wait for more than 4.1 ms
RS R/WDB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
0 0 0 0 1 1 * * * *
BF cannot be checked before this instruction.
Function set (Interface is 8 bits long.)
Wait for more than 100 µs
RS R/WDB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
0 0 0 0 1 1 * * * *
BF cannot be checked before this instruction.
Function set (Interface is 8 bits long.)
BF can be checked after the following instructions.
When BF is not checked, the waiting time between
instructions is longer than the execution instuction
time. (See Table 6.)
RS R/WDB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
0 0 0 0 1 1 N F * *
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
1
I/D S
Function set (Interface is 8 bits long. Specify the
number of display lines and character font.)
The number of display lines and character font
cannot be changed after this point.
Display off
Display clear
Entry mode set
Initialization ends
Figure 23 8-Bit Interface
45
HD44780U
Power on
Wait for more than 15 ms
after VCC rises to 4.5 V
RS R/W DB7 DB6 DB5 DB4
0 0 0 0 1 1
Wait for more than 40 ms
after VCC rises to 2.7 V
BF cannot be checked before this instruction.
Function set (Interface is 8 bits long.)
Wait for more than 4.1 ms
RS R/W DB7 DB6 DB5 DB4
0 0 0 0 1 1
BF cannot be checked before this instruction.
Function set (Interface is 8 bits long.)
Wait for more than 100 µs
RS R/W DB7 DB6 DB5 DB4
0 0 0 0 1 1
BF cannot be checked before this instruction.
RS R/W DB7 DB6 DB5 DB4
0 0 0 0 1 0
BF can be checked after the following instructions.
When BF is not checked, the waiting time between
instructions is longer than the execution instuction
time. (See Table 6.)
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
N
0
1
0
0
0
0
0
F
0
0
0
0
0
1
1
0
* *
0 0
0 0
0 0
0 1
0 0
I/D S
Function set (Interface is 8 bits long.)
Function set (Set interface to be 4 bits long.)
Interface is 8 bits in length.
Function set (Interface is 4 bits long. Specify the
number of display lines and character font.)
The number of display lines and character font
cannot be changed after this point.
Display off
Display clear
Initialization ends
Entry mode set
Figure 24 4-Bit Interface
46
HD44780U
Absolute Maximum Ratings*
Item
Symbol
Value
Unit
Notes
Power supply voltage (1)
VCC–GND
–0.3 to +7.0
V
1
Power supply voltage (2)
VCC–V5
–0.3 to +13.0
V
1, 2
Input voltage
Vt
–0.3 to VCC +0.3
V
1
Operating temperature
Topr
–30 to +75
°C
Storage temperature
Tstg
–55 to +125
°C
Note:
*
4
If the LSI is used above these absolute maximum ratings, it may become permanently damaged.
Using the LSI within the following electrical characteristic limits is strongly recommended for
normal operation. If these electrical characteristic conditions are also exceeded, the LSI will
malfunction and cause poor reliability.
47
HD44780U
DC Characteristics (VCC = 2.7 to 4.5 V, Ta = –30 to +75°C*3)
Item
Symbol
Min
Typ
Max
Unit
Input high voltage (1)
(except OSC1)
VIH1
0.7V CC
—
VCC
V
6
Input low voltage (1)
(except OSC1)
VIL1
–0.3
—
0.55
V
6
Input high voltage (2)
(OSC1)
VIH2
0.7V CC
—
VCC
V
15
Input low voltage (2)
(OSC1)
VIL2
—
—
0.2V CC
V
15
Output high voltage (1) VOH1
(DB0–DB7)
0.75V CC
—
—
V
–I OH = 0.1 mA
7
Output low voltage (1)
(DB0–DB7)
—
—
0.2V CC
V
I OL = 0.1 mA
7
Output high voltage (2) VOH2
(except DB0–DB7)
0.8V CC
—
—
V
–I OH = 0.04 mA
8
Output low voltage (2)
(except DB0–DB7)
VOL2
—
—
0.2V CC
V
I OL = 0.04 mA
8
Driver on resistance
(COM)
RCOM
—
2
20
kΩ
±Id = 0.05 mA,
VLCD = 4 V
13
Driver on resistance
(SEG)
RSEG
—
2
30
kΩ
±Id = 0.05 mA,
VLCD = 4 V
13
Input leakage current
I LI
–1
—
1
µA
VIN = 0 to VCC
9
Pull-up MOS current
(DB0–DB7, RS, R/W)
–I p
10
50
120
µA
VCC = 3 V
Power supply current
I CC
—
150
300
µA
Rf oscillation,
external clock
VCC = 3 V,
f OSC = 270 kHz
LCD voltage
VLCD1
3.0
—
11.0
V
VCC–V5, 1/5 bias 16
VLCD2
3.0
—
11.0
V
VCC–V5, 1/4 bias 16
Note:
48
*
VOL1
Test Condition Notes*
Refer to the Electrical Characteristics Notes section following these tables.
