MICROCHIP PIC18F2515

PIC18F2X1X/4X1X
Data Sheet
28/40/44-Pin Flash Microcontrollers
with 10-Bit A/D and nanoWatt Technology
 2004 Microchip Technology Inc.
Preliminary
DS39636A
Note the following details of the code protection feature on Microchip devices:
•
Microchip products meet the specification contained in their particular Microchip Data Sheet.
•
Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the
intended manner and under normal conditions.
•
There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our
knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data
Sheets. Most likely, the person doing so is engaged in theft of intellectual property.
•
Microchip is willing to work with the customer who is concerned about the integrity of their code.
•
Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not
mean that we are guaranteeing the product as “unbreakable.”
Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our
products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts
allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.
Information contained in this publication regarding device
applications and the like is intended through suggestion only
and may be superseded by updates. It is your responsibility to
ensure that your application meets with your specifications.
No representation or warranty is given and no liability is
assumed by Microchip Technology Incorporated with respect
to the accuracy or use of such information, or infringement of
patents or other intellectual property rights arising from such
use or otherwise. Use of Microchip’s products as critical
components in life support systems is not authorized except
with express written approval by Microchip. No licenses are
conveyed, implicitly or otherwise, under any intellectual
property rights.
Trademarks
The Microchip name and logo, the Microchip logo, Accuron,
dsPIC, KEELOQ, microID, MPLAB, PIC, PICmicro, PICSTART,
PRO MATE, PowerSmart, rfPIC, and SmartShunt are
registered trademarks of Microchip Technology Incorporated
in the U.S.A. and other countries.
AmpLab, FilterLab, MXDEV, MXLAB, PICMASTER, SEEVAL,
SmartSensor and The Embedded Control Solutions Company
are registered trademarks of Microchip Technology
Incorporated in the U.S.A.
Analog-for-the-Digital Age, Application Maestro, dsPICDEM,
dsPICDEM.net, dsPICworks, ECAN, ECONOMONITOR,
FanSense, FlexROM, fuzzyLAB, In-Circuit Serial
Programming, ICSP, ICEPIC, Migratable Memory, MPASM,
MPLIB, MPLINK, MPSIM, PICkit, PICDEM, PICDEM.net,
PICLAB, PICtail, PowerCal, PowerInfo, PowerMate,
PowerTool, rfLAB, rfPICDEM, Select Mode, Smart Serial,
SmartTel and Total Endurance are trademarks of Microchip
Technology Incorporated in the U.S.A. and other countries.
SQTP is a service mark of Microchip Technology Incorporated
in the U.S.A.
All other trademarks mentioned herein are property of their
respective companies.
© 2004, Microchip Technology Incorporated, Printed in the
U.S.A., All Rights Reserved.
Printed on recycled paper.
Microchip received ISO/TS-16949:2002 quality system certification for
its worldwide headquarters, design and wafer fabrication facilities in
Chandler and Tempe, Arizona and Mountain View, California in
October 2003. The Company’s quality system processes and
procedures are for its PICmicro® 8-bit MCUs, KEELOQ® code hopping
devices, Serial EEPROMs, microperipherals, nonvolatile memory and
analog products. In addition, Microchip’s quality system for the design
and manufacture of development systems is ISO 9001:2000 certified.
DS39636A-page ii
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
28/40/44-Pin Flash Microcontrollers with
10-bit A/D and nanoWatt Technology
Power Managed Modes:
Flexible Oscillator Structure:
•
•
•
•
•
•
•
•
• Four Crystal modes, up to 40 MHz
• 4x Phase Lock Loop (PLL) – available for crystal
and internal oscillators
• Two External RC modes, up to 4 MHz
• Two External Clock modes, up to 40 MHz
• Internal oscillator block:
- 8 user selectable frequencies, from 31 kHz to 8 MHz
- Provides a complete range of clock speeds
from 31 kHz to 32 MHz when used with PLL
- User tunable to compensate for frequency drift
• Secondary oscillator using Timer1 @ 32 kHz
• Fail-Safe Clock Monitor:
- Allows for safe shutdown if peripheral clock stops
Run: CPU on, peripherals on
Idle: CPU off, peripherals on
Sleep: CPU off, peripherals off
Idle mode currents down to 3.0 µA typical
Sleep mode currents down to 20 nA typical
Timer1 Oscillator: 1.8 µA, 32 kHz, 2V
Watchdog Timer: 2.1 µA
Two-Speed Oscillator Start-up
Peripheral Highlights:
• High-current sink/source 25 mA/25 mA
• Up to 2 Capture/Compare/PWM (CCP) modules,
one with Auto-Shutdown (28-pin devices)
• Enhanced Capture/Compare/PWM (ECCP)
module (40/44-pin devices only):
- One, two or four PWM outputs
- Selectable polarity
- Programmable dead time
- Auto-Shutdown and Auto-Restart
• Master Synchronous Serial Port (MSSP) module
supporting 3-wire SPI™ (all 4 modes) and I2C™
Master and Slave Modes
• Enhanced Addressable USART module:
- Supports RS-485, RS-232 and LIN 1.2
- RS-232 operation using internal oscillator
block (no external crystal required)
- Auto-Wake-up on Start bit
- Auto-Baud Detect
• 10-bit, up to 13-channel Analog-to-Digital
Converter module (A/D):
- Auto-acquisition capability
- Conversion available during Sleep
• Dual analog comparators with input multiplexing
• Programmable 16-level High/Low-Voltage
Detection (HLVD) module:
- Supports interrupt on High/Low-Voltage
Detection
 2004 Microchip Technology Inc.
Special Microcontroller Features:
• C compiler optimized architecture:
- Optional extended instruction set designed to
optimize re-entrant code
• 100,000 erase/write cycle Flash program memory
typical
• Three programmable external interrupts
• Four input-change interrupts
• Priority levels for interrupts
• 8 x 8 Single-Cycle Hardware Multiplier
• Extended Watchdog Timer (WDT):
- Programmable period from 4 ms to 131s
• Single-supply 5V In-Circuit Serial
Programming™ (ICSP™) via two pins
• In-Circuit Debug (ICD) via two pins
• Wide operating voltage range: 2.0V to 5.5V
• Programmable Brown-out Reset (BOR) with
software enable option
Preliminary
DS39636A-page 1
PIC18F2X1X/4X1X
EUSART
Data
Memory
Comp.
PIC18F2410
16K
8192
768
25
10
2/0
Y
Y
1
2
1/3
PIC18F2510
32K
16384
1536
25
10
2/0
Y
Y
1
2
1/3
PIC18F2515
48K
24576
3968
25
10
2/0
Y
Y
1
2
1/3
PIC18F2610
64K
32768
3968
25
10
2/0
Y
Y
1
2
1/3
PIC18F4410
16K
8192
768
36
13
1/1
Y
Y
1
2
1/3
PIC18F4510
32K
16384
1536
36
13
1/1
Y
Y
1
2
1/3
PIC18F4515
48K
24576
3968
36
13
1/1
Y
Y
1
2
1/3
PIC18F4610
64K
32768
3968
36
13
1/1
Y
Y
1
2
1/3
Program Memory
Device
MSSP
I/O
Flash
(bytes)
DS39636A-page 2
# Single-Word
Instructions
SRAM
(bytes)
10-bit
A/D (ch)
CCP/ECCP
(PWM)
Preliminary
SPI™
Master
I2C™
Timers
8/16-bit
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
Pin Diagrams
28-pin SPDIP, SOIC
28
27
26
25
24
23
22
21
20
19
18
17
16
15
PIC18F2X1X
1
2
3
4
5
6
7
8
9
10
11
12
13
14
RB7/KBI3/PGD
RB6//KBI2/PGC
RB5/KBI1/PGM
RB4/KBI0/AN11
RB3/AN9/CCP2(1)
RB2/INT2/AN8
RB1/INT1/AN10
RB0/INT0/FLT0/AN12
VDD
VSS
RC7/RX/DT
RC6/TX/CK
RC5/SDO
RC4/SDI/SDA
RA1/AN1
RA0/AN0
MCLR/VPP/RE3
RB7/KBI3/PGD
RB6/KBI2/PGC
RB5/KBI1/PGM
RB4KBI0/AN11
MCLR/VPP/RE3
RA0/AN0
RA1/AN1
RA2/AN2/VREF-/CVREF
RA3/AN3/VREF+
RA4/T0CKI/C1OUT
RA5/AN4/SS/HLVDIN/C2OUT
VSS
OSC1/CLKI/RA7
OSC2/CLKO/RA6
RC0/T1OSO/T13CKI
RC1/T1OSI/CCP2(1)
RC2/CCP1
RC3/SCK/SCL
28-pin QFN
28 27 26 25 24 23 22
RA2/AN2/VREF-/CVREF
RA3/AN3/VREF+
RA4/T0CKI/C1OUT
RA5/AN4/SS/HLVDIN/C2OUT
VSS
OSC1/CLKI/RA7
OSC2/CLKO/RA6
1
2
3
4
5
6
7
PIC18F2410
PIC18F2510
21
20
19
18
17
16
15
RB3/AN9/CCP2(1)
RB2/INT2/AN8
RB1/INT1/AN10
RB0/INT0/FLT0/AN12
VDD
VSS
RC7/RX/DT
RC0/T1OSO/T13CKI
RC1/T1OSI/CCP2(1)
RC2/CCP1
RC3/SCK/SCL
RC4/SDI/SDA
RC5/SDO
RC6/TX/CK
8 9 10 11 12 13 14
MCLR/VPP/RE3
RA0/AN0
RA1/AN1
RA2/AN2/VREF-/CVREF
RA3/AN3/VREF+
RA4/T0CKI/C1OUT
RA5/AN4/SS/HLVDIN/C2OUT
RE0/RD/AN5
RE1/WR/AN6
RE2/CS/AN7
VDD
VSS
OSC1/CLKI/RA7
OSC2/CLKO/RA6
RC0/T1OSO/T13CKI
RC1/T1OSI/CCP2(1)
RC2/CCP1/P1A
RC3/SCK/SCL
RD0/PSP0
RD1/PSP1
Note
1:
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
PIC18F4X1X
40-pin PDIP
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
RB7/KBI3/PGD
RB6/KBI2/PGC
RB5/KBI1/PGM
RB4/KBI0/AN11
RB3/AN9/CCP2(1)
RB2/INT2/AN8
RB1/INT1/AN10
RB0/INT0/FLT0/AN12
VDD
VSS
RD7/PSP7/P1D
RD6/PSP6/P1C
RD5/PSP5/P1B
RD4/PSP4
RC7/RX/DT
RC6/TX/CK
RC5/SDO
RC4/SDI/SDA
RD3/PSP3
RD2/PSP2
RB3 is the alternate pin for CCP2 multiplexing.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 3
PIC18F2X1X/4X1X
RC6/TX/CK
RC5/SDO
RC4/SDI/SDA
RD3/PSP3
RD2/PSP2
RD1/PSP1
RD0/PSP0
RC3/SCK/SCL
RC2/CCP1/P1A
RC1/T1OSI/CCP2(1)
NC
Pin Diagrams (Cont.’d)
44
43
42
41
40
39
38
37
36
35
34
44-pin TQFP
PIC18F4X1X
33
32
31
30
29
28
27
26
25
24
23
NC
RC0/T1OSO/T13CKI
OSC2/CLKO/RA6
OSC1/CLKI/RA7
VSS
VDD
RE2/CS/AN7
RE1/WR/AN6
RE0/RD/AN5
RA5/AN4/SS/HLVDIN/C2OUT
RA4/T0CKI/C1OUT
12
13
14
15
16
17
18
19
20
21
22
1
2
3
4
5
6
7
8
9
10
11
RC6/TX/CK
RC5/SDO
RC4/SDI/SDA
RD3/PSP3
RD2/PSP2
RD1/PSP1
RD0/PSP0
RC3/SCK/SCL
RC2/CCP1/P1A
RC1/T1OSI/CCP2(1)
RC0/T1OSO/T13CKI
NC
NC
RB4/KBI0/AN11
RB5/KBI1/PGM
RB6/KBI2/PGC
RB7/KBI3/PGD
MCLR/VPP/RE3
RA0/AN0
RA1/AN1
RA2/AN2/VREF-/CVREF
RA3/AN3/VREF+
RC7/RX/DT
RD4/PSP4
RD5/PSP5/P1B
RD6/PSP6/P1C
RD7/PSP7/P1D
VSS
VDD
RB0/INT0/FLT0/AN12
RB1/INT1/AN10
RB2/INT2/AN8
RB3/AN9/CCP2(1)
44
43
42
41
40
39
38
37
36
35
34
44-pin QFN
PIC18F4X1X
33
32
31
30
29
28
27
26
25
24
23
OSC2/CLKO/RA6
OSC1/CLKI/RA7
VSS
VSS
VDD
VDD
RE2/CS/AN7
RE1/WR/AN6
RE0/RD/AN5
RA5/AN4/SS/HLVDIN/C2OUT
RA4/T0CKI/C1OUT
12
13
14
15
16
17
18
19
20
21
22
1
2
3
4
5
6
7
8
9
10
11
RB3/AN9/CCP2(1)
NC
RB4/KBI0/AN11
RB5/KBI1/PGM
RB6/KBI2/PGC
RB7/KBI3/PGD
MCLR/VPP/RE3
RA0/AN0
RA1/AN1
RA2/AN2/VREF-/CVREF
RA3/AN3/VREF+
RC7/RX/DT
RD4/PSP4
RD5/PSP5/P1B
RD6/PSP6/P1C
RD7/PSP7/P1D
VSS
VDD
VDD
RB0/INT0/FLT0/AN12
RB1/INT1/AN10
RB2/INT2/AN8
Note
DS39636A-page 4
1:
RB3 is the alternate pin for CCP2 multiplexing.
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
Table of Contents
1.0 Device Overview .......................................................................................................................................................................... 7
2.0 Oscillator Configurations ............................................................................................................................................................ 23
3.0 Power Managed Modes ............................................................................................................................................................. 33
4.0 Reset .......................................................................................................................................................................................... 41
5.0 Memory Organization ................................................................................................................................................................. 53
6.0 Flash Program Memory.............................................................................................................................................................. 75
7.0 8 x 8 Hardware Multiplier............................................................................................................................................................ 79
8.0 Interrupts .................................................................................................................................................................................... 81
9.0 I/O Ports ..................................................................................................................................................................................... 95
10.0 Timer0 Module ......................................................................................................................................................................... 113
11.0 Timer1 Module ......................................................................................................................................................................... 117
12.0 Timer2 Module ......................................................................................................................................................................... 123
13.0 Timer3 Module ......................................................................................................................................................................... 125
14.0 Capture/Compare/PWM (CCP) Modules ................................................................................................................................. 129
15.0 Enhanced Capture/Compare/PWM (ECCP) Module................................................................................................................ 137
16.0 Master Synchronous Serial Port (MSSP) Module .................................................................................................................... 151
17.0 Enhanced Universal Synchronous Receiver Transmitter (EUSART)....................................................................................... 191
18.0 10-Bit Analog-to-Digital Converter (A/D) Module ..................................................................................................................... 211
19.0 Comparator Module.................................................................................................................................................................. 221
20.0 Comparator Voltage Reference Module................................................................................................................................... 227
21.0 High/Low-Voltage Detect (HLVD)............................................................................................................................................. 231
22.0 Special Features of the CPU.................................................................................................................................................... 237
23.0 Instruction Set Summary .......................................................................................................................................................... 257
24.0 Development Support............................................................................................................................................................... 307
25.0 Electrical Characteristics .......................................................................................................................................................... 313
26.0 DC and AC Characteristics Graphs And Tables ...................................................................................................................... 351
27.0 Packaging Information.............................................................................................................................................................. 353
Appendix A: Revision History............................................................................................................................................................. 361
Appendix B: Device Differences ........................................................................................................................................................ 361
Appendix C: Conversion Considerations ........................................................................................................................................... 362
Appendix D: Migration From Baseline to Enhanced Devices ............................................................................................................ 362
Appendix E: Migration From Mid-Range to Enhanced Devices ......................................................................................................... 363
Appendix F: Migration From High-End to Enhanced Devices............................................................................................................ 363
Index ................................................................................................................................................................................................. 365
On-Line Support................................................................................................................................................................................. 375
Systems Information and Upgrade Hot Line ...................................................................................................................................... 375
Reader Response .............................................................................................................................................................................. 376
PIC18F2X1X/4X1X Product Identification System............................................................................................................................. 377
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 5
PIC18F2X1X/4X1X
TO OUR VALUED CUSTOMERS
It is our intention to provide our valued customers with the best documentation possible to ensure successful use of your Microchip
products. To this end, we will continue to improve our publications to better suit your needs. Our publications will be refined and
enhanced as new volumes and updates are introduced.
If you have any questions or comments regarding this publication, please contact the Marketing Communications Department via
E-mail at [email protected] or fax the Reader Response Form in the back of this data sheet to (480) 792-4150.
We welcome your feedback.
Most Current Data Sheet
To obtain the most up-to-date version of this data sheet, please register at our Worldwide Web site at:
http://www.microchip.com
You can determine the version of a data sheet by examining its literature number found on the bottom outside corner of any page.
The last character of the literature number is the version number, (e.g., DS30000A is version A of document DS30000).
Errata
An errata sheet, describing minor operational differences from the data sheet and recommended workarounds, may exist for current
devices. As device/documentation issues become known to us, we will publish an errata sheet. The errata will specify the revision
of silicon and revision of document to which it applies.
To determine if an errata sheet exists for a particular device, please check with one of the following:
• Microchip’s Worldwide Web site; http://www.microchip.com
• Your local Microchip sales office (see last page)
• The Microchip Corporate Literature Center; U.S. FAX: (480) 792-7277
When contacting a sales office or the literature center, please specify which device, revision of silicon and data sheet (include
literature number) you are using.
Customer Notification System
Register on our Web site at www.microchip.com/cn to receive the most current information on all of our products.
DS39636A-page 6
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
1.0
DEVICE OVERVIEW
1.1.2
This document contains device specific information for
the following devices:
• PIC18F2410
• PIC18LF2410
• PIC18F2510
• PIC18LF2510
• PIC18F2515
• PIC18LF2515
• PIC18F2610
• PIC18LF2610
• PIC18F4410
• PIC18LF4410
• PIC18F4510
• PIC18LF4510
• PIC18F4515
• PIC18LF4515
• PIC18F4610
• PIC18LF4610
This family offers the advantages of all PIC18
microcontrollers – namely, high computational
performance at an economical price – with the addition
of high-endurance, Flash program memory. On top of
these features, the PIC18F2X1X/4X1X family introduces
design enhancements that make these microcontrollers
a logical choice for many high-performance, power
sensitive applications.
1.1
1.1.1
New Core Features
nanoWatt TECHNOLOGY
All of the devices in the PIC18F2X1X/4X1X family
incorporate a range of features that can significantly
reduce power consumption during operation. Key
items include:
• Alternate Run Modes: By clocking the controller
from the Timer1 source or the internal oscillator
block, power consumption during code execution
can be reduced by as much as 90%.
• Multiple Idle Modes: The controller can also run
with its CPU core disabled but the peripherals still
active. In these states, power consumption can be
reduced even further, to as little as 4% of normal
operation requirements.
• On-the-fly Mode Switching: The power
managed modes are invoked by user code during
operation, allowing the user to incorporate powersaving ideas into their application’s software
design.
• Lower Consumption in Key Modules: The
power requirements for both Timer1 and the
Watchdog Timer have been minimized. See
Section 25.0 “Electrical Characteristics” for
values.
 2004 Microchip Technology Inc.
MULTIPLE OSCILLATOR OPTIONS
AND FEATURES
All of the devices in the PIC18F2X1X/4X1X family offer
ten different oscillator options, allowing users a wide
range of choices in developing application hardware.
These include:
• Four Crystal modes, using crystals or ceramic
resonators
• Two External Clock modes, offering the option of
using two pins (oscillator input and a divide-by-4
clock output) or one pin (oscillator input, with the
second pin reassigned as general I/O)
• Two External RC Oscillator modes with the same
pin options as the External Clock modes
• An internal oscillator block which provides an
8 MHz clock and an INTRC source (approximately 31 kHz), as well as a range of 6 user
selectable clock frequencies, between 125 kHz to
4 MHz, for a total of 8 clock frequencies. This
option frees the two oscillator pins for use as
additional general purpose I/O.
• A Phase Lock Loop (PLL) frequency multiplier,
available to both the high-speed crystal and
internal oscillator modes, which allows clock
speeds of up to 40 MHz. Used with the internal
oscillator, the PLL gives users a complete selection
of clock speeds, from 31 kHz to 32 MHz – all
without using an external crystal or clock circuit.
Besides its availability as a clock source, the internal
oscillator block provides a stable reference source that
gives the family additional features for robust
operation:
• Fail-Safe Clock Monitor: This option constantly
monitors the main clock source against a
reference signal provided by the internal
oscillator. If a clock failure occurs, the controller is
switched to the internal oscillator block, allowing
for continued low-speed operation or a safe
application shutdown.
• Two-Speed Start-up: This option allows the
internal oscillator to serve as the clock source
from Power-on Reset, or wake-up from Sleep
mode, until the primary clock source is available.
Preliminary
DS39636A-page 7
PIC18F2X1X/4X1X
1.2
Other Special Features
1.3
• Memory Endurance: The Flash cells for program
memory are rated to 100,000 erase/write cycles.
Data retention without refresh is conservatively
estimated to be greater than 40 years.
• Extended Instruction Set: The PIC18F2X1X/
4X1X family introduces an optional extension to
the PIC18 instruction set, which adds 8 new
instructions and an Indexed Addressing mode.
This extension, enabled as a device configuration
option, has been specifically designed to optimize
re-entrant application code originally developed in
high-level languages, such as C.
• Enhanced CCP Module: In PWM mode, this
module provides 1, 2 or 4 modulated outputs for
controlling half-bridge and full-bridge drivers.
Other features include Auto-Shutdown, for
disabling PWM outputs on interrupt or other select
conditions and Auto-Restart, to reactivate outputs
once the condition has cleared.
• Enhanced Addressable USART: This serial
communication module is capable of standard
RS-232 operation and provides support for the LIN
bus protocol. Other enhancements include automatic baud rate detection and a 16-bit Baud Rate
Generator for improved resolution. When the
microcontroller is using the internal oscillator
block, the USART provides stable operation for
applications that talk to the outside world without
using an external crystal (or its accompanying
power requirement).
• 10-bit A/D Converter: This module incorporates
programmable acquisition time, allowing for a
channel to be selected and a conversion to be
initiated without waiting for a sampling period and
thus, reduce code overhead.
• Extended Watchdog Timer (WDT): This
enhanced version incorporates a 16-bit prescaler,
allowing an extended time-out range that is stable
across operating voltage and temperature. See
Section 25.0 “Electrical Characteristics” for
time-out periods.
DS39636A-page 8
Details on Individual Family
Members
Devices in the PIC18F2X1X/4X1X family are available
in 28-pin and 40/44-pin packages. Block diagrams for
the two groups are shown in Figure 1-1 and Figure 1-2.
The devices are differentiated from each other in five
ways:
1.
2.
3.
4.
5.
Flash program memory
• 16 Kbytes for PIC18F2410/4410 devices
• 32 Kbytes for PIC18F2510/4510 devices
• 48 Kbytes for PIC18F2515/4515 devices
• 64 Kbytes for PIC18F2610/4610 devices
A/D channels (10 for 28-pin devices, 13 for
40/44-pin devices).
I/O ports (3 bidirectional ports on 28-pin devices,
5 bidirectional ports on 40/44-pin devices).
CCP and Enhanced CCP implementation (28-pin
devices have 2 standard CCP modules; 40/44-pin
devices have one standard CCP module and one
ECCP module).
Parallel Slave Port (present only on 40/44-pin
devices).
All other features for devices in this family are identical.
These are summarized in Table 1-1.
The pinouts for all devices are listed in Table 1-3 and
Table 1-4.
Like all Microchip PIC18 devices, members of the
PIC18F2X1X/4X1X family are available as both
standard and low-voltage devices. Standard devices
with Flash memory, designated with an “F” in the part
number (such as PIC18F2610), accommodate an
operating VDD range of 4.2V to 5.5V. Low-voltage
parts, designated by “LF” (such as PIC18LF2610),
function over an extended VDD range of 2.0V to 5.5V.
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
TABLE 1-1:
DEVICE FEATURES (PIC18F2410/2510/2515/2610)
Features
PIC18F2410
PIC18F2510
PIC18F2515
PIC18F2610
Operating Frequency
DC – 40 MHz
DC – 40 MHz
DC – 40 MHz
DC – 40 MHz
Program Memory (Bytes)
16384
32768
49152
65536
Program Memory
(Instructions)
8192
16384
24576
32768
Data Memory (Bytes)
768
1536
3968
3968
Interrupt Sources
I/O Ports
18
18
18
18
Ports A, B, C, (E)
Ports A, B, C, (E)
Ports A, B, C, (E)
Ports A, B, C, (E)
Timers
4
4
4
4
Capture/Compare/PWM Modules
2
2
2
2
Enhanced
Capture/Compare/PWM Modules
0
0
0
0
MSSP,
Enhanced USART
MSSP,
Enhanced USART
MSSP,
Enhanced USART
MSSP,
Enhanced USART
Serial Communications
Parallel Communications (PSP)
No
No
No
No
10-bit Analog-to-Digital Module
10 Input Channels
10 Input Channels
10 Input Channels
10 Input Channels
Resets (and Delays)
POR, BOR,
RESET Instruction,
Stack Full,
Stack Underflow
(PWRT, OST),
MCLR (optional),
WDT
POR, BOR,
RESET Instruction,
Stack Full,
Stack Underflow
(PWRT, OST),
MCLR (optional),
WDT
POR, BOR,
RESET Instruction,
Stack Full,
Stack Underflow
(PWRT, OST),
MCLR (optional),
WDT
POR, BOR,
RESET Instruction,
Stack Full,
Stack Underflow
(PWRT, OST),
MCLR (optional),
WDT
Programmable
High/Low-Voltage Detect
Yes
Yes
Yes
Yes
Programmable
Brown-out Reset
Yes
Yes
Yes
Yes
Instruction Set
Packages
 2004 Microchip Technology Inc.
75 Instructions;
75 Instructions;
75 Instructions;
75 Instructions;
83 with Extended
83 with Extended
83 with Extended
83 with Extended
Instruction Set enabled Instruction Set enabled Instruction Set enabled Instruction Set enabled
28-pin SPDIP
28-pin SOIC
28-pin QFN
28-pin SPDIP
28-pin SOIC
28-pin QFN
Preliminary
28-pin SPDIP
28-pin SOIC
28-pin SPDIP
28-pin SOIC
DS39636A-page 9
PIC18F2X1X/4X1X
TABLE 1-2:
DEVICE FEATURES (PIC18F4410/4510/4515/4610)
Features
PIC18F4410
PIC18F4510
PIC18F4515
PIC18F4610
Operating Frequency
DC – 40 MHz
DC – 40 MHz
DC – 40 MHz
DC – 40 MHz
Program Memory (Bytes)
16384
32768
49152
65536
Program Memory
(Instructions)
8192
16384
24576
32768
768
1536
3968
3968
Data Memory (Bytes)
Interrupt Sources
I/O Ports
19
19
19
19
Ports A, B, C, D, E
Ports A, B, C, D, E
Ports A, B, C, D, E
Ports A, B, C, D, E
Timers
4
4
4
4
Capture/Compare/PWM Modules
1
1
1
1
Enhanced
Capture/Compare/PWM Modules
1
1
1
1
MSSP,
Enhanced USART
MSSP,
Enhanced USART
MSSP,
Enhanced USART
MSSP,
Enhanced USART
Serial Communications
Parallel Communications (PSP)
Yes
Yes
Yes
Yes
10-bit Analog-to-Digital Module
13 Input Channels
13 Input Channels
13 Input Channels
13 Input Channels
Resets (and Delays)
POR, BOR,
RESET Instruction,
Stack Full,
Stack Underflow
(PWRT, OST),
MCLR (optional),
WDT
POR, BOR,
RESET Instruction,
Stack Full,
Stack Underflow
(PWRT, OST),
MCLR (optional),
WDT
POR, BOR,
RESET Instruction,
Stack Full,
Stack Underflow
(PWRT, OST),
MCLR (optional),
WDT
POR, BOR,
RESET Instruction,
Stack Full,
Stack Underflow
(PWRT, OST),
MCLR (optional),
WDT
Programmable
High/Low-Voltage Detect
Yes
Yes
Yes
Yes
Programmable
Brown-out Reset
Yes
Yes
Yes
Yes
Instruction Set
Packages
DS39636A-page 10
75 Instructions;
75 Instructions;
75 Instructions;
75 Instructions;
83 with Extended
83 with Extended
83 with Extended
83 with Extended
Instruction Set enabled Instruction Set enabled Instruction Set enabled Instruction Set enabled
40-pin PDIP
44-pin QFN
44-pin TQFP
40-pin PDIP
44-pin QFN
44-pin TQFP
Preliminary
40-pin PDIP
44-pin QFN
44-pin TQFP
40-pin PDIP
44-pin QFN
44-pin TQFP
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
FIGURE 1-1:
PIC18F2410/2510/2515/2610 (28-PIN) BLOCK DIAGRAM
Data Bus<8>
Table Pointer<21>
PCLATU PCLATH
21
PORTA
Data Latch
Data Memory
(.7, 1.5, 3.9
Kbytes)
8
8
inc/dec logic
RA0/AN0
RA1/AN1
RA2/AN2/VREF-/CVREF
RA3/AN3/VREF+
RA4/T0CKI/C1OUT
RA5/AN4/SS/HLVDIN/C2OUT
OSC2/CLKO(3)/RA6
OSC1/CLKI(3)/RA7
Address Latch
20
PCU PCH PCL
Program Counter
12
Data Address<12>
31 Level Stack
Address Latch
Program Memory
(16/32/48/64
Kbytes)
Data Latch
4
BSR
STKPTR
4
Access
Bank
12
FSR0
FSR1
FSR2
12
PORTB
RB0/INT0/FLT0/AN12
RB1/INT1/AN10
RB2/INT2/AN8
RB3/AN9/CCP2(1)
RB4/KBI0/AN11
RB5/KBI1/PGM
RB6/KBI2/PGC
RB7/KBI3/PGD
inc/dec
logic
8
Table Latch
Address
Decode
ROM Latch
Instruction Bus <16>
IR
8
Instruction
Decode and
Control
State Machine
Control Signals
PRODH PRODL
PORTC
3
8
W
BITOP
8
OSC1(3)
Internal
Oscillator
Block
(3)
OSC2
T1OSI
INTRC
Oscillator
T1OSO
8 MHz
Oscillator
VDD, VSS
BOR
HLVD
Comparator
CCP1
8
8
8
8
ALU<8>
8
Watchdog
Timer
Brown-out
Reset
Fail-Safe
Clock Monitor
Single-Supply
Programming
In-Circuit
Debugger
MCLR(2)
Note
Power-up
Timer
Oscillator
Start-up Timer
Power-on
Reset
RC0/T1OSO/T13CKI
RC1/T1OSI/CCP2(1)
RC2/CCP1
RC3/SCK/SCL
RC4/SDI/SDA
RC5/SDO
RC6/TX/CK
RC7/RX/DT
8 x 8 Multiply
Precision
Band Gap
Reference
PORTE
MCLR/VPP/RE3(2)
Timer0
Timer1
Timer2
Timer3
CCP2
MSSP
EUSART
ADC
10-bit
1:
CCP2 is multiplexed with RC1 when configuration bit CCP2MX is set, or RB3 when CCP2MX is not set.
2:
RE3 is only available when MCLR functionality is disabled.
3:
OSC1/CLKI and OSC2/CLKO are only available in select oscillator modes and when these pins are not being used as digital I/O.
Refer to Section 2.0 “Oscillator Configurations” for additional information.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 11
PIC18F2X1X/4X1X
FIGURE 1-2:
PIC18F4410/4510/4515/4610 (40/44-PIN) BLOCK DIAGRAM
Data Bus<8>
PORTA
Table Pointer<21>
PCLATU PCLATH
21
RA0/AN0
RA1/AN1
RA2/AN2/VREF-/CVREF
RA3/AN3/VREF+
RA4/T0CKI/C1OUT
RA5/AN4/SS/HLVDIN/C2OUT
OSC2/CLKO(3)/RA6
OSC1/CLKI(3)/RA7
Data Latch
Data Memory
(.7, 1.5, 3.9
Kbytes)
8
8
inc/dec logic
Address Latch
20
PCU PCH PCL
Program Counter
12
Data Address<12>
PORTB
31 Level Stack
Address Latch
Program Memory
(16/32/48/64
Kbytes)
Data Latch
4
BSR
STKPTR
12
FSR0
FSR1
FSR2
RB0/INT0/FLT0/AN12
RB1/INT1/AN10
RB2/INT2/AN8
RB3/AN9/CCP2(1)
RB4/KBI0/AN11
RB5/KBI1/PGM
RB6/KBI2/PGC
RB7/KBI3/PGD
4
Access
Bank
12
inc/dec
logic
8
Table Latch
PORTC
Address
Decode
ROM Latch
Instruction Bus <16>
RC0/T1OSO/T13CKI
RC1/T1OSI/CCP2(1)
RC2/CCP1/P1A
RC3/SCK/SCL
RC4/SDI/SDA
RC5/SDO
RC6/TX/CK
RC7/RX/DT
IR
8
State Machine
Control Signals
Instruction
Decode and
Control
PRODH PRODL
3
8 x 8 Multiply
8
W
BITOP
8
OSC1(3)
Internal
Oscillator
Block
OSC2(3)
INTRC
Oscillator
T1OSI
MCLR(2)
Single-Supply
Programming
VDD, VSS
In-Circuit
Debugger
BOR
HLVD
Comparator
ECCP1
ALU<8>
8
Watchdog
Timer
Brown-out
Reset
Fail-Safe
Clock Monitor
RD0/PSP0:RD4/PSP4
RD5/PSP5/P1B
RD6/PSP6/P1C
RD7/PSP7/P1D
8
8
8
Power-on
Reset
8 MHz
Oscillator
T1OSO
Note
Power-up
Timer
Oscillator
Start-up Timer
8
PORTD
PORTE
RE0/RD/AN5
RE1/WR/AN6
RE2/CS/AN7
MCLR/VPP/RE3(2)
Precision
Band Gap
Reference
Timer0
Timer1
Timer2
Timer3
CCP2
MSSP
EUSART
ADC
10-bit
1:
CCP2 is multiplexed with RC1 when configuration bit CCP2MX is set, or RB3 when CCP2MX is not set.
2:
RE3 is only available when MCLR functionality is disabled.
3:
OSC1/CLKI and OSC2/CLKO are only available in select oscillator modes and when these pins are not being used as digital I/O.
Refer to Section 2.0 “Oscillator Configurations” for additional information.
DS39636A-page 12
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
TABLE 1-3:
PIC18F2410/2510/2515/2610 PINOUT I/O DESCRIPTIONS
Pin Number
Pin Name
MCLR/VPP/RE3
MCLR
Pin Buffer
SPDIP,
Type
Type
QFN
SOIC
1
26
VPP
RE3
OSC1/CLKI/RA7
OSC1
9
6
I
ST
P
I
ST
ST
O
—
CLKO
O
—
RA6
I/O
TTL
RA7
OSC2/CLKO/RA6
OSC2
10
Master Clear (input) or programming voltage (input).
Master Clear (Reset) input. This pin is an active-low
Reset to the device.
Programming voltage input.
Digital input.
Oscillator crystal or external clock input.
Oscillator crystal input or external clock source input.
ST buffer when configured in RC mode; CMOS otherwise.
I CMOS
External clock source input. Always associated with pin
function OSC1. (See related OSC1/CLKI, OSC2/CLKO
pins.)
I/O
TTL
General purpose I/O pin.
I
CLKI
Description
7
Oscillator crystal or clock output.
Oscillator crystal output. Connects to crystal or
resonator in Crystal Oscillator mode.
In RC mode, OSC2 pin outputs CLKO, which has 1/4 the
frequency of OSC1 and denotes the instruction cycle rate.
General purpose I/O pin.
Legend: TTL = TTL compatible input
CMOS = CMOS compatible input or output
ST = Schmitt Trigger input with CMOS levels I
= Input
O
= Output
P
= Power
Note 1: Default assignment for CCP2 when configuration bit CCP2MX is set.
2: Alternate assignment for CCP2 when configuration bit CCP2MX is cleared.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 13
PIC18F2X1X/4X1X
TABLE 1-3:
PIC18F2410/2510/2515/2610 PINOUT I/O DESCRIPTIONS (CONTINUED)
Pin Number
Pin Name
Pin Buffer
SPDIP,
Type
Type
QFN
SOIC
Description
PORTA is a bidirectional I/O port.
RA0/AN0
RA0
AN0
2
RA1/AN1
RA1
AN1
3
RA2/AN2/VREF-/CVREF
RA2
AN2
VREFCVREF
4
RA3/AN3/VREF+
RA3
AN3
VREF+
5
RA4/T0CKI/C1OUT
RA4
T0CKI
C1OUT
6
RA5/AN4/SS/HLVDIN/
C2OUT
RA5
AN4
SS
HLVDIN
C2OUT
7
27
I/O
TTL
I Analog
Digital I/O.
Analog input 0.
I/O
TTL
I Analog
Digital I/O.
Analog input 1.
I/O
TTL
I Analog
I Analog
O Analog
Digital I/O.
Analog input 2.
A/D reference voltage (low) input.
Comparator reference voltage output.
I/O
TTL
I Analog
I Analog
Digital I/O.
Analog input 3.
A/D reference voltage (high) input.
I/O
I
O
Digital I/O.
Timer0 external clock input.
Comparator 1 output.
28
1
2
3
ST
ST
—
4
I/O
TTL
I Analog
I
TTL
I Analog
O
—
Digital I/O.
Analog input 4.
SPI™ slave select input.
High/Low-Voltage Detect input.
Comparator 2 output.
RA6
See the OSC2/CLKO/RA6 pin.
RA7
See the OSC1/CLKI/RA7 pin.
Legend: TTL = TTL compatible input
CMOS = CMOS compatible input or output
ST = Schmitt Trigger input with CMOS levels I
= Input
O
= Output
P
= Power
Note 1: Default assignment for CCP2 when configuration bit CCP2MX is set.
2: Alternate assignment for CCP2 when configuration bit CCP2MX is cleared.
DS39636A-page 14
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
TABLE 1-3:
PIC18F2410/2510/2515/2610 PINOUT I/O DESCRIPTIONS (CONTINUED)
Pin Number
Pin Name
Pin Buffer
SPDIP,
Type
Type
QFN
SOIC
Description
PORTB is a bidirectional I/O port. PORTB can be software
programmed for internal weak pull-ups on all inputs.
RB0/INT0/FLT0/AN12
RB0
INT0
FLT0
AN12
21
RB1/INT1/AN10
RB1
INT1
AN10
22
RB2/INT2/AN8
RB2
INT2
AN8
23
RB3/AN9/CCP2
RB3
AN9
CCP2(1)
24
RB4/KBI0/AN11
RB4
KBI0
AN11
25
RB5/KBI1/PGM
RB5
KBI1
PGM
26
RB6/KBI2/PGC
RB6
KBI2
PGC
27
RB7/KBI3/PGD
RB7
KBI3
PGD
28
18
I/O
TTL
I
ST
I
ST
I Analog
Digital I/O.
External interrupt 0.
PWM Fault input for CCP1.
Analog input 12.
19
I/O
TTL
I
ST
I Analog
Digital I/O.
External interrupt 1.
Analog input 10.
I/O
TTL
I
ST
I Analog
Digital I/O.
External interrupt 2.
Analog input 8.
I/O
TTL
I Analog
I/O
ST
Digital I/O.
Analog input 9.
Capture 2 input/Compare 2 output/PWM 2 output.
I/O
TTL
I
TTL
I Analog
Digital I/O.
Interrupt-on-change pin.
Analog input 11.
I/O
I
I/O
TTL
TTL
ST
Digital I/O.
Interrupt-on-change pin.
Low-Voltage ICSP™ Programming enable pin.
I/O
I
I/O
TTL
TTL
ST
Digital I/O.
Interrupt-on-change pin.
In-Circuit Debugger and ICSP programming clock pin.
I/O
I
I/O
TTL
TTL
ST
Digital I/O.
Interrupt-on-change pin.
In-Circuit Debugger and ICSP programming data pin.
20
21
22
23
24
25
Legend: TTL = TTL compatible input
CMOS = CMOS compatible input or output
ST = Schmitt Trigger input with CMOS levels I
= Input
O
= Output
P
= Power
Note 1: Default assignment for CCP2 when configuration bit CCP2MX is set.
2: Alternate assignment for CCP2 when configuration bit CCP2MX is cleared.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 15
PIC18F2X1X/4X1X
TABLE 1-3:
PIC18F2410/2510/2515/2610 PINOUT I/O DESCRIPTIONS (CONTINUED)
Pin Number
Pin Name
Pin Buffer
SPDIP,
Type
Type
QFN
SOIC
Description
PORTC is a bidirectional I/O port.
RC0/T1OSO/T13CKI
RC0
T1OSO
T13CKI
11
RC1/T1OSI/CCP2
RC1
T1OSI
CCP2(2)
12
RC2/CCP1
RC2
CCP1
13
RC3/SCK/SCL
RC3
SCK
SCL
14
RC4/SDI/SDA
RC4
SDI
SDA
15
RC5/SDO
RC5
SDO
16
RC6/TX/CK
RC6
TX
CK
17
RC7/RX/DT
RC7
RX
DT
18
RE3
—
VSS
VDD
8
I/O
O
I
ST
—
ST
Digital I/O.
Timer1 oscillator output.
Timer1/Timer3 external clock input.
9
I/O
ST
I Analog
I/O
ST
Digital I/O.
Timer1 oscillator input.
Capture 2 input/Compare 2 output/PWM 2 output.
I/O
I/O
ST
ST
Digital I/O.
Capture 1 input/Compare 1 output/PWM 1 output.
I/O
I/O
I/O
ST
ST
ST
Digital I/O.
Synchronous serial clock input/output for SPI™ mode.
Synchronous serial clock input/output for I2C™ mode.
I/O
I
I/O
ST
ST
ST
Digital I/O.
SPI data in.
I2C data I/O.
I/O
O
ST
—
Digital I/O.
SPI data out.
I/O
O
I/O
ST
—
ST
Digital I/O.
EUSART asynchronous transmit.
EUSART synchronous clock (see related RX/DT).
I/O
I
I/O
ST
ST
ST
Digital I/O.
EUSART asynchronous receive.
EUSART synchronous data (see related TX/CK).
—
—
—
See MCLR/VPP/RE3 pin.
8, 19
5, 16
P
—
Ground reference for logic and I/O pins.
20
17
P
—
Positive supply for logic and I/O pins.
10
11
12
13
14
15
Legend: TTL = TTL compatible input
CMOS = CMOS compatible input or output
ST = Schmitt Trigger input with CMOS levels I
= Input
O
= Output
P
= Power
Note 1: Default assignment for CCP2 when configuration bit CCP2MX is set.
2: Alternate assignment for CCP2 when configuration bit CCP2MX is cleared.
DS39636A-page 16
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
TABLE 1-4:
PIC18F4410/4510/4515/4610 PINOUT I/O DESCRIPTIONS
Pin Number
Pin Name
PDIP
MCLR/VPP/RE3
MCLR
1
Pin Buffer
Type
Type
QFN TQFP
18
18
VPP
RE3
OSC1/CLKI/RA7
OSC1
13
32
ST
P
I
ST
30
I
CLKI
I
RA7
OSC2/CLKO/RA6
OSC2
I
I/O
14
33
Description
Master Clear (input) or programming voltage (input).
Master Clear (Reset) input. This pin is an active-low
Reset to the device.
Programming voltage input.
Digital input.
Oscillator crystal or external clock input.
Oscillator crystal input or external clock source input.
ST buffer when configured in RC mode;
analog otherwise.
CMOS
External clock source input. Always associated with
pin function OSC1. (See related OSC1/CLKI,
OSC2/CLKO pins.)
TTL
General purpose I/O pin.
ST
31
O
—
CLKO
O
—
RA6
I/O
TTL
Oscillator crystal or clock output.
Oscillator crystal output. Connects to crystal
or resonator in Crystal Oscillator mode.
In RC mode, OSC2 pin outputs CLKO, which
has 1/4 the frequency of OSC1 and denotes
the instruction cycle rate.
General purpose I/O pin.
Legend: TTL = TTL compatible input
CMOS = CMOS compatible input or output
ST = Schmitt Trigger input with CMOS levels I
= Input
O
= Output
P
= Power
Note 1: Default assignment for CCP2 when configuration bit CCP2MX is set.
2: Alternate assignment for CCP2 when configuration bit CCP2MX is cleared.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 17
PIC18F2X1X/4X1X
TABLE 1-4:
PIC18F4410/4510/4515/4610 PINOUT I/O DESCRIPTIONS (CONTINUED)
Pin Number
Pin Name
PDIP
Pin Buffer
Type
Type
QFN TQFP
Description
PORTA is a bidirectional I/O port.
RA0/AN0
RA0
AN0
2
RA1/AN1
RA1
AN1
3
RA2/AN2/VREF-/CVREF
RA2
AN2
VREFCVREF
4
RA3/AN3/VREF+
RA3
AN3
VREF+
5
RA4/T0CKI/C1OUT
RA4
T0CKI
C1OUT
6
RA5/AN4/SS/HLVDIN/
C2OUT
RA5
AN4
SS
HLVDIN
C2OUT
7
19
20
21
22
23
24
19
I/O
I
TTL
Analog
Digital I/O.
Analog input 0.
I/O
I
TTL
Analog
Digital I/O.
Analog input 1.
I/O
I
I
O
TTL
Analog
Analog
Analog
Digital I/O.
Analog input 2.
A/D reference voltage (low) input.
Comparator reference voltage output.
I/O
I
I
TTL
Analog
Analog
Digital I/O.
Analog input 3.
A/D reference voltage (high) input.
I/O
I
O
ST
ST
—
I/O
I
I
I
O
TTL
Analog
TTL
Analog
—
20
21
22
23
Digital I/O.
Timer0 external clock input.
Comparator 1 output.
24
Digital I/O.
Analog input 4.
SPI™ slave select input.
High/Low-Voltage Detect input.
Comparator 2 output.
RA6
See the OSC2/CLKO/RA6 pin.
RA7
See the OSC1/CLKI/RA7 pin.
Legend: TTL = TTL compatible input
CMOS = CMOS compatible input or output
ST = Schmitt Trigger input with CMOS levels I
= Input
O
= Output
P
= Power
Note 1: Default assignment for CCP2 when configuration bit CCP2MX is set.
2: Alternate assignment for CCP2 when configuration bit CCP2MX is cleared.
DS39636A-page 18
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
TABLE 1-4:
PIC18F4410/4510/4515/4610 PINOUT I/O DESCRIPTIONS (CONTINUED)
Pin Number
Pin Name
PDIP
Pin Buffer
QFN TQFP Type Type
Description
PORTB is a bidirectional I/O port. PORTB can be
software programmed for internal weak pull-ups on all
inputs.
RB0/INT0/FLT0/AN12
RB0
INT0
FLT0
AN12
33
RB1/INT1/AN10
RB1
INT1
AN10
34
RB2/INT2/AN8
RB2
INT2
AN8
35
RB3/AN9/CCP2
RB3
AN9
CCP2(1)
36
RB4/KBI0/AN11
RB4
KBI0
AN11
37
RB5/KBI1/PGM
RB5
KBI1
PGM
38
RB6/KBI2/PGC
RB6
KBI2
PGC
39
RB7/KBI3/PGD
RB7
KBI3
PGD
40
9
10
11
12
14
15
16
17
8
I/O
I
I
I
TTL
ST
ST
Analog
Digital I/O.
External interrupt 0.
PWM Fault input for Enhanced CCP1.
Analog input 12.
I/O
I
I
TTL
ST
Analog
Digital I/O.
External interrupt 1.
Analog input 10.
I/O
I
I
TTL
ST
Analog
Digital I/O.
External interrupt 2.
Analog input 8.
I/O
I
I/O
TTL
Analog
ST
Digital I/O.
Analog input 9.
Capture 2 input/Compare 2 output/PWM 2 output.
I/O
I
I
TTL
TTL
Analog
Digital I/O.
Interrupt-on-change pin.
Analog input 11.
I/O
I
I/O
TTL
TTL
ST
Digital I/O.
Interrupt-on-change pin.
Low-Voltage ICSP™ Programming enable pin.
I/O
I
I/O
TTL
TTL
ST
Digital I/O.
Interrupt-on-change pin.
In-Circuit Debugger and ICSP programming
clock pin.
I/O
I
I/O
TTL
TTL
ST
Digital I/O.
Interrupt-on-change pin.
In-Circuit Debugger and ICSP programming
data pin.
9
10
11
14
15
16
17
Legend: TTL = TTL compatible input
CMOS = CMOS compatible input or output
ST = Schmitt Trigger input with CMOS levels I
= Input
O
= Output
P
= Power
Note 1: Default assignment for CCP2 when configuration bit CCP2MX is set.
2: Alternate assignment for CCP2 when configuration bit CCP2MX is cleared.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 19
PIC18F2X1X/4X1X
TABLE 1-4:
PIC18F4410/4510/4515/4610 PINOUT I/O DESCRIPTIONS (CONTINUED)
Pin Number
Pin Name
PDIP
Pin Buffer
Type
Type
QFN TQFP
Description
PORTC is a bidirectional I/O port.
RC0/T1OSO/T13CKI
RC0
T1OSO
T13CKI
15
RC1/T1OSI/CCP2
RC1
T1OSI
CCP2(2)
16
RC2/CCP1/P1A
RC2
CCP1
P1A
17
RC3/SCK/SCL
RC3
SCK
18
34
35
36
37
32
23
RC5/SDO
RC5
SDO
24
RC6/TX/CK
RC6
TX
CK
25
RC7/RX/DT
RC7
RX
DT
26
42
43
44
1
ST
—
ST
I/O
I
I/O
ST
CMOS
ST
I/O
I/O
O
ST
ST
—
Digital I/O.
Capture1 input/Compare1 output/PWM1 output.
Enhanced CCP1 output.
I/O
I/O
ST
ST
I/O
ST
Digital I/O.
Synchronous serial clock input/output for
SPI™ mode.
Synchronous serial clock input/output for I2C™ mode.
I/O
I
I/O
ST
ST
ST
Digital I/O.
SPI data in.
I2C data I/O.
I/O
O
ST
—
Digital I/O.
SPI data out.
I/O
O
I/O
ST
—
ST
Digital I/O.
EUSART asynchronous transmit.
EUSART synchronous clock (see related RX/DT).
I/O
I
I/O
ST
ST
ST
Digital I/O.
EUSART asynchronous receive.
EUSART synchronous data (see related TX/CK).
Digital I/O.
Timer1 oscillator output.
Timer1/Timer3 external clock input.
35
Digital I/O.
Timer1 oscillator input.
Capture 2 input/Compare 2 output/PWM 2 output.
36
37
SCL
RC4/SDI/SDA
RC4
SDI
SDA
I/O
O
I
42
43
44
1
Legend: TTL = TTL compatible input
CMOS = CMOS compatible input or output
ST = Schmitt Trigger input with CMOS levels I
= Input
O
= Output
P
= Power
Note 1: Default assignment for CCP2 when configuration bit CCP2MX is set.
2: Alternate assignment for CCP2 when configuration bit CCP2MX is cleared.
DS39636A-page 20
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
TABLE 1-4:
PIC18F4410/4510/4515/4610 PINOUT I/O DESCRIPTIONS (CONTINUED)
Pin Number
Pin Name
PDIP
Pin Buffer
QFN TQFP Type Type
Description
PORTD is a bidirectional I/O port or a Parallel Slave
Port (PSP) for interfacing to a microprocessor port.
These pins have TTL input buffers when PSP module
is enabled.
RD0/PSP0
RD0
PSP0
19
RD1/PSP1
RD1
PSP1
20
RD2/PSP2
RD2
PSP2
21
RD3/PSP3
RD3
PSP3
22
RD4/PSP4
RD4
PSP4
27
RD5/PSP5/P1B
RD5
PSP5
P1B
28
RD6/PSP6/P1C
RD6
PSP6
P1C
29
RD7/PSP7/P1D
RD7
PSP7
P1D
30
38
39
40
41
2
3
4
5
38
I/O
I/O
ST
TTL
Digital I/O.
Parallel Slave Port data.
I/O
I/O
ST
TTL
Digital I/O.
Parallel Slave Port data.
I/O
I/O
ST
TTL
Digital I/O.
Parallel Slave Port data.
I/O
I/O
ST
TTL
Digital I/O.
Parallel Slave Port data.
I/O
I/O
ST
TTL
Digital I/O.
Parallel Slave Port data.
I/O
I/O
O
ST
TTL
—
Digital I/O.
Parallel Slave Port data.
Enhanced CCP1 output.
I/O
I/O
O
ST
TTL
—
Digital I/O.
Parallel Slave Port data.
Enhanced CCP1 output.
I/O
I/O
O
ST
TTL
—
Digital I/O.
Parallel Slave Port data.
Enhanced CCP1 output.
39
40
41
2
3
4
5
Legend: TTL = TTL compatible input
CMOS = CMOS compatible input or output
ST = Schmitt Trigger input with CMOS levels I
= Input
O
= Output
P
= Power
Note 1: Default assignment for CCP2 when configuration bit CCP2MX is set.
2: Alternate assignment for CCP2 when configuration bit CCP2MX is cleared.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 21
PIC18F2X1X/4X1X
TABLE 1-4:
PIC18F4410/4510/4515/4610 PINOUT I/O DESCRIPTIONS (CONTINUED)
Pin Number
Pin Name
PDIP
Pin Buffer
Type
Type
QFN TQFP
Description
PORTE is a bidirectional I/O port.
RE0/RD/AN5
RE0
RD
8
25
25
I/O
I
ST
TTL
I
Analog
I/O
I
ST
TTL
I
Analog
I/O
I
ST
TTL
I
Analog
—
—
—
See MCLR/VPP/RE3 pin.
6, 29
P
—
Ground reference for logic and I/O pins.
7, 8, 7, 28
28, 29
P
—
Positive supply for logic and I/O pins.
—
—
No connect.
AN5
RE1/WR/AN6
RE1
WR
9
26
26
AN6
RE2/CS/AN7
RE2
CS
10
27
—
—
VSS
12, 31 6, 30,
31
VDD
11, 32
NC
—
13
Digital I/O.
Write control for Parallel Slave Port
(see CS and RD pins).
Analog input 6.
27
AN7
RE3
Digital I/O.
Read control for Parallel Slave Port
(see also WR and CS pins).
Analog input 5.
12, 13,
33, 34
Digital I/O.
Chip select control for Parallel Slave Port
(see related RD and WR).
Analog input 7.
Legend: TTL = TTL compatible input
CMOS = CMOS compatible input or output
ST = Schmitt Trigger input with CMOS levels I
= Input
O
= Output
P
= Power
Note 1: Default assignment for CCP2 when configuration bit CCP2MX is set.
2: Alternate assignment for CCP2 when configuration bit CCP2MX is cleared.
DS39636A-page 22
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
2.0
OSCILLATOR
CONFIGURATIONS
2.1
Oscillator Types
FIGURE 2-1:
C1(1)
PIC18F2X1X/4X1X devices can be operated in ten
different oscillator modes. The user can program the
configuration bits, FOSC3:FOSC0, in Configuration
Register 1H to select one of these ten modes:
1.
2.
3.
4.
Low-Power Crystal
Crystal/Resonator
High-Speed Crystal/Resonator
High-Speed Crystal/Resonator
with PLL enabled
5. RC
External Resistor/Capacitor with
FOSC/4 output on RA6
6. RCIO
External Resistor/Capacitor with I/O
on RA6
7. INTIO1 Internal Oscillator with FOSC/4 output
on RA6 and I/O on RA7
8. INTIO2 Internal Oscillator with I/O on RA6
and RA7
9. EC
External Clock with FOSC/4 output
10. ECIO
External Clock with I/O on RA6
C2(1)
Sleep
PIC18FXXXX
OSC2
Note 1:
See Table 2-1 and Table 2-2 for initial values of
C1 and C2.
2:
A series resistor (RS) may be required for AT
strip cut crystals.
3:
RF varies with the oscillator mode chosen.
TABLE 2-1:
CAPACITOR SELECTION FOR
CERAMIC RESONATORS
Typical Capacitor Values Used:
Mode
Freq
OSC1
OSC2
XT
3.58 MHz
4.19 MHz
4 MHz
4 MHz
15 pF
15 pF
30 pF
50 pF
15 pF
15 pF
30 pF
50 pF
Crystal Oscillator/Ceramic
Resonators
The oscillator design requires the use of a parallel cut
crystal.
Use of a series cut crystal may give a
frequency out of the crystal manufacturer’s
specifications.
Capacitor values are for design guidance only.
Different capacitor values may be required to produce
acceptable oscillator operation. The user should test
the performance of the oscillator over the expected
VDD and temperature range for the application.
See the notes following Table 2-2 for additional
information.
Note:
 2004 Microchip Technology Inc.
To
Internal
Logic
RF(3)
RS(2)
In XT, LP, HS or HSPLL Oscillator modes, a crystal or
ceramic resonator is connected to the OSC1 and
OSC2 pins to establish oscillation. Figure 2-1 shows
the pin connections.
Note:
OSC1
XTAL
LP
XT
HS
HSPLL
2.2
CRYSTAL/CERAMIC
RESONATOR OPERATION
(XT, LP, HS OR HSPLL
CONFIGURATION)
Preliminary
When using resonators with frequencies
above 3.5 MHz, the use of HS mode,
rather than XT mode, is recommended.
HS mode may be used at any VDD for
which the controller is rated. If HS is
selected, it is possible that the gain of the
oscillator will overdrive the resonator.
Therefore, a series resistor should be
placed between the OSC2 pin and the
resonator. As a good starting point, the
recommended value of RS is 330Ω.
DS39636A-page 23
PIC18F2X1X/4X1X
TABLE 2-2:
Osc Type
CAPACITOR SELECTION FOR
CRYSTAL OSCILLATOR
Crystal
Freq
Typical Capacitor Values
Tested:
C1
C2
LP
32 kHz
30 pF
30 pF
XT
1 MHz
4 MHz
15 pF
15 pF
15 pF
15 pF
HS
4 MHz
10 MHz
20 MHz
25 MHz
15 pF
15 pF
15 pF
15 pF
15 pF
15 pF
15 pF
15 pF
An external clock source may also be connected to the
OSC1 pin in the HS mode, as shown in Figure 2-2.
FIGURE 2-2:
EXTERNAL CLOCK INPUT
OPERATION
(HS OSCILLATOR
CONFIGURATION)
OSC1
Clock from
Ext. System
PIC18FXXXX
Open
(HS Mode)
OSC2
Capacitor values are for design guidance only.
Different capacitor values may be required to produce
acceptable oscillator operation. The user should test
the performance of the oscillator over the expected
VDD and temperature range for the application.
See the notes following this table for additional
information.
Note 1: Higher capacitance increases the stability
of the oscillator but also increases the
start-up time.
2: When operating below 3V VDD, or when
using certain ceramic resonators at any
voltage, it may be necessary to use the
HS mode or switch to a crystal oscillator.
3: Since each resonator/crystal has its own
characteristics, the user should consult
the resonator/crystal manufacturer for
appropriate
values
of
external
components.
4: Rs may be required to avoid overdriving
crystals with low drive level specification.
5: Always verify oscillator performance over
the VDD and temperature range that is
expected for the application.
2.3
External Clock Input
The EC and ECIO Oscillator modes require an external
clock source to be connected to the OSC1 pin. There is
no oscillator start-up time required after a Power-on
Reset or after an exit from Sleep mode.
In the EC Oscillator mode, the oscillator frequency
divided by 4 is available on the OSC2 pin. This signal
may be used for test purposes or to synchronize other
logic. Figure 2-3 shows the pin connections for the EC
Oscillator mode.
FIGURE 2-3:
OSC1/CLKI
Clock from
Ext. System
PIC18FXXXX
FOSC/4
OSC2/CLKO
The ECIO Oscillator mode functions like the EC mode,
except that the OSC2 pin becomes an additional
general purpose I/O pin. The I/O pin becomes bit 6 of
PORTA (RA6). Figure 2-4 shows the pin connections
for the ECIO Oscillator mode.
FIGURE 2-4:
PIC18FXXXX
RA6
Preliminary
EXTERNAL CLOCK
INPUT OPERATION
(ECIO CONFIGURATION)
OSC1/CLKI
Clock from
Ext. System
DS39636A-page 24
EXTERNAL CLOCK
INPUT OPERATION
(EC CONFIGURATION)
I/O (OSC2)
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
2.4
RC Oscillator
2.5
For timing insensitive applications, the “RC” and
“RCIO” device options offer additional cost savings.
The actual oscillator frequency is a function of several
factors:
• supply voltage
• values of the external resistor (REXT) and
capacitor (CEXT)
• operating temperature
A Phase Locked Loop (PLL) circuit is provided as an
option for users who wish to use a lower frequency
oscillator circuit or to clock the device up to its highest
rated frequency from a crystal oscillator. This may be
useful for customers who are concerned with EMI due
to high-frequency crystals or users who require higher
clock speeds from an internal oscillator.
2.5.1
Given the same device, operating voltage and temperature and component values, there will also be unit-to-unit
frequency variations. These are due to factors such as:
• normal manufacturing variation
• difference in lead frame capacitance between
package types (especially for low CEXT values)
• variations within the tolerance of limits of REXT
and CEXT
HSPLL OSCILLATOR MODE
The HSPLL mode makes use of the HS mode oscillator
for frequencies up to 10 MHz. A PLL then multiplies the
oscillator output frequency by 4 to produce an internal
clock frequency up to 40 MHz. The PLLEN bit is not
available in this oscillator mode.
The PLL is only available to the crystal oscillator when
the FOSC3:FOSC0 configuration bits are programmed
for HSPLL mode (= 0110).
In the RC Oscillator mode, the oscillator frequency
divided by 4 is available on the OSC2 pin. This signal
may be used for test purposes or to synchronize other
logic. Figure 2-5 shows how the R/C combination is
connected.
FIGURE 2-5:
PLL Frequency Multiplier
FIGURE 2-7:
PLL BLOCK DIAGRAM
(HS MODE)
HS Oscillator Enable
PLL Enable
(from Configuration Register 1H)
RC OSCILLATOR MODE
VDD
OSC2
HS Mode
OSC1 Crystal
Osc
REXT
OSC1
Internal
Clock
FIN
FOUT
Loop
Filter
CEXT
PIC18FXXXX
VSS
FOSC/4
OSC2/CLKO
÷4
The RCIO Oscillator mode (Figure 2-6) functions like
the RC mode, except that the OSC2 pin becomes an
additional general purpose I/O pin. The I/O pin
becomes bit 6 of PORTA (RA6).
RCIO OSCILLATOR MODE
VDD
REXT
OSC1
VCO
MUX
Recommended values: 3 kΩ ≤ REXT ≤ 100 kΩ
CEXT > 20 pF
FIGURE 2-6:
Phase
Comparator
Internal
Clock
2.5.2
SYSCLK
PLL AND INTOSC
The PLL is also available to the internal oscillator block
in selected oscillator modes. In this configuration, the
PLL is enabled in software and generates a clock
output of up to 32 MHz. The operation of INTOSC with
the PLL is described in Section 2.6.4 “PLL in INTOSC
Modes”.
CEXT
PIC18FXXXX
VSS
RA6
I/O (OSC2)
Recommended values: 3 kΩ ≤ REXT ≤ 100 kΩ
CEXT > 20 pF
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 25
PIC18F2X1X/4X1X
2.6
Internal Oscillator Block
The PIC18F2X1X/4X1X devices include an internal
oscillator block which generates two different clock
signals; either can be used as the microcontroller’s
clock source. This may eliminate the need for external
oscillator circuits on the OSC1 and/or OSC2 pins.
The main output (INTOSC) is an 8 MHz clock source,
which can be used to directly drive the device clock. It
also drives a postscaler, which can provide a range of
clock frequencies from 31 kHz to 4 MHz. The INTOSC
output is enabled when a clock frequency from 125 kHz
to 8 MHz is selected.
The other clock source is the internal RC oscillator
(INTRC), which provides a nominal 31 kHz output.
INTRC is enabled if it is selected as the device clock
source; it is also enabled automatically when any of the
following are enabled:
•
•
•
•
Power-up Timer
Fail-Safe Clock Monitor
Watchdog Timer
Two-Speed Start-up
These features are discussed in greater detail in
Section 22.0 “Special Features of the CPU”.
The clock source frequency (INTOSC direct, INTRC
direct or INTOSC postscaler) is selected by configuring
the IRCF bits of the OSCCON register (page 30).
2.6.1
INTIO MODES
Using the internal oscillator as the clock source eliminates the need for up to two external oscillator pins,
which can then be used for digital I/O. Two distinct
configurations are available:
• In INTIO1 mode, the OSC2 pin outputs FOSC/4,
while OSC1 functions as RA7 for digital input and
output.
• In INTIO2 mode, OSC1 functions as RA7 and
OSC2 functions as RA6, both for digital input and
output.
2.6.2
INTOSC OUTPUT FREQUENCY
The internal oscillator block is calibrated at the factory
to produce an INTOSC output frequency of 8.0 MHz.
The INTRC oscillator operates independently of the
INTOSC source. Any changes in INTOSC across
voltage and temperature are not necessarily reflected
by changes in INTRC and vice versa.
2.6.3
OSCTUNE REGISTER
The internal oscillator’s output has been calibrated at
the factory but can be adjusted in the user’s application. This is done by writing to the OSCTUNE register
(Register 2-1). The tuning sensitivity is constant
throughout the tuning range.
DS39636A-page 26
When the OSCTUNE register is modified, the INTOSC
frequency will begin shifting to the new frequency. The
INTRC clock will reach the new frequency within
8 clock cycles (approximately 8 * 32 µs = 256 µs). The
INTOSC clock will stabilize within 1 ms. Code execution continues during this shift. There is no indication
that the shift has occurred.
The OSCTUNE register also implements the INTSRC
and PLLEN bits, which control certain features of the
internal oscillator block. The INTSRC bit allows users
to select which internal oscillator provides the clock
source when the 31 kHz frequency option is selected.
This is covered in greater detail in Section 2.7.1
“Oscillator Control Register”.
The PLLEN bit controls the operation of the frequency
multiplier, PLL, in internal oscillator modes.
2.6.4
PLL IN INTOSC MODES
The 4x frequency multiplier can be used with the
internal oscillator block to produce faster device clock
speeds than are normally possible with an internal
oscillator. When enabled, the PLL produces a clock
speed of up to 32 MHz.
Unlike HSPLL mode, the PLL is controlled through
software. The control bit, PLLEN (OSCTUNE<6>), is
used to enable or disable its operation.
The PLL is available when the device is configured to
use the internal oscillator block as its primary clock
source (FOSC3:FOSC0 = 1001 or 1000). Additionally,
the PLL will only function when the selected output frequency is either 4 MHz or 8 MHz (OSCCON<6:4> = 111
or 110). If both of these conditions are not met, the PLL
is disabled.
The PLLEN control bit is only functional in those
internal oscillator modes where the PLL is available. In
all other modes, it is forced to ‘0’ and is effectively
unavailable.
2.6.5
INTOSC FREQUENCY DRIFT
The factory calibrates the internal oscillator block
output (INTOSC) for 8 MHz. However, this frequency
may drift as VDD or temperature changes, which can
affect the controller operation in a variety of ways. It is
possible to adjust the INTOSC frequency by modifying
the value in the OSCTUNE register. This has no effect
on the INTRC clock source frequency.
Tuning the INTOSC source requires knowing when to
make the adjustment, in which direction it should be
made and in some cases, how large a change is
needed. Three compensation techniques are
discussed in Section 2.6.5.1 “Compensating with
the USART”, Section 2.6.5.2 “Compensating with
the Timers” and Section 2.6.5.3 “Compensating
with the CCP Module in Capture Mode”, but other
techniques may be used.
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
REGISTER 2-1:
OSCTUNE: OSCILLATOR TUNING REGISTER
R/W-0
R/W-0(1)
U-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
INTSRC
PLLEN(1)
—
TUN4
TUN3
TUN2
TUN1
TUN0
bit 7
bit 0
bit 7
INTSRC: Internal Oscillator Low-Frequency Source Select bit
1 = 31.25 kHz device clock derived from 8 MHz INTOSC source (divide-by-256 enabled)
0 = 31 kHz device clock derived directly from INTRC internal oscillator
bit 6
PLLEN: Frequency Multiplier PLL for INTOSC Enable bit(1)
1 = PLL enabled for INTOSC (4 MHz and 8 MHz only)
0 = PLL disabled
Note 1: Available only in certain oscillator configurations; otherwise, this bit is unavailable
and reads as ‘0’. See Section 2.6.4 “PLL in INTOSC Modes” for details.
bit 5
Unimplemented: Read as ‘0’
bit 4-0
TUN4:TUN0: Frequency Tuning bits
01111 = Maximum frequency
•
•
•
•
00001
00000 = Center frequency. Oscillator module is running at the calibrated frequency.
11111
•
•
•
•
10000 = Minimum frequency
Legend:
R = Readable bit
-n = Value at POR
2.6.5.1
W = Writable bit
‘1’ = Bit is set
Compensating with the USART
2.6.5.3
An adjustment may be required when the USART
begins to generate framing errors or receives data with
errors while in Asynchronous mode. Framing errors
indicate that the device clock frequency is too high; to
adjust for this, decrement the value in OSCTUNE to
reduce the clock frequency. On the other hand, errors
in data may suggest that the clock speed is too low; to
compensate, increment OSCTUNE to increase the
clock frequency.
2.6.5.2
Compensating with the Timers
This technique compares device clock speed to some
reference clock. Two timers may be used; one timer is
clocked by the peripheral clock, while the other is
clocked by a fixed reference source, such as the
Timer1 oscillator.
Both timers are cleared, but the timer clocked by the
reference generates interrupts. When an interrupt
occurs, the internally clocked timer is read and both
timers are cleared. If the internally clocked timer value
is greater than expected, then the internal oscillator
block is running too fast. To adjust for this, decrement
the OSCTUNE register.
 2004 Microchip Technology Inc.
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
x = Bit is unknown
Compensating with the CCP Module
in Capture Mode
A CCP module can use free running Timer1 (or
Timer3), clocked by the internal oscillator block and an
external event with a known period (i.e., AC power
frequency). The time of the first event is captured in the
CCPRxH:CCPRxL registers and is recorded for use
later. When the second event causes a capture, the
time of the first event is subtracted from the time of the
second event. Since the period of the external event is
known, the time difference between events can be
calculated.
If the measured time is much greater than the calculated time, the internal oscillator block is running too
fast; to compensate, decrement the OSCTUNE register.
If the measured time is much less than the calculated
time, the internal oscillator block is running too slow; to
compensate, increment the OSCTUNE register.
Preliminary
DS39636A-page 27
PIC18F2X1X/4X1X
2.7
Clock Sources and Oscillator
Switching
Like previous PIC18 devices, the PIC18F2X1X/4X1X
family includes a feature that allows the device clock
source to be switched from the main oscillator to an alternate low-frequency clock source. PIC18F2X1X/4X1X
devices offer two alternate clock sources. When an
alternate clock source is enabled, the various power
managed operating modes are available.
Essentially, there are three clock sources for these
devices:
• Primary oscillators
• Secondary oscillators
• Internal oscillator block
PIC18F2X1X/4X1X devices offer the Timer1 oscillator
as a secondary oscillator. This oscillator, in all power
managed modes, is often the time base for functions
such as a real-time clock.
Most often, a 32.768 kHz watch crystal is connected
between the RC0/T1OSO/T13CKI and RC1/T1OSI
pins. Like the LP mode oscillator circuit, loading
capacitors are also connected from each pin to ground.
The Timer1 oscillator is discussed in greater detail in
Section 11.3 “Timer1 Oscillator”.
The primary oscillators include the External Crystal
and Resonator modes, the External RC modes, the
External Clock modes and the internal oscillator block.
The particular mode is defined by the FOSC3:FOSC0
configuration bits. The details of these modes are
covered earlier in this chapter.
FIGURE 2-8:
The secondary oscillators are those external sources
not connected to the OSC1 or OSC2 pins. These
sources may continue to operate even after the
controller is placed in a power managed mode.
In addition to being a primary clock source, the internal
oscillator block is available as a power managed
mode clock source. The INTRC source is also used as
the clock source for several special features, such as
the WDT and Fail-Safe Clock Monitor.
The clock sources for the PIC18F2X1X/4X1X devices
are shown in Figure 2-8. See Section 22.0 “Special
Features of the CPU” for Configuration register details.
PIC18F2X1X/4X1X CLOCK DIAGRAM
PIC18F2X1X/4X1X
Primary Oscillator
LP, XT, HS, RC, EC
OSC2
Sleep
4 x PLL
OSC1
OSCTUNE<6>
Secondary Oscillator
T1OSCEN
Enable
Oscillator
OSCCON<6:4>
8 MHz
OSCCON<6:4>
INTRC
Source
Internal Oscillator
CPU
111
110
2 MHz
31 kHz (INTRC)
1 MHz
500 kHz
250 kHz
125 kHz
IDLEN
101
100
011
MUX
8 MHz
(INTOSC)
Postscaler
Internal
Oscillator
Block
8 MHz
Source
4 MHz
Peripherals
MUX
T1OSC
T1OSO
T1OSI
HSPLL, INTOSC/PLL
010
001
1 31 kHz
000
0
Clock
Control
FOSC3:FOSC0
OSCCON<1:0>
Clock Source Option
for other Modules
OSCTUNE<7>
WDT, PWRT, FSCM
and Two-Speed Start-up
DS39636A-page 28
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
2.7.1
OSCILLATOR CONTROL REGISTER
The OSCCON register (Register 2-2) controls several
aspects of the device clock’s operation, both in full
power operation and in power managed modes.
The System Clock Select bits, SCS1:SCS0, select the
clock source. The available clock sources are the
primary clock (defined by the FOSC3:FOSC0 configuration bits), the secondary clock (Timer1 oscillator) and
the internal oscillator block. The clock source changes
immediately after one or more of the bits is written to,
following a brief clock transition interval. The SCS bits
are cleared on all forms of Reset.
The Internal Oscillator Frequency Select bits
(IRCF2:IRCF0) select the frequency output of the
internal oscillator block to drive the device clock. The
choices are the INTRC source, the INTOSC source
(8 MHz) or one of the frequencies derived from the
INTOSC postscaler (31.25 kHz to 4 MHz). If the
internal oscillator block is supplying the device clock,
changing the states of these bits will have an immediate change on the internal oscillator’s output. On
device Resets, the default output frequency of the
internal oscillator block is set at 1 MHz.
When a nominal output frequency of 31 kHz is selected
(IRCF2:IRCF0 = 000), users may choose which internal oscillator acts as the source. This is done with the
INTSRC bit in the OSCTUNE register (OSCTUNE<7>).
Setting this bit selects INTOSC as a 31.25 kHz clock
source by enabling the divide-by-256 output of the
INTOSC postscaler. Clearing INTSRC selects INTRC
(nominally 31 kHz) as the clock source.
The IDLEN bit determines if the device goes into Sleep
mode or one of the Idle modes when the SLEEP
instruction is executed.
The use of the flag and control bits in the OSCCON
register is discussed in more detail in Section 3.0
“Power Managed Modes”.
Note 1: The Timer1 oscillator must be enabled to
select the secondary clock source. The
Timer1 oscillator is enabled by setting the
T1OSCEN bit in the Timer1 Control register (T1CON<3>). If the Timer1 oscillator
is not enabled, then any attempt to select
a secondary clock source will be ignored.
2: It is recommended that the Timer1
oscillator be operating and stable before
selecting the secondary clock source or a
very long delay may occur while the
Timer1 oscillator starts.
2.7.2
OSCILLATOR TRANSITIONS
PIC18F2X1X/4X1X devices contain circuitry to prevent
clock “glitches” when switching between clock sources.
A short pause in the device clock occurs during the
clock switch. The length of this pause is the sum of two
cycles of the old clock source and three to four cycles
of the new clock source. This formula assumes that the
new clock source is stable.
Clock transitions are discussed in greater detail in
Section 3.1.2 “Entering Power Managed Modes”.
This option allows users to select the tunable and more
precise INTOSC as a clock source, while maintaining
power savings with a very low clock speed. Regardless
of the setting of INTSRC, INTRC always remains the
clock source for features such as the Watchdog Timer
and the Fail-Safe Clock Monitor.
The OSTS, IOFS and T1RUN bits indicate which clock
source is currently providing the device clock. The
OSTS bit indicates that the Oscillator Start-up Timer
has timed out and the primary clock is providing the
device clock in primary clock modes. The IOFS bit
indicates when the internal oscillator block has stabilized and is providing the device clock in RC Clock
modes. The T1RUN bit (T1CON<6>) indicates when
the Timer1 oscillator is providing the device clock in
secondary clock modes. In power managed modes,
only one of these three bits will be set at any time. If
none of these bits are set, the INTRC is providing the
clock or the internal oscillator block has just started and
is not yet stable.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 29
PIC18F2X1X/4X1X
REGISTER 2-2:
OSCCON: OSCILLATOR CONTROL REGISTER
R/W-0
R/W-1
R/W-0
R/W-0
R(1)
R-0
R/W-0
R/W-0
IDLEN
IRCF2
IRCF1
IRCF0
OSTS
IOFS
SCS1
SCS0
bit 7
bit 0
bit 7
IDLEN: Idle Enable bit
1 = Device enters Idle mode on SLEEP instruction
0 = Device enters Sleep mode on SLEEP instruction
bit 6-4
IRCF2:IRCF0: Internal Oscillator Frequency Select bits
111 = 8 MHz (INTOSC drives clock directly)
110 = 4 MHz
101 = 2 MHz
100 = 1 MHz(3)
011 = 500 kHz
010 = 250 kHz
001 = 125 kHz
000 = 31 kHz (from either INTOSC/256 or INTRC directly)(2)
bit 3
OSTS: Oscillator Start-up Time-out Status bit(1)
1 = Oscillator start-up time-out timer has expired; primary oscillator is running
0 = Oscillator start-up time-out timer is running; primary oscillator is not ready
bit 2
IOFS: INTOSC Frequency Stable bit
1 = INTOSC frequency is stable
0 = INTOSC frequency is not stable
bit 1-0
SCS1:SCS0: System Clock Select bits
1x = Internal oscillator block
01 = Secondary (Timer1) oscillator
00 = Primary oscillator
Note 1: Reset state depends on state of the IESO configuration bit.
2: Source selected by the INTSRC bit (OSCTUNE<7>), see text.
3: Default output frequency of INTOSC on Reset.
Legend:
DS39636A-page 30
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
Preliminary
x = Bit is unknown
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
2.8
Effects of Power Managed Modes
on the Various Clock Sources
When PRI_IDLE mode is selected, the designated
primary oscillator continues to run without interruption.
For all other power managed modes, the oscillator
using the OSC1 pin is disabled. The OSC1 pin (and
OSC2 pin, if used by the oscillator) will stop oscillating.
In secondary clock modes (SEC_RUN and
SEC_IDLE), the Timer1 oscillator is operating and
providing the device clock. The Timer1 oscillator may
also run in all power managed modes if required to
clock Timer1 or Timer3.
In internal oscillator modes (RC_RUN and RC_IDLE),
the internal oscillator block provides the device clock
source. The 31 kHz INTRC output can be used directly
to provide the clock and may be enabled to support
various special features, regardless of the power
managed mode (see Section 22.2 “Watchdog Timer
(WDT)”, Section 22.3 “Two-Speed Start-up” and
Section 22.4 “Fail-Safe Clock Monitor” for more
information on WDT, Fail-Safe Clock Monitor and TwoSpeed Start-up). The INTOSC output at 8 MHz may be
used directly to clock the device or may be divided
down by the postscaler. The INTOSC output is disabled
if the clock is provided directly from the INTRC output.
If the Sleep mode is selected, all clock sources are
stopped. Since all the transistor switching currents
have been stopped, Sleep mode achieves the lowest
current consumption of the device (only leakage
currents).
Enabling any on-chip feature that will operate during
Sleep will increase the current consumed during Sleep.
The INTRC is required to support WDT operation. The
Timer1 oscillator may be operating to support a real-
TABLE 2-3:
time clock. Other features may be operating that do not
require a device clock source (i.e., SSP slave, PSP,
INTn pins and others). Peripherals that may add
significant current consumption are listed in
Section 25.2 “DC Characteristics”.
2.9
Power-up Delays
Power-up delays are controlled by two timers, so that
no external Reset circuitry is required for most applications. The delays ensure that the device is kept in
Reset until the device power supply is stable under normal circumstances and the primary clock is operating
and stable. For additional information on power-up
delays, see Section 4.5 “Device Reset Timers”.
The first timer is the Power-up Timer (PWRT), which
provides a fixed delay on power-up (parameter 33,
Table 25-10). It is enabled by clearing (= 0) the
PWRTEN configuration bit.
The second timer is the Oscillator Start-up Timer
(OST), intended to keep the chip in Reset until the
crystal oscillator is stable (LP, XT and HS modes). The
OST does this by counting 1024 oscillator cycles
before allowing the oscillator to clock the device.
When the HSPLL Oscillator mode is selected, the
device is kept in Reset for an additional 2 ms, following
the HS mode OST delay, so the PLL can lock to the
incoming clock frequency.
There is a delay of interval TCSD (parameter 38,
Table 25-10), following POR, while the controller
becomes ready to execute instructions. This delay runs
concurrently with any other delays. This may be the
only delay that occurs when any of the EC, RC or INTIO
modes are used as the primary clock source.
OSC1 AND OSC2 PIN STATES IN SLEEP MODE
Oscillator Mode
OSC1 Pin
OSC2 Pin
RC, INTIO1
Floating, external resistor should pull high
At logic low (clock/4 output)
RCIO
Floating, external resistor should pull high
Configured as PORTA, bit 6
INTIO2
Configured as PORTA, bit 7
Configured as PORTA, bit 6
ECIO
Floating, pulled by external clock
Configured as PORTA, bit 6
EC
Floating, pulled by external clock
At logic low (clock/4 output)
LP, XT and HS
Feedback inverter disabled at quiescent
voltage level
Feedback inverter disabled at quiescent
voltage level
Note:
See Table 4-2 in Section 4.0 “Reset” for time-outs due to Sleep and MCLR Reset.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 31
PIC18F2X1X/4X1X
NOTES:
DS39636A-page 32
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
3.0
POWER MANAGED MODES
3.1.1
The SCS1:SCS0 bits allow the selection of one of three
clock sources for power managed modes. They are:
PIC18F2X1X/4X1X devices offer a total of seven operating modes for more efficient power management.
These modes provide a variety of options for selective
power conservation in applications where resources
may be limited (i.e., battery-powered devices).
• the primary clock, as defined by the
FOSC3:FOSC0 configuration bits
• the secondary clock (the Timer1 oscillator)
• the internal oscillator block (for RC modes)
There are three categories of power managed modes:
• Run modes
• Idle modes
• Sleep mode
3.1.2
The power managed modes include several powersaving features offered on previous PICmicro®
devices. One is the clock switching feature, offered in
other PIC18 devices, allowing the controller to use the
Timer1 oscillator in place of the primary oscillator. Also
included is the Sleep mode, offered by all PICmicro
devices, where all device clocks are stopped.
Entry to the Power Managed Idle or Sleep modes is
triggered by the execution of a SLEEP instruction. The
actual mode that results depends on the status of the
IDLEN bit.
Depending on the current mode and the mode being
switched to, a change to a power managed mode does
not always require setting all of these bits. Many
transitions may be done by changing the oscillator select
bits, or changing the IDLEN bit, prior to issuing a SLEEP
instruction. If the IDLEN bit is already configured
correctly, it may only be necessary to perform a SLEEP
instruction to switch to the desired mode.
Selecting Power Managed Modes
Selecting a power managed mode requires two
decisions: if the CPU is to be clocked or not and the
selection of a clock source. The IDLEN bit
(OSCCON<7>) controls CPU clocking, while the
SCS1:SCS0 bits (OSCCON<1:0>) select the clock
source. The individual modes, bit settings, clock sources
and affected modules are summarized in Table 3-1.
TABLE 3-1:
POWER MANAGED MODES
OSCCON Bits
Mode
IDLEN(1) SCS1:SCS0
<7>
<1:0>
Sleep
ENTERING POWER MANAGED
MODES
Switching from one power managed mode to another
begins by loading the OSCCON register. The
SCS1:SCS0 bits select the clock source and determine
which Run or Idle mode is to be used. Changing these
bits causes an immediate switch to the new clock
source, assuming that it is running. The switch may
also be subject to clock transition delays. These are
discussed in Section 3.1.3 “Clock Transitions and
Status Indicators” and subsequent sections.
These categories define which portions of the device
are clocked and sometimes, what speed. The Run and
Idle modes may use any of the three available clock
sources (primary, secondary or internal oscillator
block); the Sleep mode does not use a clock source.
3.1
CLOCK SOURCES
Module Clocking
Available Clock and Oscillator Source
CPU
Peripherals
0
N/A
Off
Off
PRI_RUN
N/A
00
Clocked
Clocked
Primary – LP, XT, HS, HSPLL, RC, EC and
Internal Oscillator Block(2).
This is the normal full power execution mode.
SEC_RUN
N/A
01
Clocked
Clocked
Secondary – Timer1 Oscillator
RC_RUN
N/A
1x
Clocked
Clocked
Internal Oscillator Block(2)
PRI_IDLE
1
00
Off
Clocked
Primary – LP, XT, HS, HSPLL, RC, EC
SEC_IDLE
1
01
Off
Clocked
Secondary – Timer1 Oscillator
RC_IDLE
1
1x
Off
Clocked
Internal Oscillator Block(2)
Note 1:
2:
None – All clocks are disabled
IDLEN reflects its value when the SLEEP instruction is executed.
Includes INTOSC and INTOSC postscaler, as well as the INTRC source.
 2004 Microchip Technology Inc.
DS39636A-page 33
PIC18F2X1X/4X1X
3.1.3
CLOCK TRANSITIONS AND
STATUS INDICATORS
The length of the transition between clock sources is
the sum of two cycles of the old clock source and three
to four cycles of the new clock source. This formula
assumes that the new clock source is stable.
Three bits indicate the current clock source and its
status. They are:
• OSTS (OSCCON<3>)
• IOFS (OSCCON<2>)
• T1RUN (T1CON<6>)
In general, only one of these bits will be set while in a
given power managed mode. When the OSTS bit is
set, the primary clock is providing the device clock.
When the IOFS bit is set, the INTOSC output is
providing a stable 8 MHz clock source to a divider that
actually drives the device clock. When the T1RUN bit is
set, the Timer1 oscillator is providing the clock. If none
of these bits are set, then either the INTRC clock
source is clocking the device, or the INTOSC source is
not yet stable.
If the internal oscillator block is configured as the primary clock source by the FOSC3:FOSC0 configuration
bits, then both the OSTS and IOFS bits may be set
when in PRI_RUN or PRI_IDLE modes. This indicates
that the primary clock (INTOSC output) is generating a
stable 8 MHz output. Entering another RC Power
Managed mode at the same frequency would clear the
OSTS bit.
Note 1: Caution should be used when modifying a
single IRCF bit. If VDD is less than 3V, it is
possible to select a higher clock speed
than is supported by the low VDD.
Improper device operation may result if
the VDD/FOSC specifications are violated.
2: Executing a SLEEP instruction does not
necessarily place the device into Sleep
mode. It acts as the trigger to place the
controller into either the Sleep mode or
one of the Idle modes, depending on the
setting of the IDLEN bit.
3.1.4
MULTIPLE SLEEP COMMANDS
The power managed mode that is invoked with the
SLEEP instruction is determined by the setting of the
IDLEN bit at the time the instruction is executed. If
another SLEEP instruction is executed, the device will
enter the power managed mode specified by IDLEN at
that time. If IDLEN has changed, the device will enter
the new power managed mode specified by the new
setting.
DS39636A-page 34
3.2
Run Modes
In the Run modes, clocks to both the core and
peripherals are active. The difference between these
modes is the clock source.
3.2.1
PRI_RUN MODE
The PRI_RUN mode is the normal, full power execution
mode of the microcontroller. This is also the default
mode upon a device Reset, unless Two-Speed Start-up
is enabled (see Section 22.3 “Two-Speed Start-up”
for details). In this mode, the OSTS bit is set. The IOFS
bit may be set if the internal oscillator block is the
primary clock source (see Section 2.7.1 “Oscillator
Control Register”).
3.2.2
SEC_RUN MODE
The SEC_RUN mode is the compatible mode to the
“clock switching” feature offered in other PIC18
devices. In this mode, the CPU and peripherals are
clocked from the Timer1 oscillator. This gives users the
option of lower power consumption while still using a
high accuracy clock source.
SEC_RUN mode is entered by setting the SCS1:SCS0
bits to ‘01’. The device clock source is switched to the
Timer1 oscillator (see Figure 3-1), the primary oscillator is shut down, the T1RUN bit (T1CON<6>) is set and
the OSTS bit is cleared.
Note:
The Timer1 oscillator should already be
running prior to entering SEC_RUN mode.
If the T1OSCEN bit is not set when the
SCS1:SCS0 bits are set to ‘01’, entry to
SEC_RUN mode will not occur. If the
Timer1 oscillator is enabled but not yet
running, device clocks will be delayed until
the oscillator has started. In such situations, initial oscillator operation is far from
stable and unpredictable operation may
result.
On transitions from SEC_RUN mode to PRI_RUN, the
peripherals and CPU continue to be clocked from the
Timer1 oscillator while the primary clock is started.
When the primary clock becomes ready, a clock switch
back to the primary clock occurs (see Figure 3-2).
When the clock switch is complete, the T1RUN bit is
cleared, the OSTS bit is set and the primary clock is
providing the clock. The IDLEN and SCS bits are not
affected by the wake-up; the Timer1 oscillator
continues to run.
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
FIGURE 3-1:
TRANSITION TIMING FOR ENTRY TO SEC_RUN MODE
Q1 Q2 Q3 Q4 Q1
Q2
1
T1OSI
2
3
n-1
Q3
Q4
Q1
Q2
Q3
n
(1)
Clock Transition
OSC1
CPU
Clock
Peripheral
Clock
Program
Counter
Note 1:
PC
PC + 2
PC + 4
Clock transition typically occurs within 2-4 TOSC.
FIGURE 3-2:
TRANSITION TIMING FROM SEC_RUN MODE TO PRI_RUN MODE (HSPLL)
Q1
Q2
Q3
Q4
Q1
Q2 Q3 Q4 Q1 Q2 Q3
T1OSI
OSC1
TOST(1)
TPLL(1)
1
PLL Clock
Output
2
n-1 n
Clock (2)
Transition
CPU Clock
Peripheral
Clock
Program
Counter
SCS1:SCS0 bits changed
Note 1:
2:
3.2.3
PC + 2
PC
PC + 4
OSTS bit set
TOST = 1024 TOSC; TPLL = 2 ms (approx). These intervals are not shown to scale.
Clock transition typically occurs within 2-4 TOSC.
RC_RUN MODE
In RC_RUN mode, the CPU and peripherals are
clocked from the internal oscillator block using the
INTOSC multiplexer. In this mode, the primary clock is
shut down. When using the INTRC source, this mode
provides the best power conservation of all the Run
modes, while still executing code. It works well for user
applications which are not highly timing sensitive or do
not require high-speed clocks at all times.
If the primary clock source is the internal oscillator
block (either INTRC or INTOSC), there are no
distinguishable differences between PRI_RUN and
RC_RUN modes during execution. However, a clock
switch delay will occur during entry to and exit from
RC_RUN mode. Therefore, if the primary clock source
is the internal oscillator block, the use of RC_RUN
mode is not recommended.
 2004 Microchip Technology Inc.
This mode is entered by setting SCS1 to ‘1’. Although
it is ignored, it is recommended that SCS0 also be
cleared; this is to maintain software compatibility with
future devices. When the clock source is switched to
the INTOSC multiplexer (see Figure 3-3), the primary
oscillator is shut down and the OSTS bit is cleared. The
IRCF bits may be modified at any time to immediately
change the clock speed.
Note:
Caution should be used when modifying a
single IRCF bit. If VDD is less than 3V, it is
possible to select a higher clock speed
than is supported by the low VDD.
Improper device operation may result if
the VDD/FOSC specifications are violated.
DS39636A-page 35
PIC18F2X1X/4X1X
If the IRCF bits and the INTSRC bit are all clear, the
INTOSC output is not enabled and the IOFS bit will
remain clear; there will be no indication of the current
clock source. The INTRC source is providing the
device clocks.
On transitions from RC_RUN mode to PRI_RUN mode,
the device continues to be clocked from the INTOSC
multiplexer while the primary clock is started. When the
primary clock becomes ready, a clock switch to the
primary clock occurs (see Figure 3-4). When the clock
switch is complete, the IOFS bit is cleared, the OSTS
bit is set and the primary clock is providing the device
clock. The IDLEN and SCS bits are not affected by the
switch. The INTRC source will continue to run if either
the WDT or the Fail-Safe Clock Monitor is enabled.
If the IRCF bits are changed from all clear (thus,
enabling the INTOSC output) or if INTSRC is set, the
IOFS bit becomes set after the INTOSC output
becomes stable. Clocks to the device continue while
the INTOSC source stabilizes after an interval of
TIOBST.
If the IRCF bits were previously at a non-zero value, or
if INTSRC was set before setting SCS1 and the
INTOSC source was already stable, the IOFS bit will
remain set.
FIGURE 3-3:
TRANSITION TIMING TO RC_RUN MODE
Q1 Q2 Q3 Q4 Q1
Q2
1
INTRC
2
3
n-1
Q3
Q4
Q1
Q2
Q3
n
(1)
Clock Transition
OSC1
CPU
Clock
Peripheral
Clock
Program
Counter
Note 1:
PC
PC + 2
PC + 4
Clock transition typically occurs within 2-4 TOSC.
FIGURE 3-4:
TRANSITION TIMING FROM RC_RUN MODE TO PRI_RUN MODE
Q1
Q2
Q3
Q4
Q2 Q3 Q4 Q1 Q2 Q3
Q1
INTOSC
Multiplexer
OSC1
TOST(1)
TPLL(1)
1
PLL Clock
Output
2
n-1 n
(2)
Clock
Transition
CPU Clock
Peripheral
Clock
Program
Counter
SCS1:SCS0 bits changed
Note 1:
2:
DS39636A-page 36
PC + 2
PC
PC + 4
OSTS bit set
TOST = 1024 TOSC; TPLL = 2 ms (approx). These intervals are not shown to scale.
Clock transition typically occurs within 2-4 TOSC.
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
3.3
Sleep Mode
3.4
The Power Managed Sleep mode in the PIC18F2X1X/
4X1X devices is identical to the legacy Sleep mode
offered in all other PICmicro devices. It is entered by
clearing the IDLEN bit (the default state on device
Reset) and executing the SLEEP instruction. This shuts
down the selected oscillator (Figure 3-5). All clock
source status bits are cleared.
Idle Modes
The Idle modes allow the controller’s CPU to be
selectively shut down while the peripherals continue to
operate. Selecting a particular Idle mode allows users
to further manage power consumption.
If the IDLEN bit is set to a ‘1’ when a SLEEP instruction is
executed, the peripherals will be clocked from the clock
source selected using the SCS1:SCS0 bits; however, the
CPU will not be clocked. The clock source status bits are
not affected. Setting IDLEN and executing a SLEEP
instruction provides a quick method of switching from a
given Run mode to its corresponding Idle mode.
Entering the Sleep mode from any other mode does not
require a clock switch. This is because no clocks are
needed once the controller has entered Sleep. If the
WDT is selected, the INTRC source will continue to
operate. If the Timer1 oscillator is enabled, it will also
continue to run.
If the WDT is selected, the INTRC source will continue
to operate. If the Timer1 oscillator is enabled, it will also
continue to run.
When a wake event occurs in Sleep mode (by interrupt,
Reset or WDT time-out), the device will not be clocked
until the clock source selected by the SCS1:SCS0 bits
becomes ready (see Figure 3-6), or it will be clocked
from the internal oscillator block if either the TwoSpeed Start-up or the Fail-Safe Clock Monitor are
enabled (see Section 22.0 “Special Features of the
CPU”). In either case, the OSTS bit is set when the primary clock is providing the device clocks. The IDLEN
and SCS bits are not affected by the wake-up.
Since the CPU is not executing instructions, the only
exits from any of the Idle modes are by interrupt, WDT
time-out or a Reset. When a wake event occurs, CPU
execution is delayed by an interval of TCSD
(parameter 38, Table 25-10) while it becomes ready to
execute code. When the CPU begins executing code,
it resumes with the same clock source for the current
Idle mode. For example, when waking from RC_IDLE
mode, the internal oscillator block will clock the CPU
and peripherals (in other words, RC_RUN mode). The
IDLEN and SCS bits are not affected by the wake-up.
While in any Idle mode or the Sleep mode, a WDT timeout will result in a WDT wake-up to the Run mode
currently specified by the SCS1:SCS0 bits.
FIGURE 3-5:
TRANSITION TIMING FOR ENTRY TO SLEEP MODE
Q1 Q2 Q3 Q4 Q1
OSC1
CPU
Clock
Peripheral
Clock
Sleep
Program
Counter
PC
FIGURE 3-6:
PC + 2
TRANSITION TIMING FOR WAKE FROM SLEEP (HSPLL)
Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
Q1
OSC1
TOST(1)
PLL Clock
Output
TPLL(1)
CPU Clock
Peripheral
Clock
Program
Counter
PC
Wake Event
PC + 2
PC + 4
PC + 6
OSTS bit set
Note1: TOST = 1024 TOSC; TPLL = 2 ms (approx). These intervals are not shown to scale.
 2004 Microchip Technology Inc.
DS39636A-page 37
PIC18F2X1X/4X1X
3.4.1
PRI_IDLE MODE
3.4.2
This mode is unique among the three low-power Idle
modes, in that it does not disable the primary device
clock. For timing sensitive applications, this allows for
the fastest resumption of device operation with its more
accurate primary clock source, since the clock source
does not have to “warm up” or transition from another
oscillator.
PRI_IDLE mode is entered from PRI_RUN mode by
setting the IDLEN bit and executing a SLEEP instruction. If the device is in another Run mode, set IDLEN
first, then clear the SCS bits and execute SLEEP.
Although the CPU is disabled, the peripherals continue
to be clocked from the primary clock source specified
by the FOSC3:FOSC0 configuration bits. The OSTS bit
remains set (see Figure 3-7).
In SEC_IDLE mode, the CPU is disabled but the
peripherals continue to be clocked from the Timer1
oscillator. This mode is entered from SEC_RUN by
setting the IDLEN bit and executing a SLEEP
instruction. If the device is in another Run mode, set
IDLEN first, then set SCS1:SCS0 to ‘01’ and execute
SLEEP. When the clock source is switched to the
Timer1 oscillator, the primary oscillator is shut down,
the OSTS bit is cleared and the T1RUN bit is set.
When a wake event occurs, the peripherals continue to
be clocked from the Timer1 oscillator. After an interval
of TCSD following the wake event, the CPU begins executing code being clocked by the Timer1 oscillator. The
IDLEN and SCS bits are not affected by the wake-up;
the Timer1 oscillator continues to run (see Figure 3-8).
When a wake event occurs, the CPU is clocked from the
primary clock source. A delay of interval TCSD is
required between the wake event and when code
execution starts. This is required to allow the CPU to
become ready to execute instructions. After the wakeup, the OSTS bit remains set. The IDLEN and SCS bits
are not affected by the wake-up (see Figure 3-8).
FIGURE 3-7:
SEC_IDLE MODE
Note:
The Timer1 oscillator should already be
running prior to entering SEC_IDLE mode.
If the T1OSCEN bit is not set when the
SLEEP instruction is executed, the SLEEP
instruction will be ignored and entry to
SEC_IDLE mode will not occur. If the
Timer1 oscillator is enabled but not yet
running, peripheral clocks will be delayed
until the oscillator has started. In such
situations, initial oscillator operation is far
from stable and unpredictable operation
may result.
TRANSITION TIMING FOR ENTRY TO IDLE MODE
Q1
Q3
Q2
Q4
Q1
OSC1
CPU Clock
Peripheral
Clock
Program
Counter
PC
FIGURE 3-8:
PC + 2
TRANSITION TIMING FOR WAKE FROM IDLE TO RUN MODE
Q1
Q2
Q3
Q4
OSC1
TCSD
CPU Clock
Peripheral
Clock
Program
Counter
PC
Wake Event
DS39636A-page 38
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
3.4.3
RC_IDLE MODE
In RC_IDLE mode, the CPU is disabled but the peripherals continue to be clocked from the internal oscillator
block using the INTOSC multiplexer. This mode allows
for controllable power conservation during Idle periods.
From RC_RUN, this mode is entered by setting the
IDLEN bit and executing a SLEEP instruction. If the
device is in another Run mode, first set IDLEN, then set
the SCS1 bit and execute SLEEP. Although its value is
ignored, it is recommended that SCS0 also be cleared;
this is to maintain software compatibility with future
devices. The INTOSC multiplexer may be used to
select a higher clock frequency by modifying the IRCF
bits before executing the SLEEP instruction. When the
clock source is switched to the INTOSC multiplexer, the
primary oscillator is shut down and the OSTS bit is
cleared.
If the IRCF bits are set to any non-zero value, or the
INTSRC bit is set, the INTOSC output is enabled. The
IOFS bit becomes set, after the INTOSC output
becomes stable, after an interval of TIOBST
(parameter 39, Table 25-10). Clocks to the peripherals
continue while the INTOSC source stabilizes. If the
IRCF bits were previously at a non-zero value, or
INTSRC was set before the SLEEP instruction was executed and the INTOSC source was already stable, the
IOFS bit will remain set. If the IRCF bits and INTSRC
are all clear, the INTOSC output will not be enabled, the
IOFS bit will remain clear and there will be no indication
of the current clock source.
When a wake event occurs, the peripherals continue to
be clocked from the INTOSC multiplexer. After a delay
of TCSD following the wake event, the CPU begins
executing code being clocked by the INTOSC multiplexer. The IDLEN and SCS bits are not affected by the
wake-up. The INTRC source will continue to run if
either the WDT or the Fail-Safe Clock Monitor is
enabled.
3.5
Exiting Idle and Sleep Modes
An exit from Sleep mode or any of the Idle modes is
triggered by an interrupt, a Reset or a WDT time-out.
This section discusses the triggers that cause exits
from power managed modes. The clocking subsystem
actions are discussed in each of the power managed
modes (see Section 3.2 “Run Modes”, Section 3.3
“Sleep Mode” and Section 3.4 “Idle Modes”).
3.5.1
EXIT BY INTERRUPT
Any of the available interrupt sources can cause the
device to exit from an Idle mode or the Sleep mode to
a Run mode. To enable this functionality, an interrupt
source must be enabled by setting its enable bit in one
of the INTCON or PIE registers. The exit sequence is
initiated when the corresponding interrupt flag bit is set.
 2004 Microchip Technology Inc.
On all exits from Idle or Sleep modes by interrupt, code
execution branches to the interrupt vector if the GIE/
GIEH bit (INTCON<7>) is set. Otherwise, code execution continues or resumes without branching (see
Section 8.0 “Interrupts”).
A fixed delay of interval TCSD following the wake event
is required when leaving Sleep and Idle modes. This
delay is required for the CPU to prepare for execution.
Instruction execution resumes on the first clock cycle
following this delay.
3.5.2
EXIT BY WDT TIME-OUT
A WDT time-out will cause different actions depending
on which power managed mode the device is in when
the time-out occurs.
If the device is not executing code (all Idle modes and
Sleep mode), the time-out will result in an exit from the
power managed mode (see Section 3.2 “Run Modes”
and Section 3.3 “Sleep Mode”). If the device is
executing code (all Run modes), the time-out will result
in a WDT Reset (see Section 22.2 “Watchdog Timer
(WDT)”).
The WDT timer and postscaler are cleared by
executing a SLEEP or CLRWDT instruction, the loss of a
currently selected clock source (if the Fail-Safe Clock
Monitor is enabled) and modifying the IRCF bits in the
OSCCON register if the internal oscillator block is the
device clock source.
3.5.3
EXIT BY RESET
Normally, the device is held in Reset by the Oscillator
Start-up Timer (OST) until the primary clock becomes
ready. At that time, the OSTS bit is set and the device
begins executing code. If the internal oscillator block is
the new clock source, the IOFS bit is set instead.
The exit delay time from Reset to the start of code
execution depends on both the clock sources before
and after the wake-up and the type of oscillator if the
new clock source is the primary clock. Exit delays are
summarized in Table 3-2.
Code execution can begin before the primary clock
becomes ready. If either the Two-Speed Start-up (see
Section 22.3 “Two-Speed Start-up”) or Fail-Safe
Clock Monitor (see Section 22.4 “Fail-Safe Clock
Monitor”) is enabled, the device may begin execution
as soon as the Reset source has cleared. Execution is
clocked by the INTOSC multiplexer driven by the
internal oscillator block. Execution is clocked by the
internal oscillator block until either the primary clock
becomes ready or a power managed mode is entered
before the primary clock becomes ready; the primary
clock is then shut down.
DS39636A-page 39
PIC18F2X1X/4X1X
3.5.4
EXIT WITHOUT AN OSCILLATOR
START-UP DELAY
Certain exits from power managed modes do not
invoke the OST at all. There are two cases:
• PRI_IDLE mode, where the primary clock source
is not stopped; and
• the primary clock source is not any of the LP, XT,
HS or HSPLL modes.
TABLE 3-2:
In these instances, the primary clock source either
does not require an oscillator start-up delay since it is
already running (PRI_IDLE), or normally does not
require an oscillator start-up delay (RC, EC and INTIO
Oscillator modes). However, a fixed delay of interval
TCSD following the wake event is still required when
leaving Sleep and Idle modes to allow the CPU to
prepare for execution. Instruction execution resumes
on the first clock cycle following this delay.
EXIT DELAY ON WAKE-UP BY RESET FROM SLEEP MODE OR ANY IDLE MODE
(BY CLOCK SOURCES)
Clock Source
before Wake-up
Clock Source
after Wake-up
Exit Delay
Clock Ready Status
bit (OSCCON)
LP, XT, HS
Primary Device Clock
(PRI_IDLE mode)
OSTS
HSPLL
EC, RC
TCSD(2)
INTRC(1)
—
INTOSC(3)
T1OSC or INTRC(1)
INTOSC(3)
None
(Sleep mode)
LP, XT, HS
HSPLL
TOST + trc(4)
OSTS
EC, RC
INTOSC(2)
TCSD(2)
TIOBST(5)
IOFS
LP, XT, HS
TOST(5)
HSPLL
TOST + trc(4)
3:
4:
5:
OSTS
EC, RC
TCSD(2)
INTOSC(2)
None
LP, XT, HS
TOST(4)
HSPLL
TOST + trc(4)
OSTS
EC, RC
TCSD(2)
TIOBST(5)
IOFS
INTOSC(2)
Note 1:
2:
IOFS
TOST(4)
IOFS
In this instance, refers specifically to the 31 kHz INTRC clock source.
TCSD (parameter 38) is a required delay when waking from Sleep and all Idle modes and runs concurrently
with any other required delays (see Section 3.4 “Idle Modes”). On Reset, INTOSC defaults to 1 MHz.
Includes both the INTOSC 8 MHz source and postscaler derived frequencies.
TOST is the Oscillator Start-up Timer (parameter 32). trc is the PLL Lock-out Timer (parameter F12); it is
also designated as TPLL.
Execution continues during TIOBST (parameter 39), the INTOSC stabilization period.
DS39636A-page 40
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
4.0
RESET
A simplified block diagram of the On-Chip Reset Circuit
is shown in Figure 4-1.
The PIC18F2X1X/4X1X devices differentiate between
various kinds of Reset:
a)
b)
c)
d)
e)
f)
g)
h)
Power-on Reset (POR)
MCLR Reset during normal operation
MCLR Reset during power managed modes
Watchdog Timer (WDT) Reset (during
execution)
Programmable Brown-out Reset (BOR)
RESET Instruction
Stack Full Reset
Stack Underflow Reset
RCON Register
Device Reset events are tracked through the RCON
register (Register 4-1). The lower five bits of the
register indicate that a specific Reset event has
occurred. In most cases, these bits can only be cleared
by the event and must be set by the application after
the event. The state of these flag bits, taken together,
can be read to indicate the type of Reset that just
occurred. This is described in more detail in
Section 4.6 “Reset State of Registers”.
This section discusses Resets generated by MCLR,
POR and BOR and covers the operation of the various
start-up timers. Stack Reset events are covered in
Section 5.1.2.4 “Stack Full and Underflow Resets”.
WDT Resets are covered in Section 22.2 “Watchdog
Timer (WDT)”.
FIGURE 4-1:
4.1
The RCON register also has control bits for setting
interrupt priority (IPEN) and software control of the
BOR (SBOREN). Interrupt priority is discussed in
Section 8.0 “Interrupts”. BOR is covered in
Section 4.4 “Brown-out Reset (BOR)”.
SIMPLIFIED BLOCK DIAGRAM OF ON-CHIP RESET CIRCUIT
RESET
Instruction
Stack Full/Underflow Reset
Stack
Pointer
External Reset
MCLR
MCLRE
( )_IDLE
Sleep
WDT
Time-out
VDD Rise
Detect
POR Pulse
VDD
Brown-out
Reset
S
BOREN
OST/PWRT
OST
1024 Cycles
Chip_Reset
10-bit Ripple Counter
R
Q
OSC1
32 µs
INTRC(1)
PWRT
65.5 ms
11-bit Ripple Counter
Enable PWRT
Enable OST(2)
Note 1:
2:
This is the INTRC source from the internal oscillator block and is separate from the RC oscillator of the CLKI pin.
See Table 4-2 for time-out situations.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 41
PIC18F2X1X/4X1X
REGISTER 4-1:
RCON: RESET CONTROL REGISTER
R/W-0
R/W-1(1)
U-0
R/W-1
R-1
R-1
R/W-0(2)
R/W-0
IPEN
SBOREN
—
RI
TO
PD
POR
BOR
bit 7
bit 0
bit 7
IPEN: Interrupt Priority Enable bit
1 = Enable priority levels on interrupts
0 = Disable priority levels on interrupts (PIC16CXXX Compatibility mode)
bit 6
SBOREN: BOR Software Enable bit(1)
If BOREN1:BOREN0 = 01:
1 = BOR is enabled
0 = BOR is disabled
If BOREN1:BOREN0 = 00, 10 or 11:
Bit is disabled and read as ‘0’.
bit 5
Unimplemented: Read as ‘0’
bit 4
RI: RESET Instruction Flag bit
1 = The RESET instruction was not executed (set by firmware only)
0 = The RESET instruction was executed causing a device Reset (must be set in software after
a Brown-out Reset occurs)
bit 3
TO: Watchdog Time-out Flag bit
1 = Set by power-up, CLRWDT instruction or SLEEP instruction
0 = A WDT time-out occurred
bit 2
PD: Power-down Detection Flag bit
1 = Set by power-up or by the CLRWDT instruction
0 = Set by execution of the SLEEP instruction
bit 1
POR: Power-on Reset Status bit(2)
1 = A Power-on Reset has not occurred (set by firmware only)
0 = A Power-on Reset occurred (must be set in software after a Power-on Reset occurs)
bit 0
BOR: Brown-out Reset Status bit
1 = A Brown-out Reset has not occurred (set by firmware only)
0 = A Brown-out Reset occurred (must be set in software after a Brown-out Reset occurs)
Note 1: The SBOREN bit is only available when the BOREN1:BOREN0 configuration
bits = 01; otherwise, it is disabled and reads as ‘0’. See Section 4.4 “Brown-out
Reset (BOR)”.
2: The actual Reset value of POR is determined by the type of device Reset. See the
notes following this register and Section 4.6 “Reset State of Registers” for
additional information.
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
Note 1: It is recommended that the POR bit be set after a Power-on Reset has been
detected so that subsequent Power-on Resets may be detected.
2: Brown-out Reset is said to have occurred when BOR is ‘0’ and POR is ‘1’ (assuming
that POR was set to ‘1’ by software immediately after POR).
DS39636A-page 42
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
4.2
FIGURE 4-2:
Master Clear (MCLR)
The MCLR pin provides a method for triggering an
external Reset of the device. A Reset is generated by
holding the pin low. These devices have a noise filter in
the MCLR Reset path which detects and ignores small
pulses.
In PIC18F2X1X/4X1X devices, the MCLR input can be
disabled with the MCLRE configuration bit. When
MCLR is disabled, the pin becomes a digital input. See
Section 9.5 “PORTE, TRISE and LATE Registers”
for more information.
4.3
VDD
VDD
The MCLR pin is not driven low by any internal Resets,
including the WDT.
EXTERNAL POWER-ON
RESET CIRCUIT (FOR
SLOW VDD POWER-UP)
D
R
R1
MCLR
C
PIC18FXXXX
Note 1:
External Power-on Reset circuit is required
only if the VDD power-up slope is too slow.
The diode D helps discharge the capacitor
quickly when VDD powers down.
2:
R < 40 kΩ is recommended to make sure that
the voltage drop across R does not violate
the device’s electrical specification.
3:
R1 ≥ 1 kΩ will limit any current flowing into
MCLR from external capacitor C, in the event
of MCLR/VPP pin breakdown, due to
Electrostatic Discharge (ESD) or Electrical
Overstress (EOS).
Power-on Reset (POR)
A Power-on Reset pulse is generated on-chip
whenever VDD rises above a certain threshold. This
allows the device to start in the initialized state when
VDD is adequate for operation.
To take advantage of the POR circuitry, tie the MCLR
pin through a resistor (1 kΩ to 10 kΩ) to VDD. This will
eliminate external RC components usually needed to
create a Power-on Reset delay. A minimum rise rate for
VDD is specified (parameter D004). For a slow rise
time, see Figure 4-2.
When the device starts normal operation (i.e., exits the
Reset condition), device operating parameters (voltage, frequency, temperature, etc.) must be met to
ensure operation. If these conditions are not met, the
device must be held in Reset until the operating
conditions are met.
POR events are captured by the POR bit (RCON<1>).
The state of the bit is set to ‘0’ whenever a POR occurs;
it does not change for any other Reset event. POR is
not reset to ‘1’ by any hardware event. To capture
multiple events, the user manually resets the bit to ‘1’
in software following any POR.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 43
PIC18F2X1X/4X1X
4.4
Brown-out Reset (BOR)
PIC18F2X1X/4X1X devices implement a BOR circuit
that provides the user with a number of configuration
and power-saving options. The BOR is controlled by
the BORV1:BORV0 and BOREN1:BOREN0 configuration bits. There are a total of four BOR configurations
which are summarized in Table 4-1.
The BOR threshold is set by the BORV1:BORV0 bits. If
BOR is enabled (any values of BOREN1:BOREN0,
except ‘00’), any drop of VDD below VBOR (parameter
D005) for greater than TBOR (parameter 35) will reset
the device. A Reset may or may not occur if VDD falls
below VBOR for less than TBOR. The chip will remain in
Brown-out Reset until VDD rises above VBOR.
Placing the BOR under software control gives the user
the additional flexibility of tailoring the application to its
environment without having to reprogram the device to
change BOR configuration. It also allows the user to
tailor device power consumption in software by eliminating the incremental current that the BOR consumes.
While the BOR current is typically very small, it may
have some impact in low-power applications.
Note:
4.4.2
Even when BOR is under software control,
the BOR Reset voltage level is still set by
the BORV1:BORV0 configuration bits. It
cannot be changed in software.
DETECTING BOR
If the Power-up Timer is enabled, it will be invoked after
VDD rises above VBOR; it then will keep the chip in
Reset for an additional time delay, TPWRT
(parameter 33). If VDD drops below VBOR while the
Power-up Timer is running, the chip will go back into a
Brown-out Reset and the Power-up Timer will be
initialized. Once VDD rises above VBOR, the Power-up
Timer will execute the additional time delay.
When BOR is enabled, the BOR bit always resets to ‘0’
on any BOR or POR event. This makes it difficult to
determine if a BOR event has occurred just by reading
the state of BOR alone. A more reliable method is to
simultaneously check the state of both POR and BOR.
This assumes that the POR bit is reset to ‘1’ in software
immediately after any POR event. If BOR is ‘0’ while
POR is ‘1’, it can be reliably assumed that a BOR event
has occurred.
BOR and the Power-on Timer (PWRT) are
independently configured. Enabling BOR Reset does
not automatically enable the PWRT.
4.4.3
4.4.1
SOFTWARE ENABLED BOR
When BOREN1:BOREN0 = 01, the BOR can be
enabled or disabled by the user in software. This is
done with the control bit, SBOREN (RCON<6>).
Setting SBOREN enables the BOR to function as
previously described. Clearing SBOREN disables the
BOR entirely. The SBOREN bit operates only in this
mode; otherwise it is read as ‘0’.
TABLE 4-1:
DISABLING BOR IN SLEEP MODE
When BOREN1:BOREN0 = 10, the BOR remains
under hardware control and operates as previously
described. Whenever the device enters Sleep mode,
however, the BOR is automatically disabled. When the
device returns to any other operating mode, BOR is
automatically re-enabled.
This mode allows for applications to recover from
brown-out situations, while actively executing code,
when the device requires BOR protection the most. At
the same time, it saves additional power in Sleep mode
by eliminating the small incremental BOR current.
BOR CONFIGURATIONS
BOR Configuration
BOREN1
BOREN0
Status of
SBOREN
(RCON<6>)
0
0
Unavailable
0
1
Available
1
0
Unavailable
BOR enabled in hardware in Run and Idle modes, disabled during
Sleep mode.
1
1
Unavailable
BOR enabled in hardware; must be disabled by reprogramming the
configuration bits.
DS39636A-page 44
BOR Operation
BOR disabled; must be enabled by reprogramming the configuration bits.
BOR enabled in software; operation controlled by SBOREN.
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
4.5
4.5.3
Device Reset Timers
PIC18F2X1X/4X1X devices incorporate three separate
on-chip timers that help regulate the Power-on Reset
process. Their main function is to ensure that the
device clock is stable before code is executed. These
timers are:
• Power-up Timer (PWRT)
• Oscillator Start-up Timer (OST)
• PLL Lock Time-out
4.5.1
With the PLL enabled in its PLL mode, the time-out
sequence following a Power-on Reset is slightly different from other oscillator modes. A separate timer is
used to provide a fixed time-out that is sufficient for the
PLL to lock to the main oscillator frequency. This PLL
lock time-out (TPLL) is typically 2 ms and follows the
oscillator start-up time-out.
4.5.4
TIME-OUT SEQUENCE
On power-up, the time-out sequence is as follows:
POWER-UP TIMER (PWRT)
The Power-up Timer (PWRT) of PIC18F2X1X/4X1X
devices is an 11-bit counter which uses the INTRC
source as the clock input. This yields an approximate
time interval of 2048 x 32 µs = 65.6 ms. While the
PWRT is counting, the device is held in Reset.
The power-up time delay depends on the INTRC clock
and will vary from chip to chip due to temperature and
process variation. See DC parameter 33 for details.
The PWRT is enabled by clearing the PWRTEN
configuration bit.
4.5.2
PLL LOCK TIME-OUT
OSCILLATOR START-UP TIMER
(OST)
The Oscillator Start-up Timer (OST) provides a 1024
oscillator cycle (from OSC1 input) delay after the
PWRT delay is over (parameter 33). This ensures that
the crystal oscillator or resonator has started and
stabilized.
1.
2.
After the POR pulse has cleared, PWRT time-out
is invoked (if enabled).
Then, the OST is activated.
The total time-out will vary based on oscillator configuration and the status of the PWRT. Figure 4-3,
Figure 4-4, Figure 4-5, Figure 4-6 and Figure 4-7 all
depict time-out sequences on power-up, with the
Power-up Timer enabled and the device operating in
HS Oscillator mode. Figures 4-3 through 4-6 also
apply to devices operating in XT or LP modes. For
devices in RC mode and with the PWRT disabled, there
will be no time-out at all.
Since the time-outs occur from the POR pulse, if MCLR
is kept low long enough, all time-outs will expire. Bringing MCLR high will begin execution immediately
(Figure 4-5). This is useful for testing purposes or to
synchronize more than one PIC18FXXXX device
operating in parallel.
The OST time-out is invoked only for XT, LP, HS and
HSPLL modes and only on Power-on Reset, or on exit
from most power managed modes.
TABLE 4-2:
TIME-OUT IN VARIOUS SITUATIONS
Power-up(2) and Brown-out
Oscillator
Configuration
HSPLL
PWRTEN = 0
PWRTEN = 1
Exit from
Power Managed Mode
66 ms(1) + 1024 TOSC + 2 ms(2)
1024 TOSC + 2 ms(2)
1024 TOSC + 2 ms(2)
HS, XT, LP
1024 TOSC
1024 TOSC
EC, ECIO
66
ms(1)
—
—
RC, RCIO
66 ms(1)
—
—
ms(1)
—
—
INTIO1, INTIO2
66
ms(1)
+ 1024 TOSC
66
Note 1: 66 ms (65.5 ms) is the nominal Power-up Timer (PWRT) delay.
2: 2 ms is the nominal time required for the PLL to lock.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 45
PIC18F2X1X/4X1X
FIGURE 4-3:
TIME-OUT SEQUENCE ON POWER-UP (MCLR TIED TO VDD, VDD RISE < TPWRT)
VDD
MCLR
INTERNAL POR
TPWRT
PWRT TIME-OUT
TOST
OST TIME-OUT
INTERNAL RESET
TIME-OUT SEQUENCE ON POWER-UP (MCLR NOT TIED TO VDD): CASE 1
FIGURE 4-4:
VDD
MCLR
INTERNAL POR
TPWRT
PWRT TIME-OUT
TOST
OST TIME-OUT
INTERNAL RESET
TIME-OUT SEQUENCE ON POWER-UP (MCLR NOT TIED TO VDD): CASE 2
FIGURE 4-5:
VDD
MCLR
INTERNAL POR
TPWRT
PWRT TIME-OUT
TOST
OST TIME-OUT
INTERNAL RESET
DS39636A-page 46
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
FIGURE 4-6:
SLOW RISE TIME (MCLR TIED TO VDD, VDD RISE > TPWRT)
5V
VDD
0V
MCLR
INTERNAL POR
TPWRT
PWRT TIME-OUT
TOST
OST TIME-OUT
INTERNAL RESET
TIME-OUT SEQUENCE ON POR W/PLL ENABLED (MCLR TIED TO VDD)
FIGURE 4-7:
VDD
MCLR
INTERNAL POR
TPWRT
PWRT TIME-OUT
TOST
TPLL
OST TIME-OUT
PLL TIME-OUT
INTERNAL RESET
Note:
TOST = 1024 clock cycles.
TPLL ≈ 2 ms max. First three stages of the PWRT timer.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 47
PIC18F2X1X/4X1X
4.6
Reset State of Registers
Most registers are unaffected by a Reset. Their status
is unknown on POR and unchanged by all other
Resets. The other registers are forced to a “Reset
state” depending on the type of Reset that occurred.
Table 4-4 describes the Reset states for all of the
Special Function Registers. These are categorized by
Power-on and Brown-out Resets, Master Clear and
WDT Resets and WDT wake-ups.
Most registers are not affected by a WDT wake-up,
since this is viewed as the resumption of normal operation. Status bits from the RCON register, RI, TO, PD,
POR and BOR, are set or cleared differently in different
Reset situations, as indicated in Table 4-3. These bits
are used in software to determine the nature of the
Reset.
TABLE 4-3:
STATUS BITS, THEIR SIGNIFICANCE AND THE INITIALIZATION CONDITION
FOR RCON REGISTER
RCON Register
STKPTR Register
Program
Counter
SBOREN
RI
TO
PD
0000h
1
1
1
1
0
0
0
0
RESET Instruction
0000h
u(2)
0
u
u
u
u
u
u
Brown-out Reset
0000h
u(2)
1
1
1
u
0
u
u
MCLR during Power Managed
Run Modes
0000h
u(2)
u
1
u
u
u
u
u
MCLR during Power Managed
Idle Modes and Sleep Mode
0000h
u(2)
u
1
0
u
u
u
u
WDT Time-out during Full Power
or Power Managed Run Mode
0000h
u(2)
u
0
u
u
u
u
u
MCLR during Full Power
Execution
0000h
u(2)
u
u
u
u
u
u
u
Stack Full Reset (STVREN = 1)
0000h
u(2)
u
u
u
u
u
1
u
Stack Underflow Reset
(STVREN = 1)
0000h
(2)
u
u
u
u
u
u
u
1
Stack Underflow Error (not an
actual Reset, STVREN = 0)
0000h
u(2)
u
u
u
u
u
u
1
WDT Time-out during Power
Managed Idle or Sleep Modes
PC + 2
u(2)
u
0
0
u
u
u
u
PC + 2(1)
u(2)
u
u
0
u
u
u
u
Condition
Power-on Reset
Interrupt Exit from Power
Managed Modes
POR BOR STKFUL
STKUNF
Legend: u = unchanged
Note 1: When the wake-up is due to an interrupt and the GIEH or GIEL bits are set, the PC is loaded with the
interrupt vector (008h or 0018h).
2: Reset state is ‘1’ for POR and unchanged for all other Resets when software BOR is enabled
(BOREN1:BOREN0 configuration bits = 01 and SBOREN = 1). Otherwise, the Reset state is ‘0’.
DS39636A-page 48
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
TABLE 4-4:
INITIALIZATION CONDITIONS FOR ALL REGISTERS
Register
Applicable Devices
Power-on Reset,
Brown-out
Reset
MCLR Resets,
WDT Reset,
RESET
Instruction,
Stack Resets
Wake-up via
WDT
or Interrupt
TOSU
2410
2510
2515
2610
4410
4510
4515
4610
---0 0000
---0 0000
---0 uuuu(3)
TOSH
2410
2510
2515
2610
4410
4510
4515
4610
0000 0000
0000 0000
uuuu uuuu(3)
TOSL
2410
2510
2515
2610
4410
4510
4515
4610
0000 0000
0000 0000
uuuu uuuu(3)
STKPTR
2410
2510
2515
2610
4410
4510
4515
4610
00-0 0000
uu-0 0000
uu-u uuuu(3)
PCLATU
2410
2510
2515
2610
4410
4510
4515
4610
---0 0000
---0 0000
---u uuuu
PCLATH
2410
2510
2515
2610
4410
4510
4515
4610
0000 0000
0000 0000
uuuu uuuu
PCL
2410
2510
2515
2610
4410
4510
4515
4610
0000 0000
0000 0000
PC + 2(2)
TBLPTRU
2410
2510
2515
2610
4410
4510
4515
4610
--00 0000
--00 0000
--uu uuuu
TBLPTRH
2410
2510
2515
2610
4410
4510
4515
4610
0000 0000
0000 0000
uuuu uuuu
TBLPTRL
2410
2510
2515
2610
4410
4510
4515
4610
0000 0000
0000 0000
uuuu uuuu
TABLAT
2410
2510
2515
2610
4410
4510
4515
4610
0000 0000
0000 0000
uuuu uuuu
PRODH
2410
2510
2515
2610
4410
4510
4515
4610
xxxx xxxx
uuuu uuuu
uuuu uuuu
PRODL
2410
2510
2515
2610
4410
4510
4515
4610
xxxx xxxx
uuuu uuuu
uuuu uuuu
INTCON
2410
2510
2515
2610
4410
4510
4515
4610
0000 000x
0000 000u
uuuu uuuu(1)
INTCON2
2410
2510
2515
2610
4410
4510
4515
4610
1111 -1-1
1111 -1-1
uuuu -u-u(1)
INTCON3
2410
2510
2515
2610
4410
4510
4515
4610
11-0 0-00
11-0 0-00
uu-u u-uu(1)
INDF0
2410
2510
2515
2610
4410
4510
4515
4610
N/A
N/A
N/A
POSTINC0
2410
2510
2515
2610
4410
4510
4515
4610
N/A
N/A
N/A
POSTDEC0
2410
2510
2515
2610
4410
4510
4515
4610
N/A
N/A
N/A
PREINC0
2410
2510
2515
2610
4410
4510
4515
4610
N/A
N/A
N/A
PLUSW0
2410
2510
2515
2610
4410
4510
4515
4610
N/A
N/A
N/A
FSR0H
2410
2510
2515
2610
4410
4510
4515
4610
---- 0000
---- 0000
---- uuuu
FSR0L
2410
2510
2515
2610
4410
4510
4515
4610
xxxx xxxx
uuuu uuuu
uuuu uuuu
WREG
2410
2510
2515
2610
4410
4510
4515
4610
xxxx xxxx
uuuu uuuu
uuuu uuuu
INDF1
2410
2510
2515
2610
4410
4510
4515
4610
N/A
N/A
N/A
POSTINC1
2410
2510
2515
2610
4410
4510
4515
4610
N/A
N/A
N/A
POSTDEC1
2410
2510
2515
2610
4410
4510
4515
4610
N/A
N/A
N/A
PREINC1
2410
2510
2515
2610
4410
4510
4515
4610
N/A
N/A
N/A
PLUSW1
2410
2510
2515
2610
4410
4510
4515
4610
N/A
N/A
N/A
Legend:
Note 1:
2:
3:
4:
5:
u = unchanged, x = unknown, - = unimplemented bit, read as ‘0’, q = value depends on condition.
Shaded cells indicate conditions do not apply for the designated device.
One or more bits in the INTCONx or PIRx registers will be affected (to cause wake-up).
When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the PC is loaded with the interrupt vector
(0008h or 0018h).
When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the TOSU, TOSH and TOSL are updated with
the current value of the PC. The STKPTR is modified to point to the next location in the hardware stack.
See Table 4-3 for Reset value for specific condition.
Bits 6 and 7 of PORTA, LATA and TRISA are enabled, depending on the oscillator mode selected. When not enabled as
PORTA pins, they are disabled and read ‘0’.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 49
PIC18F2X1X/4X1X
TABLE 4-4:
INITIALIZATION CONDITIONS FOR ALL REGISTERS (CONTINUED)
Register
Applicable Devices
Power-on Reset,
Brown-out
Reset
MCLR Resets,
WDT Reset,
RESET
Instruction,
Stack Resets
Wake-up via
WDT
or Interrupt
FSR1H
2410
2510
2515
2610
4410
4510
4515
4610
---- 0000
---- 0000
---- uuuu
FSR1L
2410
2510
2515
2610
4410
4510
4515
4610
xxxx xxxx
uuuu uuuu
uuuu uuuu
BSR
2410
2510
2515
2610
4410
4510
4515
4610
---- 0000
---- 0000
---- uuuu
INDF2
2410
2510
2515
2610
4410
4510
4515
4610
N/A
N/A
N/A
POSTINC2
2410
2510
2515
2610
4410
4510
4515
4610
N/A
N/A
N/A
POSTDEC2
2410
2510
2515
2610
4410
4510
4515
4610
N/A
N/A
N/A
PREINC2
2410
2510
2515
2610
4410
4510
4515
4610
N/A
N/A
N/A
PLUSW2
2410
2510
2515
2610
4410
4510
4515
4610
N/A
N/A
N/A
FSR2H
2410
2510
2515
2610
4410
4510
4515
4610
---- 0000
---- 0000
---- uuuu
FSR2L
2410
2510
2515
2610
4410
4510
4515
4610
xxxx xxxx
uuuu uuuu
uuuu uuuu
STATUS
2410
2510
2515
2610
4410
4510
4515
4610
---x xxxx
---u uuuu
---u uuuu
TMR0H
2410
2510
2515
2610
4410
4510
4515
4610
0000 0000
0000 0000
uuuu uuuu
TMR0L
2410
2510
2515
2610
4410
4510
4515
4610
xxxx xxxx
uuuu uuuu
uuuu uuuu
T0CON
2410
2510
2515
2610
4410
4510
4515
4610
1111 1111
1111 1111
uuuu uuuu
OSCCON
2410
2510
2515
2610
4410
4510
4515
4610
0100 q000
0100 q000
uuuu uuqu
HLVDCON
2410
2510
2515
2610
4410
4510
4515
4610
0-00 0101
0-00 0101
u-uu uuuu
WDTCON
2410
2510
2515
2610
4410
4510
4515
4610
---- ---0
---- ---0
---- ---u
RCON(4)
2410
2510
2515
2610
4410
4510
4515
4610
0q-1 11q0
0q-q qquu
uq-u qquu
TMR1H
2410
2510
2515
2610
4410
4510
4515
4610
xxxx xxxx
uuuu uuuu
uuuu uuuu
TMR1L
2410
2510
2515
2610
4410
4510
4515
4610
xxxx xxxx
uuuu uuuu
uuuu uuuu
T1CON
2410
2510
2515
2610
4410
4510
4515
4610
0000 0000
u0uu uuuu
uuuu uuuu
TMR2
2410
2510
2515
2610
4410
4510
4515
4610
0000 0000
0000 0000
uuuu uuuu
PR2
2410
2510
2515
2610
4410
4510
4515
4610
1111 1111
1111 1111
1111 1111
T2CON
2410
2510
2515
2610
4410
4510
4515
4610
-000 0000
-000 0000
-uuu uuuu
SSPBUF
2410
2510
2515
2610
4410
4510
4515
4610
xxxx xxxx
uuuu uuuu
uuuu uuuu
SSPADD
2410
2510
2515
2610
4410
4510
4515
4610
0000 0000
0000 0000
uuuu uuuu
SSPSTAT
2410
2510
2515
2610
4410
4510
4515
4610
0000 0000
0000 0000
uuuu uuuu
SSPCON1
2410
2510
2515
2610
4410
4510
4515
4610
0000 0000
0000 0000
uuuu uuuu
SSPCON2
2410
2510
2515
2610
4410
4510
4515
4610
0000 0000
0000 0000
uuuu uuuu
Legend:
Note 1:
2:
3:
4:
5:
u = unchanged, x = unknown, - = unimplemented bit, read as ‘0’, q = value depends on condition.
Shaded cells indicate conditions do not apply for the designated device.
One or more bits in the INTCONx or PIRx registers will be affected (to cause wake-up).
When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the PC is loaded with the interrupt vector
(0008h or 0018h).
When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the TOSU, TOSH and TOSL are updated with
the current value of the PC. The STKPTR is modified to point to the next location in the hardware stack.
See Table 4-3 for Reset value for specific condition.
Bits 6 and 7 of PORTA, LATA and TRISA are enabled, depending on the oscillator mode selected. When not enabled as
PORTA pins, they are disabled and read ‘0’.
DS39636A-page 50
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
TABLE 4-4:
INITIALIZATION CONDITIONS FOR ALL REGISTERS (CONTINUED)
Register
Applicable Devices
Power-on Reset,
Brown-out
Reset
MCLR Resets,
WDT Reset,
RESET
Instruction,
Stack Resets
Wake-up via
WDT
or Interrupt
ADRESH
2410
2510
2515
2610
4410
4510
4515
4610
xxxx xxxx
uuuu uuuu
uuuu uuuu
ADRESL
2410
2510
2515
2610
4410
4510
4515
4610
xxxx xxxx
uuuu uuuu
uuuu uuuu
ADCON0
2410
2510
2515
2610
4410
4510
4515
4610
--00 0000
--00 0000
--uu uuuu
ADCON1
2410
2510
2515
2610
4410
4510
4515
4610
--00 0qqq
--00 0qqq
--uu uuuu
ADCON2
2410
2510
2515
2610
4410
4510
4515
4610
0-00 0000
0-00 0000
u-uu uuuu
CCPR1H
2410
2510
2515
2610
4410
4510
4515
4610
xxxx xxxx
uuuu uuuu
uuuu uuuu
CCPR1L
2410
2510
2515
2610
4410
4510
4515
4610
xxxx xxxx
uuuu uuuu
uuuu uuuu
CCP1CON
2410
2510
2515
2610
4410
4510
4515
4610
0000 0000
0000 0000
uuuu uuuu
2410
2510
2515
2610
4410
4510
4515
4610
--00 0000
--00 0000
--uu uuuu
CCPR2H
2410
2510
2515
2610
4410
4510
4515
4610
xxxx xxxx
uuuu uuuu
uuuu uuuu
CCPR2L
2410
2510
2515
2610
4410
4510
4515
4610
xxxx xxxx
uuuu uuuu
uuuu uuuu
CCP2CON
2410
2510
2515
2610
4410
4510
4515
4610
--00 0000
--00 0000
--uu uuuu
BAUDCON
2410
2510
2515
2610
4410
4510
4515
4610
01-0 0-00
01-0 0-00
--uu uuuu
PWM1CON
2410
2510
2515
2610
4410
4510
4515
4610
0000 0000
0000 0000
uuuu uuuu
ECCP1AS
2410
2510
2515
2610
4410
4510
4515
4610
0000 0000
0000 0000
uuuu uuuu
2410
2510
2515
2610
4410
4510
4515
4610
0000 00--
0000 00--
uuuu uu--
CVRCON
2410
2510
2515
2610
4410
4510
4515
4610
0000 0000
0000 0000
uuuu uuuu
CMCON
2410
2510
2515
2610
4410
4510
4515
4610
0000 0111
0000 0111
uuuu uuuu
TMR3H
2410
2510
2515
2610
4410
4510
4515
4610
xxxx xxxx
uuuu uuuu
uuuu uuuu
TMR3L
2410
2510
2515
2610
4410
4510
4515
4610
xxxx xxxx
uuuu uuuu
uuuu uuuu
T3CON
2410
2510
2515
2610
4410
4510
4515
4610
0000 0000
uuuu uuuu
uuuu uuuu
SPBRGH
2410
2510
2515
2610
4410
4510
4515
4610
0000 0000
0000 0000
uuuu uuuu
SPBRG
2410
2510
2515
2610
4410
4510
4515
4610
0000 0000
0000 0000
uuuu uuuu
RCREG
2410
2510
2515
2610
4410
4510
4515
4610
0000 0000
0000 0000
uuuu uuuu
TXREG
2410
2510
2515
2610
4410
4510
4515
4610
0000 0000
0000 0000
uuuu uuuu
TXSTA
2410
2510
2515
2610
4410
4510
4515
4610
0000 0010
0000 0010
uuuu uuuu
RCSTA
2410
2510
2515
2610
4410
4510
4515
4610
0000 000x
0000 000x
uuuu uuuu
Legend:
Note 1:
2:
3:
4:
5:
u = unchanged, x = unknown, - = unimplemented bit, read as ‘0’, q = value depends on condition.
Shaded cells indicate conditions do not apply for the designated device.
One or more bits in the INTCONx or PIRx registers will be affected (to cause wake-up).
When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the PC is loaded with the interrupt vector
(0008h or 0018h).
When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the TOSU, TOSH and TOSL are updated with
the current value of the PC. The STKPTR is modified to point to the next location in the hardware stack.
See Table 4-3 for Reset value for specific condition.
Bits 6 and 7 of PORTA, LATA and TRISA are enabled, depending on the oscillator mode selected. When not enabled as
PORTA pins, they are disabled and read ‘0’.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 51
PIC18F2X1X/4X1X
TABLE 4-4:
INITIALIZATION CONDITIONS FOR ALL REGISTERS (CONTINUED)
Register
Applicable Devices
Power-on Reset,
Brown-out
Reset
MCLR Resets,
WDT Reset,
RESET
Instruction,
Stack Resets
Wake-up via
WDT
or Interrupt
IPR2
2410
2510
2515
2610
4410
4510
4515
4610
11-- 1111
11-- 1111
uu-- uuuu
PIR2
2410
2510
2515
2610
4410
4510
4515
4610
00-- 0000
00-- 0000
uu-- uuuu(1)
PIE2
2410
2510
2515
2610
4410
4510
4515
4610
00-- 0000
00-- 0000
uu-- uuuu
uuuu uuuu
IPR1
PIR1
PIE1
2410
2510
2515
2610
4410
4510
4515
4610
1111 1111
1111 1111
2410
2510
2515
2610
4410
4510
4515
4610
-111 1111
-111 1111
-uuu uuuu
2410
2510
2515
2610
4410
4510
4515
4610
0000 0000
0000 0000
uuuu uuuu(1)
2410
2510
2515
2610
4410
4510
4515
4610
-000 0000
-000 0000
-uuu uuuu(1)
2410
2510
2515
2610
4410
4510
4515
4610
0000 0000
0000 0000
uuuu uuuu
2410
2510
2515
2610
4410
4510
4515
4610
-000 0000
-000 0000
-uuu uuuu
OSCTUNE
2410
2510
2515
2610
4410
4510
4515
4610
00-0 0000
00-0 0000
uu-u uuuu
TRISE
2410
2510
2515
2610
4410
4510
4515
4610
0000 -111
0000 -111
uuuu -uuu
TRISD
2410
2510
2515
2610
4410
4510
4515
4610
1111 1111
1111 1111
uuuu uuuu
TRISC
2410
2510
2515
2610
4410
4510
4515
4610
1111 1111
1111 1111
uuuu uuuu
TRISB
2410
2510
2515
2610
4410
4510
4515
4610
1111 1111
1111 1111
uuuu uuuu
TRISA(5)
2410
2510
2515
2610
4410
4510
4515
4610
1111 1111(5)
1111 1111(5)
uuuu uuuu(5)
LATE
2410
2510
2515
2610
4410
4510
4515
4610
---- -xxx
---- -uuu
---- -uuu
LATD
2410
2510
2515
2610
4410
4510
4515
4610
xxxx xxxx
uuuu uuuu
uuuu uuuu
LATC
2410
2510
2515
2610
4410
4510
4515
4610
xxxx xxxx
uuuu uuuu
uuuu uuuu
LATB
2410
2510
2515
2610
4410
4510
4515
4610
xxxx xxxx
uuuu uuuu
LATA
(5)
2410
2510
2515
2610
4410
4510
4515
4610
xxxx xxxx
(5)
uuuu uuuu
uuuu uuuu
(5)
uuuu uuuu(5)
PORTE
2410
2510
2515
2610
4410
4510
4515
4610
---- x000
---- x000
---- uuuu
PORTD
2410
2510
2515
2610
4410
4510
4515
4610
xxxx xxxx
uuuu uuuu
uuuu uuuu
PORTC
2410
2510
2515
2610
4410
4510
4515
4610
xxxx xxxx
uuuu uuuu
uuuu uuuu
PORTB
2410
2510
2515
2610
4410
4510
4515
4610
xxxx xxxx
uuuu uuuu
uuuu uuuu
PORTA(5)
2410
2510
2515
2610
4410
4510
4515
4610
xx0x 0000(5)
uu0u 0000(5)
uuuu uuuu(5)
Legend:
Note 1:
2:
3:
4:
5:
u = unchanged, x = unknown, - = unimplemented bit, read as ‘0’, q = value depends on condition.
Shaded cells indicate conditions do not apply for the designated device.
One or more bits in the INTCONx or PIRx registers will be affected (to cause wake-up).
When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the PC is loaded with the interrupt vector
(0008h or 0018h).
When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the TOSU, TOSH and TOSL are updated with
the current value of the PC. The STKPTR is modified to point to the next location in the hardware stack.
See Table 4-3 for Reset value for specific condition.
Bits 6 and 7 of PORTA, LATA and TRISA are enabled, depending on the oscillator mode selected. When not enabled as
PORTA pins, they are disabled and read ‘0’.
DS39636A-page 52
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
5.0
MEMORY ORGANIZATION
5.1
Program Memory Organization
PIC18 microcontrollers implement a 21-bit program
counter, which is capable of addressing a 2-Mbyte
program memory space. Accessing a location between
the upper boundary of the physically implemented
memory and the 2-Mbyte address will return all ‘0’s (a
NOP instruction).
There are two types of memory in PIC18F2X1X/4X1X
microcontroller devices:
• Program Memory
• Data RAM
As Harvard architecture devices, the data and program
memories use separate busses; this allows for
concurrent access of the two memory spaces.
The PIC18F2410/4410 and PIC18F2510 each have
16 Kbytes of Flash memory and can store up to 8,192
single-word instructions. The PIC18F2510/4510 each
have 32 Kbytes of Flash memory and can store up to
16,384 single-word instructions. The PIC18F2515/4515
each have 48 Kbytes of Flash memory and can store up
to 24,576 single-word instructions. The PIC18F2610/
4610 each have 64 Kbytes of Flash memory and can
store up to 32,768 single-word instructions.
Additional detailed information on the operation of the
Flash program memory is provided in Section 6.0
“Flash Program Memory”.
PIC18 devices have two interrupt vectors. The Reset
vector address is at 0000h and the interrupt vector
addresses are at 0008h and 0018h.
The program memory map for PIC18F2X1X/4X1X
devices is shown in Figure 5-1.
FIGURE 5-1:
PROGRAM MEMORY MAP AND STACK FOR
PIC18F2X1X/4X1X DEVICES
PC<20:0>
CALL,RCALL,RETURN
RETFIE,RETLW
Stack Level 1
21
•
•
•
Stack Level 31
On-Chip
Program Memory
(16 Kbytes)
Reset Vector
00000h
High Priority Interrupt Vector
00008h
Low Priority Interrupt Vector
00018h
On-Chip
Program Memory
(32 Kbytes)
On-Chip
Program Memory
(48 Kbytes)
On-Chip
Program Memory
(64 Kbytes)
User Memory Space
03FFFh
04000h
07FFFh
08000h
0BFFFh
0C000h
0FFFFh
10000h
Read ‘0’
Read ‘0’
Read ‘0’
Read ‘0’
PIC18F2410/4410
PIC18F2510/4510
PIC18F2515/4515
PIC18F2610/4610
 2004 Microchip Technology Inc.
Preliminary
1FFFFFh
200000h
DS39636A-page 53
PIC18F2X1X/4X1X
5.1.1
PROGRAM COUNTER
The Program Counter (PC) specifies the address of the
instruction to fetch for execution. The PC is 21 bits wide
and is contained in three separate 8-bit registers. The
low byte, known as the PCL register, is both readable
and writable. The high byte, or PCH register, contains
the PC<15:8> bits; it is not directly readable or writable.
Updates to the PCH register are performed through the
PCLATH register. The upper byte is called PCU. This
register contains the PC<20:16> bits; it is also not
directly readable or writable. Updates to the PCU
register are performed through the PCLATU register.
The contents of PCLATH and PCLATU are transferred
to the program counter by any operation that writes
PCL. Similarly, the upper two bytes of the program
counter are transferred to PCLATH and PCLATU by an
operation that reads PCL. This is useful for computed
offsets to the PC (see Section 5.1.4.1 “Computed
GOTO”).
The PC addresses bytes in the program memory. To
prevent the PC from becoming misaligned with word
instructions, the Least Significant bit of PCL is fixed to
a value of ‘0’. The PC increments by 2 to address
sequential instructions in the program memory.
The CALL, RCALL, GOTO and program branch
instructions write to the program counter directly. For
these instructions, the contents of PCLATH and
PCLATU are not transferred to the program counter.
5.1.2
RETURN ADDRESS STACK
The return address stack allows any combination of up
to 31 program calls and interrupts to occur. The PC is
pushed onto the stack when a CALL or RCALL instruction is executed or an interrupt is Acknowledged. The
PC value is pulled off the stack on a RETURN, RETLW or
a RETFIE instruction. PCLATU and PCLATH are not
affected by any of the RETURN or CALL instructions.
FIGURE 5-2:
The stack operates as a 31-word by 21-bit RAM and a
5-bit Stack Pointer, STKPTR. The stack space is not
part of either program or data space. The Stack Pointer
is readable and writable and the address on the top of
the stack is readable and writable through the top-ofstack Special File Registers. Data can also be pushed
to, or popped from the stack, using these registers.
A CALL type instruction causes a push onto the stack;
the Stack Pointer is first incremented and the location
pointed to by the Stack Pointer is written with the
contents of the PC (already pointing to the instruction
following the CALL). A RETURN type instruction causes
a pop from the stack; the contents of the location
pointed to by the STKPTR are transferred to the PC
and then the Stack Pointer is decremented.
The Stack Pointer is initialized to ‘00000’ after all
Resets. There is no RAM associated with the location
corresponding to a Stack Pointer value of ‘00000’; this
is only a Reset value. Status bits indicate if the stack is
full or has overflowed or has underflowed.
5.1.2.1
Top-of-Stack Access
Only the top of the return address stack (TOS) is
readable and writable. A set of three registers,
TOSU:TOSH:TOSL, hold the contents of the stack location pointed to by the STKPTR register (Figure 5-2). This
allows users to implement a software stack if necessary.
After a CALL, RCALL or interrupt, the software can read
the pushed value by reading the TOSU:TOSH:TOSL
registers. These values can be placed on a user defined
software stack. At return time, the software can return
these values to TOSU:TOSH:TOSL and do a return.
The user must disable the global interrupt enable bits
while accessing the stack to prevent inadvertent stack
corruption.
RETURN ADDRESS STACK AND ASSOCIATED REGISTERS
Return Address Stack <20:0>
11111
11110
11101
Top-of-Stack Registers
TOSU
00h
TOSH
1Ah
STKPTR<4:0>
00010
TOSL
34h
Top-of-Stack
DS39636A-page 54
Stack Pointer
001A34h
000D58h
Preliminary
00011
00010
00001
00000
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
5.1.2.2
Return Stack Pointer (STKPTR)
When the stack has been popped enough times to
unload the stack, the next pop will return a value of zero
to the PC and sets the STKUNF bit, while the Stack
Pointer remains at zero. The STKUNF bit will remain
set until cleared by software or until a POR occurs.
The STKPTR register (Register 5-1) contains the Stack
Pointer value, the STKFUL (Stack Full) status bit and
the STKUNF (Stack Underflow) status bits. The value
of the Stack Pointer can be 0 through 31. The Stack
Pointer increments before values are pushed onto the
stack and decrements after values are popped off the
stack. On Reset, the Stack Pointer value will be zero.
The user may read and write the Stack Pointer value.
This feature can be used by a Real-Time Operating
System (RTOS) for return stack maintenance.
Note:
After the PC is pushed onto the stack 31 times (without
popping any values off the stack), the STKFUL bit is
set. The STKFUL bit is cleared by software or by a
POR.
5.1.2.3
PUSH and POP Instructions
Since the Top-of-Stack is readable and writable, the
ability to push values onto the stack and pull values off
the stack without disturbing normal program execution
is a desirable feature. The PIC18 instruction set
includes two instructions, PUSH and POP, that permit
the TOS to be manipulated under software control.
TOSU, TOSH and TOSL can be modified to place data
or a return address on the stack.
The action that takes place when the stack becomes
full depends on the state of the STVREN (Stack Overflow Reset Enable) configuration bit. (Refer to
Section 22.1 “Configuration Bits” for a description of
the device configuration bits.) If STVREN is set
(default), the 31st push will push the (PC + 2) value
onto the stack, set the STKFUL bit and reset the
device. The STKFUL bit will remain set and the Stack
Pointer will be set to zero.
The PUSH instruction places the current PC value onto
the stack. This increments the Stack Pointer and loads
the current PC value onto the stack.
If STVREN is cleared, the STKFUL bit will be set on the
31st push and the Stack Pointer will increment to 31.
Any additional pushes will not overwrite the 31st push
and STKPTR will remain at 31.
REGISTER 5-1:
Returning a value of zero to the PC on an
underflow has the effect of vectoring the
program to the Reset vector, where the
stack conditions can be verified and
appropriate actions can be taken. This is
not the same as a Reset, as the contents
of the SFRs are not affected.
The POP instruction discards the current TOS by decrementing the Stack Pointer. The previous value pushed
onto the stack then becomes the TOS value.
STKPTR: STACK POINTER REGISTER
R/C-0
R/C-0
U-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
STKFUL(1)
STKUNF(1)
—
SP4
SP3
SP2
SP1
SP0
bit 7
bit 0
bit 7
STKFUL: Stack Full Flag bit(1)
1 = Stack became full or overflowed
0 = Stack has not become full or overflowed
bit 6
STKUNF: Stack Underflow Flag bit(1)
1 = Stack underflow occurred
0 = Stack underflow did not occur
bit 5
Unimplemented: Read as ‘0’
bit 4-0
SP4:SP0: Stack Pointer Location bits
Note 1: Bit 7 and bit 6 are cleared by user software or by a POR.
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented
C = Clearable only bit
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 55
PIC18F2X1X/4X1X
5.1.2.4
Stack Full and Underflow Resets
5.1.4
Device Resets on stack overflow and stack underflow
conditions are enabled by setting the STVREN bit in
Configuration Register 4L. When STVREN is set, a full
or underflow will set the appropriate STKFUL or
STKUNF bit and then cause a device Reset. When
STVREN is cleared, a full or underflow condition will set
the appropriate STKFUL or STKUNF bit but not cause
a device Reset. The STKFUL or STKUNF bits are
cleared by the user software or a Power-on Reset.
5.1.3
FAST REGISTER STACK
A fast register stack is provided for the Status, WREG
and BSR registers, to provide a “fast return” option for
interrupts. The stack for each register is only one level
deep and is neither readable nor writable. It is loaded
with the current value of the corresponding register
when the processor vectors for an interrupt. All interrupt sources will push values into the stack registers.
The values in the registers are then loaded back into
their associated registers if the RETFIE, FAST
instruction is used to return from the interrupt.
LOOK-UP TABLES IN PROGRAM
MEMORY
There may be programming situations that require the
creation of data structures, or look-up tables, in
program memory. For PIC18 devices, look-up tables
can be implemented in two ways:
• Computed GOTO
• Table Reads
5.1.4.1
Computed GOTO
A computed GOTO is accomplished by adding an offset
to the program counter. An example is shown in
Example 5-2.
A look-up table can be formed with an ADDWF PCL
instruction and a group of RETLW nn instructions. The
W register is loaded with an offset into the table before
executing a call to that table. The first instruction of the
called routine is the ADDWF PCL instruction. The next
instruction executed will be one of the RETLW nn
instructions that returns the value ‘nn’ to the calling
function.
If both low and high priority interrupts are enabled, the
stack registers cannot be used reliably to return from
low priority interrupts. If a high priority interrupt occurs
while servicing a low priority interrupt, the stack register
values stored by the low priority interrupt will be
overwritten. In these cases, users must save the key
registers in software during a low priority interrupt.
The offset value (in WREG) specifies the number of
bytes that the program counter should advance and
should be multiples of 2 (LSb = 0).
If interrupt priority is not used, all interrupts may use the
fast register stack for returns from interrupt. If no interrupts are used, the fast register stack can be used to
restore the Status, WREG and BSR registers at the end
of a subroutine call. To use the fast register stack for a
subroutine call, a CALL label, FAST instruction must
be executed to save the Status, WREG and BSR registers to the fast register stack. A RETURN, FAST
instruction is then executed to restore these registers
from the fast register stack.
EXAMPLE 5-2:
Example 5-1 shows a source code example that uses
the fast register stack during a subroutine call and
return.
EXAMPLE 5-1:
CALL SUB1, FAST
FAST REGISTER STACK
CODE EXAMPLE
;STATUS, WREG, BSR
;SAVED IN FAST REGISTER
;STACK
•
•
•
•
RETURN, FAST
SUB1
DS39636A-page 56
;RESTORE VALUES SAVED
;IN FAST REGISTER STACK
In this method, only one data byte may be stored in
each instruction location and room on the return
address stack is required.
ORG
TABLE
5.1.4.2
MOVF
CALL
nn00h
ADDWF
RETLW
RETLW
RETLW
.
.
.
COMPUTED GOTO USING
AN OFFSET VALUE
OFFSET, W
TABLE
PCL
nnh
nnh
nnh
Table Reads and Table Writes
A better method of storing data in program memory
allows two bytes of data to be stored in each instruction
location.
Look-up table data may be stored two bytes per
program word by using table reads and writes. The
Table Pointer (TBLPTR) register specifies the byte
address and the Table Latch (TABLAT) register
contains the data that is read from or written to program
memory. Data is transferred to or from program
memory one byte at a time.
Table read and table write operations are discussed
further in Section 6.1 “Table Reads”.
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
5.2
5.2.2
PIC18 Instruction Cycle
5.2.1
An “Instruction Cycle” consists of four Q cycles: Q1
through Q4. The instruction fetch and execute are
pipelined in such a manner that a fetch takes one
instruction cycle, while the decode and execute take
another instruction cycle. However, due to the pipelining, each instruction effectively executes in one
cycle. If an instruction causes the program counter to
change (e.g., GOTO), then two cycles are required to
complete the instruction (Example 5-3).
CLOCKING SCHEME
The microcontroller clock input, whether from an
internal or external source, is internally divided by four
to generate four non-overlapping quadrature clocks
(Q1, Q2, Q3 and Q4). Internally, the program counter is
incremented on every Q1; the instruction is fetched
from the program memory and latched into the instruction register during Q4. The instruction is decoded and
executed during the following Q1 through Q4. The
clocks and instruction execution flow are shown in
Figure 5-3.
FIGURE 5-3:
INSTRUCTION FLOW/PIPELINING
A fetch cycle begins with the Program Counter (PC)
incrementing in Q1.
In the execution cycle, the fetched instruction is latched
into the Instruction Register (IR) in cycle Q1. This
instruction is then decoded and executed during the
Q2, Q3 and Q4 cycles. Data memory is read during Q2
(operand read) and written during Q4 (destination
write).
CLOCK/INSTRUCTION CYCLE
Q1
Q2
Q3
Q4
Q1
Q2
Q3
Q4
Q2
Q1
Q3
Q4
OSC1
Q1
Q2
Internal
Phase
Clock
Q3
Q4
PC
PC
PC + 2
PC + 4
OSC2/CLKO
(RC mode)
Execute INST (PC – 2)
Fetch INST (PC)
EXAMPLE 5-3:
TCY0
TCY1
Fetch 1
Execute 1
2. MOVWF PORTB
4. BSF
Execute INST (PC + 2)
Fetch INST (PC + 4)
INSTRUCTION PIPELINE FLOW
1. MOVLW 55h
3. BRA
Execute INST (PC)
Fetch INST (PC + 2)
SUB_1
Fetch 2
TCY2
TCY3
TCY4
TCY5
Execute 2
Fetch 3
Execute 3
Fetch 4
PORTA, BIT3 (Forced NOP)
Flush (NOP)
Fetch SUB_1 Execute SUB_1
5. Instruction @ address SUB_1
All instructions are single cycle, except for any program branches. These take two cycles since the fetch instruction
is “flushed” from the pipeline while the new instruction is being fetched and then executed.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 57
PIC18F2X1X/4X1X
5.2.3
INSTRUCTIONS IN PROGRAM
MEMORY
The program memory is addressed in bytes. Instructions are stored as two bytes or four bytes in program
memory. The Least Significant Byte of an instruction
word is always stored in a program memory location
with an even address (LSb = 0). To maintain alignment
with instruction boundaries, the PC increments in steps
of 2 and the LSb will always read ‘0’ (see Section 5.1.1
“Program Counter”).
Figure 5-4 shows an example of how instruction words
are stored in the program memory.
FIGURE 5-4:
The CALL and GOTO instructions have the absolute
program memory address embedded into the instruction. Since instructions are always stored on word
boundaries, the data contained in the instruction is a
word address. The word address is written to PC<20:1>,
which accesses the desired byte address in program
memory. Instruction #2 in Figure 5-4 shows how the
instruction GOTO 0006h is encoded in the program
memory. Program branch instructions, which encode a
relative address offset, operate in the same manner. The
offset value stored in a branch instruction represents the
number of single-word instructions that the PC will be
offset by. Section 23.0 “Instruction Set Summary”
provides further details of the instruction set.
INSTRUCTIONS IN PROGRAM MEMORY
LSB = 1
LSB = 0
0Fh
EFh
F0h
C1h
F4h
55h
03h
00h
23h
56h
Program Memory
Byte Locations →
5.2.4
Instruction 1:
Instruction 2:
MOVLW
GOTO
055h
0006h
Instruction 3:
MOVFF
123h, 456h
TWO-WORD INSTRUCTIONS
The standard PIC18 instruction set has four two-word
instructions: CALL, MOVFF, GOTO and LSFR. In all
cases, the second word of the instructions always has
‘1111’ as its four Most Significant bits; the other 12 bits
are literal data, usually a data memory address.
some reason and the second word is executed by itself,
a NOP is executed instead. This is necessary for cases
when the two-word instruction is preceded by a conditional instruction that changes the PC. Example 5-4
shows how this works.
Note:
The use of ‘1111’ in the 4 MSbs of an instruction specifies a special form of NOP. If the instruction is executed
in proper sequence – immediately after the first word –
the data in the second word is accessed and used by
the instruction sequence. If the first word is skipped for
EXAMPLE 5-4:
CASE 1:
Object Code
0110 0110 0000
1100 0001 0010
1111 0100 0101
0010 0100 0000
CASE 2:
Object Code
0110 0110 0000
1100 0001 0010
1111 0100 0101
0010 0100 0000
DS39636A-page 58
Word Address
↓
000000h
000002h
000004h
000006h
000008h
00000Ah
00000Ch
00000Eh
000010h
000012h
000014h
See Section 5.6 “PIC18 Instruction
Execution and the Extended Instruction Set” for information on two-word
instructions in the extended instruction
set.
TWO-WORD INSTRUCTIONS
0000
0011
0110
0000
Source Code
TSTFSZ
REG1
; is RAM location 0?
MOVFF
REG1, REG2 ; No, skip this word
; Execute this word as a NOP
ADDWF
REG3
; continue code
0000
0011
0110
0000
Source Code
TSTFSZ
REG1
; is RAM location 0?
MOVFF
REG1, REG2 ; Yes, execute this word
; 2nd word of instruction
ADDWF
REG3
; continue code
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
5.3
Note:
5.3.1
Data Memory Organization
The operation of some aspects of data
memory are changed when the PIC18
extended instruction set is enabled. See
Section 5.5 “Data Memory and the
Extended Instruction Set” for more
information.
The data memory in PIC18 devices is implemented as
static RAM. Figures 5-5, 5-6 and 5-7 show the data
memory organization for the PIC18F2X1X/4X1X
devices.
The data memory contains Special Function Registers
(SFRs) and General Purpose Registers (GPRs). The
SFRs are used for control and status of the controller
and peripheral functions, while GPRs are used for data
storage and scratchpad operations in the user’s
application. Any read of an unimplemented location will
read as ‘0’s.
The instruction set and architecture allow operations
across all banks. The entire data memory may be
accessed by Direct, Indirect or Indexed Addressing
modes. Addressing modes are discussed later in this
subsection.
To ensure that commonly used registers (SFRs and
select GPRs) can be accessed in a single cycle, PIC18
devices implement an Access Bank. This is a 256-byte
memory space that provides fast access to SFRs and
the lower portion of GPR Bank 0 without using the
BSR. Section 5.3.2 “Access Bank” provides a
detailed description of the Access RAM.
BANK SELECT REGISTER (BSR)
Large areas of data memory require an efficient
addressing scheme to make rapid access to any
address possible. Ideally, this means that an entire
address does not need to be provided for each read or
write operation. For PIC18 devices, this is accomplished with a RAM banking scheme. This divides the
memory space into 16 contiguous banks of 256 bytes.
Depending on the instruction, each location can be
addressed directly by its full 12-bit address, or an 8-bit
low-order address and a 4-bit bank pointer.
Most instructions in the PIC18 instruction set make use
of the bank pointer, known as the Bank Select Register
(BSR). This SFR holds the 4 Most Significant bits of a
location’s address; the instruction itself includes the
8 Least Significant bits. Only the four lower bits of the
BSR are implemented (BSR3:BSR0). The upper four
bits are unused; they will always read ‘0’ and cannot be
written to. The BSR can be loaded directly by using the
MOVLB instruction.
The value of the BSR indicates the bank in data
memory; the 8 bits in the instruction show the location
in the bank and can be thought of as an offset from the
bank’s lower boundary. The relationship between the
BSR’s value and the bank division in data memory is
shown in Figure 5-8.
Since up to 16 registers may share the same low-order
address, the user must always be careful to ensure that
the proper bank is selected before performing a data
read or write. For example, writing what should be
program data to an 8-bit address of F9h, while the BSR
is 0Fh, will end up resetting the program counter.
While any bank can be selected, only those banks that
are actually implemented can be read or written to.
Writes to unimplemented banks are ignored, while
reads from unimplemented banks will return ‘0’s. Even
so, the Status register will still be affected as if the
operation was successful. The data memory map in
Figure 5-5 indicates which banks are implemented.
In the core PIC18 instruction set, only the MOVFF
instruction fully specifies the 12-bit address of the
source and target registers. This instruction ignores the
BSR completely when it executes. All other instructions
include only the low-order address as an operand and
must use either the BSR or the Access Bank to locate
their target registers.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 59
PIC18F2X1X/4X1X
FIGURE 5-5:
DATA MEMORY MAP FOR PIC18F2410/4410 DEVICES
BSR<3:0>
= 0000
00h
Access RAM
FFh
00h
GPR
Bank 0
= 0001
= 0011
= 0100
= 0101
= 0110
= 0111
= 1000
= 1001
= 1010
= 1011
= 1100
= 1101
= 1110
= 1111
DS39636A-page 60
1FFh
200h
FFh
00h
Bank 2
Bank 3
Bank 4
Bank 5
000h
07Fh
080h
0FFh
100h
GPR
Bank 1
= 0010
When ‘a’ = 0:
Data Memory Map
The BSR is ignored and the
Access Bank is used.
The first 128 bytes are
general purpose RAM
(from Bank 0).
The second 128 bytes are
Special Function Registers
(from Bank 15).
GPR
FFh
00h
2FFh
300h
FFh
00h
3FFh
400h
FFh
00h
4FFh
500h
FFh
00h
5FFh
600h
FFh
00h
6FFh
700h
When ‘a’ = 1:
The BSR specifies the Bank
used by the instruction.
Bank 6
Bank 7
Bank 8
Bank 9
7FFh
800h
FFh
00h
FFh
00h
Unused
Read 00h
9FFh
A00h
FFh
00h
AFFh
B00h
FFh
00h
BFFh
C00h
FFh
Bank 13 00h
CFFh
D00h
FFh
00h
DFFh
E00h
Bank 11
Bank 12
Access RAM Low
00h
7Fh
Access RAM High 80h
(SFRs)
FFh
8FFh
900h
FFh
00h
Bank 10
Access Bank
Bank 14
FFh
00h
Unused
FFh
SFR
Bank 15
EFFh
F00h
F7Fh
F80h
FFFh
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
FIGURE 5-6:
DATA MEMORY MAP FOR PIC18F2510/4510 DEVICES
BSR<3:0>
= 0000
00h
Access RAM
FFh
00h
GPR
Bank 0
= 0001
= 0011
= 0100
= 0101
= 0110
= 0111
= 1000
= 1001
= 1010
= 1011
= 1100
= 1101
= 1110
= 1111
1FFh
200h
FFh
00h
Bank 2
Bank 3
Bank 4
Bank 5
000h
07Fh
080h
0FFh
100h
GPR
Bank 1
= 0010
When ‘a’ = 0:
Data Memory Map
The BSR is ignored and the
Access Bank is used.
The first 128 bytes are
general purpose RAM
(from Bank 0).
The second 128 bytes are
Special Function Registers
(from Bank 15).
GPR
FFh
00h
2FFh
300h
GPR
3FFh
400h
FFh
00h
When ‘a’ = 1:
The BSR specifies the Bank
used by the instruction.
GPR
4FFh
500h
FFh
00h
GPR
FFh
00h
5FFh
600h
FFh
00h
6FFh
700h
Bank 6
Bank 7
Bank 8
Bank 9
Bank 10
FFh
00h
7FFh
800h
FFh
00h
8FFh
900h
FFh
00h
Unused
Read 00h
AFFh
B00h
FFh
00h
BFFh
C00h
FFh
Bank 13 00h
CFFh
D00h
FFh
00h
DFFh
E00h
Bank 12
Access RAM Low
00h
7Fh
Access RAM High 80h
(SFRs)
FFh
9FFh
A00h
FFh
00h
Bank 11
Access Bank
Bank 14
FFh
00h
Unused
FFh
SFR
Bank 15
 2004 Microchip Technology Inc.
EFFh
F00h
F7Fh
F80h
FFFh
Preliminary
DS39636A-page 61
PIC18F2X1X/4X1X
FIGURE 5-7:
DATA MEMORY MAP FOR PIC18F2515/2610/4515/4610 DEVICES
BSR<3:0>
= 0000
00h
Access RAM
FFh
00h
GPR
Bank 0
= 0001
= 0011
= 0100
= 0101
= 0110
= 0111
= 1000
= 1001
= 1010
= 1011
= 1100
= 1101
= 1110
= 1111
DS39636A-page 62
1FFh
200h
FFh
00h
Bank 2
Bank 3
Bank 4
Bank 5
2FFh
300h
GPR
3FFh
400h
FFh
00h
Bank 12
When a = 1:
The BSR specifies the Bank
used by the instruction.
GPR
5FFh
600h
GPR
Bank 7
Bank 11
The second 128 bytes are
Special Function Registers
(from Bank 15).
4FFh
500h
FFh
00h
Bank 10
The first 128 bytes are
general purpose RAM
(from Bank 0).
GPR
FFh
00h
Bank 6
Bank 9
The BSR is ignored and the
Access Bank is used.
GPR
FFh
00h
FFh
00h
Bank 8
000h
07Fh
080h
0FFh
100h
GPR
Bank 1
= 0010
When a = 0:
Data Memory Map
6FFh
700h
GPR
7FFh
800h
FFh
00h
GPR
Access Bank
Access RAM Low
00h
7Fh
Access RAM High 80h
(SFRs)
FFh
8FFh
900h
FFh
00h
GPR
9FFh
A00h
FFh
00h
GPR
AFFh
B00h
FFh
00h
GPR
FFh
00h
FFh
Bank 13 00h
FFh
00h
Bank 14
BFFh
C00h
GPR
CFFh
D00h
GPR
DFFh
E00h
GPR
FFh
00h
GPR
FFh
SFR
Bank 15
EFFh
F00h
F7Fh
F80h
FFFh
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
FIGURE 5-8:
USE OF THE BANK SELECT REGISTER (DIRECT ADDRESSING)
0
Data Memory
BSR(1)
7
0
0
0
0
0
0
1
1
000h
00h
Bank 0
FFh
00h
100h
Bank 1
Bank Select(2)
From Opcode(2)
7
1
1
1
1
1
1
0
1
1
FFh
00h
200h
Bank 2
FFh
00h
300h
Bank 3
through
Bank 13
FFh
00h
E00h
Bank 14
FFh
00h
F00h
Bank 15
FFFh
Note 1:
2:
5.3.2
FFh
The Access RAM bit of the instruction can be used to force an override of the selected bank (BSR<3:0>) to
the registers of the Access Bank.
The MOVFF instruction embeds the entire 12-bit address in the instruction.
ACCESS BANK
While the use of the BSR with an embedded 8-bit
address allows users to address the entire range of
data memory, it also means that the user must always
ensure that the correct bank is selected. Otherwise,
data may be read from or written to the wrong location.
This can be disastrous if a GPR is the intended target
of an operation, but an SFR is written to instead.
Verifying and/or changing the BSR for each read or
write to data memory can become very inefficient.
To streamline access for the most commonly used data
memory locations, the data memory is configured with
an Access Bank, which allows users to access a
mapped block of memory without specifying a BSR.
The Access Bank consists of the first 128 bytes of
memory (00h-7Fh) in Bank 0 and the last 128 bytes of
memory (80h-FFh) in Block 15. The lower half is known
as the “Access RAM” and is composed of GPRs. This
upper half is also where the device’s SFRs are
mapped. These two areas are mapped contiguously in
the Access Bank and can be addressed in a linear
fashion by an 8-bit address (Figure 5-5).
The Access Bank is used by core PIC18 instructions
that include the Access RAM bit (the ‘a’ parameter in
the instruction). When ‘a’ is equal to ‘1’, the instruction
uses the BSR and the 8-bit address included in the
opcode for the data memory address. When ‘a’ is ‘0’,
however, the instruction is forced to use the Access
Bank address map; the current value of the BSR is
ignored entirely.
 2004 Microchip Technology Inc.
Using this “forced” addressing allows the instruction to
operate on a data address in a single cycle, without
updating the BSR first. For 8-bit addresses of 80h and
above, this means that users can evaluate and operate
on SFRs more efficiently. The Access RAM below 80h
is a good place for data values that the user might need
to access rapidly, such as immediate computational
results or common program variables. Access RAM
also allows for faster and more code efficient context
saving and switching of variables.
The mapping of the Access Bank is slightly different
when the extended instruction set is enabled (XINST
configuration bit = 1). This is discussed in more detail
in Section 5.5.3 “Mapping the Access Bank in
Indexed Literal Offset Addressing Mode”.
5.3.3
GENERAL PURPOSE REGISTER
FILE
PIC18 devices may have banked memory in the GPR
area. This is data RAM, which is available for use by all
instructions. GPRs start at the bottom of Bank 0
(address 000h) and grow upwards towards the bottom of
the SFR area. GPRs are not initialized by a Power-on
Reset and are unchanged on all other Resets.
Preliminary
DS39636A-page 63
PIC18F2X1X/4X1X
5.3.4
SPECIAL FUNCTION REGISTERS
The SFRs can be classified into two sets: those associated with the “core” device functionality (ALU, Resets
and interrupts) and those related to the peripheral functions. The reset and interrupt registers are described in
their respective chapters, while the ALU’s Status register is described later in this section. Registers related to
the operation of a peripheral feature are described in
the chapter for that peripheral.
The Special Function Registers (SFRs) are registers
used by the CPU and peripheral modules for controlling
the desired operation of the device. These registers are
implemented as static RAM. SFRs start at the top of
data memory (FFFh) and extend downward to occupy
the top half of Bank 15 (F80h to FFFh). A list of these
registers is given in Table 5-1 and Table 5-2.
TABLE 5-1:
The SFRs are typically distributed among the
peripherals whose functions they control. Unused SFR
locations are unimplemented and read as ‘0’s.
SPECIAL FUNCTION REGISTER MAP FOR PIC18F2X1X/4X1X DEVICES
Address
Name
FFFh
TOSU
Address
Name
Address
FDFh
INDF2(1)
POSTINC2(1)
FBEh
FBDh
FDCh
PREINC2
(1)
FBCh
FFEh
TOSH
FDEh
FFDh
TOSL
FDDh POSTDEC2(1)
FFCh
STKPTR
FFBh
PCLATU
FDBh
PLUSW2(1)
FFAh
PCLATH
FDAh
FSR2H
FBFh
Name
Address
CCPR1H
Name
F9Fh
IPR1
CCPR1L
F9Eh
PIR1
CCP1CON
F9Dh
PIE1
CCPR2H
F9Ch
—(2)
FBBh
CCPR2L
F9Bh
OSCTUNE
FBAh
CCP2CON
F9Ah
—(2)
F99h
—(2)
FF9h
PCL
FD9h
FSR2L
FB9h
—(2)
FF8h
TBLPTRU
FD8h
STATUS
FB8h
BAUDCON
F98h
—(2)
F97h
—(2)
FF7h
TBLPTRH
FD7h
TMR0H
FB7h
PWM1CON(3)
FF6h
TBLPTRL
FD6h
TMR0L
FB6h
ECCP1AS(3)
F96h
TRISE(3)
FF5h
TABLAT
FD5h
T0CON
FB5h
CVRCON
F95h
TRISD(3)
FF4h
PRODH
FD4h
—(2)
FB4h
CMCON
F94h
TRISC
FF3h
PRODL
FD3h
OSCCON
FB3h
TMR3H
F93h
TRISB
FF2h
INTCON
FD2h
HLVDCON
FB2h
TMR3L
F92h
TRISA
FF1h
INTCON2
FD1h
WDTCON
FB1h
T3CON
F91h
—(2)
FF0h
INTCON3
FD0h
RCON
FB0h
SPBRGH
F90h
—(2)
FEFh
INDF0(1)
FCFh
TMR1H
FAFh
SPBRG
F8Fh
—(2)
FEEh POSTINC0(1)
FCEh
TMR1L
FAEh
RCREG
F8Eh
—(2)
FEDh
POSTDEC0(1)
FCDh
T1CON
FADh
TXREG
F8Dh
LATE(3)
FECh
PREINC0(1)
FCCh
TMR2
FACh
TXSTA
F8Ch
LATD(3)
FEBh
PLUSW0(1)
FCBh
PR2
FABh
RCSTA
F8Bh
LATC
FEAh
FSR0H
FCAh
T2CON
FAAh
—(2)
F8Ah
LATB
FE9h
FSR0L
FC9h
SSPBUF
FA9h
—(2)
F89h
LATA
FA8h
—(2)
F88h
—(2)
F87h
—(2)
FE8h
WREG
FE7h
INDF1(1)
FE6h POSTINC1(1)
FC8h
SSPADD
FC7h
SSPSTAT
FA7h
—(2)
FC6h
SSPCON1
FA6h
—(2)
F86h
—(2)
F85h
—(2)
FE5h
POSTDEC1(1)
FC5h
SSPCON2
FA5h
—(2)
FE4h
PREINC1(1)
FC4h
ADRESH
FA4h
—(2)
F84h
PORTE(3)
FE3h
PLUSW1(1)
FC3h
ADRESL
FA3h
—(2)
F83h
PORTD(3)
FE2h
FSR1H
FC2h
ADCON0
FA2h
IPR2
F82h
PORTC
FE1h
FSR1L
FC1h
ADCON1
FA1h
PIR2
F81h
PORTB
FE0h
BSR
FC0h
ADCON2
FA0h
PIE2
F80h
PORTA
Note 1:
2:
3:
This is not a physical register.
Unimplemented registers are read as ‘0’.
This register is not available on 28-pin devices.
DS39636A-page 64
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
TABLE 5-2:
File Name
REGISTER FILE SUMMARY (PIC18F2X1X/4X1X)
Bit 7
Bit 6
Bit 5
—
—
—
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Details
on page:
---0 0000
49, 54
TOSH
Top-of-Stack High Byte (TOS<15:8>)
0000 0000
49, 54
TOSL
Top-of-Stack Low Byte (TOS<7:0>)
0000 0000
49, 54
00-0 0000
49, 55
TOSU
STKPTR
PCLATU
STKFUL(6)
STKUNF(6)
—
—
—
—
Top-of-Stack Upper Byte (TOS<20:16>)
Value on
POR, BOR
SP4
SP3
SP2
SP1
SP0
---0 0000
49, 54
PCLATH
Holding Register for PC<15:8>
0000 0000
49, 54
PCL
PC Low Byte (PC<7:0>)
0000 0000
49, 54
--00 0000
49, 77
TBLPTRU
—
—
bit 21
Holding Register for PC<20:16>
Program Memory Table Pointer Upper Byte (TBLPTR<20:16>)
TBLPTRH
Program Memory Table Pointer High Byte (TBLPTR<15:8>)
0000 0000
49, 77
TBLPTRL
Program Memory Table Pointer Low Byte (TBLPTR<7:0>)
0000 0000
49, 77
TABLAT
Program Memory Table Latch
0000 0000
49, 77
PRODH
Product Register High Byte
xxxx xxxx
49, 79
PRODL
Product Register Low Byte
xxxx xxxx
49, 79
INTCON
GIE/GIEH
PEIE/GIEL
TMR0IE
INT0IE
RBIE
TMR0IF
INT0IF
RBIF
0000 000x
49, 83
INTCON2
RBPU
INTEDG0
INTEDG1
INTEDG2
—
TMR0IP
—
RBIP
1111 -1-1
49, 84
INT2IP
INT1IP
—
INT2IE
INT1IE
—
INT2IF
INT1IF
11-0 0-00
49, 85
INTCON3
INDF0
Uses contents of FSR0 to address data memory – value of FSR0 not changed (not a physical register)
N/A
49, 70
POSTINC0
Uses contents of FSR0 to address data memory – value of FSR0 post-incremented (not a physical register)
N/A
49, 70
POSTDEC0
Uses contents of FSR0 to address data memory – value of FSR0 post-decremented (not a physical register)
N/A
49, 70
PREINC0
Uses contents of FSR0 to address data memory – value of FSR0 pre-incremented (not a physical register)
N/A
49, 70
PLUSW0
Uses contents of FSR0 to address data memory – value of FSR0 pre-incremented (not a physical register) –
value of FSR0 offset by W
N/A
49, 70
FSR0H
---- 0000
49, 70
FSR0L
Indirect Data Memory Address Pointer 0 Low Byte
—
xxxx xxxx
49, 70
WREG
Working Register
xxxx xxxx
49
INDF1
Uses contents of FSR1 to address data memory – value of FSR1 not changed (not a physical register)
N/A
49, 70
POSTINC1
Uses contents of FSR1 to address data memory – value of FSR1 post-incremented (not a physical register)
N/A
49, 70
POSTDEC1
Uses contents of FSR1 to address data memory – value of FSR1 post-decremented (not a physical register)
N/A
49, 70
PREINC1
Uses contents of FSR1 to address data memory – value of FSR1 pre-incremented (not a physical register)
N/A
49, 70
PLUSW1
Uses contents of FSR1 to address data memory – value of FSR1 pre-incremented (not a physical register) –
value of FSR1 offset by W
N/A
49, 70
---- 0000
50, 70
FSR1H
—
FSR1L
—
—
—
—
—
Indirect Data Memory Address Pointer 0 High
—
Indirect Data Memory Address Pointer 1 High
Indirect Data Memory Address Pointer 1 Low Byte
BSR
—
—
—
—
Bank Select Register
xxxx xxxx
50, 70
---- 0000
50, 59
INDF2
Uses contents of FSR2 to address data memory – value of FSR2 not changed (not a physical register)
N/A
50, 70
POSTINC2
Uses contents of FSR2 to address data memory – value of FSR2 post-incremented (not a physical register)
N/A
50, 70
POSTDEC2
Uses contents of FSR2 to address data memory – value of FSR2 post-decremented (not a physical register)
N/A
50, 70
PREINC2
Uses contents of FSR2 to address data memory – value of FSR2 pre-incremented (not a physical register)
N/A
50, 70
PLUSW2
Uses contents of FSR2 to address data memory – value of FSR2 pre-incremented (not a physical register) –
value of FSR2 offset by W
N/A
50, 70
---- 0000
50, 70
FSR2H
—
FSR2L
—
—
—
Indirect Data Memory Address Pointer 2 High
Indirect Data Memory Address Pointer 2 Low Byte
STATUS
Legend:
Note 1:
2:
3:
4:
5:
6:
—
—
—
N
OV
Z
DC
C
xxxx xxxx
50, 70
---x xxxx
50, 68
x = unknown, u = unchanged, — = unimplemented, q = value depends on condition
The SBOREN bit is only available when the BOREN1:BOREN0 configuration bits = 01; otherwise, it is disabled and reads as ‘0’. See
Section 4.4 “Brown-out Reset (BOR)”.
These registers and/or bits are not implemented on 28-pin devices and are read as ‘0’. Reset values are shown for 40/44-pin devices;
individual unimplemented bits should be interpreted as ‘-’.
The PLLEN bit is only available in specific oscillator configuration; otherwise it is disabled and reads as ‘0’. See Section 2.6.4 “PLL in
INTOSC Modes”.
The RE3 bit is only available when Master Clear Reset is disabled (MCLRE configuration bit = 0). Otherwise, RE3 reads as ‘0’. This bit is
read-only.
RA6/RA7 and their associated latch and direction bits are individually configured as port pins based on various primary oscillator modes.
When disabled, these bits read as ‘0’.
Bit 7 and bit 6 are cleared by user software or by a POR.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 65
PIC18F2X1X/4X1X
TABLE 5-2:
File Name
REGISTER FILE SUMMARY (PIC18F2X1X/4X1X) (CONTINUED)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Value on
POR, BOR
Details
on page:
TMR0H
Timer0 Register High Byte
0000 0000
50, 115
TMR0L
Timer0 Register Low Byte
xxxx xxxx
50, 115
50, 113
T0CON
TMR0ON
T08BIT
T0CS
T0SE
PSA
T0PS2
T0PS1
T0PS0
1111 1111
OSCCON
IDLEN
IRCF2
IRCF1
IRCF0
OSTS
IOFS
SCS1
SCS0
0100 q000
30, 50
HLVDCON
VDIRMAG
—
IRVST
HLVDEN
HLVDL3
HLVDL2
HLVDL1
HLVDL0
0-00 0101
50, 231
WDTCON
—
—
—
—
—
—
—
SWDTEN
--- ---0
50, 247
—
RI
TO
PD
POR
BOR
RCON
IPEN
SBOREN
(1)
0q-1 11q0 42, 48, 92
TMR1H
Timer1 Register High Byte
xxxx xxxx
50, 121
TMR1L
Timer1 Register Low Bytes
xxxx xxxx
50, 121
T1CON
RD16
T1RUN
TMR2
Timer2 Register
PR2
Timer2 Period Register
T2CON
—
T2OUTPS3
T1CKPS1
T2OUTPS2
T1CKPS0
T2OUTPS1
T1OSCEN
T2OUTPS0
T1SYNC
TMR2ON
TMR1CS
T2CKPS1
SSPBUF
SSP Receive Buffer/Transmit Register
SSPADD
SSP Address Register in I2C Slave Mode. SSP Baud Rate Reload Register in I2C Master Mode.