10, 14
HD44780U
AC Characteristics (VCC = 2.7 to 4.5 V, Ta = –30 to +75°C*3)
Clock Characteristics
Item
Symbol Min
Typ
Max
Unit
External External clock frequency
clock
External clock duty
operation
External clock rise time
f cp
125
250
350
kHz
Duty
45
50
55
%
t rcp
—
—
0.2
µs
t fcp
—
—
0.2
µs
190
270
350
kHz
External clock fall time
Rf
Clock oscillation frequency f OSC
oscillation
Note:
*
Test Condition Note*
11
Rf = 75 kΩ,
VCC = 3 V
12
Refer to the Electrical Characteristics Notes section following these tables.
Bus Timing Characteristics
Write Operation
Item
Symbol
Min
Typ
Max
Unit
Test Condition
Enable cycle time
t cycE
1000
—
—
ns
Figure 25
Enable pulse width (high level)
PWEH
450
—
—
Enable rise/fall time
t Er, t Ef
—
—
25
Address set-up time (RS, R/W to E) t AS
60
—
—
Address hold time
t AH
20
—
—
Data set-up time
t DSW
195
—
—
Data hold time
tH
10
—
—
Item
Symbol
Min
Typ
Max
Unit
Test Condition
Enable cycle time
t cycE
1000
—
—
ns
Figure 26
Enable pulse width (high level)
PWEH
450
—
—
Enable rise/fall time
t Er, t Ef
—
—
25
Address set-up time (RS, R/W to E) t AS
60
—
—
Address hold time
t AH
20
—
—
Data delay time
t DDR
—
—
360
Data hold time
t DHR
5
—
—
Read Operation
49
HD44780U
Interface Timing Characteristics with External Driver
Item
Symbol
Min
Typ
Max
Unit
Test Condition
High level
t CWH
800
—
—
ns
Figure 27
Low level
t CWL
800
—
—
Clock set-up time
t CSU
500
—
—
Data set-up time
t SU
300
—
—
Data hold time
t DH
300
—
—
M delay time
t DM
–1000
—
1000
Clock rise/fall time
t ct
—
—
200
Clock pulse width
Power Supply Conditions Using Internal Reset Circuit
Item
Symbol
Min
Typ
Max
Unit
Test Condition
Power supply rise time
t r CC
0.1
—
10
ms
Figure 28
Power supply off time
t OFF
1
—
—
50
HD44780U
DC Characteristics (VCC = 4.5 to 5.5 V, Ta = –30 to +75°C*3)
Item
Symbol
Min
Typ
Max
Unit
Input high voltage (1)
(except OSC1)
VIH1
2.2
—
VCC
V
6
Input low voltage (1)
(except OSC1)
VIL1
–0.3
—
0.6
V
6
Input high voltage (2)
(OSC1)
VIH2
VCC–1.0
—
VCC
V
15
Input low voltage (2)
(OSC1)
VIL2
—
—
1.0
V
15
Output high voltage (1) VOH1
(DB0–DB7)
2.4
—
—
V
–I OH = 0.205 mA
7
Output low voltage (1)
(DB0–DB7)
—
—
0.4
V
I OL = 1.2 mA
7
Output high voltage (2) VOH2
(except DB0–DB7)
0.9 VCC
—
—
V
–I OH = 0.04 mA
8
Output low voltage (2)
(except DB0–DB7)
VOL2
—
—
0.1 VCC
V
I OL = 0.04 mA
8
Driver on resistance
(COM)
RCOM
—
2
20
kΩ
±Id = 0.05 mA,
VLCD = 4 V
13
Driver on resistance
(SEG)
RSEG
—
2
30
kΩ
±Id = 0.05 mA,
VLCD = 4 V
13
Input leakage current
I LI
–1
—
1
µA
VIN = 0 to VCC
9
Pull-up MOS current
(DB0–DB7, RS, R/W)
–I p
50
125
250
µA
VCC = 5 V
Power supply current
I CC
—
350
600
µA
Rf oscillation,
external clock
VCC = 5 V,
f OSC = 270 kHz
10, 14
LCD voltage
VLCD1
3.0
—
11.0
V
VCC–V5, 1/5 bias
16
VLCD2
3.0
—
11.0
V
VCC–V5, 1/4 bias
16
Note:
*
VOL1
Test Condition
Notes*
Refer to the Electrical Characteristics Notes section following these tables.