TMR1ON
T2CKPS0
0000 0000
50, 117
0000 0000
50, 124
1111 1111
50, 124
-000 0000
50, 123
xxxx xxxx
50, 159,
160
0000 0000
50, 160
SSPSTAT
SMP
CKE
D/A
P
S
R/W
UA
BF
0000 0000
50, 152,
161
SSPCON1
WCOL
SSPOV
SSPEN
CKP
SSPM3
SSPM2
SSPM1
SSPM0
0000 0000
50, 153,
162
GCEN
ACKSTAT
ACKDT
ACKEN
RCEN
PEN
RSEN
SEN
SSPCON2
0000 0000
50, 163
ADRESH
A/D Result Register High Byte
xxxx xxxx
51, 220
ADRESL
A/D Result Register Low Byte
xxxx xxxx
51, 220
ADCON0
—
—
CHS3
CHS2
CHS1
CHS0
GO/DONE
ADON
--00 0000
51, 211
ADCON1
—
—
VCFG1
VCFG0
PCFG3
PCFG2
PCFG1
PCFG0
--00 0qqq
51, 212
ADFM
—
ACQT2
ACQT1
ACQT0
ADCS2
ADCS1
ADCS0
ADCON2
0-00 0000
51, 213
CCPR1H
Capture/Compare/PWM Register 1 High Byte
xxxx xxxx
51, 130
CCPR1L
Capture/Compare/PWM Register 1 Low Byte
xxxx xxxx
51, 130
0000 0000
51, 129,
137
51, 130
CCP1CON
P1M1(2)
P1M0(2)
DC1B1
DC1B0
CCP1M3
CCP1M2
CCP1M1
CCP1M0
CCPR2H
Capture/Compare/PWM Register 2 High Byte
xxxx xxxx
CCPR2L
Capture/Compare/PWM Register 2 Low Byte
xxxx xxxx
51, 130
--00 0000
51, 129
CCP2CON
—
BAUDCON
ABDOVF
RCIDL
—
SCKP
BRG16
—
WUE
ABDEN
01-0 0-00
51, 194
PWM1CON
PRSEN
PDC6(2)
PDC5(2)
PDC4(2)
PDC3(2)
PDC2(2)
PDC1(2)
PDC0(2)
0000 0000
51, 146
ECCP1AS
ECCPASE
ECCPAS2
ECCPAS1
ECCPAS0
PSSAC1
PSSAC0
PSSBD1(2)
PSSBD0(2) 0000 0000
51, 147
CVRCON
CVREN
CVROE
CVRR
CVRSS
CVR3
CVR2
CVR1
CVR0
0000 0000
51, 227
CMCON
C2OUT
C1OUT
C2INV
C1INV
CIS
CM2
CM1
CM0
0000 0111
51, 221
—
DC2B1
DC2B0
CCP2M3
CCP2M2
CCP2M1
CCP2M0
TMR3H
Timer3 Register High Byte
xxxx xxxx
51, 127
TMR3L
Timer3 Register Low Byte
xxxx xxxx
51, 127
0000 0000
51, 125
T3CON
RD16
Legend:
Note 1:
2:
3:
4:
5:
6:
T3CCP2
T3CKPS1
T3CKPS0
T3CCP1
T3SYNC
TMR3CS
TMR3ON
x = unknown, u = unchanged, — = unimplemented, q = value depends on condition
The SBOREN bit is only available when the BOREN1:BOREN0 configuration bits = 01; otherwise, it is disabled and reads as ‘0’. See
Section 4.4 “Brown-out Reset (BOR)”.
These registers and/or bits are not implemented on 28-pin devices and are read as ‘0’. Reset values are shown for 40/44-pin devices;
individual unimplemented bits should be interpreted as ‘-’.
The PLLEN bit is only available in specific oscillator configuration; otherwise it is disabled and reads as ‘0’. See Section 2.6.4 “PLL in
INTOSC Modes”.
The RE3 bit is only available when Master Clear Reset is disabled (MCLRE configuration bit = 0). Otherwise, RE3 reads as ‘0’. This bit is
read-only.
RA6/RA7 and their associated latch and direction bits are individually configured as port pins based on various primary oscillator modes.
When disabled, these bits read as ‘0’.
Bit 7 and bit 6 are cleared by user software or by a POR.
DS39636A-page 66
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
TABLE 5-2:
File Name
REGISTER FILE SUMMARY (PIC18F2X1X/4X1X) (CONTINUED)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Value on
POR, BOR
Details
on page:
SPBRGH
EUSART Baud Rate Generator Register High Byte
0000 0000
51, 195
SPBRG
EUSART Baud Rate Generator Register Low Byte
0000 0000
51, 195
RCREG
EUSART Receive Register
0000 0000
51, 202
TXREG
EUSART Transmit Register
0000 0000
51, 200
TXSTA
CSRC
TX9
TXEN
SYNC
SENDB
BRGH
TRMT
TX9D
0000 0010
51, 192
RCSTA
SPEN
RX9
SREN
CREN
ADDEN
FERR
OERR
RX9D
0000 000x
51, 193
IPR2
OSCFIP
CMIP
—
—
BCLIP
HLVDIP
TMR3IP
CCP2IP
11-- 1111
52, 91
PIR2
OSCFIF
CMIF
—
—
BCLIF
HLVDIF
TMR3IF
CCP2IF
00-- 0000
52, 87
PIE2
OSCFIE
CMIE
—
—
BCLIE
HLVDIE
TMR3IE
CCP2IE
00-- 0000
52, 89
IPR1
PSPIP(2)
ADIP
RCIP
TXIP
SSPIP
CCP1IP
TMR2IP
TMR1IP
1111 1111
52, 90
52, 86
PIR1
PSPIF(2)
ADIF
RCIF
TXIF
SSPIF
CCP1IF
TMR2IF
TMR1IF
0000 0000
PIE1
PSPIE(2)
ADIE
RCIE
TXIE
SSPIE
CCP1IE
TMR2IE
TMR1IE
0000 0000
52, 88
OSCTUNE
INTSRC
PLLEN(3)
—
TUN4
TUN3
TUN2
TUN1
TUN0
0q-0 0000
27, 52
IBF
OBF
IBOV
PSPMODE
—
TRISE2
TRISE1
TRISE0
TRISE(2)
0000 -111
52, 108
PORTD Data Direction Control Register
1111 1111
52, 104
TRISC
PORTC Data Direction Control Register
1111 1111
52, 101
TRISB
PORTB Data Direction Control Register
1111 1111
52, 98
TRISD(2)
TRISA
TRISA7(5)
TRISA6(5)
LATE(2)
—
—
Data Direction Control Register for PORTA
—
—
—
PORTE Data Latch Register
(Read and Write to Data Latch)
1111 1111
52, 95
---- -xxx
52, 107
LATD(2)
PORTD Data Latch Register (Read and Write to Data Latch)
xxxx xxxx
52, 104
LATC
PORTC Data Latch Register (Read and Write to Data Latch)
xxxx xxxx
52, 101
LATB
PORTB Data Latch Register (Read and Write to Data Latch)
xxxx xxxx
52, 98
LATA
PORTE
LATA7(6)
LATA6(6)
—
—
PORTA Data Latch Register (Read and Write to Data Latch)
—
RE3(4)
—
xxxx xxxx
52, 95
RE2(2)
RE1(2)
RE0(2)
---- xxxx
52, 107
PORTD(2)
RD7
RD6
RD5
RD4
RD3
RD2
RD1
RD0
xxxx xxxx
52, 104
PORTC
RC7
RC6
RC5
RC4
RC3
RC2
RC1
RC0
xxxx xxxx
52, 101
PORTB
RB7
RB6
RB5
RB4
RB3
RB2
RB1
RB0
xxxx xxxx
52, 98
PORTA
RA7(5)
RA6(5)
RA5
RA4
RA3
RA2
RA1
RA0
xx0x 0000
52, 95
Legend:
Note 1:
2:
3:
4:
5:
6:
x = unknown, u = unchanged, — = unimplemented, q = value depends on condition
The SBOREN bit is only available when the BOREN1:BOREN0 configuration bits = 01; otherwise, it is disabled and reads as ‘0’. See
Section 4.4 “Brown-out Reset (BOR)”.
These registers and/or bits are not implemented on 28-pin devices and are read as ‘0’. Reset values are shown for 40/44-pin devices;
individual unimplemented bits should be interpreted as ‘-’.
The PLLEN bit is only available in specific oscillator configuration; otherwise it is disabled and reads as ‘0’. See Section 2.6.4 “PLL in
INTOSC Modes”.
The RE3 bit is only available when Master Clear Reset is disabled (MCLRE configuration bit = 0). Otherwise, RE3 reads as ‘0’. This bit is
read-only.
RA6/RA7 and their associated latch and direction bits are individually configured as port pins based on various primary oscillator modes.
When disabled, these bits read as ‘0’.
Bit 7 and bit 6 are cleared by user software or by a POR.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 67
PIC18F2X1X/4X1X
5.3.5
STATUS REGISTER
The Status register, shown in Register 5-2, contains the
arithmetic status of the ALU. As with any other SFR, it
can be the operand for any instruction.
If the Status register is the destination for an instruction
that affects the Z, DC, C, OV or N bits, the results of the
instruction are not written; instead, the status is
updated according to the instruction performed. Therefore, the result of an instruction with the Status register
as its destination may be different than intended. As an
example, CLRF STATUS will set the Z bit and leave the
remaining status bits unchanged (‘000u u1uu’).
REGISTER 5-2:
It is recommended that only BCF, BSF, SWAPF, MOVFF
and MOVWF instructions are used to alter the Status
register, because these instructions do not affect the Z,
C, DC, OV or N bits in the Status register.
For other instructions that do not affect status bits, see
the instruction set summaries in Table 23-2 and
Table 23-3.
Note:
The C and DC bits operate as the borrow
and digit borrow bits, respectively, in
subtraction.
STATUS REGISTER
U-0
U-0
U-0
R/W-x
R/W-x
R/W-x
R/W-x
R/W-x
—
—
—
N
OV
Z
DC
C
bit 7
bit 0
bit 7-5
Unimplemented: Read as ‘0’
bit 4
N: Negative bit
This bit is used for signed arithmetic (2’s complement). It indicates whether the result was
negative (ALU MSB = 1).
1 = Result was negative
0 = Result was positive
bit 3
OV: Overflow bit
This bit is used for signed arithmetic (2’s complement). It indicates an overflow of the 7-bit
magnitude which causes the sign bit (bit 7 of the result) to change state.
1 = Overflow occurred for signed arithmetic (in this arithmetic operation)
0 = No overflow occurred
bit 2
Z: Zero bit
1 = The result of an arithmetic or logic operation is zero
0 = The result of an arithmetic or logic operation is not zero
bit 1
DC: Digit carry/borrow bit
For ADDWF, ADDLW, SUBLW and SUBWF instructions:
1 = A carry-out from the 4th low-order bit of the result occurred
0 = No carry-out from the 4th low-order bit of the result
Note:
bit 0
For borrow, the polarity is reversed. A subtraction is executed by adding the
2’s complement of the second operand. For rotate (RRF, RLF) instructions, this bit
is loaded with either bit 4 or bit 3 of the source register.
C: Carry/borrow bit
For ADDWF, ADDLW, SUBLW and SUBWF instructions:
1 = A carry-out from the Most Significant bit of the result occurred
0 = No carry-out from the Most Significant bit of the result occurred
Note:
For borrow, the polarity is reversed. A subtraction is executed by adding the
2’s complement of the second operand. For rotate (RRF, RLF) instructions, this bit
is loaded with either the high or low-order bit of the source register.
Legend:
DS39636A-page 68
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
Preliminary
x = Bit is unknown
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
5.4
Data Addressing Modes
Note:
The execution of some instructions in the
core PIC18 instruction set are changed
when the PIC18 extended instruction set is
enabled. See Section 5.5 “Data Memory
and the Extended Instruction Set” for
more information.
The data memory space can be addressed in several
ways. For most instructions, the addressing mode is
fixed. Other instructions may use up to three modes,
depending on which operands are used and whether or
not the extended instruction set is enabled.
The addressing modes are:
•
•
•
•
Inherent
Literal
Direct
Indirect
An additional addressing mode, Indexed Literal Offset,
is available when the extended instruction set is
enabled (XINST configuration bit = 1). Its operation is
discussed in greater detail in Section 5.5.1 “Indexed
Addressing with Literal Offset”.
5.4.1
INHERENT AND LITERAL
ADDRESSING
Many PIC18 control instructions do not need any
argument at all; they either perform an operation that
globally affects the device or they operate implicitly on
one register. This addressing mode is known as
Inherent Addressing. Examples include SLEEP, RESET
and DAW.
Other instructions work in a similar way but require an
additional explicit argument in the opcode. This is
known as Literal Addressing mode because they
require some literal value as an argument. Examples
include ADDLW and MOVLW which, respectively, add or
move a literal value to the W register. Other examples
include CALL and GOTO, which include a 20-bit
program memory address.
5.4.2
DIRECT ADDRESSING
A few instructions, such as MOVFF, include the entire
12-bit address (either source or destination) in their
opcodes. In these cases, the BSR is ignored entirely.
The destination of the operation’s results is determined
by the destination bit ‘d’. When ‘d’ is ‘1’, the results are
stored back in the source register, overwriting its original contents. When ‘d’ is ‘0’, the results are stored in
the W register. Instructions without the ‘d’ argument
have a destination that is implicit in the instruction; their
destination is either the target register being operated
on or the W register.
5.4.3
In the core PIC18 instruction set, bit-oriented and byteoriented instructions use some version of direct
addressing by default. All of these instructions include
some 8-bit literal address as their Least Significant
Byte. This address specifies either a register address in
one of the banks of data RAM (Section 5.3.3 “General
Purpose Register File”) or a location in the Access
Bank (Section 5.3.2 “Access Bank”) as the data
source for the instruction.
INDIRECT ADDRESSING
Indirect addressing allows the user to access a location
in data memory without giving a fixed address in the
instruction. This is done by using File Select Registers
(FSRs) as pointers to the locations to be read or written
to. Since the FSRs are themselves located in RAM as
Special File Registers, they can also be directly manipulated under program control. This makes FSRs very
useful in implementing data structures, such as tables
and arrays in data memory.
The registers for indirect addressing are also
implemented with Indirect File Operands (INDFs) that
permit automatic manipulation of the pointer value with
auto-incrementing, auto-decrementing or offsetting
with another value. This allows for efficient code, using
loops, such as the example of clearing an entire RAM
bank in Example 5-5.
EXAMPLE 5-5:
NEXT
Direct addressing specifies all or part of the source
and/or destination address of the operation within the
opcode itself. The options are specified by the
arguments accompanying the instruction.
 2004 Microchip Technology Inc.
The Access RAM bit ‘a’ determines how the address is
interpreted. When ‘a’ is ‘1’, the contents of the BSR
(Section 5.3.1 “Bank Select Register (BSR)”) are
used with the address to determine the complete 12-bit
address of the register. When ‘a’ is ‘0’, the address is
interpreted as being a register in the Access Bank.
Addressing that uses the Access RAM is sometimes
also known as Direct Forced Addressing mode.
LFSR
CLRF
BTFSS
BRA
CONTINUE
Preliminary
HOW TO CLEAR RAM
(BANK 1) USING
INDIRECT ADDRESSING
FSR0, 100h ;
POSTINC0
; Clear INDF
; register then
; inc pointer
FSR0H, 1
; All done with
; Bank1?
NEXT
; NO, clear next
; YES, continue
DS39636A-page 69
PIC18F2X1X/4X1X
5.4.3.1
FSR Registers and the INDF
Operand
5.4.3.2
At the core of indirect addressing are three sets of
registers: FSR0, FSR1 and FSR2. Each represents a
pair of 8-bit registers, FSRnH and FSRnL. The four
upper bits of the FSRnH register are not used so each
FSR pair holds a 12-bit value. This represents a value
that can address the entire range of the data memory
in a linear fashion. The FSR register pairs, then, serve
as pointers to data memory locations.
In addition to the INDF operand, each FSR register pair
also has four additional indirect operands. Like INDF,
these are “virtual” registers that cannot be indirectly
read or written to. Accessing these registers actually
accesses the associated FSR register pair, but also
performs a specific action on its stored value. They are:
• POSTDEC: accesses the FSR value, then
automatically decrements it by 1 afterwards
• POSTINC: accesses the FSR value, then
automatically increments it by 1 afterwards
• PREINC: increments the FSR value by 1, then
uses it in the operation
• PLUSW: adds the signed value of the W register
(range of -127 to 128) to that of the FSR and uses
the new value in the operation.
Indirect addressing is accomplished with a set of
Indirect File Operands, INDF0 through INDF2. These
can be thought of as “virtual” registers: they are
mapped in the SFR space but are not physically implemented. Reading or writing to a particular INDF register
actually accesses its corresponding FSR register pair.
A read from INDF1, for example, reads the data at the
address indicated by FSR1H:FSR1L. Instructions that
use the INDF registers as operands actually use the
contents of their corresponding FSR as a pointer to the
instruction’s target. The INDF operand is just a
convenient way of using the pointer.
In this context, accessing an INDF register uses the
value in the FSR registers without changing them. Similarly, accessing a PLUSW register gives the FSR value
offset by that in the W register; neither value is actually
changed in the operation. Accessing the other virtual
registers changes the value of the FSR registers.
Because indirect addressing uses a full 12-bit address,
data RAM banking is not necessary. Thus, the current
contents of the BSR and the Access RAM bit have no
effect on determining the target address.
FIGURE 5-9:
FSR Registers and POSTINC,
POSTDEC, PREINC and PLUSW
Operations on the FSRs with POSTDEC, POSTINC
and PREINC affect the entire register pair; that is, rollovers of the FSRnL register from FFh to 00h carry over
to the FSRnH register. On the other hand, results of
these operations do not change the value of any flags
in the Status register (e.g., Z, N, OV, etc.).
INDIRECT ADDRESSING
000h
Using an instruction with one of the
indirect addressing registers as the
operand....
Bank 0
ADDWF, INDF1, 1
100h
Bank 1
200h
Bank 2
...uses the 12-bit address stored in
the FSR pair associated with that
register....
300h
FSR1H:FSR1L
7
0
x x x x 1 1 1 0
7
0
Bank 3
through
Bank 13
1 1 0 0 1 1 0 0
...to determine the data memory
location to be used in that operation.
E00h
In this case, the FSR1 pair contains
ECCh. This means the contents of
location ECCh will be added to that
of the W register and stored back in
ECCh.
Bank 14
F00h
Bank 15
FFFh
Data Memory
DS39636A-page 70
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
The PLUSW register can be used to implement a form
of indexed addressing in the data memory space. By
manipulating the value in the W register, users can
reach addresses that are fixed offsets from pointer
addresses. In some applications, this can be used to
implement some powerful program control structure,
such as software stacks, inside of data memory.
5.4.3.3
Operations by FSRs on FSRs
Indirect addressing operations that target other FSRs
or virtual registers represent special cases. For example, using an FSR to point to one of the virtual registers
will not result in successful operations. As a specific
case, assume that FSR0H:FSR0L contains FE7h, the
address of INDF1. Attempts to read the value of the
INDF1 using INDF0 as an operand will return 00h.
Attempts to write to INDF1 using INDF0 as the operand
will result in a NOP.
On the other hand, using the virtual registers to write to
an FSR pair may not occur as planned. In these cases,
the value will be written to the FSR pair but without any
incrementing or decrementing. Thus, writing to INDF2
or POSTDEC2 will write the same value to the
FSR2H:FSR2L.
Since the FSRs are physical registers mapped in the
SFR space, they can be manipulated through all direct
operations. Users should proceed cautiously when
working on these registers, particularly if their code
uses indirect addressing.
5.5.1
INDEXED ADDRESSING WITH
LITERAL OFFSET
Enabling the PIC18 extended instruction set changes
the behavior of indirect addressing using the FSR2
register pair within access RAM. Under the proper
conditions, instructions that use the Access Bank – that
is, most bit-oriented and byte-oriented instructions –
can invoke a form of indexed addressing using an
offset specified in the instruction. This special addressing mode is known as Indexed Addressing with Literal
Offset, or Indexed Literal Offset mode.
When using the extended instruction set, this
addressing mode requires the following:
• The use of the Access Bank is forced (‘a’ = 0);
and
• The file address argument is less than or equal to
5Fh.
Under these conditions, the file address of the instruction is not interpreted as the lower byte of an address
(used with the BSR in direct addressing), or as an 8-bit
address in the Access Bank. Instead, the value is
interpreted as an offset value to an address pointer,
specified by FSR2. The offset and the contents of
FSR2 are added to obtain the target address of the
operation.
5.5.2
INSTRUCTIONS AFFECTED BY
INDEXED LITERAL OFFSET MODE
Similarly, operations by indirect addressing are generally permitted on all other SFRs. Users should exercise
the appropriate caution that they do not inadvertently
change settings that might affect the operation of the
device.
Any of the core PIC18 instructions that can use direct
addressing are potentially affected by the Indexed Literal
Offset Addressing mode. This includes all byte-oriented
and bit-oriented instructions, or almost one-half of the
standard PIC18 instruction set. Instructions that only use
Inherent or Literal Addressing modes are unaffected.
5.5
Additionally, byte-oriented and bit-oriented instructions
are not affected if they do not use the Access Bank
(Access RAM bit is ‘1’), or include a file address of 60h
or above. Instructions meeting these criteria will
continue to execute as before. A comparison of the
different possible addressing modes when the
extended instruction set is enabled is shown in
Figure 5-10.
Data Memory and the Extended
Instruction Set
Enabling the PIC18 extended instruction set (XINST
configuration bit = 1) significantly changes certain
aspects of data memory and its addressing. Specifically, the use of the Access Bank for many of the core
PIC18 instructions is different; this is due to the
introduction of a new addressing mode for the data
memory space.
What does not change is just as important. The size of
the data memory space is unchanged, as well as its
linear addressing. The SFR map remains the same.
Core PIC18 instructions can still operate in both Direct
and Indirect Addressing mode; inherent and literal
instructions do not change at all. Indirect addressing
with FSR0 and FSR1 also remain unchanged.
 2004 Microchip Technology Inc.
Those who desire to use bit-oriented or byte-oriented
instructions in the Indexed Literal Offset mode should
note the changes to assembler syntax for this mode.
This is described in more detail in Section 23.2.1
“Extended Instruction Syntax”.
Preliminary
DS39636A-page 71
PIC18F2X1X/4X1X
FIGURE 5-10:
COMPARING ADDRESSING OPTIONS FOR BIT-ORIENTED AND
BYTE-ORIENTED INSTRUCTIONS (EXTENDED INSTRUCTION SET ENABLED)
EXAMPLE INSTRUCTION: ADDWF, f, d, a (Opcode: 0010 01da ffff ffff)
When ‘a’ = 0 and f ≥ 60h:
The instruction executes in
Direct Forced mode. ‘f’ is interpreted as a location in the
Access RAM between 060h
and 0FFh. This is the same as
locations 060h to 07Fh
(Bank 0) and F80h to FFFh
(Bank 15) of data memory.
000h
Locations below 60h are not
available in this addressing
mode.
F00h
060h
080h
Bank 0
100h
00h
Bank 1
through
Bank 14
60h
80h
Access RAM
Valid range
for ‘f’
FFh
Bank 15
F80h
SFRs
FFFh
Data Memory
When ‘a’ = 0 and f ≤ 5Fh:
The instruction executes in
Indexed Literal Offset mode. ‘f’
is interpreted as an offset to the
address value in FSR2. The
two are added together to
obtain the address of the target
register for the instruction. The
address can be anywhere in
the data memory space.
Note that in this mode, the
correct syntax is now:
ADDWF [k], d
where ‘k’ is the same as ‘f’.
000h
Bank 0
080h
100h
001001da ffffffff
Bank 1
through
Bank 14
FSR2H
FSR2L
F00h
Bank 15
F80h
SFRs
FFFh
Data Memory
When ‘a’ = 1 (all values of f):
The instruction executes in
Direct mode (also known as
Direct Long mode). ‘f’ is interpreted as a location in one of
the 16 banks of the data
memory space. The bank is
designated by the Bank Select
Register (BSR). The address
can be in any implemented
bank in the data memory
space.
BSR
00000000
000h
Bank 0
080h
100h
Bank 1
through
Bank 14
001001da ffffffff
F00h
Bank 15
F80h
SFRs
FFFh
Data Memory
DS39636A-page 72
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
5.5.3
MAPPING THE ACCESS BANK IN
INDEXED LITERAL OFFSET
ADDRESSING MODE
The use of Indexed Literal Offset Addressing mode
effectively changes how the first 96 locations of access
RAM (00h to 5Fh) are mapped. Rather than containing
just the contents of the bottom half of Bank 0, this mode
maps the contents from Bank 0 and a user defined
“window” that can be located anywhere in the data
memory space. The value of FSR2 establishes the
lower boundary of the addresses mapped into the
window, while the upper boundary is defined by FSR2
plus 95 (5Fh). Addresses in the Access RAM above
5Fh are mapped as previously described (see
Section 5.3.2 “Access Bank”). An example of Access
Bank remapping in this addressing mode is shown in
Figure 5-11.
FIGURE 5-11:
Remapping of the Access Bank applies only to operations using the Indexed Literal Offset Addressing
mode. Operations that use the BSR (Access RAM bit is
‘1’) will continue to use direct addressing as before.
5.6
PIC18 Instruction Execution and
the Extended Instruction Set
Enabling the extended instruction set adds eight
additional commands to the existing PIC18 instruction
set. These instructions are executed as described in
Section 23.2 “Extended Instruction Set”.
REMAPPING THE ACCESS BANK WITH INDEXED LITERAL OFFSET
ADDRESSING
Example Situation:
ADDWF f, d, a
FSR2H:FSR2L = 120h
Locations in the region
from the FSR2 pointer
(120h) to the pointer plus
05Fh (17Fh) are mapped
to the bottom of the
Access RAM (000h-05Fh).
000h
05Fh
07Fh
Bank 0
100h
120h
17Fh
200h
Bank 0 addresses below
5Fh can still be addressed
by using the BSR.
Bank 1
Window
00h
Bank 1
Bank 1 “Window”
5Fh
Locations in Bank 0 from
060h to 07Fh are mapped,
as usual, to the middle of
the Access Bank.
Special File Registers at
F80h through FFFh are
mapped to 80h through
FFh, as usual.
Bank 0
Bank 0
Bank 2
through
Bank 14
7Fh
80h
SFRs
FFh
Access Bank
F00h
Bank 15
F80h
SFRs
FFFh
Data Memory
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 73
PIC18F2X1X/4X1X
NOTES:
DS39636A-page 74
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
6.0
FLASH PROGRAM MEMORY
In PIC18F2X1X/4X1X devices, the program memory is
implemented as read-only Flash memory. It is readable
over the entire VDD range during normal operation. A
read from program memory is executed on one byte at
a time.
6.1
Table Reads
For PIC18 devices, there are two operations that allow
the processor to move bytes between the program
memory space and the data RAM: table read (TBLRD)
and table write (TBLWT).
Table read operations retrieve data from program
memory and place it into the data RAM space.
Figure 6-1 shows the operation of a table read with
program memory and data RAM.
Table reads work with byte entities. A table block
containing data, rather than program instructions, is not
required to be word-aligned. Therefore, a table block can
start and end at any byte address.
Because the program memory cannot be written to or
erased under normal operation, the TBLWT operation is
not discussed here.
Note 1: Although it cannot be used in
PIC18F2X1X/4X1X devices in normal
operation, the TBLWT instruction is still
implemented in the instruction set.
Executing the instruction takes two
instruction cycles, but effectively results
in a NOP.
2: The TBLWT instruction is available only in
programming modes and is used during
In-Circuit Serial Programming™ (ICSP™).
The program memory space is 16 bits wide, while the
data RAM space is 8 bits wide. Table reads and table
writes move data between these two memory spaces
through an 8-bit register, TABLAT.
FIGURE 6-1:
TABLE READ OPERATION
Instruction: TBLRD*
Program Memory
Table Pointer(1)
TBLPTRU
TBLPTRH
Table Latch (8-bit)
TBLPTRL
TABLAT
Program Memory
(TBLPTR)
Note 1: Table Pointer register points to a byte in program memory.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 75
PIC18F2X1X/4X1X
TABLE 6-1:
Two control registers are used in conjunction with the
TBLRD instruction: the TABLAT register and the
TBLPTR register set.
TABLE POINTER
OPERATIONS WITH TBLRD
INSTRUCTIONS
Example
Operation on Table Pointer
6.2.1
TABLAT – TABLE LATCH REGISTER
TBLRD*
The Table Latch (TABLAT) is an 8-bit register mapped
into the SFR space. The Table Latch register is used to
hold 8-bit data during data transfers between program
memory and data RAM.
TBLRD*+
TBLPTR is incremented after the read
TBLRD*-
TBLPTR is decremented after the read
TBLRD+*
TBLPTR is incremented before the read
6.2
6.2.2
Control Registers
6.3
TBLPTR – TABLE POINTER
REGISTER
The Table Pointer register (TBLPTR) addresses a byte
within the program memory. It is comprised of three
SFR registers: Table Pointer Upper Byte, Table Pointer
High Byte and Table Pointer Low Byte
(TBLPTRU:TBLPTRH:TBLPTRL). Only the lower six
bits of TBLPTRU are used with TBLPTRH and
TBLPTRL, to form a 22-bit wide pointer.
The contents of TBLPTR indicate a location in program
memory space. The low-order 21 bits allow the device
to address the full 2 Mbytes of program memory space.
The 22nd bit allows access to the configuration space,
including the device ID, user ID locations and the
configuration bits.
The TBLPTR register set is updated when executing a
TBLRD in one of four ways, based on the instruction’s
arguments. These are detailed in Table 6-1. These
operations on the TBLPTR only affect the low-order
21 bits.
TBLPTR is not modified
Reading the Flash Program
Memory
The TBLRD instruction is used to retrieve data from
program memory and place it into data RAM. Table
reads from program memory are performed one byte at
a time.
TBLPTR points to a byte address in program space.
Executing TBLRD places the byte pointed to into
TABLAT. In addition, TBLPTR can be modified
automatically for the next table read operation.
The internal program memory is typically organized by
words. The Least Significant bit of the address selects
between the high and low bytes of the word. Figure 6-2
shows the interface between the internal program
memory and the TABLAT.
A typical method for reading data from program memory
is shown in Example 6-1.
When a TBLRD is executed, all 22 bits of the TBLPTR
determine which byte is read from program memory
into TABLAT.
FIGURE 6-2:
READS FROM FLASH PROGRAM MEMORY
Program Memory
(Even Byte Address)
(Odd Byte Address)
TBLPTR = xxxxx1
Instruction Register
(IR)
DS39636A-page 76
FETCH
TBLRD
Preliminary
TBLPTR = xxxxx0
TABLAT
Read Register
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
EXAMPLE 6-1:
READING A FLASH PROGRAM MEMORY WORD
MOVLW
MOVWF
MOVLW
MOVWF
MOVLW
MOVWF
CODE_ADDR_UPPER
TBLPTRU
CODE_ADDR_HIGH
TBLPTRH
CODE_ADDR_LOW
TBLPTRL
; Load TBLPTR with the base
; address of the word
READ_WORD
TBLRD*+
MOVF
MOVWF
TBLRD*+
MOVF
MOVF
TABLE 6-2:
Name
TBLPTRU
; read into TABLAT and increment
; get data
TABLAT, W
WORD_EVEN
; read into TABLAT and increment
; get data
TABLAT, W
WORD_ODD
REGISTERS ASSOCIATED WITH READING PROGRAM FLASH MEMORY
Bit 7
Bit 6
Bit 5
—
—
bit 21
Bit 4
Bit 3
Bit 2
Bit 1
Program Memory Table Pointer Upper Byte
(TBLPTR<20:16>)
Bit 0
Reset
Values on
Page
49
TBPLTRH
Program Memory Table Pointer High Byte (TBLPTR<15:8>)
49
TBLPTRL
Program Memory Table Pointer Low Byte (TBLPTR<7:0>)
49
TABLAT
Program Memory Table Latch
49
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used during Flash access.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 77
PIC18F2X1X/4X1X
NOTES:
DS39636A-page 78
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
7.0
8 x 8 HARDWARE MULTIPLIER
7.1
Introduction
EXAMPLE 7-1:
MOVF
MULWF
All PIC18 devices include an 8 x 8 hardware multiplier
as part of the ALU. The multiplier performs an unsigned
operation and yields a 16-bit result that is stored in the
product register pair, PRODH:PRODL. The multiplier’s
operation does not affect any flags in the Status
register.
ARG1, W
ARG2
;
; ARG1 * ARG2 ->
; PRODH:PRODL
EXAMPLE 7-2:
Making multiplication a hardware operation allows it to
be completed in a single instruction cycle. This has the
advantages of higher computational throughput and
reduced code size for multiplication algorithms and
allows the PIC18 devices to be used in many applications previously reserved for digital signal processors.
A comparison of various hardware and software
multiply operations, along with the savings in memory
and execution time, is shown in Table 7-1.
7.2
8 x 8 UNSIGNED
MULTIPLY ROUTINE
8 x 8 SIGNED MULTIPLY
ROUTINE
MOVF
MULWF
ARG1, W
ARG2
BTFSC
SUBWF
ARG2, SB
PRODH, F
MOVF
BTFSC
SUBWF
ARG2, W
ARG1, SB
PRODH, F
;
;
;
;
;
ARG1 * ARG2 ->
PRODH:PRODL
Test Sign Bit
PRODH = PRODH
- ARG1
; Test Sign Bit
; PRODH = PRODH
;
- ARG2
Operation
Example 7-1 shows the instruction sequence for an 8 x 8
unsigned multiplication. Only one instruction is required
when one of the arguments is already loaded in the
WREG register.
Example 7-2 shows the sequence to do an 8 x 8 signed
multiplication. To account for the sign bits of the arguments, each argument’s Most Significant bit (MSb) is
tested and the appropriate subtractions are done.
TABLE 7-1:
PERFORMANCE COMPARISON FOR VARIOUS MULTIPLY OPERATIONS
Routine
8 x 8 unsigned
8 x 8 signed
16 x 16 unsigned
16 x 16 signed
Multiply Method
Without hardware multiply
Program
Memory
(Words)
Cycles
(Max)
@ 40 MHz
@ 10 MHz
@ 4 MHz
13
69
6.9 µs
27.6 µs
69 µs
Time
Hardware multiply
1
1
100 ns
400 ns
1 µs
Without hardware multiply
33
91
9.1 µs
36.4 µs
91 µs
Hardware multiply
6
6
600 ns
2.4 µs
6 µs
Without hardware multiply
21
242
24.2 µs
96.8 µs
242 µs
Hardware multiply
28
28
2.8 µs
11.2 µs
28 µs
Without hardware multiply
52
254
25.4 µs
102.6 µs
254 µs
Hardware multiply
35
40
4.0 µs
16.0 µs
40 µs
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 79
PIC18F2X1X/4X1X
Example 7-3 shows the sequence to do a 16 x 16
unsigned multiplication. Equation 7-1 shows the
algorithm that is used. The 32-bit result is stored in four
registers (RES3:RES0).
EQUATION 7-1:
RES3:RES0
=
=
EXAMPLE 7-3:
16 x 16 UNSIGNED
MULTIPLICATION
ALGORITHM
ARG1H:ARG1L • ARG2H:ARG2L
(ARG1H • ARG2H • 216) +
(ARG1H • ARG2L • 28) +
(ARG1L • ARG2H • 28) +
(ARG1L • ARG2L)
EQUATION 7-2:
RES3:RES0 = ARG1H:ARG1L • ARG2H:ARG2L
= (ARG1H • ARG2H • 216) +
(ARG1H • ARG2L • 28) +
(ARG1L • ARG2H • 28) +
(ARG1L • ARG2L) +
(-1 • ARG2H<7> • ARG1H:ARG1L • 216) +
(-1 • ARG1H<7> • ARG2H:ARG2L • 216)
EXAMPLE 7-4:
16 x 16 UNSIGNED
MULTIPLY ROUTINE
MOVF
MULWF
ARG1L, W
ARG2L
MOVFF
MOVFF
PRODH, RES1
PRODL, RES0
MOVF
MULWF
ARG1H, W
ARG2H
MOVFF
MOVFF
PRODH, RES3
PRODL, RES2
MOVF
MULWF
ARG1L, W
ARG2H
MOVF
ADDWF
MOVF
ADDWFC
CLRF
ADDWFC
PRODL, W
RES1, F
PRODH, W
RES2, F
WREG
RES3, F
MOVF
MULWF
ARG1H, W
ARG2L
MOVF
ADDWF
MOVF
ADDWFC
CLRF
ADDWFC
PRODL, W
RES1, F
PRODH, W
RES2, F
WREG
RES3, F
; ARG1L * ARG2L->
; PRODH:PRODL
;
;
ARG1L * ARG2H->
PRODH:PRODL
Add cross
products
ARG1H * ARG2L->
PRODH:PRODL
Add cross
products
MOVFF
MOVFF
PRODH, RES1
PRODL, RES0
MOVF
MULWF
ARG1H, W
ARG2H
MOVFF
MOVFF
PRODH, RES3
PRODL, RES2
MOVF
MULWF
ARG1L, W
ARG2H
MOVF
ADDWF
MOVF
ADDWFC
CLRF
ADDWFC
PRODL, W
RES1, F
PRODH, W
RES2, F
WREG
RES3, F
MOVF
MULWF
ARG1H, W
ARG2L
MOVF
ADDWF
MOVF
ADDWFC
CLRF
ADDWFC
PRODL, W
RES1, F
PRODH, W
RES2, F
WREG
RES3, F
BTFSS
BRA
MOVF
SUBWF
MOVF
SUBWFB
ARG2H, 7
SIGN_ARG1
ARG1L, W
RES2
ARG1H, W
RES3
; ARG2H:ARG2L neg?
; no, check ARG1
;
;
;
ARG1H, 7
CONT_CODE
ARG2L, W
RES2
ARG2H, W
RES3
; ARG1H:ARG1L neg?
; no, done
;
;
;
; ARG1L * ARG2L ->
; PRODH:PRODL
;
;
; ARG1H * ARG2H ->
; PRODH:PRODL
;
;
;
;
;
;
;
;
;
;
ARG1L * ARG2H ->
PRODH:PRODL
Add cross
products
;
;
;
;
;
;
;
;
;
ARG1H * ARG2L ->
PRODH:PRODL
Add cross
products
;
Example 7-4 shows the sequence to do a 16 x 16
signed multiply. Equation 7-2 shows the algorithm
used. The 32-bit result is stored in four registers
(RES3:RES0). To account for the sign bits of the
arguments, the MSb for each argument pair is tested
and the appropriate subtractions are done.
DS39636A-page 80
ARG1L, W
ARG2L
;
;
;
;
;
;
;
;
;
;
;
MOVF
MULWF
;
;
;
;
;
;
;
;
;
;
16 x 16 SIGNED
MULTIPLY ROUTINE
;
;
; ARG1H * ARG2H->
; PRODH:PRODL
;
;
16 x 16 SIGNED
MULTIPLICATION
ALGORITHM
;
SIGN_ARG1
BTFSS
BRA
MOVF
SUBWF
MOVF
SUBWFB
;
CONT_CODE
:
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
8.0
INTERRUPTS
The PIC18F2X1X/4X1X devices have multiple interrupt
sources and an interrupt priority feature that allows
most interrupt sources to be assigned a high priority
level or a low priority level. The high priority interrupt
vector is at 0008h and the low priority interrupt vector is
at 0018h. High priority interrupt events will interrupt any
low priority interrupts that may be in progress.
There are ten registers which are used to control
interrupt operation. These registers are:
•
•
•
•
•
•
•
RCON
INTCON
INTCON2
INTCON3
PIR1, PIR2
PIE1, PIE2
IPR1, IPR2
It is recommended that the Microchip header files
supplied with MPLAB® IDE be used for the symbolic bit
names in these registers. This allows the assembler/
compiler to automatically take care of the placement of
these bits within the specified register.
In general, interrupt sources have three bits to control
their operation. They are:
When an interrupt is responded to, the global interrupt
enable bit is cleared to disable further interrupts. If the
IPEN bit is cleared, this is the GIE bit. If interrupt priority
levels are used, this will be either the GIEH or GIEL bit.
High priority interrupt sources can interrupt a low
priority interrupt. Low priority interrupts are not
processed while high priority interrupts are in progress.
The return address is pushed onto the stack and the
PC is loaded with the interrupt vector address (0008h
or 0018h). Once in the Interrupt Service Routine, the
source(s) of the interrupt can be determined by polling
the interrupt flag bits. The interrupt flag bits must be
cleared in software before re-enabling interrupts to
avoid recursive interrupts.
The “return from interrupt” instruction, RETFIE, exits
the interrupt routine and sets the GIE bit (GIEH or GIEL
if priority levels are used), which re-enables interrupts.
For external interrupt events, such as the INT pins or
the PORTB input change interrupt, the interrupt latency
will be three to four instruction cycles. The exact
latency is the same for one or two-cycle instructions.
Individual interrupt flag bits are set, regardless of the
status of their corresponding enable bit or the GIE bit.
• Flag bit to indicate that an interrupt event
occurred
• Enable bit that allows program execution to
branch to the interrupt vector address when the
flag bit is set
• Priority bit to select high priority or low priority
The interrupt priority feature is enabled by setting the
IPEN bit (RCON<7>). When interrupt priority is
enabled, there are two bits which enable interrupts
globally. Setting the GIEH bit (INTCON<7>) enables all
interrupts that have the priority bit set (high priority).
Setting the GIEL bit (INTCON<6>) enables all
interrupts that have the priority bit cleared (low priority).
When the interrupt flag, enable bit and appropriate
global interrupt enable bit are set, the interrupt will vector immediately to address 0008h or 0018h, depending
on the priority bit setting. Individual interrupts can be
disabled through their corresponding enable bits.
 2004 Microchip Technology Inc.
When the IPEN bit is cleared (default state), the
interrupt priority feature is disabled and interrupts are
compatible with PICmicro® mid-range devices. In
Compatibility mode, the interrupt priority bits for each
source have no effect. INTCON<6> is the PEIE bit,
which enables/disables all peripheral interrupt sources.
INTCON<7> is the GIE bit, which enables/disables all
interrupt sources. All interrupts branch to address
0008h in Compatibility mode.
Note:
Preliminary
Do not use the MOVFF instruction to modify
any of the interrupt control registers while
any interrupt is enabled. Doing so may
cause erratic microcontroller behavior.
DS39636A-page 81
PIC18F2X1X/4X1X
FIGURE 8-1:
PIC18 INTERRUPT LOGIC
Wake-up if in
Idle or Sleep modes
TMR0IF
TMR0IE
TMR0IP
RBIF
RBIE
RBIP
INT0IF
INT0IE
Interrupt to CPU
Vector to Location
0008h
INT1IF
INT1IE
INT1IP
INT2IF
INT2IE
INT2IP
SSPIF
SSPIE
SSPIP
GIEH/GIE
ADIF
ADIE
ADIP
IPEN
IPEN
RCIF
RCIE
RCIP
GIEL/PEIE
IPEN
Additional Peripheral Interrupts
High Priority Interrupt Generation
Low Priority Interrupt Generation
SSPIF
SSPIE
SSPIP
Interrupt to CPU
Vector to Location
0018h
TMR0IF
TMR0IE
TMR0IP
ADIF
ADIE
ADIP
RBIF
RBIE
RBIP
RCIF
RCIE
RCIP
Additional Peripheral Interrupts
GIEH/GIE
GIEL/PEIE
INT1IF
INT1IE
INT1IP
INT2IF
INT2IE
INT2IP
DS39636A-page 82
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
8.1
INTCON Registers
Note:
The INTCON registers are readable and writable
registers, which contain various enable, priority and
flag bits.
REGISTER 8-1:
Interrupt flag bits are set when an interrupt
condition occurs regardless of the state of
its corresponding enable bit or the global
interrupt enable bit. User software should
ensure the appropriate interrupt flag bits
are clear prior to enabling an interrupt.
This feature allows for software polling.
INTCON REGISTER
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-x
GIE/GIEH
PEIE/GIEL
TMR0IE
INT0IE
RBIE
TMR0IF
INT0IF
RBIF
bit 7
bit 0
bit 7
GIE/GIEH: Global Interrupt Enable bit
When IPEN = 0:
1 = Enables all unmasked interrupts
0 = Disables all interrupts
When IPEN = 1:
1 = Enables all high priority interrupts
0 = Disables all interrupts
bit 6
PEIE/GIEL: Peripheral Interrupt Enable bit
When IPEN = 0:
1 = Enables all unmasked peripheral interrupts
0 = Disables all peripheral interrupts
When IPEN = 1:
1 = Enables all low priority peripheral interrupts
0 = Disables all low priority peripheral interrupts
bit 5
TMR0IE: TMR0 Overflow Interrupt Enable bit
1 = Enables the TMR0 overflow interrupt
0 = Disables the TMR0 overflow interrupt
bit 4
INT0IE: INT0 External Interrupt Enable bit
1 = Enables the INT0 external interrupt
0 = Disables the INT0 external interrupt
bit 3
RBIE: RB Port Change Interrupt Enable bit
1 = Enables the RB port change interrupt
0 = Disables the RB port change interrupt
bit 2
TMR0IF: TMR0 Overflow Interrupt Flag bit
1 = TMR0 register has overflowed (must be cleared in software)
0 = TMR0 register did not overflow
bit 1
INT0IF: INT0 External Interrupt Flag bit
1 = The INT0 external interrupt occurred (must be cleared in software)
0 = The INT0 external interrupt did not occur
bit 0
RBIF: RB Port Change Interrupt Flag bit
1 = At least one of the RB7:RB4 pins changed state (must be cleared in software)
0 = None of the RB7:RB4 pins have changed state
Note:
A mismatch condition will continue to set this bit. Reading PORTB will end the
mismatch condition and allow the bit to be cleared.
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
 2004 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS39636A-page 83
PIC18F2X1X/4X1X
REGISTER 8-2:
INTCON2 REGISTER
R/W-1
R/W-1
R/W-1
R/W-1
U-0
R/W-1
U-0
R/W-1
RBPU
INTEDG0
INTEDG1
INTEDG2
—
TMR0IP
—
RBIP
bit 7
bit 0
bit 7
RBPU: PORTB Pull-up Enable bit
1 = All PORTB pull-ups are disabled
0 = PORTB pull-ups are enabled by individual port latch values
bit 6
INTEDG0: External Interrupt 0 Edge Select bit
1 = Interrupt on rising edge
0 = Interrupt on falling edge
bit 5
INTEDG1: External Interrupt 1 Edge Select bit
1 = Interrupt on rising edge
0 = Interrupt on falling edge
bit 4
INTEDG2: External Interrupt 2 Edge Select bit
1 = Interrupt on rising edge
0 = Interrupt on falling edge
bit 3
Unimplemented: Read as ‘0’
bit 2
TMR0IP: TMR0 Overflow Interrupt Priority bit
1 = High priority
0 = Low priority
bit 1
Unimplemented: Read as ‘0’
bit 0
RBIP: RB Port Change Interrupt Priority bit
1 = High priority
0 = Low priority
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
Note:
DS39636A-page 84
x = Bit is unknown
Interrupt flag bits are set when an interrupt condition occurs regardless of the state
of its corresponding enable bit or the global interrupt enable bit. User software
should ensure the appropriate interrupt flag bits are clear prior to enabling an
interrupt. This feature allows for software polling.
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
REGISTER 8-3:
INTCON3 REGISTER
R/W-1
R/W-1
U-0
R/W-0
R/W-0
U-0
R/W-0
R/W-0
INT2IP
INT1IP
—
INT2IE
INT1IE
—
INT2IF
INT1IF
bit 7
bit 0
bit 7
INT2IP: INT2 External Interrupt Priority bit
1 = High priority
0 = Low priority
bit 6
INT1IP: INT1 External Interrupt Priority bit
1 = High priority
0 = Low priority
bit 5
Unimplemented: Read as ‘0’
bit 4
INT2IE: INT2 External Interrupt Enable bit
1 = Enables the INT2 external interrupt
0 = Disables the INT2 external interrupt
bit 3
INT1IE: INT1 External Interrupt Enable bit
1 = Enables the INT1 external interrupt
0 = Disables the INT1 external interrupt
bit 2
Unimplemented: Read as ‘0’
bit 1
INT2IF: INT2 External Interrupt Flag bit
1 = The INT2 external interrupt occurred (must be cleared in software)
0 = The INT2 external interrupt did not occur
bit 0
INT1IF: INT1 External Interrupt Flag bit
1 = The INT1 external interrupt occurred (must be cleared in software)
0 = The INT1 external interrupt did not occur
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
Note:
 2004 Microchip Technology Inc.
x = Bit is unknown
Interrupt flag bits are set when an interrupt condition occurs, regardless of the state
of its corresponding enable bit or the global interrupt enable bit. User software
should ensure the appropriate interrupt flag bits are clear prior to enabling an
interrupt. This feature allows for software polling.
Preliminary
DS39636A-page 85
PIC18F2X1X/4X1X
8.2
PIR Registers
Note 1: Interrupt flag bits are set when an interrupt
condition occurs regardless of the state of
its corresponding enable bit or the Global
Interrupt Enable bit, GIE (INTCON<7>).
The PIR registers contain the individual flag bits for the
peripheral interrupts. Due to the number of peripheral
interrupt sources, there are two Peripheral Interrupt
Request (Flag) registers (PIR1 and PIR2).
REGISTER 8-4:
2: User software should ensure the appropriate interrupt flag bits are cleared prior to
enabling an interrupt and after servicing
that interrupt.
PIR1: PERIPHERAL INTERRUPT REQUEST (FLAG) REGISTER 1
R/W-0
R/W-0
R-0
R-0
R/W-0
R/W-0
R/W-0
R/W-0
PSPIF(1)
ADIF
RCIF
TXIF
SSPIF
CCP1IF
TMR2IF
TMR1IF
bit 7
bit 7
bit 0
PSPIF: Parallel Slave Port Read/Write Interrupt Flag bit(1)
1 = A read or a write operation has taken place (must be cleared in software)
0 = No read or write has occurred
Note 1: This bit is unimplemented on 28-pin devices and is read as ‘0’.
bit 6
ADIF: A/D Converter Interrupt Flag bit
1 = An A/D conversion completed (must be cleared in software)
0 = The A/D conversion is not complete
bit 5
RCIF: EUSART Receive Interrupt Flag bit
1 = The EUSART receive buffer, RCREG, is full (cleared when RCREG is read)
0 = The EUSART receive buffer is empty
bit 4
TXIF: EUSART Transmit Interrupt Flag bit
1 = The EUSART transmit buffer, TXREG, is empty (cleared when TXREG is written)
0 = The EUSART transmit buffer is full
bit 3
SSPIF: Master Synchronous Serial Port Interrupt Flag bit
1 = The transmission/reception is complete (must be cleared in software)
0 = Waiting to transmit/receive
bit 2
CCP1IF: CCP1 Interrupt Flag bit
Capture mode:
1 = A TMR1 register capture occurred (must be cleared in software)
0 = No TMR1 register capture occurred
Compare mode:
1 = A TMR1 register compare match occurred (must be cleared in software)
0 = No TMR1 register compare match occurred
PWM mode:
Unused in this mode.
bit 1
TMR2IF: TMR2 to PR2 Match Interrupt Flag bit
1 = TMR2 to PR2 match occurred (must be cleared in software)
0 = No TMR2 to PR2 match occurred
bit 0
TMR1IF: TMR1 Overflow Interrupt Flag bit
1 = TMR1 register overflowed (must be cleared in software)
0 = TMR1 register did not overflow
Legend:
DS39636A-page 86
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
Preliminary
x = Bit is unknown
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
REGISTER 8-5:
PIR2: PERIPHERAL INTERRUPT REQUEST (FLAG) REGISTER 2
R/W-0
R/W-0
U-0
U-0
R/W-0
R/W-0
R/W-0
R/W-0
OSCFIF
CMIF
—
—
BCLIF
HLVDIF
TMR3IF
CCP2IF
bit 7
bit 0
bit 7
OSCFIF: Oscillator Fail Interrupt Flag bit
1 = Device oscillator failed, clock input has changed to INTOSC (must be cleared in software)
0 = Device clock operating
bit 6
CMIF: Comparator Interrupt Flag bit
1 = Comparator input has changed (must be cleared in software)
0 = Comparator input has not changed
bit 5-4
Unimplemented: Read as ‘0’
bit 3
BCLIF: Bus Collision Interrupt Flag bit
1 = A bus collision occurred (must be cleared in software)
0 = No bus collision occurred
bit 2
HLVDIF: High/Low-Voltage Detect Interrupt Flag bit
1 = A low-voltage condition occurred (must be cleared in software)
0 = The device voltage is above the High/Low-Voltage Detect trip point
bit 1
TMR3IF: TMR3 Overflow Interrupt Flag bit
1 = TMR3 register overflowed (must be cleared in software)
0 = TMR3 register did not overflow
bit 0
CCP2IF: CCPx Interrupt Flag bit
Capture mode:
1 = A TMR1 register capture occurred (must be cleared in software)
0 = No TMR1 register capture occurred
Compare mode:
1 = A TMR1 register compare match occurred (must be cleared in software)
0 = No TMR1 register compare match occurred
PWM mode:
Unused in this mode.
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
 2004 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS39636A-page 87
PIC18F2X1X/4X1X
8.3
PIE Registers
The PIE registers contain the individual enable bits for
the peripheral interrupts. Due to the number of peripheral interrupt sources, there are two Peripheral Interrupt
Enable registers (PIE1 and PIE2). When IPEN = 0, the
PEIE bit must be set to enable any of these peripheral
interrupts.
REGISTER 8-6:
PIE1: PERIPHERAL INTERRUPT ENABLE REGISTER 1
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
PSPIE(1)
ADIE
RCIE
TXIE
SSPIE
CCP1IE
TMR2IE
TMR1IE
bit 7
bit 7
bit 0
PSPIE: Parallel Slave Port Read/Write Interrupt Enable bit(1)
1 = Enables the PSP read/write interrupt
0 = Disables the PSP read/write interrupt
Note 1: This bit is unimplemented on 28-pin devices and is read as ‘0’.
bit 6
ADIE: A/D Converter Interrupt Enable bit
1 = Enables the A/D interrupt
0 = Disables the A/D interrupt
bit 5
RCIE: EUSART Receive Interrupt Enable bit
1 = Enables the EUSART receive interrupt
0 = Disables the EUSART receive interrupt
bit 4
TXIE: EUSART Transmit Interrupt Enable bit
1 = Enables the EUSART transmit interrupt
0 = Disables the EUSART transmit interrupt
bit 3
SSPIE: Master Synchronous Serial Port Interrupt Enable bit
1 = Enables the MSSP interrupt
0 = Disables the MSSP interrupt
bit 2
CCP1IE: CCP1 Interrupt Enable bit
1 = Enables the CCP1 interrupt
0 = Disables the CCP1 interrupt
bit 1
TMR2IE: TMR2 to PR2 Match Interrupt Enable bit
1 = Enables the TMR2 to PR2 match interrupt
0 = Disables the TMR2 to PR2 match interrupt
bit 0
TMR1IE: TMR1 Overflow Interrupt Enable bit
1 = Enables the TMR1 overflow interrupt
0 = Disables the TMR1 overflow interrupt
Legend:
DS39636A-page 88
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
Preliminary
x = Bit is unknown
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
REGISTER 8-7:
PIE2: PERIPHERAL INTERRUPT ENABLE REGISTER 2
R/W-0
R/W-0
U-0
U-0
R/W-0
R/W-0
R/W-0
R/W-0
OSCFIE
CMIE
—
—
BCLIE
HLVDIE
TMR3IE
CCP2IE
bit 7
bit 0
bit 7
OSCFIE: Oscillator Fail Interrupt Enable bit
1 = Enabled
0 = Disabled
bit 6
CMIE: Comparator Interrupt Enable bit
1 = Enabled
0 = Disabled
bit 5-4
Unimplemented: Read as ‘0’
bit 3
BCLIE: Bus Collision Interrupt Enable bit
1 = Enabled
0 = Disabled
bit 2
HLVDIE: High/Low-Voltage Detect Interrupt Enable bit
1 = Enabled
0 = Disabled
bit 1
TMR3IE: TMR3 Overflow Interrupt Enable bit
1 = Enabled
0 = Disabled
bit 0
CCP2IE: CCP2 Interrupt Enable bit
1 = Enabled
0 = Disabled
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
 2004 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS39636A-page 89
PIC18F2X1X/4X1X
8.4
IPR Registers
The IPR registers contain the individual priority bits for
the peripheral interrupts. Due to the number of peripheral interrupt sources, there are two Peripheral Interrupt
Priority registers (IPR1 and IPR2). Using the priority bits
requires that the Interrupt Priority Enable (IPEN) bit be
set.
REGISTER 8-8:
IPR1: PERIPHERAL INTERRUPT PRIORITY REGISTER 1
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
PSPIP(1)
ADIP
RCIP
TXIP
SSPIP
CCP1IP
TMR2IP
TMR1IP
bit 7
bit 7
bit 0
PSPIP: Parallel Slave Port Read/Write Interrupt Priority bit(1)
1 = High priority
0 = Low priority
Note 1: This bit is unimplemented on 28-pin devices and is read as ‘0’.
bit 6
ADIP: A/D Converter Interrupt Priority bit
1 = High priority
0 = Low priority
bit 5
RCIP: EUSART Receive Interrupt Priority bit
1 = High priority
0 = Low priority
bit 4
TXIP: EUSART Transmit Interrupt Priority bit
1 = High priority
0 = Low priority
bit 3
SSPIP: Master Synchronous Serial Port Interrupt Priority bit
1 = High priority
0 = Low priority
bit 2
CCP1IP: CCP1 Interrupt Priority bit
1 = High priority
0 = Low priority
bit 1
TMR2IP: TMR2 to PR2 Match Interrupt Priority bit
1 = High priority
0 = Low priority
bit 0
TMR1IP: TMR1 Overflow Interrupt Priority bit
1 = High priority
0 = Low priority
Legend:
DS39636A-page 90
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
Preliminary
x = Bit is unknown
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
REGISTER 8-9:
IPR2: PERIPHERAL INTERRUPT PRIORITY REGISTER 2
R/W-1
R/W-1
U-0
U-0
R/W-1
R/W-1
R/W-1
R/W-1
OSCFIP
CMIP
—
—
BCLIP
HLVDIP
TMR3IP
CCP2IP
bit 7
bit 0
bit 7
OSCFIP: Oscillator Fail Interrupt Priority bit
1 = High priority
0 = Low priority
bit 6
CMIP: Comparator Interrupt Priority bit
1 = High priority
0 = Low priority
bit 5-4
Unimplemented: Read as ‘0’
bit 3
BCLIP: Bus Collision Interrupt Priority bit
1 = High priority
0 = Low priority
bit 2
HLVDIP: High/Low-Voltage Detect Interrupt Priority bit
1 = High priority
0 = Low priority
bit 1
TMR3IP: TMR3 Overflow Interrupt Priority bit
1 = High priority
0 = Low priority
bit 0
CCP2IP: CCP2 Interrupt Priority bit
1 = High priority
0 = Low priority
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
 2004 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS39636A-page 91
PIC18F2X1X/4X1X
8.5
RCON Register
The RCON register contains flag bits which are used to
determine the cause of the last Reset or wake-up from
Idle or Sleep modes. RCON also contains the IPEN bit
which enables interrupt priorities.
REGISTER 8-10:
The operation of the SBOREN bit and the Reset flag
bits is discussed in more detail in Section 4.1 “RCON
Register”.
RCON REGISTER
R/W-0
R/W-1(1)
U-0
R/W-1
R-1
R-1
R/W-0(1)
R/W-0
IPEN
SBOREN
—
RI
TO
PD
POR
BOR
bit 7
bit 0
bit 7
IPEN: Interrupt Priority Enable bit
1 = Enable priority levels on interrupts
0 = Disable priority levels on interrupts (PIC16XXX Compatibility mode)
bit 6
SBOREN: Software BOR Enable bit(1)
For details of bit operation, see Register 4-1.
Note 1: Actual Reset values are determined by device configuration and the nature of the
device Reset. See Register 4-1 for additional information.
bit 5
Unimplemented: Read as ‘0’
bit 4
RI: RESET Instruction Flag bit
For details of bit operation, see Register 4-1.
bit 3
TO: Watchdog Time-out Flag bit
For details of bit operation, see Register 4-1.
bit 2
PD: Power-down Detection Flag bit
For details of bit operation, see Register 4-1.
bit 1
POR: Power-on Reset Status bit
For details of bit operation, see Register 4-1.
bit 0
BOR: Brown-out Reset Status bit
For details of bit operation, see Register 4-1.
Legend:
DS39636A-page 92
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
Preliminary
x = Bit is unknown
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
8.6
INTn Pin Interrupts
8.7
External interrupts on the RB0/INT0, RB1/INT1 and
RB2/INT2 pins are edge-triggered. If the corresponding
INTEDGx bit in the INTCON2 register is set (= 1), the
interrupt is triggered by a rising edge; if the bit is clear,
the trigger is on the falling edge. When a valid edge
appears on the RBx/INTx pin, the corresponding flag
bit INTxF is set. This interrupt can be disabled by clearing the corresponding enable bit INTxE. Flag bit INTxF
must be cleared in software in the Interrupt Service
Routine before re-enabling the interrupt.
All external interrupts (INT0, INT1 and INT2) can wakeup the processor from Idle or Sleep modes if bit INTxE
was set prior to going into those modes. If the Global
Interrupt Enable bit, GIE, is set, the processor will
branch to the interrupt vector following wake-up.
Interrupt priority for INT1 and INT2 is determined by the
value contained in the interrupt priority bits, INT1IP
(INTCON3<6>) and INT2IP (INTCON3<7>). There is
no priority bit associated with INT0. It is always a high
priority interrupt source.
TMR0 Interrupt
In 8-bit mode (which is the default), an overflow in the
TMR0 register (FFh → 00h) will set flag bit TMR0IF. In
16-bit mode, an overflow in the TMR0H:TMR0L register pair (FFFFh → 0000h) will set TMR0IF. The interrupt
can be enabled/disabled by setting/clearing enable bit,
TMR0IE (INTCON<5>). Interrupt priority for Timer0 is
determined by the value contained in the interrupt
priority bit, TMR0IP (INTCON2<2>). See Section 10.0
“Timer0 Module” for further details on the Timer0
module.
8.8
PORTB Interrupt-on-Change
An input change on PORTB<7:4> sets flag bit, RBIF
(INTCON<0>). The interrupt can be enabled/disabled
by setting/clearing enable bit, RBIE (INTCON<3>).
Interrupt priority for PORTB interrupt-on-change is
determined by the value contained in the interrupt
priority bit, RBIP (INTCON2<0>).
8.9
Context Saving During Interrupts
During interrupts, the return PC address is saved on
the stack. Additionally, the WREG, Status and BSR
registers are saved on the fast return stack. If a fast
return from interrupt is not used (see Section 5.3
“Data Memory Organization”), the user may need to
save the WREG, Status and BSR registers on entry to
the Interrupt Service Routine. Depending on the user’s
application, other registers may also need to be saved.
Example 8-1 saves and restores the WREG, Status
and BSR registers during an Interrupt Service Routine.
EXAMPLE 8-1:
SAVING STATUS, WREG AND BSR REGISTERS IN RAM
MOVWF
W_TEMP
MOVFF
STATUS, STATUS_TEMP
MOVFF
BSR, BSR_TEMP
;
; USER ISR CODE
;
MOVFF
BSR_TEMP, BSR
MOVF
W_TEMP, W
MOVFF
STATUS_TEMP, STATUS
 2004 Microchip Technology Inc.
; W_TEMP is in virtual bank
; STATUS_TEMP located anywhere
; BSR_TMEP located anywhere
; Restore BSR
; Restore WREG
; Restore STATUS
Preliminary
DS39636A-page 93
PIC18F2X1X/4X1X
NOTES:
DS39636A-page 94
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
9.0
I/O PORTS
Reading the PORTA register reads the status of the
pins, whereas writing to it will write to the port latch.
Depending on the device selected and features
enabled, there are up to five ports available. Some pins
of the I/O ports are multiplexed with an alternate
function from the peripheral features on the device. In
general, when a peripheral is enabled, that pin may not
be used as a general purpose I/O pin.
Each port has three registers for its operation. These
registers are:
• TRIS register (data direction register)
• PORT register (reads the levels on the pins of the
device)
• LAT register (output latch)
The Data Latch (LAT register) is useful for read-modifywrite operations on the value that the I/O pins are
driving.
A simplified model of a generic I/O port, without the
interfaces to other peripherals, is shown in Figure 9-1.
FIGURE 9-1:
The Data Latch (LATA) register is also memory mapped.
Read-modify-write operations on the LATA register read
and write the latched output value for PORTA.
The RA4 pin is multiplexed with the Timer0 module
clock input and one of the comparator outputs to
become the RA4/T0CKI/C1OUT pin. Pins RA6 and
RA7 are multiplexed with the main oscillator pins; they
are enabled as oscillator or I/O pins by the selection of
the main oscillator in the configuration register (see
Section 22.1 “Configuration Bits” for details). When
they are not used as port pins, RA6 and RA7 and their
associated TRIS and LAT bits are read as ‘0’.
The other PORTA pins are multiplexed with analog
inputs, the analog VREF+ and VREF- inputs and the comparator voltage reference output. The operation of pins
RA3:RA0 and RA5 as A/D converter inputs is selected
by clearing or setting the control bits in the ADCON1
register (A/D Control Register 1).
Pins RA0 through RA5 may also be used as comparator
inputs or outputs by setting the appropriate bits in the
CMCON register. To use RA3:RA0 as digital inputs, it is
also necessary to turn off the comparators.
GENERIC I/O PORT
OPERATION
RD LAT
Note:
Data
Bus
D
WR LAT
or Port
Q
I/O pin(1)
CK
Data Latch
D
WR TRIS
Q
The RA4/T0CKI/C1OUT pin is a Schmitt Trigger input.
All other PORTA pins have TTL input levels and full
CMOS output drivers.
The TRISA register controls the direction of the PORTA
pins, even when they are being used as analog inputs.
The user must ensure the bits in the TRISA register are
maintained set when using them as analog inputs.
CK
TRIS Latch
Input
Buffer
EXAMPLE 9-1:
RD TRIS
CLRF
Q
D
CLRF
ENEN
RD Port
Note 1:
9.1
On a Power-on Reset, RA5 and RA3:RA0
are configured as analog inputs and read
as ‘0’. RA4 is configured as a digital input.
MOVLW
MOVWF
MOVWF
MOVWF
MOVLW
I/O pins have diode protection to VDD and VSS.
PORTA, TRISA and LATA Registers
PORTA is a 8-bit wide, bidirectional port. The corresponding data direction register is TRISA. Setting a
TRISA bit (= 1) will make the corresponding PORTA pin
an input (i.e., put the corresponding output driver in a
high-impedance mode). Clearing a TRISA bit (= 0) will
make the corresponding PORTA pin an output (i.e., put
the contents of the output latch on the selected pin).
 2004 Microchip Technology Inc.
MOVWF
Preliminary
PORTA
;
;
;
LATA
;
;
;
07h
;
ADCON1 ;
07h
;
CMCON
;
0CFh
;
;
;
TRISA
;
;
INITIALIZING PORTA
Initialize PORTA by
clearing output
data latches
Alternate method
to clear output
data latches
Configure A/D
for digital inputs
Configure comparators
for digital input
Value used to
initialize data
direction
Set RA<3:0> as inputs
RA<5:4> as outputs
DS39636A-page 95
PIC18F2X1X/4X1X
TABLE 9-1:
PORTA I/O SUMMARY
Pin
RA0/AN0
RA1/AN1
RA2/AN2/
VREF-/CVREF
RA3/AN3/VREF+
Function
TRIS
Setting
I/O
I/O
Type
RA0
0
O
DIG
1
I
TTL
PORTA<0> data input; disabled when analog input enabled.
AN0
1
I
ANA
A/D input channel 0 and Comparator C1- input. Default input
configuration on POR; does not affect digital output.
RA1
0
O
DIG
LATA<1> data output; not affected by analog input.
1
I
TTL
PORTA<1> data input; disabled when analog input enabled.
AN1
1
I
ANA
A/D input channel 1 and comparator C2- input. Default input
configuration on POR; does not affect digital output.
RA2
0
O
DIG
LATA<2> data output; not affected by analog input. Disabled when
CVREF output enabled.
1
I
TTL
PORTA<2> data input. Disabled when analog functions enabled;
disabled when CVREF output enabled.
AN2
1
I
ANA
A/D input channel 2 and comparator C2+ input. Default input
configuration on POR; not affected by analog output.
VREF-
1
I
ANA
A/D and comparator voltage reference low input.
CVREF
x
O
ANA
Comparator voltage reference output. Enabling this feature disables
digital I/O.
RA3
0
O
DIG
LATA<3> data output; not affected by analog input.
1
I
TTL
PORTA<3> data input; disabled when analog input enabled.
1
I
ANA
A/D input channel 3 and comparator C1+ input. Default input
configuration on POR.
A/D and comparator voltage reference high input.
AN3
RA4/T0CKI/C1OUT
RA5/AN4/SS/
HLVDIN/C2OUT
OSC2/CLKO/RA6
OSC1/CLKI/RA7
Legend:
Description
LATA<0> data output; not affected by analog input.
VREF+
1
I
ANA
RA4
0
O
DIG
LATA<4> data output.
1
I
ST
PORTA<4> data input; default configuration on POR.
T0CKI
1
I
ST
Timer0 clock input.
C1OUT
0
O
DIG
Comparator 1 output; takes priority over port data.
RA5
0
O
DIG
LATA<5> data output; not affected by analog input.
1
I
TTL
PORTA<5> data input; disabled when analog input enabled.
A/D input channel 4. Default configuration on POR.
AN4
1
I
ANA
SS
1
I
TTL
Slave select input for SSP (MSSP module).
HLVDIN
1
I
ANA
High/Low-Voltage Detect external trip point input.
C2OUT
0
O
DIG
Comparator 2 output; takes priority over port data.
RA6
0
O
DIG
LATA<6> data output. Enabled in RCIO, INTIO2 and ECIO modes only.
1
I
TTL
PORTA<6> data input. Enabled in RCIO, INTIO2 and ECIO modes only.
OSC2
x
O
ANA
Main oscillator feedback output connection (XT, HS and LP modes).
CLKO
x
O
DIG
System cycle clock output (FOSC/4) in RC, INTIO1 and EC Oscillator
modes.
RA7
0
O
DIG
LATA<7> data output. Disabled in external oscillator modes.
1
I
TTL
PORTA<7> data input. Disabled in external oscillator modes.
OSC1
x
I
ANA
Main oscillator input connection.
CLKI
x
I
ANA
Main clock input connection.
DIG = Digital level output; TTL = TTL input buffer; ST = Schmitt Trigger input buffer; ANA = Analog level input/output;
x = Don’t care (TRIS bit does not affect port direction or is overridden for this option).
DS39636A-page 96
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
TABLE 9-2:
Name
PORTA
SUMMARY OF REGISTERS ASSOCIATED WITH PORTA
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
RA7(1)
RA6(1)
RA5
RA4
RA3
RA2
RA1
RA0
(1)
LATA6(1) PORTA Data Latch Register (Read and Write to Data Latch)
LATA
LATA7
TRISA
TRISA7(1) TRISA6(1) PORTA Data Direction Control Register
Reset
Values
on page
52
52
52
ADCON1
—
—
VCFG1
VCFG0
PCFG3
PCFG2
PCFG1
PCFG0
51
CMCON
C2OUT
C1OUT
C2INV
C1INV
CIS
CM2
CM1
CM0
51
CVRCON
CVREN
CVROE
CVRR
CVRSS
CVR3
CVR2
CVR1
CVR0
51
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used by PORTA.
Note 1: RA7:RA6 and their associated latch and data direction bits are enabled as I/O pins based on oscillator
configuration; otherwise, they are read as ‘0’.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 97
PIC18F2X1X/4X1X
9.2
PORTB, TRISB and LATB
Registers
PORTB is an 8-bit wide, bidirectional port. The
corresponding data direction register is TRISB. Setting
a TRISB bit (= 1) will make the corresponding PORTB
pin an input (i.e., put the corresponding output driver in
a high-impedance mode). Clearing a TRISB bit (= 0)
will make the corresponding PORTB pin an output (i.e.,
put the contents of the output latch on the selected pin).
The Data Latch register (LATB) is also memory
mapped. Read-modify-write operations on the LATB
register read and write the latched output value for
PORTB.
EXAMPLE 9-2:
CLRF
CLRF
MOVLW
MOVWF
MOVLW
MOVWF
PORTB
;
;
;
LATB
;
;
;
0Fh
;
ADCON1 ;
;
;
0CFh
;
;
;
TRISB
;
;
;
INITIALIZING PORTB
Four of the PORTB pins (RB7:RB4) have an interrupton-change feature. Only pins configured as inputs can
cause this interrupt to occur (i.e., any RB7:RB4 pin
configured as an output is excluded from the interrupton-change comparison). The input pins (of RB7:RB4)
are compared with the old value latched on the last
read of PORTB. The “mismatch” outputs of RB7:RB4
are ORed together to generate the RB Port Change
Interrupt with Flag bit, RBIF (INTCON<0>).
This interrupt can wake the device from the Sleep
mode, or any of the Idle modes. The user, in the
Interrupt Service Routine, can clear the interrupt in the
following manner:
a)
b)
Initialize PORTB by
clearing output
data latches
Alternate method
to clear output
data latches
Set RB<4:0> as
digital I/O pins
(required if config bit
PBADEN is set)
Value used to
initialize data
direction
Set RB<3:0> as inputs
RB<5:4> as outputs
RB<7:6> as inputs
Any read or write of PORTB (except with the
MOVFF (ANY), PORTB instruction).
Clear flag bit RBIF.
A mismatch condition will continue to set flag bit RBIF.
Reading PORTB will end the mismatch condition and
allow flag bit RBIF to be cleared.
The interrupt-on-change feature is recommended for
wake-up on key depression operation and operations
where PORTB is only used for the interrupt-on-change
feature. Polling of PORTB is not recommended while
using the interrupt-on-change feature.
RB3 can be configured by the configuration bit
CCP2MX as the alternate peripheral pin for the CCP2
module (CCP2MX = 0).
Each of the PORTB pins has a weak internal pull-up. A
single control bit can turn on all the pull-ups. This is
performed by clearing bit, RBPU (INTCON2<7>). The
weak pull-up is automatically turned off when the port
pin is configured as an output. The pull-ups are
disabled on a Power-on Reset.
Note:
On a Power-on Reset, RB4:RB0 are
configured as analog inputs by default and
read as ‘0’; RB7:RB5 are configured as
digital inputs.
By programming the configuration bit,
PBADEN, RB4:RB0 will alternatively be
configured as digital inputs on POR.
DS39636A-page 98
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
TABLE 9-3:
Pin
RB0/INT0/FLT0/
AN12
RB1/INT1/AN10
RB2/INT2/AN8
RB3/AN9/CCP2
PORTB I/O SUMMARY
Function
TRIS
Setting
I/O
RB0
0
O
DIG
LATB<0> data output; not affected by analog input.
1
I
TTL
PORTB<0> data input; weak pull-up when RBPU bit is cleared.
Disabled when analog input enabled.(1)
External interrupt 0 input.
INT0
1
I
ST
1
I
ST
AN12
1
I
ANA
RB1
0
O
DIG
LATB<1> data output; not affected by analog input.
1
I
TTL
PORTB<1> data input; weak pull-up when RBPU bit is cleared.
Disabled when analog input enabled.(1)
RB6/KBI2/PGC
RB7/KBI3/PGD
Legend:
Note 1:
2:
3:
Enhanced PWM Fault input (ECCP1 module); enabled in software.
A/D input channel 12.(1)
INT1
1
I
ST
AN10
1
I
ANA
A/D input channel 10.(1)
RB2
0
O
DIG
LATB<2> data output; not affected by analog input.
1
I
TTL
PORTB<2> data input; weak pull-up when RBPU bit is cleared.
Disabled when analog input enabled.(1)
External interrupt 1 input.
INT2
1
I
ST
AN8
1
I
ANA
A/D input channel 8.(1)
RB3
0
O
DIG
LATB<3> data output; not affected by analog input.
1
I
TTL
PORTB<3> data input; weak pull-up when RBPU bit is cleared.
Disabled when analog input enabled.(1)
1
I
ANA
A/D input channel 9.(1)
0
O
DIG
CCP2 compare and PWM output.
1
I
ST
CCP2 capture input
0
O
DIG
LATB<4> data output; not affected by analog input.
1
I
TTL
PORTB<4> data input; weak pull-up when RBPU bit is cleared.
Disabled when analog input enabled.(1)
KBI0
1
I
TTL
Interrupt on pin change.
AN11
1
I
ANA
A/D input channel 11.(1)
RB5
0
O
DIG
LATB<5> data output.
1
I
TTL
PORTB<5> data input; weak pull-up when RBPU bit is cleared.
CCP2
RB5/KBI1/PGM
Description
FLT0
AN9
RB4/KBI0/AN11
I/O
Type
(2)
RB4
External interrupt 2 input.
KBI1
1
I
TTL
Interrupt on pin change.
PGM
x
I
ST
Single-Supply Programming mode entry (ICSP™). Enabled by LVP
configuration bit; all other pin functions disabled.
RB6
0
O
DIG
LATB<6> data output.
1
I
TTL
PORTB<6> data input; weak pull-up when RBPU bit is cleared.
KBI2
1
I
TTL
Interrupt on pin change.
PGC
x
I
ST
Serial execution (ICSP) clock input for ICSP and ICD operation.(3)
RB7
0
O
DIG
LATB<7> data output.
1
I
TTL
PORTB<7> data input; weak pull-up when RBPU bit is cleared.
KBI3
1
I
TTL
Interrupt on pin change.
PGD
x
O
DIG
Serial execution data output for ICSP and ICD operation.(3)
x
I
ST
Serial execution data input for ICSP and ICD operation.(3)
DIG = Digital level output; TTL = TTL input buffer; ST = Schmitt Trigger input buffer; ANA = Analog level input/output;
x = Don’t care (TRIS bit does not affect port direction or is overridden for this option).
Configuration on POR is determined by the PBADEN configuration bit. Pins are configured as analog inputs by default
when PBADEN is set and digital inputs when PBADEN is cleared.
Alternate assignment for CCP2 when the CCP2MX configuration bit is ‘0’. Default assignment is RC1.
All other pin functions are disabled when ICSP or ICD are enabled.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 99
PIC18F2X1X/4X1X
TABLE 9-4:
Name
PORTB
SUMMARY OF REGISTERS ASSOCIATED WITH PORTB
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
Values
on page
RB7
RB6
RB5
RB4
RB3
RB2
RB1
RB0
52
LATB
PORTB Data Latch Register (Read and Write to Data Latch)
52
TRISB
PORTB Data Direction Control Register
52
INTCON
GIE/GIEH PEIE/GIEL
TMR0IE
INT0IE
INTEDG0 INTEDG1 INTEDG2
RBIE
TMR0IF
INT0IF
RBIF
49
—
TMR0IP
—
RBIP
49
INTCON2
RBPU
INTCON3
INT2IP
INT1IP
—
INT2IE
INT1IE
—
INT2IF
INT1IF
49
ADCON1
—
—
VCFG1
VCFG0
PCFG3
PCFG2
PCFG1
PCFG0
51
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used by PORTB.
DS39636A-page 100
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
9.3
PORTC, TRISC and LATC
Registers
PORTC is an 8-bit wide, bidirectional port. The corresponding data direction register is TRISC. Setting a
TRISC bit (= 1) will make the corresponding PORTC
pin an input (i.e., put the corresponding output driver in
a high-impedance mode). Clearing a TRISC bit (= 0)
will make the corresponding PORTC pin an output (i.e.,
put the contents of the output latch on the selected pin).
The Data Latch register (LATC) is also memory
mapped. Read-modify-write operations on the LATC
register read and write the latched output value for
PORTC.
PORTC is multiplexed with several peripheral functions
(Table 9-5). The pins have Schmitt Trigger input
buffers. RC1 is normally configured by configuration bit
CCP2MX as the default peripheral pin of the CCP2
module (default/erased state, CCP2MX = 1).
The contents of the TRISC register are affected by
peripheral overrides. Reading TRISC always returns
the current contents, even though a peripheral device
may be overriding one or more of the pins.
EXAMPLE 9-3:
CLRF
PORTC
CLRF
LATC
MOVLW
0CFh
MOVWF
TRISC
INITIALIZING PORTC
;
;
;
;
;
;
;
;
;
;
;
;
Initialize PORTC by
clearing output
data latches
Alternate method
to clear output
data latches
Value used to
initialize data
direction
Set RC<3:0> as inputs
RC<5:4> as outputs
RC<7:6> as inputs
When enabling peripheral functions, care should be
taken in defining TRIS bits for each PORTC pin. Some
peripherals override the TRIS bit to make a pin an output,
while other peripherals override the TRIS bit to make a
pin an input. The user should refer to the corresponding
peripheral section for additional information.
Note:
On a Power-on Reset, these pins are
configured as digital inputs.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 101
PIC18F2X1X/4X1X
TABLE 9-5:
Pin
PORTC I/O SUMMARY
Function
TRIS
Setting
I/O
I/O
Type
RC0
0
O
DIG
RC0/T1OSO/
T13CKI
RC1/T1OSI/CCP2
RC2/CCP1/P1A
1
I
ST
x
O
ANA
T13CKI
1
I
ST
Timer1/Timer3 counter input.
RC1
0
O
DIG
LATC<1> data output.
1
I
ST
x
I
ANA
Timer1 oscillator input; enabled when Timer1 oscillator enabled.
Disables digital I/O.
CCP2(1)
0
O
DIG
CCP2 compare and PWM output; takes priority over port data.
1
I
ST
CCP2 capture input.
0
O
DIG
LATC<2> data output.
1
I
ST
PORTC<2> data input.
0
O
DIG
ECCP1 compare or PWM output; takes priority over port data.
1
I
ST
ECCP1 capture input.
0
O
DIG
ECCP1 Enhanced PWM output, channel A. May be configured for
tri-state during Enhanced PWM shutdown events. Takes priority over
port data.
0
O
DIG
LATC<3> data output.
1
I
ST
PORTC<3> data input.
0
O
DIG
SPI clock output (MSSP module); takes priority over port data.
RC2
P1A
RC3
SCK
SCL
RC5/SDO
RC7/RX/DT
Legend:
Note 1:
2:
RC4
PORTC<1> data input.
1
I
ST
SPI clock input (MSSP module).
0
O
DIG
I2C™ clock output (MSSP module); takes priority over port data.
1
I
0
O
DIG
LATC<4> data output.
PORTC<4> data input.
I2C/SMB I2C clock input (MSSP module); input type depends on module setting.
1
I
ST
SDI
1
I
ST
SPI™ data input (MSSP module).
SDA
1
O
DIG
I2C data output (MSSP module); takes priority over port data.
1
I
0
O
DIG
1
I
ST
PORTC<5> data input.
SDO
0
O
DIG
SPI data output (MSSP module); takes priority over port data.
RC6
0
O
DIG
LATC<6> data output.
RC5
RC6/TX/CK
PORTC<0> data input.
Timer1 oscillator output; enabled when Timer1 oscillator enabled.
Disables digital I/O.
T1OSI
(2)
RC4/SDI/SDA
LATC<0> data output.
T1OSO
CCP1
RC3/SCK/SCL
Description
I2C/SMB I2C data input (MSSP module); input type depends on module setting.
LATC<5> data output.
1
I
ST
PORTC<6> data input.
TX
1
O
DIG
Asynchronous serial transmit data output (USART module);
takes priority over port data. User must configure as output.
CK
1
O
DIG
Synchronous serial clock output (USART module); takes priority
over port data.
1
I
ST
Synchronous serial clock input (USART module).
0
O
DIG
LATC<7> data output.
1
I
ST
PORTC<7> data input.
RX
1
I
ST
Asynchronous serial receive data input (USART module).
DT
1
O
DIG
Synchronous serial data output (USART module); takes priority over
port data.
1
I
ST
Synchronous serial data input (USART module). User must
configure as an input.
RC7
DIG = Digital level output; TTL = TTL input buffer; ST = Schmitt Trigger input buffer; ANA = Analog level input/output;
I2C/SMB = I2C/SMBus input buffer; x = Don’t care (TRIS bit does not affect port direction or is overridden for this option).
Default assignment for CCP2 when the CCP2MX configuration bit is set. Alternate assignment is RB3.
Enhanced PWM output is available only on PIC18F4410/4510/4515/4610 devices.
DS39636A-page 102
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
TABLE 9-6:
Name
PORTC
SUMMARY OF REGISTERS ASSOCIATED WITH PORTC
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
Values
on page
RC7
RC6
RC5
RC4
RC3
RC2
RC1
RC0
52
LATC
PORTC Data Latch Register (Read and Write to Data Latch)
52
TRISC
PORTC Data Direction Control Register
52
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 103
PIC18F2X1X/4X1X
9.4
Note:
PORTD, TRISD and LATD
Registers
PORTD is only available on 40/44-pin
devices.
PORTD is an 8-bit wide, bidirectional port. The corresponding data direction register is TRISD. Setting a
TRISD bit (= 1) will make the corresponding PORTD
pin an input (i.e., put the corresponding output driver in
a high-impedance mode). Clearing a TRISD bit (= 0)
will make the corresponding PORTD pin an output (i.e.,
put the contents of the output latch on the selected pin).
The Data Latch register (LATD) is also memory
mapped. Read-modify-write operations on the LATD
register read and write the latched output value for
PORTD.
All pins on PORTD are implemented with Schmitt
Trigger input buffers. Each pin is individually
configurable as an input or output.
Three of the PORTD pins are multiplexed with outputs
P1B, P1C and P1D of the enhanced CCP module. The
operation of these additional PWM output pins is
covered in greater detail in Section 15.0 “Enhanced
Capture/Compare/PWM (ECCP) Module”.
Note:
PORTD can also be configured as an 8-bit wide microprocessor port (Parallel Slave Port) by setting control
bit, PSPMODE (TRISE<4>). In this mode, the input
buffers are TTL. See Section 9.6 “Parallel Slave
Port” for additional information on the Parallel Slave
Port (PSP).
Note:
When the enhanced PWM mode is used
with either dual or quad outputs, the PSP
functions of PORTD are automatically
disabled.
EXAMPLE 9-4:
CLRF
PORTD
CLRF
LATD
MOVLW
0CFh
MOVWF
TRISD
INITIALIZING PORTD
;
;
;
;
;
;
;
;
;
;
;
;
Initialize PORTD by
clearing output
data latches
Alternate method
to clear output
data latches
Value used to
initialize data
direction
Set RD<3:0> as inputs
RD<5:4> as outputs
RD<7:6> as inputs
On a Power-on Reset, these pins are
configured as digital inputs.
DS39636A-page 104
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
TABLE 9-7:
Pin
RD0/PSP0
PORTD I/O SUMMARY
Function
TRIS
Setting
I/O
I/O
Type
RD0
0
O
DIG
1
I
ST
PORTD<0> data input.
x
O
DIG
PSP read data output (LATD<0>); takes priority over port data.
x
I
TTL
PSP write data input.
0
O
DIG
LATD<1> data output.
1
I
ST
PORTD<1> data input.
PSP0
RD1/PSP1
RD1
PSP1
RD2/PSP2
RD2
PSP2
RD3/PSP3
RD3
PSP3
RD4/PSP4
RD4
PSP4
RD5/PSP5/P1B
RD5
RD7/PSP7/P1D
x
O
DIG
PSP read data output (LATD<1>); takes priority over port data.
x
I
TTL
PSP write data input.
0
O
DIG
LATD<2> data output.
1
I
ST
PORTD<2> data input.
x
O
DIG
PSP read data output (LATD<2>); takes priority over port data.
x
I
TTL
PSP write data input.
0
O
DIG
LATD<3> data output.
1
I
ST
PORTD<3> data input.
x
O
DIG
PSP read data output (LATD<3>); takes priority over port data.
x
I
TTL
PSP write data input.
0
O
DIG
LATD<4> data output.
1
I
ST
PORTD<4> data input.
x
O
DIG
PSP read data output (LATD<4>); takes priority over port data.
x
I
TTL
PSP write data input.
0
O
DIG
LATD<5> data output.
I
ST
PORTD<5> data input.
x
O
DIG
PSP read data output (LATD<5>); takes priority over port data.
x
I
TTL
PSP write data input.
P1B
0
O
DIG
ECCP1 Enhanced PWM output, channel B; takes priority over port and
PSP data. May be configured for tri-state during Enhanced PWM
shutdown events.
RD6
0
O
DIG
LATD<6> data output.
1
I
ST
PORTD<6> data input.
PSP6
x
O
DIG
PSP read data output (LATD<6>); takes priority over port data.
x
I
TTL
PSP write data input.
P1C
0
O
DIG
ECCP1 Enhanced PWM output, channel C; takes priority over port and
PSP data. May be configured for tri-state during Enhanced PWM
shutdown events.
RD7
0
O
DIG
LATD<7> data output.
1
I
ST
PORTD<7> data input.
PSP7
P1D
Legend:
LATD<0> data output.
1
PSP5
RD6/PSP6/P1C
Description
x
O
DIG
PSP read data output (LATD<7>); takes priority over port data.
x
I
TTL
PSP write data input.
0
O
DIG
ECCP1 Enhanced PWM output, channel D; takes priority over port and
PSP data. May be configured for tri-state during Enhanced PWM
shutdown events.
DIG = Digital level output; TTL = TTL input buffer; ST = Schmitt Trigger input buffer; x = Don’t care
(TRIS bit does not affect port direction or is overridden for this option).
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 105
PIC18F2X1X/4X1X
TABLE 9-8:
Name
PORTD
SUMMARY OF REGISTERS ASSOCIATED WITH PORTD
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
Values
on page
RD7
RD6
RD5
RD4
RD3
RD2
RD1
RD0
52
LATD
PORTD Data Latch Register (Read and Write to Data Latch)
52
TRISD
PORTD Data Direction Control Register
52
TRISE
CCP1CON
IBF
OBF
IBOV
PSPMODE
—
TRISE2
TRISE1
TRISE0
52
P1M1
P1M0
DC1B1
DC1B0
CCP1M3
CCP1M2
CCP1M1
CCP1M0
51
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used by PORTD.
DS39636A-page 106
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
9.5
PORTE, TRISE and LATE
Registers
Depending on the particular PIC18F2X1X/4X1X device
selected, PORTE is implemented in two different ways.
For 40/44-pin devices, PORTE is a 4-bit wide port.
Three pins (RE0/RD/AN5, RE1/WR/AN6 and RE2/CS/
AN7) are individually configurable as inputs or outputs.
These pins have Schmitt Trigger input buffers. When
selected as an analog input, these pins will read as ‘0’s.
The corresponding data direction register is TRISE.
Setting a TRISE bit (= 1) will make the corresponding
PORTE pin an input (i.e., put the corresponding output
driver in a high-impedance mode). Clearing a TRISE bit
(= 0) will make the corresponding PORTE pin an output
(i.e., put the contents of the output latch on the selected
pin).
TRISE controls the direction of the RE pins, even when
they are being used as analog inputs. The user must
make sure to keep the pins configured as inputs when
using them as analog inputs.
Note:
On a Power-on Reset, RE2:RE0 are
configured as analog inputs.
The upper four bits of the TRISE register also control
the operation of the Parallel Slave Port. Their operation
is explained in Register 9-1.
The Data Latch register (LATE) is also memory
mapped. Read-modify-write operations on the LATE
register, read and write the latched output value for
PORTE.
 2004 Microchip Technology Inc.
The fourth pin of PORTE (MCLR/VPP/RE3) is an input
only pin. Its operation is controlled by the MCLRE configuration bit. When selected as a port pin (MCLRE = 0),
it functions as a digital input only pin; as such, it does not
have TRIS or LAT bits associated with its operation.
Otherwise, it functions as the device’s Master Clear
input. In either configuration, RE3 also functions as the
programming voltage input during programming.
Note:
On a Power-on Reset, RE3 is enabled as
a digital input only if Master Clear
functionality is disabled.
EXAMPLE 9-5:
CLRF
CLRF
MOVLW
MOVWF
MOVLW
MOVWF
9.5.1
PORTE
;
;
;
LATE
;
;
;
0Ah
;
ADCON1 ;
03h
;
;
;
TRISE
;
;
;
INITIALIZING PORTE
Initialize PORTE by
clearing output
data latches
Alternate method
to clear output
data latches
Configure A/D
for digital inputs
Value used to
initialize data
direction
Set RE<0> as inputs
RE<1> as outputs
RE<2> as inputs
PORTE IN 28-PIN DEVICES
For 28-pin devices, PORTE is only available when
Master Clear functionality is disabled (MCLRE = 0). In
these cases, PORTE is a single bit, input only port
comprised of RE3 only. The pin operates as previously
described.
Preliminary
DS39636A-page 107
PIC18F2X1X/4X1X
REGISTER 9-1:
TRISE REGISTER (40/44-PIN DEVICES ONLY)
R-0
R-0
R/W-0
R/W-0
U-0
R/W-1
R/W-1
R/W-1
IBF
OBF
IBOV
PSPMODE
—
TRISE2
TRISE1
TRISE0
bit 7
bit 0
bit 7
IBF: Input Buffer Full Status bit
1 = A word has been received and waiting to be read by the CPU
0 = No word has been received
bit 6
OBF: Output Buffer Full Status bit
1 = The output buffer still holds a previously written word
0 = The output buffer has been read
bit 5
IBOV: Input Buffer Overflow Detect bit (in Microprocessor mode)
1 = A write occurred when a previously input word has not been read (must be cleared in software)
0 = No overflow occurred
bit 4
PSPMODE: Parallel Slave Port Mode Select bit
1 = Parallel Slave Port mode
0 = General purpose I/O mode
bit 3
Unimplemented: Read as ‘0’
bit 2
TRISE2: RE2 Direction Control bit
1 = Input
0 = Output
bit 1
TRISE1: RE1 Direction Control bit
1 = Input
0 = Output
bit 0
TRISE0: RE0 Direction Control bit
1 = Input
0 = Output
Legend:
DS39636A-page 108
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
Preliminary
x = Bit is unknown
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
TABLE 9-9:
PORTE I/O SUMMARY
Pin
Function
TRIS
Setting
I/O
I/O
Type
RE0
0
O
DIG
LATE<0> data output; not affected by analog input.
1
I
ST
PORTE<0> data input; disabled when analog input enabled.
RE0/RD/AN5
RE1/WR/AN6
RE2/CS/AN7
MCLR/VPP/RE3(1)
Legend:
Note 1:
2:
PORTE
(2)
RD
1
I
TTL
PSP read enable input (PSP enabled).
AN5
1
I
ANA
A/D input channel 5; default input configuration on POR.
RE1
0
O
DIG
LATE<1> data output; not affected by analog input.
1
I
ST
PORTE<1> data input; disabled when analog input enabled.
WR
1
I
TTL
PSP write enable input (PSP enabled).
AN6
1
I
ANA
A/D input channel 6; default input configuration on POR.
RE2
0
O
DIG
LATE<2> data output; not affected by analog input.
1
I
ST
PORTE<2> data input; disabled when analog input enabled.
CS
1
I
TTL
PSP write enable input (PSP enabled).
AN7
1
I
ANA
A/D input channel 7; default input configuration on POR.
MCLR
—
I
ST
External Master Clear input; enabled when MCLRE configuration bit is
set.
VPP
—
I
ANA
High-voltage detection; used for ICSP™ mode entry detection. Always
available, regardless of pin mode.
RE3
—(2)
I
ST
PORTE<3> data input; enabled when MCLRE configuration bit is clear.
DIG = Digital level output; TTL = TTL input buffer; ST = Schmitt Trigger input buffer; ANA = Analog level input/output;
x = Don’t care (TRIS bit does not affect port direction or is overridden for this option).
RE3 is available on both 28-pin and 40/44-pin devices. All other PORTE pins are only implemented on 40/44-pin
devices.
RE3 does not have a corresponding TRIS bit to control data direction.
TABLE 9-10:
Name
Description
SUMMARY OF REGISTERS ASSOCIATED WITH PORTE
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
Values
on page
—
—
—
—
RE3(1,2)
RE2
RE1
RE0
52
LATE
—
—
—
—
—
TRISE
IBF
OBF
IBOV
PSPMODE
—
LATE Data Output Register
TRISE2
TRISE1
TRISE0
52
52
ADCON1
—
—
VCFG1
VCFG0
PCFG3
PCFG2
PCFG1
PCFG0
51
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used by PORTE.
Note 1: Implemented only when Master Clear functionality is disabled (MCLRE configuration bit = 0).
2: RE3 is the only PORTE bit implemented on both 28-pin and 40/44-pin devices. All other bits are
implemented only when PORTE is implemented (i.e., 40/44-pin devices).
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 109
PIC18F2X1X/4X1X
9.6
Note:
Parallel Slave Port
The Parallel Slave Port is only available on
40/44-pin devices.
In addition to its function as a general I/O port, PORTD
can also operate as an 8-bit wide Parallel Slave Port
(PSP) or microprocessor port. PSP operation is controlled by the 4 upper bits of the TRISE register
(Register 9-1). Setting control bit, PSPMODE
(TRISE<4>), enables PSP operation as long as the
enhanced CCP module is not operating in dual output
or quad output PWM mode. In Slave mode, the port is
asynchronously readable and writable by the external
world.
The timing for the control signals in Write and Read
modes is shown in Figure 9-3 and Figure 9-4,
respectively.
FIGURE 9-2:
The PSP can directly interface to an 8-bit microprocessor data bus. The external microprocessor can
read or write the PORTD latch as an 8-bit latch. Setting
the control bit PSPMODE enables the PORTE I/O pins
to become control inputs for the microprocessor port.
When set, port pin RE0 is the RD input, RE1 is the WR
input and RE2 is the CS (Chip Select) input. For this
functionality, the corresponding data direction bits of
the TRISE register (TRISE<2:0>) must be configured
as inputs (set). The A/D port configuration bits,
PFCG3:PFCG0 (ADCON1<3:0>), must also be set to a
value in the range of ‘1010’ through ‘1111’.
One bit of PORTD
Data Bus
D
WR LATD
or
WR PORTD
Preliminary
RDx pin
Data Latch
RD PORTD
TTL
D
ENEN
RD LATD
Set Interrupt Flag
PSPIF (PIR1<7>)
PORTE Pins
Read
A read from the PSP occurs when both the CS and RD
lines are first detected low. The data in PORTD is read
out and the OBF bit is clear. If the user writes new data
to PORTD to set OBF, the data is immediately read out;
however, the OBF bit is not set.
DS39636A-page 110
Q
CK
Q
A write to the PSP occurs when both the CS and WR
lines are first detected low and ends when either are
detected high. The PSPIF and IBF flag bits are both set
when the write ends.
When either the CS or RD lines are detected high, the
PORTD pins return to the input state and the PSPIF bit
is set. User applications should wait for PSPIF to be set
before servicing the PSP; when this happens, the IBF
and OBF bits can be polled and the appropriate action
taken.
PORTD AND PORTE
BLOCK DIAGRAM
(PARALLEL SLAVE PORT)
TTL
RD
Chip Select
TTL
CS
Write
TTL
Note:
WR
I/O pins have diode protection to VDD and VSS.
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
FIGURE 9-3:
PARALLEL SLAVE PORT WRITE WAVEFORMS
Q1
Q2
Q3
Q4
Q1
Q2
Q3
Q4
Q1
Q2
Q3
Q4
Q4
Q1
Q2
Q3
Q4
CS
WR
RD
PORTD<7:0>
IBF
OBF
PSPIF
FIGURE 9-4:
PARALLEL SLAVE PORT READ WAVEFORMS
Q1
Q2
Q3
Q4
Q1
Q2
Q3
CS
WR
RD
PORTD<7:0>
IBF
OBF
PSPIF
TABLE 9-11:
REGISTERS ASSOCIATED WITH PARALLEL SLAVE PORT
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
Values
on page
PORTD
RD7
RD6
RD5
RD4
RD3
RD2
RD1
RD0
52
LATD
PORTD Data Latch Register (Read and Write to Data Latch)
52
TRISD
PORTD Data Direction Control Register
52
PORTE
—
—
—
—
RE3
LATE
—
—
—
—
—
IBF
OBF
IBOV
PSPMODE
—
TRISE2
TRISE1
TRISE0
52
TMR0IF
INT0IE
RBIE
TMR0IF
INT0IF
RBIF
49
TRISE
RE2
RE1
RE0
LATE Data Output bits
52
52
INTCON
GIE/GIEH PEIE/GIEL
PIR1
PSPIF(1)
ADIF
RCIF
TXIF
SSPIF
CCP1IF
TMR2IF
TMR1IF
52
PIE1
PSPIE(1)
ADIE
RCIE
TXIE
SSPIE
CCP1IE
TMR2IE
TMR1IE
52
IPR1
PSPIP(1)
ADIP
RCIP
TXIP
SSPIP
CCP1IP
TMR2IP
TMR1IP
52
—
—
VCFG1
VCFG0
PCFG3
PCFG2
PCFG1
PCFG0
51
ADCON1
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used by the Parallel Slave Port.
Note 1: These bits are unimplemented on 28-pin devices and read as ‘0’.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 111
PIC18F2X1X/4X1X
NOTES:
DS39636A-page 112
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
10.0
TIMER0 MODULE
The Timer0 module incorporates the following features:
• Software selectable operation as a timer or
counter in both 8-bit or 16-bit modes
• Readable and writable registers
• Dedicated 8-bit, software programmable
prescaler
• Selectable clock source (internal or external)
• Edge select for external clock
• Interrupt-on-overflow
REGISTER 10-1:
The T0CON register (Register 10-1) controls all
aspects of the module’s operation, including the
prescale selection. It is both readable and writable.
A simplified block diagram of the Timer0 module in 8-bit
mode is shown in Figure 10-1. Figure 10-2 shows a
simplified block diagram of the Timer0 module in 16-bit
mode.
T0CON: TIMER0 CONTROL REGISTER
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
TMR0ON
T08BIT
T0CS
T0SE
PSA
T0PS2
T0PS1
T0PS0
bit 7
bit 0
bit 7
TMR0ON: Timer0 On/Off Control bit
1 = Enables Timer0
0 = Stops Timer0
bit 6
T08BIT: Timer0 8-bit/16-bit Control bit
1 = Timer0 is configured as an 8-bit timer/counter
0 = Timer0 is configured as a 16-bit timer/counter
bit 5
T0CS: Timer0 Clock Source Select bit
1 = Transition on T0CKI pin
0 = Internal instruction cycle clock (CLKO)
bit 4
T0SE: Timer0 Source Edge Select bit
1 = Increment on high-to-low transition on T0CKI pin
0 = Increment on low-to-high transition on T0CKI pin
bit 3
PSA: Timer0 Prescaler Assignment bit
1 = TImer0 prescaler is NOT assigned. Timer0 clock input bypasses prescaler.
0 = Timer0 prescaler is assigned. Timer0 clock input comes from prescaler output.
bit 2-0
T0PS2:T0PS0: Timer0 Prescaler Select bits
111 = 1:256 Prescale value
110 = 1:128 Prescale value
101 = 1:64 Prescale value
100 = 1:32 Prescale value
011 = 1:16 Prescale value
010 = 1:8 Prescale value
001 = 1:4 Prescale value
000 = 1:2 Prescale value
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
 2004 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS39636A-page 113
PIC18F2X1X/4X1X
10.1
Timer0 Operation
Timer0 can operate as either a timer or a counter; the
mode is selected with the T0CS bit (T0CON<5>). In
Timer mode (T0CS = 0), the module increments on
every clock by default unless a different prescaler value
is selected (see Section 10.3 “Prescaler”). If the
TMR0 register is written to, the increment is inhibited
for the following two instruction cycles. The user can
work around this by writing an adjusted value to the
TMR0 register.
The Counter mode is selected by setting the T0CS bit
(= 1). In this mode, Timer0 increments either on every
rising or falling edge of pin RA4/T0CKI. The incrementing edge is determined by the Timer0 Source Edge
Select bit, T0SE (T0CON<4>); clearing this bit selects
the rising edge. Restrictions on the external clock input
are discussed below.
An external clock source can be used to drive Timer0;
however, it must meet certain requirements to ensure
that the external clock can be synchronized with the
FIGURE 10-1:
internal phase clock (TOSC). There is a delay between
synchronization and the onset of incrementing the
timer/counter.
10.2
Timer0 Reads and Writes in
16-Bit Mode
TMR0H is not the actual high byte of Timer0 in 16-bit
mode; it is actually a buffered version of the real high
byte of Timer0 which is not directly readable nor
writable (refer to Figure 10-2). TMR0H is updated with
the contents of the high byte of Timer0 during a read of
TMR0L. This provides the ability to read all 16 bits of
Timer0 without having to verify that the read of the high
and low byte were valid, due to a rollover between
successive reads of the high and low byte.
Similarly, a write to the high byte of Timer0 must also
take place through the TMR0H Buffer register. The high
byte is updated with the contents of TMR0H when a
write occurs to TMR0L. This allows all 16 bits of Timer0
to be updated at once.
TIMER0 BLOCK DIAGRAM (8-BIT MODE)
FOSC/4
0
1
1
Programmable
Prescaler
T0CKI pin
T0SE
T0CS
0
Sync with
Internal
Clocks
Set
TMR0IF
on Overflow
TMR0L
(2 TCY Delay)
8
3
T0PS2:T0PS0
8
PSA
Note:
Internal Data Bus
Upon Reset, Timer0 is enabled in 8-bit mode with clock input from T0CKI max. prescale.
FIGURE 10-2:
TIMER0 BLOCK DIAGRAM (16-BIT MODE)
FOSC/4
0
0
1
Programmable
Prescaler
T0CKI pin
T0SE
T0CS
1
Sync with
Internal
Clocks
TMR0
High Byte
TMR0L
8
Set
TMR0IF
on Overflow
(2 TCY Delay)
3
Read TMR0L
T0PS2:T0PS0
Write TMR0L
PSA
8
8
TMR0H
8
8
Internal Data Bus
Note:
Upon Reset, Timer0 is enabled in 8-bit mode with clock input from T0CKI max. prescale.
DS39636A-page 114
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
10.3
10.3.1
Prescaler
An 8-bit counter is available as a prescaler for the Timer0
module. The prescaler is not directly readable or writable;
its value is set by the PSA and T0PS2:T0PS0 bits
(T0CON<3:0>), which determine the prescaler
assignment and prescale ratio.
Clearing the PSA bit assigns the prescaler to the
Timer0 module. When it is assigned, prescale values
from 1:2 through 1:256 in power-of-2 increments are
selectable.
When assigned to the Timer0 module, all instructions
writing to the TMR0 register (e.g., CLRF TMR0, MOVWF
TMR0, BSF TMR0, etc.) clear the prescaler count.
Note:
Writing to TMR0 when the prescaler is
assigned to Timer0 will clear the prescaler
count but will not change the prescaler
assignment.
TABLE 10-1:
Name
SWITCHING PRESCALER
ASSIGNMENT
The prescaler assignment is fully under software
control and can be changed “on-the-fly” during program
execution.
10.4
Timer0 Interrupt
The TMR0 interrupt is generated when the TMR0
register overflows from FFh to 00h in 8-bit mode, or from
FFFFh to 0000h in 16-bit mode. This overflow sets the
TMR0IF flag bit. The interrupt can be masked by clearing the TMR0IE bit (INTCON<5>). Before re-enabling
the interrupt, the TMR0IF bit must be cleared in software
by the Interrupt Service Routine.
Since Timer0 is shut down in Sleep mode, the TMR0
interrupt cannot awaken the processor from Sleep.
REGISTERS ASSOCIATED WITH TIMER0
Bit 7
Bit 6
Bit 5
TMR0L
Timer0 Register, Low Byte
TMR0H
Timer0 Register, High Byte
INTCON
GIE/GIEH PEIE/GIEL TMR0IE
T0CON
TMR0ON
T08BIT
TRISA
RA7(1)
RA6(1)
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
Values
on page
50
50
INT0IE
RBIE
TMR0IF
INT0IF
RBIF
49
T0CS
T0SE
PSA
T0PS2
T0PS1
T0PS0
50
RA5
RA4
RA3
RA2
RA1
RA0
52
Legend: Shaded cells are not used by Timer0.
Note 1: PORTA<7:6> and their direction bits are individually configured as port pins based on various primary
oscillator modes. When disabled, these bits read as ‘0’.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 115
PIC18F2X1X/4X1X
NOTES:
DS39636A-page 116
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
11.0
TIMER1 MODULE
The Timer1 timer/counter module incorporates these
features:
• Software selectable operation as a 16-bit timer or
counter
• Readable and writable 8-bit registers (TMR1H
and TMR1L)
• Selectable clock source (internal or external) with
device clock or Timer1 oscillator internal options
• Interrupt-on-overflow
• Reset on CCP special event trigger
• Device clock status flag (T1RUN)
REGISTER 11-1:
A simplified block diagram of the Timer1 module is
shown in Figure 11-1. A block diagram of the module’s
operation in Read/Write mode is shown in Figure 11-2.
The module incorporates its own low-power oscillator
to provide an additional clocking option. The Timer1
oscillator can also be used as a low-power clock source
for the microcontroller in power managed operation.
Timer1 can also be used to provide Real-Time Clock
(RTC) functionality to applications with only a minimal
addition of external components and code overhead.
Timer1 is controlled through the T1CON Control
register (Register 11-1). It also contains the Timer1
Oscillator Enable bit (T1OSCEN). Timer1 can be
enabled or disabled by setting or clearing control bit,
TMR1ON (T1CON<0>).
T1CON: TIMER1 CONTROL REGISTER
R/W-0
R-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
RD16
T1RUN
T1CKPS1
T1CKPS0
T1OSCEN
T1SYNC
TMR1CS
TMR1ON
bit 7
bit 0
bit 7
RD16: 16-bit Read/Write Mode Enable bit
1 = Enables register read/write of TImer1 in one 16-bit operation
0 = Enables register read/write of Timer1 in two 8-bit operations
bit 6
T1RUN: Timer1 System Clock Status bit
1 = Device clock is derived from Timer1 oscillator
0 = Device clock is derived from another source
bit 5-4
T1CKPS1:T1CKPS0: Timer1 Input Clock Prescale Select bits
11 = 1:8 Prescale value
10 = 1:4 Prescale value
01 = 1:2 Prescale value
00 = 1:1 Prescale value
bit 3
T1OSCEN: Timer1 Oscillator Enable bit
1 = Timer1 oscillator is enabled
0 = Timer1 oscillator is shut off
The oscillator inverter and feedback resistor are turned off to eliminate power drain.
bit 2
T1SYNC: Timer1 External Clock Input Synchronization Select bit
When TMR1CS = 1:
1 = Do not synchronize external clock input
0 = Synchronize external clock input
When TMR1CS = 0:
This bit is ignored. Timer1 uses the internal clock when TMR1CS = 0.
bit 1
TMR1CS: Timer1 Clock Source Select bit
1 = External clock from pin RC0/T1OSO/T13CKI (on the rising edge)
0 = Internal clock (FOSC/4)
bit 0
TMR1ON: Timer1 On bit
1 = Enables Timer1
0 = Stops Timer1
Legend:
R = Readable bit
-n = Value at POR
 2004 Microchip Technology Inc.
W = Writable bit
‘1’ = Bit is set
Preliminary
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
x = Bit is unknown
DS39636A-page 117
PIC18F2X1X/4X1X
11.1
Timer1 Operation
cycle (Fosc/4). When the bit is set, Timer1 increments
on every rising edge of the Timer1 external clock input
or the Timer1 oscillator, if enabled.
Timer1 can operate in one of these modes:
• Timer
• Synchronous Counter
• Asynchronous Counter
When Timer1 is enabled, the RC1/T1OSI and RC0/
T1OSO/T13CKI pins become inputs. This means the
values of TRISC<1:0> are ignored and the pins are
read as ‘0’.
The operating mode is determined by the clock select
bit, TMR1CS (T1CON<1>). When TMR3CS is cleared
(= 0), Timer1 increments on every internal instruction
FIGURE 11-1:
TIMER1 BLOCK DIAGRAM
Timer1 Oscillator
Timer1 Clock Input
1
On/Off
T1OSO/T13CKI
1
T1OSI
Synchronize
Prescaler
1, 2, 4, 8
FOSC/4
Internal
Clock
0
Detect
0
2
T1OSCEN(1)
Sleep Input
Timer1
On/Off
TMR1CS
T1CKPS1:T1CKPS0
T1SYNC
TMR1ON
Clear TMR1
(CCP Special Event Trigger)
Set
TMR1IF
on Overflow
TMR1
High Byte
TMR1L
Note 1: When enable bit, T1OSCEN, is cleared, the inverter and feedback resistor are turned off to eliminate power drain.
FIGURE 11-2:
TIMER1 BLOCK DIAGRAM (16-BIT READ/WRITE MODE)
Timer1 Oscillator
Timer1 Clock Input
1
T1OSO/T13CKI
1
FOSC/4
Internal
Clock
T1OSI
Synchronize
Prescaler
1, 2, 4, 8
0
Detect
0
2
T1OSCEN(1)
Sleep Input
Timer1
On/Off
TMR1CS
T1CKPS1:T1CKPS0
T1SYNC
TMR1ON
Clear TMR1
(CCP Special Event Trigger)
TMR1
High Byte
TMR1L
8
Set
TMR1IF
on Overflow
Read TMR1L
Write TMR1L
8
8
TMR1H
8
8
Internal Data Bus
Note 1: When enable bit, T1OSCEN, is cleared, the inverter and feedback resistor are turned off to eliminate power drain.
DS39636A-page 118
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
11.2
TABLE 11-1:
Timer1 16-Bit Read/Write Mode
Timer1 can be configured for 16-bit reads and writes
(see Figure 11-2). When the RD16 control bit
(T1CON<7>) is set, the address for TMR1H is mapped
to a buffer register for the high byte of Timer1. A read
from TMR1L will load the contents of the high byte of
Timer1 into the Timer1 high byte buffer. This provides
the user with the ability to accurately read all 16 bits of
Timer1 without having to determine whether a read of
the high byte, followed by a read of the low byte, has
become invalid due to a rollover between reads.
Osc Type
Freq
C1
C2
LP
32 kHz
27 pF(1)
27 pF(1)
Note 1: Microchip suggests these values as a
starting point in validating the oscillator
circuit.
2: Higher capacitance increases the stability
of the oscillator but also increases the
start-up time.
A write to the high byte of Timer1 must also take place
through the TMR1H Buffer register. The Timer1 high
byte is updated with the contents of TMR1H when a
write occurs to TMR1L. This allows a user to write all
16 bits to both the high and low bytes of Timer1 at once.
The high byte of Timer1 is not directly readable or
writable in this mode. All reads and writes must take
place through the Timer1 High Byte Buffer register.
Writes to TMR1H do not clear the Timer1 prescaler.
The prescaler is only cleared on writes to TMR1L.
11.3
Timer1 Oscillator
An on-chip crystal oscillator circuit is incorporated
between pins T1OSI (input) and T1OSO (amplifier
output). It is enabled by setting the Timer1 Oscillator
Enable bit, T1OSCEN (T1CON<3>). The oscillator is a
low-power circuit rated for 32 kHz crystals. It will
continue to run during all power managed modes. The
circuit for a typical LP oscillator is shown in Figure 11-3.
Table 11-1 shows the capacitor selection for the Timer1
oscillator.
The user must provide a software time delay to ensure
proper start-up of the Timer1 oscillator.
FIGURE 11-3:
EXTERNAL
COMPONENTS FOR THE
TIMER1 LP OSCILLATOR
C1
27 pF
PIC18FXXXX
XTAL
32.768 kHz
T1OSO
C2
27 pF
Note:
3: Since each resonator/crystal has its own
characteristics, the user should consult
the resonator/crystal manufacturer for
appropriate
values
of
external
components.
4: Capacitor values are for design guidance
only.
11.3.1
See the Notes with Table 11-1 for additional
information about capacitor selection.
USING TIMER1 AS A
CLOCK SOURCE
The Timer1 oscillator is also available as a clock source
in power managed modes. By setting the clock select
bits, SCS1:SCS0 (OSCCON<1:0>), to ‘01’, the device
switches to SEC_RUN mode; both the CPU and
peripherals are clocked from the Timer1 oscillator. If the
IDLEN bit (OSCCON<7>) is cleared and a SLEEP
instruction is executed, the device enter SEC_IDLE
mode. Additional details are available in Section 3.0
“Power Managed Modes”.
Whenever the Timer1 oscillator is providing the clock
source, the Timer1 system clock status flag, T1RUN
(T1CON<6>), is set. This can be used to determine the
controller’s current clocking mode. It can also indicate
the clock source being currently used by the Fail-Safe
Clock Monitor. If the Clock Monitor is enabled and the
Timer1 oscillator fails while providing the clock, polling
the T1RUN bit will indicate whether the clock is being
provided by the Timer1 oscillator or another source.
11.3.2
T1OSI
CAPACITOR SELECTION FOR
THE TIMER OSCILLATOR
LOW-POWER TIMER1 OPTION
The Timer1 oscillator can operate at two distinct levels
of power consumption based on device configuration.
When the LPT1OSC configuration bit is set, the Timer1
oscillator operates in a low-power mode. When
LPT1OSC is not set, Timer1 operates at a higher power
level. Power consumption for a particular mode is relatively constant, regardless of the device’s operating
mode. The default Timer1 configuration is the higher
power mode.
As the low-power Timer1 mode tends to be more sensitive to interference, high noise environments may
cause some oscillator instability. The low-power option
is, therefore, best suited for low noise applications
where power conservation is an important design
consideration.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 119
PIC18F2X1X/4X1X
11.3.3
TIMER1 OSCILLATOR LAYOUT
CONSIDERATIONS
11.5
The Timer1 oscillator circuit draws very little power
during operation. Due to the low-power nature of the
oscillator, it may also be sensitive to rapidly changing
signals in close proximity.
The oscillator circuit, shown in Figure 11-3, should be
located as close as possible to the microcontroller.
There should be no circuits passing within the oscillator
circuit boundaries other than VSS or VDD.
If a high-speed circuit must be located near the oscillator (such as the CCP1 pin in Output Compare or PWM
mode, or the primary oscillator using the OSC2 pin), a
grounded guard ring around the oscillator circuit, as
shown in Figure 11-4, may be helpful when used on a
single-sided PCB or in addition to a ground plane.
FIGURE 11-4:
OSCILLATOR CIRCUIT
WITH GROUNDED
GUARD RING
If either of the CCP modules is configured to use Timer1
and generate a Special Event Trigger in Compare mode
(CCP1M3:CCP1M0 or CCP2M3:CCP2M0 = 1011), this
signal will reset Timer1. The trigger from CCP2 will also
start an A/D conversion if the A/D module is enabled
(see Section 14.3.4 “Special Event Trigger” for more
information).
The module must be configured as either a timer or a
synchronous counter to take advantage of this feature.
When used this way, the CCPRH:CCPRL register pair
effectively becomes a period register for Timer1.
If Timer1 is running in Asynchronous Counter mode,
this Reset operation may not work.
In the event that a write to Timer1 coincides with a
special event trigger, the write operation will take
precedence.
Note:
VDD
VSS
11.6
OSC1
The special event triggers from the CCP2
module will not set the TMR1IF interrupt
flag bit (PIR1<0>).
Using Timer1 as a Real-Time Clock
Adding an external LP oscillator to Timer1 (such as the
one described in Section 11.3 “Timer1 Oscillator”
above) gives users the option to include RTC functionality to their applications. This is accomplished with an
inexpensive watch crystal to provide an accurate time
base and several lines of application code to calculate
the time. When operating in Sleep mode and using a
battery or supercapacitor as a power source, it can
completely eliminate the need for a separate RTC
device and battery backup.
OSC2
RC0
RC1
RC2
Note: Not drawn to scale.
11.4
Resetting Timer1 Using the CCP
Special Event Trigger
Timer1 Interrupt
The TMR1 register pair (TMR1H:TMR1L) increments
from 0000h to FFFFh and rolls over to 0000h. The
Timer1 interrupt, if enabled, is generated on overflow,
which is latched in interrupt flag bit, TMR1IF
(PIR1<0>). This interrupt can be enabled or disabled
by setting or clearing the Timer1 Interrupt Enable bit,
TMR1IE (PIE1<0>).
The application code routine, RTCisr, shown in
Example 11-1, demonstrates a simple method to
increment a counter at one-second intervals using an
Interrupt Service Routine. Incrementing the TMR1
register pair to overflow triggers the interrupt and calls
the routine, which increments the seconds counter by
one; additional counters for minutes and hours are
incremented as the previous counter overflow.
Since the register pair is 16 bits wide, counting up to
overflow the register directly from a 32.768 kHz clock
would take 2 seconds. To force the overflow at the
required one-second intervals, it is necessary to
preload it. The simplest method is to set the MSb of
TMR1H with a BSF instruction. Note that the TMR1L
register is never preloaded or altered. Doing so may
introduce cumulative errors over many cycles.
For this method to be accurate, Timer1 must operate in
Asynchronous mode and the Timer1 overflow interrupt
must be enabled (PIE1<0> = 1), as shown in the
routine, RTCinit. The Timer1 oscillator must also be
enabled and running at all times.
DS39636A-page 120
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
EXAMPLE 11-1:
IMPLEMENTING A REAL-TIME CLOCK USING A TIMER1 INTERRUPT SERVICE
RTCinit
MOVLW
MOVWF
CLRF
MOVLW
MOVWF
CLRF
CLRF
MOVLW
MOVWF
BSF
RETURN
80h
TMR1H
TMR1L
b’00001111’
T1CON
secs
mins
.12
hours
PIE1, TMR1IE
; Preload TMR1 register pair
; for 1 second overflow
BSF
BCF
INCF
MOVLW
CPFSGT
RETURN
CLRF
INCF
MOVLW
CPFSGT
RETURN
CLRF
INCF
MOVLW
CPFSGT
RETURN
CLRF
RETURN
TMR1H, 7
PIR1, TMR1IF
secs, F
.59
secs
;
;
;
;
Preload for 1 sec overflow
Clear interrupt flag
Increment seconds
60 seconds elapsed?
;
;
;
;
No, done
Clear seconds
Increment minutes
60 minutes elapsed?
;
;
;
;
No, done
clear minutes
Increment hours
24 hours elapsed?
; Configure for external clock,
; Asynchronous operation, external oscillator
; Initialize timekeeping registers
;
; Enable Timer1 interrupt
RTCisr
TABLE 11-2:
Name
secs
mins, F
.59
mins
mins
hours, F
.23
hours
; No, done
; Reset hours
; Done
hours
REGISTERS ASSOCIATED WITH TIMER1 AS A TIMER/COUNTER
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
Values
on page
INTCON
GIE/GIEH PEIE/GIEL
TMR0IE
INT0IE
RBIE
TMR0IF
INT0IF
RBIF
49
PIR1
PSPIF(1)
ADIF
RCIF
TXIF
SSPIF
CCP1IF
TMR2IF
TMR1IF
52
PIE1
PSPIE(1)
ADIE
RCIE
TXIE
SSPIE
CCP1IE
TMR2IE
TMR1IE
52
IPR1
PSPIP(1)
ADIP
RCIP
TXIP
SSPIP
CCP1IP
TMR2IP
TMR1IP
52
TMR1L
Timer1 Register, Low Byte
50
TMR1H
Timer1 Register, High Byte
50
T1CON
RD16
T1RUN
T1CKPS1 T1CKPS0 T1OSCEN T1SYNC
TMR1CS
TMR1ON
50
Legend: Shaded cells are not used by the Timer1 module.
Note 1: These bits are unimplemented on 28-pin devices and read as ‘0’.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 121
PIC18F2X1X/4X1X
NOTES:
DS39636A-page 122
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
12.0
TIMER2 MODULE
12.1
The Timer2 module timer incorporates the following
features:
• 8-bit timer and period registers (TMR2 and PR2,
respectively)
• Readable and writable (both registers)
• Software programmable prescaler (1:1, 1:4 and
1:16)
• Software programmable postscaler (1:1 through
1:16)
• Interrupt on TMR2-to-PR2 match
• Optional use as the shift clock for the MSSP
module
The module is controlled through the T2CON register
(Register 12-1), which enables or disables the timer
and configures the prescaler and postscaler. Timer2
can be shut off by clearing control bit, TMR2ON
(T2CON<2>), to minimize power consumption.
A simplified block diagram of the module is shown in
Figure 12-1.
Timer2 Operation
In normal operation, TMR2 is incremented from 00h on
each clock (FOSC/4). A 4-bit counter/prescaler on the
clock input gives direct input, divide-by-4 and divide-by16 prescale options; these are selected by the prescaler
control bits, T2CKPS1:T2CKPS0 (T2CON<1:0>). The
value of TMR2 is compared to that of the period register,
PR2, on each clock cycle. When the two values match,
the comparator generates a match signal as the timer
output. This signal also resets the value of TMR2 to 00h
on the next cycle and drives the output counter/
postscaler (see Section 12.2 “Timer2 Interrupt”).
The TMR2 and PR2 registers are both directly readable
and writable. The TMR2 register is cleared on any
device Reset, while the PR2 register initializes at FFh.
Both the prescaler and postscaler counters are cleared
on the following events:
• a write to the TMR2 register
• a write to the T2CON register
• any device Reset (Power-on Reset, MCLR Reset,
Watchdog Timer Reset or Brown-out Reset)
TMR2 is not cleared when T2CON is written.
REGISTER 12-1:
T2CON: TIMER2 CONTROL REGISTER
U-0
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
T2OUTPS3 T2OUTPS2 T2OUTPS1 T2OUTPS0 TMR2ON T2CKPS1
R/W-0
T2CKPS0
bit 7
bit 0
bit 7
Unimplemented: Read as ‘0’
bit 6-3
T2OUTPS3:T2OUTPS0: Timer2 Output Postscale Select bits
0000 = 1:1 Postscale
0001 = 1:2 Postscale
•
•
•
1111 = 1:16 Postscale
bit 2
TMR2ON: Timer2 On bit
1 = Timer2 is on
0 = Timer2 is off
bit 1-0
T2CKPS1:T2CKPS0: Timer2 Clock Prescale Select bits
00 = Prescaler is 1
01 = Prescaler is 4
1x = Prescaler is 16
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
 2004 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS39636A-page 123
PIC18F2X1X/4X1X
12.2
Timer2 Interrupt
12.3
Timer2 also can generate an optional device interrupt.
The Timer2 output signal (TMR2-to-PR2 match)
provides the input for the 4-bit output counter/
postscaler. This counter generates the TMR2 match
interrupt flag which is latched in TMR2IF (PIR1<1>).
The interrupt is enabled by setting the TMR2 Match
Interrupt Enable bit, TMR2IE (PIE1<1>).
Timer2 Output
The unscaled output of TMR2 is available primarily to
the CCP modules, where it is used as a time base for
operations in PWM mode.
Timer2 can be optionally used as the shift clock source
for the MSSP module operating in SPI mode. Additional information is provided in Section 16.0 “Master
Synchronous Serial Port (MSSP) Module”.
A range of 16 postscale options (from 1:1 through 1:16
inclusive) can be selected with the postscaler control
bits, T2OUTPS3:T2OUTPS0 (T2CON<6:3>).
FIGURE 12-1:
TIMER2 BLOCK DIAGRAM
4
1:1 to 1:16
Postscaler
T2OUTPS3:T2OUTPS0
Set TMR2IF
2
TMR2 Output
(to PWM or MSSP)
T2CKPS1:T2CKPS0
TMR2/PR2
Match
Reset
1:1, 1:4, 1:16
Prescaler
FOSC/4
TMR2
Comparator
8
PR2
8
8
Internal Data Bus
TABLE 12-1:
Name
REGISTERS ASSOCIATED WITH TIMER2 AS A TIMER/COUNTER
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
Values
on page
TMR0IE
INT0IE
RBIE
TMR0IF
INT0IF
RBIF
49
PIR1
PSPIF(1)
ADIF
RCIF
TXIF
SSPIF
CCP1IF
TMR2IF
TMR1IF
52
PIE1
PSPIE(1)
ADIE
RCIE
TXIE
SSPIE
CCP1IE
TMR2IE
TMR1IE
52
IPR1
PSPIP(1)
ADIP
RCIP
TXIP
SSPIP
CCP1IP
TMR2IP
TMR1IP
52
INTCON GIE/GIEH PEIE/GIEL
TMR2
T2CON
PR2
Timer2 Register
—
50
T2OUTPS3 T2OUTPS2 T2OUTPS1 T2OUTPS0 TMR2ON
T2CKPS1 T2CKPS0
Timer2 Period Register
50
50
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used by the Timer2 module.
Note 1: These bits are unimplemented on 28-pin devices and read as ‘0’.
DS39636A-page 124
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
13.0
TIMER3 MODULE
The Timer3 module timer/counter incorporates these
features:
• Software selectable operation as a 16-bit timer or
counter
• Readable and writable 8-bit registers (TMR3H
and TMR3L)
• Selectable clock source (internal or external) with
device clock or Timer1 oscillator internal options
• Interrupt-on-overflow
• Module Reset on CCP special event trigger
REGISTER 13-1:
A simplified block diagram of the Timer3 module is
shown in Figure 13-1. A block diagram of the module’s
operation in Read/Write mode is shown in Figure 13-2.
The Timer3 module is controlled through the T3CON
register (Register 13-1). It also selects the clock source
options for the CCP modules (see Section 14.1.1
“CCP Modules and Timer Resources” for more
information).
T3CON: TIMER3 CONTROL REGISTER
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
RD16
T3CCP2
T3CKPS1
T3CKPS0
T3CCP1
T3SYNC
TMR3CS
TMR3ON
bit 7
bit 0
bit 7
RD16: 16-bit Read/Write Mode Enable bit
1 = Enables register read/write of Timer3 in one 16-bit operation
0 = Enables register read/write of Timer3 in two 8-bit operations
bit 6,3
T3CCP2:T3CCP1: Timer3 and Timer1 to CCPx Enable bits
1x = Timer3 is the capture/compare clock source for the CCP modules
01 = Timer3 is the capture/compare clock source for CCP2;
Timer1 is the capture/compare clock source for CCP1
00 = Timer1 is the capture/compare clock source for the CCP modules
bit 5-4
T3CKPS1:T3CKPS0: Timer3 Input Clock Prescale Select bits
11 = 1:8 Prescale value
10 = 1:4 Prescale value
01 = 1:2 Prescale value
00 = 1:1 Prescale value
bit 2
T3SYNC: Timer3 External Clock Input Synchronization Control bit
(Not usable if the device clock comes from Timer1/Timer3.)
When TMR3CS = 1:
1 = Do not synchronize external clock input
0 = Synchronize external clock input
When TMR3CS = 0:
This bit is ignored. Timer3 uses the internal clock when TMR3CS = 0.
bit 1
TMR3CS: Timer3 Clock Source Select bit
1 = External clock input from Timer1 oscillator or T13CKI (on the rising edge after the first
falling edge)
0 = Internal clock (FOSC/4)
bit 0
TMR3ON: Timer3 On bit
1 = Enables Timer3
0 = Stops Timer3
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
 2004 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS39636A-page 125
PIC18F2X1X/4X1X
13.1
Timer3 Operation
The operating mode is determined by the clock select
bit, TMR3CS (T3CON<1>). When TMR3CS is cleared
(= 0), Timer3 increments on every internal instruction
cycle (FOSC/4). When the bit is set, Timer3 increments
on every rising edge of the Timer1 external clock input
or the Timer1 oscillator, if enabled.
Timer3 can operate in one of three modes:
• Timer
• Synchronous Counter
• Asynchronous Counter
As with Timer1, the RC1/T1OSI and RC0/T1OSO/
T13CKI pins become inputs when the Timer1 oscillator
is enabled. This means the values of TRISC<1:0> are
ignored and the pins are read as ‘0’.
FIGURE 13-1:
TIMER3 BLOCK DIAGRAM
Timer1 Oscillator
Timer1 Clock Input
1
T1OSO/T13CKI
1
T1OSI
Synchronize
Prescaler
1, 2, 4, 8
FOSC/4
Internal
Clock
0
Detect
0
2
T1OSCEN(1)
Sleep Input
Timer3
On/Off
TMR3CS
T3CKPS1:T3CKPS0
T3SYNC
TMR3ON
CCP1/CCP2 Special Event Trigger
CCP1/CCP2 Select from T3CON<6,3>
Clear TMR3
Set
TMR3IF
on Overflow
TMR3
High Byte
TMR3L
Note 1: When enable bit, T1OSCEN, is cleared, the inverter and feedback resistor are turned off to eliminate power drain.
FIGURE 13-2:
TIMER3 BLOCK DIAGRAM (16-BIT READ/WRITE MODE)
Timer1 Oscillator
Timer1 Clock Input
1
T13CKI/T1OSO
1
FOSC/4
Internal
Clock
T1OSI
Synchronize
Prescaler
1, 2, 4, 8
0
Detect
0
2
Sleep Input
TMR3CS
T1OSCEN(1)
T3CKPS1:T3CKPS0
Timer3
On/Off
T3SYNC
TMR3ON
CCP1/CCP2 Special Event Trigger
CCP1/CCP2 Select from T3CON<6,3>
Clear TMR3
Set
TMR3IF
on Overflow
TMR3
High Byte
TMR3L
8
Read TMR1L
Write TMR1L
8
8
TMR3H
8
8
Internal Data Bus
Note 1: When enable bit, T1OSCEN, is cleared, the inverter and feedback resistor are turned off to eliminate power drain.
DS39636A-page 126
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
13.2
Timer3 16-Bit Read/Write Mode
13.4
Timer3 Interrupt
Timer3 can be configured for 16-bit reads and writes
(see Figure 13-2). When the RD16 control bit
(T3CON<7>) is set, the address for TMR3H is mapped
to a buffer register for the high byte of Timer3. A read
from TMR3L will load the contents of the high byte of
Timer3 into the Timer3 High Byte Buffer register. This
provides the user with the ability to accurately read all
16 bits of Timer1 without having to determine whether
a read of the high byte, followed by a read of the low
byte, has become invalid due to a rollover between
reads.
The TMR3 register pair (TMR3H:TMR3L) increments
from 0000h to FFFFh and overflows to 0000h. The
Timer3 interrupt, if enabled, is generated on overflow
and is latched in interrupt flag bit, TMR3IF (PIR2<1>).
This interrupt can be enabled or disabled by setting or
clearing the Timer3 Interrupt Enable bit, TMR3IE
(PIE2<1>).
A write to the high byte of Timer3 must also take place
through the TMR3H Buffer register. The Timer3 high
byte is updated with the contents of TMR3H when a
write occurs to TMR3L. This allows a user to write all
16 bits to both the high and low bytes of Timer3 at once.
If either of the CCP modules is configured to use Timer3
and to generate a special event trigger in Compare mode
(CCP1M3:CCP1M0 or CCP2M3:CCP2M0 = 1011), this
signal will reset Timer3. It will also start an A/D conversion
if the A/D module is enabled (see Section 14.3.4
“Special Event Trigger” for more information).
The high byte of Timer3 is not directly readable or
writable in this mode. All reads and writes must take
place through the Timer3 High Byte Buffer register.
Writes to TMR3H do not clear the Timer3 prescaler.
The prescaler is only cleared on writes to TMR3L.
13.3
Using the Timer1 Oscillator as the
Timer3 Clock Source
The Timer1 internal oscillator may be used as the clock
source for Timer3. The Timer1 oscillator is enabled by
setting the T1OSCEN (T1CON<3>) bit. To use it as the
Timer3 clock source, the TMR3CS bit must also be set.
As previously noted, this also configures Timer3 to
increment on every rising edge of the oscillator source.
13.5
Resetting Timer3 Using the CCP
Special Event Trigger
The module must be configured as either a timer or
synchronous counter to take advantage of this feature.
When used this way, the CCPR2H:CCPR2L register
pair effectively becomes a period register for Timer3.
If Timer3 is running in Asynchronous Counter mode,
the Reset operation may not work.
In the event that a write to Timer3 coincides with a
special event trigger from a CCP module, the write will
take precedence.
Note:
The special event triggers from the CCP2
module will not set the TMR3IF interrupt
flag bit (PIR1<0>).
The Timer1 oscillator is described in Section 11.0
“Timer1 Module”.
TABLE 13-1:
Name
INTCON
REGISTERS ASSOCIATED WITH TIMER3 AS A TIMER/COUNTER
Bit 7
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
Values
on page
TMR0IE
INT0IE
RBIE
TMR0IF
INT0IF
RBIF
49
Bit 6
GIE/GIEH PEIE/GIEL
PIR2
OSCFIF
CMIF
—
—
BCLIF
HLVDIF
TMR3IF
CCP2IF
52
PIE2
OSCFIE
CMIE
—
—
BCLIE
HLVDIE
TMR3IE
CCP2IE
52
IPR2
OSCFIP
CMIP
—
—
BCLIP
HLVDIP
TMR3IP
CCP2IP
52
TMR3L
Timer3 Register, Low Byte
51
TMR3H
Timer3 Register, High Byte
51
T1CON
RD16
T1RUN
T1CKPS1 T1CKPS0 T1OSCEN T1SYNC
TMR1CS
TMR1ON
50
T3CON
RD16
T3CCP2
T3CKPS1 T3CKPS0
TMR3CS
TMR3ON
51
T3CCP1
T3SYNC
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used by the Timer3 module.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 127
PIC18F2X1X/4X1X
NOTES:
DS39636A-page 128
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
14.0
CAPTURE/COMPARE/PWM
(CCP) MODULES
The Capture and Compare operations described in this
chapter apply to all standard and Enhanced CCP
modules.
PIC18F2X1X/4X1X devices all have two CCP
(Capture/Compare/PWM) modules. Each module contains a 16-bit register which can operate as a 16-bit
Capture register, a 16-bit Compare register or a PWM
Master/Slave Duty Cycle register.
In 28-pin devices, the two standard CCP modules
(CCP1 and CCP2) operate as described in this chapter.
In 40/44-pin devices, CCP1 is implemented as an
Enhanced CCP module with standard Capture and
Compare modes and Enhanced PWM modes. The
ECCP implementation is discussed in Section 15.0
“Enhanced
Capture/Compare/PWM
(ECCP)
Module”.
REGISTER 14-1:
Note: Throughout this section and Section 15.0
“Enhanced Capture/Compare/PWM (ECCP)
Module”, references to the register and bit
names for CCP modules are referred to generically by the use of ‘x’ or ‘y’ in place of the
specific module number. Thus, “CCPxCON”
might refer to the control register for CCP1,
CCP2 or ECCP1. “CCPxCON” is used
throughout these sections to refer to the
module control register, regardless of whether
the CCP module is a standard or Enhanced
implementation.
CCPXCON REGISTER (CCP2 MODULE, CCP1 MODULE IN 28-PIN DEVICES)
U-0
U-0
R/W-0
R/W-0
R/W-0
R/W-0
—
—
DCxB1
DCxB0
CCPxM3
CCPxM2
R/W-0
R/W-0
CCPxM1 CCPxM0
bit 7
bit 0
bit 7-6
Unimplemented: Read as ‘0’
bit 5-4
DCxB1:DCxB0: PWM Duty Cycle bit 1 and bit 0 for CCP Module x
Capture mode:
Unused.
Compare mode:
Unused.
PWM mode:
These bits are the two LSbs (bit 1 and bit 0) of the 10-bit PWM duty cycle. The eight MSbs
(DCx9:DCx2) of the duty cycle are found in CCPRxL.
bit 3-0
CCPxM3:CCPxM0: CCP Module x Mode Select bits
0000 = Capture/Compare/PWM disabled (resets CCP module)
0001 = Reserved
0010 = Compare mode, toggle output on match (CCPIF bit is set)
0011 = Reserved
0100 = Capture mode, every falling edge
0101 = Capture mode, every rising edge
0110 = Capture mode, every 4th rising edge
0111 = Capture mode, every 16th rising edge
1000 = Compare mode: initialize CCP pin low; on compare match, force CCP pin high
(CCPIF bit is set)
1001 = Compare mode: initialize CCP pin high; on compare match, force CCP pin low
(CCPIF bit is set)
1010 = Compare mode: generate software interrupt on compare match (CCPIF bit is set,
CCP pin reflects I/O state)
1011 = Compare mode: trigger special event, reset timer, start A/D conversion on
CCP2 match (CCPxIF bit is set)
11xx = PWM mode
Legend:
R = Readable bit
-n = Value at POR
 2004 Microchip Technology Inc.
W = Writable bit
‘1’ = Bit is set
Preliminary
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
x = Bit is unknown
DS39636A-page 129
PIC18F2X1X/4X1X
14.1
CCP Module Configuration
Each Capture/Compare/PWM module is associated
with a control register (generically, CCPxCON) and a
data register (CCPRx). The data register, in turn, is
comprised of two 8-bit registers: CCPRxL (low byte)
and CCPRxH (high byte). All registers are both
readable and writable.
14.1.1
CCP MODULES AND TIMER
RESOURCES
14.1.2
The CCP modules utilize Timers 1, 2 or 3, depending
on the mode selected. Timer1 and Timer3 are available
to modules in Capture or Compare modes, while
Timer2 is available for modules in PWM mode.
TABLE 14-1:
CCP MODE – TIMER
RESOURCE
CCP/ECCP Mode
Timer Resource
Capture
Compare
PWM
Timer1 or Timer3
Timer1 or Timer3
Timer2
TABLE 14-2:
The assignment of a particular timer to a module is
determined by the Timer-to-CCP enable bits in the
T3CON register (Register 13-1). Both modules may be
active at any given time and may share the same timer
resource if they are configured to operate in the same
mode (Capture/Compare or PWM) at the same time. The
interactions between the two modules are summarized in
Figure 14-1 and Figure 14-2. In Timer1 in Asynchronous
Counter mode, the capture operation will not work.
CCP2 PIN ASSIGNMENT
The pin assignment for CCP2 (Capture input, Compare
and PWM output) can change, based on device configuration. The CCP2MX configuration bit determines
which pin CCP2 is multiplexed to. By default, it is
assigned to RC1 (CCP2MX = 1). If the configuration bit
is cleared, CCP2 is multiplexed with RB3.
Changing the pin assignment of CCP2 does not automatically change any requirements for configuring the
port pin. Users must always verify that the appropriate
TRIS register is configured correctly for CCP2
operation, regardless of where it is located.
INTERACTIONS BETWEEN CCP1 AND CCP2 FOR TIMER RESOURCES
CCP1 Mode CCP2 Mode
Interaction
Capture
Capture
Each module can use TMR1 or TMR3 as the time base. The time base can be different
for each CCP.
Capture
Compare
CCP2 can be configured for the special event trigger to reset TMR1 or TMR3
(depending upon which time base is used). Automatic A/D conversions on trigger event
can also be done. Operation of CCP1 could be affected if it is using the same timer as a
time base.
Compare
Capture
CCP1 can be configured for the special event trigger to reset TMR1 or TMR3 (depending
upon which time base is used). Operation of CCP2 could be affected if it is using the
same timer as a time base.
Compare
Compare
Either module can be configured for the Special Event Trigger to reset the time base.
Automatic A/D conversions on CCP2 trigger event can be done. Conflicts may occur if
both modules are using the same time base.
Capture
PWM(1)
None
Compare
PWM(1)
None
PWM(1)
Capture
None
Compare
None
(1)
PWM
PWM(1)
Note 1:
PWM
Both PWMs will have the same frequency and update rate (TMR2 interrupt).
Includes standard and Enhanced PWM operation.
DS39636A-page 130
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
14.2
14.2.3
Capture Mode
When the Capture mode is changed, a false capture
interrupt may be generated. The user should keep the
CCPxIE interrupt enable bit clear to avoid false interrupts. The interrupt flag bit, CCPxIF, should also be
cleared following any such change in operating mode.
In Capture mode, the CCPRxH:CCPRxL register pair
captures the 16-bit value of the TMR1 or TMR3
registers when an event occurs on the corresponding
CCPx pin. An event is defined as one of the following:
•
•
•
•
every falling edge
every rising edge
every 4th rising edge
every 16th rising edge
14.2.4
Switching from one capture prescaler to another may
generate an interrupt. Also, the prescaler counter will
not be cleared; therefore, the first capture may be from
a non-zero prescaler. Example 14-1 shows the
recommended method for switching between capture
prescalers. This example also clears the prescaler
counter and will not generate the “false” interrupt.
CCP PIN CONFIGURATION
In Capture mode, the appropriate CCPx pin should be
configured as an input by setting the corresponding
TRIS direction bit.
Note:
14.2.2
If RB3/CCP2 or RC1/CCP2 is configured
as an output, a write to the port can cause
a capture condition.
EXAMPLE 14-1:
TIMER1/TIMER3 MODE SELECTION
CLRF
MOVLW
The timers that are to be used with the capture feature
(Timer1 and/or Timer3) must be running in Timer mode or
Synchronized Counter mode. In Asynchronous Counter
mode, the capture operation will not work. The timer to be
used with each CCP module is selected in the T3CON
register (see Section 14.1.1 “CCP Modules and Timer
Resources”).
FIGURE 14-1:
CCP PRESCALER
There are four prescaler settings in Capture mode; they
are specified as part of the operating mode selected by
the mode select bits (CCPxM3:CCPxM0). Whenever
the CCP module is turned off or Capture mode is disabled, the prescaler counter is cleared. This means
that any Reset will clear the prescaler counter.
The event is selected by the mode select bits,
CCPxM3:CCPxM0 (CCPxCON<3:0>). When a capture
is made, the interrupt request flag bit, CCPxIF, is set; it
must be cleared in software. If another capture occurs
before the value in register CCPRx is read, the old
captured value is overwritten by the new captured value.
14.2.1
SOFTWARE INTERRUPT
MOVWF
CHANGING BETWEEN
CAPTURE PRESCALERS
(CCP2 SHOWN)
CCP2CON
; Turn CCP module off
NEW_CAPT_PS ; Load WREG with the
; new prescaler mode
; value and CCP ON
CCP2CON
; Load CCP2CON with
; this value
CAPTURE MODE OPERATION BLOCK DIAGRAM
TMR3H
TMR3L
Set CCP1IF
T3CCP2
CCP1 pin
Prescaler
÷ 1, 4, 16
and
Edge Detect
CCPR1H
T3CCP2
4
CCP1CON<3:0>
Q1:Q4
CCP2CON<3:0>
4
TMR3
Enable
CCPR1L
TMR1
Enable
TMR1H
TMR1L
TMR3H
TMR3L
Set CCP2IF
4
T3CCP1
T3CCP2
TMR3
Enable
CCP2 pin
Prescaler
÷ 1, 4, 16
and
Edge Detect
CCPR2H
CCPR2L
TMR1
Enable
T3CCP2
T3CCP1
 2004 Microchip Technology Inc.
Preliminary
TMR1H
TMR1L
DS39636A-page 131
PIC18F2X1X/4X1X
14.3
14.3.2
Compare Mode
TIMER1/TIMER3 MODE SELECTION
In Compare mode, the 16-bit CCPRx register value is
constantly compared against either the TMR1 or TMR3
register pair value. When a match occurs, the CCPx pin
can be:
Timer1 and/or Timer3 must be running in Timer mode
or Synchronized Counter mode if the CCP module is
using the compare feature. In Asynchronous Counter
mode, the compare operation may not work.
•
•
•
•
14.3.3
driven high
driven low
toggled (high-to-low or low-to-high)
remain unchanged (that is, reflects the state of the
I/O latch)
When the Generate Software Interrupt mode is chosen
(CCPxM3:CCPxM0 = 1010), the corresponding CCPx
pin is not affected. Only a CCP interrupt is generated,
if enabled and the CCPxIE bit is set.
The action on the pin is based on the value of the mode
select bits (CCPxM3:CCPxM0). At the same time, the
interrupt flag bit CCPxIF is set.
14.3.1
14.3.4
SPECIAL EVENT TRIGGER
Both CCP modules are equipped with a special event
trigger. This is an internal hardware signal generated
in Compare mode to trigger actions by other modules.
The special event trigger is enabled by selecting the
Compare
Special
Event
Trigger
mode
(CCPxM3:CCPxM0 = 1011).
CCP PIN CONFIGURATION
The user must configure the CCPx pin as an output by
clearing the appropriate TRIS bit.
Note:
SOFTWARE INTERRUPT MODE
Clearing the CCP2CON register will force
the RB3 or RC1 compare output latch
(depending on device configuration) to the
default low level. This is not the PORTB or
PORTC I/O data latch.
For either CCP module, the special event trigger resets
the timer register pair for whichever timer resource is
currently assigned as the module’s time base. This
allows the CCPRx registers to serve as a programmable period register for either timer.
The special event trigger for CCP2 can also start an A/D
conversion. In order to do this, the A/D converter must
already be enabled.
FIGURE 14-2:
COMPARE MODE OPERATION BLOCK DIAGRAM
CCPR1H
Set CCP1IF
CCPR1L
Special Event Trigger
(Timer1/Timer3 Reset)
CCP1 pin
Comparator
Output
Logic
Compare
Match
S
Q
R
TRIS
Output Enable
4
CCP1CON<3:0>
0
TMR1H
TMR1L
0
1
TMR3H
TMR3L
1
Special Event Trigger
(Timer1/Timer3 Reset, A/D Trigger)
T3CCP1
T3CCP2
Set CCP2IF
Comparator
CCPR2H
CCP2 pin
Compare
Match
Output
Logic
4
CCPR2L
S
Q
R
TRIS
Output Enable
CCP2CON<3:0>
DS39636A-page 132
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
TABLE 14-3:
Name
INTCON
REGISTERS ASSOCIATED WITH CAPTURE, COMPARE, TIMER1 AND TIMER3
Bit 7
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
Values
on page
TMR0IE
INT0IE
RBIE
TMR0IF
INT0IF
RBIF
49
Bit 6
GIE/GIEH PEIE/GIEL
(2)
—
RI
TO
PD
POR
BOR
48
PIR1
PSPIF(1)
ADIF
RCIF
TXIF
SSPIF
CCP1IF
TMR2IF
TMR1IF
52
PIE1
(1)
PSPIE
ADIE
RCIE
TXIE
SSPIE
CCP1IE
TMR2IE
TMR1IE
52
IPR1
PSPIP(1)
ADIP
RCIP
TXIP
SSPIP
CCP1IP
TMR2IP
TMR1IP
52
RCON
IPEN
SBOREN
PIR2
OSCFIF
CMIF
—
—
BCLIF
HLVDIF
TMR3IF
CCP2IF
52
PIE2
OSCFIE
CMIE
—
—
BCLIE
HLVDIE
TMR3IE
CCP2IE
52
OSCFIP
CMIP
—
—
BCLIP
HLVDIP
TMR3IP
CCP2IP
52
IPR2
TRISB
PORTB Data Direction Control Register
52
TRISC
PORTC Data Direction Control Register
52
TMR1L
Timer1 Register Low Byte
50
TMR1H
Timer1 Register High Byte
T1CON
RD16
T1RUN
T1CKPS1 T1CKPS0 T1OSCEN T1SYNC
TMR3H
Timer3 Register High Byte
TMR3L
Timer3 Register Low Byte
T3CON
RD16
T3CCP2
50
TMR1CS TMR1ON
50
51
51
T3CKPS1 T3CKPS0
T3CCP1
T3SYNC
TMR3CS TMR3ON
51
CCPR1L
Capture/Compare/PWM Register 1 Low Byte
51
CCPR1H
Capture/Compare/PWM Register 1 High Byte
51
CCP1CON
P1M1(1)
P1M0(1)
DC1B1
DC1B0
CCPR2L
Capture/Compare/PWM Register 2 Low Byte
CCPR2H
Capture/Compare/PWM Register 2 High Byte
CCP2CON
—
—
DC2B1
DC2B0
CCP1M3
CCP1M2
CCP1M1
CCP1M0
51
51
51
CCP2M3
CCP2M2
CCP2M1
CCP2M0
51
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used by Capture/Compare, Timer1 or Timer3.
Note 1: These bits are unimplemented on 28-pin devices and read as ‘0’.
2: The SBOREN bit is only available when the BOREN1:BOREN0 configuration bits = 01; otherwise, it is
disabled and reads as ‘0’. See Section 4.4 “Brown-out Reset (BOR)”.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 133
PIC18F2X1X/4X1X
14.4
14.4.1
PWM Mode
In Pulse-Width Modulation (PWM) mode, the CCPx pin
produces up to a 10-bit resolution PWM output. Since
the CCP2 pin is multiplexed with a PORTB or PORTC
data latch, the appropriate TRIS bit must be cleared to
make the CCP2 pin an output.
Note:
Clearing the CCP2CON register will force
the RB3 or RC1 output latch (depending
on device configuration) to the default
low level. This is not the PORTB or
PORTC I/O data latch.
Figure 14-3 shows a simplified block diagram of the
CCP module in PWM mode.
For a step-by-step procedure on how to set up the CCP
module for PWM operation, see Section 14.4.4
“Setup for PWM Operation”.
FIGURE 14-3:
SIMPLIFIED PWM BLOCK
DIAGRAM
The PWM period is specified by writing to the PR2
register. The PWM period can be calculated using the
following formula:
EQUATION 14-1:
PWM Period = [(PR2) + 1] • 4 • TOSC •
(TMR2 Prescale Value)
PWM frequency is defined as 1/[PWM period].
When TMR2 is equal to PR2, the following three events
occur on the next increment cycle:
• TMR2 is cleared
• The CCPx pin is set (exception: if PWM duty
cycle = 0%, the CCPx pin will not be set)
• The PWM duty cycle is latched from CCPRxL into
CCPRxH
Note:
CCPxCON<5:4>
Duty Cycle Registers
CCPRxL
14.4.2
CCPRxH (Slave)
CCPx Output
R
Comparator
TMR2
Q
(Note 1)
S
Comparator
Clear Timer,
CCP1 pin and
latch D.C.
PR2
Corresponding
TRIS bit
The Timer2 postscalers (see Section 12.0
“Timer2 Module”) are not used in the
determination of the PWM frequency. The
postscaler could be used to have a servo
update rate at a different frequency than
the PWM output.
PWM DUTY CYCLE
The PWM duty cycle is specified by writing to the
CCPRxL register and to the CCPxCON<5:4> bits. Up
to 10-bit resolution is available. The CCPRxL contains
the eight MSbs and the CCPxCON<5:4> contains the
two LSbs. This 10-bit value is represented by
CCPRxL:CCPxCON<5:4>. The following equation is
used to calculate the PWM duty cycle in time:
EQUATION 14-2:
Note 1: The 8-bit TMR2 value is concatenated with 2-bit
internal Q clock, or 2 bits of the prescaler, to create the
10-bit time base.
A PWM output (Figure 14-4) has a time base (period)
and a time that the output stays high (duty cycle).
The frequency of the PWM is the inverse of the
period (1/period).
FIGURE 14-4:
PWM PERIOD
PWM Duty Cycle = (CCPRXL:CCPXCON<5:4>) •
TOSC • (TMR2 Prescale Value)
CCPRxL and CCPxCON<5:4> can be written to at any
time but the duty cycle value is not latched into
CCPR2H until after a match between PR2 and TMR2
occurs (i.e., the period is complete). In PWM mode,
CCPRxH is a read-only register.
PWM OUTPUT
Period
Duty Cycle
TMR2 = PR2
TMR2 = Duty Cycle
TMR2 = PR2
DS39636A-page 134
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
The CCPRxH register and a 2-bit internal latch are
used to double-buffer the PWM duty cycle. This
double-buffering is essential for glitchless PWM
operation.
EQUATION 14-3:
F OSC
log  ---------------
 F PWM
PWM Resolution (max) = -----------------------------bits
log ( 2 )
When the CCPRxH and 2-bit latch match TMR2,
concatenated with an internal 2-bit Q clock or 2 bits of
the TMR2 prescaler, the CCPx pin is cleared.
Note:
The maximum PWM resolution (bits) for a given PWM
frequency is given by the equation:
TABLE 14-4:
EXAMPLE PWM FREQUENCIES AND RESOLUTIONS AT 40 MHz
PWM Frequency
Timer Prescaler (1, 4, 16)
PR2 Value
Maximum Resolution (bits)
14.4.3
If the PWM duty cycle value is longer than
the PWM period, the CCP2 pin will not be
cleared.
2.44 kHz
9.77 kHz
39.06 kHz
156.25 kHz
312.50 kHz
416.67 kHz
16
4
1
1
1
1
FFh
FFh
FFh
3Fh
1Fh
17h
10
10
10
8
7
6.58
14.4.4
PWM AUTO-SHUTDOWN
(CCP1 ONLY)
The PWM auto-shutdown features of the Enhanced
CCP module are also available to CCP1 in 28-pin
devices. The operation of this feature is
discussed in detail in Section 15.4.7 “Enhanced
PWM Auto-Shutdown”.
Auto-shutdown features are not available for CCP2.
The following steps should be taken when configuring
the CCP module for PWM operation:
1.
2.
3.
4.
5.
 2004 Microchip Technology Inc.
SETUP FOR PWM OPERATION
Preliminary
Set the PWM period by writing to the PR2
register.
Set the PWM duty cycle by writing to the
CCPRxL register and CCPxCON<5:4> bits.
Make the CCPx pin an output by clearing the
appropriate TRIS bit.
Set the TMR2 prescale value, then enable
Timer2 by writing to T2CON.
Configure the CCPx module for PWM operation.
DS39636A-page 135
PIC18F2X1X/4X1X
TABLE 14-5:
Name
INTCON
REGISTERS ASSOCIATED WITH PWM AND TIMER2
Bit 7
Bit 6
GIE/GIEH PEIE/GIEL
(2)
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
Values
on page
TMR0IE
INT0IE
RBIE
TMR0IF
INT0IF
RBIF
49
—
RI
TO
PD
POR
BOR
48
PIR1
PSPIF(1)
ADIF
RCIF
TXIF
SSPIF
CCP1IF
TMR2IF
TMR1IF
52
PIE1
PSPIE(1)
ADIE
RCIE
TXIE
SSPIE
CCP1IE
TMR2IE
TMR1IE
52
IPR1
PSPIP(1)
ADIP
RCIP
TXIP
SSPIP
CCP1IP
TMR2IP
TMR1IP
52
RCON
IPEN
SBOREN
Bit 5
TRISB
PORTB Data Direction Control Register
52
TRISC
PORTC Data Direction Control Register
52
TMR2
Timer2 Register
50
PR2
Timer2 Period Register
50
T2CON
—
T2OUTPS3 T2OUTPS2 T2OUTPS1 T2OUTPS0 TMR2ON T2CKPS1 T2CKPS0
CCPR1L
Capture/Compare/PWM Register 1 Low Byte
CCPR1H
Capture/Compare/PWM Register 1 High Byte
CCP1CON
P1M1(1)
P1M0(1)
DC1B1
DC1B0
50
51
51
CCP1M3
CCP1M2
CCP1M1
CCP1M0
51
CCPR2L
Capture/Compare/PWM Register 2 Low Byte
51
CCPR2H
Capture/Compare/PWM Register 2 High Byte
51
CCP2CON
ECCP1AS
PWM1CON
—
—
ECCPASE ECCPAS2
PRSEN
PDC6(1)
DC2B1
DC2B0
CCP2M3
CCP2M2
ECCPAS1
ECCPAS0
PSSAC1
PSSAC0 PSSBD1(1) PSSBD0(1)
CCP2M1
51
PDC5(1)
PDC4(1)
PDC3(1)
PDC2(1)
51
PDC1(1)
CCP2M0
PDC0(1)
51
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used by PWM or Timer2.
Note 1: These bits are unimplemented on 28-pin devices and read as ‘0’.
2: The SBOREN bit is only available when the BOREN1:BOREN0 configuration bits = 01; otherwise, it is
disabled and reads as ‘0’. See Section 4.4 “Brown-out Reset (BOR)”.
DS39636A-page 136
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
15.0
Note:
ENHANCED CAPTURE/
COMPARE/PWM (ECCP)
MODULE
and restart. The Enhanced features are discussed in
detail in Section 15.4 “Enhanced PWM Mode”.
Capture, Compare and single-output PWM functions of
the ECCP module are the same as described for the
standard CCP module.
The ECCP module is implemented only in
40/44-pin devices.
The control register for the Enhanced CCP module is
shown in Register 15-1. It differs from the CCPxCON
registers in PIC18F2410/2510/2515/2610 devices in
that the two Most Significant bits are implemented to
control PWM functionality.
In PIC18F4410/4510/4515/4610 devices, CCP1 is
implemented as a standard CCP module with
enhanced PWM capabilities. These include the
provision for 2 or 4 output channels, user selectable
polarity, dead-band control and automatic shutdown
REGISTER 15-1:
CCP1CON REGISTER (ECCP1 MODULE, 40/44-PIN DEVICES)
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
P1M1
P1M0
DC1B1
DC1B0
CCP1M3
CCP1M2
CCP1M1
CCP1M0
bit 7
bit 0
bit 7-6
P1M1:P1M0: Enhanced PWM Output Configuration bits
If CCP1M3:CCP1M2 = 00, 01, 10:
xx = P1A assigned as Capture/Compare input/output; P1B, P1C, P1D assigned as port pins
If CCP1M3:CCP1M2 = 11:
00 = Single output: P1A modulated; P1B, P1C, P1D assigned as port pins
01 = Full-bridge output forward: P1D modulated; P1A active; P1B, P1C inactive
10 = Half-bridge output: P1A, P1B modulated with dead-band control; P1C, P1D assigned
as port pins
11 = Full-bridge output reverse: P1B modulated; P1C active; P1A, P1D inactive
bit 5-4
DC1B1:DC1B0: PWM Duty Cycle bit 1 and bit 0
Capture mode:
Unused.
Compare mode:
Unused.
PWM mode:
These bits are the two LSbs of the 10-bit PWM duty cycle. The eight MSbs of the duty cycle are
found in CCPR1L.
bit 3-0
CCP1M3:CCP1M0: Enhanced CCP Mode Select bits
0000 = Capture/Compare/PWM off (resets ECCP module)
0001 = Reserved
0010 = Compare mode, toggle output on match
0011 = Capture mode
0100 = Capture mode, every falling edge
0101 = Capture mode, every rising edge
0110 = Capture mode, every 4th rising edge
0111 = Capture mode, every 16th rising edge
1000 = Compare mode, initialize CCP1 pin low, set output on compare match (set CCP1IF)
1001 = Compare mode, initialize CCP1 pin high, clear output on compare match (set CCP1IF)
1010 = Compare mode, generate software interrupt only, CCP1 pin reverts to I/O state
1011 = Compare mode, trigger special event (ECCP resets TMR1 or TMR3, sets CC1IF bit)
1100 = PWM mode; P1A, P1C active-high; P1B, P1D active-high
1101 = PWM mode; P1A, P1C active-high; P1B, P1D active-low
1110 = PWM mode; P1A, P1C active-low; P1B, P1D active-high
1111 = PWM mode; P1A, P1C active-low; P1B, P1D active-low
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
 2004 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS39636A-page 137
PIC18F2X1X/4X1X
In addition to the expanded range of modes available
through the CCP1CON and ECCP1AS registers, the
ECCP module has an additional register associated
with Enhanced PWM operation and auto-shutdown
features. This register is:
• PWM1CON (PWM Configuration register)
15.1
ECCP Outputs and Configuration
The Enhanced CCP module may have up to four PWM
outputs, depending on the selected operating mode.
These outputs, designated P1A through P1D, are
multiplexed with I/O pins on PORTC and PORTD. The
outputs that are active depend on the CCP operating
mode selected. The pin assignments are summarized
in Table 15-1.
To configure the I/O pins as PWM outputs, the proper
PWM mode must be selected by setting the
P1M1:P1M0 and CCP1M3:CCP1M0 bits. The
appropriate TRISC and TRISD direction bits for the port
pins must also be set as outputs.
15.1.1
ECCP MODULES AND TIMER
RESOURCES
Like the standard CCP modules, the ECCP module can
utilize Timers 1, 2 or 3, depending on the mode
selected. Timer1 and Timer3 are available for modules
in Capture or Compare modes, while Timer2 is
available for modules in PWM mode. Interactions
between the standard and Enhanced CCP modules are
identical to those described for standard CCP modules.
Additional details on timer resources are provided in
Section 14.1.1
“CCP
Modules
and
Timer
Resources”.
TABLE 15-1:
15.2
Capture and Compare Modes
Except for the operation of the special event trigger
discussed below, the Capture and Compare modes of
the ECCP module are identical in operation to that of
CCP2. These are discussed in detail in Section 14.2
“Capture Mode” and Section 14.3 “Compare
Mode”. No changes are required when moving
between 28-pin and 40/44-pin devices.
15.2.1
SPECIAL EVENT TRIGGER
The special event trigger output of ECCP1 resets the
TMR1 or TMR3 register pair, depending on which timer
resource is currently selected. This allows the CCPR1
register to effectively be a 16-bit programmable period
register for Timer1 or Timer3.
15.3
Standard PWM Mode
When configured in Single Output mode, the ECCP
module functions identically to the standard CCP
module in PWM mode, as described in Section 14.4
“PWM Mode”. This is also sometimes referred to as
“Compatible CCP” mode, as in Table 15-1.
Note:
When setting up single output PWM
operations, users are free to use either of
the processes described in Section 14.4.4
“Setup for PWM Operation” or
Section 15.4.9 “Setup for PWM Operation”. The latter is more generic and will
work for either single or multi-output PWM.
PIN ASSIGNMENTS FOR VARIOUS ECCP1 MODES
ECCP Mode
CCP1CON
Configuration
RC2
RD5
RD6
RD7
All 40/44-pin devices:
Compatible CCP
00xx 11xx
CCP1
RD5/PSP5
RD6/PSP6
RD7/PSP7
Dual PWM
10xx 11xx
P1A
P1B
RD6/PSP6
RD7/PSP7
Quad PWM
x1xx 11xx
P1A
P1B
P1C
P1D
Legend: x = Don’t care. Shaded cells indicate pin assignments not used by ECCP1 in a given mode.
DS39636A-page 138
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
15.4
15.4.1
Enhanced PWM Mode
The Enhanced PWM mode provides additional PWM
output options for a broader range of control applications. The module is a backward compatible version of
the standard CCP module and offers up to four outputs,
designated P1A through P1D. Users are also able to
select the polarity of the signal (either active-high or
active-low). The module’s output mode and polarity are
configured by setting the P1M1:P1M0 and
CCP1M3:CCP1M0 bits of the CCP1CON register.
Figure 15-1 shows a simplified block diagram of PWM
operation. All control registers are double-buffered and
are loaded at the beginning of a new PWM cycle (the
period boundary when Timer2 resets) in order to
prevent glitches on any of the outputs. The exception is
the PWM Delay register, PWM1CON, which is loaded
at either the duty cycle boundary or the period boundary (whichever comes first). Because of the buffering,
the module waits until the assigned timer resets instead
of starting immediately. This means that Enhanced
PWM waveforms do not exactly match the standard
PWM waveforms, but are instead offset by one full
instruction cycle (4 TOSC).
PWM PERIOD
The PWM period is specified by writing to the PR2
register. The PWM period can be calculated using the
following equation.
EQUATION 15-1:
PWM Period = [(PR2) + 1] • 4 • TOSC •
(TMR2 Prescale Value)
PWM frequency is defined as 1/[PWM period]. When
TMR2 is equal to PR2, the following three events occur
on the next increment cycle:
• TMR2 is cleared
• The CCP1 pin is set (if PWM duty cycle = 0%, the
CCP1 pin will not be set)
• The PWM duty cycle is copied from CCPR1L into
CCPR1H
Note:
As before, the user must manually configure the
appropriate TRIS bits for output.
FIGURE 15-1:
The Timer2 postscaler (see Section 12.0
“Timer2 Module”) is not used in the
determination of the PWM frequency. The
postscaler could be used to have a servo
update rate at a different frequency than
the PWM output.
SIMPLIFIED BLOCK DIAGRAM OF THE ENHANCED PWM MODULE
CCP1CON<5:4>
Duty Cycle Registers
CCP1M<3:0>
4
P1M1<1:0>
2
CCPR1L
CCP1/P1A
CCP1/P1A
TRISx<x>
CCPR1H (Slave)
P1B
R
Comparator
Q
Output
Controller
P1B
TRISx<x>
P1C
TMR2
(Note 1)
P1D
Comparator
PR2
P1C
TRISx<x>
S
Clear Timer,
set CCP1 pin and
latch D.C.
P1D
TRISx<x>
PWM1CON
Note: The 8-bit TMR2 register is concatenated with the 2-bit internal Q clock, or 2 bits of the prescaler, to create the 10-bit time
base.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 139
PIC18F2X1X/4X1X
15.4.2
PWM DUTY CYCLE
EQUATION 15-3:
The PWM duty cycle is specified by writing to the
CCPR1L register and to the CCP1CON<5:4> bits. Up
to 10-bit resolution is available. The CCPR1L contains
the eight MSbs and the CCP1CON<5:4> contains the
two LSbs. This 10-bit value is represented by
CCPR1L:CCP1CON<5:4>. The PWM duty cycle is
calculated by the following equation.
log FOSC
FPWM
PWM Resolution (max) =
log(2)
(
Note:
EQUATION 15-2:
PWM Duty Cycle = (CCPR1L:CCP1CON<5:4>) •
TOSC • (TMR2 Prescale Value)
15.4.3
CCPR1L and CCP1CON<5:4> can be written to at any
time, but the duty cycle value is not copied into
CCPR1H until a match between PR2 and TMR2 occurs
(i.e., the period is complete). In PWM mode, CCPR1H
is a read-only register.
The CCPR1H register and a 2-bit internal latch are
used to double-buffer the PWM duty cycle. This
double-buffering is essential for glitchless PWM
operation. When the CCPR1H and 2-bit latch match
TMR2, concatenated with an internal 2-bit Q clock or
two bits of the TMR2 prescaler, the CCP1 pin is
cleared. The maximum PWM resolution (bits) for a
given PWM frequency is given by the following
equation.
TABLE 15-2:
) bits
If the PWM duty cycle value is longer than
the PWM period, the CCP1 pin will not be
cleared.
PWM OUTPUT CONFIGURATIONS
The P1M1:P1M0 bits in the CCP1CON register allow
one of four configurations:
•
•
•
•
Single Output
Half-Bridge Output
Full-Bridge Output, Forward mode
Full-Bridge Output, Reverse mode
The Single Output mode is the standard PWM mode
discussed in Section 15.4 “Enhanced PWM Mode”.
The Half-Bridge and Full-Bridge Output modes are
covered in detail in the sections that follow.
The general relationship of the outputs in all
configurations is summarized in Figure 15-2.
EXAMPLE PWM FREQUENCIES AND RESOLUTIONS AT 40 MHz
PWM Frequency
Timer Prescaler (1, 4, 16)
PR2 Value
Maximum Resolution (bits)
DS39636A-page 140
2.44 kHz
9.77 kHz
39.06 kHz
156.25 kHz
312.50 kHz
416.67 kHz
16
4
1
1
1
1
FFh
FFh
FFh
3Fh
1Fh
17h
10
10
10
8
7
6.58
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
FIGURE 15-2:
PWM OUTPUT RELATIONSHIPS (ACTIVE-HIGH STATE)
0
CCP1CON
<7:6>
00
(Single Output)
PR2 + 1
Duty
Cycle
SIGNAL
Period
P1A Modulated
Delay(1)
Delay(1)
P1A Modulated
10
(Half-Bridge)
P1B Modulated
P1A Active
01
(Full-Bridge,
Forward)
P1B Inactive
P1C Inactive
P1D Modulated
P1A Inactive
11
(Full-Bridge,
Reverse)
P1B Modulated
P1C Active
P1D Inactive
FIGURE 15-3:
PWM OUTPUT RELATIONSHIPS (ACTIVE-LOW STATE)
0
CCP1CON
<7:6>
00
(Single Output)
PR2 + 1
Duty
Cycle
SIGNAL
Period
P1A Modulated
P1A Modulated
10
(Half-Bridge)
Delay(1)
Delay(1)
P1B Modulated
P1A Active
01
(Full-Bridge,
Forward)
P1B Inactive
P1C Inactive
P1D Modulated
P1A Inactive
11
(Full-Bridge,
Reverse)
P1B Modulated
P1C Active
P1D Inactive
Relationships:
• Period = 4 * TOSC * (PR2 + 1) * (TMR2 Prescale Value)
• Duty Cycle = TOSC * (CCPR1L<7:0>:CCP1CON<5:4>) * (TMR2 Prescale Value)
• Delay = 4 * TOSC * (ECCPDEL<6:0>)
Note 1: Dead-band delay is programmed using the PWM1CON register (Section 15.4.6 “Programmable
Dead-Band Delay”).
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 141
PIC18F2X1X/4X1X
15.4.4
HALF-BRIDGE MODE
FIGURE 15-4:
In the Half-Bridge Output mode, two pins are used as
outputs to drive push-pull loads. The PWM output
signal is output on the P1A pin, while the complementary PWM output signal is output on the P1B pin
(Figure 15-4). This mode can be used for half-bridge
applications, as shown in Figure 15-5, or for full-bridge
applications where four power switches are being
modulated with two PWM signals.
HALF-BRIDGE PWM
OUTPUT
Period
Period
Duty Cycle
P1A(2)
td
td
P1B(2)
In Half-Bridge Output mode, the programmable deadband delay can be used to prevent shoot-through
current in half-bridge power devices. The value of bits
PDC6:PDC0 sets the number of instruction cycles
before the output is driven active. If the value is greater
than the duty cycle, the corresponding output remains
inactive during the entire cycle. See Section 15.4.6
“Programmable Dead-Band Delay” for more details
of the dead-band delay operations.
(1)
(1)
(1)
td = Dead-Band Delay
Note 1: At this time, the TMR2 register is equal to the
PR2 register.
2: Output signals are shown as active-high.
Since the P1A and P1B outputs are multiplexed with
the PORTC<2> and PORTD<5> data latches, the
TRISC<2> and TRISD<5> bits must be cleared to
configure P1A and P1B as outputs.
FIGURE 15-5:
EXAMPLES OF HALF-BRIDGE OUTPUT MODE APPLICATIONS
V+
Standard Half-Bridge Circuit (“Push-Pull”)
PIC18F4X1X
FET
Driver
+
V
-
P1A
Load
FET
Driver
+
V
-
P1B
V-
Half-Bridge Output Driving a Full-Bridge Circuit
V+
PIC18F4X1X
FET
Driver
FET
Driver
P1A
FET
Driver
Load
FET
Driver
P1B
V-
DS39636A-page 142
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
15.4.5
FULL-BRIDGE MODE
In Full-Bridge Output mode, four pins are used as
outputs; however, only two outputs are active at a time.
In the Forward mode, pin P1A is continuously active
and pin P1D is modulated. In the Reverse mode, pin
P1C is continuously active and pin P1B is modulated.
These are illustrated in Figure 15-6.
FIGURE 15-6:
P1A, P1B, P1C and P1D outputs are multiplexed with
the PORTC<2> and PORTD<7:5> data latches. The
TRISC<2> and TRISD<7:5> bits must be cleared to
make the P1A, P1B, P1C and P1D pins outputs.
FULL-BRIDGE PWM OUTPUT
Forward Mode
Period
P1A
(2)
Duty Cycle
P1B(2)
P1C(2)
P1D(2)
(1)
(1)
Reverse Mode
Period
Duty Cycle
P1A(2)
P1B(2)
P1C(2)
P1D(2)
(1)
(1)
Note 1: At this time, the TMR2 register is equal to the PR2 register.
Note 2: Output signal is shown as active-high.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 143
PIC18F2X1X/4X1X
FIGURE 15-7:
EXAMPLE OF FULL-BRIDGE APPLICATION
V+
PIC18F4X1X
FET
Driver
QC
QA
FET
Driver
P1A
Load
P1B
FET
Driver
P1C
FET
Driver
QD
QB
VP1D
15.4.5.1
Direction Change in Full-Bridge Mode
In the Full-Bridge Output mode, the P1M1 bit in the
CCP1CON register allows user to control the forward/
reverse direction. When the application firmware
changes this direction control bit, the module will
assume the new direction on the next PWM cycle.
Just before the end of the current PWM period, the
modulated outputs (P1B and P1D) are placed in their
inactive state, while the unmodulated outputs (P1A and
P1C) are switched to drive in the opposite direction.
This occurs in a time interval of 4 TOSC * (Timer2
Prescale Value) before the next PWM period begins.
The Timer2 prescaler will be either 1, 4 or 16, depending on the value of the T2CKPS bit (T2CON<1:0>).
During the interval from the switch of the unmodulated
outputs to the beginning of the next period, the
modulated outputs (P1B and P1D) remain inactive.
This relationship is shown in Figure 15-8.
Note that in the Full-Bridge Output mode, the CCP1
module does not provide any dead-band delay. In
general, since only one output is modulated at all times,
dead-band delay is not required. However, there is a
situation where a dead-band delay might be required.
This situation occurs when both of the following
conditions are true:
1.
2.
Figure 15-9 shows an example where the PWM
direction changes from forward to reverse at a near
100% duty cycle. At time t1, the outputs P1A and P1D
become inactive, while output P1C becomes active. In
this example, since the turn-off time of the power
devices is longer than the turn-on time, a shoot-through
current may flow through power devices, QC and QD
(see Figure 15-7), for the duration of ‘t’. The same
phenomenon will occur to power devices, QA and QB,
for PWM direction change from reverse to forward.
If changing PWM direction at high duty cycle is required
for an application, one of the following requirements
must be met:
1.
2.
Reduce PWM for a PWM period before
changing directions.
Use switch drivers that can drive the switches off
faster than they can drive them on.
Other options to prevent shoot-through current may
exist.
The direction of the PWM output changes when
the duty cycle of the output is at or near 100%.
The turn-off time of the power switch, including
the power device and driver circuit, is greater
than the turn-on time.
DS39636A-page 144
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
FIGURE 15-8:
PWM DIRECTION CHANGE
Period(1)
SIGNAL
Period
P1A (Active-High)
P1B (Active-High)
DC
P1C (Active-High)
(Note 2)
P1D (Active-High)
DC
Note 1: The direction bit in the CCP1 Control register (CCP1CON<7>) is written any time during the PWM cycle.
2: When changing directions, the P1A and P1C signals switch before the end of the current PWM cycle at intervals
of 4 TOSC, 16 TOSC or 64 TOSC, depending on the Timer2 prescaler value. The modulated P1B and P1D signals
are inactive at this time.
FIGURE 15-9:
PWM DIRECTION CHANGE AT NEAR 100% DUTY CYCLE
Forward Period
t1
Reverse Period
P1A(1)
P1B(1)
DC
P1C(1)
P1D(1)
DC
tON(2)
External Switch C(1)
tOFF(3)
External Switch D(1)
t = tOFF – tON(2,3)
Potential
Shoot-Through
Current(1)
Note 1: All signals are shown as active-high.
2: tON is the turn-on delay of power switch QC and its driver.
3: tOFF is the turn-off delay of power switch QD and its driver.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 145
PIC18F2X1X/4X1X
15.4.6
Note:
PROGRAMMABLE DEAD-BAND
DELAY
Programmable dead-band delay is not
implemented in 28-pin devices with
standard CCP modules.
In half-bridge applications where all power switches are
modulated at the PWM frequency at all times, the
power switches normally require more time to turn off
than to turn on. If both the upper and lower power
switches are switched at the same time (one turned on
and the other turned off), both switches may be on for
a short period of time until one switch completely turns
off. During this brief interval, a very high current (shootthrough current) may flow through both power
switches, shorting the bridge supply. To avoid this
potentially destructive shoot-through current from
flowing during switching, turning on either of the power
switches is normally delayed to allow the other switch
to completely turn off.
In the Half-Bridge Output mode, a digitally programmable dead-band delay is available to avoid shootthrough current from destroying the bridge power
switches. The delay occurs at the signal transition from
the non-active state to the active state. See Figure 15-4
for illustration. Bits PDC6:PDC0 of the PWM1CON
register (Register 15-2) set the delay period in terms of
microcontroller instruction cycles (TCY or 4 TOSC).
These bits are not available on 28-pin devices as the
standard CCP module does not support half-bridge
operation.
15.4.7
ENHANCED PWM AUTO-SHUTDOWN
When the CCP1 is programmed for any of the Enhanced
PWM modes, the active output pins may be configured
for auto-shutdown. Auto-shutdown immediately places
the Enhanced PWM output pins into a defined shutdown
state when a shutdown event occurs.
REGISTER 15-2:
A shutdown event can be caused by either of the
comparator modules, a low level on the Fault input pin
(FLT0) or any combination of these three sources. The
comparators may be used to monitor a voltage input
proportional to a current being monitored in the bridge
circuit. If the voltage exceeds a threshold, the
comparator switches state and triggers a shutdown.
Alternatively, a low digital signal on FLT0 can also trigger
a shutdown. The auto-shutdown feature can be disabled
by not selecting any auto-shutdown sources. The autoshutdown sources to be used are selected using the
ECCPAS2:ECCPAS0 bits (bits<6:4> of the ECCP1AS
register).
When a shutdown occurs, the output pins are
asynchronously placed in their shutdown states,
specified
by
the
PSSAC1:PSSAC0
and
PSSBD1:PSSBD0 bits (ECCPAS3:ECCPAS0). Each
pin pair (P1A/P1C and P1B/P1D) may be set to drive
high, drive low or be tri-stated (not driving). The
ECCPASE bit (ECCPAS<7>) is also set to hold the
Enhanced PWM outputs in their shutdown states.
The ECCPASE bit is set by hardware when a shutdown
event occurs. If automatic restarts are not enabled, the
ECCPASE bit is cleared by firmware when the cause of
the shutdown clears. If automatic restarts are enabled,
the ECCPASE bit is automatically cleared when the
cause of the auto-shutdown has cleared.
If the ECCPASE bit is set when a PWM period begins,
the PWM outputs remain in their shutdown state for that
entire PWM period. When the ECCPASE bit is cleared,
the PWM outputs will return to normal operation at the
beginning of the next PWM period.
Note:
Writing to the ECCPASE bit is disabled
while a shutdown condition is active.
PWM1CON: PWM CONFIGURATION REGISTER
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
PRSEN
PDC6(1)
PDC5(1)
PDC4(1)
PDC3(1)
PDC2(1)
PDC1(1)
PDC0(1)
bit 7
bit 7
bit 6-0
bit 0
PRSEN: PWM Restart Enable bit
1 = Upon auto-shutdown, the ECCPASE bit clears automatically once the shutdown event
goes away; the PWM restarts automatically
0 = Upon auto-shutdown, ECCPASE must be cleared in software to restart the PWM
PDC6:PDC0: PWM Delay Count bits(1)
Delay time, in number of FOSC/4 (4 * TOSC) cycles, between the scheduled and actual time for
a PWM signal to transition to active.
Note 1: Unimplemented on 28-pin devices and read as ‘0’.
Legend:
R = Readable bit
-n = Value at POR
DS39636A-page 146
W = Writable bit
‘1’ = Bit is set
Preliminary
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
x = Bit is unknown
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
REGISTER 15-3:
ECCP1AS: ENHANCED CAPTURE/COMPARE/PWM AUTO-SHUTDOWN
CONTROL REGISTER
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
ECCPASE ECCPAS2 ECCPAS1 ECCPAS0 PSSAC1 PSSAC0 PSSBD1(1) PSSBD0(1)
bit 7
bit 0
bit 7
ECCPASE: ECCP Auto-Shutdown Event Status bit
1 = A shutdown event has occurred; ECCP outputs are in shutdown state
0 = ECCP outputs are operating
bit 6-4
ECCPAS2:ECCPAS0: ECCP Auto-Shutdown Source Select bits
111 = FLT0 or Comparator 1 or Comparator 2
110 = FLT0 or Comparator 2
101 = FLT0 or Comparator 1
100 = FLT0
011 = Either Comparator 1 or 2
010 = Comparator 2 output
001 = Comparator 1 output
000 = Auto-shutdown is disabled
bit 3-2
PSSAC1:PSSAC0: Pins A and C Shutdown State Control bits
1x = Pins A and C are tri-state (40/44-pin devices);
PWM output is tri-state (28-pin devices)
01 = Drive Pins A and C to ‘1’
00 = Drive Pins A and C to ‘0’
bit 1-0
PSSBD1:PSSBD0: Pins B and D Shutdown State Control bits(1)
1x = Pins B and D tri-state
01 = Drive Pins B and D to ‘1’
00 = Drive Pins B and D to ‘0’
Note 1: Unimplemented on 28-pin devices and read as ‘0’.