51
HD44780U
AC Characteristics (VCC = 4.5 to 5.5 V, Ta = –30 to +75°C*3)
Clock Characteristics
Item
Symbol Min
Typ
Max
Unit
External External clock frequency
clock
External clock duty
operation
External clock rise time
f cp
125
250
350
kHz
11
Duty
45
50
55
%
11
t rcp
—
—
0.2
µs
11
t fcp
—
—
0.2
µs
11
190
270
350
kHz
External clock fall time
Rf
Clock oscillation frequency f OSC
oscillation
Note:
*
Test Condition Notes*
Rf = 91 kΩ
VCC = 5.0 V
12
Refer to the Electrical Characteristics Notes section following these tables.
Bus Timing Characteristics
Write Operation
Item
Symbol
Min
Typ
Max
Unit
Test Condition
Enable cycle time
t cycE
500
—
—
ns
Figure 25
Enable pulse width (high level)
PWEH
230
—
—
Enable rise/fall time
t Er, t Ef
—
—
20
Address set-up time (RS, R/W to E) t AS
40
—
—
Address hold time
t AH
10
—
—
Data set-up time
t DSW
80
—
—
Data hold time
tH
10
—
—
Item
Symbol
Min
Typ
Max
Unit
Test Condition
Enable cycle time
t cycE
500
—
—
ns
Figure 26
Enable pulse width (high level)
PWEH
230
—
—
Enable rise/fall time
t Er, t Ef
—
—
20
Address set-up time (RS, R/W to E) t AS
40
—
—
Address hold time
t AH
10
—
—
Data delay time
t DDR
—
—
160
Data hold time
t DHR
5
—
—
Read Operation
52
HD44780U
Interface Timing Characteristics with External Driver
Item
Symbol
Min
Typ
Max
Unit
Test Condition
High level
t CWH
800
—
—
ns
Figure 27
Low level
t CWL
800
—
—
Clock set-up time
t CSU
500
—
—
Data set-up time
t SU
300
—
—
Data hold time
t DH
300
—
—
M delay time
t DM
–1000
—
1000
Clock rise/fall time
t ct
—
—
100
Clock pulse width
Power Supply Conditions Using Internal Reset Circuit
Item
Symbol
Min
Typ
Max
Unit
Test Condition
Power supply rise time
t rCC
0.1
—
10
ms
Figure 28
Power supply off time
t OFF
1
—
—
53
HD44780U
Electrical Characteristics Notes
1. All voltage values are referred to GND = 0 V.
VCC
B
V1
A = VCC –V5
B = VCC –V1
A ≥ 1.5 V
B ≤ 0.25 × A
A
V5
2.
3.
4.
5.
The conditions of V1 and V5 voltages are for proper
operation of the LSI and not for the LCD output level.
The LCD drive voltage condition for the LCD output
level is specified as LCD voltage VLCD.
VCC ≥ V1 ≥ V2 ≥ V3 ≥ V4 ≥ V5 must be maintained.
For die products, specified at 75°C.
For die products, specified by the die shipment specification.
The following four circuits are I/O pin configurations except for liquid crystal display output.
Input pin
Pin: E (MOS without pull-up)
Output pin
Pins: CL1, CL2, M, D
Pins: RS, R/W (MOS with pull-up)
VCC
VCC
PMOS
PMOS
VCC
PMOS
PMOS
NMOS
NMOS
(pull up MOS)
NMOS
I/O Pin
Pins: DB0 –DB7
(MOS with pull-up)
VCC
(pull-up MOS)
VCC
(input circuit)
PMOS
PMOS
Input enable
NMOS
VCC
NMOS
PMOS
Output enable
Data
NMOS
(output circuit)
(tristate)
54
HD44780U
6. Applies to input pins and I/O pins, excluding the OSC1 pin.
7. Applies to I/O pins.
8. Applies to output pins.
9. Current flowing through pull–up MOSs, excluding output drive MOSs.
10. Input/output current is excluded. When input is at an intermediate level with CMOS, the excessive
current flows through the input circuit to the power supply. To avoid this from happening, the input
level must be fixed high or low.