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
 2004 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS39636A-page 147
PIC18F2X1X/4X1X
15.4.7.1
Auto-Shutdown and
Automatic Restart
15.4.8
The auto-shutdown feature can be configured to allow
automatic restarts of the module following a shutdown
event. This is enabled by setting the PRSEN bit of the
PWM1CON register (PWM1CON<7>).
In Shutdown mode with PRSEN = 1 (Figure 15-10), the
ECCPASE bit will remain set for as long as the cause
of the shutdown continues. When the shutdown condition clears, the ECCP1ASE bit is cleared. If PRSEN = 0
(Figure 15-11), once a shutdown condition occurs, the
ECCPASE bit will remain set until it is cleared by firmware. Once ECCPASE is cleared, the Enhanced PWM
will resume at the beginning of the next PWM period.
Note:
Writing to the ECCPASE bit is disabled
while a shutdown condition is active.
Independent of the PRSEN bit setting, if the autoshutdown source is one of the comparators, the
shutdown condition is a level. The ECCPASE bit
cannot be cleared as long as the cause of the shutdown
persists.
The Auto-Shutdown mode can be forced by writing a ‘1’
to the ECCPASE bit.
FIGURE 15-10:
START-UP CONSIDERATIONS
When the ECCP module is used in the PWM mode, the
application hardware must use the proper external pullup and/or pull-down resistors on the PWM output pins.
When the microcontroller is released from Reset, all of
the I/O pins are in the high-impedance state. The external
circuits must keep the power switch devices in the off
state until the microcontroller drives the I/O pins with the
proper signal levels, or activates the PWM output(s).
The CCP1M1:CCP1M0 bits (CCP1CON<1:0>) allow
the user to choose whether the PWM output signals are
active-high or active-low for each pair of PWM output
pins (P1A/P1C and P1B/P1D). The PWM output
polarities must be selected before the PWM pins are
configured as outputs. Changing the polarity configuration while the PWM pins are configured as outputs is
not recommended, since it may result in damage to the
application circuits.
The P1A, P1B, P1C and P1D output latches may not be
in the proper states when the PWM module is initialized.
Enabling the PWM pins for output at the same time as
the ECCP module may cause damage to the application circuit. The ECCP module must be enabled in the
proper output mode and complete a full PWM cycle
before configuring the PWM pins as outputs. The completion of a full PWM cycle is indicated by the TMR2IF
bit being set as the second PWM period begins.
PWM AUTO-SHUTDOWN (PRSEN = 1, AUTO-RESTART ENABLED)
PWM Period
PWM Period
PWM Period
PWM Activity
Dead Time
Duty Cycle
Dead Time
Duty Cycle
Dead Time
Duty Cycle
Shutdown Event
ECCPASE bit
FIGURE 15-11:
PWM AUTO-SHUTDOWN (PRSEN = 0, AUTO-RESTART DISABLED)
PWM Period
PWM Period
PWM Period
PWM Activity
Dead Time
Duty Cycle
Dead Time
Duty Cycle
Dead Time
Duty Cycle
Shutdown Event
ECCPASE bit
ECCPASE
Cleared by Firmware
DS39636A-page 148
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
15.4.9
SETUP FOR PWM OPERATION
15.4.10
The following steps should be taken when configuring
the ECCP module for PWM operation:
1.
Configure the PWM pins, P1A and P1B (and
P1C and P1D, if used), as inputs by setting the
corresponding TRIS bits.
2. Set the PWM period by loading the PR2 register.
3. If auto-shutdown is required:
• Disable auto-shutdown (ECCP1AS = 0)
• Configure source (FLT0, Comparator 1 or
Comparator 2)
• Wait for non-shutdown condition
4. Configure the ECCP module for the desired
PWM mode and configuration by loading the
CCP1CON register with the appropriate values:
• Select one of the available output
configurations and direction with the
P1M1:P1M0 bits.
• Select the polarities of the PWM output
signals with the CCP1M3:CCP1M0 bits.
5. Set the PWM duty cycle by loading the CCPR1L
register and CCP1CON<5:4> bits.
6. For Half-Bridge Output mode, set the deadband delay by loading ECCPDEL<6:0> with the
appropriate value.
7. If auto-shutdown operation is required, load the
ECCP1AS register:
• Select the auto-shutdown sources using the
ECCPAS2:ECCPAS0 bits.
• Select the shutdown states of the PWM
output pins using the PSSAC1:PSSAC0 and
PSSBD1:PSSBD0 bits.
• Set the ECCPASE bit (ECCPAS<7>).
• Configure the comparators using the CMCON
register.
• Configure the comparator inputs as analog
inputs.
8. If auto-restart operation is required, set the
PRSEN bit (ECCPDEL<7>).
9. Configure and start TMR2:
• Clear the TMR2 interrupt flag bit by clearing
the TMR2IF bit (PIR1<1>).
• Set the TMR2 prescale value by loading the
T2CKPS bits (T2CON<1:0>).
• Enable Timer2 by setting the TMR2ON bit
(T2CON<2>).
10. Enable PWM outputs after a new PWM cycle
has started:
• Wait until TMRn overflows (TMRnIF bit is set).
• Enable the CCP1/P1A, P1B, P1C and/or P1D
pin outputs by clearing the respective TRIS
bits.
• Clear the ECCPASE bit (ECCPAS<7>).
 2004 Microchip Technology Inc.
OPERATION IN POWER MANAGED
MODES
In Sleep mode, all clock sources are disabled. Timer2
will not increment and the state of the module will not
change. If the ECCP pin is driving a value, it will
continue to drive that value. When the device wakes
up, it will continue from this state. If Two-Speed Startups are enabled, the initial start-up frequency from
INTOSC and the postscaler may not be stable
immediately.
In PRI_IDLE mode, the primary clock will continue to
clock the ECCP module without change. In all other
power managed modes, the selected power managed
mode clock will clock Timer2. Other power managed
mode clocks will most likely be different than the
primary clock frequency.
15.4.10.1
Operation with Fail-Safe
Clock Monitor
If the Fail-Safe Clock Monitor is enabled, a clock failure
will force the device into the RC_RUN Power Managed
mode and the OSCFIF bit (PIR2<7>) will be set. The
ECCP will then be clocked from the internal oscillator
clock source, which may have a different clock
frequency than the primary clock.
See the previous section for additional details.
15.4.11
EFFECTS OF A RESET
Both Power-on Reset and subsequent Resets will force
all ports to Input mode and the CCP registers to their
Reset states.
This forces the Enhanced CCP module to reset to a
state compatible with the standard CCP module.
Preliminary
DS39636A-page 149
PIC18F2X1X/4X1X
TABLE 15-3:
Name
INTCON
RCON
REGISTERS ASSOCIATED WITH ECCP1 MODULE AND TIMER1 TO TIMER3
Bit 7
Bit 6
GIE/GIEH PEIE/GIEL
IPEN
SBOREN(2)
Reset
Values
on page
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
TMR0IE
INT0IE
RBIE
TMR0IF
INT0IF
RBIF
49
—
RI
TO
PD
POR
BOR
48
PIR1
PSPIF(1)
ADIF
RCIF
TXIF
SSPIF
CCP1IF
TMR2IF
TMR1IF
52
PIE1
PSPIE(1)
ADIE
RCIE
TXIE
SSPIE
CCP1IE
TMR2IE
TMR1IE
52
IPR1
PSPIP(1)
ADIP
RCIP
TXIP
SSPIP
CCP1IP
TMR2IP
TMR1IP
52
PIR2
OSCFIF
CMIF
—
—
BCLIF
HLVDIF
TMR3IF
CCP2IF
52
PIE2
OSCFIE
CMIE
—
—
BCLIE
HLVDIE
TMR3IE
CCP2IE
52
IPR2
OSCFIP
CMIP
—
—
BCLIP
HLVDIP
TMR3IP
CCP2IP
52
TRISB
PORTB Data Direction Control Register
52
TRISC
PORTC Data Direction Control Register
52
TRISD
PORTD Data Direction Control Register
52
TMR1L
Timer1 Register Low Byte
50
TMR1H
Timer1 Register High Byte
50
T1CON
TMR2
T2CON
RD16
T1RUN
T1CKPS1
T1CKPS0
T1OSCEN
T1SYNC
TMR1CS
TMR1ON
Timer2 Register
—
50
50
T2OUTPS3 T2OUTPS2 T2OUTPS1 T2OUTPS0 TMR2ON T2CKPS1 T2CKPS0
50
PR2
Timer2 Period Register
50
TMR3L
Timer3 Register Low Byte
51
TMR3H
Timer3 Register High Byte
T3CON
RD16
T3CCP2
51
T3CKPS1
T3CKPS0
T3CCP1
T3SYNC
TMR3CS
TMR3ON
51
CCPR1L
Capture/Compare/PWM Register 1 Low Byte
51
CCPR1H
Capture/Compare/PWM Register 1 High Byte
51
CCP1CON
ECCP1AS
PWM1CON
Legend:
Note 1:
2:
P1M1
P1M0
ECCPASE ECCPAS2
PRSEN
PDC6(1)
DC1B1
DC1B0
CCP1M3
CCP1M2
ECCPAS1
ECCPAS0
PSSAC1
PSSAC0
PDC5(1)
PDC4(1)
PDC3(1)
PDC2(1)
CCP1M1
CCP1M0
PSSBD1(1) PSSBD0(1)
PDC1(1)
PDC0(1)
51
51
51
— = unimplemented, read as ‘0’. Shaded cells are not used during ECCP operation.
These bits are unimplemented on 28-pin devices and read as ‘0’.
The SBOREN bit is only available when the BOREN1:BOREN0 configuration bits = 01; otherwise, it is disabled
and reads as ‘0’. See Section 4.4 “Brown-out Reset (BOR)”.
DS39636A-page 150
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
16.0
16.1
MASTER SYNCHRONOUS
SERIAL PORT (MSSP)
MODULE
16.3
SPI Mode
The SPI mode allows 8 bits of data to be synchronously
transmitted and received simultaneously. All four SPI
modes are supported. To accomplish communication,
typically three pins are used:
MSSP Module Overview
The Master Synchronous Serial Port (MSSP) module is
a serial interface, useful for communicating with other
peripheral or microcontroller devices. These peripheral
devices may be serial EEPROMs, shift registers,
display drivers, A/D converters, etc. The MSSP module
can operate in one of two modes:
• Serial Peripheral Interface (SPI)
• Inter-Integrated Circuit (I2C)
- Full Master mode
- Slave mode (with general address call)
• Serial Data Out (SDO) – RC5/SDO
• Serial Data In (SDI) – RC4/SDI/SDA
• Serial Clock (SCK) – RC3/SCK/SCL
Additionally, a fourth pin may be used when in a Slave
mode of operation:
• Slave Select (SS) – RA5/SS
Figure 16-1 shows the block diagram of the MSSP
module when operating in SPI mode.
FIGURE 16-1:
The I2C interface supports the following modes in
hardware:
MSSP BLOCK DIAGRAM
(SPI™ MODE)
Internal
Data Bus
• Master mode
• Multi-Master mode
• Slave mode
Read
Write
SSPBUF reg
16.2
Control Registers
The MSSP module has three associated registers.
These include a status register (SSPSTAT) and two
control registers (SSPCON1 and SSPCON2). The use
of these registers and their individual configuration bits
differ significantly depending on whether the MSSP
module is operated in SPI or I2C mode.
RC4/SDI/SDA
Additional details are provided under the individual
sections.
RA5/AN4/SS/
HLVDIN/C2OUT
SSPSR reg
RC5/SDO
Shift
Clock
bit 0
SS Control
Enable
Edge
Select
2
Clock Select
RC3/SCK/
SCL
SSPM3:SSPM0
SMP:CKE 4
TMR2 Output
2
2
Edge
Select
Prescaler TOSC
4, 16, 64
(
)
Data to TX/RX in SSPSR
TRIS bit
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 151
PIC18F2X1X/4X1X
16.3.1
REGISTERS
The MSSP module has four registers for SPI mode
operation. These are:
SSPSR is the shift register used for shifting data in or
out. SSPBUF is the buffer register to which data bytes
are written to or read from.
In receive operations, SSPSR and SSPBUF together
create a double-buffered receiver. When SSPSR
receives a complete byte, it is transferred to SSPBUF
and the SSPIF interrupt is set.
• MSSP Control Register 1 (SSPCON1)
• MSSP Status Register (SSPSTAT)
• Serial Receive/Transmit Buffer Register
(SSPBUF)
• MSSP Shift Register (SSPSR) – Not directly
accessible
During transmission, the SSPBUF is not doublebuffered. A write to SSPBUF will write to both SSPBUF
and SSPSR.
SSPCON1 and SSPSTAT are the control and status
registers in SPI mode operation. The SSPCON1
register is readable and writable. The lower 6 bits of
the SSPSTAT are read-only. The upper two bits of the
SSPSTAT are read/write.
REGISTER 16-1:
SSPSTAT: MSSP STATUS REGISTER (SPI MODE)
R/W-0
R/W-0
R-0
R-0
R-0
R-0
R-0
R-0
SMP
CKE
D/A
P
S
R/W
UA
BF
bit 7
bit 0
bit 7
SMP: Sample bit
SPI Master mode:
1 = Input data sampled at end of data output time
0 = Input data sampled at middle of data output time
SPI Slave mode:
SMP must be cleared when SPI operation is used in Slave mode.
bit 6
CKE: SPI Clock Select bit
1 = Transmit occurs on transition from active to Idle clock state
0 = Transmit occurs on transition from Idle to active clock state
Note:
Polarity of clock state is set by the CKP bit (SSPCON1<4>).
bit 5
D/A: Data/Address bit
Used in I2C mode only.
bit 4
P: Stop bit
Used in I2C mode only. This bit is cleared when the MSSP module is disabled; SSPEN is
cleared.
bit 3
S: Start bit
Used in I2C mode only.
bit 2
R/W: Read/Write bit Information
Used in I2C mode only.
bit 1
UA: Update Address bit
Used in I2C mode only.
bit 0
BF: Buffer Full Status bit (Receive mode only)
1 = Receive complete, SSPBUF is full
0 = Receive not complete, SSPBUF is empty
Legend:
DS39636A-page 152
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
Preliminary
x = Bit is unknown
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
REGISTER 16-2:
SSPCON1: MSSP CONTROL REGISTER 1 (SPI MODE)
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
WCOL
SSPOV
SSPEN
CKP
SSPM3
SSPM2
SSPM1
SSPM0
bit 7
bit 0
bit 7
WCOL: Write Collision Detect bit (Transmit mode only)
1 = The SSPBUF register is written while it is still transmitting the previous word
(must be cleared in software)
0 = No collision
bit 6
SSPOV: Receive Overflow Indicator bit
SPI Slave mode:
1 = A new byte is received while the SSPBUF register is still holding the previous data. In case
of overflow, the data in SSPSR is lost. Overflow can only occur in Slave mode. The user
must read the SSPBUF, even if only transmitting data, to avoid setting overflow (must be
cleared in software).
0 = No overflow
Note:
bit 5
In Master mode, the overflow bit is not set since each new reception (and
transmission) is initiated by writing to the SSPBUF register.
SSPEN: Synchronous Serial Port Enable bit
1 = Enables serial port and configures SCK, SDO, SDI and SS as serial port pins
0 = Disables serial port and configures these pins as I/O port pins
Note:
When enabled, these pins must be properly configured as input or output.
bit 4
CKP: Clock Polarity Select bit
1 = Idle state for clock is a high level
0 = Idle state for clock is a low level
bit 3-0
SSPM3:SSPM0: Synchronous Serial Port Mode Select bits
0101 = SPI Slave mode, clock = SCK pin, SS pin control disabled, SS can be used as I/O pin
0100 = SPI Slave mode, clock = SCK pin, SS pin control enabled
0011 = SPI Master mode, clock = TMR2 output/2
0010 = SPI Master mode, clock = FOSC/64
0001 = SPI Master mode, clock = FOSC/16
0000 = SPI Master mode, clock = FOSC/4
Note:
Bit combinations not specifically listed here are either reserved or implemented in
I2C mode only.
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
 2004 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS39636A-page 153
PIC18F2X1X/4X1X
16.3.2
OPERATION
When initializing SPI operation, several options need to
be specified. This is done by programming the
appropriate control bits (SSPCON1<5:0> and
SSPSTAT<7:6>). These control bits allow the following
to be specified:
•
•
•
•
Master mode (SCK is the clock output)
Slave mode (SCK is the clock input)
Clock Polarity (Idle state of SCK)
Data Input Sample Phase (middle or end of data
output time)
• Clock Edge (output data on rising/falling edge of
SCK)
• Clock Rate (Master mode only)
• Slave Select mode (Slave mode only)
The MSSP consists of a Transmit/Receive Shift register (SSPSR) and a Buffer register (SSPBUF). The
SSPSR shifts the data in and out of the device, MSb
first. The SSPBUF holds the data that was written to the
SSPSR until the received data is ready. Once the 8 bits
of data have been received, that byte is moved to the
SSPBUF register. Then, the Buffer Full detect bit, BF
(SSPSTAT<0>) and the interrupt flag bit, SSPIF, are
set. This double-buffering of the received data
(SSPBUF) allows the next byte to start reception before
EXAMPLE 16-1:
LOOP
reading the data that was just received. Any write to the
SSPBUF register during transmission/reception of data
will be ignored and the write collision detect bit, WCOL
(SSPCON1<7>), will be set. User software must clear
the WCOL bit so that it can be determined if the following write(s) to the SSPBUF register completed
successfully.
When the application software is expecting to receive
valid data, the SSPBUF should be read before the next
byte of data to transfer is written to the SSPBUF. The
Buffer Full bit, BF (SSPSTAT<0>), indicates when
SSPBUF has been loaded with the received data
(transmission is complete). When the SSPBUF is read,
the BF bit is cleared. This data may be irrelevant if the
SPI interface is only a transmitter. Generally, the MSSP
interrupt is used to determine when the transmission/
reception has completed. The SSPBUF must be read
and/or written. If the interrupt method is not going to be
used, then software polling can be done to ensure that
a write collision does not occur. Example 16-1 shows
the loading of the SSPBUF (SSPSR) for data
transmission.
The SSPSR is not directly readable or writable and can
only be accessed by addressing the SSPBUF register.
Additionally, the MSSP status register (SSPSTAT)
indicates the various status conditions.
LOADING THE SSPBUF (SSPSR) REGISTER
BTFSS
BRA
MOVF
SSPSTAT, BF
LOOP
SSPBUF, W
;Has data been received (transmit complete)?
;No
;WREG reg = contents of SSPBUF
MOVWF
RXDATA
;Save in user RAM, if data is meaningful
MOVF
MOVWF
TXDATA, W
SSPBUF
;W reg = contents of TXDATA
;New data to xmit
DS39636A-page 154
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
16.3.3
ENABLING SPI I/O
16.3.4
To enable the serial port, SSP Enable bit, SSPEN
(SSPCON1<5>), must be set. To reset or reconfigure
SPI mode, clear the SSPEN bit, reinitialize the
SSPCON registers and then set the SSPEN bit. This
configures the SDI, SDO, SCK and SS pins as serial
port pins. For the pins to behave as the serial port function, some must have their data direction bits (in the
TRIS register) appropriately programmed as follows:
• SDI is automatically controlled by the SPI module
• SDO must have TRISC<5> bit cleared
• SCK (Master mode) must have TRISC<3> bit
cleared
• SCK (Slave mode) must have TRISC<3> bit set
• SS must have TRISA<5> bit set
TYPICAL CONNECTION
Figure 16-2 shows a typical connection between two
microcontrollers. The master controller (Processor 1)
initiates the data transfer by sending the SCK signal.
Data is shifted out of both shift registers on their programmed clock edge and latched on the opposite edge
of the clock. Both processors should be programmed to
the same Clock Polarity (CKP), then both controllers
would send and receive data at the same time.
Whether the data is meaningful (or dummy data)
depends on the application software. This leads to
three scenarios for data transmission:
• Master sends data – Slave sends dummy data
• Master sends data – Slave sends data
• Master sends dummy data – Slave sends data
Any serial port function that is not desired may be
overridden by programming the corresponding Data
Direction (TRIS) register to the opposite value.
FIGURE 16-2:
SPI™ MASTER/SLAVE CONNECTION
SPI™ Master SSPM3:SSPM0 = 00xxb
SPI™ Slave SSPM3:SSPM0 = 010xb
SDO
SDI
Serial Input Buffer
(SSPBUF)
SDI
Shift Register
(SSPSR)
MSb
Serial Input Buffer
(SSPBUF)
SDO
LSb
MSb
SCK
Serial Clock
PROCESSOR 1
 2004 Microchip Technology Inc.
Shift Register
(SSPSR)
LSb
SCK
PROCESSOR 2
Preliminary
DS39636A-page 155
PIC18F2X1X/4X1X
16.3.5
MASTER MODE
The clock polarity is selected by appropriately
programming the CKP bit (SSPCON1<4>). This then,
would give waveforms for SPI communication as
shown in Figure 16-3, Figure 16-5 and Figure 16-6,
where the MSB is transmitted first. In Master mode, the
SPI clock rate (bit rate) is user programmable to be one
of the following:
The master can initiate the data transfer at any time
because it controls the SCK. The master determines
when the slave (Processor 2, Figure 16-2) is to
broadcast data by the software protocol.
In Master mode, the data is transmitted/received as
soon as the SSPBUF register is written to. If the SPI
interface is only going to receive, the SDO output could
be disabled (programmed as an input). The SSPSR
register will continue to shift in the signal present on the
SDI pin at the programmed clock rate. As each byte is
received, it will be loaded into the SSPBUF register as
if a normal received byte (interrupts and status bits
appropriately set). This could be useful in receiver
applications as a “Line Activity Monitor” mode.
FIGURE 16-3:
•
•
•
•
FOSC/4 (or TCY)
FOSC/16 (or 4 • TCY)
FOSC/64 (or 16 • TCY)
Timer2 output/2
This allows a maximum data rate (at 40 MHz) of
10.00 Mbps.
Figure 16-3 shows the waveforms for Master mode.
When the CKE bit is set, the SDO data is valid before
there is a clock edge on SCK. The change of the input
sample is shown based on the state of the SMP bit. The
time when the SSPBUF is loaded with the received
data is shown.
SPI™ MODE WAVEFORM (MASTER MODE)
Write to
SSPBUF
SCK
(CKP = 0
CKE = 0)
SCK
(CKP = 1
CKE = 0)
4 Clock
Modes
SCK
(CKP = 0
CKE = 1)
SCK
(CKP = 1
CKE = 1)
SDO
(CKE = 0)
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
SDO
(CKE = 1)
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
SDI
(SMP = 0)
bit 0
bit 7
Input
Sample
(SMP = 0)
SDI
(SMP = 1)
bit 0
bit 7
Input
Sample
(SMP = 1)
SSPIF
Next Q4 Cycle
after Q2↓
SSPSR to
SSPBUF
DS39636A-page 156
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
16.3.6
SLAVE MODE
In Slave mode, the data is transmitted and received as
the external clock pulses appear on SCK. When the
last bit is latched, the SSPIF interrupt flag bit is set.
Before enabling the module in SPI Slave mode, the
clock line must match the proper Idle state. The clock
line can be observed by reading the SCK pin. The Idle
state is determined by the CKP bit (SSPCON1<4>).
While in Slave mode, the external clock is supplied by
the external clock source on the SCK pin. This external
clock must meet the minimum high and low times as
specified in the electrical specifications.
While in Sleep mode, the slave can transmit/receive
data. When a byte is received, the device will wake-up
from Sleep.
16.3.7
SLAVE SELECT
SYNCHRONIZATION
The SS pin allows a Synchronous Slave mode. The
SPI operation must be in Slave mode with SS pin
control enabled (SSPCON1<3:0> = 04h). When the SS
pin is low, transmission and reception are enabled and
FIGURE 16-4:
the SDO pin is driven. When the SS pin goes high, the
SDO pin is no longer driven, even if in the middle of a
transmitted byte and becomes a floating output.
External pull-up/pull-down resistors may be desirable
depending on the application.
Note 1: When the SPI operation is in Slave mode
with
SS
pin
control
enabled
(SSPCON<3:0> = 0100), the SPI module
will reset if the SS pin is set to VDD.
2: If the SPI operation is used in Slave mode
with CKE set, then the SS pin control
must be enabled.
When the SPI module resets, the bit counter is forced
to ‘0’. This can be done by either forcing the SS pin to
a high level or clearing the SSPEN bit.
To emulate two-wire communication, the SDO pin can
be connected to the SDI pin. When the SPI module
needs to operate as a receiver, the SDO pin can be
configured as an input. This disables transmissions
from the SDO. The SDI can always be left as an input
(SDI function) since it cannot create a bus conflict.
SLAVE SYNCHRONIZATION WAVEFORM
SS
SCK
(CKP = 0
CKE = 0)
SCK
(CKP = 1
CKE = 0)
Write to
SSPBUF
SDO
SDI
(SMP = 0)
bit 7
bit 6
bit 7
bit 0
bit 0
bit 7
bit 7
Input
Sample
(SMP = 0)
SSPIF
Interrupt
Flag
Next Q4 Cycle
after Q2↓
SSPSR to
SSPBUF
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 157
PIC18F2X1X/4X1X
FIGURE 16-5:
SPI™ MODE WAVEFORM (SLAVE MODE WITH CKE = 0)
SS
Optional
SCK
(CKP = 0
CKE = 0)
SCK
(CKP = 1
CKE = 0)
Write to
SSPBUF
SDO
bit 7
SDI
(SMP = 0)
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
bit 0
bit 7
Input
Sample
(SMP = 0)
SSPIF
Interrupt
Flag
Next Q4 Cycle
after Q2↓
SSPSR to
SSPBUF
FIGURE 16-6:
SPI™ MODE WAVEFORM (SLAVE MODE WITH CKE = 1)
SS
Not Optional
SCK
(CKP = 0
CKE = 1)
SCK
(CKP = 1
CKE = 1)
Write to
SSPBUF
SDO
SDI
(SMP = 0)
bit 6
bit 7
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
bit 0
bit 7
Input
Sample
(SMP = 0)
SSPIF
Interrupt
Flag
Next Q4 Cycle
after Q2↓
SSPSR to
SSPBUF
DS39636A-page 158
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
16.3.8
OPERATION IN POWER MANAGED
MODES
16.3.9
In SPI Master mode, module clocks may be operating
at a different speed than when in full power mode. In
the case of the Sleep mode, all clocks are halted.
In Idle modes, a clock is provided to the peripherals.
That clock should be from the primary clock source, the
secondary clock (Timer1 oscillator at 32.768 kHz) or
the INTOSC source. See Section 2.7 “Clock Sources
and Oscillator Switching” for additional information.
EFFECTS OF A RESET
A Reset disables the MSSP module and terminates the
current transfer.
16.3.10
BUS MODE COMPATIBILITY
Table 16-1 shows the compatibility between the
standard SPI modes and the states of the CKP and
CKE control bits.
TABLE 16-1:
SPI BUS MODES
Control Bits State
In most cases, the speed that the master clocks SPI
data is not important; however, this should be
evaluated for each system.
Standard SPI™
Mode Terminology
CKP
CKE
If MSSP interrupts are enabled, they can wake the
controller from Sleep mode, or one of the Idle modes,
when the master completes sending data. If an exit
from Sleep or Idle mode is not desired, MSSP
interrupts should be disabled.
0, 0
0
1
0, 1
0
0
1, 0
1
1
1, 1
1
0
If the Sleep mode is selected, all module clocks are
halted and the transmission/reception will remain in
that state until the devices wakes. After the device
returns to Run mode, the module will resume
transmitting and receiving data.
There is also an SMP bit which controls when the data
is sampled.
In SPI Slave mode, the SPI Transmit/Receive Shift
register operates asynchronously to the device. This
allows the device to be placed in any power managed
mode and data to be shifted into the SPI Transmit/
Receive Shift register. When all 8 bits have been
received, the MSSP interrupt flag bit will be set and if
enabled, will wake the device.
TABLE 16-2:
Name
REGISTERS ASSOCIATED WITH SPI OPERATION
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
Values
on page
INT0IE
RBIE
TMR0IF
INT0IF
RBIF
49
INTCON
GIE/GIEH PEIE/GIEL TMR0IE
PIR1
PSPIF(1)
ADIF
RCIF
TXIF
SSPIF
CCP1IF
TMR2IF
TMR1IF
52
PIE1
PSPIE(1)
ADIE
RCIE
TXIE
SSPIE
CCP1IE
TMR2IE
TMR1IE
52
IPR1
PSPIP(1)
ADIP
RCIP
TXIP
SSPIP
CCP1IP
TMR2IP
TMR1IP
TRISA
TRISA7(2) TRISA6(2) PORTA Data Direction Control Register
52
TRISC
PORTC Data Direction Control Register
52
SSPBUF
SSP Receive Buffer/Transmit Register
50
52
SSPCON1
WCOL
SSPOV
SSPEN
CKP
SSPM3
SSPM2
SSPM1
SSPM0
50
SSPSTAT
SMP
CKE
D/A
P
S
R/W
UA
BF
50
Legend: Shaded cells are not used by the MSSP in SPI mode.
Note 1: These bits are unimplemented on 28-pin devices and read as ‘0’.
2: PORTA<7:6> and their direction bits are individually configured as port pins based on various primary
oscillator modes. When disabled, these bits read as ‘0’.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 159
PIC18F2X1X/4X1X
16.4
I2C Mode
16.4.1
The MSSP module in I 2C mode fully implements all
master and slave functions (including general call
support) and provides interrupts on Start and Stop bits
in hardware to determine a free bus (multi-master
function). The MSSP module implements the standard
mode specifications, as well as 7-bit and 10-bit
addressing.
Two pins are used for data transfer:
• Serial clock (SCL) – RC3/SCK/SCL
• Serial data (SDA) – RC4/SDI/SDA
The user must configure these pins as inputs or outputs
through the TRISC<4:3> bits.
FIGURE 16-7:
MSSP BLOCK DIAGRAM
(I2C™ MODE)
Write
Shift
Clock
MSb
LSb
Match Detect
Addr Match
DS39636A-page 160
SSPCON1, SSPCON2 and SSPSTAT are the control
and status registers in I2C mode operation. The
SSPCON1 and SSPCON2 registers are readable and
writable. The lower 6 bits of the SSPSTAT are read-only.
The upper two bits of the SSPSTAT are read/write.
During transmission, the SSPBUF is not doublebuffered. A write to SSPBUF will write to both SSPBUF
and SSPSR.
SSPADD reg
Start and
Stop bit Detect
MSSP Control Register 1 (SSPCON1)
MSSP Control Register 2 (SSPCON2)
MSSP Status Register (SSPSTAT)
Serial Receive/Transmit Buffer Register
(SSPBUF)
• MSSP Shift Register (SSPSR) – Not directly
accessible
• MSSP Address Register (SSPADD)
In receive operations, SSPSR and SSPBUF together
create a double-buffered receiver. When SSPSR
receives a complete byte, it is transferred to SSPBUF
and the SSPIF interrupt is set.
SSPSR reg
RC4/SDI/
SDA
•
•
•
•
SSPADD register holds the slave device address when
the SSP is configured in I2C Slave mode. When the
SSP is configured in Master mode, the lower seven bits
of SSPADD act as the Baud Rate Generator reload
value.
SSPBUF reg
RC3/SCK/SCL
The MSSP module has six registers for I2C operation.
These are:
SSPSR is the shift register used for shifting data in or
out. SSPBUF is the buffer register to which data bytes
are written to or read from.
Internal
Data Bus
Read
REGISTERS
Set, Reset
S, P bits
(SSPSTAT reg)
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
REGISTER 16-3:
SSPSTAT: MSSP STATUS REGISTER (I2C MODE)
R/W-0
R/W-0
R-0
R-0
R-0
R-0
R-0
R-0
SMP
CKE
D/A
P
S
R/W
UA
BF
bit 7
bit 0
bit 7
SMP: Slew Rate Control bit
In Master or Slave mode:
1 = Slew rate control disabled for Standard Speed mode (100 kHz and 1 MHz)
0 = Slew rate control enabled for High-Speed mode (400 kHz)
bit 6
CKE: SMBus Select bit
In Master or Slave mode:
1 = Enable SMBus specific inputs
0 = Disable SMBus specific inputs
bit 5
D/A: Data/Address bit
In Master mode:
Reserved.
In Slave mode:
1 = Indicates that the last byte received or transmitted was data
0 = Indicates that the last byte received or transmitted was address
bit 4
P: Stop bit
1 = Indicates that a Stop bit has been detected last
0 = Stop bit was not detected last
Note:
bit 3
S: Start bit
1 = Indicates that a Start bit has been detected last
0 = Start bit was not detected last
Note:
bit 2
This bit is cleared on Reset and when SSPEN is cleared.
This bit is cleared on Reset and when SSPEN is cleared.
R/W: Read/Write bit Information (I2C mode only)
In Slave mode:
1 = Read
0 = Write
Note:
This bit holds the R/W bit information following the last address match. This bit is only
valid from the address match to the next Start bit, Stop bit or not ACK bit.
In Master mode:
1 = Transmit is in progress
0 = Transmit is not in progress
Note:
ORing this bit with SEN, RSEN, PEN, RCEN or ACKEN will indicate if the MSSP is
in Active mode.
bit 1
UA: Update Address bit (10-bit Slave mode only)
1 = Indicates that the user needs to update the address in the SSPADD register
0 = Address does not need to be updated
bit 0
BF: Buffer Full Status bit
In Transmit mode:
1 = SSPBUF is full
0 = SSPBUF is empty
In Receive mode:
1 = SSPBUF is full (does not include the ACK and Stop bits)
0 = SSPBUF is empty (does not include the ACK and Stop bits)
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
 2004 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS39636A-page 161
PIC18F2X1X/4X1X
REGISTER 16-4:
SSPCON1: MSSP CONTROL REGISTER 1 (I2C MODE)
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
WCOL
SSPOV
SSPEN
CKP
SSPM3
SSPM2
SSPM1
SSPM0
bit 7
bit 0
bit 7
WCOL: Write Collision Detect bit
In Master Transmit mode:
1 = A write to the SSPBUF register was attempted while the I2C conditions were not valid for a
transmission to be started (must be cleared in software)
0 = No collision
In Slave Transmit mode:
1 = The SSPBUF register is written while it is still transmitting the previous word (must be
cleared in software)
0 = No collision
In Receive mode (Master or Slave modes):
This is a “don’t care” bit.
bit 6
SSPOV: Receive Overflow Indicator bit
In Receive mode:
1 = A byte is received while the SSPBUF register is still holding the previous byte (must be
cleared in software)
0 = No overflow
In Transmit mode:
This is a “don’t care” bit in Transmit mode.
bit 5
SSPEN: Synchronous Serial Port Enable bit
1 = Enables the serial port and configures the SDA and SCL pins as the serial port pins
0 = Disables serial port and configures these pins as I/O port pins
Note:
When enabled, the SDA and SCL pins must be properly configured as input or
output.
bit 4
CKP: SCK Release Control bit
In Slave mode:
1 = Release clock
0 = Holds clock low (clock stretch), used to ensure data setup time
In Master mode:
Unused in this mode.
bit 3-0
SSPM3:SSPM0: Synchronous Serial Port Mode Select bits
1111 = I2C Slave mode, 10-bit address with Start and Stop bit interrupts enabled
1110 = I2C Slave mode, 7-bit address with Start and Stop bit interrupts enabled
1011 = I2C Firmware Controlled Master mode (Slave Idle)
1000 = I2C Master mode, clock = FOSC/(4 * (SSPADD + 1))
0111 = I2C Slave mode, 10-bit address
0110 = I2C Slave mode, 7-bit address
Bit combinations not specifically listed here are either reserved or implemented in SPI mode only.
Legend:
DS39636A-page 162
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
Preliminary
x = Bit is unknown
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
REGISTER 16-5:
SSPCON2: MSSP CONTROL REGISTER 2 (I2C MODE)
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
GCEN
ACKSTAT
ACKDT
ACKEN(1)
RCEN(1)
PEN(1)
RSEN(1)
SEN(1)
bit 7
bit 0
bit 7
GCEN: General Call Enable bit (Slave mode only)
1 = Enable interrupt when a general call address (0000h) is received in the SSPSR
0 = General call address disabled
bit 6
ACKSTAT: Acknowledge Status bit (Master Transmit mode only)
1 = Acknowledge was not received from slave
0 = Acknowledge was received from slave
bit 5
ACKDT: Acknowledge Data bit (Master Receive mode only)
1 = Not Acknowledge
0 = Acknowledge
Note:
Value that will be transmitted when the user initiates an Acknowledge sequence at
the end of a receive.
bit 4
ACKEN: Acknowledge Sequence Enable bit (Master Receive mode only)(1)
1 = Initiate Acknowledge sequence on SDA and SCL pins and transmit ACKDT data bit.
Automatically cleared by hardware.
0 = Acknowledge sequence Idle
bit 3
RCEN: Receive Enable bit (Master mode only)(1)
1 = Enables Receive mode for I2C operation
0 = Receive Idle
bit 2
PEN: Stop Condition Enable bit (Master mode only)(1)
1 = Initiate Stop condition on SDA and SCL pins. Automatically cleared by hardware.
0 = Stop condition Idle
bit 1
RSEN: Repeated Start Condition Enable bit (Master mode only)(1)
1 = Initiate Repeated Start condition on SDA and SCL pins. Automatically cleared by hardware.
0 = Repeated Start condition Idle
bit 0
SEN: Start Condition Enable/Stretch Enable bit(1)
In Master mode:
1 = Initiate Start condition on SDA and SCL pins. Automatically cleared by hardware.
0 = Start condition Idle
In Slave mode:
1 = Clock stretching is enabled for both slave transmit and slave receive (stretch enabled)
0 = Clock stretching is disabled
Note 1: For bits ACKEN, RCEN, PEN, RSEN, SEN: If the I2C module is not in the Idle mode,
these bits may not be set (no spooling) and the SSPBUF may not be written (or
writes to the SSPBUF are disabled).
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
 2004 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS39636A-page 163
PIC18F2X1X/4X1X
16.4.2
OPERATION
16.4.3.1
The MSSP module functions are enabled by setting
MSSP Enable bit, SSPEN (SSPCON<5>).
The SSPCON1 register allows control of the I 2C
operation. Four mode selection bits (SSPCON<3:0>)
allow one of the following I 2C modes to be selected:
I2C Master mode clock
I 2C Slave mode (7-bit address)
I 2C Slave mode (10-bit address)
I 2C Slave mode (7-bit address) with Start and
Stop bit interrupts enabled
• I 2C Slave mode (10-bit address) with Start and
Stop bit interrupts enabled
• I 2C Firmware Controlled Master mode, slave is
Idle
•
•
•
•
16.4.3
Once the MSSP module has been enabled, it waits for
a Start condition to occur. Following the Start condition,
the 8-bits are shifted into the SSPSR register. All
incoming bits are sampled with the rising edge of the
clock (SCL) line. The value of register SSPSR<7:1> is
compared to the value of the SSPADD register. The
address is compared on the falling edge of the eighth
clock (SCL) pulse. If the addresses match and the BF
and SSPOV bits are clear, the following events occur:
1.
2.
3.
4.
Selection of any I 2C mode with the SSPEN bit set,
forces the SCL and SDA pins to be open-drain,
provided these pins are programmed to inputs by
setting the appropriate TRISC bits. To ensure proper
operation of the module, pull-up resistors must be
provided externally to the SCL and SDA pins.
SLAVE MODE
In Slave mode, the SCL and SDA pins must be configured as inputs (TRISC<4:3> set). The MSSP module
will override the input state with the output data when
required (slave-transmitter).
The I 2C Slave mode hardware will always generate an
interrupt on an address match. Through the mode
select bits, the user can also choose to interrupt on
Start and Stop bits
When an address is matched, or the data transfer after
an address match is received, the hardware automatically will generate the Acknowledge (ACK) pulse and
load the SSPBUF register with the received value
currently in the SSPSR register.
Any combination of the following conditions will cause
the MSSP module not to give this ACK pulse:
• The Buffer Full bit, BF (SSPSTAT<0>), was set
before the transfer was received.
• The overflow bit, SSPOV (SSPCON<6>), was set
before the transfer was received.
In this case, the SSPSR register value is not loaded
into the SSPBUF, but bit SSPIF (PIR1<3>) is set. The
BF bit is cleared by reading the SSPBUF register, while
bit SSPOV is cleared through software.
Addressing
The SSPSR register value is loaded into the
SSPBUF register.
The Buffer Full bit, BF, is set.
An ACK pulse is generated.
MSSP Interrupt Flag bit, SSPIF (PIR1<3>), is
set (interrupt is generated, if enabled) on the
falling edge of the ninth SCL pulse.
In 10-bit Address mode, two address bytes need to be
received by the slave. The five Most Significant bits
(MSbs) of the first address byte specify if this is a 10-bit
address. Bit R/W (SSPSTAT<2>) must specify a write so
the slave device will receive the second address byte.
For a 10-bit address, the first byte would equal ‘11110
A9 A8 0’, where ‘A9’ and ‘A8’ are the two MSbs of the
address. The sequence of events for 10-bit address is as
follows, with steps 7 through 9 for the slave-transmitter:
1.
2.
3.
4.
5.
6.
7.
8.
9.
Receive first (high) byte of address (bits SSPIF,
BF and UA (SSPSTAT<1>) are set).
Update the SSPADD register with second (low)
byte of address (clears bit UA and releases the
SCL line).
Read the SSPBUF register (clears bit BF) and
clear flag bit SSPIF.
Receive second (low) byte of address (bits
SSPIF, BF and UA are set).
Update the SSPADD register with the first (high)
byte of address. If match releases SCL line, this
will clear bit UA.
Read the SSPBUF register (clears bit BF) and
clear flag bit SSPIF.
Receive Repeated Start condition.
Receive first (high) byte of address (bits SSPIF
and BF are set).
Read the SSPBUF register (clears bit BF) and
clear flag bit SSPIF.
The SCL clock input must have a minimum high and
low for proper operation. The high and low times of the
I2C specification, as well as the requirement of the
MSSP module, are shown in timing parameter 100 and
parameter 101.
DS39636A-page 164
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
16.4.3.2
Reception
16.4.3.3
When the R/W bit of the address byte is clear and an
address match occurs, the R/W bit of the SSPSTAT
register is cleared. The received address is loaded into
the SSPBUF register and the SDA line is held low
(ACK).
When the address byte overflow condition exists, then
the no Acknowledge (ACK) pulse is given. An overflow
condition is defined as either bit BF (SSPSTAT<0>) is
set, or bit SSPOV (SSPCON1<6>) is set.
An MSSP interrupt is generated for each data transfer
byte. Flag bit, SSPIF (PIR1<3>), must be cleared in
software. The SSPSTAT register is used to determine
the status of the byte.
If SEN is enabled (SSPCON2<0> = 1), RC3/SCK/SCL
will be held low (clock stretch) following each data
transfer. The clock must be released by setting bit CKP
(SSPCON<4>). See Section 16.4.4 “Clock Stretching”
for more detail.
Transmission
When the R/W bit of the incoming address byte is set
and an address match occurs, the R/W bit of the
SSPSTAT register is set. The received address is
loaded into the SSPBUF register. The ACK pulse will
be sent on the ninth bit and pin RC3/SCK/SCL is held
low regardless of SEN (see Section 16.4.4 “Clock
Stretching” for more detail). By stretching the clock,
the master will be unable to assert another clock pulse
until the slave is done preparing the transmit data. The
transmit data must be loaded into the SSPBUF register
which also loads the SSPSR register. Then pin RC3/
SCK/SCL should be enabled by setting bit CKP
(SSPCON1<4>). The eight data bits are shifted out on
the falling edge of the SCL input. This ensures that the
SDA signal is valid during the SCL high time
(Figure 16-9).
The ACK pulse from the master-receiver is latched on
the rising edge of the ninth SCL input pulse. If the SDA
line is high (not ACK), then the data transfer is complete. In this case, when the ACK is latched by the
slave, the slave logic is reset (resets SSPSTAT register) and the slave monitors for another occurrence of
the Start bit. If the SDA line was low (ACK), the next
transmit data must be loaded into the SSPBUF register.
Again, pin RC3/SCK/SCL must be enabled by setting
bit CKP.
An MSSP interrupt is generated for each data transfer
byte. The SSPIF bit must be cleared in software and
the SSPSTAT register is used to determine the status
of the byte. The SSPIF bit is set on the falling edge of
the ninth clock pulse.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 165
DS39636A-page 166
Preliminary
CKP
2
A6
3
4
A4
5
A3
Receiving Address
A5
6
A2
(CKP does not reset to ‘0’ when SEN = ‘0’)
SSPOV (SSPCON1<6>)
BF (SSPSTAT<0>)
(PIR1<3>)
SSPIF
1
SCL
S
A7
7
A1
8
9
ACK
R/W = 0
1
D7
3
4
D4
5
D3
Receiving Data
D5
Cleared in software
SSPBUF is read
2
D6
6
D2
7
D1
8
D0
9
ACK
1
D7
2
D6
3
4
D4
5
D3
Receiving Data
D5
6
D2
7
D1
8
D0
Bus master
terminates
transfer
P
SSPOV is set
because SSPBUF is
still full. ACK is not sent.
9
ACK
FIGURE 16-8:
SDA
PIC18F2X1X/4X1X
I2C™ SLAVE MODE TIMING WITH SEN = 0 (RECEPTION, 7-BIT ADDRESS)
 2004 Microchip Technology Inc.
 2004 Microchip Technology Inc.
1
Preliminary
CKP
2
A6
Data in
sampled
BF (SSPSTAT<0>)
SSPIF (PIR1<3>)
S
A7
3
A5
4
A4
5
A3
6
A2
Receiving Address
7
A1
8
R/W = 0
9
ACK
SCL held low
while CPU
responds to SSPIF
1
D7
3
D5
4
D4
5
D3
6
D2
CKP is set in software
SSPBUF is written in software
Cleared in software
2
D6
Transmitting Data
7
8
D0
9
ACK
From SSPIF ISR
D1
1
D7
4
D4
5
D3
6
D2
CKP is set in software
7
8
D0
9
ACK
From SSPIF ISR
D1
Transmitting Data
Cleared in software
3
D5
SSPBUF is written in software
2
D6
P
FIGURE 16-9:
SCL
SDA
PIC18F2X1X/4X1X
I2C™ SLAVE MODE TIMING (TRANSMISSION, 7-BIT ADDRESS)
DS39636A-page 167
DS39636A-page 168
2
1
Preliminary
4
1
5
0
7
UA is set indicating that
the SSPADD needs to be
updated
SSPBUF is written with
contents of SSPSR
6
A9 A8
8
9
(CKP does not reset to ‘0’ when SEN = 0)
UA (SSPSTAT<1>)
SSPOV (SSPCON1<6>)
CKP
3
1
Cleared in software
BF (SSPSTAT<0>)
(PIR1<3>)
SSPIF
1
SCL
S
1
ACK
R/W = 0
A7
2
4
A4
5
A3
6
A2
8
9
A0 ACK
UA is set indicating that
SSPADD needs to be
updated
Cleared by hardware
when SSPADD is updated
with low byte of address
7
A1
Cleared in software
3
A5
Dummy read of SSPBUF
to clear BF flag
1
A6
Receive Second Byte of Address
1
D7
4
5
6
7
D1
Cleared in software
3
D2
Cleared by hardware when
SSPADD is updated with high
byte of address
2
D3
Receive Data Byte
D6 D5 D4
Clock is held low until
update of SSPADD has
taken place
8
9
1
2
4
5
6
D3 D2
Cleared in software
3
D0 ACK D7 D6 D5 D4
Receive Data Byte
7
8
D1 D0
9
P
Bus master
terminates
transfer
SSPOV is set
because SSPBUF is
still full. ACK is not sent.
ACK
FIGURE 16-10:
SDA
Receive First Byte of Address
Clock is held low until
update of SSPADD has
taken place
PIC18F2X1X/4X1X
I2C™ SLAVE MODE TIMING WITH SEN = 0 (RECEPTION, 10-BIT ADDRESS)
 2004 Microchip Technology Inc.
 2004 Microchip Technology Inc.
2
Preliminary
CKP (SSPCON1<4>)
UA (SSPSTAT<1>)
BF (SSPSTAT<0>)
(PIR1<3>)
SSPIF
1
S
SCL
1
4
1
5
0
6
7
A9 A8
8
UA is set indicating that
the SSPADD needs to be
updated
SSPBUF is written with
contents of SSPSR
3
1
Receive First Byte of Address
1
9
ACK
1
3
4
5
Cleared in software
2
7
UA is set indicating that
SSPADD needs to be
updated
Cleared by hardware when
SSPADD is updated with low
byte of address
6
A6 A5 A4 A3 A2 A1
8
A0
Receive Second Byte of Address
Dummy read of SSPBUF
to clear BF flag
A7
9
ACK
2
3
1
4
1
Cleared in software
1
1
5
0
6
8
9
ACK
R/W=1
1
2
4
5
6
CKP is set in software
9
P
Completion of
data transmission
clears BF flag
8
ACK
Bus master
terminates
transfer
CKP is automatically cleared in hardware, holding SCL low
7
D4 D3 D2 D1 D0
Cleared in software
3
D7 D6 D5
Transmitting Data Byte
Clock is held low until
CKP is set to ‘1’
Write of SSPBUF
BF flag is clear
initiates transmit
at the end of the
third address sequence
7
A9 A8
Cleared by hardware when
SSPADD is updated with high
byte of address.
Dummy read of SSPBUF
to clear BF flag
Sr
1
Receive First Byte of Address
Clock is held low until
update of SSPADD has
taken place
FIGURE 16-11:
SDA
R/W = 0
Clock is held low until
update of SSPADD has
taken place
PIC18F2X1X/4X1X
I2C™ SLAVE MODE TIMING (TRANSMISSION, 10-BIT ADDRESS)
DS39636A-page 169
PIC18F2X1X/4X1X
16.4.4
CLOCK STRETCHING
16.4.4.3
Both 7-bit and 10-bit Slave modes implement
automatic clock stretching during a transmit sequence.
The SEN bit (SSPCON2<0>) allows clock stretching to
be enabled during receives. Setting SEN will cause
the SCL pin to be held low at the end of each data
receive sequence.
16.4.4.1
Clock Stretching for 7-bit Slave
Receive Mode (SEN = 1)
In 7-bit Slave Receive mode, on the falling edge of the
ninth clock at the end of the ACK sequence if the BF
bit is set, the CKP bit in the SSPCON1 register is
automatically cleared, forcing the SCL output to be
held low. The CKP being cleared to ‘0’ will assert the
SCL line low. The CKP bit must be set in the user’s
ISR before reception is allowed to continue. By holding
the SCL line low, the user has time to service the ISR
and read the contents of the SSPBUF before the
master device can initiate another receive sequence.
This will prevent buffer overruns from occurring (see
Figure 16-13).
Note 1: If the user reads the contents of the
SSPBUF before the falling edge of the
ninth clock, thus clearing the BF bit, the
CKP bit will not be cleared and clock
stretching will not occur.
2: The CKP bit can be set in software
regardless of the state of the BF bit. The
user should be careful to clear the BF bit
in the ISR before the next receive
sequence in order to prevent an overflow
condition.
16.4.4.2
Clock Stretching for 7-bit Slave
Transmit Mode
7-bit Slave Transmit mode implements clock stretching
by clearing the CKP bit after the falling edge of the
ninth clock if the BF bit is clear. This occurs regardless
of the state of the SEN bit.
The user’s ISR must set the CKP bit before transmission is allowed to continue. By holding the SCL line
low, the user has time to service the ISR and load the
contents of the SSPBUF before the master device can
initiate another transmit sequence (see Figure 16-9).
Note 1: If the user loads the contents of SSPBUF,
setting the BF bit before the falling edge of
the ninth clock, the CKP bit will not be
cleared and clock stretching will not occur.
2: The CKP bit can be set in software
regardless of the state of the BF bit.
16.4.4.4
Clock Stretching for 10-bit Slave
Transmit Mode
In 10-bit Slave Transmit mode, clock stretching is
controlled during the first two address sequences by
the state of the UA bit, just as it is in 10-bit Slave
Receive mode. The first two addresses are followed
by a third address sequence which contains the highorder bits of the 10-bit address and the R/W bit set to
‘1’. After the third address sequence is performed, the
UA bit is not set, the module is now configured in
Transmit mode and clock stretching is controlled by
the BF flag as in 7-bit Slave Transmit mode (see
Figure 16-11).
Clock Stretching for 10-bit Slave
Receive Mode (SEN = 1)
In 10-bit Slave Receive mode during the address
sequence, clock stretching automatically takes place
but CKP is not cleared. During this time, if the UA bit is
set after the ninth clock, clock stretching is initiated.
The UA bit is set after receiving the upper byte of the
10-bit address and following the receive of the second
byte of the 10-bit address with the R/W bit cleared to
‘0’. The release of the clock line occurs upon updating
SSPADD. Clock stretching will occur on each data
receive sequence as described in 7-bit mode.
Note:
If the user polls the UA bit and clears it by
updating the SSPADD register before the
falling edge of the ninth clock occurs and if
the user hasn’t cleared the BF bit by reading the SSPBUF register before that time,
then the CKP bit will still NOT be asserted
low. Clock stretching on the basis of the
state of the BF bit only occurs during a
data sequence, not an address sequence.
DS39636A-page 170
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
16.4.4.5
Clock Synchronization and
the CKP bit
When the CKP bit is cleared, the SCL output is forced
to ‘0’. However, clearing the CKP bit will not assert the
SCL output low until the SCL output is already
sampled low. Therefore, the CKP bit will not assert the
SCL line until an external I2C master device has
FIGURE 16-12:
already asserted the SCL line. The SCL output will
remain low until the CKP bit is set and all other
devices on the I2C bus have deasserted SCL. This
ensures that a write to the CKP bit will not violate the
minimum high time requirement for SCL (see
Figure 16-12).
CLOCK SYNCHRONIZATION TIMING
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
SDA
DX
DX – 1
SCL
CKP
Master device
asserts clock
Master device
deasserts clock
WR
SSPCON
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 171
DS39636A-page 172
Preliminary
CKP
SSPOV (SSPCON1<6>)
BF (SSPSTAT<0>)
(PIR1<3>)
SSPIF
1
SCL
S
A7
2
A6
3
4
A4
5
A3
Receiving Address
A5
6
A2
7
A1
8
9
ACK
R/W = 0
3
4
D4
5
D3
Receiving Data
D5
Cleared in software
2
D6
If BF is cleared
prior to the falling
edge of the 9th clock,
CKP will not be reset
to ‘0’ and no clock
stretching will occur
SSPBUF is read
1
D7
6
D2
7
D1
9
ACK
1
D7
BF is set after falling
edge of the 9th clock,
CKP is reset to ‘0’ and
clock stretching occurs
8
D0
CKP
written
to ‘1’ in
software
2
D6
Clock is held low until
CKP is set to ‘1’
3
4
D4
5
D3
Receiving Data
D5
6
D2
7
D1
8
D0
Bus master
terminates
transfer
P
SSPOV is set
because SSPBUF is
still full. ACK is not sent.
9
ACK
Clock is not held low
because ACK = 1
FIGURE 16-13:
SDA
Clock is not held low
because buffer full bit is
clear prior to falling edge
of 9th clock
PIC18F2X1X/4X1X
I2C™ SLAVE MODE TIMING WITH SEN = 1 (RECEPTION, 7-BIT ADDRESS)
 2004 Microchip Technology Inc.
 2004 Microchip Technology Inc.
2
1
Preliminary
UA (SSPSTAT<1>)
SSPOV (SSPCON1<6>)
CKP
3
1
4
1
5
0
6
A9
7
A8
8
UA is set indicating that
the SSPADD needs to be
updated
SSPBUF is written with
contents of SSPSR
Cleared in software
BF (SSPSTAT<0>)
(PIR1<3>)
SSPIF
1
SCL
S
1
9
ACK
R/W = 0
A7
2
4
5
A3
6
A2
Cleared in software
3
A4
7
A1
8
A0
Note: An update of the SSPADD
register before the falling
edge of the ninth clock will
have no effect on UA and
UA will remain set.
UA is set indicating that
SSPADD needs to be
updated
Cleared by hardware when
SSPADD is updated with low
byte of address after falling edge
of ninth clock
Dummy read of SSPBUF
to clear BF flag
1
A6 A5
Receive Second Byte of Address
9
ACK
2
4
5
6
Cleared in software
3
D3 D2
7
D1
9
Note: An update of the SSPADD register before
the falling edge of the ninth clock will have
no effect on UA and UA will remain set.
8
ACK
1
4
5
6
Cleared in software
3
CKP written to ‘1’
in software
2
D3 D2
Receive Data Byte
D7 D6 D5 D4
Clock is held low until
CKP is set to ‘1’
D0
Cleared by hardware when
SSPADD is updated with high
byte of address after falling edge
of ninth clock
Dummy read of SSPBUF
to clear BF flag
1
D7 D6 D5 D4
Receive Data Byte
Clock is held low until
update of SSPADD has
taken place
7
8
9
Bus master
terminates
transfer
P
SSPOV is set
because SSPBUF is
still full. ACK is not sent.
D1 D0
ACK
Clock is not held low
because ACK = 1
FIGURE 16-14:
SDA
Receive First Byte of Address
Clock is held low until
update of SSPADD has
taken place
PIC18F2X1X/4X1X
I2C™ SLAVE MODE TIMING SEN = 1 (RECEPTION, 10-BIT ADDRESS)
DS39636A-page 173
PIC18F2X1X/4X1X
16.4.5
GENERAL CALL ADDRESS
SUPPORT
If the general call address matches, the SSPSR is
transferred to the SSPBUF, the BF flag bit is set (eighth
bit) and on the falling edge of the ninth bit (ACK bit), the
SSPIF interrupt flag bit is set.
The addressing procedure for the I2C bus is such that
the first byte after the Start condition usually determines which device will be the slave addressed by the
master. The exception is the general call address which
can address all devices. When this address is used, all
devices should, in theory, respond with an
Acknowledge.
When the interrupt is serviced, the source for the
interrupt can be checked by reading the contents of the
SSPBUF. The value can be used to determine if the
address was device specific or a general call address.
In 10-bit mode, the SSPADD is required to be updated
for the second half of the address to match and the UA
bit is set (SSPSTAT<1>). If the general call address is
sampled when the GCEN bit is set, while the slave is
configured in 10-bit Address mode, then the second
half of the address is not necessary, the UA bit will not
be set and the slave will begin receiving data after the
Acknowledge (Figure 16-15).
The general call address is one of eight addresses
reserved for specific purposes by the I2C protocol. It
consists of all ‘0’s with R/W = 0.
The general call address is recognized when the
General Call Enable bit (GCEN) is enabled
(SSPCON2<7> set). Following a Start bit detect, 8 bits
are shifted into the SSPSR and the address is
compared against the SSPADD. It is also compared to
the general call address and fixed in hardware.
FIGURE 16-15:
SLAVE MODE GENERAL CALL ADDRESS SEQUENCE
(7 OR 10-BIT ADDRESS MODE)
Address is compared to General Call Address
after ACK, set interrupt
R/W = 0
ACK D7
General Call Address
SDA
Receiving Data
ACK
D6
D5
D4
D3
D2
D1
D0
2
3
4
5
6
7
8
SCL
S
1
2
3
4
5
6
7
8
9
1
9
SSPIF
BF (SSPSTAT<0>)
Cleared in software
SSPBUF is read
SSPOV (SSPCON1<6>)
‘0’
GCEN (SSPCON2<7>)
‘1’
DS39636A-page 174
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
MASTER MODE
Note:
Master mode is enabled by setting and clearing the
appropriate SSPM bits in SSPCON1 and by setting the
SSPEN bit. In Master mode, the SCL and SDA lines
are manipulated by the MSSP hardware.
Master mode of operation is supported by interrupt
generation on the detection of the Start and Stop
conditions. The Stop (P) and Start (S) bits are cleared
from a Reset or when the MSSP module is disabled.
Control of the I 2C bus may be taken when the P bit is
set, or the bus is Idle, with both the S and P bits clear.
In Firmware Controlled Master mode, user code
conducts all I 2C bus operations based on Start and
Stop bit conditions.
1.
2.
3.
4.
5.
6.
Assert a Start condition on SDA and SCL.
Assert a Repeated Start condition on SDA and
SCL.
Write to the SSPBUF register initiating
transmission of data/address.
Configure the I2C port to receive data.
Generate an Acknowledge condition at the end
of a received byte of data.
Generate a Stop condition on SDA and SCL.
FIGURE 16-16:
The following events will cause the SSP Interrupt Flag
bit, SSPIF, to be set (SSP interrupt, if enabled):
•
•
•
•
•
Once Master mode is enabled, the user has six
options.
The MSSP module, when configured in
I2C Master mode, does not allow queueing
of events. For instance, the user is not
allowed to initiate a Start condition and
immediately write the SSPBUF register to
initiate transmission before the Start condition is complete. In this case, the SSPBUF
will not be written to and the WCOL bit will
be set, indicating that a write to the
SSPBUF did not occur.
Start condition
Stop condition
Data transfer byte transmitted/received
Acknowledge transmit
Repeated Start
MSSP BLOCK DIAGRAM (I2C™ MASTER MODE)
Internal
Data Bus
Read
SSPM3:SSPM0
SSPADD<6:0>
Write
Baud
Rate
Generator
SSPBUF
Shift
Clock
SDA
SDA In
SCL In
Bus Collision
 2004 Microchip Technology Inc.
LSb
Start bit, Stop bit,
Acknowledge
Generate
Start bit Detect
Stop bit Detect
Write Collision Detect
Clock Arbitration
State Counter for
end of XMIT/RCV
Preliminary
Clock Cntl
SCL
Receive Enable
SSPSR
MSb
Clock Arbitrate/WCOL Detect
(hold off clock source)
16.4.6
Set/Reset, S, P, WCOL (SSPSTAT)
Set SSPIF, BCLIF
Reset ACKSTAT, PEN (SSPCON2)
DS39636A-page 175
PIC18F2X1X/4X1X
16.4.6.1
I2C Master Mode Operation
A typical transmit sequence would go as follows:
The master device generates all of the serial clock
pulses and the Start and Stop conditions. A transfer is
ended with a Stop condition or with a Repeated Start
condition. Since the Repeated Start condition is also
the beginning of the next serial transfer, the I2C bus will
not be released.
In Master Transmitter mode, serial data is output
through SDA, while SCL outputs the serial clock. The
first byte transmitted contains the slave address of the
receiving device (7 bits) and the Read/Write (R/W) bit.
In this case, the R/W bit will be logic ‘0’. Serial data is
transmitted 8 bits at a time. After each byte is transmitted, an Acknowledge bit is received. Start and Stop
conditions are output to indicate the beginning and the
end of a serial transfer.
In Master Receive mode, the first byte transmitted
contains the slave address of the transmitting device
(7 bits) and the R/W bit. In this case, the R/W bit will be
logic ‘1’. Thus, the first byte transmitted is a 7-bit slave
address followed by a ‘1’ to indicate the receive bit.
Serial data is received via SDA, while SCL outputs the
serial clock. Serial data is received 8 bits at a time. After
each byte is received, an Acknowledge bit is transmitted. Start and Stop conditions indicate the beginning
and end of transmission.
The Baud Rate Generator used for the SPI mode operation is used to set the SCL clock frequency for either
100 kHz, 400 kHz or 1 MHz I2C operation. See
Section 16.4.7 “Baud Rate” for more detail.
DS39636A-page 176
1.
The user generates a Start condition by setting
the Start Enable bit, SEN (SSPCON2<0>).
2. SSPIF is set. The MSSP module will wait the
required start time before any other operation
takes place.
3. The user loads the SSPBUF with the slave
address to transmit.
4. Address is shifted out the SDA pin until all 8 bits
are transmitted.
5. The MSSP module shifts in the ACK bit from the
slave device and writes its value into the
SSPCON2 register (SSPCON2<6>).
6. The MSSP module generates an interrupt at the
end of the ninth clock cycle by setting the SSPIF
bit.
7. The user loads the SSPBUF with eight bits of
data.
8. Data is shifted out the SDA pin until all 8 bits are
transmitted.
9. The MSSP module shifts in the ACK bit from the
slave device and writes its value into the
SSPCON2 register (SSPCON2<6>).
10. The MSSP module generates an interrupt at the
end of the ninth clock cycle by setting the SSPIF
bit.
11. The user generates a Stop condition by setting
the Stop Enable bit, PEN (SSPCON2<2>).
12. Interrupt is generated once the Stop condition is
complete.
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
16.4.7
BAUD RATE
2
In I C Master mode, the Baud Rate Generator (BRG)
reload value is placed in the lower 7 bits of the
SSPADD register (Figure 16-17). When a write occurs
to SSPBUF, the Baud Rate Generator will automatically
begin counting. The BRG counts down to ‘0’ and stops
until another reload has taken place. The BRG count is
decremented twice per instruction cycle (TCY) on the
Q2 and Q4 clocks. In I2C Master mode, the BRG is
reloaded automatically.
FIGURE 16-17:
Once the given operation is complete (i.e., transmission of the last data bit is followed by ACK), the internal
clock will automatically stop counting and the SCL pin
will remain in its last state.
Table 16-3 demonstrates clock rates based on
instruction cycles and the BRG value loaded into
SSPADD.
BAUD RATE GENERATOR BLOCK DIAGRAM
SSPM3:SSPM0
SSPM3:SSPM0
Reload
SCL
Control
CLKO
TABLE 16-3:
SSPADD<6:0>
Reload
BRG Down Counter
FOSC/4
I2C™ CLOCK RATE W/BRG
FOSC
FCY
FCY * 2
BRG Value
FSCL
(2 Rollovers of BRG)
40 MHz
10 MHz
20 MHz
18h
400 kHz(1)
40 MHz
10 MHz
20 MHz
1Fh
312.5 kHz
40 MHz
10 MHz
20 MHz
63h
100 kHz
16 MHz
4 MHz
8 MHz
09h
400 kHz(1)
16 MHz
4 MHz
8 MHz
0Ch
308 kHz
16 MHz
4 MHz
8 MHz
27h
100 kHz
4 MHz
1 MHz
2 MHz
02h
333 kHz(1)
4 MHz
1 MHz
2 MHz
09h
100 kHz
4 MHz
1 MHz
2 MHz
00h
1 MHz(1)
Note 1:
The I2C interface does not conform to the 400 kHz I2C specification (which applies to rates greater than
100 kHz) in all details, but may be used with care where higher rates are required by the application.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 177
PIC18F2X1X/4X1X
16.4.7.1
Clock Arbitration
Clock arbitration occurs when the master, during any
receive, transmit or Repeated Start/Stop condition,
deasserts the SCL pin (SCL allowed to float high).
When the SCL pin is allowed to float high, the Baud
Rate Generator (BRG) is suspended from counting
until the SCL pin is actually sampled high. When the
FIGURE 16-18:
SCL pin is sampled high, the Baud Rate Generator is
reloaded with the contents of SSPADD<6:0> and
begins counting. This ensures that the SCL high time
will always be at least one BRG rollover count in the
event that the clock is held low by an external device
(Figure 16-18).
BAUD RATE GENERATOR TIMING WITH CLOCK ARBITRATION
SDA
DX
DX – 1
SCL deasserted but slave holds
SCL low (clock arbitration)
SCL allowed to transition high
SCL
BRG decrements on
Q2 and Q4 cycles
BRG
Value
03h
02h
01h
00h (hold off)
03h
02h
SCL is sampled high, reload takes
place and BRG starts its count
BRG
Reload
DS39636A-page 178
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
16.4.8
I2C MASTER MODE START
CONDITION TIMING
Note:
To initiate a Start condition, the user sets the Start
Enable bit, SEN (SSPCON2<0>). If the SDA and SCL
pins are sampled high, the Baud Rate Generator is
reloaded with the contents of SSPADD<6:0> and starts
its count. If SCL and SDA are both sampled high when
the Baud Rate Generator times out (TBRG), the SDA
pin is driven low. The action of the SDA being driven
low while SCL is high is the Start condition and causes
the S bit (SSPSTAT<3>) to be set. Following this, the
Baud Rate Generator is reloaded with the contents of
SSPADD<6:0> and resumes its count. When the Baud
Rate Generator times out (TBRG), the SEN bit
(SSPCON2<0>) will be automatically cleared by
hardware; the Baud Rate Generator is suspended,
leaving the SDA line held low and the Start condition is
complete.
FIGURE 16-19:
16.4.8.1
If at the beginning of the Start condition,
the SDA and SCL pins are already sampled low, or if during the Start condition, the
SCL line is sampled low before the SDA
line is driven low, a bus collision occurs,
the Bus Collision Interrupt Flag, BCLIF, is
set, the Start condition is aborted and the
I2C module is reset into its Idle state.
WCOL Status Flag
If the user writes the SSPBUF when a Start sequence
is in progress, the WCOL is set and the contents of the
buffer are unchanged (the write doesn’t occur).
Note:
Because queueing of events is not
allowed, writing to the lower 5 bits of
SSPCON2 is disabled until the Start
condition is complete.
FIRST START BIT TIMING
Set S bit (SSPSTAT<3>)
Write to SEN bit occurs here
SDA = 1,
SCL = 1
TBRG
At completion of Start bit,
hardware clears SEN bit
and sets SSPIF bit
TBRG
Write to SSPBUF occurs here
1st bit
SDA
2nd bit
TBRG
SCL
TBRG
S
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 179
PIC18F2X1X/4X1X
16.4.9
I2C MASTER MODE REPEATED
START CONDITION TIMING
Note 1: If RSEN is programmed while any other
event is in progress, it will not take effect.
A Repeated Start condition occurs when the RSEN bit
(SSPCON2<1>) is programmed high and the I2C logic
module is in the Idle state. When the RSEN bit is set,
the SCL pin is asserted low. When the SCL pin is sampled low, the Baud Rate Generator is loaded with the
contents of SSPADD<5:0> and begins counting. The
SDA pin is released (brought high) for one Baud Rate
Generator count (TBRG). When the Baud Rate Generator times out, if SDA is sampled high, the SCL pin will
be deasserted (brought high). When SCL is sampled
high, the Baud Rate Generator is reloaded with the
contents of SSPADD<6:0> and begins counting. SDA
and SCL must be sampled high for one TBRG. This
action is then followed by assertion of the SDA pin
(SDA = 0) for one TBRG while SCL is high. Following
this, the RSEN bit (SSPCON2<1>) will be automatically
cleared and the Baud Rate Generator will not be
reloaded, leaving the SDA pin held low. As soon as a
Start condition is detected on the SDA and SCL pins,
the S bit (SSPSTAT<3>) will be set. The SSPIF bit will
not be set until the Baud Rate Generator has timed out.
2: A bus collision during the Repeated Start
condition occurs if:
• SDA is sampled low when SCL goes
from low-to-high.
• SCL goes low before SDA is
asserted low. This may indicate that
another master is attempting to
transmit a data ‘1’.
Immediately following the SSPIF bit getting set, the user
may write the SSPBUF with the 7-bit address in 7-bit
mode or the default first address in 10-bit mode. After the
first eight bits are transmitted and an ACK is received,
the user may then transmit an additional eight bits of
address (10-bit mode) or eight bits of data (7-bit mode).
16.4.9.1
If the user writes the SSPBUF when a Repeated Start
sequence is in progress, the WCOL is set and the
contents of the buffer are unchanged (the write doesn’t
occur).
Note:
FIGURE 16-20:
WCOL Status Flag
Because queueing of events is not
allowed, writing of the lower 5 bits of
SSPCON2 is disabled until the Repeated
Start condition is complete.
REPEAT START CONDITION WAVEFORM
S bit set by hardware
Write to SSPCON2
occurs here.
SDA = 1,
SCL (no change).
SDA = 1,
SCL = 1
TBRG
At completion of Start bit,
hardware clears RSEN bit
and sets SSPIF
TBRG
TBRG
1st bit
SDA
RSEN bit set by hardware
on falling edge of ninth clock,
end of Xmit
Write to SSPBUF occurs here
TBRG
SCL
TBRG
Sr = Repeated Start
DS39636A-page 180
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
16.4.10
I2C MASTER MODE
TRANSMISSION
16.4.10.3
Transmission of a data byte, a 7-bit address or the
other half of a 10-bit address is accomplished by simply
writing a value to the SSPBUF register. This action will
set the Buffer Full flag bit, BF and allow the Baud Rate
Generator to begin counting and start the next transmission. Each bit of address/data will be shifted out
onto the SDA pin after the falling edge of SCL is
asserted (see data hold time specification
parameter 106). SCL is held low for one Baud Rate
Generator rollover count (TBRG). Data should be valid
before SCL is released high (see data setup time specification parameter 107). When the SCL pin is released
high, it is held that way for TBRG. The data on the SDA
pin must remain stable for that duration and some hold
time after the next falling edge of SCL. After the eighth
bit is shifted out (the falling edge of the eighth clock),
the BF flag is cleared and the master releases SDA.
This allows the slave device being addressed to
respond with an ACK bit during the ninth bit time if an
address match occurred, or if data was received
properly. The status of ACK is written into the ACKDT
bit on the falling edge of the ninth clock. If the master
receives an Acknowledge, the Acknowledge Status bit,
ACKSTAT, is cleared. If not, the bit is set. After the ninth
clock, the SSPIF bit is set and the master clock (Baud
Rate Generator) is suspended until the next data byte
is loaded into the SSPBUF, leaving SCL low and SDA
unchanged (Figure 16-21).
After the write to the SSPBUF, each bit of the address
will be shifted out on the falling edge of SCL until all
seven address bits and the R/W bit are completed. On
the falling edge of the eighth clock, the master will
deassert the SDA pin, allowing the slave to respond
with an Acknowledge. On the falling edge of the ninth
clock, the master will sample the SDA pin to see if the
address was recognized by a slave. The status of the
ACK bit is loaded into the ACKSTAT status bit
(SSPCON2<6>). Following the falling edge of the ninth
clock transmission of the address, the SSPIF is set, the
BF flag is cleared and the Baud Rate Generator is
turned off until another write to the SSPBUF takes
place, holding SCL low and allowing SDA to float.
16.4.10.1
BF Status Flag
ACKSTAT Status Flag
In Transmit mode, the ACKSTAT bit (SSPCON2<6>) is
cleared when the slave has sent an Acknowledge
(ACK = 0) and is set when the slave does not Acknowledge (ACK = 1). A slave sends an Acknowledge when
it has recognized its address (including a general call),
or when the slave has properly received its data.
16.4.11
I2C MASTER MODE RECEPTION
Master mode reception is enabled by programming the
Receive Enable bit, RCEN (SSPCON2<3>).
Note:
The MSSP module must be in an Idle state
before the RCEN bit is set or the RCEN bit
will be disregarded.
The Baud Rate Generator begins counting and on each
rollover, the state of the SCL pin changes (high-to-low/
low-to-high) and data is shifted into the SSPSR. After
the falling edge of the eighth clock, the receive enable
flag is automatically cleared, the contents of the
SSPSR are loaded into the SSPBUF, the BF flag bit is
set, the SSPIF flag bit is set and the Baud Rate Generator is suspended from counting, holding SCL low. The
MSSP is now in Idle state awaiting the next command.
When the buffer is read by the CPU, the BF flag bit is
automatically cleared. The user can then send an
Acknowledge bit at the end of reception by setting the
Acknowledge Sequence Enable bit, ACKEN
(SSPCON2<4>).
16.4.11.1
BF Status Flag
In receive operation, the BF bit is set when an address
or data byte is loaded into SSPBUF from SSPSR. It is
cleared when the SSPBUF register is read.
16.4.11.2
SSPOV Status Flag
In receive operation, the SSPOV bit is set when 8 bits
are received into the SSPSR and the BF flag bit is
already set from a previous reception.
16.4.11.3
WCOL Status Flag
If the user writes the SSPBUF when a receive is
already in progress (i.e., SSPSR is still shifting in a data
byte), the WCOL bit is set and the contents of the buffer
are unchanged (the write doesn’t occur).
In Transmit mode, the BF bit (SSPSTAT<0>) is set
when the CPU writes to SSPBUF and is cleared when
all 8 bits are shifted out.
16.4.10.2
WCOL Status Flag
If the user writes the SSPBUF when a transmit is
already in progress (i.e., SSPSR is still shifting out a
data byte), the WCOL is set and the contents of the
buffer are unchanged (the write doesn’t occur).
WCOL must be cleared in software.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 181
DS39636A-page 182
S
Preliminary
R/W
PEN
SEN
BF (SSPSTAT<0>)
SSPIF
SCL
SDA
A6
A5
A4
A3
A2
A1
3
4
5
Cleared in software
2
6
7
8
9
After Start condition, SEN cleared by hardware
SSPBUF written
1
D7
1
SCL held low
while CPU
responds to SSPIF
ACK = ‘0’
R/W = 0
SSPBUF written with 7-bit address and R/W,
start transmit
A7
Transmit Address to Slave
3
D5
4
D4
5
D3
6
D2
7
D1
8
D0
SSPBUF is written in software
Cleared in software service routine
from SSP interrupt
2
D6
Transmitting Data or Second Half
of 10-bit Address
From slave, clear ACKSTAT bit SSPCON2<6>
P
Cleared in software
9
ACK
ACKSTAT in
SSPCON2 = 1
FIGURE 16-21:
SEN = 0
Write SSPCON2<0> SEN = 1
Start condition begins
PIC18F2X1X/4X1X
I 2C™ MASTER MODE WAVEFORM (TRANSMISSION, 7 OR 10-BIT ADDRESS)
 2004 Microchip Technology Inc.
 2004 Microchip Technology Inc.
S
Preliminary
ACKEN
SSPOV
BF
(SSPSTAT<0>)
SDA = 0, SCL = 1
while CPU
responds to SSPIF
SSPIF
SCL
SDA
1
A7
2
4
5
Cleared in software
3
6
A6 A5 A4 A3 A2
Transmit Address to Slave
7
A1
8
9
R/W = 0
ACK
ACK from Slave
2
3
5
6
7
8
D0
9
ACK
2
3
4
5
6
7
Cleared in software
Set SSPIF interrupt
at end of Acknowledge
sequence
Data shifted in on falling edge of CLK
1
D7 D6 D5 D4 D3 D2 D1
Cleared in
software
Set SSPIF at end
of receive
9
ACK is not sent
ACK
P
Set SSPIF interrupt
at end of Acknowledge sequence
Bus master
terminates
transfer
Set P bit
(SSPSTAT<4>)
and SSPIF
PEN bit = 1
written here
SSPOV is set because
SSPBUF is still full
8
D0
RCEN cleared
automatically
Set ACKEN, start Acknowledge sequence
SDA = ACKDT = 1
Receiving Data from Slave
RCEN = 1, start
next receive
ACK from Master
SDA = ACKDT = 0
Last bit is shifted into SSPSR and
contents are unloaded into SSPBUF
Cleared in software
Set SSPIF interrupt
at end of receive
4
Cleared in software
1
D7 D6 D5 D4 D3 D2 D1
Receiving Data from Slave
RCEN cleared
automatically
Master configured as a receiver
by programming SSPCON2<3> (RCEN = 1)
FIGURE 16-22:
SEN = 0
Write to SSPBUF occurs here,
start XMIT
Write to SSPCON2<0> (SEN = 1)
Begin Start condition
Write to SSPCON2<4>
to start Acknowledge sequence
SDA = ACKDT (SSPCON2<5>) = 0
PIC18F2X1X/4X1X
I 2C™ MASTER MODE WAVEFORM (RECEPTION, 7-BIT ADDRESS)
DS39636A-page 183
PIC18F2X1X/4X1X
16.4.12
ACKNOWLEDGE SEQUENCE
TIMING
16.4.13
A Stop bit is asserted on the SDA pin at the end of a
receive/transmit by setting the Stop Sequence Enable
bit, PEN (SSPCON2<2>). At the end of a receive/
transmit, the SCL line is held low after the falling edge
of the ninth clock. When the PEN bit is set, the master
will assert the SDA line low. When the SDA line is sampled low, the Baud Rate Generator is reloaded and
counts down to ‘0’. When the Baud Rate Generator
times out, the SCL pin will be brought high and one
TBRG (Baud Rate Generator rollover count) later, the
SDA pin will be deasserted. When the SDA pin is sampled high while SCL is high, the P bit (SSPSTAT<4>) is
set. A TBRG later, the PEN bit is cleared and the SSPIF
bit is set (Figure 16-24).
An Acknowledge sequence is enabled by setting the
Acknowledge Sequence Enable bit, ACKEN
(SSPCON2<4>). When this bit is set, the SCL pin is
pulled low and the contents of the Acknowledge data bit
are presented on the SDA pin. If the user wishes to generate an Acknowledge, then the ACKDT bit should be
cleared. If not, the user should set the ACKDT bit before
starting an Acknowledge sequence. The Baud Rate
Generator then counts for one rollover period (TBRG)
and the SCL pin is deasserted (pulled high). When the
SCL pin is sampled high (clock arbitration), the Baud
Rate Generator counts for TBRG. The SCL pin is then
pulled low. Following this, the ACKEN bit is automatically
cleared, the Baud Rate Generator is turned off and the
MSSP module then goes into Idle mode (Figure 16-23).
16.4.12.1
16.4.13.1
WCOL Status Flag
If the user writes the SSPBUF when a Stop sequence
is in progress, then the WCOL bit is set and the
contents of the buffer are unchanged (the write doesn’t
occur).
WCOL Status Flag
If the user writes the SSPBUF when an Acknowledge
sequence is in progress, then WCOL is set and the
contents of the buffer are unchanged (the write doesn’t
occur).
FIGURE 16-23:
STOP CONDITION TIMING
ACKNOWLEDGE SEQUENCE WAVEFORM
Acknowledge sequence starts here,
write to SSPCON2
ACKEN = 1, ACKDT = 0
ACKEN automatically cleared
TBRG
SDA
ACK
D0
SCL
TBRG
8
9
SSPIF
SSPIF set at
the end of receive
Cleared in
software
SSPIF set at the end
of Acknowledge sequence
Cleared in
software
Note: TBRG = one Baud Rate Generator period.
FIGURE 16-24:
STOP CONDITION RECEIVE OR TRANSMIT MODE
SCL = 1 for TBRG, followed by SDA = 1 for TBRG
after SDA sampled high. P bit (SSPSTAT<4>) is set.
Write to SSPCON2,
set PEN
PEN bit (SSPCON2<2>) is cleared by
hardware and the SSPIF bit is set
Falling edge of
9th clock
TBRG
SCL
SDA
ACK
P
TBRG
TBRG
TBRG
SCL brought high after TBRG
SDA asserted low before rising edge of clock
to setup Stop condition
Note: TBRG = one Baud Rate Generator period.
DS39636A-page 184
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
16.4.14
SLEEP OPERATION
16.4.17
2
While in Sleep mode, the I C module can receive
addresses or data and when an address match or
complete byte transfer occurs, wake the processor
from Sleep (if the MSSP interrupt is enabled).
16.4.15
EFFECTS OF A RESET
A Reset disables the MSSP module and terminates the
current transfer.
16.4.16
MULTI-MASTER MODE
In Multi-Master mode, the interrupt generation on the
detection of the Start and Stop conditions allows the
determination of when the bus is free. The Stop (P) and
Start (S) bits are cleared from a Reset or when the
MSSP module is disabled. Control of the I 2C bus may
be taken when the P bit (SSPSTAT<4>) is set, or the
bus is Idle, with both the S and P bits clear. When the
bus is busy, enabling the SSP interrupt will generate
the interrupt when the Stop condition occurs.
In multi-master operation, the SDA line must be
monitored for arbitration to see if the signal level is the
expected output level. This check is performed in
hardware with the result placed in the BCLIF bit.
The states where arbitration can be lost are:
•
•
•
•
•
Address Transfer
Data Transfer
A Start Condition
A Repeated Start Condition
An Acknowledge Condition
MULTI -MASTER COMMUNICATION,
BUS COLLISION AND BUS
ARBITRATION
Multi-Master mode support is achieved by bus arbitration. When the master outputs address/data bits onto
the SDA pin, arbitration takes place when the master
outputs a ‘1’ on SDA, by letting SDA float high and
another master asserts a ‘0’. When the SCL pin floats
high, data should be stable. If the expected data on
SDA is a ‘1’ and the data sampled on the SDA pin = 0,
then a bus collision has taken place. The master will set
the Bus Collision Interrupt Flag, BCLIF and reset the
I2C port to its Idle state (Figure 16-25).
If a transmit was in progress when the bus collision
occurred, the transmission is halted, the BF flag is
cleared, the SDA and SCL lines are deasserted and the
SSPBUF can be written to. When the user services the
bus collision Interrupt Service Routine and if the I2C
bus is free, the user can resume communication by
asserting a Start condition.
If a Start, Repeated Start, Stop or Acknowledge
condition was in progress when the bus collision
occurred, the condition is aborted, the SDA and SCL
lines are deasserted and the respective control bits in
the SSPCON2 register are cleared. When the user services the bus collision Interrupt Service Routine and if
the I2C bus is free, the user can resume communication
by asserting a Start condition.
The master will continue to monitor the SDA and SCL
pins. If a Stop condition occurs, the SSPIF bit will be set.
A write to the SSPBUF will start the transmission of
data at the first data bit regardless of where the
transmitter left off when the bus collision occurred.
In Multi-Master mode, the interrupt generation on the
detection of Start and Stop conditions allows the determination of when the bus is free. Control of the I2C bus
can be taken when the P bit is set in the SSPSTAT
register, or the bus is Idle and the S and P bits are
cleared.
FIGURE 16-25:
BUS COLLISION TIMING FOR TRANSMIT AND ACKNOWLEDGE
Data changes
while SCL = 0
SDA line pulled low
by another source
SDA released
by master
Sample SDA. While SCL is high,
data doesn’t match what is driven
by the master.
Bus collision has occurred.
SDA
SCL
Set bus collision
interrupt (BCLIF)
BCLIF
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 185
PIC18F2X1X/4X1X
16.4.17.1
Bus Collision During a Start
Condition
During a Start condition, a bus collision occurs if:
a)
b)
SDA or SCL are sampled low at the beginning of
the Start condition (Figure 16-26).
SCL is sampled low before SDA is asserted low
(Figure 16-27).
During a Start condition, both the SDA and the SCL
pins are monitored.
If the SDA pin is sampled low during this count, the
BRG is reset and the SDA line is asserted early
(Figure 16-28). If, however, a ‘1’ is sampled on the SDA
pin, the SDA pin is asserted low at the end of the BRG
count. The Baud Rate Generator is then reloaded and
counts down to 0; if the SCL pin is sampled as ‘0’
during this time, a bus collision does not occur. At the
end of the BRG count, the SCL pin is asserted low.
Note:
If the SDA pin is already low, or the SCL pin is already
low, then all of the following occur:
• the Start condition is aborted,
• the BCLIF flag is set and
• the MSSP module is reset to its Idle state
(Figure 16-26).
The Start condition begins with the SDA and SCL pins
deasserted. When the SDA pin is sampled high, the
Baud Rate Generator is loaded from SSPADD<6:0>
and counts down to 0. If the SCL pin is sampled low
while SDA is high, a bus collision occurs because it is
assumed that another master is attempting to drive a
data ‘1’ during the Start condition.
FIGURE 16-26:
The reason that bus collision is not a factor
during a Start condition is that no two bus
masters can assert a Start condition at the
exact same time. Therefore, one master
will always assert SDA before the other.
This condition does not cause a bus
collision because the two masters must be
allowed to arbitrate the first address
following the Start condition. If the address
is the same, arbitration must be allowed to
continue into the data portion, Repeated
Start or Stop conditions.
BUS COLLISION DURING START CONDITION (SDA ONLY)
SDA goes low before the SEN bit is set.
Set BCLIF,
S bit and SSPIF set because
SDA = 0, SCL = 1.
SDA
SCL
Set SEN, enable Start
condition if SDA = 1, SCL = 1
SEN cleared automatically because of bus collision.
SSP module reset into Idle state.
SEN
BCLIF
SDA sampled low before
Start condition. Set BCLIF.
S bit and SSPIF set because
SDA = 0, SCL = 1.
SSPIF and BCLIF are
cleared in software
S
SSPIF
SSPIF and BCLIF are
cleared in software
DS39636A-page 186
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
FIGURE 16-27:
BUS COLLISION DURING START CONDITION (SCL = 0)
SDA = 0, SCL = 1
TBRG
TBRG
SDA
Set SEN, enable Start
sequence if SDA = 1, SCL = 1
SCL
SCL = 0 before SDA = 0,
bus collision occurs. Set BCLIF.
SEN
SCL = 0 before BRG time-out,
bus collision occurs. Set BCLIF.
BCLIF
Interrupt cleared
in software
S
‘0’
‘0’
SSPIF
‘0’
‘0’
FIGURE 16-28:
BRG RESET DUE TO SDA ARBITRATION DURING START CONDITION
SDA = 0, SCL = 1
Set S
Less than TBRG
SDA
Set SSPIF
TBRG
SDA pulled low by other master.
Reset BRG and assert SDA.
SCL
S
SCL pulled low after BRG
time-out
SEN
BCLIF
Set SEN, enable START
sequence if SDA = 1, SCL = 1
‘0’
S
SSPIF
SDA = 0, SCL = 1,
set SSPIF
 2004 Microchip Technology Inc.
Preliminary
Interrupts cleared
in software
DS39636A-page 187
PIC18F2X1X/4X1X
16.4.17.2
Bus Collision During a Repeated
Start Condition
If SDA is low, a bus collision has occurred (i.e., another
master is attempting to transmit a data ‘0’, Figure 16-29).
If SDA is sampled high, the BRG is reloaded and begins
counting. If SDA goes from high-to-low before the BRG
times out, no bus collision occurs because no two
masters can assert SDA at exactly the same time.
During a Repeated Start condition, a bus collision
occurs if:
a)
b)
A low level is sampled on SDA when SCL goes
from low level to high level.
SCL goes low before SDA is asserted low,
indicating that another master is attempting to
transmit a data ‘1’.
If SCL goes from high-to-low before the BRG times out
and SDA has not already been asserted, a bus collision
occurs. In this case, another master is attempting to
transmit a data ‘1’ during the Repeated Start condition,
see Figure 16-30.
When the user deasserts SDA and the pin is allowed to
float high, the BRG is loaded with SSPADD<6:0> and
counts down to 0. The SCL pin is then deasserted and
when sampled high, the SDA pin is sampled.
FIGURE 16-29:
If, at the end of the BRG time-out, both SCL and SDA
are still high, the SDA pin is driven low and the BRG is
reloaded and begins counting. At the end of the count,
regardless of the status of the SCL pin, the SCL pin is
driven low and the Repeated Start condition is
complete.
BUS COLLISION DURING A REPEATED START CONDITION (CASE 1)
SDA
SCL
Sample SDA when SCL goes high.
If SDA = 0, set BCLIF and release SDA and SCL.
RSEN
BCLIF
Cleared in software
‘0’
S
‘0’
SSPIF
FIGURE 16-30:
BUS COLLISION DURING REPEATED START CONDITION (CASE 2)
TBRG
TBRG
SDA
SCL
BCLIF
SCL goes low before SDA,
set BCLIF. Release SDA and SCL.
Interrupt cleared
in software
RSEN
‘0’
S
SSPIF
DS39636A-page 188
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
16.4.17.3
Bus Collision During a Stop
Condition
The Stop condition begins with SDA asserted low.
When SDA is sampled low, the SCL pin is allowed to
float. When the pin is sampled high (clock arbitration),
the Baud Rate Generator is loaded with SSPADD<6:0>
and counts down to 0. After the BRG times out, SDA is
sampled. If SDA is sampled low, a bus collision has
occurred. This is due to another master attempting to
drive a data ‘0’ (Figure 16-31). If the SCL pin is
sampled low before SDA is allowed to float high, a bus
collision occurs. This is another case of another master
attempting to drive a data ‘0’ (Figure 16-32).
Bus collision occurs during a Stop condition if:
a)
b)
After the SDA pin has been deasserted and
allowed to float high, SDA is sampled low after
the BRG has timed out.
After the SCL pin is deasserted, SCL is sampled
low before SDA goes high.
FIGURE 16-31:
BUS COLLISION DURING A STOP CONDITION (CASE 1)
TBRG
TBRG
TBRG
SDA sampled
low after TBRG,
set BCLIF
SDA
SDA asserted low
SCL
PEN
BCLIF
P
‘0’
SSPIF
‘0’
FIGURE 16-32:
BUS COLLISION DURING A STOP CONDITION (CASE 2)
TBRG
TBRG
TBRG
SDA
SCL goes low before SDA goes high,
set BCLIF
Assert SDA
SCL
PEN
BCLIF
P
‘0’
SSPIF
‘0’
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 189
PIC18F2X1X/4X1X
NOTES:
DS39636A-page 190
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
17.0
ENHANCED UNIVERSAL
SYNCHRONOUS RECEIVER
TRANSMITTER (EUSART)
The pins of the Enhanced USART are multiplexed with
PORTC. In order to configure RC6/TX/CK and
RC7/RX/DT as a USART:
The Enhanced Universal Synchronous Asynchronous
Receiver Transmitter (EUSART) module is one of the
two serial I/O modules. (Generically, the USART is also
known as a Serial Communications Interface or SCI.)
The EUSART can be configured as a full-duplex
asynchronous system that can communicate with
peripheral devices, such as CRT terminals and
personal computers. It can also be configured as a halfduplex synchronous system that can communicate
with peripheral devices, such as A/D or D/A integrated
circuits, serial EEPROMs, etc.
The Enhanced USART module implements additional
features, including automatic baud rate detection and
calibration, automatic wake-up on Sync Break reception and 12-bit Break character transmit. These make it
ideally suited for use in Local Interconnect Network bus
(LIN bus) systems.
• bit SPEN (RCSTA<7>) must be set (= 1)
• bit TRISC<7> must be set (= 1)
• bit TRISC<6> must be set (= 1)
Note:
The EUSART control will automatically
reconfigure the pin from input to output as
needed.
The operation of the Enhanced USART module is
controlled through three registers:
• Transmit Status and Control (TXSTA)
• Receive Status and Control (RCSTA)
• Baud Rate Control (BAUDCON)
These are detailed on the following pages in
Register 17-1, Register 17-2 and Register 17-3,
respectively.
The EUSART can be configured in the following
modes:
• Asynchronous (full duplex) with:
- Auto-wake-up on character reception
- Auto-baud calibration
- 12-bit Break character transmission
• Synchronous – Master (half duplex) with
selectable clock polarity
• Synchronous – Slave (half duplex) with selectable
clock polarity
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 191
PIC18F2X1X/4X1X
REGISTER 17-1:
TXSTA: TRANSMIT STATUS AND CONTROL REGISTER
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R-1
R/W-0
CSRC
TX9
TXEN
SYNC
SENDB
BRGH
TRMT
TX9D
bit 7
bit 0
bit 7
CSRC: Clock Source Select bit
Asynchronous mode:
Don’t care.
Synchronous mode:
1 = Master mode (clock generated internally from BRG)
0 = Slave mode (clock from external source)
bit 6
TX9: 9-bit Transmit Enable bit
1 = Selects 9-bit transmission
0 = Selects 8-bit transmission
bit 5
TXEN: Transmit Enable bit
1 = Transmit enabled
0 = Transmit disabled
Note:
SREN/CREN overrides TXEN in Sync mode.
bit 4
SYNC: EUSART Mode Select bit
1 = Synchronous mode
0 = Asynchronous mode
bit 3
SENDB: Send Break Character bit
Asynchronous mode:
1 = Send Sync Break on next transmission (cleared by hardware upon completion)
0 = Sync Break transmission completed
Synchronous mode:
Don’t care.
bit 2
BRGH: High Baud Rate Select bit
Asynchronous mode:
1 = High speed
0 = Low speed
Synchronous mode:
Unused in this mode.
bit 1
TRMT: Transmit Shift Register Status bit
1 = TSR empty
0 = TSR full
bit 0
TX9D: 9th bit of Transmit Data
Can be address/data bit or a parity bit.
Legend:
DS39636A-page 192
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
Preliminary
x = Bit is unknown
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
REGISTER 17-2:
RCSTA: RECEIVE STATUS AND CONTROL REGISTER
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R-0
R-0
R-x
SPEN
RX9
SREN
CREN
ADDEN
FERR
OERR
RX9D
bit 7
bit 0
bit 7
SPEN: Serial Port Enable bit
1 = Serial port enabled (configures RX/DT and TX/CK pins as serial port pins)
0 = Serial port disabled (held in Reset)
bit 6
RX9: 9-bit Receive Enable bit
1 = Selects 9-bit reception
0 = Selects 8-bit reception
bit 5
SREN: Single Receive Enable bit
Asynchronous mode:
Don’t care.
Synchronous mode – Master:
1 = Enables single receive
0 = Disables single receive
This bit is cleared after reception is complete.
Synchronous mode – Slave:
Don’t care.
bit 4
CREN: Continuous Receive Enable bit
Asynchronous mode:
1 = Enables receiver
0 = Disables receiver
Synchronous mode:
1 = Enables continuous receive until enable bit CREN is cleared (CREN overrides SREN)
0 = Disables continuous receive
bit 3
ADDEN: Address Detect Enable bit
Asynchronous mode 9-bit (RX9 = 1):
1 = Enables address detection, enables interrupt and loads the receive buffer when RSR<8>
is set
0 = Disables address detection, all bytes are received and ninth bit can be used as parity bit
Asynchronous mode 9-bit (RX9 = 0):
Don’t care.
bit 2
FERR: Framing Error bit
1 = Framing error (can be updated by reading RCREG register and receiving next valid byte)
0 = No framing error
bit 1
OERR: Overrun Error bit
1 = Overrun error (can be cleared by clearing bit CREN)
0 = No overrun error
bit 0
RX9D: 9th bit of Received Data
This can be address/data bit or a parity bit and must be calculated by user firmware.
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
 2004 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS39636A-page 193
PIC18F2X1X/4X1X
REGISTER 17-3:
BAUDCON: BAUD RATE CONTROL REGISTER
R/W-0
R-1
U-0
R/W-0
R/W-0
U-0
R/W-0
R/W-0
ABDOVF
RCIDL
—
SCKP
BRG16
—
WUE
ABDEN
bit 7
bit 0
bit 7
ABDOVF: Auto-Baud Acquisition Rollover Status bit
1 = A BRG rollover has occurred during Auto-Baud Rate Detect mode
(must be cleared in software)
0 = No BRG rollover has occurred
bit 6
RCIDL: Receive Operation Idle Status bit
1 = Receive operation is Idle
0 = Receive operation is active
bit 5
Unimplemented: Read as ‘0’
bit 4
SCKP: Synchronous Clock Polarity Select bit
Asynchronous mode:
Unused in this mode.
Synchronous mode:
1 = Idle state for clock (CK) is a high level
0 = Idle state for clock (CK) is a low level
bit 3
BRG16: 16-bit Baud Rate Register Enable bit
1 = 16-bit Baud Rate Generator – SPBRGH and SPBRG
0 = 8-bit Baud Rate Generator – SPBRG only (Compatible mode), SPBRGH value ignored
bit 2
Unimplemented: Read as ‘0’
bit 1
WUE: Wake-up Enable bit
Asynchronous mode:
1 = EUSART will continue to sample the RX pin – interrupt generated on falling edge; bit
cleared in hardware on following rising edge
0 = RX pin not monitored or rising edge detected
Synchronous mode:
Unused in this mode.
bit 0
ABDEN: Auto-Baud Detect Enable bit
Asynchronous mode:
1 = Enable baud rate measurement on the next character. Requires reception of a Sync field
(55h); cleared in hardware upon completion
0 = Baud rate measurement disabled or completed
Synchronous mode:
Unused in this mode.
Legend:
DS39636A-page 194
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
Preliminary
x = Bit is unknown
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
17.1
Baud Rate Generator (BRG)
The BRG is a dedicated 8-bit or 16-bit generator that
supports both the Asynchronous and Synchronous
modes of the EUSART. By default, the BRG operates
in 8-bit mode; setting the BRG16 bit (BAUDCON<3>)
selects 16-bit mode.
The SPBRGH:SPBRG register pair controls the period
of a free running timer. In Asynchronous mode, bits
BRGH (TXSTA<2>) and BRG16 (BAUDCON<3>) also
control the baud rate. In Synchronous mode, BRGH is
ignored. Table 17-1 shows the formula for computation
of the baud rate for different EUSART modes which
only apply in Master mode (internally generated clock).
Given the desired baud rate and FOSC, the nearest
integer value for the SPBRGH:SPBRG registers can be
calculated using the formulas in Table 17-1. From this,
the error in baud rate can be determined. An example
calculation is shown in Example 17-1. Typical baud
rates and error values for the various Asynchronous
modes are shown in Table 17-2. It may be
TABLE 17-1:
advantageous to use the high baud rate (BRGH = 1) or
the 16-bit BRG to reduce the baud rate error, or
achieve a slow baud rate for a fast oscillator frequency.
Writing a new value to the SPBRGH:SPBRG registers
causes the BRG timer to be reset (or cleared). This
ensures the BRG does not wait for a timer overflow
before outputting the new baud rate.
17.1.1
OPERATION IN POWER MANAGED
MODES
The device clock is used to generate the desired baud
rate. When one of the power managed modes is
entered, the new clock source may be operating at a
different frequency. This may require an adjustment to
the value in the SPBRG register pair.
17.1.2
SAMPLING
The data on the RX pin is sampled three times by a
majority detect circuit to determine if a high or a low
level is present at the RX pin.
BAUD RATE FORMULAS
Configuration Bits
BRG/EUSART Mode
Baud Rate Formula
8-bit/Asynchronous
FOSC/[64 (n + 1)]
SYNC
BRG16
BRGH
0
0
0
0
0
1
8-bit/Asynchronous
0
1
0
16-bit/Asynchronous
0
1
1
16-bit/Asynchronous
1
0
x
8-bit/Synchronous
1
1
x
16-bit/Synchronous
FOSC/[16 (n + 1)]
FOSC/[4 (n + 1)]
Legend: x = Don’t care, n = value of SPBRGH:SPBRG register pair
EXAMPLE 17-1:
CALCULATING BAUD RATE ERROR
For a device with FOSC of 16 MHz, desired baud rate of 9600, Asynchronous mode, 8-bit BRG:
Desired Baud Rate
= FOSC/(64 ([SPBRGH:SPBRG] + 1))
Solving for SPBRGH:SPBRG:
X
= ((FOSC/Desired Baud Rate)/64) – 1
= ((16000000/9600)/64) – 1
= [25.042] = 25
Calculated Baud Rate = 16000000/(64 (25 + 1))
= 9615
Error
= (Calculated Baud Rate – Desired Baud Rate)/Desired Baud Rate
= (9615 – 9600)/9600 = 0.16%
TABLE 17-2:
Name
REGISTERS ASSOCIATED WITH BAUD RATE GENERATOR
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Reset Values
on page
Bit 0
TXSTA
CSRC
TX9
TXEN
SYNC
SENDB
BRGH
TRMT
TX9D
51
RCSTA
SPEN
RX9
SREN
CREN
ADDEN
FERR
OERR
RX9D
51
RCIDL
—
SCKP
BRG16
—
WUE
ABDEN
51
BAUDCON ABDOVF
SPBRGH
EUSART Baud Rate Generator Register, High Byte
51
SPBRG
EUSART Baud Rate Generator Register, Low Byte
51
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used by the BRG.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 195
PIC18F2X1X/4X1X
TABLE 17-3:
BAUD RATES FOR ASYNCHRONOUS MODES
SYNC = 0, BRGH = 0, BRG16 = 0
BAUD
RATE
(K)
FOSC = 40.000 MHz
FOSC = 20.000 MHz
(decimal)
Actual
Rate
(K)
%
Error
—
—
—
—
—
1.221
2.441
1.73
255
Actual
Rate
(K)
%
Error
0.3
1.2
—
—
2.4
SPBRG
value
FOSC = 10.000 MHz
(decimal)
Actual
Rate
(K)
%
Error
—
1.73
—
255
—
1.202
2.404
0.16
129
SPBRG
value
FOSC = 8.000 MHz
(decimal)
Actual
Rate
(K)
%
Error
—
0.16
—
129
—
1201
—
-0.16
—
103
2.404
0.16
64
2403
-0.16
51
SPBRG
value
SPBRG
value
(decimal)
9.6
9.615
0.16
64
9.766
1.73
31
9.766
1.73
15
9615
-0.16
12
19.2
19.531
1.73
31
19.531
1.73
15
19.531
1.73
7
—
—
—
57.6
56.818
-1.36
10
62.500
8.51
4
52.083
-9.58
2
—
—
—
115.2
125.000
8.51
4
104.167
-9.58
2
78.125
-32.18
1
—
—
—
SYNC = 0, BRGH = 0, BRG16 = 0
BAUD
RATE
(K)
FOSC = 4.000 MHz
Actual
Rate
(K)
%
Error
0.3
0.300
0.16
1.2
1.202
0.16
FOSC = 2.000 MHz
Actual
Rate
(K)
%
Error
207
300
-0.16
51
1201
-0.16
SPBRG
value
(decimal)
FOSC = 1.000 MHz
Actual
Rate
(K)
%
Error
103
300
-0.16
51
25
1201
-0.16
12
SPBRG
value
(decimal)
SPBRG
value
(decimal)
2.4
2.404
0.16
25
2403
-0.16
12
—
—
—
9.6
8.929
-6.99
6
—
—
—
—
—
—
19.2
20.833
8.51
2
—
—
—
—
—
—
57.6
62.500
8.51
0
—
—
—
—
—
—
115.2
62.500
-45.75
0
—
—
—
—
—
—
SYNC = 0, BRGH = 1, BRG16 = 0
BAUD
RATE
(K)
0.3
1.2
FOSC = 40.000 MHz
Actual
Rate
(K)
%
Error
—
—
—
—
FOSC = 20.000 MHz
(decimal)
Actual
Rate
(K)
%
Error
—
—
—
—
—
—
SPBRG
value
SPBRG
value
FOSC = 10.000 MHz
(decimal)
Actual
Rate
(K)
%
Error
—
—
—
—
FOSC = 8.000 MHz
SPBRG
value
(decimal)
Actual
Rate
(K)
%
Error
SPBRG
value
—
—
—
—
—
—
—
—
—
—
(decimal)
2.4
—
—
—
—
—
—
2.441
1.73
255
2403
-0.16
207
9.6
9.766
1.73
255
9.615
0.16
129
9.615
0.16
64
9615
-0.16
51
25
19.2
19.231
0.16
129
19.231
0.16
64
19.531
1.73
31
19230
-0.16
57.6
58.140
0.94
42
56.818
-1.36
21
56.818
-1.36
10
55555
3.55
8
115.2
113.636
-1.36
21
113.636
-1.36
10
125.000
8.51
4
—
—
—
SYNC = 0, BRGH = 1, BRG16 = 0
BAUD
RATE
(K)
FOSC = 4.000 MHz
FOSC = 2.000 MHz
(decimal)
Actual
Rate
(K)
%
Error
—
—
—
0.16
207
1201
2.404
0.16
103
9.615
0.16
25
19.2
19.231
0.16
57.6
62.500
115.2
125.000
(decimal)
Actual
Rate
(K)
%
Error
—
300
-0.16
207
-0.16
103
1201
-0.16
51
2403
-0.16
51
2403
-0.16
25
9615
-0.16
12
—
—
—
12
—
—
—
—
—
—
8.51
3
—
—
—
—
—
—
8.51
1
—
—
—
—
—
—
Actual
Rate
(K)
%
Error
0.3
—
—
1.2
1.202
2.4
9.6
DS39636A-page 196
FOSC = 1.000 MHz
SPBRG
value
SPBRG
value
Preliminary
SPBRG
value
(decimal)
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
TABLE 17-3:
BAUD RATES FOR ASYNCHRONOUS MODES (CONTINUED)
SYNC = 0, BRGH = 0, BRG16 = 1
BAUD
RATE
(K)
FOSC = 40.000 MHz
FOSC = 20.000 MHz
(decimal)
Actual
Rate
(K)
%
Error
0.00
0.02
8332
2082
0.300
1.200
2.402
0.06
1040
Actual
Rate
(K)
%
Error
0.3
1.2
0.300
1.200
2.4
SPBRG
value
FOSC = 10.000 MHz
(decimal)
Actual
Rate
(K)
%
Error
0.02
-0.03
4165
1041
0.300
1.200
2.399
-0.03
520
SPBRG
value
FOSC = 8.000 MHz
(decimal)
Actual
Rate
(K)
%
Error
0.02
-0.03
2082
520
300
1201
-0.04
-0.16
1665
415
2.404
0.16
259
2403
-0.16
207
SPBRG
value
SPBRG
value
(decimal)
9.6
9.615
0.16
259
9.615
0.16
129
9.615
0.16
64
9615
-0.16
51
19.2
19.231
0.16
129
19.231
0.16
64
19.531
1.73
31
19230
-0.16
25
57.6
58.140
0.94
42
56.818
-1.36
21
56.818
-1.36
10
55555
3.55
8
115.2
113.636
-1.36
21
113.636
-1.36
10
125.000
8.51
4
—
—
—
SYNC = 0, BRGH = 0, BRG16 = 1
BAUD
RATE
(K)
FOSC
= 4.000 MHz
(decimal)
Actual
Rate
(K)
%
Error
832
300
-0.16
0.16
207
1201
0.16
103
2403
Actual
Rate
(K)
%
Error
0.300
0.04
1.2
1.202
2.4
2.404
0.3
FOSC = 2.000 MHz
SPBRG
value
FOSC = 1.000 MHz
(decimal)
Actual
Rate
(K)
%
Error
415
300
-0.16
-0.16
103
1201
-0.16
51
-0.16
51
2403
-0.16
25
SPBRG
value
SPBRG
value
(decimal)
207
9.6
9.615
0.16
25
9615
-0.16
12
—
—
—
19.2
19.231
0.16
12
—
—
—
—
—
—
57.6
62.500
8.51
3
—
—
—
—
—
—
115.2
125.000
8.51
1
—
—
—
—
—
—
SYNC = 0, BRGH = 1, BRG16 = 1 or SYNC = 1, BRG16 = 1
BAUD
RATE
(K)
FOSC = 40.000 MHz
FOSC = 20.000 MHz
(decimal)
Actual
Rate
(K)
%
Error
0.00
33332
0.300
0.00
8332
1.200
2.400
0.02
4165
9.606
0.06
1040
19.2
19.193
-0.03
520
57.6
57.803
0.35
172
115.2
114.943
-0.22
86
116.279
Actual
Rate
(K)
%
Error
0.3
0.300
1.2
1.200
2.4
9.6
SPBRG
value
FOSC = 10.000 MHz
(decimal)
Actual
Rate
(K)
%
Error
0.00
16665
0.300
0.00
0.02
4165
1.200
0.02
2.400
0.02
2082
2.402
9.596
-0.03
520
19.231
0.16
57.471
-0.22
0.94
FOSC = 8.000 MHz
Actual
Rate
(K)
%
Error
8332
300
-0.01
6665
2082
1200
-0.04
1665
0.06
1040
2400
-0.04
832
9.615
0.16
259
9615
-0.16
207
259
19.231
0.16
129
19230
-0.16
103
86
58.140
0.94
42
57142
0.79
34
42
113.636
-1.36
21
117647
-2.12
16
SPBRG
value
SPBRG
value
(decimal)
SPBRG
value
(decimal)
SYNC = 0, BRGH = 1, BRG16 = 1 or SYNC = 1, BRG16 = 1
BAUD
RATE
(K)
FOSC = 4.000 MHz
Actual
Rate
(K)
%
Error
0.3
0.300
0.01
1.2
1.200
0.04
FOSC = 2.000 MHz
(decimal)
Actual
Rate
(K)
%
Error
3332
300
-0.04
832
1201
SPBRG
value
FOSC = 1.000 MHz
(decimal)
Actual
Rate
(K)
%
Error
1665
300
-0.04
832
-0.16
415
1201
-0.16
207
SPBRG
value
SPBRG
value
(decimal)
2.4
2.404
0.16
415
2403
-0.16
207
2403
-0.16
103
9.6
9.615
0.16
103
9615
-0.16
51
9615
-0.16
25
19.2
19.231
0.16
51
19230
-0.16
25
19230
-0.16
12
57.6
58.824
2.12
16
55555
3.55
8
—
—
—
115.2
111.111
-3.55
8
—
—
—
—
—
—
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 197
PIC18F2X1X/4X1X
17.1.3
AUTO-BAUD RATE DETECT
The Enhanced USART module supports the automatic
detection and calibration of baud rate. This feature is
active only in Asynchronous mode and while the WUE
bit is clear.
Note 1: If the WUE bit is set with the ABDEN bit,
Auto-Baud Rate Detection will occur on
the byte following the Break character.
2: It is up to the user to determine that the
incoming character baud rate is within the
range of the selected BRG clock source.
Some combinations of oscillator frequency
and EUSART baud rates are not possible
due to bit error rates. Overall system
timing and communication baud rates
must be taken into consideration when
using the Auto-Baud Rate Detection
feature.
The automatic baud rate measurement sequence
(Figure 17-1) begins whenever a Start bit is received
and the ABDEN bit is set. The calculation is
self-averaging.
In the Auto-Baud Rate Detect (ABD) mode, the clock to
the BRG is reversed. Rather than the BRG clocking the
incoming RX signal, the RX signal is timing the BRG. In
ABD mode, the internal Baud Rate Generator is used
as a counter to time the bit period of the incoming serial
byte stream.
Once the ABDEN bit is set, the state machine will clear
the BRG and look for a Start bit. The Auto-Baud Rate
Detect must receive a byte with the value 55h (ASCII
“U”, which is also the LIN bus Sync character) in order to
calculate the proper bit rate. The measurement is taken
over both a low and a high bit time in order to minimize
any effects caused by asymmetry of the incoming signal.
After a Start bit, the SPBRG begins counting up, using
the preselected clock source on the first rising edge of
RX. After eight bits on the RX pin or the fifth rising edge,
an accumulated value totalling the proper BRG period is
left in the SPBRGH:SPBRG register pair. Once the 5th
edge is seen (this should correspond to the Stop bit), the
ABDEN bit is automatically cleared.
If a rollover of the BRG occurs (an overflow from FFFFh
to 0000h), the event is trapped by the ABDOVF status
bit (BAUDCON<7>). It is set in hardware by BRG rollovers and can be set or cleared by the user in software.
ABD mode remains active after rollover events and the
ABDEN bit remains set (Figure 17-2).
TABLE 17-4:
BRG16
BRGH
BRG COUNTER
CLOCK RATES
BRG Counter Clock
0
0
FOSC/512
0
1
FOSC/128
1
0
FOSC/128
1
1
FOSC/32
Note:
17.1.3.1
During the ABD sequence, SPBRG and
SPBRGH are both used as a 16-bit
counter, independent of BRG16 setting.
ABD and EUSART Transmission
Since the BRG clock is reversed during ABD acquisition, the EUSART transmitter cannot be used during
ABD. This means that whenever the ABDEN bit is set,
TXREG cannot be written to. Users should also ensure
that ABDEN does not become set during a transmit
sequence. Failing to do this may result in unpredictable
EUSART operation.
While calibrating the baud rate period, the BRG
registers are clocked at 1/8th the preconfigured clock
rate. Note that the BRG clock will be configured by the
BRG16 and BRGH bits. Independent of the BRG16 bit
setting, both the SPBRG and SPBRGH will be used as
a 16-bit counter. This allows the user to verify that no
carry occurred for 8-bit modes by checking for 00h in
the SPBRGH register. Refer to Table 17-4 for counter
clock rates to the BRG.
While the ABD sequence takes place, the EUSART
state machine is held in Idle. The RCIF interrupt is set
once the fifth rising edge on RX is detected. The value
in the RCREG needs to be read to clear the RCIF
interrupt. The contents of RCREG should be discarded.
DS39636A-page 198
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
FIGURE 17-1:
BRG Value
AUTOMATIC BAUD RATE CALCULATION
XXXXh
RX pin
0000h
001Ch
Start
Edge #1
Bit 1
Bit 0
Edge #2
Bit 3
Bit 2
Edge #3
Bit 5
Bit 4
Edge #4
Bit 7
Bit 6
Edge #5
Stop Bit
BRG Clock
Auto-Cleared
Set by User
ABDEN bit
RCIF bit
(Interrupt)
Read
RCREG
SPBRG
XXXXh
1Ch
SPBRGH
XXXXh
00h
Note: The ABD sequence requires the EUSART module to be configured in Asynchronous mode and WUE = 0.
FIGURE 17-2:
BRG OVERFLOW SEQUENCE
BRG Clock
ABDEN bit
RX pin
Start
Bit 0
ABDOVF bit
FFFFh
BRG Value
XXXXh
 2004 Microchip Technology Inc.
0000h
0000h
Preliminary
DS39636A-page 199
PIC18F2X1X/4X1X
17.2
EUSART Asynchronous Mode
Once the TXREG register transfers the data to the TSR
register (occurs in one TCY), the TXREG register is empty
and the TXIF flag bit (PIR1<4>) is set. This interrupt can
be enabled or disabled by setting or clearing the interrupt
enable bit, TXIE (PIE1<4>). TXIF will be set regardless of
the state of TXIE; it cannot be cleared in software. TXIF
is also not cleared immediately upon loading TXREG, but
becomes valid in the second instruction cycle following
the load instruction. Polling TXIF immediately following a
load of TXREG will return invalid results.
The Asynchronous mode of operation is selected by
clearing the SYNC bit (TXSTA<4>). In this mode, the
EUSART uses standard Non-Return-to-Zero (NRZ)
format (one Start bit, eight or nine data bits and one Stop
bit). The most common data format is 8 bits. An on-chip
dedicated 8-bit/16-bit Baud Rate Generator can be used
to derive standard baud rate frequencies from the
oscillator.
The EUSART transmits and receives the LSb first. The
EUSART’s transmitter and receiver are functionally
independent but use the same data format and baud
rate. The Baud Rate Generator produces a clock, either
x16 or x64 of the bit shift rate depending on the BRGH
and BRG16 bits (TXSTA<2> and BAUDCON<3>). Parity
is not supported by the hardware but can be
implemented in software and stored as the 9th data bit.
While TXIF indicates the status of the TXREG register,
another bit, TRMT (TXSTA<1>), shows the status of
the TSR register. TRMT is a read-only bit which is set
when the TSR register is empty. No interrupt logic is
tied to this bit so the user has to poll this bit in order to
determine if the TSR register is empty.
Note 1: The TSR register is not mapped in data
memory so it is not available to the user.
When operating in Asynchronous mode, the EUSART
module consists of the following important elements:
•
•
•
•
•
•
•
2: Flag bit TXIF is set when enable bit TXEN
is set.
Baud Rate Generator
Sampling Circuit
Asynchronous Transmitter
Asynchronous Receiver
Auto-Wake-up on Sync Break Character
12-bit Break Character Transmit
Auto-Baud Rate Detection
17.2.1
To set up an Asynchronous Transmission:
1.
2.
EUSART ASYNCHRONOUS
TRANSMITTER
3.
4.
The EUSART transmitter block diagram is shown in
Figure 17-3. The heart of the transmitter is the Transmit
(Serial) Shift Register (TSR). The Shift register obtains
its data from the Read/Write Transmit Buffer register,
TXREG. The TXREG register is loaded with data in
software. The TSR register is not loaded until the Stop
bit has been transmitted from the previous load. As
soon as the Stop bit is transmitted, the TSR is loaded
with new data from the TXREG register (if available).
FIGURE 17-3:
5.
6.
7.
8.
Initialize the SPBRGH:SPBRG registers for the
appropriate baud rate. Set or clear the BRGH
and BRG16 bits, as required, to achieve the
desired baud rate.
Enable the asynchronous serial port by clearing
bit SYNC and setting bit SPEN.
If interrupts are desired, set enable bit TXIE.
If 9-bit transmission is desired, set transmit bit
TX9. Can be used as address/data bit.
Enable the transmission by setting bit TXEN
which will also set bit TXIF.
If 9-bit transmission is selected, the ninth bit
should be loaded in bit TX9D.
Load data to the TXREG register (starts
transmission).
If using interrupts, ensure that the GIE and PEIE
bits in the INTCON register (INTCON<7:6>) are
set.
EUSART TRANSMIT BLOCK DIAGRAM
Data Bus
TXIF
TXREG Register
TXIE
8
MSb
(8)
LSb
• • •
Pin Buffer
and Control
0
TSR Register
TX pin
Interrupt
TXEN
Baud Rate CLK
TRMT
BRG16
SPBRGH
SPBRG
Baud Rate Generator
DS39636A-page 200
SPEN
TX9
TX9D
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
FIGURE 17-4:
ASYNCHRONOUS TRANSMISSION
Write to TXREG
Word 1
BRG Output
(Shift Clock)
TX
(pin)
Start bit
bit 0
bit 1
bit 7/8
Stop bit
Word 1
TXIF bit
(Transmit Buffer
Reg. Empty Flag)
1 TCY
Word 1
Transmit Shift Reg
TRMT bit
(Transmit Shift
Reg. Empty Flag)
FIGURE 17-5:
ASYNCHRONOUS TRANSMISSION (BACK TO BACK)
Write to TXREG
Word 1
Word 2
BRG Output
(Shift Clock)
TX
(pin)
Start bit
bit 0
bit 1
1 TCY
TXIF bit
(Interrupt Reg. Flag)
bit 7/8
Stop bit
Start bit
bit 0
Word 2
Word 1
1 TCY
Word 1
Transmit Shift Reg.
TRMT bit
(Transmit Shift
Reg. Empty Flag)
Word 2
Transmit Shift Reg.
Note: This timing diagram shows two consecutive transmissions.
TABLE 17-5:
Name
REGISTERS ASSOCIATED WITH ASYNCHRONOUS TRANSMISSION
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
Values
on page
INTCON
GIE/GIEH PEIE/GIEL
TMR0IE
INT0IE
RBIE
TMR0IF
INT0IF
RBIF
49
PIR1
PSPIF(1)
ADIF
RCIF
TXIF
SSPIF
CCP1IF
TMR2IF
TMR1IF
52
PIE1
PSPIE(1)
ADIE
RCIE
TXIE
SSPIE
CCP1IE
TMR2IE
TMR1IE
52
IPR1
PSPIP(1)
ADIP
RCIP
TXIP
SSPIP
CCP1IP
TMR2IP
TMR1IP
52
SPEN
RX9
SREN
CREN
ADDEN
FERR
OERR
RX9D
RCSTA
TXREG
TXSTA
BAUDCON
EUSART Transmit Register
51
51
CSRC
TX9
TXEN
SYNC
SENDB
BRGH
TRMT
TX9D
51
ABDOVF
RCIDL
—
SCKP
BRG16
—
WUE
ABDEN
51
SPBRGH
EUSART Baud Rate Generator Register, High Byte
51
SPBRG
EUSART Baud Rate Generator Register, Low Byte
51
Legend: — = unimplemented locations read as ‘0’. Shaded cells are not used for asynchronous transmission.
Note 1: These bits are unimplemented on 28-pin devices and read as ‘0’.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 201
PIC18F2X1X/4X1X
17.2.2
EUSART ASYNCHRONOUS
RECEIVER
17.2.3
The receiver block diagram is shown in Figure 17-6.
The data is received on the RX pin and drives the data
recovery block. The data recovery block is actually a
high-speed shifter operating at x16 times the baud rate,
whereas the main receive serial shifter operates at the
bit rate or at FOSC. This mode would typically be used
in RS-232 systems.
This mode would typically be used in RS-485 systems.
To set up an Asynchronous Reception with Address
Detect Enable:
1.
Initialize the SPBRGH:SPBRG registers for the
appropriate baud rate. Set or clear the BRGH
and BRG16 bits, as required, to achieve the
desired baud rate.
2. Enable the asynchronous serial port by clearing
the SYNC bit and setting the SPEN bit.
3. If interrupts are required, set the RCEN bit and
select the desired priority level with the RCIP bit.
4. Set the RX9 bit to enable 9-bit reception.
5. Set the ADDEN bit to enable address detect.
6. Enable reception by setting the CREN bit.
7. The RCIF bit will be set when reception is
complete. The interrupt will be Acknowledged if
the RCIE and GIE bits are set.
8. Read the RCSTA register to determine if any
error occurred during reception, as well as read
bit 9 of data (if applicable).
9. Read RCREG to determine if the device is being
addressed.
10. If any error occurred, clear the CREN bit.
11. If the device has been addressed, clear the
ADDEN bit to allow all received data into the
receive buffer and interrupt the CPU.
To set up an Asynchronous Reception:
1.
Initialize the SPBRGH:SPBRG registers for the
appropriate baud rate. Set or clear the BRGH
and BRG16 bits, as required, to achieve the
desired baud rate.
2. Enable the asynchronous serial port by clearing
bit SYNC and setting bit SPEN.
3. If interrupts are desired, set enable bit RCIE.
4. If 9-bit reception is desired, set bit RX9.
5. Enable the reception by setting bit CREN.
6. Flag bit RCIF will be set when reception is
complete and an interrupt will be generated if
enable bit RCIE was set.
7. Read the RCSTA register to get the 9th bit (if
enabled) and determine if any error occurred
during reception.
8. Read the 8-bit received data by reading the
RCREG register.
9. If any error occurred, clear the error by clearing
enable bit CREN.
10. If using interrupts, ensure that the GIE and PEIE
bits in the INTCON register (INTCON<7:6>) are
set.
FIGURE 17-6:
SETTING UP 9-BIT MODE WITH
ADDRESS DETECT
EUSART RECEIVE BLOCK DIAGRAM
CREN
OERR
FERR
x64 Baud Rate CLK
BRG16
SPBRGH
SPBRG
Baud Rate Generator
÷ 64
or
÷ 16
or
÷4
RSR Register
MSb
Stop
(8)
7
• • •
1
LSb
0
Start
RX9
Pin Buffer
and Control
Data
Recovery
RX9D
RX
RCREG Register
FIFO
SPEN
8
Interrupt
RCIF
Data Bus
RCIE
DS39636A-page 202
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
FIGURE 17-7:
ASYNCHRONOUS RECEPTION
Start
bit
bit 0
RX (pin)
bit 1
bit 7/8 Stop
bit
Start
bit
bit 0
Rcv Shift Reg
Rcv Buffer Reg
Stop
bit
Start
bit
bit 7/8
Stop
bit
Word 2
RCREG
Word 1
RCREG
Read Rcv
Buffer Reg
RCREG
bit 7/8
RCIF
(Interrupt Flag)
OERR bit
CREN
Note:
This timing diagram shows three words appearing on the RX input. The RCREG (receive buffer) is read after the third word causing
the OERR (overrun) bit to be set.
TABLE 17-6:
Name
REGISTERS ASSOCIATED WITH ASYNCHRONOUS RECEPTION
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
Values
on page
INT0IE
RBIE
TMR0IF
INT0IF
RBIF
49
INTCON
GIE/GIEH PEIE/GIEL TMR0IE
PIR1
PSPIF(1)
ADIF
RCIF
TXIF
SSPIF
CCP1IF
TMR2IF
TMR1IF
52
PIE1
PSPIE(1)
ADIE
RCIE
TXIE
SSPIE
CCP1IE
TMR2IE
TMR1IE
52
IPR1
PSPIP(1)
ADIP
RCIP
TXIP
SSPIP
CCP1IP
TMR2IP
TMR1IP
52
SPEN
RX9
SREN
CREN
ADDEN
FERR
OERR
RX9D
51
RCSTA
RCREG
TXSTA
EUSART Receive Register
51
CSRC
TX9
TXEN
SYNC
SENDB
BRGH
TRMT
TX9D
51
RCIDL
—
SCKP
BRG16
—
WUE
ABDEN
51
BAUDCON
ABDOVF
SPBRGH
EUSART Baud Rate Generator Register, High Byte
51
SPBRG
EUSART Baud Rate Generator Register, Low Byte
51
Legend: — = unimplemented locations read as ‘0’. Shaded cells are not used for asynchronous reception.
Note 1: These bits are unimplemented on 28-pin devices and read as ‘0’.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 203
PIC18F2X1X/4X1X
17.2.4
AUTO-WAKE-UP ON SYNC BREAK
CHARACTER
During Sleep mode, all clocks to the EUSART are
suspended. Because of this, the Baud Rate Generator
is inactive and a proper byte reception cannot be performed. The auto-wake-up feature allows the controller
to wake-up due to activity on the RX/DT line while the
EUSART is operating in Asynchronous mode.
The auto-wake-up feature is enabled by setting the
WUE bit (BAUDCON<1>). Once set, the typical receive
sequence on RX/DT is disabled and the EUSART
remains in an Idle state, monitoring for a wake-up event
independent of the CPU mode. A wake-up event consists of a high-to-low transition on the RX/DT line. (This
coincides with the start of a Sync Break or a Wake-up
Signal character for the LIN protocol.)
Following a wake-up event, the module generates an
RCIF interrupt. The interrupt is generated synchronously to the Q clocks in normal operating modes
(Figure 17-8) and asynchronously, if the device is in
Sleep mode (Figure 17-9). The interrupt condition is
cleared by reading the RCREG register.
The WUE bit is automatically cleared once a low-to-high
transition is observed on the RX line following the wakeup event. At this point, the EUSART module is in Idle
mode and returns to normal operation. This signals to
the user that the Sync Break event is over.
17.2.4.1
Special Considerations Using
Auto-Wake-up
Since auto-wake-up functions by sensing rising edge
transitions on RX/DT, information with any state
changes before the Stop bit may signal a false end-of-
FIGURE 17-8:
character and cause data or framing errors. To work
properly, therefore, the initial character in the transmission must be all ‘0’s. This can be 00h (8 bytes) for
standard RS-232 devices or 000h (12 bits) for LIN bus.
Oscillator start-up time must also be considered,
especially in applications using oscillators with longer
start-up intervals (i.e., XT or HS mode). The Sync
Break (or Wake-up Signal) character must be of
sufficient length and be followed by a sufficient interval
to allow enough time for the selected oscillator to start
and provide proper initialization of the EUSART.
17.2.4.2
Special Considerations Using
the WUE Bit
The timing of WUE and RCIF events may cause some
confusion when it comes to determining the validity of
received data. As noted, setting the WUE bit places the
EUSART in an Idle mode. The wake-up event causes
a receive interrupt by setting the RCIF bit. The WUE bit
is cleared after this when a rising edge is seen on
RX/DT. The interrupt condition is then cleared by
reading the RCREG register. Ordinarily, the data in
RCREG will be dummy data and should be
discarded.
The fact that the WUE bit has been cleared (or is still
set) and the RCIF flag is set should not be used as an
indicator of the integrity of the data in RCREG. Users
should consider implementing a parallel method in
firmware to verify received data integrity.
To assure that no actual data is lost, check the RCIDL
bit to verify that a receive operation is not in process. If
a receive operation is not occurring, the WUE bit may
then be set just prior to entering the Sleep mode.
AUTO-WAKE-UP BIT (WUE) TIMINGS DURING NORMAL OPERATION
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
OSC1
Bit set by user
Auto-Cleared
WUE bit(1)
RX/DT Line
RCIF
Note 1:
Cleared due to user read of RCREG
The EUSART remains in Idle while the WUE bit is set.
FIGURE 17-9:
AUTO-WAKE-UP BIT (WUE) TIMINGS DURING SLEEP
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
Q1
Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
OSC1
Bit set by user
Auto-Cleared
WUE bit(2)
RX/DT Line
Note 1
RCIF
Sleep Ends
Sleep Command Executed
Note 1:
2:
Cleared due to user read of RCREG
If the wake-up event requires long oscillator warm-up time, the auto-clear of the WUE bit can occur before the oscillator is ready. This
sequence should not depend on the presence of Q clocks.
The EUSART remains in Idle while the WUE bit is set.
DS39636A-page 204
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
17.2.5
BREAK CHARACTER SEQUENCE
The EUSART module has the capability of sending the
special Break character sequences that are required by
the LIN bus standard. The Break character transmit
consists of a Start bit, followed by twelve ‘0’ bits and a
Stop bit. The frame Break character is sent whenever
the SENDB and TXEN bits (TXSTA<3> and
TXSTA<5>) are set while the Transmit Shift register is
loaded with data. Note that the value of data written to
TXREG will be ignored and all ‘0’s will be transmitted.
The SENDB bit is automatically reset by hardware after
the corresponding Stop bit is sent. This allows the user
to preload the transmit FIFO with the next transmit byte
following the Break character (typically, the Sync
character in the LIN specification).
Note that the data value written to the TXREG for the
Break character is ignored. The write simply serves the
purpose of initiating the proper sequence.
The TRMT bit indicates when the transmit operation is
active or Idle, just as it does during normal transmission. See Figure 17-10 for the timing of the Break
character sequence.
17.2.5.1
Break and Sync Transmit Sequence
The following sequence will send a message frame
header made up of a Break, followed by an Auto-Baud
Sync byte. This sequence is typical of a LIN bus
master.
FIGURE 17-10:
Write to TXREG
1.
2.
3.
4.
5.
Configure the EUSART for the desired mode.
Set the TXEN and SENDB bits to set up the
Break character.
Load the TXREG with a dummy character to
initiate transmission (the value is ignored).
Write ‘55h’ to TXREG to load the Sync character
into the transmit FIFO buffer.
After the Break has been sent, the SENDB bit is
reset by hardware. The Sync character now
transmits in the preconfigured mode.
When the TXREG becomes empty, as indicated by the
TXIF, the next data byte can be written to TXREG.
17.2.6
RECEIVING A BREAK CHARACTER
The Enhanced USART module can receive a Break
character in two ways.
The first method forces configuration of the baud rate
at a frequency of 9/13 the typical speed. This allows for
the Stop bit transition to be at the correct sampling
location (13 bits for Break versus Start bit and 8 data
bits for typical data).
The second method uses the auto-wake-up feature
described in Section 17.2.4 “Auto-Wake-up on Sync
Break Character”. By enabling this feature, the
EUSART will sample the next two transitions on RX/DT,
cause an RCIF interrupt and receive the next data byte
followed by another interrupt.
Note that following a Break character, the user will
typically want to enable the Auto-Baud Rate Detect
feature. For both methods, the user can set the ABD bit
once the TXIF interrupt is observed.
SEND BREAK CHARACTER SEQUENCE
Dummy Write
BRG Output
(Shift Clock)
TX (pin)
Start Bit
Bit 0
Bit 1
Bit 11
Stop Bit
Break
TXIF bit
(Transmit Buffer
Reg. Empty Flag)
TRMT bit
(Transmit Shift
Reg. Empty Flag)
SENDB sampled here
Auto-Cleared
SENDB
(Transmit Shift
Reg. Empty Flag)
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 205
PIC18F2X1X/4X1X
17.3
EUSART Synchronous
Master Mode
Once the TXREG register transfers the data to the TSR
register (occurs in one TCY), the TXREG is empty and
the TXIF flag bit (PIR1<4>) is set. The interrupt can be
enabled or disabled by setting or clearing the interrupt
enable bit, TXIE (PIE1<4>). TXIF is set regardless of
the state of enable bit TXIE; it cannot be cleared in
software. It will reset only when new data is loaded into
the TXREG register.
The Synchronous Master mode is entered by setting
the CSRC bit (TXSTA<7>). In this mode, the data is
transmitted in a half-duplex manner (i.e., transmission
and reception do not occur at the same time). When
transmitting data, the reception is inhibited and vice
versa. Synchronous mode is entered by setting bit
SYNC (TXSTA<4>). In addition, enable bit SPEN
(RCSTA<7>) is set in order to configure the TX and RX
pins to CK (clock) and DT (data) lines, respectively.
While flag bit TXIF indicates the status of the TXREG
register, another bit, TRMT (TXSTA<1>), shows the
status of the TSR register. TRMT is a read-only bit which
is set when the TSR is empty. No interrupt logic is tied to
this bit so the user has to poll this bit in order to determine if the TSR register is empty. The TSR is not
mapped in data memory so it is not available to the user.
The Master mode indicates that the processor transmits the master clock on the CK line. Clock polarity is
selected with the SCKP bit (BAUDCON<4>); setting
SCKP sets the Idle state on CK as high, while clearing
the bit sets the Idle state as low. This option is provided
to support Microwire devices with this module.
17.3.1
To set up a Synchronous Master Transmission:
1.
EUSART SYNCHRONOUS MASTER
TRANSMISSION
2.
The EUSART transmitter block diagram is shown in
Figure 17-3. The heart of the transmitter is the Transmit
(Serial) Shift Register (TSR). The Shift register obtains
its data from the Read/Write Transmit Buffer register,
TXREG. The TXREG register is loaded with data in
software. The TSR register is not loaded until the last
bit has been transmitted from the previous load. As
soon as the last bit is transmitted, the TSR is loaded
with new data from the TXREG (if available).
FIGURE 17-11:
3.
4.
5.
6.
7.
8.
Initialize the SPBRGH:SPBRG registers for the
appropriate baud rate. Set or clear the BRG16
bit, as required, to achieve the desired baud rate.
Enable the synchronous master serial port by
setting bits SYNC, SPEN and CSRC.
If interrupts are desired, set enable bit TXIE.
If 9-bit transmission is desired, set bit TX9.
Enable the transmission by setting bit TXEN.
If 9-bit transmission is selected, the ninth bit
should be loaded in bit TX9D.
Start transmission by loading data to the TXREG
register.
If using interrupts, ensure that the GIE and PEIE
bits in the INTCON register (INTCON<7:6>) are
set.
SYNCHRONOUS TRANSMISSION
Q1 Q2 Q3Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1Q2 Q3 Q4 Q1 Q2 Q3 Q4
RC7/RX/DT
pin
bit 0
bit 1
bit 2
Q3 Q4 Q1 Q2 Q3 Q4 Q1Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
bit 7
bit 0
bit 1
bit 7
Word 2
Word 1
RC6/TX/CK pin
(SCKP = 0)
RC6/TX/CK pin
(SCKP = 1)
Write to
TXREG Reg
Write Word 1
Write Word 2
TXIF bit
(Interrupt Flag)
TRMT bit
TXEN bit
Note:
‘1’
‘1’
Sync Master mode, SPBRG = 0, continuous transmission of two 8-bit words.
DS39636A-page 206
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
FIGURE 17-12:
SYNCHRONOUS TRANSMISSION (THROUGH TXEN)
RC7/RX/DT pin
bit 0
bit 1
bit 2
bit 6
bit 7
RC6/TX/CK pin
Write to
TXREG reg
TXIF bit
TRMT bit
TXEN bit
TABLE 17-7:
Name
REGISTERS ASSOCIATED WITH SYNCHRONOUS MASTER TRANSMISSION
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
Values
on page
INT0IE
RBIE
TMR0IF
INT0IF
RBIF
49
INTCON
GIE/GIEH PEIE/GIEL TMR0IE
PIR1
PSPIF(1)
ADIF
RCIF
TXIF
SSPIF
CCP1IF
TMR2IF
TMR1IF
52
PIE1
PSPIE(1)
ADIE
RCIE
TXIE
SSPIE
CCP1IE
TMR2IE
TMR1IE
52
IPR1
PSPIP(1)
ADIP
RCIP
TXIP
SSPIP
CCP1IP
TMR2IP
TMR1IP
52
SPEN
RX9
SREN
CREN
ADDEN
FERR
OERR
RX9D
51
RCSTA
TXREG
EUSART Transmit Register
51
CSRC
TX9
TXEN
SYNC
SENDB
BRGH
TRMT
TX9D
51
BAUDCON
ABDOVF
RCIDL
—
SCKP
BRG16
—
WUE
ABDEN
51
SPBRGH
EUSART Baud Rate Generator Register, High Byte
51
SPBRG
EUSART Baud Rate Generator Register, Low Byte
51
TXSTA
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used for synchronous master transmission.
Note 1: These bits are unimplemented on 28-pin devices and read as ‘0’.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 207
PIC18F2X1X/4X1X
17.3.2
EUSART SYNCHRONOUS
MASTER RECEPTION
Once Synchronous mode is selected, reception is
enabled by setting either the Single Receive Enable bit,
SREN (RCSTA<5>), or the Continuous Receive
Enable bit, CREN (RCSTA<4>). Data is sampled on the
RX pin on the falling edge of the clock.
If enable bit SREN is set, only a single word is received.
If enable bit CREN is set, the reception is continuous
until CREN is cleared. If both bits are set, then CREN
takes precedence.
To set up a Synchronous Master Reception:
1.
2.
Initialize the SPBRGH:SPBRG registers for the
appropriate baud rate. Set or clear the BRG16
bit, as required, to achieve the desired baud rate.
Enable the synchronous master serial port by
setting bits SYNC, SPEN and CSRC.
FIGURE 17-13:
3.
4.
5.
6.
Ensure bits CREN and SREN are clear.
If interrupts are desired, set enable bit RCIE.
If 9-bit reception is desired, set bit RX9.
If a single reception is required, set bit SREN.
For continuous reception, set bit CREN.
7. Interrupt flag bit RCIF will be set when reception
is complete and an interrupt will be generated if
the enable bit RCIE was set.
8. Read the RCSTA register to get the 9th bit (if
enabled) and determine if any error occurred
during reception.
9. Read the 8-bit received data by reading the
RCREG register.
10. If any error occurred, clear the error by clearing
bit CREN.
11. If using interrupts, ensure that the GIE and PEIE
bits in the INTCON register (INTCON<7:6>) are
set.
SYNCHRONOUS RECEPTION (MASTER MODE, SREN)
Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
RC7/RX/DT
pin
bit 0
bit 1
bit 2
bit 3
bit 4
bit 5
bit 6
bit 7
RC7/TX/CK pin
(SCKP = 0)
RC7/TX/CK pin
(SCKP = 1)
Write to
bit SREN
SREN bit
CREN bit ‘0’
‘0’
RCIF bit
(Interrupt)
Read
RXREG
Note:
Timing diagram demonstrates Sync Master mode with bit SREN = 1 and bit BRGH = 0.
TABLE 17-8:
Name
REGISTERS ASSOCIATED WITH SYNCHRONOUS MASTER RECEPTION
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
Values on
page
49
INTCON
GIE/GIEH
PEIE/GIEL
TMR0IE
INT0IE
RBIE
TMR0IF
INT0IF
RBIF
PIR1
PSPIF(1)
ADIF
RCIF
TXIF
SSPIF
CCP1IF
TMR2IF
TMR1IF
52
PIE1
PSPIE(1)
ADIE
RCIE
TXIE
SSPIE
CCP1IE
TMR2IE
TMR1IE
52
IPR1
PSPIP(1)
ADIP
RCIP
TXIP
SSPIP
CCP1IP
TMR2IP
TMR1IP
52
SPEN
RX9
SREN
CREN
ADDEN
FERR
OERR
RX9D
RCSTA
RCREG
TXSTA
BAUDCON
EUSART Receive Register
51
51
CSRC
TX9
TXEN
SYNC
SENDB
BRGH
TRMT
TX9D
51
ABDOVF
RCIDL
—
SCKP
BRG16
—
WUE
ABDEN
51
SPBRGH
EUSART Baud Rate Generator Register, High Byte
51
SPBRG
EUSART Baud Rate Generator Register, Low Byte
51
Legend:
Note 1:
— = unimplemented, read as ‘0’. Shaded cells are not used for synchronous master reception.
These bits are unimplemented on 28-pin devices and read as ‘0’.
DS39636A-page 208
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
17.4
EUSART Synchronous
Slave Mode
To set up a Synchronous Slave Transmission:
1.
Synchronous Slave mode is entered by clearing bit,
CSRC (TXSTA<7>). This mode differs from the
Synchronous Master mode in that the shift clock is supplied externally at the CK pin (instead of being supplied
internally in Master mode). This allows the device to
transfer or receive data while in any low-power mode.
17.4.1
EUSART SYNCHRONOUS
SLAVE TRANSMIT
2.
3.
4.
5.
6.
The operation of the Synchronous Master and Slave
modes are identical, except in the case of the Sleep
mode.
7.
8.
If two words are written to the TXREG and then the
SLEEP instruction is executed, the following will occur:
a)
b)
c)
d)
e)
Enable the synchronous slave serial port by
setting bits SYNC and SPEN and clearing bit
CSRC.
Clear bits CREN and SREN.
If interrupts are desired, set enable bit TXIE.
If 9-bit transmission is desired, set bit TX9.
Enable the transmission by setting enable bit
TXEN.
If 9-bit transmission is selected, the ninth bit
should be loaded in bit TX9D.
Start transmission by loading data to the
TXREGx register.
If using interrupts, ensure that the GIE and PEIE
bits in the INTCON register (INTCON<7:6>) are
set.
The first word will immediately transfer to the
TSR register and transmit.
The second word will remain in the TXREG
register.
Flag bit TXIF will not be set.
When the first word has been shifted out of TSR,
the TXREG register will transfer the second
word to the TSR and flag bit TXIF will now be
set.
If enable bit TXIE is set, the interrupt will wake the
chip from Sleep. If the global interrupt is enabled,
the program will branch to the interrupt vector.
TABLE 17-9:
Name
REGISTERS ASSOCIATED WITH SYNCHRONOUS SLAVE TRANSMISSION
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
Values
on page
INT0IE
RBIE
TMR0IF
INT0IF
RBIF
49
INTCON
GIE/GIEH PEIE/GIEL TMR0IE
PIR1
PSPIF(1)
ADIF
RCIF
TXIF
SSPIF
CCP1IF
TMR2IF
TMR1IF
52
PIE1
PSPIE(1)
ADIE
RCIE
TXIE
SSPIE
CCP1IE
TMR2IE
TMR1IE
52
IPR1
PSPIP(1)
ADIP
RCIP
TXIP
SSPIP
CCP1IP
TMR2IP
TMR1IP
52
SPEN
RX9
SREN
CREN
ADDEN
FERR
OERR
RX9D
51
RCSTA
TXREG
TXSTA
EUSART Transmit Register
51
CSRC
TX9
TXEN
SYNC
SENDB
BRGH
TRMT
TX9D
51
RCIDL
—
SCKP
BRG16
—
WUE
ABDEN
51
BAUDCON
ABDOVF
SPBRGH
EUSART Baud Rate Generator Register, High Byte
51
SPBRG
EUSART Baud Rate Generator Register, Low Byte
51
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used for synchronous slave transmission.
Note 1: These bits are unimplemented on 28-pin devices and read as ‘0’.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 209
PIC18F2X1X/4X1X
17.4.2
EUSART SYNCHRONOUS SLAVE
RECEPTION
To set up a Synchronous Slave Reception:
1.
The operation of the Synchronous Master and Slave
modes is identical, except in the case of Sleep, or any
Idle mode and bit SREN, which is a “don’t care” in
Slave mode.
If receive is enabled by setting the CREN bit prior to
entering Sleep or any Idle mode, then a word may be
received while in this low-power mode. Once the word
is received, the RSR register will transfer the data to the
RCREG register; if the RCIE enable bit is set, the interrupt generated will wake the chip from the low-power
mode. If the global interrupt is enabled, the program will
branch to the interrupt vector.
2.
3.
4.
5.
6.
7.
8.
9.
Enable the synchronous master serial port by
setting bits SYNC and SPEN and clearing bit
CSRC.
If interrupts are desired, set enable bit RCIE.
If 9-bit reception is desired, set bit RX9.
To enable reception, set enable bit CREN.
Flag bit RCIF will be set when reception is
complete. An interrupt will be generated if
enable bit RCIE was set.
Read the RCSTA register to get the 9th bit (if
enabled) and determine if any error occurred
during reception.
Read the 8-bit received data by reading the
RCREG register.
If any error occurred, clear the error by clearing
bit CREN.
If using interrupts, ensure that the GIE and PEIE
bits in the INTCON register (INTCON<7:6>) are
set.
TABLE 17-10: REGISTERS ASSOCIATED WITH SYNCHRONOUS SLAVE RECEPTION
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
Values
on page
INTCON
GIE/GIEH PEIE/GIEL TMR0IE
INT0IE
RBIE
TMR0IF
INT0IF
RBIF
49
PIR1
PSPIF(1)
ADIF
RCIF
TXIF
SSPIF
CCP1IF
TMR2IF
TMR1IF
52
PIE1
PSPIE(1)
ADIE
RCIE
TXIE
SSPIE
CCP1IE
TMR2IE
TMR1IE
52
IPR1
PSPIP(1)
ADIP
RCIP
TXIP
SSPIP
CCP1IP
TMR2IP
TMR1IP
52
SPEN
RX9
SREN
CREN
ADDEN
FERR
OERR
RX9D
51
RCSTA
RCREG
TXSTA
BAUDCON
EUSART Receive Register
51
CSRC
TX9
TXEN
SYNC
SENDB
BRGH
TRMT
TX9D
51
ABDOVF
RCIDL
—
SCKP
BRG16
—
WUE
ABDEN
51
SPBRGH
EUSART Baud Rate Generator Register, High Byte
51
SPBRG
EUSART Baud Rate Generator Register, Low Byte
51
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used for synchronous slave reception.
Note 1: These bits are unimplemented on 28-pin devices and read as ‘0’.
DS39636A-page 210
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
18.0
10-BIT ANALOG-TO-DIGITAL
CONVERTER (A/D) MODULE
The ADCON0 register, shown in Register 18-1,
controls the operation of the A/D module. The
ADCON1 register, shown in Register 18-2, configures
the functions of the port pins. The ADCON2 register,
shown in Register 18-3, configures the A/D clock
source, programmed acquisition time and justification.
The Analog-to-Digital (A/D) converter module has
10 inputs for the 28-pin devices and 13 for the 40/44-pin
devices. This module allows conversion of an analog
input signal to a corresponding 10-bit digital number.
The module has five registers:
•
•
•
•
•
A/D Result High Register (ADRESH)
A/D Result Low Register (ADRESL)
A/D Control Register 0 (ADCON0)
A/D Control Register 1 (ADCON1)
A/D Control Register 2 (ADCON2)
REGISTER 18-1:
ADCON0: A/D CONTROL REGISTER 0
U-0
U-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
—
—
CHS3
CHS2
CHS1
CHS0
GO/DONE
ADON
bit 7
bit 0
bit 7-6
Unimplemented: Read as ‘0’
bit 5-2
CHS3:CHS0: Analog Channel Select bits
0000 = Channel 0 (AN0)
0001 = Channel 1 (AN1)
0010 = Channel 2 (AN2)
0011 = Channel 3 (AN3)
0100 = Channel 4 (AN4)
0101 = Channel 5 (AN5)(1,2)
0110 = Channel 6 (AN6)(1,2)
0111 = Channel 7 (AN7)(1,2)
1000 = Channel 8 (AN8)
1001 = Channel 9 (AN9)
1010 = Channel 10 (AN10)
1011 = Channel 11 (AN11)
1100 = Channel 12 (AN12
1101 = Unimplemented(2)
1110 = Unimplemented(2)
1111 = Unimplemented(2)
Note 1: These channels are not implemented on 28-pin devices.
2: Performing a conversion on unimplemented channels will return a floating input
measurement.
bit 1
GO/DONE: A/D Conversion Status bit
When ADON = 1:
1 = A/D conversion in progress
0 = A/D Idle
bit 0
ADON: A/D On bit
1 = A/D converter module is enabled
0 = A/D converter module is disabled
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
 2004 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS39636A-page 211
PIC18F2X1X/4X1X
REGISTER 18-2:
ADCON1: A/D CONTROL REGISTER 1
U-0
U-0
R/W-0
R/W-0
R/W-0(1)
R/W(1)
R/W(1)
R/W(1)
—
—
VCFG1
VCFG0
PCFG3
PCFG2
PCFG1
PCFG0
bit 7
bit 0
PCFG3:
PCFG0
AN7(2)
AN6(2)
AN5(2)
AN4
AN3
AN2
AN1
AN0
PCFG3:PCFG0: A/D Port Configuration Control bits:
AN8
bit 3-0
AN9
VCFG0: Voltage Reference Configuration bit (VREF+ source)
1 = VREF+ (AN3)
0 = VDD
AN10
bit 4
AN11
Unimplemented: Read as ‘0’
VCFG1: Voltage Reference Configuration bit (VREF- source)
1 = VREF- (AN2)
0 = VSS
AN12
bit 7-6
bit 5
0000(1)
0001
0010
0011
0100
0101
0110
A
A
A
D
D
D
D
D
A
A
A
A
D
D
D
D
A
A
A
A
A
D
D
D
A
A
A
A
A
A
D
D
A
A
A
A
A
A
A
D
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
A
D
D
D
D
D
D
D
A
A
D
D
D
D
D
D
A
A
A
D
D
D
D
D
A
A
A
A
D
D
D
D
A
A
A
A
A
D
D
D
A
A
A
A
A
A
D
D
A
A
A
A
A
A
A
D
0111(1)
1000
1001
1010
1011
1100
1101
1110
1111
A = Analog input
Note 1:
2:
D = Digital I/O
The POR value of the PCFG bits depends on the value of the PBADEN
configuration bit. When PBADEN = 1, PCFG<3:0> = 0000; when PBADEN = 0,
PCFG<3:0> = 0111.
AN5 through AN7 are available only on 40/44-pin devices.
Legend:
DS39636A-page 212
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
Preliminary
x = Bit is unknown
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
REGISTER 18-3:
ADCON2: A/D CONTROL REGISTER 2
R/W-0
U-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
ADFM
—
ACQT2
ACQT1
ACQT0
ADCS2
ADCS1
ADCS0
bit 7
bit 0
bit 7
ADFM: A/D Result Format Select bit
1 = Right justified
0 = Left justified
bit 6
Unimplemented: Read as ‘0’
bit 5-3
ACQT2:ACQT0: A/D Acquisition Time Select bits
111 = 20 TAD
110 = 16 TAD
101 = 12 TAD
100 = 8 TAD
011 = 6 TAD
010 = 4 TAD
001 = 2 TAD
000 = 0 TAD(1)
bit 2-0
ADCS2:ADCS0: A/D Conversion Clock Select bits
111 = FRC (clock derived from A/D RC oscillator)(1)
110 = FOSC/64
101 = FOSC/16
100 = FOSC/4
011 = FRC (clock derived from A/D RC oscillator)(1)
010 = FOSC/32
001 = FOSC/8
000 = FOSC/2
Note 1: If the A/D FRC clock source is selected, a delay of one TCY (instruction cycle) is
added before the A/D clock starts. This allows the SLEEP instruction to be executed
before starting a conversion.
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
 2004 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS39636A-page 213
PIC18F2X1X/4X1X
The analog reference voltage is software selectable
to either the device’s positive and negative supply
voltage (VDD and VSS), or the voltage level on the
RA3/AN3/VREF+ and RA2/AN2/VREF-/CVREF pins.
A device Reset forces all registers to their Reset state.
This forces the A/D module to be turned off and any
conversion in progress is aborted.
Each port pin associated with the A/D converter can
be configured as an analog input, or as a digital I/O.
The ADRESH and ADRESL registers contain the
result of the A/D conversion. When the A/D
conversion is complete, the result is loaded into the
ADRESH:ADRESL register pair, the GO/DONE bit
(ADCON0 register) is cleared and A/D Interrupt Flag
bit ADIF is set. The block diagram of the A/D module
is shown in Figure 18-1.
The A/D converter has a unique feature of being able
to operate while the device is in Sleep mode. To operate in Sleep, the A/D conversion clock must be derived
from the A/D’s internal RC oscillator.
The output of the sample and hold is the input into the
converter, which generates the result via successive
approximation.
FIGURE 18-1:
A/D BLOCK DIAGRAM
CHS3:CHS0
1100
1011
1010
1001
1000
Reference
Voltage
VREF+
X0
X1
1X
VREF-
0X
AN8
AN6(1)
0101
AN5(1)
0010
0001
0000
VDD
AN9
0110
0011
VCFG1:VCFG0
AN10
AN7(1)
0100
(Input Voltage)
AN11
0111
VAIN
10-bit
Converter
A/D
AN12
AN4
AN3
AN2
AN1
AN0
VSS
Note 1:
2:
Channels AN5 through AN7 are not available on 28-pin devices.
I/O pins have diode protection to VDD and VSS.
DS39636A-page 214
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
Wait for A/D conversion to complete, by either:
• Polling for the GO/DONE bit to be cleared
OR
• Waiting for the A/D interrupt
Read A/D Result registers (ADRESH:ADRESL);
clear bit ADIF, if required.
For next conversion, go to step 1 or step 2, as
required. The A/D conversion time per bit is
defined as TAD. A minimum wait of 2 TAD is
required before the next acquisition starts.
6.
7.
FIGURE 18-2:
To perform an A/D conversion, do the following steps:
FIGURE 18-3:
003h
002h
001h
1023 LSB
1023.5 LSB
1022 LSB
1022.5 LSB
3 LSB
Analog Input Voltage
ANALOG INPUT MODEL
VDD
Sampling
Switch
VT = 0.6V
Rs
VAIN
2 LSB
000h
2.5 LSB
3.
4.
3FEh
0.5 LSB
2.
A/D TRANSFER FUNCTION
3FFh
Configure the A/D module:
• Configure analog pins, voltage reference and
digital I/O (ADCON1)
• Select A/D input channel (ADCON0)
• Select A/D acquisition time (ADCON2)
• Select A/D conversion clock (ADCON2)
• Turn on A/D module (ADCON0)
Configure A/D interrupt (if desired):
• Clear ADIF bit
• Set ADIE bit
• Set GIE bit
Wait the required acquisition time (if required).
Start conversion:
• Set GO/DONE bit (ADCON0 register)
Digital Code Output
1.
1 LSB
After the A/D module has been configured as desired,
the selected channel must be acquired before the conversion is started. The analog input channels must
have their corresponding TRIS bits selected as an
input. To determine acquisition time, see Section 18.1
“A/D Acquisition Requirements”. After this acquisition time has elapsed, the A/D conversion can be
started. An acquisition time can be programmed to
occur between setting the GO/DONE bit and the actual
start of the conversion.
5.
1.5 LSB
The value in the ADRESH:ADRESL registers is not
modified for a Power-on Reset. The ADRESH:ADRESL
registers will contain unknown data after a Power-on
Reset.
ANx
RIC ≤ 1k
CPIN
5 pF
VT = 0.6V
SS
RSS
ILEAKAGE
± 100 nA
CHOLD = 25 pF
VSS
Legend: CPIN
= input capacitance
VT
= threshold voltage
ILEAKAGE = leakage current at the pin due to
various junctions
= interconnect resistance
RIC
= sampling switch
SS
= sample/hold capacitance (from DAC)
CHOLD
RSS
= sampling switch resistance
 2004 Microchip Technology Inc.
Preliminary
VDD
6V
5V
4V
3V
2V
1
2
3
4
Sampling Switch (kΩ)
DS39636A-page 215
PIC18F2X1X/4X1X
18.1
A/D Acquisition Requirements
For the A/D converter to meet its specified accuracy,
the charge holding capacitor (CHOLD) must be allowed
to fully charge to the input channel voltage level. The
analog input model is shown in Figure 18-3. The
source impedance (RS) and the internal sampling
switch (RSS) impedance directly affect the time
required to charge the capacitor CHOLD. The sampling
switch (RSS) impedance varies over the device voltage
(VDD). The source impedance affects the offset voltage
at the analog input (due to pin leakage current). The
maximum recommended impedance for analog
sources is 2.5 kΩ. After the analog input channel is
selected (changed), the channel must be sampled for
at least the minimum acquisition time before starting a
conversion.
Note:
CHOLD
Rs
Conversion Error
VDD
Temperature
=
=
≤
=
=
25 pF
2.5 kΩ
1/2 LSb
5V → Rss = 2 kΩ
85°C (system max.)
ACQUISITION TIME
=
Amplifier Settling Time + Holding Capacitor Charging Time + Temperature Coefficient
=
TAMP + TC + TCOFF
EQUATION 18-2:
VHOLD
or
TC
Example 18-3 shows the calculation of the minimum
required acquisition time TACQ. This calculation is
based on the following application system
assumptions:
When the conversion is started, the
holding capacitor is disconnected from the
input pin.
EQUATION 18-1:
TACQ
To calculate the minimum acquisition time,
Equation 18-1 may be used. This equation assumes
that 1/2 LSb error is used (1024 steps for the A/D). The
1/2 LSb error is the maximum error allowed for the A/D
to meet its specified resolution.
A/D MINIMUM CHARGING TIME
=
(VREF – (VREF/2048)) • (1 – e(-TC/CHOLD(RIC + RSS + RS)))
=
-(CHOLD)(RIC + RSS + RS) ln(1/2048)
EQUATION 18-3:
CALCULATING THE MINIMUM REQUIRED ACQUISITION TIME
TACQ
=
TAMP + TC + TCOFF
TAMP
=
0.2 µs
TCOFF
=
(Temp – 25°C)(0.02 µs/°C)
(85°C – 25°C)(0.02 µs/°C)
1.2 µs
Temperature coefficient is only required for temperatures > 25°C. Below 25°C, TCOFF = 0 ms.
TC
=
-(CHOLD)(RIC + RSS + RS) ln(1/2047)
-(25 pF) (1 kΩ + 2 kΩ + 2.5 kΩ) ln(0.0004883)
1.05 µs
TACQ
=
0.2 µs + 1 µs + 1.2 µs
2.4 µs
DS39636A-page 216
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
18.2
Selecting and Configuring
Acquisition Time
18.3
Selecting the A/D Conversion
Clock
The ADCON2 register allows the user to select an
acquisition time that occurs each time the GO/DONE
bit is set. It also gives users the option to use an
automatically determined acquisition time.
The A/D conversion time per bit is defined as TAD. The
A/D conversion requires 11 TAD per 10-bit conversion.
The source of the A/D conversion clock is software
selectable. There are seven possible options for TAD:
Acquisition time may be set with the ACQT2:ACQT0
bits (ADCON2<5:3>), which provides a range of 2 to
20 TAD. When the GO/DONE bit is set, the A/D module
continues to sample the input for the selected acquisition time, then automatically begins a conversion.
Since the acquisition time is programmed, there may
be no need to wait for an acquisition time between
selecting a channel and setting the GO/DONE bit.
•
•
•
•
•
•
•
Manual
acquisition
is
selected
when
ACQT2:ACQT0 = 000. When the GO/DONE bit is set,
sampling is stopped and a conversion begins. The user
is responsible for ensuring the required acquisition time
has passed between selecting the desired input channel
and setting the GO/DONE bit. This option is also the
default Reset state of the ACQT2:ACQT0 bits and is
compatible with devices that do not offer programmable
acquisition times.
For correct A/D conversions, the A/D conversion clock
(TAD) must be as short as possible, but greater than the
minimum TAD (see parameter 130 for more
information).
2 TOSC
4 TOSC
8 TOSC
16 TOSC
32 TOSC
64 TOSC
Internal RC Oscillator
Table 18-1 shows the resultant TAD times derived from
the device operating frequencies and the A/D clock
source selected.
In either case, when the conversion is completed, the
GO/DONE bit is cleared, the ADIF flag is set and the
A/D begins sampling the currently selected channel
again. If an acquisition time is programmed, there is
nothing to indicate if the acquisition time has ended or
if the conversion has begun.
TABLE 18-1:
TAD vs. DEVICE OPERATING FREQUENCIES
AD Clock Source (TAD)
4:
PIC18LFXXXX(4)
Operation
ADCS2:ADCS0
PIC18FXXXX
2 TOSC
000
2.86 MHz
1.43 kHz
4 TOSC
100
5.71 MHz
2.86 MHz
8 TOSC
001
11.43 MHz
5.72 MHz
16 TOSC
101
22.86 MHz
11.43 MHz
32 TOSC
010
40.0 MHz
22.86 MHz
64 TOSC
110
40.0 MHz
22.86 MHz
RC(3)
Note 1:
2:
3:
Maximum Device Frequency
1.00
x11
MHz(1)
1.00 MHz(2)
The RC source has a typical TAD time of 0.9 µs.
The RC source has a typical TAD time of 1.2 µs.
For device frequencies above 1 MHz, the device must be in Sleep for the entire conversion or the A/D
accuracy may be out of specification.
Low-power (PIC18LFXXXX) devices only.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 217
PIC18F2X1X/4X1X
18.4
Operation in Power Managed
Modes
18.5
The selection of the automatic acquisition time and
A/D conversion clock is determined in part by the
clock source and frequency while in a power
managed mode.
If the A/D is expected to operate while the device is in
a power managed mode, the ACQT2:ACQT0 and
ADCS2:ADCS0 bits in ADCON2 should be updated in
accordance with the clock source to be used in that
mode. After entering the mode, an A/D acquisition or
conversion may be started. Once started, the device
should continue to be clocked by the same clock
source until the conversion has been completed.
If desired, the device may be placed into the
corresponding Idle mode during the conversion. If the
device clock frequency is less than 1 MHz, the A/D RC
clock source should be selected.
The ADCON1, TRISA, TRISB and TRISE registers all
configure the A/D port pins. The port pins needed as
analog inputs must have their corresponding TRIS bits
set (input). If the TRIS bit is cleared (output), the digital
output level (VOH or VOL) will be converted.
The A/D operation is independent of the state of the
CHS3:CHS0 bits and the TRIS bits.
Note 1: When reading the Port register, all pins
configured as analog input channels will
read as cleared (a low level). Pins configured as digital inputs will convert as
analog inputs. Analog levels on a digitally
configured input will be accurately
converted.
Operation in the Sleep mode requires the A/D FRC
clock to be selected. If bits ACQT2:ACQT0 are set to
‘000’ and a conversion is started, the conversion will be
delayed one instruction cycle to allow execution of the
SLEEP instruction and entry to Sleep mode. The IDLEN
bit (OSCCON<7>) must have already been cleared
prior to starting the conversion.
DS39636A-page 218
Configuring Analog Port Pins
Preliminary
2: Analog levels on any pin defined as a
digital input may cause the digital input
buffer to consume current out of the
device’s specification limits.
3: The PBADEN bit in Configuration
Register 3H configures PORTB pins to
reset as analog or digital pins by controlling how the PCFG0 bits in ADCON1 are
reset.
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
18.6
A/D Conversions
After the A/D conversion is completed or aborted, a
2 TAD wait is required before the next acquisition can be
started. After this wait, acquisition on the selected
channel is automatically started.
Figure 18-4 shows the operation of the A/D converter
after the GO bit has been set and the ACQT2:ACQT0
bits are cleared. A conversion is started after the following instruction to allow entry into Sleep mode before the
conversion begins.
Note:
Figure 18-5 shows the operation of the A/D converter
after the GO bit has been set and the ACQT2:ACQT0
bits are set to ‘010’ and selecting a 4 TAD acquisition
time before the conversion starts.
18.7
Discharge
The discharge phase is used to initialize the value of
the capacitor array. The array is discharged before
every sample. This feature helps to optimize the unitygain amplifier, as the circuit always needs to charge the
capacitor array, rather than charge/discharge based on
previous measure values.
Clearing the GO/DONE bit during a conversion will
abort the current conversion. The A/D Result register
pair will NOT be updated with the partially completed
A/D
conversion
sample.
This
means
the
ADRESH:ADRESL registers will continue to contain
the value of the last completed conversion (or the last
value written to the ADRESH:ADRESL registers).
FIGURE 18-4:
The GO/DONE bit should NOT be set in
the same instruction that turns on the A/D.
A/D CONVERSION TAD CYCLES (ACQT<2:0> = 000, TACQ = 0)
TCY - TAD TAD1 TAD2 TAD3 TAD4 TAD5 TAD6 TAD7 TAD8 TAD9 TAD10 TAD11 TAD1
b4
b1
b0
b6
b7
b2
b9
b8
b3
b5
Conversion starts
Discharge
Holding capacitor is disconnected from analog input (typically 100 ns)
Set GO bit
On the following cycle:
ADRESH:ADRESL is loaded, GO bit is cleared,
ADIF bit is set, holding capacitor is connected to analog input.
FIGURE 18-5:
A/D CONVERSION TAD CYCLES (ACQT<2:0> = 010, TACQ = 4 TAD)
TAD Cycles
TACQT Cycles
1
2
3
Automatic
Acquisition
Time
4
1
2
3
4
5
6
7
8
9
10
11
b9
b8
b7
b6
b5
b4
b3
b2
b1
b0
Conversion starts
(Holding capacitor is disconnected)
Set GO bit
(Holding capacitor continues
acquiring input)
 2004 Microchip Technology Inc.
TAD1
Discharge
On the following cycle:
ADRESH:ADRESL is loaded, GO bit is cleared,
ADIF bit is set, holding capacitor is connected to analog input.
Preliminary
DS39636A-page 219
PIC18F2X1X/4X1X
18.8
Use of the CCP2 Trigger
An A/D conversion can be started by the special event
trigger of the CCP2 module. This requires that the
CCP2M3:CCP2M0 bits (CCP2CON<3:0>) be programmed as ‘1011’ and that the A/D module is enabled
(ADON bit is set). When the trigger occurs, the GO/
DONE bit will be set, starting the A/D acquisition and
conversion and the Timer1 (or Timer3) counter will be
reset to zero. Timer1 (or Timer3) is reset to automatically repeat the A/D acquisition period with minimal
TABLE 18-2:
Name
software overhead (moving ADRESH:ADRESL to the
desired location). The appropriate analog input
channel must be selected and the minimum acquisition
period is either timed by the user, or an appropriate
TACQ time selected before the special event trigger sets
the GO/DONE bit (starts a conversion).
If the A/D module is not enabled (ADON is cleared), the
special event trigger will be ignored by the A/D module
but will still reset the Timer1 (or Timer3) counter.
REGISTERS ASSOCIATED WITH A/D OPERATION
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
Values
on page
TMR0IE
INT0IE
RBIE
TMR0IF
INT0IF
RBIF
49
INTCON
GIE/GIEH PEIE/GIEL
PIR1
PSPIF(1)
ADIF
RCIF
TXIF
SSPIF
CCP1IF
TMR2IF
TMR1IF
52
PIE1
PSPIE(1)
ADIE
RCIE
TXIE
SSPIE
CCP1IE
TMR2IE
TMR1IE
52
IPR1
PSPIP(1)
ADIP
RCIP
TXIP
SSPIP
CCP1IP
TMR2IP
TMR1IP
52
PIR2
OSCFIF
CMIF
—
—
BCLIF
HLVDIF
TMR3IF
CCP2IF
52
PIE2
OSCFIE
CMIE
—
—
BCLIE
HLVDIE
TMR3IE
CCP2IE
52
IPR2
OSCFIP
CMIP
—
—
BCLIP
HLVDIP
TMR3IP
CCP2IP
52
ADRESH
A/D Result Register, High Byte
51
ADRESL
A/D Result Register, Low Byte
51
ADCON0
—
—
CHS3
CHS2
CHS1
CHS0
GO/DONE
ADON
51
ADCON1
—
—
VCFG1
VCFG0
PCFG3
PCFG2
PCFG1
PCFG0
51
ADCON2
ADFM
—
ACQT2
ACQT1
ACQT0
ADCS2
ADCS1
ADCS0
51
PORTA
RA7(1)
RA6(1)
RA5
RA4
RA3
RA2
RA1
RA0
52
RB1
RB0
52
TRISA
PORTB
TRISA7(2) TRISA6(2) PORTA Data Direction Control Register
RB7
RB6
RB5
RB4
RB3
RB2
52
TRISB
PORTB Data Direction Control Register
52
LATB
PORTB Data Latch Register (Read and Write to Data Latch)
52
PORTE(4)
(4)
TRISE
(4)
LATE
—
—
—
—
RE3(3)
RE2
RE1
RE0
52
IBF
OBF
IBOV
PSPMODE
—
TRISE2
TRISE1
TRISE0
52
—
—
—
—
—
PORTE Data Latch Register
52
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used for A/D conversion.
Note 1: These bits are unimplemented on 28-pin devices; always maintain these bits clear.
2: PORTA<7:6> and their direction bits are individually configured as port pins based on various primary
oscillator modes. When disabled, these bits read as ‘0’.
3: RE3 port bit is available only as an input pin when the MCLRE configuration bit is ‘0’.
4: These registers are not implemented on 28-pin devices.
DS39636A-page 220
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
19.0
COMPARATOR MODULE
The analog comparator module contains two comparators that can be configured in a variety of ways. The
inputs can be selected from the analog inputs multiplexed
with pins RA0 through RA5, as well as the on-chip voltage reference (see Section 20.0 “Comparator Voltage
Reference Module”). The digital outputs (normal or
inverted) are available at the pin level and can also be
read through the control register.
REGISTER 19-1:
The CMCON register (Register 19-1) selects the
comparator input and output configuration. Block
diagrams of the various comparator configurations are
shown in Figure 19-1.
CMCON: COMPARATOR CONTROL REGISTER
R-0
R-0
R/W-0
R/W-0
R/W-0
R/W-1
R/W-1
R/W-1
C2OUT
C1OUT
C2INV
C1INV
CIS
CM2
CM1
CM0
bit 7
bit 0
bit 7
C2OUT: Comparator 2 Output bit
When C2INV = 0:
1 = C2 VIN+ > C2 VIN0 = C2 VIN+ < C2 VINWhen C2INV = 1:
1 = C2 VIN+ < C2 VIN0 = C2 VIN+ > C2 VIN-
bit 6
C1OUT: Comparator 1 Output bit
When C1INV = 0:
1 = C1 VIN+ > C1 VIN0 = C1 VIN+ < C1 VINWhen C1INV = 1:
1 = C1 VIN+ < C1 VIN0 = C1 VIN+ > C1 VIN-
bit 5
C2INV: Comparator 2 Output Inversion bit
1 = C2 output inverted
0 = C2 output not inverted
bit 4
C1INV: Comparator 1 Output Inversion bit
1 = C1 output inverted
0 = C1 output not inverted
bit 3
CIS: Comparator Input Switch bit
When CM2:CM0 = 110:
1 = C1 VIN+ connects to RA3/AN3/VREF+
C2 VIN+ connects to RA2/AN2/VREF-/CVREF
0 = C1 VIN- connects to RA0/AN0
C2 VIN- connects to RA1/AN1
bit 2-0
CM2:CM0: Comparator Mode bits
Figure 19-1 shows the Comparator modes and the CM2:CM0 bit settings.
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
 2004 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS39636A-page 221
PIC18F2X1X/4X1X
19.1
Comparator Configuration
There are eight modes of operation for the comparators, shown in Figure 19-1. Bits CM2:CM0 of the
CMCON register are used to select these modes. The
TRISA register controls the data direction of the comparator pins for each mode. If the Comparator mode is
FIGURE 19-1:
VIN-
RA3/AN3/ A
VREF+
VIN+
A
VIN-
RA2/AN2/ A
VREF-/CVREF
VIN+
C1
Off (Read as ‘0’)
C2
Off (Read as ‘0’)
Two Independent Comparators
CM2:CM0 = 010
A
VIN-
RA3/AN3/ A
VREF+
VIN+
A
VIN-
RA2/AN2/ A
VREF-/CVREF
VIN+
RA0/AN0
Comparator interrupts should be disabled
during a Comparator mode change;
otherwise, a false interrupt may occur.
Comparators Off (POR Default Value)
CM2:CM0 = 111
A
RA1/AN1
Note:
COMPARATOR I/O OPERATING MODES
Comparators Reset
CM2:CM0 = 000
RA0/AN0
changed, the comparator output level may not be valid
for the specified mode change delay shown in
Section 25.0 “Electrical Characteristics”.
C1
RA0/AN0
D
VIN-
RA3/AN3/
VREF+
D
VIN+
RA1/AN1
D
VIN-
D
RA2/AN2/
VREF-/CVREF
VIN+
C1
Off (Read as ‘0’)
C2
Off (Read as ‘0’)
Two Independent Comparators with Outputs
CM2:CM0 = 011
RA0/AN0
RA3/AN3/
VREF+
C1OUT
A
VIN-
A
VIN+
C1
C1OUT
C2
C2OUT
RA4/T0CKI/C1OUT*
RA1/AN1
C2
A
VIN-
RA2/AN2/ A
VREF-/CVREF
VIN+
RA1/AN1
C2OUT
RA5/AN4/SS/HLVDIN/C2OUT*
Two Common Reference Comparators
CM2:CM0 = 100
A
VIN-
RA3/AN3/ A
VREF+
VIN+
A
VIN-
RA2/AN2/ D
VREF-/CVREF
VIN+
RA0/AN0
C1
Two Common Reference Comparators with Outputs
CM2:CM0 = 101
RA0/AN0
RA3/AN3/
VREF+
C1OUT
A
VIN-
A
VIN+
C1
C1OUT
C2
C2OUT
RA4/T0CKI/C1OUT*
RA1/AN1
C2
A
VIN-
RA2/AN2/
D
VREF-/CVREF
VIN+
RA1/AN1
C2OUT
RA5/AN4/SS/HLVDIN/C2OUT*
Four Inputs Multiplexed to Two Comparators
CM2:CM0 = 110
One Independent Comparator with Output
CM2:CM0 = 001
A
VIN-
RA3/AN3/ A
VREF+
VIN+
RA0/AN0
C1
C1OUT
RA4/T0CKI/C1OUT*
D
VIN-
RA2/AN2/ D
VREF-/CVREF
VIN+
RA1/AN1
RA0/AN0
A
RA3/AN3/
VREF+
A
RA1/AN1
A
VINVIN+
A
RA2/AN2/
VREF-/CVREF
C2
CIS = 0
CIS = 1
CIS = 0
CIS = 1
C1
C1OUT
C2
C2OUT
VINVIN+
Off (Read as ‘0’)
CVREF
From VREF Module
A = Analog Input, port reads zeros always
D = Digital Input
CIS (CMCON<3>) is the Comparator Input Switch
* Setting the TRISA<5:4> bits will disable the comparator outputs by configuring the pins as inputs.
DS39636A-page 222
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
19.2
19.3.2
Comparator Operation
A single comparator is shown in Figure 19-2, along with
the relationship between the analog input levels and
the digital output. When the analog input at VIN+ is less
than the analog input VIN-, the output of the comparator
is a digital low level. When the analog input at VIN+ is
greater than the analog input VIN-, the output of the
comparator is a digital high level. The shaded areas of
the output of the comparator in Figure 19-2 represent
the uncertainty, due to input offsets and response time.
19.3
Comparator Reference
Depending on the comparator operating mode, either
an external or internal voltage reference may be used.
The analog signal present at VIN- is compared to the
signal at VIN+ and the digital output of the comparator
is adjusted accordingly (Figure 19-2).
FIGURE 19-2:
SINGLE COMPARATOR
VIN+
+
VIN-
–
The internal reference is only available in the mode
where four inputs are multiplexed to two comparators
(CM2:CM0 = 110). In this mode, the internal voltage
reference is applied to the VIN+ pin of both
comparators.
19.4
Comparator Response Time
Response time is the minimum time, after selecting a
new reference voltage or input source, before the
comparator output has a valid level. If the internal
reference is changed, the maximum delay of the
internal voltage reference must be considered when
using the comparator outputs. Otherwise, the
maximum delay of the comparators should be used
(see Section 25.0 “Electrical Characteristics”).
Comparator Outputs
The comparator outputs are read through the CMCON
register. These bits are read-only. The comparator
outputs may also be directly output to the RA4 and RA5
I/O pins. When enabled, multiplexors in the output path
of the RA4 and RA5 pins will switch and the output of
each pin will be the unsynchronized output of the
comparator. The uncertainty of each of the
comparators is related to the input offset voltage and
the response time given in the specifications.
Figure 19-3 shows the comparator output block
diagram.
VINVIN+
Output
19.3.1
The comparator module also allows the selection of an
internally generated voltage reference from the
comparator voltage reference module. This module is
described in more detail in Section 20.0 “Comparator
Voltage Reference Module”.
19.5
Output
INTERNAL REFERENCE SIGNAL
The TRISA bits will still function as an output enable/
disable for the RA4 and RA5 pins while in this mode.
EXTERNAL REFERENCE SIGNAL
When external voltage references are used, the
comparator module can be configured to have the comparators operate from the same or different reference
sources. However, threshold detector applications may
require the same reference. The reference signal must
be between VSS and VDD and can be applied to either
pin of the comparator(s).
 2004 Microchip Technology Inc.
The polarity of the comparator outputs can be changed
using the C2INV and C1INV bits (CMCON<4:5>).
Note 1: When reading the Port register, all pins
configured as analog inputs will read as a
‘0’. Pins configured as digital inputs will
convert an analog input according to the
Schmitt Trigger input specification.
Preliminary
2: Analog levels on any pin defined as a
digital input may cause the input buffer to
consume more current than is specified.
DS39636A-page 223
PIC18F2X1X/4X1X
+
To RA4 or
RA5 pin
-
Port pins
COMPARATOR OUTPUT BLOCK DIAGRAM
MULTIPLEX
FIGURE 19-3:
D
Q
Bus
Data
CxINV
EN
Read CMCON
D
Q
EN
CL
From
other
Comparator
Reset
19.6
Comparator Interrupts
19.7
The comparator interrupt flag is set whenever there is
a change in the output value of either comparator.
Software will need to maintain information about the
status of the output bits, as read from CMCON<7:6>, to
determine the actual change that occurred. The CMIF
bit (PIR2<6>) is the Comparator Interrupt Flag. The
CMIF bit must be reset by clearing it. Since it is also
possible to write a ‘1’ to this register, a simulated
interrupt may be initiated.
Both the CMIE bit (PIE2<6>) and the PEIE bit
(INTCON<6>) must be set to enable the interrupt. In
addition, the GIE bit (INTCON<7>) must also be set. If
any of these bits are clear, the interrupt is not enabled,
though the CMIF bit will still be set if an interrupt
condition occurs.
Note:
If a change in the CMCON register
(C1OUT or C2OUT) should occur when a
read operation is being executed (start of
the Q2 cycle), then the CMIF (PIR
registers) interrupt flag may not get set.
The user, in the Interrupt Service Routine, can clear the
interrupt in the following manner:
a)
b)
Set
CMIF
bit
Comparator Operation
During Sleep
When a comparator is active and the device is placed
in Sleep mode, the comparator remains active and the
interrupt is functional if enabled. This interrupt will
wake-up the device from Sleep mode, when enabled.
Each operational comparator will consume additional
current, as shown in the comparator specifications. To
minimize power consumption while in Sleep mode, turn
off the comparators (CM2:CM0 = 111) before entering
Sleep. If the device wakes up from Sleep, the contents
of the CMCON register are not affected.
19.8
Effects of a Reset
A device Reset forces the CMCON register to its Reset
state, causing the comparator modules to be turned off
(CM2:CM0 = 111). However, the input pins (RA0
through RA3) are configured as analog inputs by
default on device Reset. The I/O configuration for these
pins is determined by the setting of the PCFG3:PCFG0
bits (ADCON1<3:0>). Therefore, device current is
minimized when analog inputs are present at Reset
time.
Any read or write of CMCON will end the
mismatch condition.
Clear flag bit CMIF.
A mismatch condition will continue to set flag bit CMIF.
Reading CMCON will end the mismatch condition and
allow flag bit CMIF to be cleared.
DS39636A-page 224
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
19.9
Analog Input Connection
Considerations
range by more than 0.6V in either direction, one of the
diodes is forward biased and a latch-up condition may
occur. A maximum source impedance of 10 kΩ is
recommended for the analog sources. Any external
component connected to an analog input pin, such as
a capacitor or a Zener diode, should have very little
leakage current.
A simplified circuit for an analog input is shown in
Figure 19-4. Since the analog pins are connected to a
digital output, they have reverse biased diodes to VDD
and VSS. The analog input, therefore, must be between
VSS and VDD. If the input voltage deviates from this
FIGURE 19-4:
COMPARATOR ANALOG INPUT MODEL
VDD
VT = 0.6V
RS < 10k
RIC
Comparator
Input
AIN
CPIN
5 pF
VA
VT = 0.6V
ILEAKAGE
±500 nA
VSS
Legend:
TABLE 19-1:
Name
CMCON
CVRCON
INTCON
CPIN
VT
ILEAKAGE
RIC
RS
VA
=
=
=
=
=
=
Input Capacitance
Threshold Voltage
Leakage Current at the pin due to various junctions
Interconnect Resistance
Source Impedance
Analog Voltage
REGISTERS ASSOCIATED WITH COMPARATOR MODULE
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
Values
on page
C2OUT
C1OUT
C2INV
C1INV
CIS
CM2
CM1
CM0
51
CVREN
CVROE
CVRR
CVRSS
CVR3
CVR2
CVR1
CVR0
51
TMR0IE
INT0IE
RBIE
TMR0IF
INT0IF
RBIF
52
CMIF
—
—
BCLIF
HLVDIF
TMR3IF
CCP2IF
52
GIE/GIEH PEIE/GIEL
PIR2
OSCFIF
PIE2
OCSFIE
CMIE
—
—
BCLIE
HLVDIE
TMR3IE
CCP2IE
52
IPR2
OSCFIP
CMIP
—
—
BCLIP
HLVDIP
TMR3IP
CCP2IP
52
RA7(1)
RA6(1)
RA5
RA4
RA3
RA2
RA1
RA0
52
LATA
LATA7(1)
LATA6(1)
TRISA
TRISA7(1)
TRISA6(1) PORTA Data Direction Control Register
PORTA
PORTA Data Latch Register (Read and Write to Data Latch)
52
52
Legend: — = unimplemented, read as ‘0’. Shaded cells are unused by the comparator module.