11. Applies only to external clock operation.
Th
Oscillator
Open
Tl
OSC1
0.7 VCC
0.5 VCC
0.3 VCC
OSC2
t rcp
Duty =
t fcp
Th
× 100%
Th + Tl
12. Applies only to the internal oscillator operation using oscillation resistor Rf.
OSC1
Rf
OSC2
R f : 75 k Ω ± 2% (when VCC = 3 V)
R f : 91 k Ω ± 2% (when VCC = 5 V)
Since the oscillation frequency varies depending on the OSC1 and
OSC2 pin capacitance, the wiring length to these pins should be minimized.
VCC = 3 V
500
400
400
300
(270)
max.
200
typ.
f OSC (kHz)
f OSC (kHz)
VCC = 5 V
500
300
(270)
max.
200
typ.
min.
100
50
(91)100
R f (k Ω)
150
100
50
(75)
100
min.
150
R f (k Ω)
55
HD44780U
13. RCOM is the resistance between the power supply pins (VCC, V1, V4, V5) and each common signal pin
(COM1 to COM16).
RSEG is the resistance between the power supply pins (VCC, V2, V3, V5) and each segment signal pin
(SEG1 to SEG40).
14. The following graphs show the relationship between operation frequency and current consumption.
VCC = 3 V
1.8
1.6
1.6
1.4
1.4
1.2
1.2
1.0
max.
0.8
typ.
0.6
ICC (mA)
ICC (mA)
VCC = 5 V
1.8
1.0
0.8
0.6
0.4
0.4
0.2
0.2
0.0
0
100
200
300
fOSC or fcp (kHz)
400
500
max.
typ.
0.0
0
100
200
300
400
500
fOSC or fcp (kHz)
15. Applies to the OSC1 pin.
16. Each COM and SEG output voltage is within ±0.15 V of the LCD voltage (V CC, V1, V2, V3, V4, V5)
when there is no load.
56
HD44780U
Load Circuits
Data Bus DB0 to DB7
VCC = 5 V
For VCC = 4.5 to 5.5 V
For VCC = 2.7 to 4.5 V
3.9 k Ω
Test
point
Test
point
90 pF
11 k Ω
IS2074 H
diodes
50 pF
External Driver Control Signals: CL1, CL2, D, M
Test
point
30 pF
57
HD44780U
Timing Characteristics
VIH1
VIL1
RS
VIH1
VIL1
tAS
R/W
tAH
VIL1
VIL1
PWEH
tAH
tEf
VIH1
VIL1
E
VIH1
VIL1
tEr
tH
tDSW
VIH1
VIL1
DB0 to DB7
VIL1
VIH1
VIL1
Valid data
tcycE
Figure 25 Write Operation
VIH1
VIL1
RS
VIH1
VIL1
tAS
tAH
VIH1
R/W
VIH1
PWEH
tAH
tEf
VIH1
VIL1
E
VIH1
VIL1
VIL1
tEr
tDHR
tDDR
DB0 to DB7
VOH1
VOL1 *
Valid data
tcycE
Note:
* VOL1 is assumed to be 0.8 V at 2 MHz operation.
Figure 26 Read Operation
58
VOH1
* VOL1
HD44780U
tct
VOH2
CL1
VOH2
VOL2
tCWH
tCSU
CL2
tCWH
VOH2
VOL2
tCWL
tct
tCSU
VOH2
VOL2
D
tDH
tSU
VOH2
M
t DM
Figure 27 Interface Timing with External Driver
VCC
2.7 V/4.5 V*2
0.2 V
0.2 V
0.2 V
tOFF*1
trcc
0.1 ms ≤ trcc ≤ 10 ms
tOFF ≥ 1 ms
Notes: 1. tOFF compensates for the power oscillation period caused by momentary power supply
oscillations.
2. Specified at 4.5 V for 5-V operation, and at 2.7 V for 3-V operation.
3. For if 4.5 V is not reached during 5-V operation, the internal reset circuit will not operate
normally.
In this case, the LSI must be initialized by software. (Refer to the Initializing by
Instruction section.)
Figure 28 Internal Power Supply Reset
59