Note 1: PORTA<7:6> and their direction and latch bits are individually configured as port pins based on various
primary oscillator modes. When disabled, these bits read as ‘0’.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 225
PIC18F2X1X/4X1X
NOTES:
DS39636A-page 226
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
20.0
COMPARATOR VOLTAGE
REFERENCE MODULE
The comparator voltage reference is a 16-tap resistor
ladder network that provides a selectable reference
voltage. Although its primary purpose is to provide a
reference for the analog comparators, it may also be
used independently of them.
A block diagram of the module is shown in Figure 20-1.
The resistor ladder is segmented to provide two ranges
of CVREF values and has a power-down function to
conserve power when the reference is not being used.
The module’s supply reference can be provided from
either device VDD/VSS or an external voltage reference.
20.1
Configuring the Comparator
Voltage Reference
The voltage reference module is controlled through the
CVRCON register (Register 20-1). The comparator
voltage reference provides two ranges of output
voltage, each with 16 distinct levels. The range to be
REGISTER 20-1:
used is selected by the CVRR bit (CVRCON<5>). The
primary difference between the ranges is the size of the
steps selected by the CVREF selection bits
(CVR3:CVR0), with one range offering finer resolution.
The equations used to calculate the output of the
comparator voltage reference are as follows:
If CVRR = 1:
CVREF = ((CVR3:CVR0)/24) x CVRSRC
If CVRR = 0:
CVREF = (CVRSRC x 1/4) + (((CVR3:CVR0)/32) x
CVRSRC)
The comparator reference supply voltage can come
from either VDD and VSS, or the external VREF+ and
VREF- that are multiplexed with RA2 and RA3. The
voltage source is selected by the CVRSS bit
(CVRCON<4>).
The settling time of the comparator voltage reference
must be considered when changing the CVREF
output (see Table 25-3 in Section 25.0 “Electrical
Characteristics”).
CVRCON: COMPARATOR VOLTAGE REFERENCE CONTROL REGISTER
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
CVREN
CVROE(1)
CVRR
CVRSS
CVR3
CVR2
CVR1
CVR0
bit 7
bit 0
bit 7
CVREN: Comparator Voltage Reference Enable bit
1 = CVREF circuit powered on
0 = CVREF circuit powered down
bit 6
CVROE: Comparator VREF Output Enable bit(1)
1 = CVREF voltage level is also output on the RA2/AN2/VREF-/CVREF pin
0 = CVREF voltage is disconnected from the RA2/AN2/VREF-/CVREF pin
Note 1: CVROE overrides the TRISA<2> bit setting.
bit 5
CVRR: Comparator VREF Range Selection bit
1 = 0 to 0.667 CVRSRC, with CVRSRC/24 step size (low range)
0 = 0.25 CVRSRC to 0.75 CVRSRC, with CVRSRC/32 step size (high range)
bit 4
CVRSS: Comparator VREF Source Selection bit
1 = Comparator reference source, CVRSRC = (VREF+) – (VREF-)
0 = Comparator reference source, CVRSRC = VDD – VSS
bit 3-0
CVR3:CVR0: Comparator VREF Value Selection bits (0 ≤ (CVR3:CVR0) ≤ 15)
When CVRR = 1:
CVREF = ((CVR3:CVR0)/24) • (CVRSRC)
When CVRR = 0:
CVREF = (CVRSRC/4) + ((CVR3:CVR0)/32) • (CVRSRC)
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
 2004 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS39636A-page 227
PIC18F2X1X/4X1X
FIGURE 20-1:
COMPARATOR VOLTAGE REFERENCE BLOCK DIAGRAM
VREF+
VDD
CVRSS = 1
8R
CVRSS = 0
CVR3:CVR0
R
CVREN
R
16-to-1 MUX
R
R
16 Steps
CVREF
R
R
R
CVRR
VREF-
8R
CVRSS = 1
CVRSS = 0
20.2
Voltage Reference Accuracy/Error
The full range of voltage reference cannot be realized
due to the construction of the module. The transistors
on the top and bottom of the resistor ladder network
(Figure 20-1) keep CVREF from approaching the reference source rails. The voltage reference is derived
from the reference source; therefore, the CVREF output
changes with fluctuations in that source. The tested
absolute accuracy of the voltage reference can be
found in Section 25.0 “Electrical Characteristics”.
20.3
Operation During Sleep
When the device wakes up from Sleep through an
interrupt or a Watchdog Timer time-out, the contents of
the CVRCON register are not affected. To minimize
current consumption in Sleep mode, the voltage
reference should be disabled.
20.4
Effects of a Reset
A device Reset disables the voltage reference by
clearing bit CVREN (CVRCON<7>). This Reset also
disconnects the reference from the RA2 pin by clearing
bit CVROE (CVRCON<6>) and selects the high-voltage
range by clearing bit CVRR (CVRCON<5>). The CVR
value select bits are also cleared.
20.5
Connection Considerations
The voltage reference module operates independently
of the comparator module. The output of the reference
generator may be connected to the RA2 pin if the
CVROE bit is set. Enabling the voltage reference output onto RA2 when it is configured as a digital input will
increase current consumption. Connecting RA2 as a
digital output with CVRSS enabled will also increase
current consumption.
The RA2 pin can be used as a simple D/A output with
limited drive capability. Due to the limited current drive
capability, a buffer must be used on the voltage
reference output for external connections to VREF.
Figure 20-2 shows an example buffering technique.
DS39636A-page 228
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
FIGURE 20-2:
COMPARATOR VOLTAGE REFERENCE OUTPUT BUFFER EXAMPLE
PIC18FXXXX
CVREF
Module
R(1)
Voltage
Reference
Output
Impedance
Note 1:
TABLE 20-1:
Name
CVREF Output
R is dependent upon the voltage reference configuration bits, CVRCON<3:0> and CVRCON<5>.
REGISTERS ASSOCIATED WITH COMPARATOR VOLTAGE REFERENCE
Bit 7
Bit 6
CVRCON
CVREN
CMCON
C2OUT
TRISA
+
–
RA2
Reset
Values
on page
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
CVROE
CVRR
CVRSS
CVR3
CVR2
CVR1
CVR0
51
C1OUT
C2INV
C1INV
CIS
CM2
CM1
CM0
51
TRISA7(1) TRISA6(1) PORTA Data Direction Control Register
52
Legend: Shaded cells are not used with the comparator voltage reference.
Note 1: PORTA pins are enabled based on oscillator configuration.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 229
PIC18F2X1X/4X1X
NOTES:
DS39636A-page 230
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
21.0
HIGH/LOW-VOLTAGE DETECT
(HLVD)
PIC18F2X1X/4X1X devices have a High/Low-Voltage
Detect module (HLVD). This is a programmable circuit
that allows the user to specify both a device voltage trip
point and the direction of change from that point. If the
device experiences an excursion past the trip point in
that direction, an interrupt flag is set. If the interrupt is
enabled, the program execution will branch to the interrupt vector address and the software can then respond
to the interrupt.
REGISTER 21-1:
The High/Low-Voltage Detect Control register
(Register 21-1) completely controls the operation of the
HLVD module. This allows the circuitry to be “turned
off” by the user under software control, which
minimizes the current consumption for the device.
The block diagram for the HLVD module is shown in
Figure 21-1.
HLVDCON: HIGH/LOW-VOLTAGE DETECT CONTROL REGISTER
R/W-0
U-0
R-0
R/W-0
R/W-0
R/W-1
R/W-0
R/W-1
VDIRMAG
—
IRVST
HLVDEN
HLVDL3
HLVDL2
HLVDL1
HLVDL0
bit 7
bit 0
bit 7
VDIRMAG: Voltage Direction Magnitude Select bit
1 = Event occurs when voltage equals or exceeds trip point (HLVDL3:HLDVL0)
0 = Event occurs when voltage equals or falls below trip point (HLVDL3:HLVDL0)
bit 6
Unimplemented: Read as ‘0’
bit 5
IRVST: Internal Reference Voltage Stable Flag bit
1 = Indicates that the voltage detect logic will generate the interrupt flag at the specified voltage
range
0 = Indicates that the voltage detect logic will not generate the interrupt flag at the specified
voltage range and the HLVD interrupt should not be enabled
bit 4
HLVDEN: High/Low-Voltage Detect Power Enable bit
1 = HLVD enabled
0 = HLVD disabled
bit 3-0
HLVDL3:HLVDL0: Voltage Detection Limit bits
1111 = External analog input is used (input comes from the HLVDIN pin)
1110 = Maximum setting
.
.
.
0000 = Minimum setting
Note:
See Table 25-4 in Section 25.0 “Electrical Characteristics” for the specifications.
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
 2004 Microchip Technology Inc.
x = Bit is unknown
DS39636A-page 231
PIC18F2X1X/4X1X
The module is enabled by setting the HLVDEN bit.
Each time that the HLVD module is enabled, the
circuitry requires some time to stabilize. The IRVST bit
is a read-only bit and is used to indicate when the circuit
is stable. The module can only generate an interrupt
after the circuit is stable and IRVST is set.
event, depending on the configuration of the module.
When the supply voltage is equal to the trip point, the
voltage tapped off of the resistor array is equal to the
internal reference voltage generated by the voltage
reference module. The comparator then generates an
interrupt signal by setting the HLVDIF bit.
The VDIRMAG bit determines the overall operation of
the module. When VDIRMAG is cleared, the module
monitors for drops in VDD below a predetermined set
point. When the bit is set, the module monitors for rises
in VDD above the set point.
The trip point voltage is software programmable to any
one of 16 values. The trip point is selected by
programming
the
HLVDL3:HLVDL0
bits
(HLVDCON<3:0>).
21.1
Operation
When the HLVD module is enabled, a comparator uses
an internally generated reference voltage as the set
point. The set point is compared with the trip point,
where each node in the resistor divider represents a
trip point voltage. The “trip point” voltage is the voltage
level at which the device detects a high or low-voltage
FIGURE 21-1:
The HLVD module has an additional feature that allows
the user to supply the trip voltage to the module from an
external source. This mode is enabled when bits
HLVDL3:HLVDL0 are set to ‘1111’. In this state, the
comparator input is multiplexed from the external input
pin, HLVDIN. This gives users flexibility because it
allows them to configure the High/Low-Voltage Detect
interrupt to occur at any voltage in the valid operating
range.
HLVD MODULE BLOCK DIAGRAM (WITH EXTERNAL INPUT)
Externally Generated
Trip Point
VDD
VDD
HLVDCON
Register
HLVDEN
HLVDIN
16 to 1 MUX
HLVDIN
HLVDL3:HLVDL0
VDIRMAG
Set
HLVDIF
HLVDEN
BOREN
DS39636A-page 232
Internal Voltage
Reference
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
21.2
HLVD Setup
Depending on the application, the HLVD module does
not need to be operating constantly. To decrease the
current requirements, the HLVD circuitry may only
need to be enabled for short periods where the voltage
is checked. After doing the check, the HLVD module
may be disabled.
The following steps are needed to set up the HLVD
module:
1.
2.
3.
4.
5.
6.
Disable the module by clearing the HLVDEN bit
(HLVDCON<4>).
Write the value to the HLVDL3:HLVDL0 bits that
selects the desired HLVD trip point.
Set the VDIRMAG bit to detect high voltage
(VDIRMAG = 1) or low voltage (VDIRMAG = 0).
Enable the HLVD module by setting the
HLVDEN bit.
Clear the HLVD interrupt flag (PIR2<2>), which
may have been set from a previous interrupt.
Enable the HLVD interrupt if interrupts are
desired by setting the HLVDIE and GIE bits
(PIE<2> and INTCON<7>). An interrupt will not
be generated until the IRVST bit is set.
21.3
21.4
The internal reference voltage of the HLVD module,
specified in electrical specification parameter D420,
may be used by other internal circuitry, such as the
Programmable Brown-out Reset. If the HLVD or other
circuits using the voltage reference are disabled to
lower the device’s current consumption, the reference
voltage circuit will require time to become stable before
a low or high-voltage condition can be reliably
detected. This start-up time, TIRVST, is an interval that
is independent of device clock speed. It is specified in
electrical specification parameter 36.
Current Consumption
The HLVD interrupt flag is not enabled until TIRVST has
expired and a stable reference voltage is reached. For
this reason, brief excursions beyond the set point may
not be detected during this interval. Refer to
Figure 21-2 or Figure 21-3.
When the module is enabled, the HLVD comparator
and voltage divider are enabled and will consume static
current. The total current consumption, when enabled,
is specified in electrical specification parameter D022B.
FIGURE 21-2:
HLVD Start-up Time
LOW-VOLTAGE DETECT OPERATION (VDIRMAG = 0)
CASE 1:
HLVDIF may not be set
VDD
VLVD
HLVDIF
Enable HLVD
TIVRST
IRVST
Internal Reference is stable
HLVDIF cleared in software
CASE 2:
VDD
VLVD
HLVDIF
Enable HLVD
TIVRST
IRVST
Internal Reference is stable
HLVDIF cleared in software
HLVDIF cleared in software,
HLVDIF remains set since HLVD condition still exists
 2004 Microchip Technology Inc.
DS39636A-page 233
PIC18F2X1X/4X1X
FIGURE 21-3:
HIGH-VOLTAGE DETECT OPERATION (VDIRMAG = 1)
CASE 1:
HLVDIF may not be set
VLVD
VDD
HLVDIF
Enable HLVD
TIVRST
IRVST
HLVDIF cleared in software
Internal Reference is stable
CASE 2:
VLVD
VDD
HLVDIF
Enable HLVD
TIVRST
IRVST
Internal Reference is stable
HLVDIF cleared in software
HLVDIF cleared in software,
HLVDIF remains set since HLVD condition still exists
Applications
In many applications, the ability to detect a drop below
or rise above a particular threshold is desirable. For
example, the HLVD module could be periodically
enabled to detect a Universal Serial Bus (USB) attach
or detach. This assumes the device is powered by a
lower voltage source than the USB when detached. An
attach would indicate a high-voltage detect from, for
example, 3.3V to 5V (the voltage on USB) and vice
versa for a detach. This feature could save a design a
few extra components and an attach signal (input pin).
For general battery applications, Figure 21-4 shows a
possible voltage curve. Over time, the device voltage
decreases. When the device voltage reaches voltage
VA, the HLVD logic generates an interrupt at time TA.
The interrupt could cause the execution of an ISR,
which would allow the application to perform “housekeeping tasks” and perform a controlled shutdown
before the device voltage exits the valid operating
range at TB. The HLVD thus would give the application
a time window, represented by the difference between
TA and TB, to safely exit.
DS39636A-page 234
FIGURE 21-4:
TYPICAL
HIGH/LOW-VOLTAGE
DETECT APPLICATION
VA
VB
Voltage
21.5
Time
TA
TB
Legend: VA = HLVD trip point
VB = Minimum valid device
operating voltage
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
21.6
Operation During Sleep
21.7
When enabled, the HLVD circuitry continues to operate
during Sleep. If the device voltage crosses the trip
point, the HLVDIF bit will be set and the device will
wake-up from Sleep. Device execution will continue
from the interrupt vector address if interrupts have
been globally enabled.
TABLE 21-1:
Effects of a Reset
A device Reset forces all registers to their Reset state.
This forces the HLVD module to be turned off.
REGISTERS ASSOCIATED WITH HIGH/LOW-VOLTAGE DETECT MODULE
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
Values
on Page
HLVDCON
VDIRMAG
—
IRVST
HLVDEN
HLVDL3
HLVDL2
HLVDL1
HLVDL0
50
INTCON
GIE/GIEH PEIE/GIEL
TMR0IE
INT0IE
RBIE
TMR0IF
INT0IF
RBIF
49
PIR2
OSCFIF
CMIF
—
—
BCLIF
HLVDIF
TMR3IF
CCP2IF
52
PIE2
OCSFIE
CMIE
—
—
BCLIE
HLVDIE
TMR3IE
CCP2IE
52
IPR2
OSCFIP
CMIP
—
—
BCLIP
HLVDIP
TMR3IP
CCP2IP
52
Legend: — = unimplemented, read as ‘0’. Shaded cells are unused by the HLVD module.
 2004 Microchip Technology Inc.
DS39636A-page 235
PIC18F2X1X/4X1X
NOTES:
DS39636A-page 236
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
22.0
SPECIAL FEATURES OF
THE CPU
A complete discussion of device Resets and interrupts
is available in previous sections of this data sheet.
PIC18F2X1X/4X1X devices include several features
intended to maximize reliability and minimize cost
through elimination of external components. These are:
In addition to their Power-up and Oscillator Start-up
Timers provided for Resets, PIC18F2X1X/4X1X
devices have a Watchdog Timer, which is either
permanently enabled via the configuration bits or
software controlled (if configured as disabled).
• Oscillator Selection
• Resets:
- Power-on Reset (POR)
- Power-up Timer (PWRT)
- Oscillator Start-up Timer (OST)
- Brown-out Reset (BOR)
• Interrupts
• Watchdog Timer (WDT)
• Fail-Safe Clock Monitor
• Two-Speed Start-up
• Code Protection
• ID Locations
• In-Circuit Serial Programming
The inclusion of an internal RC oscillator also provides
the additional benefits of a Fail-Safe Clock Monitor
(FSCM) and Two-Speed Start-up. FSCM provides for
background monitoring of the peripheral clock and
automatic switchover in the event of its failure. TwoSpeed Start-up enables code to be executed almost
immediately on start-up, while the primary clock source
completes its start-up delays.
All of these features are enabled and configured by
setting the appropriate configuration register bits.
22.1
The oscillator can be configured for the application
depending on frequency, power, accuracy and cost. All
of the options are discussed in detail in Section 2.0
“Oscillator Configurations”.
TABLE 22-1:
The configuration bits can be programmed (read as ‘0’)
or left unprogrammed (read as ‘1’) to select various
device configurations. These bits are mapped starting
at program memory location 300000h.
The user will note that address 300000h is beyond the
user program memory space. In fact, it belongs to the
configuration memory space (300000h-3FFFFFh), which
can only be accessed using table reads.
CONFIGURATION BITS AND DEVICE IDs
File Name
300001h
Configuration Bits
Default/
Unprogrammed
Value
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
CONFIG1H
IESO
FCMEN
—
—
FOSC3
FOSC2
FOSC1
FOSC0
00-- 0111
---1 1111
300002h
CONFIG2L
—
—
—
BORV1
BORV0
BOREN1
BOREN0
PWRTEN
300003h
CONFIG2H
—
—
—
WDTPS3
WDTPS2
WDTPS1
WDTPS0
WDTEN
---1 1111
300005h
CONFIG3H
MCLRE
—
—
—
—
LPT1OSC
PBADEN
CCP2MX
1--- -011
10-- -1-1
300006h
CONFIG4L
DEBUG
XINST
—
—
—
LVP
—
STVREN
300008h
CONFIG5L
—
—
—
—
CP3(1,2)
CP2(1)
CP1
CP0
---- 1111
300009h
CONFIG5H
—
CPB
—
—
—
—
—
—
-1-- ----
30000Ah
CONFIG6L
—
—
—
—
WRT3(1,2)
WRT2(1)
WRT1
WRT0
---- 1111
30000Bh
CONFIG6H
—
WRTB
WRTC
—
—
—
—
—
-11- ----
30000Ch
CONFIG7L
—
—
—
—
EBTR3(1,2)
EBTR2(1)
EBTR1
EBTR0
---- 1111
30000Dh
CONFIG7H
—
EBTRB
—
—
—
—
—
—
-1-- ----
3FFFFEh
DEVID1(3)
DEV2
DEV1
DEV0
REV4
REV3
REV2
REV1
REV0
xxxx xxxx(3)
3FFFFFh
DEVID2(3)
DEV10
DEV9
DEV8
DEV7
DEV6
DEV5
DEV4
DEV3
0000 1100
Legend:
x = unknown, u = unchanged, — = unimplemented, q = value depends on condition.
Shaded cells are unimplemented, read as ‘0’.
Unimplemented in PIC18F2410/4410 devices; maintain this bit set.
Unimplemented in PIC18F2515/4515 devices, maintain this bit set.
See Register 22-14 for DEVID1 values. DEVID registers are read-only and cannot be programmed by the user.
Note
1:
2:
3:
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 237
PIC18F2X1X/4X1X
REGISTER 22-1:
CONFIG1H: CONFIGURATION REGISTER 1 HIGH (BYTE ADDRESS 300001h)
R/P-0
R/P-0
U-0
U-0
R/P-0
R/P-1
R/P-1
R/P-1
IESO
FCMEN
—
—
FOSC3
FOSC2
FOSC1
FOSC0
bit 7
bit 0
bit 7
IESO: Internal/External Oscillator Switchover bit
1 = Oscillator Switchover mode enabled
0 = Oscillator Switchover mode disabled
bit 6
FCMEN: Fail-Safe Clock Monitor Enable bit
1 = Fail-Safe Clock Monitor enabled
0 = Fail-Safe Clock Monitor disabled
bit 5-4
Unimplemented: Read as ‘0’
bit 3-0
FOSC3:FOSC0: Oscillator Selection bits
11xx = External RC oscillator, CLKO function on RA6
101x = External RC oscillator, CLKO function on RA6
1001 = Internal oscillator block, CLKO function on RA6, port function on RA7
1000 = Internal oscillator block, port function on RA6 and RA7
0111 = External RC oscillator, port function on RA6
0110 = HS oscillator, PLL enabled (Clock Frequency = 4 x FOSC1)
0101 = EC oscillator, port function on RA6
0100 = EC oscillator, CLKO function on RA6
0011 = External RC oscillator, CLKO function on RA6
0010 = HS oscillator
0001 = XT oscillator
0000 = LP oscillator
Legend:
R = Readable bit
P = Programmable bit
-n = Value when device is unprogrammed
DS39636A-page 238
Preliminary
U = Unimplemented bit, read as ‘0’
u = Unchanged from programmed state
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
REGISTER 22-2:
CONFIG2L: CONFIGURATION REGISTER 2 LOW (BYTE ADDRESS 300002h)
U-0
U-0
—
—
U-0
R/P-1
—
BORV1
(1)
R/P-1
BORV0
(1)
R/P-1
R/P-1
(2)
BOREN1
R/P-1
(2)
BOREN0
PWRTEN(2)
bit 7
bit 0
bit 7-5
Unimplemented: Read as ‘0’
bit 4-3
BORV1:BORV0: Brown-out Reset Voltage bits(1)
11 = Minimum setting
.
.
.
00 = Maximum setting
bit 2-1
BOREN1:BOREN0: Brown-out Reset Enable bits(2)
11 = Brown-out Reset enabled in hardware only (SBOREN is disabled)
10 = Brown-out Reset enabled in hardware only and disabled in Sleep mode
(SBOREN is disabled)
01 = Brown-out Reset enabled and controlled by software (SBOREN is enabled)
00 = Brown-out Reset disabled in hardware and software
bit 0
PWRTEN: Power-up Timer Enable bit(2)
1 = PWRT disabled
0 = PWRT enabled
Note 1: See Section 25.1 “DC Characteristics” for the specifications.
2: The Power-up Timer is decoupled from Brown-out Reset, allowing these features to
be independently controlled.
Legend:
R = Readable bit
P = Programmable bit
-n = Value when device is unprogrammed
 2004 Microchip Technology Inc.
Preliminary
U = Unimplemented bit, read as ‘0’
u = Unchanged from programmed state
DS39636A-page 239
PIC18F2X1X/4X1X
REGISTER 22-3:
CONFIG2H: CONFIGURATION REGISTER 2 HIGH (BYTE ADDRESS 300003h)
U-0
U-0
U-0
R/P-1
R/P-1
R/P-1
R/P-1
R/P-1
—
—
—
WDTPS3
WDTPS2
WDTPS1
WDTPS0
WDTEN
bit 7
bit 0
bit 7-5
Unimplemented: Read as ‘0’
bit 4-1
WDTPS3:WDTPS0: Watchdog Timer Postscale Select bits
1111 = 1:32,768
1110 = 1:16,384
1101 = 1:8,192
1100 = 1:4,096
1011 = 1:2,048
1010 = 1:1,024
1001 = 1:512
1000 = 1:256
0111 = 1:128
0110 = 1:64
0101 = 1:32
0100 = 1:16
0011 = 1:8
0010 = 1:4
0001 = 1:2
0000 = 1:1
bit 0
WDTEN: Watchdog Timer Enable bit
1 = WDT enabled
0 = WDT disabled (control is placed on the SWDTEN bit)
Legend:
R = Readable bit
P = Programmable bit
-n = Value when device is unprogrammed
DS39636A-page 240
Preliminary
U = Unimplemented bit, read as ‘0’
u = Unchanged from programmed state
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
REGISTER 22-4:
CONFIG3H: CONFIGURATION REGISTER 3 HIGH (BYTE ADDRESS 300005h)
R/P-1
U-0
U-0
U-0
U-0
R/P-0
R/P-1
R/P-1
MCLRE
—
—
—
—
LPT1OSC
PBADEN
CCP2MX
bit 7
bit 0
bit 7
MCLRE: MCLR Pin Enable bit
1 = MCLR pin enabled; RE3 input pin disabled
0 = RE3 input pin enabled; MCLR disabled
bit 6-3
Unimplemented: Read as ‘0’
bit 2
LPT1OSC: Low-Power Timer1 Oscillator Enable bit
1 = Timer1 configured for low-power operation
0 = Timer1 configured for higher power operation
bit 1
PBADEN: PORTB A/D Enable bit
(Affects ADCON1 Reset state. ADCON1 controls PORTB<4:0> pin configuration.)
1 = PORTB<4:0> pins are configured as analog input channels on Reset
0 = PORTB<4:0> pins are configured as digital I/O on Reset
bit 0
CCP2MX: CCP2 Mux bit
1 = CCP2 input/output is multiplexed with RC1
0 = CCP2 input/output is multiplexed with RB3
Legend:
R = Readable bit
P = Programmable bit
-n = Value when device is unprogrammed
REGISTER 22-5:
U = Unimplemented bit, read as ‘0’
u = Unchanged from programmed state
CONFIG4L: CONFIGURATION REGISTER 4 LOW (BYTE ADDRESS 300006h)
R/P-1
R/P-0
U-0
U-0
U-0
R/P-1
U-0
R/P-1
DEBUG
XINST
—
—
—
LVP
—
STVREN
bit 7
bit 0
bit 7
DEBUG: Background Debugger Enable bit
1 = Background debugger disabled, RB6 and RB7 configured as general purpose I/O pins
0 = Background debugger enabled, RB6 and RB7 are dedicated to In-Circuit Debug
bit 6
XINST: Extended Instruction Set Enable bit
1 = Instruction set extension and Indexed Addressing mode enabled
0 = Instruction set extension and Indexed Addressing mode disabled (Legacy mode)
bit 5-3
Unimplemented: Read as ‘0’
bit 2
LVP: Single-Supply ICSP Enable bit
1 = Single-Supply ICSP enabled
0 = Single-Supply ICSP disabled
bit 1
Unimplemented: Read as ‘0’
bit 0
STVREN: Stack Full/Underflow Reset Enable bit
1 = Stack full/underflow will cause Reset
0 = Stack full/underflow will not cause Reset
Legend:
R = Readable bit
C = Clearable bit
-n = Value when device is unprogrammed
 2004 Microchip Technology Inc.
Preliminary
U = Unimplemented bit, read as ‘0’
u = Unchanged from programmed state
DS39636A-page 241
PIC18F2X1X/4X1X
REGISTER 22-6:
CONFIG5L: CONFIGURATION REGISTER 5 LOW (BYTE ADDRESS 300008h)
U-0
U-0
U-0
U-0
R/C-1
R/C-1
R/C-1
R/C-1
—
—
—
—
CP3(1,2)
CP2(1)
CP1
CP0
bit 7
bit 0
bit 7-4
Unimplemented: Read as ‘0’
bit 3
CP3: Code Protection bit(1,2)
1 = Block 3 (006000-007FFFh) not code-protected(3)
0 = Block 3 (006000-007FFFh) code-protected(3)
1 = Block 3 (00C000-00FFFFh) not code-protected(4)
0 = Block 3 (00C000-00FFFFh) code-protected(4)
bit 2
CP2: Code Protection bit(1)
1 = Block 2 (004000-005FFFh) not code-protected(3)
0 = Block 2 (004000-005FFFh) code-protected(3)
1 = Block 2 (008000-00BFFFh) not code-protected(4)
0 = Block 2 (008000-00BFFFh) code-protected(4)
bit 1
CP1: Code Protection bit
1 = Block 1 (002000-003FFFh) not code-protected(3)
0 = Block 1 (002000-003FFFh) code-protected(3)
1 = Block 1 (004000-007FFFh) not code-protected(4)
0 = Block 1 (004000-007FFFh) code-protected(4)
bit 0
CP0: Code Protection bit
1 = Block 0 (000800-001FFFh) not code-protected(3)
0 = Block 0 (000800-001FFFh) code-protected(3)
1 = Block 0 (000800-003FFFh) not code-protected(4)
0 = Block 0 (000800-003FFFh) code-protected(4)
Note 1:
2:
3:
4:
Unimplemented in PIC18F2410/4410 devices; maintain this bit set.
Unimplemented in PIC18F2515/4515 devices; maintain this bit set.
Address range for 16K and 32K devices.
Address range for 48K and 64K devices.
Legend:
R = Readable bit
C = Clearable bit
-n = Value when device is unprogrammed
REGISTER 22-7:
U = Unimplemented bit, read as ‘0’
u = Unchanged from programmed state
CONFIG5H: CONFIGURATION REGISTER 5 HIGH (BYTE ADDRESS 300009h)
U-0
R/C-1
U-0
U-0
U-0
U-0
U-0
U-0
—
CPB
—
—
—
—
—
—
bit 7
bit 0
bit 7
Unimplemented: Read as ‘0’
bit 6
CPB: Boot Block Code Protection bit
1 = Boot block (000000-0007FFh) not code-protected
0 = Boot block (000000-0007FFh) code-protected
bit 5-0
Unimplemented: Read as ‘0’
Legend:
R = Readable bit
C = Clearable bit
-n = Value when device is unprogrammed
DS39636A-page 242
Preliminary
U = Unimplemented bit, read as ‘0’
u = Unchanged from programmed state
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
REGISTER 22-8:
CONFIG6L: CONFIGURATION REGISTER 6 LOW (BYTE ADDRESS 30000Ah)
U-0
—
U-0
—
U-0
—
U-0
—
R/C-1
WRT3
(1,2)
R/C-1
WRT2
(1)
R/C-1
R/C-1
WRT1
WRT0
bit 7
bit 0
bit 7-4
Unimplemented: Read as ‘0’
bit 3
WRT3: Write Protection bit(1,2)
1 = Block 3 (006000-007FFFh) not write-protected(3)
0 = Block 3 (006000-007FFFh) write-protected(3)
1 = Block 3 (00C000-00FFFFh) not write-protected(4)
0 = Block 3 (00C000-00FFFFh) write-protected(4)
bit 2
WRT2: Write Protection bit(1)
1 = Block 2 (004000-005FFFh) not write-protected(3)
0 = Block 2 (004000-005FFFh) write-protected(3)
1 = Block 2 (008000-00BFFFh) not write-protected(4)
0 = Block 2 (008000-00BFFFh) write-protected(4)
bit 1
WRT1: Write Protection bit
1 = Block 1 (002000-003FFFh) not write-protected(3)
0 = Block 1 (002000-003FFFh) write-protected(3)
1 = Block 1 (004000-007FFFh) not write-protected(4)
0 = Block 1 (004000-007FFFh) write-protected(4)
bit 0
WRT0: Write Protection bit
1 = Block 0 (000800-001FFFh) not write-protected(3)
0 = Block 0 (000800-001FFFh) write-protected(3)
1 = Block 0 (000800-003FFFh) not write-protected(4)
0 = Block 0 (000800-003FFFh) write-protected(4)
Note 1:
2:
3:
4:
Unimplemented in PIC18F2410/4410 devices; maintain this bit set.
Unimplemented in PIC18F2515/4515 devices; maintain this bit set.
Address range for 16K and 32K devices.
Address range for 48K and 64K devices.
Legend:
R = Readable bit
C = Clearable bit
-n = Value when device is unprogrammed
REGISTER 22-9:
U = Unimplemented bit, read as ‘0’
u = Unchanged from programmed state
CONFIG6H: CONFIGURATION REGISTER 6 HIGH (BYTE ADDRESS 30000Bh)
U-0
—
R/C-1
R-1
U-0
U-0
U-0
U-0
U-0
WRTB
WRTC(1)
—
—
—
—
—
bit 7
bit 0
bit 7
Unimplemented: Read as ‘0’
bit 6
WRTB: Boot Block Write Protection bit
1 = Boot block (000000-0007FFh) not write-protected
0 = Boot block (000000-0007FFh) write-protected
bit 5
WRTC: Configuration Register Write Protection bit(1)
1 = Configuration registers (300000-3000FFh) not write-protected
0 = Configuration registers (300000-3000FFh) write-protected
Note 1: This bit is read-only in normal execution mode; it can be written only in Program mode.
bit 4-0
Unimplemented: Read as ‘0’
Legend:
R = Readable bit
C = Clearable bit
-n = Value when device is unprogrammed
 2004 Microchip Technology Inc.
Preliminary
U = Unimplemented bit, read as ‘0’
u = Unchanged from programmed state
DS39636A-page 243
PIC18F2X1X/4X1X
REGISTER 22-10: CONFIG7L: CONFIGURATION REGISTER 7 LOW (BYTE ADDRESS 30000Ch)
U-0
U-0
U-0
U-0
R/C-1
R/C-1
R/C-1
R/C-1
—
—
—
—
EBTR3(1,2)
EBTR2(1)
EBTR1
EBTR0
bit 7
bit 0
bit 7-4
Unimplemented: Read as ‘0’
bit 3
EBTR3: Table Read Protection bit(1,2)
1 = Block 3 (006000-007FFFh) not protected from table reads executed in other blocks(3)
0 = Block 3 (006000-007FFFh) protected from table reads executed in other blocks(3)
1 = Block 3 (00C000-00FFFFh) not protected from table reads executed in other blocks(4)
0 = Block 3 (00C000-00FFFFh) protected from table reads executed in other blocks(4)
bit 2
EBTR2: Table Read Protection bit(1)
1 = Block 2 (004000-005FFFh) not protected from table reads executed in other blocks(3)
0 = Block 2 (004000-005FFFh) protected from table reads executed in other blocks(3)
1 = Block 2 (008000-00BFFFh) not protected from table reads executed in other blocks(4)
0 = Block 2 (008000-00BFFFh) protected from table reads executed in other blocks(4)
bit 1
EBTR1: Table Read Protection bit
1 = Block 1 (002000-003FFFh) not protected from table reads executed in other blocks(3)
0 = Block 1 (002000-003FFFh) protected from table reads executed in other blocks(3)
1 = Block 1 (004000-007FFFh) not protected from table reads executed in other blocks(4)
0 = Block 1 (004000-007FFFh) protected from table reads executed in other blocks(4)
bit 0
EBTR0: Table Read Protection bit
1 = Block 0 (000800-001FFFh) not protected from table reads executed in other blocks(3)
0 = Block 0 (000800-001FFFh) protected from table reads executed in other blocks(3)
1 = Block 0 (000800-003FFFh) not protected from table reads executed in other blocks(4)
0 = Block 0 (000800-003FFFh) protected from table reads executed in other blocks(4)
Note 1:
2:
3:
4:
Unimplemented in PIC18F2410/4410 devices; maintain this bit set.
Unimplemented in PIC18F2515/4515 devices; maintain this bit set.
Address range for 16K and 32K devices.
Address range for 48K and 64K devices.
Legend:
R = Readable bit
C = Clearable bit
-n = Value when device is unprogrammed
U = Unimplemented bit, read as ‘0’
u = Unchanged from programmed state
REGISTER 22-11: CONFIG7H: CONFIGURATION REGISTER 7 HIGH (BYTE ADDRESS 30000Dh)
U-0
R/C-1
U-0
U-0
U-0
U-0
U-0
U-0
—
EBTRB
—
—
—
—
—
—
bit 7
bit 0
bit 7
Unimplemented: Read as ‘0’
bit 6
EBTRB: Boot Block Table Read Protection bit
1 = Boot block (000000-0007FFh) not protected from table reads executed in other blocks
0 = Boot block (000000-0007FFh) protected from table reads executed in other blocks
bit 5-0
Unimplemented: Read as ‘0’
Legend:
R = Readable bit
C = Clearable bit
-n = Value when device is unprogrammed
DS39636A-page 244
Preliminary
U = Unimplemented bit, read as ‘0’
u = Unchanged from programmed state
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
REGISTER 22-12:
DEVICE ID REGISTER 1 FOR PIC18F2X1X/4X1X DEVICES
R
R
R
R
R
R
R
R
DEV2
DEV1
DEV0
REV4
REV3
REV2
REV1
REV0
bit 7
bit 0
bit 7-5
DEV2:DEV0: Device ID bits
011 = PIC18F2410
001 = PIC18F2510
111 = PIC18F2515
101 = PIC18F2610
111 = PIC18F4410
101 = PIC18F4510
011 = PIC18F4515
001 = PIC18F4610
bit 4-0
REV4:REV0: Revision ID bits
These bits are used to indicate the device revision.
Legend:
R = Read-only bit
P = Programmable bit
-n = Value when device is unprogrammed
U = Unimplemented bit, read as ‘0’
u = Unchanged from programmed state
REGISTER 22-13: DEVICE ID REGISTER 2 FOR PIC18F2X1X/4X1X DEVICES
R
R
R
R
R
R
R
R
DEV10
DEV9
DEV8
DEV7
DEV6
DEV5
DEV4
DEV3
bit 7
bit 7-0
bit 0
DEV10:DEV3: Device ID bits
These bits are used with the DEV2:DEV0 bits in the Device ID Register 1 to identify the
part number.
0000 1100 = PIC18F2X1X/4X1X devices
Note:
These values for DEV10:DEV3 may be shared with other devices. The specific
device is always identified by using the entire DEV10:DEV0 bit sequence.
Legend:
R = Read-only bit
P = Programmable bit
-n = Value when device is unprogrammed
 2004 Microchip Technology Inc.
Preliminary
U = Unimplemented bit, read as ‘0’
u = Unchanged from programmed state
DS39636A-page 245
PIC18F2X1X/4X1X
22.2
Watchdog Timer (WDT)
For PIC18F2X1X/4X1X devices, the WDT is driven by
the INTRC source. When the WDT is enabled, the
clock source is also enabled. The nominal WDT period
is 4 ms and has the same stability as the INTRC
oscillator.
The 4 ms period of the WDT is multiplied by a 16-bit
postscaler. Any output of the WDT postscaler is
selected by a multiplexer, controlled by bits in Configuration Register 2H. Available periods range from 4 ms
to 131.072 seconds (2.18 minutes). The WDT and
postscaler are cleared when any of the following events
occur: a SLEEP or CLRWDT instruction is executed, the
IRCF bits (OSCCON<6:4>) are changed or a clock
failure has occurred.
FIGURE 22-1:
SWDTEN
WDTEN
Note 1: The CLRWDT and SLEEP instructions
clear the WDT and postscaler counts
when executed.
2: Changing the setting of the IRCF bits
(OSCCON<6:4>) clears the WDT and
postscaler counts.
3: When a CLRWDT instruction is executed,
the postscaler count will be cleared.
22.2.1
CONTROL REGISTER
Register 22-14 shows the WDTCON register. This is a
readable and writable register which contains a control
bit that allows software to override the WDT enable
configuration bit, but only if the configuration bit has
disabled the WDT.
WDT BLOCK DIAGRAM
Enable WDT
WDT Counter
INTRC Source
÷128
Wake-up
from Power
Managed Modes
Change on IRCF bits
Programmable Postscaler
1:1 to 1:32,768
CLRWDT
Reset
WDT
Reset
All Device Resets
WDTPS<3:0>
4
Sleep
DS39636A-page 246
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
REGISTER 22-14: WDTCON: WATCHDOG TIMER CONTROL REGISTER
U-0
U-0
U-0
U-0
U-0
U-0
U-0
R/W-0
—
—
—
—
—
—
—
SWDTEN(1)
bit 7
bit 0
bit 7-1
Unimplemented: Read as ‘0’
bit 0
SWDTEN: Software Controlled Watchdog Timer Enable bit(1)
1 = Watchdog Timer is on
0 = Watchdog Timer is off
Note 1: This bit has no effect if the configuration bit WDTEN is enabled.
Legend:
TABLE 22-2:
Name
RCON
WDTCON
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
SUMMARY OF WATCHDOG TIMER REGISTERS
Bit 0
Reset
Values
on page
POR
BOR
48
—
SWDTEN(2)
50
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
IPEN
SBOREN(1)
—
RI
TO
PD
—
—
—
—
—
—
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used by the Watchdog Timer.
Note 1: The SBOREN bit is only available when the BOREN1:BOREN0 configuration bits = 01; otherwise, it is
disabled and reads as ‘0’. See Section 4.4 “Brown-out Reset (BOR)”.
2: This bit has no effect if the configuration bit WDTEN is enabled.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 247
PIC18F2X1X/4X1X
22.3
Two-Speed Start-up
In all other power managed modes, Two-Speed Startup is not used. The device will be clocked by the
currently selected clock source until the primary clock
source becomes available. The setting of the IESO bit
is ignored.
The Two-Speed Start-up feature helps to minimize the
latency period from oscillator start-up to code execution
by allowing the microcontroller to use the INTOSC
oscillator as a clock source until the primary clock
source is available. It is enabled by setting the IESO
configuration bit.
22.3.1
Two-Speed Start-up should be enabled only if the
primary oscillator mode is LP, XT, HS or HSPLL
(crystal-based modes). Other sources do not require
an OST start-up delay; for these, Two-Speed Start-up
should be disabled.
While using the INTOSC oscillator in Two-Speed Startup, the device still obeys the normal command
sequences for entering power managed modes,
including multiple SLEEP instructions (refer to
Section 3.1.4 “Multiple Sleep Commands”). In
practice, this means that user code can change the
SCS1:SCS0 bit settings or issue SLEEP instructions
before the OST times out. This would allow an
application to briefly wake-up, perform routine
“housekeeping” tasks and return to Sleep before the
device starts to operate from the primary oscillator.
When enabled, Resets and wake-ups from Sleep mode
cause the device to configure itself to run from the
internal oscillator block as the clock source, following
the time-out of the Power-up Timer after a Power-on
Reset is enabled. This allows almost immediate code
execution while the primary oscillator starts and the
OST is running. Once the OST times out, the device
automatically switches to PRI_RUN mode.
User code can also check if the primary clock source is
currently providing the device clocking by checking the
status of the OSTS bit (OSCCON<3>). If the bit is set,
the primary oscillator is providing the clock. Otherwise,
the internal oscillator block is providing the clock during
wake-up from Reset or Sleep mode.
To use a higher clock speed on wake-up, the INTOSC
or postscaler clock sources can be selected to provide
a higher clock speed by setting bits IRCF2:IRCF0
immediately after Reset. For wake-ups from Sleep, the
INTOSC or postscaler clock sources can be selected
by setting the IRCF2:IRCF0 bits prior to entering Sleep
mode.
FIGURE 22-2:
SPECIAL CONSIDERATIONS FOR
USING TWO-SPEED START-UP
TIMING TRANSITION FOR TWO-SPEED START-UP (INTOSC TO HSPLL)
Q1
Q3
Q2
Q4
Q2 Q3 Q4 Q1 Q2 Q3
Q1
INTOSC
Multiplexer
OSC1
TOST(1)
TPLL(1)
1
PLL Clock
Output
2
n-1 n
Clock
Transition(2)
CPU Clock
Peripheral
Clock
Program
Counter
PC
Wake from Interrupt Event
Note 1:
2:
DS39636A-page 248
PC + 2
PC + 6
PC + 4
OSTS bit Set
TOST = 1024 TOSC; TPLL = 2 ms (approx). These intervals are not shown to scale.
Clock transition typically occurs within 2-4 TOSC.
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
22.4
Fail-Safe Clock Monitor
The Fail-Safe Clock Monitor (FSCM) allows the
microcontroller to continue operation in the event of an
external oscillator failure by automatically switching the
device clock to the internal oscillator block. The FSCM
function is enabled by setting the FCMEN configuration
bit.
When FSCM is enabled, the INTRC oscillator runs at
all times to monitor clocks to peripherals and provide a
backup clock in the event of a clock failure. Clock
monitoring (shown in Figure 22-3) is accomplished by
creating a sample clock signal, which is the INTRC output divided by 64. This allows ample time between
FSCM sample clocks for a peripheral clock edge to
occur. The peripheral device clock and the sample
clock are presented as inputs to the Clock Monitor latch
(CM). The CM is set on the falling edge of the device
clock source, but cleared on the rising edge of the
sample clock.
FIGURE 22-3:
FSCM BLOCK DIAGRAM
Clock Monitor
Latch (CM)
(edge-triggered)
Peripheral
Clock
INTRC
Source
(32 µs)
÷ 64
S
Q
C
Q
To use a higher clock speed on wake-up, the INTOSC
or postscaler clock sources can be selected to provide
a higher clock speed by setting bits, IRCF2:IRCF0,
immediately after Reset. For wake-ups from Sleep, the
INTOSC or postscaler clock sources can be selected
by setting the IRCF2:IRCF0 bits prior to entering Sleep
mode.
The FSCM will detect failures of the primary or secondary clock sources only. If the internal oscillator block
fails, no failure would be detected, nor would any action
be possible.
22.4.1
Both the FSCM and the WDT are clocked by the
INTRC oscillator. Since the WDT operates with a
separate divider and counter, disabling the WDT has
no effect on the operation of the INTRC oscillator when
the FSCM is enabled.
As already noted, the clock source is switched to the
INTOSC clock when a clock failure is detected.
Depending on the frequency selected by the
IRCF2:IRCF0 bits, this may mean a substantial change
in the speed of code execution. If the WDT is enabled
with a small prescale value, a decrease in clock speed
allows a WDT time-out to occur and a subsequent
device Reset. For this reason, fail-safe clock events
also reset the WDT and postscaler, allowing it to start
timing from when execution speed was changed and
decreasing the likelihood of an erroneous time-out.
22.4.2
488 Hz
(2.048 ms)
Clock
Failure
Detected
Clock failure is tested for on the falling edge of the
sample clock. If a sample clock falling edge occurs
while CM is still set, a clock failure has been detected
(Figure 22-4). This causes the following:
• the FSCM generates an oscillator fail interrupt by
setting bit OSCFIF (PIR2<7>);
• the device clock source is switched to the internal
oscillator block (OSCCON is not updated to show
the current clock source – this is the fail-safe
condition); and
• the WDT is reset.
FSCM AND THE WATCHDOG TIMER
EXITING FAIL-SAFE OPERATION
The fail-safe condition is terminated by either a device
Reset or by entering a power managed mode. On
Reset, the controller starts the primary clock source
specified in Configuration Register 1H (with any
required start-up delays that are required for the oscillator mode, such as OST or PLL timer). The INTOSC
multiplexer provides the device clock until the primary
clock source becomes ready (similar to a Two-Speed
Start-up). The clock source is then switched to the primary clock (indicated by the OSTS bit in the OSCCON
register becoming set). The Fail-Safe Clock Monitor
then resumes monitoring the peripheral clock.
The primary clock source may never become ready
during start-up. In this case, operation is clocked by the
INTOSC multiplexer. The OSCCON register will remain
in its Reset state until a power managed mode is
entered.
During switchover, the postscaler frequency from the
internal oscillator block may not be sufficiently stable
for timing sensitive applications. In these cases, it may
be desirable to select another clock configuration and
enter an alternate power managed mode. This can be
done to attempt a partial recovery or execute a
controlled shutdown. See Section 3.1.4 “Multiple
Sleep Commands” and Section 22.3.1 “Special
Considerations for Using Two-Speed Start-up” for
more details.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 249
PIC18F2X1X/4X1X
FIGURE 22-4:
FSCM TIMING DIAGRAM
Sample Clock
Oscillator
Failure
Device
Clock
Output
CM Output
(Q)
Failure
Detected
OSCFIF
CM Test
Note:
22.4.3
CM Test
CM Test
The device clock is normally at a much higher frequency than the sample clock. The relative frequencies in this
example have been chosen for clarity.
22.4.4
FSCM INTERRUPTS IN POWER
MANAGED MODES
By entering a power managed mode, the clock
multiplexer selects the clock source selected by the
OSCCON register. Fail-Safe Monitoring of the power
managed clock source resumes in the power managed
mode.
If an oscillator failure occurs during power managed
operation, the subsequent events depend on whether
or not the oscillator failure interrupt is enabled. If
enabled (OSCFIF = 1), code execution will be clocked
by the INTOSC multiplexer. An automatic transition
back to the failed clock source will not occur.
If the interrupt is disabled, subsequent interrupts while
in Idle mode will cause the CPU to begin executing
instructions while being clocked by the INTOSC
source.
POR OR WAKE FROM SLEEP
The FSCM is designed to detect oscillator failure at any
point after the device has exited Power-on Reset
(POR) or low-power Sleep mode. When the primary
device clock is EC, RC or INTRC modes, monitoring
can begin immediately following these events.
For oscillator modes involving a crystal or resonator
(HS, HSPLL, LP or XT), the situation is somewhat
different. Since the oscillator may require a start-up
time considerably longer than the FCSM sample clock
time, a false clock failure may be detected. To prevent
this, the internal oscillator block is automatically configured as the device clock and functions until the primary
clock is stable (the OST and PLL timers have timed
out). This is identical to Two-Speed Start-up mode.
Once the primary clock is stable, the INTRC returns to
its role as the FSCM source.
Note:
The same logic that prevents false oscillator failure interrupts on POR or wake from
Sleep, will also prevent the detection of
the oscillator’s failure to start at all following these events. This can be avoided by
monitoring the OSTS bit and using a
timing routine to determine if the oscillator
is taking too long to start. Even so, no
oscillator failure interrupt will be flagged.
As noted in Section 22.3.1 “Special Considerations
for Using Two-Speed Start-up”, it is also possible to
select another clock configuration and enter an
alternate power managed mode while waiting for the
primary clock to become stable. When the new power
managed mode is selected, the primary clock is
disabled.
DS39636A-page 250
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
22.5
Program Verification and
Code Protection
The overall structure of the code protection on the
PIC18 Flash devices differs significantly from other
PICmicro® devices.
The user program memory is divided into five blocks.
One of these is a boot block of 2 Kbytes. The remainder
of the memory is divided into four blocks on binary
boundaries.
Each of the five blocks has three code protection bits
associated with them. They are:
FIGURE 22-5:
• Code-Protect bit (CPn)
• Write-Protect bit (WRTn)
• External Block Table Read bit (EBTRn)
Figure 22-5 shows the program memory organization
for 16- and 32-Kbyte devices and the specific code
protection bit associated with each block.
Figure 22-6 shows the program memory organization
for 48 and 64-Kbyte devices and the specific code
protection bit associated with each block. The actual
locations of the bits are summarized in Table 22-3.
CODE-PROTECTED PROGRAM MEMORY FOR PIC18F2410/2510/4410/4510
MEMORY SIZE/DEVICE
16 Kbytes
32 Kbytes
Address
(PIC18F2410/4410) (PIC18F2510/4510) Range
Boot Block
Boot Block
Block 0
Block 0
000000h
0007FFh
Block Code Protection
Controlled By:
CPB, WRTB, EBTRB
000800h
CP0, WRT0, EBTR0
001FFFh
002000h
Block 1
Block 1
CP1, WRT1, EBTR1
003FFFh
004000h
CP2, WRT2, EBTR2
Block 2
005FFFh
006000h
Block 3
CP3, WRT3, EBTR3
007FFFh
Unimplemented
Read ‘0’s
Unimplemented
Read ‘0’s
(Unimplemented Memory Space)
1FFFFFh
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 251
PIC18F2X1X/4X1X
FIGURE 22-6:
CODE-PROTECTED PROGRAM MEMORY FOR PIC18F2515/2610/4515/4610
MEMORY SIZE/DEVICE
48 Kbytes
64 Kbytes
(PIC18F2515/4515) (PIC18F2610/4610)
Boot Block
Boot Block
Block 0
Block 0
Address
Range
Block Code Protection
Controlled By:
000000h
0007FFh
CPB, WRTB, EBTRB
000800h
CP0, WRT0, EBTR0
003FFFh
004000h
Block 1
Block 1
CP1, WRT1, EBTR1
007FFFh
008000h
Block 2
Block 2
CP2, WRT2, EBTR2
00BFFFh
00C000h
Block 3
CP3, WRT3, EBTR3
00FFFFh
010000h
Unimplemented
Read ‘0’s
Unimplemented
Read ‘0’s
(Unimplemented Memory Space)
1FFFFFh
TABLE 22-3:
SUMMARY OF CODE PROTECTION REGISTERS
File Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
CP2(1)
CP1
CP0
300008h
CONFIG5L
—
—
—
—
CP3(1,2)
300009h
CONFIG5H
—
CPB
—
—
—
—
—
—
30000Ah
CONFIG6L
—
—
—
—
WRT3(1,2)
WRT2(1)
WRT1
WRT0
30000Bh
CONFIG6H
—
WRTB
WRTC
—
—
—
—
—
EBTR1
EBTR0
—
—
30000Ch
CONFIG7L
—
—
—
—
EBTR3
30000Dh
CONFIG7H
—
EBTRB
—
—
—
Legend:
Note 1:
2:
(1,2)
EBTR2
—
(1)
Shaded cells are unimplemented.
Unimplemented in PIC18F2410/4410 devices; maintain this bit set.
Unimplemented in PIC18F2515/4515 devices; maintain this bit set.
DS39636A-page 252
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
22.5.1
PROGRAM MEMORY
CODE PROTECTION
The program memory may be read to or written from
any location using the table read and table write
instructions. The device ID may be read with table
reads. The configuration registers may be read and
written with the table read and table write instructions.
from a location outside of that block is not allowed to
read and will result in reading ‘0’s. Figures 22-7
through 22-10 illustrate table write and table read
protection.
Note:
In normal execution mode, the CPn bits have no direct
effect. CPn bits inhibit external reads and writes. The
EBTRn bits control table reads. For a block of user
memory with the EBTRn bit set to ‘0’, a table read
instruction that executes from within that block is
allowed to read. A table read instruction that executes
FIGURE 22-7:
Code protection bits may only be written to
a ‘0’ from a ‘1’ state. It is not possible to
write a ‘1’ to a bit in the ‘0’ state. Code
protection bits are only set to ‘1’ by a full
chip erase or block erase function. The full
chip erase and block erase functions can
only be initiated via ICSP or an external
programmer.
EXTERNAL BLOCK TABLE READ (EBTRn) DISALLOWED
(16-KBYTE AND 32-KBYTE DEVICES)
Register Values
Program Memory
Configuration Bit Settings
000000h
0007FFh
000800h
WRTB, EBTRB = 11
TBLPTR = 0008FFh
WRT0, EBTR0 = 10
001FFFh
002000h
PC = 003FFEh
TBLRD*
WRT1, EBTR1 = 11
003FFFh
004000h
WRT2, EBTR2 = 11
005FFFh
006000h
WRT3, EBTR3 = 11
007FFFh
Results: All table reads from external blocks to Blockn are disabled whenever EBTRn = 0.
TABLAT register returns a value of ‘0’.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 253
PIC18F2X1X/4X1X
FIGURE 22-8:
EXTERNAL BLOCK TABLE READ (EBTRn) ALLOWED
(16-KBYTE AND 32-KBYTE DEVICES)
Register Values
Program Memory
Configuration Bit Settings
000000h
WRTB, EBTRB = 11
0007FFh
000800h
TBLPTR = 0008FFh
PC = 001FFEh
WRT0, EBTR0 = 10
TBLRD*
001FFFh
002000h
WRT1, EBTR1 = 11
003FFFh
004000h
WRT2, EBTR2 = 11
005FFFh
006000h
WRT3, EBTR3 = 11
007FFFh
Results: Table reads permitted within Blockn, even when EBTRBn = 0.
TABLAT register returns the value of the data at the location TBLPTR.
FIGURE 22-9:
EXTERNAL BLOCK TABLE READ (EBTRn) DISALLOWED
(48-KBYTE AND 64-KBYTE DEVICES)
Register Values
Program Memory
Configuration Bit Settings
000000h
0007FFh
000800h
WRTB, EBTRB = 11
TBLPTR = 0008FFh
WRT0, EBTR0 = 10
003FFFh
004000h
PC = 003FFEh
TBLRD*
WRT1, EBTR1 = 11
007FFFh
008000h
WRT2, EBTR2 = 11
00BFFFh
00C000h
WRT3, EBTR3 = 11
00FFFFh
Results: All table reads from external blocks to Blockn are disabled whenever EBTRn = 0.
TABLAT register returns a value of ‘0’.
DS39636A-page 254
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
FIGURE 22-10:
EXTERNAL BLOCK TABLE READ (EBTRn) ALLOWED
(48-KBYTE AND 64-KBYTE DEVICES)
Register Values
Program Memory
Configuration Bit Settings
000000h
WRTB, EBTRB = 11
0007FFh
000800h
TBLPTR = 0008FFh
PC = 001FFEh
WRT0, EBTR0 = 10
TBLRD*
003FFFh
004000h
WRT1, EBTR1 = 11
007FFFh
008000h
WRT2, EBTR2 = 11
00BFFFh
00C000h
WRT3, EBTR3 = 11
00FFFFh
Results: Table reads permitted within Blockn, even when EBTRBn = 0.
TABLAT register returns the value of the data at the location TBLPTR.
22.5.2
CONFIGURATION REGISTER
PROTECTION
22.8
The configuration registers can be write-protected. The
WRTC bit controls protection of the configuration
registers. In normal execution mode, the WRTC bit is
readable only. WRTC can only be written via ICSP or
an external programmer.
22.6
When the DEBUG configuration bit is programmed to a
‘0’, the In-Circuit Debugger functionality is enabled.
This function allows simple debugging functions when
used with MPLAB® IDE. When the microcontroller has
this feature enabled, some resources are not available
for general use. Table 22-4 shows which resources are
required by the background debugger.
ID Locations
Eight memory locations (200000h-200007h) are
designated as ID locations, where the user can store
checksum or other code identification numbers. These
locations are both readable and writable during normal
execution through the TBLRD instruction; during
program/verify these locations are readable and
writable. The ID locations can be read when the device
is code-protected.
22.7
In-Circuit Debugger
In-Circuit Serial Programming
PIC18F2X1X/4X1X microcontrollers can be serially
programmed while in the end application circuit. This is
simply done with two lines for clock and data and three
other lines for power, ground and the programming
voltage. This allows customers to manufacture boards
with unprogrammed devices and then program the
microcontroller just before shipping the product. This
also allows the most recent firmware or a custom
firmware to be programmed.
 2004 Microchip Technology Inc.
TABLE 22-4:
DEBUGGER RESOURCES
I/O pins:
RB6, RB7
Stack:
2 levels
Program Memory:
512 bytes
Data Memory:
10 bytes
To use the In-Circuit Debugger function of the microcontroller, the design must implement In-Circuit Serial
Programming connections to MCLR/VPP/RE3, VDD,
VSS, RB7 and RB6. This will interface to the In-Circuit
Debugger module available from Microchip or one of
the third party development tool companies.
Preliminary
DS39636A-page 255
PIC18F2X1X/4X1X
22.9
Single-Supply ICSP Programming
The LVP configuration bit enables Single-Supply ICSP
Programming (formerly known as Low-Voltage ICSP
Programming or LVP). When Single-Supply Programming is enabled, the microcontroller can be programmed
without requiring high voltage being applied to the
MCLR/VPP/RE3 pin, but the RB5/KBI1/PGM pin is then
dedicated to controlling Program mode entry and is not
available as a general purpose I/O pin.
While programming, using Single-Supply Programming mode, VDD is applied to the MCLR/VPP/RE3 pin
as in normal execution mode. To enter Programming
mode, VDD is applied to the PGM pin.
If Single-Supply ICSP Programming mode will not be
used, the LVP bit can be cleared. RB5/KBI1/PGM then
becomes available as the digital I/O pin, RB5. The LVP
bit may be set or cleared only when using standard
high-voltage programming (VIHH applied to the MCLR/
VPP/RE3 pin). Once LVP has been disabled, only the
standard high-voltage programming is available and
must be used to program the device.
Memory that is not code-protected can be erased using
either a block erase, or erased row by row, then written
at any specified VDD. If code-protected memory is to be
erased, a block erase is required. If a block erase is to
be performed when using Low-Voltage Programming,
the device must be supplied with VDD of 4.5V to 5.5V.
Note 1: High-voltage programming is always
available, regardless of the state of the
LVP bit or the PGM pin, by applying VIHH
to the MCLR pin.
2: By default, Single-Supply ICSP is
enabled in unprogrammed devices (as
supplied from Microchip) and erased
devices.
3: When Single-Supply Programming is
enabled, the RB5 pin can no longer be
used as a general purpose I/O pin.
4: When LVP is enabled, externally pull the
PGM pin to VSS to allow normal program
execution.
DS39636A-page 256
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
23.0
INSTRUCTION SET SUMMARY
PIC18F2X1X/4X1X devices incorporate the standard
set of 75 PIC18 core instructions, as well as an
extended set of 8 new instructions for the optimization
of code that is recursive or that utilizes a software
stack. The extended set is discussed later in this
section.
23.1
Standard Instruction Set
The standard PIC18 instruction set adds many
enhancements to the previous PICmicro® instruction
sets, while maintaining an easy migration from these
PICmicro instruction sets. Most instructions are a
single program memory word (16 bits), but there are
four instructions that require two program memory
locations.
Each single-word instruction is a 16-bit word divided
into an opcode, which specifies the instruction type and
one or more operands, which further specify the
operation of the instruction.
The instruction set is highly orthogonal and is grouped
into four basic categories:
•
•
•
•
Byte-oriented operations
Bit-oriented operations
Literal operations
Control operations
The PIC18 instruction set summary in Table 23-2 lists
byte-oriented, bit-oriented, literal and control
operations. Table 23-1 shows the opcode field
descriptions.
Most byte-oriented instructions have three operands:
1.
2.
3.
The file register (specified by ‘f’)
The destination of the result (specified by ‘d’)
The accessed memory (specified by ‘a’)
The file register designator ‘f’ specifies which file register is to be used by the instruction. The destination
designator ‘d’ specifies where the result of the operation is to be placed. If ‘d’ is zero, the result is placed in
the WREG register. If ‘d’ is one, the result is placed in
the file register specified in the instruction.
All bit-oriented instructions have three operands:
1.
2.
3.
The file register (specified by ‘f’)
The bit in the file register (specified by ‘b’)
The accessed memory (specified by ‘a’)
The literal instructions may use some of the following
operands:
• A literal value to be loaded into a file register
(specified by ‘k’)
• The desired FSR register to load the literal value
into (specified by ‘f’)
• No operand required
(specified by ‘—’)
The control instructions may use some of the following
operands:
• A program memory address (specified by ‘n’)
• The mode of the CALL or RETURN instructions
(specified by ‘s’)
• The mode of the table read and table write
instructions (specified by ‘m’)
• No operand required
(specified by ‘—’)
All instructions are a single word, except for four
double-word instructions. These instructions were
made double-word to contain the required information
in 32 bits. In the second word, the 4 MSbs are ‘1’s. If
this second word is executed as an instruction (by
itself), it will execute as a NOP.
All single-word instructions are executed in a single
instruction cycle, unless a conditional test is true or the
program counter is changed as a result of the instruction. In these cases, the execution takes two instruction
cycles, with the additional instruction cycle(s) executed
as a NOP.
The double-word instructions execute in two instruction
cycles.
One instruction cycle consists of four oscillator periods.
Thus, for an oscillator frequency of 4 MHz, the normal
instruction execution time is 1 µs. If a conditional test is
true, or the program counter is changed as a result of
an instruction, the instruction execution time is 2 µs.
Two-word branch instructions (if true) would take 3 µs.
Figure 23-1 shows the general formats that the instructions can have. All examples use the convention ‘nnh’
to represent a hexadecimal number.
The Instruction Set Summary, shown in Table 23-2,
lists the standard instructions recognized by the
Microchip MPASM™ Assembler.
Section 23.1.1 “Standard Instruction Set” provides
a description of each instruction.
The bit field designator ‘b’ selects the number of the bit
affected by the operation, while the file register designator ‘f’ represents the number of the file in which the
bit is located.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 257
PIC18F2X1X/4X1X
TABLE 23-1:
OPCODE FIELD DESCRIPTIONS
Field
Description
a
RAM access bit
a = 0: RAM location in Access RAM (BSR register is ignored)
a = 1: RAM bank is specified by BSR register
bbb
Bit address within an 8-bit file register (0 to 7).
BSR
Bank Select Register. Used to select the current RAM bank.
C, DC, Z, OV, N
ALU status bits: Carry, Digit Carry, Zero, Overflow, Negative.
d
Destination select bit
d = 0: store result in WREG
d = 1: store result in file register f
dest
Destination: either the WREG register or the specified register file location.
f
8-bit Register file address (00h to FFh) or 2-bit FSR designator (0h to 3h).
fs
12-bit Register file address (000h to FFFh). This is the source address.
fd
12-bit Register file address (000h to FFFh). This is the destination address.
GIE
Global Interrupt Enable bit.
k
Literal field, constant data or label (may be either an 8-bit, 12-bit or a 20-bit value).
label
Label name.
mm
The mode of the TBLPTR register for the table read and table write instructions.
Only used with table read and table write instructions:
*
No change to register (such as TBLPTR with table reads and writes)
*+
Post-Increment register (such as TBLPTR with table reads and writes)
*-
Post-Decrement register (such as TBLPTR with table reads and writes)
Pre-Increment register (such as TBLPTR with table reads and writes)
+*
n
The relative address (2’s complement number) for relative branch instructions or the direct address for
call/branch and return instructions.
PC
Program Counter.
PCL
Program Counter Low Byte.
PCH
Program Counter High Byte.
PCLATH
Program Counter High Byte Latch.
PCLATU
Program Counter Upper Byte Latch.
PD
Power-down bit.
PRODH
Product of Multiply High Byte.
PRODL
Product of Multiply Low Byte.
s
Fast Call/Return mode select bit
s = 0: do not update into/from shadow registers
s = 1: certain registers loaded into/from shadow registers (Fast mode)
TBLPTR
21-bit Table Pointer (points to a Program Memory location).
TABLAT
8-bit Table Latch.
TO
Time-out bit.
TOS
Top-of-Stack.
u
Unused or unchanged.
WDT
Watchdog Timer.
WREG
Working register (accumulator).
x
Don’t care (‘0’ or ‘1’). The assembler will generate code with x = 0. It is the recommended form of use for
compatibility with all Microchip software tools.
zs
7-bit offset value for indirect addressing of register files (source).
7-bit offset value for indirect addressing of register files (destination).
zd
{
}
Optional argument.
[text]
Indicates an indexed address.
(text)
The contents of text.
[expr]<n>
Specifies bit n of the register indicated by the pointer expr.
→
Assigned to.
< >
Register bit field.
∈
In the set of.
italics
User defined term (font is Courier).
DS39636A-page 258
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
FIGURE 23-1:
GENERAL FORMAT FOR INSTRUCTIONS
Byte-oriented file register operations
15
10
9 8 7
OPCODE d
a
Example Instruction
0
f (FILE #)
ADDWF MYREG, W, B
d = 0 for result destination to be WREG register
d = 1 for result destination to be file register (f)
a = 0 to force Access Bank
a = 1 for BSR to select bank
f = 8-bit file register address
Byte to Byte move operations (2-word)
15
12 11
OPCODE
15
0
f (Source FILE #)
12 11
MOVFF MYREG1, MYREG2
0
f (Destination FILE #)
1111
f = 12-bit file register address
Bit-oriented file register operations
15
12 11
9 8 7
OPCODE b (BIT #) a
0
f (FILE #)
BSF MYREG, bit, B
b = 3-bit position of bit in file register (f)
a = 0 to force Access Bank
a = 1 for BSR to select bank
f = 8-bit file register address
Literal operations
15
8
7
OPCODE
0
k (literal)
MOVLW
7Fh
k = 8-bit immediate value
Control operations
CALL, GOTO and Branch operations
15
8 7
OPCODE
15
0
n<7:0> (literal)
12 11
GOTO Label
0
n<19:8> (literal)
1111
n = 20-bit immediate value
15
8 7
OPCODE
15
S
0
CALL MYFUNC
n<7:0> (literal)
12 11
0
n<19:8> (literal)
1111
S = Fast bit
15
OPCODE
15
OPCODE
 2004 Microchip Technology Inc.
11 10
0
BRA MYFUNC
n<10:0> (literal)
8 7
0
n<7:0> (literal)
Preliminary
BC MYFUNC
DS39636A-page 259
PIC18F2X1X/4X1X
TABLE 23-2:
PIC18FXXXX INSTRUCTION SET
Mnemonic,
Operands
16-Bit Instruction Word
Description
Cycles
MSb
LSb
Status
Affected
Notes
BYTE-ORIENTED OPERATIONS
ADDWF
ADDWFC
ANDWF
CLRF
COMF
CPFSEQ
CPFSGT
CPFSLT
DECF
DECFSZ
DCFSNZ
INCF
INCFSZ
INFSNZ
IORWF
MOVF
MOVFF
f, d, a
f, d, a
f, d, a
f, a
f, d, a
f, a
f, a
f, a
f, d, a
f, d, a
f, d, a
f, d, a
f, d, a
f, d, a
f, d, a
f, d, a
fs, fd
MOVWF
MULWF
NEGF
RLCF
RLNCF
RRCF
RRNCF
SETF
SUBFWB
f, a
f, a
f, a
f, d, a
f, d, a
f, d, a
f, d, a
f, a
f, d, a
SUBWF
SUBWFB
f, d, a
f, d, a
SWAPF
TSTFSZ
XORWF
f, d, a
f, a
f, d, a
Note 1:
2:
3:
4:
Add WREG and f
Add WREG and Carry bit to f
AND WREG with f
Clear f
Complement f
Compare f with WREG, skip =
Compare f with WREG, skip >
Compare f with WREG, skip <
Decrement f
Decrement f, Skip if 0
Decrement f, Skip if Not 0
Increment f
Increment f, Skip if 0
Increment f, Skip if Not 0
Inclusive OR WREG with f
Move f
Move fs (source) to 1st word
fd (destination) 2nd word
Move WREG to f
Multiply WREG with f
Negate f
Rotate Left f through Carry
Rotate Left f (No Carry)
Rotate Right f through Carry
Rotate Right f (No Carry)
Set f
Subtract f from WREG with
borrow
Subtract WREG from f
Subtract WREG from f with
borrow
Swap nibbles in f
Test f, skip if 0
Exclusive OR WREG with f
1
1
1
1
1
1 (2 or 3)
1 (2 or 3)
1 (2 or 3)
1
1 (2 or 3)
1 (2 or 3)
1
1 (2 or 3)
1 (2 or 3)
1
1
2
C, DC, Z, OV, N
C, DC, Z, OV, N
Z, N
Z
Z, N
None
None
None
C, DC, Z, OV, N
None
None
C, DC, Z, OV, N
None
None
Z, N
Z, N
None
1, 2
1, 2
1,2
2
1, 2
4
4
1, 2
1, 2, 3, 4
1, 2, 3, 4
1, 2
1, 2, 3, 4
4
1, 2
1, 2
1
1
1
1
1
1
1
1
1
1
0010
0010
0001
0110
0001
0110
0110
0110
0000
0010
0100
0010
0011
0100
0001
0101
1100
1111
0110
0000
0110
0011
0100
0011
0100
0110
0101
01da
00da
01da
101a
11da
001a
010a
000a
01da
11da
11da
10da
11da
10da
00da
00da
ffff
ffff
111a
001a
110a
01da
01da
00da
00da
100a
01da
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
1
1
0101 11da
0101 10da
ffff
ffff
ffff C, DC, Z, OV, N 1, 2
ffff C, DC, Z, OV, N
1
0011 10da
1 (2 or 3) 0110 011a
1
0001 10da
ffff
ffff
ffff
ffff None
ffff None
ffff Z, N
None
None
1, 2
C, DC, Z, OV, N
C, Z, N
1, 2
Z, N
C, Z, N
Z, N
None
1, 2
C, DC, Z, OV, N
4
1, 2
When a Port register is modified as a function of itself (e.g., MOVF PORTB, 1, 0), the value used will be that
value present on the pins themselves. For example, if the data latch is ‘1’ for a pin configured as input and is
driven low by an external device, the data will be written back with a ‘0’.
If this instruction is executed on the TMR0 register (and where applicable, ‘d’ = 1), the prescaler will be cleared
if assigned.
If Program Counter (PC) is modified or a conditional test is true, the instruction requires two cycles. The second
cycle is executed as a NOP.
Some instructions are two-word instructions. The second word of these instructions will be executed as a NOP
unless the first word of the instruction retrieves the information embedded in these 16 bits. This ensures that all
program memory locations have a valid instruction.
DS39636A-page 260
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
TABLE 23-2:
PIC18FXXXX INSTRUCTION SET (CONTINUED)
16-Bit Instruction Word
Mnemonic,
Operands
Description
Cycles
MSb
LSb
Status
Affected
Notes
BIT-ORIENTED OPERATIONS
BCF
BSF
BTFSC
BTFSS
BTG
f, b, a
f, b, a
f, b, a
f, b, a
f, d, a
Bit Clear f
Bit Set f
Bit Test f, Skip if Clear
Bit Test f, Skip if Set
Bit Toggle f
1
1
1 (2 or 3)
1 (2 or 3)
1
1001
1000
1011
1010
0111
bbba
bbba
bbba
bbba
bbba
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
None
None
None
None
None
1 (2)
1 (2)
1 (2)
1 (2)
1 (2)
1 (2)
1 (2)
2
1 (2)
2
0010
0110
0011
0111
0101
0001
0100
0nnn
0000
110s
kkkk
0000
0000
1111
kkkk
0000
xxxx
0000
0000
1nnn
0000
0000
nnnn
nnnn
nnnn
nnnn
nnnn
nnnn
nnnn
nnnn
nnnn
kkkk
kkkk
0000
0000
kkkk
kkkk
0000
xxxx
0000
0000
nnnn
1111
0001
nnnn
nnnn
nnnn
nnnn
nnnn
nnnn
nnnn
nnnn
nnnn
kkkk
kkkk
0100
0111
kkkk
kkkk
0000
xxxx
0110
0101
nnnn
1111
000s
None
None
None
None
None
None
None
None
None
None
1
1
1
1
2
1
2
1110
1110
1110
1110
1110
1110
1110
1101
1110
1110
1111
0000
0000
1110
1111
0000
1111
0000
0000
1101
0000
0000
2
2
1
0000 1100
0000 0000
0000 0000
kkkk
0001
0000
1, 2
1, 2
3, 4
3, 4
1, 2
CONTROL OPERATIONS
BC
BN
BNC
BNN
BNOV
BNZ
BOV
BRA
BZ
CALL
n
n
n
n
n
n
n
n
n
n, s
CLRWDT
DAW
GOTO
—
—
n
NOP
NOP
POP
PUSH
RCALL
RESET
RETFIE
—
—
—
—
n
s
Branch if Carry
Branch if Negative
Branch if Not Carry
Branch if Not Negative
Branch if Not Overflow
Branch if Not Zero
Branch if Overflow
Branch Unconditionally
Branch if Zero
Call subroutine 1st word
2nd word
Clear Watchdog Timer
Decimal Adjust WREG
Go to address 1st word
2nd word
No Operation
No Operation
Pop top of return stack (TOS)
Push top of return stack (TOS)
Relative Call
Software device Reset
Return from interrupt enable
RETLW
RETURN
SLEEP
k
s
—
Return with literal in WREG
Return from Subroutine
Go into Standby mode
Note 1:
2:
3:
4:
1
1
2
TO, PD
C
None
None
None
None
None
None
All
GIE/GIEH,
PEIE/GIEL
kkkk None
001s None
0011 TO, PD
4
When a Port register is modified as a function of itself (e.g., MOVF PORTB, 1, 0), the value used will be that
value present on the pins themselves. For example, if the data latch is ‘1’ for a pin configured as input and is
driven low by an external device, the data will be written back with a ‘0’.
If this instruction is executed on the TMR0 register (and where applicable, ‘d’ = 1), the prescaler will be cleared
if assigned.
If Program Counter (PC) is modified or a conditional test is true, the instruction requires two cycles. The second
cycle is executed as a NOP.
Some instructions are two-word instructions. The second word of these instructions will be executed as a NOP
unless the first word of the instruction retrieves the information embedded in these 16 bits. This ensures that all
program memory locations have a valid instruction.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 261
PIC18F2X1X/4X1X
TABLE 23-2:
PIC18FXXXX INSTRUCTION SET (CONTINUED)
16-Bit Instruction Word
Mnemonic,
Operands
Description
Cycles
MSb
LSb
Status
Affected
Notes
LITERAL OPERATIONS
ADDLW
ANDLW
IORLW
LFSR
k
k
k
f, k
MOVLB
MOVLW
MULLW
RETLW
SUBLW
XORLW
k
k
k
k
k
k
Add literal and WREG
AND literal with WREG
Inclusive OR literal with WREG
Move literal (12-bit) 2nd word
to FSR(f)
1st word
Move literal to BSR<3:0>
Move literal to WREG
Multiply literal with WREG
Return with literal in WREG
Subtract WREG from literal
Exclusive OR literal with WREG
1
1
1
2
1
1
1
2
1
1
0000
0000
0000
1110
1111
0000
0000
0000
0000
0000
0000
1111
1011
1001
1110
0000
0001
1110
1101
1100
1000
1010
kkkk
kkkk
kkkk
00ff
kkkk
0000
kkkk
kkkk
kkkk
kkkk
kkkk
kkkk
kkkk
kkkk
kkkk
kkkk
kkkk
kkkk
kkkk
kkkk
kkkk
kkkk
C, DC, Z, OV, N
Z, N
Z, N
None
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
1000
1001
1010
1011
1100
1101
1110
1111
None
None
None
None
None
None
None
None
None
None
None
None
C, DC, Z, OV, N
Z, N
DATA MEMORY ↔ PROGRAM MEMORY OPERATIONS
TBLRD*
TBLRD*+
TBLRD*TBLRD+*
TBLWT*
TBLWT*+
TBLWT*TBLWT+*
Note 1:
2:
3:
4:
Table Read
2
Table Read with post-increment
Table Read with post-decrement
Table Read with pre-increment
Table Write
2
Table Write with post-increment
Table Write with post-decrement
Table Write with pre-increment
When a Port register is modified as a function of itself (e.g., MOVF PORTB, 1, 0), the value used will be that
value present on the pins themselves. For example, if the data latch is ‘1’ for a pin configured as input and is
driven low by an external device, the data will be written back with a ‘0’.
If this instruction is executed on the TMR0 register (and where applicable, ‘d’ = 1), the prescaler will be cleared
if assigned.
If Program Counter (PC) is modified or a conditional test is true, the instruction requires two cycles. The second
cycle is executed as a NOP.
Some instructions are two-word instructions. The second word of these instructions will be executed as a NOP
unless the first word of the instruction retrieves the information embedded in these 16 bits. This ensures that all
program memory locations have a valid instruction.
DS39636A-page 262
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
23.1.1
STANDARD INSTRUCTION SET
ADDLW
ADD Literal to W
ADDWF
ADD W to f
Syntax:
ADDLW
Syntax:
ADDWF
Operands:
0 ≤ f ≤ 255
d ∈ [0,1]
a ∈ [0,1]
Operation:
(W) + (f) → dest
Status Affected:
N, OV, C, DC, Z
k
Operands:
0 ≤ k ≤ 255
Operation:
(W) + k → W
Status Affected:
N, OV, C, DC, Z
Encoding:
0000
1111
kkkk
kkkk
Description:
The contents of W are added to the
8-bit literal ‘k’ and the result is placed in
W.
Words:
1
Cycles:
1
Encoding:
0010
Q1
Q2
Q3
Q4
Read
literal ‘k’
Process
Data
Write to W
Example:
ADDLW
=
25h
ffff
Words:
1
Cycles:
1
Before Instruction
W
ffff
Add W to register ‘f’. If ‘d’ is ‘0’, the
result is stored in W. If ‘d’ is ‘1’, the
result is stored back in register ‘f’
(default).
If ‘a’ is ‘0’, the Access Bank is selected.
If ‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates
in Indexed Literal Offset Addressing
mode whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
15h
W
= 10h
After Instruction
01da
Description:
Q Cycle Activity:
Decode
f {,d {,a}}
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
register ‘f’
Process
Data
Write to
destination
Example:
ADDWF
REG, 0, 0
Before Instruction
W
=
REG
=
After Instruction
W
REG
Note:
=
=
17h
0C2h
0D9h
0C2h
All PIC18 instructions may take an optional label argument preceding the instruction mnemonic for use in
symbolic addressing. If a label is used, the instruction format then becomes: {label} instruction argument(s).
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 263
PIC18F2X1X/4X1X
ADDWFC
ADD W and Carry bit to f
ANDLW
AND Literal with W
Syntax:
ADDWFC
Syntax:
ANDLW
Operands:
0 ≤ f ≤ 255
d ∈ [0,1]
a ∈ [0,1]
f {,d {,a}}
(W) + (f) + (C) → dest
Operation:
Status Affected:
Encoding:
0010
Description:
00da
ffff
ffff
Add W, the Carry flag and data memory
location ‘f’. If ‘d’ is ‘0’, the result is
placed in W. If ‘d’ is ‘1’, the result is
placed in data memory location ‘f’.
If ‘a’ is ‘0’, the Access Bank is selected.
If ‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates
in Indexed Literal Offset Addressing
mode whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
Words:
1
Cycles:
1
Operands:
0 ≤ k ≤ 255
Operation:
(W) .AND. k → W
Status Affected:
N, Z
Encoding:
N,OV, C, DC, Z
k
0000
1011
kkkk
kkkk
Description:
The contents of W are AND’ed with the
8-bit literal ‘k’. The result is placed in W.
Words:
1
Cycles:
1
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read literal
‘k’
Process
Data
Write to W
Example:
ANDLW
05Fh
Before Instruction
W
=
After Instruction
W
=
A3h
03h
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
register ‘f’
Process
Data
Write to
destination
Example:
ADDWFC
Before Instruction
Carry bit =
REG
=
W
=
After Instruction
Carry bit =
REG
=
W
=
DS39636A-page 264
REG, 0, 1
1
02h
4Dh
0
02h
50h
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
ANDWF
AND W with f
BC
Branch if Carry
Syntax:
ANDWF
Syntax:
BC
Operands:
0 ≤ f ≤ 255
d ∈ [0,1]
a ∈ [0,1]
Operands:
-128 ≤ n ≤ 127
Operation:
if Carry bit is ‘1’
(PC) + 2 + 2n → PC
None
f {,d {,a}}
Operation:
(W) .AND. (f) → dest
Status Affected:
Status Affected:
N, Z
Encoding:
Encoding:
0001
Description:
01da
ffff
ffff
The contents of W are AND’ed with
register ‘f’. If ‘d’ is ‘0’, the result is stored
in W. If ‘d’ is ‘1’, the result is stored back
in register ‘f’ (default).
If ‘a’ is ‘0’, the Access Bank is selected.
If ‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates
in Indexed Literal Offset Addressing
mode whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
Words:
1
Cycles:
1
Q2
Q3
Q4
Decode
Read
register ‘f’
Process
Data
Write to
destination
REG, 0, 0
W
REG
=
=
1
Cycles:
1(2)
nnnn
Q Cycle Activity:
If Jump:
Q1
Q2
Q3
Q4
Decode
Read literal
‘n’
Process
Data
Write to PC
No
operation
No
operation
No
operation
No
operation
Q1
Q2
Q3
Q4
Decode
Read literal
‘n’
Process
Data
No
operation
Example:
HERE
Before Instruction
PC
After Instruction
If Carry
PC
If Carry
PC
17h
C2h
02h
C2h
 2004 Microchip Technology Inc.
nnnn
If the Carry bit is ‘1’, then the program
will branch.
The 2’s complement number ‘2n’ is
added to the PC. Since the PC will have
incremented to fetch the next
instruction, the new address will be
PC + 2 + 2n. This instruction is then a
two-cycle instruction.
Words:
Before Instruction
W
=
REG
=
After Instruction
0010
If No Jump:
Q1
ANDWF
1110
Description:
Q Cycle Activity:
Example:
n
Preliminary
BC
5
=
address (HERE)
=
=
=
=
1;
address (HERE + 12)
0;
address (HERE + 2)
DS39636A-page 265
PIC18F2X1X/4X1X
BCF
Bit Clear f
BN
Branch if Negative
Syntax:
BCF
Syntax:
BN
Operands:
0 ≤ f ≤ 255
0≤b≤7
a ∈ [0,1]
Operands:
-128 ≤ n ≤ 127
Operation:
if Negative bit is ‘1’
(PC) + 2 + 2n → PC
None
f, b {,a}
Operation:
0 → f<b>
Status Affected:
Status Affected:
None
Encoding:
Encoding:
1001
Description:
bbba
ffff
ffff
Bit ‘b’ in register ‘f’ is cleared.
If ‘a’ is ‘0’, the Access Bank is selected.
If ‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates
in Indexed Literal Offset Addressing
mode whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
Words:
1
Cycles:
1
Q1
Q2
Q3
Q4
Read
register ‘f’
Process
Data
Write
register ‘f’
Example:
BCF
Before Instruction
FLAG_REG =
After Instruction
FLAG_REG =
DS39636A-page 266
FLAG_REG,
1110
Description:
0110
nnnn
nnnn
If the Negative bit is ‘1’, then the
program will branch.
The 2’s complement number ‘2n’ is
added to the PC. Since the PC will have
incremented to fetch the next
instruction, the new address will be
PC + 2 + 2n. This instruction is then a
two-cycle instruction.
Words:
1
Cycles:
1(2)
Q Cycle Activity:
If Jump:
Q Cycle Activity:
Decode
n
Q1
Q2
Q3
Q4
Decode
Read literal
‘n’
Process
Data
Write to PC
No
operation
No
operation
No
operation
No
operation
If No Jump:
7, 0
Q1
Q2
Q3
Q4
Decode
Read literal
‘n’
Process
Data
No
operation
C7h
47h
Example:
HERE
Before Instruction
PC
After Instruction
If Negative
PC
If Negative
PC
Preliminary
BN
Jump
=
address (HERE)
=
=
=
=
1;
address (Jump)
0;
address (HERE + 2)
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
BNC
Branch if Not Carry
BNN
Branch if Not Negative
Syntax:
BNC
Syntax:
BNN
n
n
Operands:
-128 ≤ n ≤ 127
Operands:
-128 ≤ n ≤ 127
Operation:
if Carry bit is ‘0’
(PC) + 2 + 2n → PC
Operation:
if Negative bit is ‘0’
(PC) + 2 + 2n → PC
Status Affected:
None
Status Affected:
None
Encoding:
1110
0011
nnnn
nnnn
Encoding:
1110
0111
nnnn
nnnn
Description:
If the Carry bit is ‘0’, then the program
will branch.
The 2’s complement number ‘2n’ is
added to the PC. Since the PC will have
incremented to fetch the next
instruction, the new address will be
PC + 2 + 2n. This instruction is then a
two-cycle instruction.
Description:
If the Negative bit is ‘0’, then the
program will branch.
The 2’s complement number ‘2n’ is
added to the PC. Since the PC will have
incremented to fetch the next
instruction, the new address will be
PC + 2 + 2n. This instruction is then a
two-cycle instruction.
Words:
1
Words:
1
Cycles:
1(2)
Cycles:
1(2)
Q Cycle Activity:
If Jump:
Q Cycle Activity:
If Jump:
Q1
Q2
Q3
Q4
Q1
Q2
Q3
Q4
Decode
Read literal
‘n’
Process
Data
Write to PC
Decode
Read literal
‘n’
Process
Data
Write to PC
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
Q1
Q2
Q3
Q4
Q1
Q2
Q3
Q4
Decode
Read literal
‘n’
Process
Data
No
operation
Decode
Read literal
‘n’
Process
Data
No
operation
If No Jump:
Example:
If No Jump:
HERE
Before Instruction
PC
After Instruction
If Carry
PC
If Carry
PC
BNC
Jump
=
address (HERE)
=
=
=
=
0;
address (Jump)
1;
address (HERE + 2)
 2004 Microchip Technology Inc.
Example:
HERE
Before Instruction
PC
After Instruction
If Negative
PC
If Negative
PC
Preliminary
BNN
Jump
=
address (HERE)
=
=
=
=
0;
address (Jump)
1;
address (HERE + 2)
DS39636A-page 267
PIC18F2X1X/4X1X
BNOV
Branch if Not Overflow
BNZ
Branch if Not Zero
Syntax:
BNOV
Syntax:
BNZ
n
n
Operands:
-128 ≤ n ≤ 127
Operands:
-128 ≤ n ≤ 127
Operation:
if Overflow bit is ‘0’
(PC) + 2 + 2n → PC
Operation:
if Zero bit is ‘0’
(PC) + 2 + 2n → PC
Status Affected:
None
Status Affected:
None
Encoding:
1110
0101
nnnn
nnnn
Encoding:
1110
0001
nnnn
nnnn
Description:
If the Overflow bit is ‘0’, then the
program will branch.
The 2’s complement number ‘2n’ is
added to the PC. Since the PC will have
incremented to fetch the next
instruction, the new address will be
PC + 2 + 2n. This instruction is then a
two-cycle instruction.
Description:
If the Zero bit is ‘0’, then the program
will branch.
The 2’s complement number ‘2n’ is
added to the PC. Since the PC will have
incremented to fetch the next
instruction, the new address will be
PC + 2 + 2n. This instruction is then a
two-cycle instruction.
Words:
1
Words:
1
Cycles:
1(2)
Cycles:
1(2)
Q Cycle Activity:
If Jump:
Q Cycle Activity:
If Jump:
Q1
Q2
Q3
Q4
Q1
Q2
Q3
Q4
Decode
Read literal
‘n’
Process
Data
Write to PC
Decode
Read literal
‘n’
Process
Data
Write to PC
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
Q1
Q2
Q3
Q4
Q1
Q2
Q3
Q4
Decode
Read literal
‘n’
Process
Data
No
operation
Decode
Read literal
‘n’
Process
Data
No
operation
If No Jump:
If No Jump:
Example:
HERE
Before Instruction
PC
After Instruction
If Overflow
PC
If Overflow
PC
DS39636A-page 268
BNOV Jump
=
address (HERE)
=
=
=
=
0;
address (Jump)
1;
address (HERE + 2)
Example:
HERE
Before Instruction
PC
After Instruction
If Zero
PC
If Zero
PC
Preliminary
BNZ
Jump
=
address (HERE)
=
=
=
=
0;
address (Jump)
1;
address (HERE + 2)
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
BRA
Unconditional Branch
BSF
Bit Set f
Syntax:
BRA
Syntax:
BSF
Operands:
0 ≤ f ≤ 255
0≤b≤7
a ∈ [0,1]
Operation:
1 → f<b>
Status Affected:
None
n
Operands:
-1024 ≤ n ≤ 1023
Operation:
(PC) + 2 + 2n → PC
Status Affected:
None
Encoding:
1101
Description:
0nnn
nnnn
nnnn
Add the 2’s complement number ‘2n’ to
the PC. Since the PC will have incremented to fetch the next instruction, the
new address will be PC + 2 + 2n. This
instruction is a two-cycle instruction.
Words:
1
Cycles:
2
Encoding:
1000
Q1
Q2
Q3
Q4
Read literal
‘n’
Process
Data
Write to PC
No
operation
No
operation
No
operation
No
operation
bbba
ffff
ffff
Description:
Bit ‘b’ in register ‘f’ is set.
If ‘a’ is ‘0’, the Access Bank is selected.
If ‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates
in Indexed Literal Offset Addressing
mode whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
Words:
1
Cycles:
1
Q Cycle Activity:
Decode
f, b {,a}
Q Cycle Activity:
Example:
HERE
Before Instruction
PC
After Instruction
PC
BRA
Jump
=
address (HERE)
=
address (Jump)
Q1
Q2
Q3
Q4
Decode
Read
register ‘f’
Process
Data
Write
register ‘f’
Example:
BSF
Before Instruction
FLAG_REG
After Instruction
FLAG_REG
 2004 Microchip Technology Inc.
Preliminary
FLAG_REG, 7, 1
=
0Ah
=
8Ah
DS39636A-page 269
PIC18F2X1X/4X1X
BTFSC
Bit Test File, Skip if Clear
BTFSS
Bit Test File, Skip if Set
Syntax:
BTFSC f, b {,a}
Syntax:
BTFSS f, b {,a}
Operands:
0 ≤ f ≤ 255
0≤b≤7
a ∈ [0,1]
Operands:
0 ≤ f ≤ 255
0≤b<7
a ∈ [0,1]
Operation:
skip if (f<b>) = 0
Operation:
skip if (f<b>) = 1
Status Affected:
None
Status Affected:
None
Encoding:
1011
Description:
bbba
ffff
ffff
Encoding:
1010
If bit ‘b’ in register ‘f’ is ‘0’, then the next
instruction is skipped. If bit ‘b’ is ‘0’, then
the next instruction fetched during the
current instruction execution is discarded
and a NOP is executed instead, making
this a two-cycle instruction.
If ‘a’ is ‘0’, the Access Bank is selected. If
‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates in
Indexed Literal Offset Addressing
mode whenever f ≤ 95 (5Fh).
See Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
Description:
Words:
1
Words:
1
Cycles:
1(2)
Note: 3 cycles if skip and followed
by a 2-word instruction.
Cycles:
1(2)
Note:
Q Cycle Activity:
bbba
ffff
ffff
If bit ‘b’ in register ‘f’ is ‘1’, then the next
instruction is skipped. If bit ‘b’ is ‘1’, then
the next instruction fetched during the
current instruction execution is discarded
and a NOP is executed instead, making
this a two-cycle instruction.
If ‘a’ is ‘0’, the Access Bank is selected. If
‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates
in Indexed Literal Offset Addressing
mode whenever f ≤ 95 (5Fh).
See Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
3 cycles if skip and followed
by a 2-word instruction.
Q Cycle Activity:
Q1
Q2
Q3
Q4
Q1
Q2
Q3
Q4
Decode
Read
register ‘f’
Process
Data
No
operation
Decode
Read
register ‘f’
Process
Data
No
operation
Q1
Q2
Q3
Q4
Q1
Q2
Q3
Q4
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
If skip:
If skip:
If skip and followed by 2-word instruction:
If skip and followed by 2-word instruction:
Q1
Q2
Q3
Q4
Q1
Q2
Q3
Q4
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
Example:
HERE
FALSE
TRUE
Before Instruction
PC
After Instruction
If FLAG<1>
PC
If FLAG<1>
PC
DS39636A-page 270
BTFSC
:
:
FLAG, 1, 0
=
address (HERE)
=
=
=
=
0;
address (TRUE)
1;
address (FALSE)
Example:
HERE
FALSE
TRUE
Before Instruction
PC
After Instruction
If FLAG<1>
PC
If FLAG<1>
PC
Preliminary
BTFSS
:
:
FLAG, 1, 0
=
address (HERE)
=
=
=
=
0;
address (FALSE)
1;
address (TRUE)
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
BTG
Bit Toggle f
BOV
Branch if Overflow
Syntax:
BTG f, b {,a}
Syntax:
BOV
Operands:
0 ≤ f ≤ 255
0≤b<7
a ∈ [0,1]
Operands:
-128 ≤ n ≤ 127
Operation:
if Overflow bit is ‘1’
(PC) + 2 + 2n → PC
Status Affected:
None
Operation:
(f<b>) → f<b>
Status Affected:
None
Encoding:
0111
Description:
Encoding:
bbba
ffff
ffff
Bit ‘b’ in data memory location ‘f’ is
inverted.
If ‘a’ is ‘0’, the Access Bank is selected.
If ‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates
in Indexed Literal Offset Addressing
mode whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
n
1110
0100
nnnn
nnnn
Description:
If the Overflow bit is ‘1’, then the
program will branch.
The 2’s complement number ‘2n’ is
added to the PC. Since the PC will have
incremented to fetch the next
instruction, the new address will be
PC + 2 + 2n. This instruction is then a
two-cycle instruction.
Words:
1
Cycles:
1(2)
Q Cycle Activity:
If Jump:
Words:
1
Q1
Q2
Q3
Q4
Cycles:
1
Decode
Read literal
‘n’
Process
Data
Write to PC
No
operation
No
operation
No
operation
No
operation
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
register ‘f’
Process
Data
Write
register ‘f’
Example:
BTG
PORTC,
Q1
Q2
Q3
Q4
Decode
Read literal
‘n’
Process
Data
No
operation
4, 0
Before Instruction:
PORTC =
0111 0101 [75h]
After Instruction:
PORTC =
0110 0101 [65h]
 2004 Microchip Technology Inc.
If No Jump:
Example:
HERE
Before Instruction
PC
After Instruction
If Overflow
PC
If Overflow
PC
Preliminary
BOV
Jump
=
address (HERE)
=
=
=
=
1;
address (Jump)
0;
address (HERE + 2)
DS39636A-page 271
PIC18F2X1X/4X1X
BZ
Branch if Zero
CALL
Subroutine Call
Syntax:
BZ
Syntax:
CALL k {,s}
n
Operands:
-128 ≤ n ≤ 127
Operands:
Operation:
if Zero bit is ‘1’
(PC) + 2 + 2n → PC
0 ≤ k ≤ 1048575
s ∈ [0,1]
Operation:
Status Affected:
None
(PC) + 4 → TOS,
k → PC<20:1>,
if s = 1
(W) → WS,
(Status) → STATUSS,
(BSR) → BSRS
Status Affected:
None
Encoding:
1110
Description:
0000
nnnn
nnnn
If the Zero bit is ‘1’, then the program
will branch.
The 2’s complement number ‘2n’ is
added to the PC. Since the PC will have
incremented to fetch the next
instruction, the new address will be
PC + 2 + 2n. This instruction is then a
two-cycle instruction.
Words:
1
Cycles:
1(2)
Encoding:
1st word (k<7:0>)
2nd word(k<19:8>)
Q1
Q2
Q3
Q4
Read literal
‘n’
Process
Data
Write to PC
No
operation
No
operation
No
operation
No
operation
If No Jump:
Q2
Q3
Q4
Read literal
‘n’
Process
Data
No
operation
HERE
Before Instruction
PC
After Instruction
If Zero
PC
If Zero
PC
DS39636A-page 272
BZ
Subroutine call of entire 2-Mbyte
memory range. First, return address
(PC + 4) is pushed onto the return
stack. If ‘s’ = 1, the W, Status and BSR
registers are also pushed into their
respective shadow registers, WS,
STATUSS and BSRS. If ‘s’ = 0, no
update occurs (default). Then, the
20-bit value ‘k’ is loaded into PC<20:1>.
CALL is a two-cycle instruction.
Words:
2
Cycles:
2
Q1
Q2
Q3
Q4
Decode
Read literal
‘k’<7:0>,
Push PC to
stack
Read literal
‘k’<19:8>,
Write to PC
No
operation
No
operation
No
operation
No
operation
Jump
=
address (HERE)
=
=
=
=
1;
address (Jump)
0;
address (HERE + 2)
kkkk0
kkkk8
Q Cycle Activity:
Q1
Decode
Example:
k7kkk
kkkk
110s
k19kkk
Description:
Q Cycle Activity:
If Jump:
Decode
1110
1111
Example:
HERE
Before Instruction
PC
=
After Instruction
PC
=
TOS
=
WS
=
BSRS
=
STATUSS =
Preliminary
CALL
THERE,1
address (HERE)
address (THERE)
address (HERE + 4)
W
BSR
Status
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
CLRF
Clear f
Syntax:
CLRF
Operands:
0 ≤ f ≤ 255
a ∈ [0,1]
f {,a}
Operation:
000h → f
1→Z
Status Affected:
Z
Encoding:
0110
Description:
101a
ffff
ffff
Clears the contents of the specified
register.
If ‘a’ is ‘0’, the Access Bank is selected.
If ‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates
in Indexed Literal Offset Addressing
mode whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
Words:
1
Cycles:
1
CLRWDT
Clear Watchdog Timer
Syntax:
CLRWDT
Operands:
None
Operation:
000h → WDT,
000h → WDT postscaler,
1 → TO,
1 → PD
Status Affected:
TO, PD
Encoding:
Words:
1
Cycles:
Q3
Q4
Decode
Read
register ‘f’
Process
Data
Write
register ‘f’
Example:
CLRF
Before Instruction
FLAG_REG
After Instruction
FLAG_REG
1
FLAG_REG,1
=
5Ah
=
00h
 2004 Microchip Technology Inc.
0000
0100
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
No
operation
Process
Data
No
operation
Example:
Q2
0000
CLRWDT instruction resets the
Watchdog Timer. It also resets the
postscaler of the WDT. Status bits TO
and PD are set.
Q Cycle Activity:
Q1
0000
Description:
Preliminary
CLRWDT
Before Instruction
WDT Counter
After Instruction
WDT Counter
WDT Postscaler
TO
PD
=
?
=
=
=
=
00h
0
1
1
DS39636A-page 273
PIC18F2X1X/4X1X
COMF
Complement f
CPFSEQ
Compare f with W, Skip if f = W
Syntax:
COMF
Syntax:
CPFSEQ
Operands:
0 ≤ f ≤ 255
a ∈ [0,1]
Operation:
(f) – (W),
skip if (f) = (W)
(unsigned comparison)
Status Affected:
None
f {,d {,a}}
0 ≤ f ≤ 255
d ∈ [0,1]
a ∈ [0,1]
Operands:
Operation:
( f ) → dest
Status Affected:
N, Z
Encoding:
0001
11da
ffff
ffff
Description:
The contents of register ‘f’ are
complemented. If ‘d’ is ‘0’, the result is
stored in W. If ‘d’ is ‘1’, the result is
stored back in register ‘f’ (default).
If ‘a’ is ‘0’, the Access Bank is selected.
If ‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates
in Indexed Literal Offset Addressing
mode whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
Words:
1
Cycles:
1
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
register ‘f’
Process
Data
Write to
destination
Encoding:
0110
f {,a}
001a
ffff
ffff
Description:
Compares the contents of data memory
location ‘f’ to the contents of W by
performing an unsigned subtraction.
If ‘f’ = W, then the fetched instruction is
discarded and a NOP is executed
instead, making this a two-cycle
instruction.
If ‘a’ is ‘0’, the Access Bank is selected.
If ‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates
in Indexed Literal Offset Addressing
mode whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
Words:
1
Cycles:
1(2)
Note: 3 cycles if skip and followed
by a 2-word instruction.
Q Cycle Activity:
Example:
COMF
Before Instruction
REG
=
After Instruction
REG
=
W
=
REG, 0, 0
Q1
Q2
Q3
Q4
Decode
Read
register ‘f’
Process
Data
No
operation
13h
If skip:
13h
ECh
Q1
Q2
Q3
No
No
No
operation
operation
operation
If skip and followed by 2-word instruction:
Q1
Q2
Q3
No
No
No
operation
operation
operation
No
No
No
operation
operation
operation
Example:
DS39636A-page 274
Preliminary
HERE
NEQUAL
EQUAL
Q4
No
operation
Q4
No
operation
No
operation
CPFSEQ REG, 0
:
:
Before Instruction
PC Address
W
REG
After Instruction
=
=
=
HERE
?
?
If REG
PC
If REG
PC
=
=
≠
=
W;
Address (EQUAL)
W;
Address (NEQUAL)
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
CPFSGT
Compare f with W, Skip if f > W
CPFSLT
Compare f with W, Skip if f < W
Syntax:
CPFSGT
Syntax:
CPFSLT
Operands:
0 ≤ f ≤ 255
a ∈ [0,1]
Operands:
Operation:
(f) − (W),
skip if (f) > (W)
(unsigned comparison)
0 ≤ f ≤ 255
a ∈ [0,1]
Operation:
(f) – (W),
skip if (f) < (W)
(unsigned comparison)
Status Affected:
None
Status Affected:
None
Encoding:
0110
Description:
f {,a}
010a
ffff
ffff
Compares the contents of data memory
location ‘f’ to the contents of the W by
performing an unsigned subtraction.
If the contents of ‘f’ are greater than the
contents of WREG, then the fetched
instruction is discarded and a NOP is
executed instead, making this a
two-cycle instruction.
If ‘a’ is ‘0’, the Access Bank is selected.
If ‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates
in Indexed Literal Offset Addressing
mode whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
Words:
1
Cycles:
1(2)
Note: 3 cycles if skip and followed
by a 2-word instruction.
Encoding:
Q2
Read
register ‘f’
Q3
Process
Data
Q4
No
operation
Q1
Q2
Q3
No
No
No
operation
operation
operation
If skip and followed by 2-word instruction:
Q1
Q2
Q3
No
No
No
operation
operation
operation
No
No
No
operation
operation
operation
Q4
No
operation
Example:
HERE
NGREATER
GREATER
=
=
Address (HERE)
?
If REG
PC
If REG
PC
>
=
≤
=
W;
Address (GREATER)
W;
Address (NGREATER)
 2004 Microchip Technology Inc.
ffff
ffff
Words:
1
Cycles:
1(2)
Note:
3 cycles if skip and followed
by a 2-word instruction.
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
register ‘f’
Process
Data
No
operation
If skip:
Q1
Q2
Q3
Q4
No
operation
No
operation
No
operation
No
operation
If skip and followed by 2-word instruction:
Q1
Q2
Q3
Q4
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
Example:
CPFSGT REG, 0
:
:
Before Instruction
PC
W
After Instruction
000a
Compares the contents of data memory
location ‘f’ to the contents of W by
performing an unsigned subtraction.
If the contents of ‘f’ are less than the
contents of W, then the fetched
instruction is discarded and a NOP is
executed instead, making this a
two-cycle instruction.
If ‘a’ is ‘0’, the Access Bank is selected.
If ‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
If skip:
Q4
No
operation
No
operation
0110
Description:
Q Cycle Activity:
Q1
Decode
f {,a}
Preliminary
HERE
NLESS
LESS
CPFSLT REG, 1
:
:
Before Instruction
PC
W
After Instruction
=
=
Address (HERE)
?
If REG
PC
If REG
PC
<
=
≥
=
W;
Address (LESS)
W;
Address (NLESS)
DS39636A-page 275
PIC18F2X1X/4X1X
DAW
Decimal Adjust W Register
DECF
Decrement f
Syntax:
DAW
Syntax:
DECF f {,d {,a}}
Operands:
None
Operands:
Operation:
If [W<3:0> > 9] or [DC = 1] then
(W<3:0>) + 6 → W<3:0>;
else
(W<3:0>) → W<3:0>;
0 ≤ f ≤ 255
d ∈ [0,1]
a ∈ [0,1]
Operation:
(f) – 1 → dest
Status Affected:
C, DC, N, OV, Z
If [W<7:4> + DC > 9] or [C = 1] then
(W<7:4>) + 6 + DC → W<7:4> ;
else
(W<7:4>) + DC → W<7:4>
Status Affected:
Encoding:
0000
0000
0000
0000
DAW adjusts the eight-bit value in W,
resulting from the earlier addition of two
variables (each in packed BCD format)
and produces a correct packed BCD
result.
Words:
1
Cycles:
1
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
register W
Process
Data
Write
W
ffff
Decrement register ‘f’. If ‘d’ is ‘0’, the
result is stored in W. If ‘d’ is ‘1’, the
result is stored back in register ‘f’
(default).
If ‘a’ is ‘0’, the Access Bank is selected.
If ‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates
in Indexed Literal Offset Addressing
mode whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
Words:
1
Cycles:
1
0111
Description:
ffff
Description:
C
Encoding:
01da
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
register ‘f’
Process
Data
Write to
destination
Example 1:
DAW
Before Instruction
W
=
C
=
DC
=
After Instruction
W
C
DC
Example 2:
=
=
=
A5h
0
0
Example:
DECF
Before Instruction
CNT
=
Z
=
After Instruction
CNT
=
Z
=
05h
1
0
CNT,
1, 0
01h
0
00h
1
Before Instruction
W
=
C
=
DC
=
After Instruction
W
C
DC
=
=
=
DS39636A-page 276
CEh
0
0
34h
1
0
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
DECFSZ
Decrement f, Skip if 0
DCFSNZ
Decrement f, Skip if not 0
Syntax:
DECFSZ f {,d {,a}}
Syntax:
DCFSNZ
Operands:
0 ≤ f ≤ 255
d ∈ [0,1]
a ∈ [0,1]
Operands:
0 ≤ f ≤ 255
d ∈ [0,1]
a ∈ [0,1]
Operation:
(f) – 1 → dest,
skip if result = 0
Operation:
(f) – 1 → dest,
skip if result ≠ 0
Status Affected:
None
Status Affected:
None
Encoding:
0010
11da
ffff
ffff
Description:
The contents of register ‘f’ are
decremented. If ‘d’ is ‘0’, the result is
placed in W. If ‘d’ is ‘1’, the result is
placed back in register ‘f’ (default).
If the result is ‘0’, the next instruction,
which is already fetched, is discarded
and a NOP is executed instead, making
it a two-cycle instruction.
If ‘a’ is ‘0’, the Access Bank is selected.
If ‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates
in Indexed Literal Offset Addressing
mode whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
Words:
1
Cycles:
1(2)
Note: 3 cycles if skip and followed
by a 2-word instruction.
Encoding:
0100
Description:
11da
Q2
Q3
Q4
Decode
Read
register ‘f’
Process
Data
Write to
destination
Words:
1
Cycles:
1(2)
Note:
3 cycles if skip and followed
by a 2-word instruction.
Q1
Q2
Q3
Q4
Decode
Read
register ‘f’
Process
Data
Write to
destination
If skip:
If skip:
Q1
Q2
Q3
Q4
No
operation
No
operation
No
operation
No
operation
If skip and followed by 2-word instruction:
Q2
Q3
Q4
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
DECFSZ
GOTO
CNT, 1, 1
LOOP
Q2
Q3
Q4
No
operation
No
operation
No
operation
Q1
Q2
Q3
Q4
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
Example:
CONTINUE
HERE
ZERO
NZERO
Before Instruction
TEMP
After Instruction
TEMP
If TEMP
PC
If TEMP
PC
Address (HERE)
CNT – 1
0;
Address (CONTINUE)
0;
Address (HERE + 2)
 2004 Microchip Technology Inc.
Q1
No
operation
If skip and followed by 2-word instruction:
Q1
Before Instruction
PC
=
After Instruction
CNT
=
If CNT
=
PC =
If CNT
≠
PC =
ffff
Q Cycle Activity:
Q1
HERE
ffff
The contents of register ‘f’ are
decremented. If ‘d’ is ‘0’, the result is
placed in W. If ‘d’ is ‘1’, the result is
placed back in register ‘f’ (default).
If the result is not ‘0’, the next
instruction, which is already fetched, is
discarded and a NOP is executed
instead, making it a two-cycle
instruction.
If ‘a’ is ‘0’, the Access Bank is selected.
If ‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates
in Indexed Literal Offset Addressing
mode whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
Q Cycle Activity:
Example:
f {,d {,a}}
Preliminary
DCFSNZ
:
:
TEMP, 1, 0
=
?
=
=
=
≠
=
TEMP – 1,
0;
Address (ZERO)
0;
Address (NZERO)
DS39636A-page 277
PIC18F2X1X/4X1X
GOTO
Unconditional Branch
INCF
Increment f
Syntax:
GOTO k
Syntax:
INCF
Operands:
0 ≤ k ≤ 1048575
Operands:
Operation:
k → PC<20:1>
Status Affected:
None
0 ≤ f ≤ 255
d ∈ [0,1]
a ∈ [0,1]
Operation:
(f) + 1 → dest
Status Affected:
C, DC, N, OV, Z
Encoding:
1st word (k<7:0>)
2nd word(k<19:8>)
1110
1111
Description:
1111
k19kkk
k7kkk
kkkk
kkkk0
kkkk8
GOTO allows an unconditional branch
Encoding:
0010
2
Cycles:
2
Q1
Q2
Q3
Q4
Read literal
‘k’<7:0>,
No
operation
Read literal
‘k’<19:8>,
Write to PC
No
operation
No
operation
No
operation
No
operation
ffff
ffff
The contents of register ‘f’ are
incremented. If ‘d’ is ‘0’, the result is
placed in W. If ‘d’ is ‘1’, the result is
placed back in register ‘f’ (default).
If ‘a’ is ‘0’, the Access Bank is selected.
If ‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates
in Indexed Literal Offset Addressing
mode whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
Words:
1
Cycles:
1
Q Cycle Activity:
Decode
10da
Description:
anywhere within entire
2-Mbyte memory range. The 20-bit
value ‘k’ is loaded into PC<20:1>.
GOTO is always a two-cycle
instruction.
Words:
f {,d {,a}}
Q Cycle Activity:
Example:
GOTO THERE
After Instruction
PC =
Address (THERE)
Q1
Q2
Q3
Q4
Decode
Read
register ‘f’
Process
Data
Write to
destination
Example:
INCF
Before Instruction
CNT
=
Z
=
C
=
DC
=
After Instruction
CNT
=
Z
=
C
=
DC
=
DS39636A-page 278
Preliminary
CNT, 1, 0
FFh
0
?
?
00h
1
1
1
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
INCFSZ
Increment f, Skip if 0
INFSNZ
Syntax:
INCFSZ
Syntax:
INFSNZ
0 ≤ f ≤ 255
d ∈ [0,1]
a ∈ [0,1]
f {,d {,a}}
Increment f, Skip if not 0
f {,d {,a}}
Operands:
0 ≤ f ≤ 255
d ∈ [0,1]
a ∈ [0,1]
Operands:
Operation:
(f) + 1 → dest,
skip if result = 0
Operation:
(f) + 1 → dest,
skip if result ≠ 0
Status Affected:
None
Status Affected:
None
Encoding:
0011
11da
ffff
ffff
Encoding:
0100
Description:
ffff
ffff
The contents of register ‘f’ are
incremented. If ‘d’ is ‘0’, the result is
placed in W. If ‘d’ is ‘1’, the result is
placed back in register ‘f’ (default).
If the result is not ‘0’, the next
instruction, which is already fetched, is
discarded and a NOP is executed
instead, making it a two-cycle
instruction.
If ‘a’ is ‘0’, the Access Bank is selected.
If ‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates
in Indexed Literal Offset Addressing
mode whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
Description:
The contents of register ‘f’ are
incremented. If ‘d’ is ‘0’, the result is
placed in W. If ‘d’ is ‘1’, the result is
placed back in register ‘f’. (default)
If the result is ‘0’, the next instruction,
which is already fetched, is discarded
and a NOP is executed instead, making
it a two-cycle instruction.
If ‘a’ is ‘0’, the Access Bank is selected.
If ‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates
in Indexed Literal Offset Addressing
mode whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
Words:
1
Words:
1
Cycles:
1(2)
Note: 3 cycles if skip and followed
by a 2-word instruction.
Cycles:
1(2)
Note:
Q Cycle Activity:
10da
3 cycles if skip and followed
by a 2-word instruction.
Q Cycle Activity:
Q1
Q2
Q3
Q4
Q1
Q2
Q3
Q4
Decode
Read
register ‘f’
Process
Data
Write to
destination
Decode
Read
register ‘f’
Process
Data
Write to
destination
Q1
Q2
Q3
Q4
Q1
Q2
Q3
Q4
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
If skip:
If skip:
If skip and followed by 2-word instruction:
If skip and followed by 2-word instruction:
Q1
Q2
Q3
Q4
Q1
Q2
Q3
Q4
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
Example:
HERE
NZERO
ZERO
Before Instruction
PC
=
After Instruction
CNT
=
If CNT
=
PC
=
If CNT
≠
PC
=
INCFSZ
:
:
CNT, 1, 0
Example:
Before Instruction
PC
=
After Instruction
REG
=
≠
If REG
PC
=
If REG
=
PC
=
Address (HERE)
CNT + 1
0;
Address (ZERO)
0;
Address (NZERO)
 2004 Microchip Technology Inc.
HERE
ZERO
NZERO
Preliminary
INFSNZ
REG, 1, 0
Address (HERE)
REG + 1
0;
Address (NZERO)
0;
Address (ZERO)
DS39636A-page 279
PIC18F2X1X/4X1X
IORLW
Inclusive OR Literal with W
IORWF
Inclusive OR W with f
Syntax:
IORLW k
Syntax:
IORWF
Operands:
0 ≤ k ≤ 255
Operands:
Operation:
(W) .OR. k → W
Status Affected:
N, Z
0 ≤ f ≤ 255
d ∈ [0,1]
a ∈ [0,1]
Operation:
(W) .OR. (f) → dest
Status Affected:
N, Z
Encoding:
0000
1001
kkkk
kkkk
Description:
The contents of W are ORed with the
eight-bit literal ‘k’. The result is placed
in W.
Words:
1
Cycles:
1
Encoding:
0001
Q1
Q2
Q3
Q4
Read
literal ‘k’
Process
Data
Write to W
Example:
IORLW
W
=
ffff
Words:
1
Cycles:
1
35h
9Ah
BFh
ffff
Inclusive OR W with register ‘f’. If ‘d’ is
‘0’, the result is placed in W. If ‘d’ is ‘1’,
the result is placed back in register ‘f’
(default).
If ‘a’ is ‘0’, the Access Bank is selected.
If ‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates
in Indexed Literal Offset Addressing
mode whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
Before Instruction
W
=
After Instruction
00da
Description:
Q Cycle Activity:
Decode
f {,d {,a}}
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
register ‘f’
Process
Data
Write to
destination
Example:
IORWF
Before Instruction
RESULT =
W
=
After Instruction
RESULT =
W
=
DS39636A-page 280
Preliminary
RESULT, 0, 1
13h
91h
13h
93h
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
LFSR
Load FSR
MOVF
Move f
Syntax:
LFSR f, k
Syntax:
MOVF
Operands:
0≤f≤2
0 ≤ k ≤ 4095
Operands:
Operation:
k → FSRf
0 ≤ f ≤ 255
d ∈ [0,1]
a ∈ [0,1]
Status Affected:
None
Operation:
f → dest
Status Affected:
N, Z
Encoding:
1110
1111
1110
0000
00ff
k7kkk
k11kkk
kkkk
Description:
The 12-bit literal ‘k’ is loaded into the
File Select Register pointed to by ‘f’.
Words:
2
Cycles:
2
Encoding:
0101
Q1
Q2
Q3
Q4
Read literal
‘k’ MSB
Process
Data
Write
literal ‘k’
MSB to
FSRfH
Decode
Read literal
‘k’ LSB
Process
Data
Write literal
‘k’ to FSRfL
Example:
After Instruction
FSR2H
FSR2L
03h
ABh
ffff
ffff
The contents of register ‘f’ are moved to
a destination dependent upon the
status of ‘d’. If ‘d’ is ‘0’, the result is
placed in W. If ‘d’ is ‘1’, the result is
placed back in register ‘f’ (default).
Location ‘f’ can be anywhere in the
256-byte bank.
If ‘a’ is ‘0’, the Access Bank is selected.
If ‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates
in Indexed Literal Offset Addressing
mode whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
Words:
1
Cycles:
1
LFSR 2, 3ABh
=
=
00da
Description:
Q Cycle Activity:
Decode
f {,d {,a}}
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
register ‘f’
Process
Data
Write W
Example:
MOVF
Before Instruction
REG
W
After Instruction
REG
W
 2004 Microchip Technology Inc.
Preliminary
REG, 0, 0
=
=
22h
FFh
=
=
22h
22h
DS39636A-page 281
PIC18F2X1X/4X1X
MOVFF
Move f to f
MOVLB
Move Literal to Low Nibble in BSR
Syntax:
MOVFF fs,fd
Syntax:
MOVLW k
Operands:
0 ≤ fs ≤ 4095
0 ≤ fd ≤ 4095
Operands:
0 ≤ k ≤ 255
Operation:
k → BSR
None
Operation:
(fs) → fd
Status Affected:
Status Affected:
None
Encoding:
Encoding:
1st word (source)
2nd word (destin.)
1100
1111
Description:
ffff
ffff
ffff
ffff
ffffs
ffffd
The contents of source register ‘fs’ are
moved to destination register ‘fd’.
Location of source ‘fs’ can be anywhere
in the 4096-byte data space (000h to
FFFh) and location of destination ‘fd’
can also be anywhere from 000h to
FFFh.
Either source or destination can be W
(a useful special situation).
MOVFF is particularly useful for
transferring a data memory location to a
peripheral register (such as the transmit
buffer or an I/O port).
The MOVFF instruction cannot use the
PCL, TOSU, TOSH or TOSL as the
destination register.
Words:
2
Cycles:
2 (3)
0000
0001
kkkk
kkkk
Description:
The eight-bit literal ‘k’ is loaded into the
Bank Select Register (BSR). The value
of BSR<7:4> always remains ‘0’,
regardless of the value of k7:k4.
Words:
1
Cycles:
1
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
literal ‘k’
Process
Data
Write literal
‘k’ to BSR
MOVLB
5
Example:
Before Instruction
BSR Register =
After Instruction
BSR Register =
02h
05h
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
register ‘f’
(src)
Process
Data
No
operation
Decode
No
operation
No
operation
Write
register ‘f’
(dest)
No dummy
read
Example:
MOVFF
Before Instruction
REG1
REG2
After Instruction
REG1
REG2
DS39636A-page 282
REG1, REG2
=
=
33h
11h
=
=
33h
33h
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
MOVLW
Move Literal to W
MOVWF
Move W to f
Syntax:
MOVLW k
Syntax:
MOVWF
Operands:
0 ≤ k ≤ 255
Operands:
Operation:
k→W
0 ≤ f ≤ 255
a ∈ [0,1]
Status Affected:
None
Encoding:
0000
Description:
1110
kkkk
kkkk
The eight-bit literal ‘k’ is loaded into W.
Words:
1
Cycles:
1
Operation:
(W) → f
Status Affected:
None
Encoding:
0110
Q1
Q2
Q3
Q4
Read
literal ‘k’
Process
Data
Write to W
Example:
MOVLW
=
ffff
ffff
Move data from W to register ‘f’.
Location ‘f’ can be anywhere in the
256-byte bank.
If ‘a’ is ‘0’, the Access Bank is selected.
If ‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates
in Indexed Literal Offset Addressing
mode whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
Words:
1
Cycles:
1
5Ah
After Instruction
W
111a
Description:
Q Cycle Activity:
Decode
f {,a}
5Ah
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
register ‘f’
Process
Data
Write
register ‘f’
Example:
MOVWF
REG, 0
Before Instruction
W
=
REG
=
After Instruction
W
REG
 2004 Microchip Technology Inc.
Preliminary
=
=
4Fh
FFh
4Fh
4Fh
DS39636A-page 283
PIC18F2X1X/4X1X
MULLW
Multiply Literal with W
MULWF
Multiply W with f
Syntax:
MULLW
Syntax:
MULWF
Operands:
0 ≤ f ≤ 255
a ∈ [0,1]
Operation:
(W) x (f) → PRODH:PRODL
Status Affected:
None
k
Operands:
0 ≤ k ≤ 255
Operation:
(W) x k → PRODH:PRODL
Status Affected:
None
Encoding:
0000
Description:
1101
kkkk
kkkk
An unsigned multiplication is carried
out between the contents of W and the
8-bit literal ‘k’. The 16-bit result is
placed in PRODH:PRODL register pair.
PRODH contains the high byte.
W is unchanged.
None of the status flags are affected.
Note that neither overflow nor carry is
possible in this operation. A zero result
is possible but not detected.
Words:
1
Cycles:
1
Encoding:
0000
Q1
Q2
Q3
Q4
Read
literal ‘k’
Process
Data
Write
registers
PRODH:
PRODL
Example:
MULLW
W
PRODH
PRODL
E2h
?
?
=
=
=
E2h
ADh
08h
ffff
Words:
1
Cycles:
1
0C4h
=
=
=
ffff
An unsigned multiplication is carried
out between the contents of W and the
register file location ‘f’. The 16-bit
result is stored in the PRODH:PRODL
register pair. PRODH contains the
high byte. Both W and ‘f’ are
unchanged.
None of the status flags are affected.
Note that neither overflow nor carry is
possible in this operation. A zero
result is possible but not detected.
If ‘a’ is ‘0’, the Access Bank is
selected. If ‘a’ is ‘1’, the BSR is used
to select the GPR bank (default).
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction
operates in Indexed Literal Offset
Addressing mode whenever
f ≤ 95 (5Fh). See Section 23.2.3
“Byte-Oriented and Bit-Oriented
Instructions in Indexed Literal Offset
Mode” for details.
Before Instruction
W
PRODH
PRODL
After Instruction
001a
Description:
Q Cycle Activity:
Decode
f {,a}
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
register ‘f’
Process
Data
Write
registers
PRODH:
PRODL
Example:
MULWF
REG, 1
Before Instruction
W
REG
PRODH
PRODL
After Instruction
W
REG
PRODH
PRODL
DS39636A-page 284
Preliminary
=
=
=
=
C4h
B5h
?
?
=
=
=
=
C4h
B5h
8Ah
94h
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
NEGF
Negate f
NOP
No Operation
Syntax:
NEGF
Syntax:
NOP
Operands:
0 ≤ f ≤ 255
a ∈ [0,1]
f {,a}
Operands:
None
Operation:
No operation
None
Operation:
(f)+1→f
Status Affected:
Status Affected:
N, OV, C, DC, Z
Encoding:
Encoding:
0110
Description:
110a
ffff
Location ‘f’ is negated using two’s
complement. The result is placed in the
data memory location ‘f’.
If ‘a’ is ‘0’, the Access Bank is selected.
If ‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates
in Indexed Literal Offset Addressing
mode whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
Words:
1
Cycles:
1
0000
1111
ffff
0000
xxxx
Description:
No operation.
Words:
1
Cycles:
1
0000
xxxx
0000
xxxx
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
No
operation
No
operation
No
operation
Example:
None.
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
register ‘f’
Process
Data
Write
register ‘f’
Example:
NEGF
Before Instruction
REG
=
After Instruction
REG
=
REG, 1
0011 1010 [3Ah]
1100 0110 [C6h]
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 285
PIC18F2X1X/4X1X
POP
Pop Top of Return Stack
PUSH
Push Top of Return Stack
Syntax:
POP
Syntax:
PUSH
Operands:
None
Operands:
None
Operation:
(TOS) → bit bucket
Operation:
(PC + 2) → TOS
Status Affected:
None
Status Affected:
None
Encoding:
0000
0000
0000
0110
Description:
The TOS value is pulled off the return
stack and is discarded. The TOS value
then becomes the previous value that
was pushed onto the return stack.
This instruction is provided to enable
the user to properly manage the return
stack to incorporate a software stack.
Words:
1
Cycles:
1
Encoding:
Q2
Q3
Q4
Decode
No
operation
POP TOS
value
No
operation
POP
GOTO
NEW
Before Instruction
TOS
Stack (1 level down)
DS39636A-page 286
0000
0101
The PC + 2 is pushed onto the top of
the return stack. The previous TOS
value is pushed down on the stack.
This instruction allows implementing a
software stack by modifying TOS and
then pushing it onto the return stack.
Words:
1
Cycles:
1
Q Cycle Activity:
Q1
After Instruction
TOS
PC
0000
Description:
Q Cycle Activity:
Example:
0000
Q1
Q2
Q3
Q4
Decode
PUSH
PC + 2 onto
return stack
No
operation
No
operation
Example:
=
=
=
=
0031A2h
014332h
014332h
NEW
Preliminary
PUSH
Before Instruction
TOS
PC
=
=
345Ah
0124h
After Instruction
PC
TOS
Stack (1 level down)
=
=
=
0126h
0126h
345Ah
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
RCALL
Relative Call
RESET
Reset
Syntax:
RCALL
Syntax:
RESET
n
Operands:
-1024 ≤ n ≤ 1023
Operands:
None
Operation:
(PC) + 2 → TOS,
(PC) + 2 + 2n → PC
Operation:
Reset all registers and flags that are
affected by a MCLR Reset.
Status Affected:
None
Status Affected:
All
Encoding:
1101
Description:
1nnn
nnnn
nnnn
Subroutine call with a jump up to 1K
from the current location. First, return
address (PC+2) is pushed onto the
stack. Then, add the 2’s complement
number ‘2n’ to the PC. Since the PC will
have incremented to fetch the next
instruction, the new address will be
PC+2+2n. This instruction is a
two-cycle instruction.
Words:
1
Cycles:
2
Encoding:
0000
Q3
Q4
Decode
Read literal
‘n’
Process
Data
Write to PC
No
operation
No
operation
1111
Words:
1
Cycles:
1
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Start
Reset
No
operation
No
operation
Example:
Q2
1111
This instruction provides a way to
execute a MCLR Reset in software.
Q Cycle Activity:
Q1
0000
Description:
After Instruction
Registers =
Flags*
=
RESET
Reset Value
Reset Value
Push PC to
stack
No
operation
Example:
No
operation
HERE
RCALL Jump
Before Instruction
PC =
Address (HERE)
After Instruction
PC =
Address (Jump)
TOS =
Address (HERE + 2)
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 287
PIC18F2X1X/4X1X
RETFIE
Return from Interrupt
RETLW
Return Literal to W
Syntax:
RETFIE {s}
Syntax:
RETLW k
Operands:
s ∈ [0,1]
Operands:
0 ≤ k ≤ 255
Operation:
(TOS) → PC,
1 → GIE/GIEH or PEIE/GIEL,
if s = 1
(WS) → W,
(STATUSS) → Status,
(BSRS) → BSR,
PCLATU, PCLATH are unchanged.
Operation:
k → W,
(TOS) → PC,
PCLATU, PCLATH are unchanged
Status Affected:
None
Status Affected:
Encoding:
0000
Description:
0000
0001
Words:
1
Cycles:
2
Q Cycle Activity:
kkkk
kkkk
W is loaded with the eight-bit literal ‘k’.
The program counter is loaded from the
top of the stack (the return address).
The high address latch (PCLATH)
remains unchanged.
Words:
1
Cycles:
2
000s
Return from Interrupt. Stack is popped
and Top-of-Stack (TOS) is loaded into
the PC. Interrupts are enabled by
setting either the high or low priority
global interrupt enable bit. If ‘s’ = 1, the
contents of the shadow registers WS,
STATUSS and BSRS are loaded into
their corresponding registers, W,
Status and BSR. If ‘s’ = 0, no update of
these registers occurs (default).
1100
Description:
GIE/GIEH, PEIE/GIEL.
Encoding:
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
literal ‘k’
Process
Data
POP PC
from stack,
Write to W
No
operation
No
operation
No
operation
No
operation
Example:
Q1
Q2
Q3
Q4
Decode
No
operation
No
operation
POP PC
from stack
Set GIEH or
GIEL
No
operation
0000
No
operation
Example:
RETFIE
After Interrupt
PC
W
BSR
Status
GIE/GIEH, PEIE/GIEL
DS39636A-page 288
No
operation
No
operation
1
=
=
=
=
=
TOS
WS
BSRS
STATUSS
1
CALL TABLE ;
;
;
;
:
TABLE
ADDWF PCL ;
RETLW k0
;
RETLW k1
;
:
:
RETLW kn
;
Before Instruction
W
=
After Instruction
W
=
Preliminary
W contains table
offset value
W now has
table value
W = offset
Begin table
End of table
07h
value of kn
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
RETURN
Return from Subroutine
RLCF
Rotate Left f through Carry
Syntax:
RETURN {s}
Syntax:
RLCF
Operands:
s ∈ [0,1]
Operands:
Operation:
(TOS) → PC,
if s = 1
(WS) → W,
(STATUSS) → Status,
(BSRS) → BSR,
PCLATU, PCLATH are unchanged
0 ≤ f ≤ 255
d ∈ [0,1]
a ∈ [0,1]
Operation:
(f<n>) → dest<n + 1>,
(f<7>) → C,
(C) → dest<0>
Status Affected:
C, N, Z
Status Affected:
None
Encoding:
0000
Encoding:
0000
0001
001s
Description:
Return from subroutine. The stack is
popped and the top of the stack (TOS)
is loaded into the program counter. If
‘s’= 1, the contents of the shadow
registers WS, STATUSS and BSRS are
loaded into their corresponding
registers, W, Status and BSR. If
‘s’ = 0, no update of these registers
occurs (default).
Words:
1
Cycles:
2
0011
Description:
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
No
operation
Process
Data
POP PC
from stack
No
operation
No
operation
No
operation
No
operation
f {,d {,a}}
01da
ffff
ffff
The contents of register ‘f’ are rotated
one bit to the left through the Carry
flag. If ‘d’ is ‘0’, the result is placed in
W. If ‘d’ is ‘1’, the result is stored back
in register ‘f’ (default).
If ‘a’ is ‘0’, the Access Bank is
selected. If ‘a’ is ‘1’, the BSR is used to
select the GPR bank (default).
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction
operates in Indexed Literal Offset
Addressing mode whenever
f ≤ 95 (5Fh). See Section 23.2.3
“Byte-Oriented and Bit-Oriented
Instructions in Indexed Literal Offset
Mode” for details.
register f
C
Words:
1
Cycles:
1
Q Cycle Activity:
Example:
RETURN
After Instruction:
PC = TOS
Q1
Q2
Q3
Q4
Decode
Read
register ‘f’
Process
Data
Write to
destination
Example:
Before Instruction
REG
=
C
=
After Instruction
REG
=
W
=
C
=
 2004 Microchip Technology Inc.
Preliminary
RLCF
REG, 0, 0
1110 0110
0
1110 0110
1100 1100
1
DS39636A-page 289
PIC18F2X1X/4X1X
RLNCF
Rotate Left f (no carry)
RRCF
Rotate Right f through Carry
Syntax:
RLNCF
Syntax:
RRCF
Operands:
0 ≤ f ≤ 255
d ∈ [0,1]
a ∈ [0,1]
Operands:
0 ≤ f ≤ 255
d ∈ [0,1]
a ∈ [0,1]
Operation:
(f<n>) → dest<n + 1>,
(f<7>) → dest<0>
Operation:
Status Affected:
N, Z
(f<n>) → dest<n – 1>,
(f<0>) → C,
(C) → dest<7>
Status Affected:
C, N, Z
Encoding:
0100
Description:
f {,d {,a}}
01da
ffff
ffff
The contents of register ‘f’ are rotated
one bit to the left. If ‘d’ is ‘0’, the result
is placed in W. If ‘d’ is ‘1’, the result is
stored back in register ‘f’ (default).
If ‘a’ is ‘0’, the Access Bank is selected.
If ‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates
in Indexed Literal Offset Addressing
mode whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
Encoding:
0011
Description:
register f
Words:
1
Cycles:
1
Q1
Q2
Q3
Q4
Decode
Read
register ‘f’
Process
Data
Write to
destination
Before Instruction
REG
=
After Instruction
REG
=
DS39636A-page 290
00da
RLNCF
Words:
1
Cycles:
1
ffff
register f
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
register ‘f’
Process
Data
Write to
destination
REG, 1, 0
1010 1011
ffff
The contents of register ‘f’ are rotated
one bit to the right through the Carry
flag. If ‘d’ is ‘0’, the result is placed in W.
If ‘d’ is ‘1’, the result is placed back in
register ‘f’ (default).
If ‘a’ is ‘0’, the Access Bank is selected.
If ‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates
in Indexed Literal Offset Addressing
mode whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
C
Q Cycle Activity:
Example:
f {,d {,a}}
Example:
RRCF
Before Instruction
REG
=
C
=
After Instruction
REG
=
W
=
C
=
0101 0111
Preliminary
REG, 0, 0
1110 0110
0
1110 0110
0111 0011
0
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
RRNCF
Rotate Right f (no carry)
SETF
Syntax:
RRNCF
Syntax:
SETF
Operands:
0 ≤ f ≤ 255
d ∈ [0,1]
a ∈ [0,1]
Operands:
0 ≤ f ≤ 255
a ∈ [0,1]
Operation:
(f<n>) → dest<n – 1>,
(f<0>) → dest<7>
FFh → f
Operation:
Status Affected:
None
Status Affected:
f {,d {,a}}
Encoding:
N, Z
Encoding:
0100
Description:
00da
ffff
ffff
The contents of register ‘f’ are rotated
one bit to the right. If ‘d’ is ‘0’, the result
is placed in W. If ‘d’ is ‘1’, the result is
placed back in register ‘f’ (default).
If ‘a’ is ‘0’, the Access Bank will be
selected, overriding the BSR value. If ‘a’
is ‘1’, then the bank will be selected as
per the BSR value (default).
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates
in Indexed Literal Offset Addressing
mode whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
1
Cycles:
1
Q2
Q3
Q4
Read
register ‘f’
Process
Data
Write to
destination
Example 1:
RRNCF
Before Instruction
REG
=
After Instruction
REG
=
Example 2:
100a
ffff
ffff
Words:
1
Cycles:
1
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
register ‘f’
Process
Data
Write
register ‘f’
Example:
Q1
0110
The contents of the specified register
are set to FFh.
If ‘a’ is ‘0’, the Access Bank is selected.
If ‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates
in Indexed Literal Offset Addressing
mode whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
Q Cycle Activity:
Decode
f {,a}
Description:
register f
Words:
Set f
SETF
Before Instruction
REG
After Instruction
REG
REG,1
=
5Ah
=
FFh
REG, 1, 0
1101 0111
1110 1011
RRNCF
REG, 0, 0
Before Instruction
W
=
REG
=
After Instruction
W
REG
=
=
?
1101 0111
1110 1011
1101 0111
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 291
PIC18F2X1X/4X1X
SLEEP
Enter Sleep mode
SUBFWB
Subtract f from W with Borrow
Syntax:
SLEEP
Syntax:
SUBFWB
Operands:
None
Operands:
Operation:
00h → WDT,
0 → WDT postscaler,
1 → TO,
0 → PD
0 ≤ f ≤ 255
d ∈ [0,1]
a ∈ [0,1]
Operation:
(W) – (f) – (C) → dest
Status Affected:
N, OV, C, DC, Z
Status Affected:
TO, PD
Encoding:
0000
Encoding:
0000
0000
0011
Description:
The Power-down status bit (PD) is
cleared. The Time-out status bit (TO)
is set. Watchdog Timer and its
postscaler are cleared.
The processor is put into Sleep mode
with the oscillator stopped.
Words:
1
Cycles:
1
0101
Q1
Q2
Q3
Q4
No
operation
Process
Data
Go to
Sleep
Example:
SLEEP
Before Instruction
TO =
?
?
PD =
DS39636A-page 292
ffff
ffff
Subtract register ‘f’ and Carry flag
(borrow) from W (2’s complement
method). If ‘d’ is ‘0’, the result is stored
in W. If ‘d’ is ‘1’, the result is stored in
register ‘f’ (default).
If ‘a’ is ‘0’, the Access Bank is
selected. If ‘a’ is ‘1’, the BSR is used
to select the GPR bank (default).
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction
operates in Indexed Literal Offset
Addressing mode whenever
f ≤ 95 (5Fh). See Section 23.2.3
“Byte-Oriented and Bit-Oriented
Instructions in Indexed Literal Offset
Mode” for details.
Words:
1
Cycles:
1
Q Cycle Activity:
After Instruction
1†
TO =
0
PD =
† If WDT causes wake-up, this bit is cleared.
01da
Description:
Q Cycle Activity:
Decode
f {,d {,a}}
Q1
Q2
Q3
Q4
Decode
Read
register ‘f’
Process
Data
Write to
destination
SUBFWB
REG, 1, 0
Example 1:
Before Instruction
REG
=
3
W
=
2
C
=
1
After Instruction
REG
=
FF
W
=
2
C
=
0
Z
=
0
N
=
1 ; result is negative
SUBFWB
REG, 0, 0
Example 2:
Before Instruction
REG
=
2
W
=
5
C
=
1
After Instruction
REG
=
2
W
=
3
C
=
1
Z
=
0
N
=
0 ; result is positive
SUBFWB
REG, 1, 0
Example 3:
Before Instruction
REG
=
1
W
=
2
C
=
0
After Instruction
REG
=
0
W
=
2
C
=
1
Z
=
1 ; result is zero
N
=
0
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
SUBLW
Subtract W from Literal
SUBWF
Subtract W from f
Syntax:
SUBLW k
Syntax:
SUBWF
Operands:
0 ≤ k ≤ 255
Operands:
Operation:
k – (W) → W
Status Affected:
N, OV, C, DC, Z
0 ≤ f ≤ 255
d ∈ [0,1]
a ∈ [0,1]
Operation:
(f) – (W) → dest
Status Affected:
N, OV, C, DC, Z
Encoding:
0000
1000
kkkk
kkkk
f {,d {,a}}
Description
W is subtracted from the eight-bit
literal ‘k’. The result is placed in W.
Encoding:
Words:
1
Description:
Cycles:
1
Subtract W from register ‘f’ (2’s
complement method). If ‘d’ is ‘0’, the
result is stored in W. If ‘d’ is ‘1’, the
result is stored back in register ‘f’
(default).
If ‘a’ is ‘0’, the Access Bank is
selected. If ‘a’ is ‘1’, the BSR is used
to select the GPR bank (default).
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction
operates in Indexed Literal Offset
Addressing mode whenever
f ≤ 95 (5Fh). See Section 23.2.3
“Byte-Oriented and Bit-Oriented
Instructions in Indexed Literal Offset
Mode” for details.
Words:
1
Cycles:
1
0101
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
literal ‘k’
Process
Data
Write to W
Example 1:
Before Instruction
W
=
C
=
After Instruction
W
=
C
=
Z
=
N
=
Example 2:
Before Instruction
W
=
C
=
After Instruction
W
=
C
=
Z
=
N
=
Example 3:
Before Instruction
W
=
C
=
After Instruction
W
=
C
=
Z
=
N
=
SUBLW
02h
01h
?
01h
1
; result is positive
0
0
SUBLW
ffff
ffff
02h
Q Cycle Activity:
02h
?
00h
1
; result is zero
1
0
SUBLW
11da
Q1
Q2
Q3
Q4
Decode
Read
register ‘f’
Process
Data
Write to
destination
SUBWF
REG, 1, 0
Example 1:
Before Instruction
REG
=
W
=
C
=
After Instruction
REG
=
W
=
C
=
Z
=
N
=
02h
03h
?
FFh ; (2’s complement)
0
; result is negative
0
1
Example 2:
Before Instruction
REG
=
W
=
C
=
After Instruction
REG
=
W
=
C
=
Z
=
N
=
Example 3:
Before Instruction
REG
=
W
=
C
=
After Instruction
REG
=
W
=
C
=
Z
=
N
=
 2004 Microchip Technology Inc.
Preliminary
3
2
?
1
2
1
0
0
SUBWF
; result is positive
REG, 0, 0
2
2
?
2
0
1
1
0
SUBWF
; result is zero
REG, 1, 0
1
2
?
FFh ;(2’s complement)
2
0 ; result is negative
0
1
DS39636A-page 293
PIC18F2X1X/4X1X
SUBWFB
Subtract W from f with Borrow
SWAPF
Swap f
Syntax:
SUBWFB
Syntax:
SWAPF f {,d {,a}}
Operands:
0 ≤ f ≤ 255
d ∈ [0,1]
a ∈ [0,1]
Operands:
0 ≤ f ≤ 255
d ∈ [0,1]
a ∈ [0,1]
Operation:
(f) – (W) – (C) → dest
Operation:
Status Affected:
N, OV, C, DC, Z
(f<3:0>) → dest<7:4>,
(f<7:4>) → dest<3:0>
Status Affected:
None
Encoding:
0101
Description:
f {,d {,a}}
10da
ffff
ffff
Subtract W and the Carry flag (borrow)
from register ‘f’ (2’s complement
method). If ‘d’ is ‘0’, the result is stored
in W. If ‘d’ is ‘1’, the result is stored back
in register ‘f’ (default).
If ‘a’ is ‘0’, the Access Bank is selected.
If ‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates
in Indexed Literal Offset Addressing
mode whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
Words:
1
Cycles:
1
Q Cycle Activity:
Q1
Decode
Q2
Read
register ‘f’
Example 1:
SUBWFB
Before Instruction
REG
=
W
=
C
=
After Instruction
REG
=
W
=
C
=
Z
=
N
=
Example 2:
Q4
Write to
destination
(0001 1001)
(0000 1101)
0Ch
0Dh
1
0
0
(0000 1011)
(0000 1101)
10da
ffff
ffff
The upper and lower nibbles of register
‘f’ are exchanged. If ‘d’ is ‘0’, the result
is placed in W. If ‘d’ is ‘1’, the result is
placed in register ‘f’ (default).
If ‘a’ is ‘0’, the Access Bank is selected.
If ‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates
in Indexed Literal Offset Addressing
mode whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
Words:
1
Cycles:
1
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
register ‘f’
Process
Data
Write to
destination
REG, 1, 0
19h
0Dh
1
0011
Description:
Example:
SWAPF
Before Instruction
REG
=
After Instruction
REG
=
REG, 1, 0
53h
35h
; result is positive
SUBWFB REG, 0, 0
Before Instruction
REG
=
W
=
C
=
After Instruction
REG
=
W
=
C
=
Z
=
N
=
Example 3:
1Bh
1Ah
0
(0001 1011)
(0001 1010)
1Bh
00h
1
1
0
(0001 1011)
SUBWFB
Before Instruction
REG
=
W
=
C
=
After Instruction
REG
=
W
C
Z
N
Q3
Process
Data
Encoding:
=
=
=
=
DS39636A-page 294
; result is zero
REG, 1, 0
03h
0Eh
1
(0000 0011)
(0000 1101)
F5h
(1111 0100)
; [2’s comp]
(0000 1101)
0Eh
0
0
1
; result is negative
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
TBLRD
Table Read
TBLRD
Table Read (Continued)
Syntax:
TBLRD ( *; *+; *-; +*)
Example 1:
TBLRD
Operands:
None
Operation:
if TBLRD *,
(Prog Mem (TBLPTR)) → TABLAT;
TBLPTR – No Change;
if TBLRD *+,
(Prog Mem (TBLPTR)) → TABLAT;
(TBLPTR) + 1 → TBLPTR;
if TBLRD *-,
(Prog Mem (TBLPTR)) → TABLAT;
(TBLPTR) – 1 → TBLPTR;
if TBLRD +*,
(TBLPTR) + 1 → TBLPTR;
(Prog Mem (TBLPTR)) → TABLAT;
Before Instruction
TABLAT
TBLPTR
MEMORY (00A356h)
After Instruction
TABLAT
TBLPTR
Example 2:
0000
0000
0000
TBLRD
=
=
=
55h
00A356h
34h
=
=
34h
00A357h
+* ;
Before Instruction
TABLAT
TBLPTR
MEMORY (01A357h)
MEMORY (01A358h)
After Instruction
TABLAT
TBLPTR
Status Affected: None
Encoding:
*+ ;
=
=
=
=
AAh
01A357h
12h
34h
=
=
34h
01A358h
10nn
nn=0 *
=1 *+
=2 *=3 +*
Description:
This instruction is used to read the contents
of Program Memory (P.M.). To address the
program memory, a pointer called Table
Pointer (TBLPTR) is used.
The TBLPTR (a 21-bit pointer) points to
each byte in the program memory. TBLPTR
has a 2-Mbyte address range.
TBLPTR[0] = 0: Least Significant Byte
of Program Memory
Word
TBLPTR[0] = 1: Most Significant Byte
of Program Memory
Word
The TBLRD instruction can modify the value
of TBLPTR as follows:
• no change
• post-increment
• post-decrement
• pre-increment
Words:
1
Cycles:
2
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
No
operation
No
operation
No
operation
No
operation
No operation
(Read Program
Memory)
 2004 Microchip Technology Inc.
No
No operation
operation (Write TABLAT)
Preliminary
DS39636A-page 295
PIC18F2X1X/4X1X
TBLWT
Table Write
TBLWT
Table Write (Continued)
Syntax:
TBLWT ( *; *+; *-; +*)
Example 1:
TBLWT
Operands:
None
Operation:
if TBLWT*,
(TABLAT) → Holding Register;
TBLPTR – No Change;
if TBLWT*+,
(TABLAT) → Holding Register;
(TBLPTR) + 1 → TBLPTR;
if TBLWT*-,
(TABLAT) → Holding Register;
(TBLPTR) – 1 → TBLPTR;
if TBLWT+*,
(TBLPTR) + 1 → TBLPTR;
(TABLAT) → Holding Register;
Status Affected:
Example 2:
None
Encoding:
0000
0000
0000
*+;
Before Instruction
TABLAT
=
55h
TBLPTR
=
00A356h
HOLDING REGISTER
(00A356h)
=
FFh
After Instructions (table write completion)
TABLAT
=
55h
TBLPTR
=
00A357h
HOLDING REGISTER
(00A356h)
=
55h
11nn
nn=0 *
=1 *+
=2 *=3 +*
Description:
This instruction uses the 3 LSBs of
TBLPTR to determine which of the
8 holding registers the TABLAT is written
to. The holding registers are used to
program the contents of Program
Memory (P.M.). (Refer to Section 6.0
“Flash Program Memory” for additional
details on programming Flash memory.)
The TBLPTR (a 21-bit pointer) points to
each byte in the program memory.
TBLPTR has a 2-MByte address range.
The LSb of the TBLPTR selects which
byte of the program memory location to
access.
TBLPTR[0] = 0: Least Significant
Byte of Program
Memory Word
TBLPTR[0] = 1: Most Significant
Byte of Program
Memory Word
The TBLWT instruction can modify the
value of TBLPTR as follows:
• no change
• post-increment
• post-decrement
• pre-increment
Words:
1
Cycles:
2
TBLWT
+*;
Before Instruction
TABLAT
=
34h
TBLPTR
=
01389Ah
HOLDING REGISTER
(01389Ah)
=
FFh
HOLDING REGISTER
(01389Bh)
=
FFh
After Instruction (table write completion)
TABLAT
=
34h
TBLPTR
=
01389Bh
HOLDING REGISTER
(01389Ah)
=
FFh
HOLDING REGISTER
(01389Bh)
=
34h
Q Cycle Activity:
Q1
Decode
Q2
Q3
Q4
No
No
No
operation operation operation
No
No
No
No
operation operation operation operation
(Write to
(Read
Holding
TABLAT)
Register )
DS39636A-page 296
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
TSTFSZ
Test f, Skip if 0
XORLW
Exclusive OR Literal with W
Syntax:
TSTFSZ f {,a}
Syntax:
XORLW k
Operands:
0 ≤ f ≤ 255
a ∈ [0,1]
Operands:
0 ≤ k ≤ 255
Operation:
(W) .XOR. k → W
Status Affected:
N, Z
Operation:
skip if f = 0
Status Affected:
None
Encoding:
Encoding:
0110
Description:
011a
ffff
ffff
If ‘f’ = 0, the next instruction fetched
during the current instruction execution
is discarded and a NOP is executed,
making this a two-cycle instruction.
If ‘a’ is ‘0’, the Access Bank is selected.
If ‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates
in Indexed Literal Offset Addressing
mode whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
Words:
1
Cycles:
1(2)
Note: 3 cycles if skip and followed
by a 2-word instruction.
0000
1010
kkkk
kkkk
Description:
The contents of W are XORed with
the 8-bit literal ‘k’. The result is placed
in W.
Words:
1
Cycles:
1
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
literal ‘k’
Process
Data
Write to W
Example:
XORLW
0AFh
Before Instruction
W
=
After Instruction
W
=
B5h
1Ah
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
register ‘f’
Process
Data
No
operation
If skip:
Q1
Q2
Q3
Q4
No
operation
No
operation
No
operation
No
operation
If skip and followed by 2-word instruction:
Q1
Q2
Q3
Q4
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
No
operation
Example:
HERE
NZERO
ZERO
Before Instruction
PC
After Instruction
If CNT
PC
If CNT
PC
TSTFSZ
:
:
CNT, 1
=
Address (HERE)
=
=
≠
=
00h,
Address (ZERO)
00h,
Address (NZERO)
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 297
PIC18F2X1X/4X1X
XORWF
Exclusive OR W with f
Syntax:
XORWF
Operands:
0 ≤ f ≤ 255
d ∈ [0,1]
a ∈ [0,1]
Operation:
(W) .XOR. (f) → dest
Status Affected:
N, Z
Encoding:
0001
f {,d {,a}}
10da
ffff
ffff
Description:
Exclusive OR the contents of W with
register ‘f’. If ‘d’ is ‘0’, the result is stored
in W. If ‘d’ is ‘1’, the result is stored back
in the register ‘f’ (default).
If ‘a’ is ‘0’, the Access Bank is selected.
If ‘a’ is ‘1’, the BSR is used to select the
GPR bank (default).
If ‘a’ is ‘0’ and the extended instruction
set is enabled, this instruction operates
in Indexed Literal Offset Addressing
mode whenever f ≤ 95 (5Fh). See
Section 23.2.3 “Byte-Oriented and
Bit-Oriented Instructions in Indexed
Literal Offset Mode” for details.
Words:
1
Cycles:
1
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
register ‘f’
Process
Data
Write to
destination
Example:
XORWF
Before Instruction
REG
=
W
=
After Instruction
REG
=
W
=
DS39636A-page 298
REG, 1, 0
AFh
B5h
1Ah
B5h
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
23.2
Extended Instruction Set
A summary of the instructions in the extended instruction set is provided in Table 23-3. Detailed descriptions
are provided in Section 23.2.2 “Extended Instruction
Set”. The opcode field descriptions in Table 23-1
(page 258) apply to both the standard and extended
PIC18 instruction sets.
In addition to the standard 75 instructions of the PIC18
instruction set, PIC18F2X1X/4X1X devices also
provide an optional extension to the core CPU functionality. The added features include eight additional
instructions that augment indirect and indexed
addressing operations and the implementation of
Indexed Literal Offset Addressing mode for many of the
standard PIC18 instructions.
Note:
The additional features of the extended instruction set
are disabled by default. To enable them, users must set
the XINST configuration bit.
The instructions in the extended set (with the exception
of CALLW, MOVSF and MOVSS) can all be classified as
literal operations, which either manipulate the File
Select Registers, or use them for indexed addressing.
Two of the instructions, ADDFSR and SUBFSR, each
have an additional special instantiation for using FSR2.
These versions (ADDULNK and SUBULNK) allow for
automatic return after execution.
23.2.1
EXTENDED INSTRUCTION SYNTAX
Most of the extended instructions use indexed
arguments, using one of the File Select Registers and
some offset to specify a source or destination register.
When an argument for an instruction serves as part of
indexed addressing, it is enclosed in square brackets
(“[ ]”). This is done to indicate that the argument is used
as an index or offset. The MPASM™ Assembler will
flag an error if it determines that an index or offset value
is not bracketed.
The extended instructions are specifically implemented
to optimize re-entrant program code (that is, code that
is recursive or that uses a software stack) written in
high-level languages, particularly C. Among other
things, they allow users working in high-level
languages to perform certain operations on data
structures more efficiently. These include:
When the extended instruction set is enabled, brackets
are also used to indicate index arguments in byteoriented and bit-oriented instructions. This is in addition
to other changes in their syntax. For more details, see
Section 23.2.3.1 “Extended Instruction Syntax with
Standard PIC18 Commands”.
• dynamic allocation and deallocation of software
stack space when entering and leaving
subroutines
• function pointer invocation
• software Stack Pointer manipulation
• manipulation of variables located in a software
stack
TABLE 23-3:
The instruction set extension and the
Indexed Literal Offset Addressing mode
were designed for optimizing applications
written in C. The user may likely never use
these instructions directly in assembler.
The syntax for these commands is provided as a reference for users who may be
reviewing code that has been generated
by a compiler.
Note:
In the past, square brackets have been
used to denote optional arguments in the
PIC18 and earlier instruction sets. In this
text and going forward, optional
arguments are denoted by braces (“{ }”).
EXTENSIONS TO THE PIC18 INSTRUCTION SET
16-Bit Instruction Word
Mnemonic,
Operands
ADDFSR
ADDULNK
CALLW
MOVSF
f, k
k
MOVSS
zs, zd
PUSHL
k
SUBFSR
SUBULNK
f, k
k
zs, fd
Description
Cycles
MSb
Add literal to FSR
Add literal to FSR2 and return
Call subroutine using WREG
Move zs (source) to 1st word
fd (destination) 2nd word
Move zs (source) to 1st word
zd (destination) 2nd word
Store literal at FSR2,
decrement FSR2
Subtract literal from FSR
Subtract literal from FSR2 and
return
 2004 Microchip Technology Inc.
1
2
2
2
LSb
Status
Affected
1000
1000
0000
1011
ffff
1011
xxxx
1010
ffkk
11kk
0001
0zzz
ffff
1zzz
xzzz
kkkk
kkkk
kkkk
0100
zzzz
ffff
zzzz
zzzz
kkkk
None
None
None
None
1
1110
1110
0000
1110
1111
1110
1111
1110
1
2
1110
1110
1001
1001
ffkk
11kk
kkkk
kkkk
None
None
2
Preliminary
None
None
DS39636A-page 299
PIC18F2X1X/4X1X
23.2.2
EXTENDED INSTRUCTION SET
ADDFSR
Add Literal to FSR
ADDULNK
Syntax:
ADDFSR f, k
Syntax:
ADDULNK k
Operands:
0 ≤ k ≤ 63
f ∈ [ 0, 1, 2 ]
Operands:
0 ≤ k ≤ 63
Operation:
FSR(f) + k → FSR(f)
Status Affected:
None
Encoding:
1110
Add Literal to FSR2 and Return
FSR2 + k → FSR2,
Operation:
(TOS) → PC
Status Affected:
1000
ffkk
kkkk
Description:
The 6-bit literal ‘k’ is added to the
contents of the FSR specified by ‘f’.
Words:
1
Cycles:
1
None
Encoding:
1110
Q1
Q2
Q3
Q4
Read
literal ‘k’
Process
Data
Write to
FSR
Example:
ADDFSR
Before Instruction
FSR2
=
03FFh
After Instruction
FSR2
=
0422h
2, 23h
kkkk
Words:
1
Cycles:
2
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
literal ‘k’
Process
Data
Write to
FSR
No
Operation
No
Operation
No
Operation
No
Operation
Example:
Note:
11kk
The 6-bit literal ‘k’ is added to the
contents of FSR2. A RETURN is then
executed by loading the PC with the
TOS.
The instruction takes two cycles to
execute; a NOP is performed during
the second cycle.
This may be thought of as a special
case of the ADDFSR instruction,
where f = 3 (binary ‘11’); it operates
only on FSR2.
Q Cycle Activity:
Decode
1000
Description:
ADDULNK 23h
Before Instruction
FSR2
=
PC
=
03FFh
0100h
After Instruction
FSR2
=
PC
=
0422h
(TOS)
All PIC18 instructions may take an optional label argument preceding the instruction mnemonic for use in
symbolic addressing. If a label is used, the instruction syntax then becomes: {label} instruction argument(s).
DS39636A-page 300
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
CALLW
Subroutine Call Using WREG
MOVSF
Syntax:
CALLW
Syntax:
MOVSF [zs], fd
Operands:
None
Operands:
Operation:
(PC + 2) → TOS,
(W) → PCL,
(PCLATH) → PCH,
(PCLATU) → PCU
0 ≤ zs ≤ 127
0 ≤ fd ≤ 4095
Operation:
((FSR2) + zs) → fd
Status Affected:
None
Status Affected:
None
Encoding:
0000
0000
0001
0100
Description
First, the return address (PC + 2) is
pushed onto the return stack. Next, the
contents of W are written to PCL; the
existing value is discarded. Then the
contents of PCLATH and PCLATU are
latched into PCH and PCU,
respectively. The second cycle is
executed as a NOP instruction while the
new next instruction is fetched.
Unlike CALL, there is no option to
update W, Status or BSR.
Words:
1
Cycles:
2
Move Indexed to f
Encoding:
1st word (source)
2nd word (destin.)
Q1
Q2
Q3
Q4
Read
WREG
Push PC to
stack
No
operation
No
operation
No
operation
No
operation
No
operation
HERE
Before Instruction
PC
=
PCLATH =
PCLATU =
W
=
After Instruction
PC
=
TOS
=
PCLATH =
PCLATU =
W
=
2
Cycles:
2
Q Cycle Activity:
Q1
Decode
address (HERE)
10h
00h
06h
 2004 Microchip Technology Inc.
zzzzs
ffffd
Words:
CALLW
001006h
address (HERE + 2)
10h
00h
06h
0zzz
ffff
The contents of the source register are
moved to destination register ‘fd’. The
actual address of the source register is
determined by adding the 7-bit literal
offset ‘zs’ in the first word to the value of
FSR2. The address of the destination
register is specified by the 12-bit literal
‘fd’ in the second word. Both addresses
can be anywhere in the 4096-byte data
space (000h to FFFh).
The MOVSF instruction cannot use the
PCL, TOSU, TOSH or TOSL as the
destination register.
If the resultant source address points to
an indirect addressing register, the
value returned will be 00h.
Decode
Example:
1011
ffff
Description:
Q Cycle Activity:
Decode
1110
1111
Q2
Q3
Determine
Determine
source addr source addr
No
operation
No
operation
No dummy
read
Example:
MOVSF
Before Instruction
FSR2
Contents
of 85h
REG2
After Instruction
FSR2
Contents
of 85h
REG2
Preliminary
Q4
Read
source reg
Write
register ‘f’
(dest)
[05h], REG2
=
80h
=
=
33h
11h
=
80h
=
=
33h
33h
DS39636A-page 301
PIC18F2X1X/4X1X
MOVSS
Move Indexed to Indexed
PUSHL
Syntax:
Syntax:
PUSHL k
Operands:
MOVSS [zs], [zd]
0 ≤ zs ≤ 127
0 ≤ zd ≤ 127
Operands:
0 ≤ k ≤ 255
Operation:
((FSR2) + zs) → ((FSR2) + zd)
Operation:
k → (FSR2),
FSR2 – 1 → FSR2
Status Affected:
None
Status Affected:
None
Encoding:
1st word (source)
2nd word (dest.)
1110
1111
Description
1011
xxxx
1zzz
xzzz
zzzzs
zzzzd
The contents of the source register are
moved to the destination register. The
addresses of the source and destination
registers are determined by adding the
7-bit literal offsets ‘zs’ or ‘zd’,
respectively, to the value of FSR2. Both
registers can be located anywhere in
the 4096-byte data memory space
(000h to FFFh).
The MOVSS instruction cannot use the
PCL, TOSU, TOSH or TOSL as the
destination register.
If the resultant source address points to
an indirect addressing register, the
value returned will be 00h. If the
resultant destination address points to
an indirect addressing register, the
instruction will execute as a NOP.
Words:
2
Cycles:
2
Store Literal at FSR2, Decrement FSR2
Encoding:
1111
1010
kkkk
kkkk
Description:
The 8-bit literal ‘k’ is written to the data
memory address specified by FSR2. FSR2
is decremented by 1 after the operation.
This instruction allows users to push values
onto a software stack.
Words:
1
Cycles:
1
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read ‘k’
Process
data
Write to
destination
Example:
PUSHL
08h
Before Instruction
FSR2H:FSR2L
Memory (01ECh)
=
=
01ECh
00h
After Instruction
FSR2H:FSR2L
Memory (01ECh)
=
=
01EBh
08h
Q Cycle Activity:
Q1
Decode
Decode
Q2
Q3
Determine
Determine
source addr source addr
Determine
dest addr
Example:
MOVSS
Before Instruction
FSR2
Contents
of 85h
Contents
of 86h
After Instruction
FSR2
Contents
of 85h
Contents
of 86h
DS39636A-page 302
Determine
dest addr
Q4
Read
source reg
Write
to dest reg
[05h], [06h]
=
80h
=
33h
=
11h
=
80h
=
33h
=
33h
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
SUBFSR
Subtract Literal from FSR
SUBULNK
Syntax:
SUBFSR f, k
Syntax:
SUBULNK k
Operands:
0 ≤ k ≤ 63
Operands:
0 ≤ k ≤ 63
f ∈ [ 0, 1, 2 ]
Operation:
Operation:
FSR(f) – k → FSRf
Status Affected:
None
Encoding:
1110
FSR2 – k → FSR2
(TOS) → PC
Status Affected: None
1001
ffkk
kkkk
Description:
The 6-bit literal ‘k’ is subtracted from
the contents of the FSR specified by
‘f’.
Words:
1
Cycles:
1
Encoding:
1110
Q1
Q2
Q3
Q4
Decode
Read
register ‘f’
Process
Data
Write to
destination
SUBFSR 2, 23h
1001
11kk
kkkk
Description:
The 6-bit literal ‘k’ is subtracted from the
contents of the FSR2. A RETURN is then
executed by loading the PC with the TOS.
The instruction takes two cycles to
execute; a NOP is performed during the
second cycle.
This may be thought of as a special case of
the SUBFSR instruction, where f = 3 (binary
‘11’); it operates only on FSR2.
Words:
1
Cycles:
2
Q Cycle Activity:
Example:
Subtract Literal from FSR2 and Return
Q Cycle Activity:
Before Instruction
FSR2
=
Q1
Q2
Q3
Q4
03FFh
Decode
After Instruction
FSR2
=
Read
register ‘f’
Process
Data
Write to
destination
03DCh
No
Operation
No
Operation
No
Operation
No
Operation
Example:
 2004 Microchip Technology Inc.
Preliminary
SUBULNK 23h
Before Instruction
FSR2
=
PC
=
03FFh
0100h
After Instruction
FSR2
=
PC
=
03DCh
(TOS)
DS39636A-page 303
PIC18F2X1X/4X1X
23.2.3
Note:
BYTE-ORIENTED AND
BIT-ORIENTED INSTRUCTIONS IN
INDEXED LITERAL OFFSET MODE
Enabling the PIC18 instruction set
extension may cause legacy applications
to behave erratically or fail entirely.
In addition to eight new commands in the extended set,
enabling the extended instruction set also enables
Indexed Literal Offset Addressing mode (Section 5.5.1
“Indexed Addressing with Literal Offset”). This has
a significant impact on the way that many commands of
the standard PIC18 instruction set are interpreted.
When the extended set is disabled, addresses embedded in opcodes are treated as literal memory locations:
either as a location in the Access Bank (‘a’ = 0) or in a
GPR bank designated by the BSR (‘a’ = 1). When the
extended instruction set is enabled and ‘a’ = 0,
however, a file register argument of 5Fh or less is
interpreted as an offset from the pointer value in FSR2
and not as a literal address. For practical purposes, this
means that all instructions that use the Access RAM bit
as an argument – that is, all byte-oriented and bitoriented instructions, or almost half of the core PIC18
instructions – may behave differently when the
extended instruction set is enabled.
When the content of FSR2 is 00h, the boundaries of the
Access RAM are essentially remapped to their original
values. This may be useful in creating backward
compatible code. If this technique is used, it may be
necessary to save the value of FSR2 and restore it
when moving back and forth between C and assembly
routines in order to preserve the Stack Pointer. Users
must also keep in mind the syntax requirements of the
extended instruction set (see Section 23.2.3.1
“Extended Instruction Syntax with Standard PIC18
Commands”).
23.2.3.1
Extended Instruction Syntax with
Standard PIC18 Commands
When the extended instruction set is enabled, the file
register argument, ‘f’, in the standard byte-oriented and
bit-oriented commands is replaced with the literal offset
value, ‘k’. As already noted, this occurs only when ‘f’ is
less than or equal to 5Fh. When an offset value is used,
it must be indicated by square brackets (“[ ]”). As with
the extended instructions, the use of brackets indicates
to the compiler that the value is to be interpreted as an
index or an offset. Omitting the brackets, or using a
value greater than 5Fh within brackets, will generate an
error in the MPASM Assembler.
If the index argument is properly bracketed for Indexed
Literal Offset Addressing, the Access RAM argument is
never specified; it will automatically be assumed to be
‘0’. This is in contrast to standard operation (extended
instruction set disabled) when ‘a’ is set on the basis of
the target address. Declaring the Access RAM bit in
this mode will also generate an error in the MPASM
Assembler.
The destination argument, ‘d’, functions as before.
In the latest versions of the MPASM Assembler,
language support for the extended instruction set must
be explicitly invoked. This is done with either the
command line option, /y, or the PE directive in the
source listing.
23.2.4
CONSIDERATIONS WHEN
ENABLING THE EXTENDED
INSTRUCTION SET
It is important to note that the extensions to the instruction set may not be beneficial to all users. In particular,
users who are not writing code that uses a software
stack may not benefit from using the extensions to the
instruction set.
Although the Indexed Literal Offset Addressing mode
can be very useful for dynamic stack and pointer
manipulation, it can also be very annoying if a simple
arithmetic operation is carried out on the wrong
register. Users who are accustomed to the PIC18
programming must keep in mind that when the
extended instruction set is enabled, register addresses
of 5Fh or less are used for Indexed Literal Offset
Addressing.
Additionally, the Indexed Literal Offset Addressing
mode may create issues with legacy applications
written to the PIC18 assembler. This is because
instructions in the legacy code may attempt to address
registers in the Access Bank below 5Fh. Since these
addresses are interpreted as literal offsets to FSR2
when the instruction set extension is enabled, the
application may read or write to the wrong data
addresses.
Representative examples of typical byte-oriented and
bit-oriented instructions in the Indexed Literal Offset
Addressing mode are provided on the following page to
show how execution is affected. The operand conditions shown in the examples are applicable to all
instructions of these types.
When porting an application to the PIC18F2X1X/4X1X,
it is very important to consider the type of code. A large,
re-entrant application that is written in ‘C’ and would
benefit from efficient compilation will do well when
using the instruction set extensions. Legacy applications that heavily use the Access Bank will most likely
not benefit from using the extended instruction set.
DS39636A-page 304
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
ADDWF
Add W to Indexed
(Indexed Literal Offset mode)
BSF
Bit Set Indexed
(Indexed Literal Offset mode)
Syntax:
ADDWF
Syntax:
BSF [k], b
Operands:
0 ≤ k ≤ 95
d ∈ [0,1]
Operands:
0 ≤ f ≤ 95
0≤b≤7
Operation:
(W) + ((FSR2) + k) → dest
Operation:
1 → ((FSR2) + k)<b>
Status Affected:
N, OV, C, DC, Z
Status Affected:
None
Encoding:
[k] {,d}
0010
Description:
01d0
kkkk
kkkk
The contents of W are added to the
contents of the register indicated by
FSR2, offset by the value ‘k’.
If ‘d’ is ‘0’, the result is stored in W. If ‘d’
is ‘1’, the result is stored back in
register ‘f’ (default).
Encoding:
1000
bbb0
kkkk
kkkk
Description:
Bit ‘b’ of the register indicated by FSR2,
offset by the value ‘k’, is set.
Words:
1
Cycles:
1
Q Cycle Activity:
Words:
1
Q1
Q2
Q3
Q4
Cycles:
1
Decode
Read
register ‘f’
Process
Data
Write to
destination
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read ‘k’
Process
Data
Write to
destination
Example:
ADDWF
Example:
Before Instruction
FLAG_OFST
FSR2
Contents
of 0A0Ah
After Instruction
Contents
of 0A0Ah
[OFST] ,0
Before Instruction
W
OFST
FSR2
Contents
of 0A2Ch
After Instruction
W
Contents
of 0A2Ch
=
=
=
17h
2Ch
0A00h
=
20h
=
37h
=
20h
BSF
[FLAG_OFST], 7
=
=
0Ah
0A00h
=
55h
=
D5h
Set Indexed
(Indexed Literal Offset mode)
SETF
Syntax:
SETF [k]
Operands:
0 ≤ k ≤ 95
Operation:
FFh → ((FSR2) + k)
Status Affected:
None
Encoding:
0110
1000
kkkk
kkkk
Description:
The contents of the register indicated by
FSR2, offset by ‘k’, are set to FFh.
Words:
1
Cycles:
1
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read ‘k’
Process
Data
Write
register
Example:
SETF
Before Instruction
OFST
FSR2
Contents
of 0A2Ch
After Instruction
Contents
of 0A2Ch
 2004 Microchip Technology Inc.
Preliminary
[OFST]
=
=
2Ch
0A00h
=
00h
=
FFh
DS39636A-page 305
PIC18F2X1X/4X1X
23.2.5
SPECIAL CONSIDERATIONS WITH
MICROCHIP MPLAB® IDE TOOLS
The latest versions of Microchip’s software tools have
been designed to fully support the extended instruction
set of the PIC18F2X1X/4X1X family of devices. This
includes the MPLAB C18 C compiler, MPASM
assembly
language
and
MPLAB
Integrated
Development Environment (IDE).
When selecting a target device for software
development, MPLAB IDE will automatically set default
configuration bits for that device. The default setting for
the XINST configuration bit is ‘0’, disabling the
extended instruction set and Indexed Literal Offset
Addressing mode. For proper execution of applications
developed to take advantage of the extended
instruction set, XINST must be set during
programming.
DS39636A-page 306
To develop software for the extended instruction set,
the user must enable support for the instructions and
the Indexed Addressing mode in their language tool(s).
Depending on the environment being used, this may be
done in several ways:
• A menu option, or dialog box within the
environment, that allows the user to configure the
language tool and its settings for the project
• A command line option
• A directive in the source code
These options vary between different compilers,
assemblers and development environments. Users are
encouraged to review the documentation accompanying their development systems for the appropriate
information.
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
24.0
DEVELOPMENT SUPPORT
24.1
The PICmicro® microcontrollers are supported with a
full range of hardware and software development tools:
• Integrated Development Environment
- MPLAB® IDE Software
• Assemblers/Compilers/Linkers
- MPASMTM Assembler
- MPLAB C17 and MPLAB C18 C Compilers
- MPLINKTM Object Linker/
MPLIBTM Object Librarian
- MPLAB C30 C Compiler
- MPLAB ASM30 Assembler/Linker/Library
• Simulators
- MPLAB SIM Software Simulator
- MPLAB dsPIC30 Software Simulator
• Emulators
- MPLAB ICE 2000 In-Circuit Emulator
- MPLAB ICE 4000 In-Circuit Emulator
• In-Circuit Debugger
- MPLAB ICD 2
• Device Programmers
- PRO MATE® II Universal Device Programmer
- PICSTART® Plus Development Programmer
- MPLAB PM3 Device Programmer
• Low-Cost Demonstration Boards
- PICDEMTM 1 Demonstration Board
- PICDEM.netTM Demonstration Board
- PICDEM 2 Plus Demonstration Board
- PICDEM 3 Demonstration Board
- PICDEM 4 Demonstration Board
- PICDEM 17 Demonstration Board
- PICDEM 18R Demonstration Board
- PICDEM LIN Demonstration Board
- PICDEM USB Demonstration Board
• Evaluation Kits
- KEELOQ® Evaluation and Programming Tools
- PICDEM MSC
- microID® Developer Kits
- CAN
- PowerSmart® Developer Kits
- Analog
MPLAB Integrated Development
Environment Software
The MPLAB IDE software brings an ease of software
development previously unseen in the 8/16-bit microcontroller market. The MPLAB IDE is a Windows®
based application that contains:
• An interface to debugging tools
- simulator
- programmer (sold separately)
- emulator (sold separately)
- in-circuit debugger (sold separately)
• A full-featured editor with color coded context
• A multiple project manager
• Customizable data windows with direct edit of
contents
• High-level source code debugging
• Mouse over variable inspection
• Extensive on-line help
The MPLAB IDE allows you to:
• Edit your source files (either assembly or C)
• One touch assemble (or compile) and download
to PICmicro emulator and simulator tools
(automatically updates all project information)
• Debug using:
- source files (assembly or C)
- mixed assembly and C
- machine code
MPLAB IDE supports multiple debugging tools in a
single development paradigm, from the cost effective
simulators, through low-cost in-circuit debuggers, to
full-featured emulators. This eliminates the learning
curve when upgrading to tools with increasing flexibility
and power.
24.2
MPASM Assembler
The MPASM assembler is a full-featured, universal
macro assembler for all PICmicro MCUs.
The MPASM assembler generates relocatable object
files for the MPLINK object linker, Intel® standard HEX
files, MAP files to detail memory usage and symbol reference, absolute LST files that contain source lines and
generated machine code and COFF files for
debugging.
The MPASM assembler features include:
• Integration into MPLAB IDE projects
• User defined macros to streamline assembly code
• Conditional assembly for multi-purpose source
files
• Directives that allow complete control over the
assembly process
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 307
PIC18F2X1X/4X1X
24.3
MPLAB C17 and MPLAB C18
C Compilers
24.6
The MPLAB C17 and MPLAB C18 Code Development
Systems are complete ANSI C compilers for
Microchip’s PIC17CXXX and PIC18CXXX family of
microcontrollers. These compilers provide powerful
integration capabilities, superior code optimization and
ease of use not found with other compilers.
For easy source level debugging, the compilers provide
symbol information that is optimized to the MPLAB IDE
debugger.
24.4
MPLINK Object Linker/
MPLIB Object Librarian
The MPLINK object linker combines relocatable
objects created by the MPASM assembler and the
MPLAB C17 and MPLAB C18 C compilers. It can link
relocatable objects from precompiled libraries, using
directives from a linker script.
The MPLIB object librarian manages the creation and
modification of library files of precompiled code. When
a routine from a library is called from a source file, only
the modules that contain that routine will be linked in
with the application. This allows large libraries to be
used efficiently in many different applications.
The object linker/library features include:
• Efficient linking of single libraries instead of many
smaller files
• Enhanced code maintainability by grouping
related modules together
• Flexible creation of libraries with easy module
listing, replacement, deletion and extraction
24.5
MPLAB C30 C Compiler
MPLAB C30 is distributed with a complete ANSI C
standard library. All library functions have been validated and conform to the ANSI C library standard. The
library includes functions for string manipulation,
dynamic memory allocation, data conversion, timekeeping and math functions (trigonometric, exponential
and hyperbolic). The compiler provides symbolic
information for high-level source debugging with the
MPLAB IDE.
DS39636A-page 308
MPLAB ASM30 assembler produces relocatable
machine code from symbolic assembly language for
dsPIC30F devices. MPLAB C30 compiler uses the
assembler to produce it’s object file. The assembler
generates relocatable object files that can then be
archived or linked with other relocatable object files and
archives to create an executable file. Notable features
of the assembler include:
•
•
•
•
•
•
Support for the entire dsPIC30F instruction set
Support for fixed-point and floating-point data
Command line interface
Rich directive set
Flexible macro language
MPLAB IDE compatibility
24.7
MPLAB SIM Software Simulator
The MPLAB SIM software simulator allows code development in a PC hosted environment by simulating the
PICmicro series microcontrollers on an instruction
level. On any given instruction, the data areas can be
examined or modified and stimuli can be applied from
a file, or user defined key press, to any pin. The execution can be performed in Single-Step, Execute Until
Break or Trace mode.
The MPLAB SIM simulator fully supports symbolic
debugging using the MPLAB C17 and MPLAB C18
C Compilers, as well as the MPASM assembler. The
software simulator offers the flexibility to develop and
debug code outside of the laboratory environment,
making it an excellent, economical software
development tool.
24.8
The MPLAB C30 C compiler is a full-featured, ANSI
compliant, optimizing compiler that translates standard
ANSI C programs into dsPIC30F assembly language
source. The compiler also supports many command
line options and language extensions to take full
advantage of the dsPIC30F device hardware capabilities and afford fine control of the compiler code
generator.
MPLAB ASM30 Assembler, Linker
and Librarian
MPLAB SIM30 Software Simulator
The MPLAB SIM30 software simulator allows code
development in a PC hosted environment by simulating
the dsPIC30F series microcontrollers on an instruction
level. On any given instruction, the data areas can be
examined or modified and stimuli can be applied from
a file, or user defined key press, to any of the pins.
The MPLAB SIM30 simulator fully supports symbolic
debugging using the MPLAB C30 C Compiler and
MPLAB ASM30 assembler. The simulator runs in either
a Command Line mode for automated tasks, or from
MPLAB IDE. This high-speed simulator is designed to
debug, analyze and optimize time intensive DSP
routines.
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
24.9
MPLAB ICE 2000
High-Performance Universal
In-Circuit Emulator
24.11 MPLAB ICD 2 In-Circuit Debugger
The MPLAB ICE 2000 universal in-circuit emulator is
intended to provide the product development engineer
with a complete microcontroller design tool set for
PICmicro microcontrollers. Software control of the
MPLAB ICE 2000 in-circuit emulator is advanced by
the MPLAB Integrated Development Environment,
which allows editing, building, downloading and source
debugging from a single environment.
The MPLAB ICE 2000 is a full-featured emulator system with enhanced trace, trigger and data monitoring
features. Interchangeable processor modules allow the
system to be easily reconfigured for emulation of different processors. The universal architecture of the
MPLAB ICE in-circuit emulator allows expansion to
support new PICmicro microcontrollers.
The MPLAB ICE 2000 in-circuit emulator system has
been designed as a real-time emulation system with
advanced features that are typically found on more
expensive development tools. The PC platform and
Microsoft® Windows 32-bit operating system were
chosen to best make these features available in a
simple, unified application.
24.10 MPLAB ICE 4000
High-Performance Universal
In-Circuit Emulator
The MPLAB ICE 4000 universal in-circuit emulator is
intended to provide the product development engineer
with a complete microcontroller design tool set for highend PICmicro microcontrollers. Software control of the
MPLAB ICE in-circuit emulator is provided by the
MPLAB Integrated Development Environment, which
allows editing, building, downloading and source
debugging from a single environment.
The MPLAB ICD 4000 is a premium emulator system,
providing the features of MPLAB ICE 2000, but with
increased emulation memory and high-speed performance for dsPIC30F and PIC18XXXX devices. Its
advanced emulator features include complex triggering
and timing, up to 2 Mb of emulation memory and the
ability to view variables in real-time.
The MPLAB ICE 4000 in-circuit emulator system has
been designed as a real-time emulation system with
advanced features that are typically found on more
expensive development tools. The PC platform and
Microsoft Windows 32-bit operating system were
chosen to best make these features available in a
simple, unified application.
 2004 Microchip Technology Inc.
Microchip’s In-Circuit Debugger, MPLAB ICD 2, is a
powerful, low-cost, run-time development tool,
connecting to the host PC via an RS-232 or high-speed
USB interface. This tool is based on the Flash
PICmicro MCUs and can be used to develop for these
and other PICmicro microcontrollers. The MPLAB
ICD 2 utilizes the in-circuit debugging capability built
into the Flash devices. This feature, along with
Microchip’s In-Circuit Serial ProgrammingTM (ICSPTM)
protocol, offers cost effective in-circuit Flash debugging
from the graphical user interface of the MPLAB
Integrated Development Environment. This enables a
designer to develop and debug source code by setting
breakpoints, single-stepping and watching variables,
CPU status and peripheral registers. Running at full
speed enables testing hardware and applications in
real-time. MPLAB ICD 2 also serves as a development
programmer for selected PICmicro devices.
24.12 PRO MATE II Universal Device
Programmer
The PRO MATE II is a universal, CE compliant device
programmer with programmable voltage verification at
VDDMIN and VDDMAX for maximum reliability. It features
an LCD display for instructions and error messages
and a modular detachable socket assembly to support
various package types. In Stand-Alone mode, the
PRO MATE II device programmer can read, verify and
program PICmicro devices without a PC connection. It
can also set code protection in this mode.
24.13 MPLAB PM3 Device Programmer
The MPLAB PM3 is a universal, CE compliant device
programmer with programmable voltage verification at
VDDMIN and VDDMAX for maximum reliability. It features
a large LCD display (128 x 64) for menus and error
messages and a modular detachable socket assembly
to support various package types. The ICSP™ cable
assembly is included as a standard item. In StandAlone mode, the MPLAB PM3 device programmer can
read, verify and program PICmicro devices without a
PC connection. It can also set code protection in this
mode. MPLAB PM3 connects to the host PC via an RS232 or USB cable. MPLAB PM3 has high-speed communications and optimized algorithms for quick programming of large memory devices and incorporates
an SD/MMC card for file storage and secure data applications.
Preliminary
DS39636A-page 309
PIC18F2X1X/4X1X
24.14 PICSTART Plus Development
Programmer
24.17 PICDEM 2 Plus
Demonstration Board
The PICSTART Plus development programmer is an
easy-to-use, low-cost, prototype programmer. It connects to the PC via a COM (RS-232) port. MPLAB
Integrated Development Environment software makes
using the programmer simple and efficient. The
PICSTART Plus development programmer supports
most PICmicro devices up to 40 pins. Larger pin count
devices, such as the PIC16C92X and PIC17C76X,
may be supported with an adapter socket. The
PICSTART Plus development programmer is CE
compliant.
The PICDEM 2 Plus demonstration board supports
many 18, 28 and 40-pin microcontrollers, including
PIC16F87X and PIC18FXX2 devices. All the necessary hardware and software is included to run the demonstration programs. The sample microcontrollers
provided with the PICDEM 2 demonstration board can
be programmed with a PRO MATE II device programmer, PICSTART Plus development programmer, or
MPLAB ICD 2 with a Universal Programmer Adapter.
The MPLAB ICD 2 and MPLAB ICE in-circuit emulators
may also be used with the PICDEM 2 demonstration
board to test firmware. A prototype area extends the
circuitry for additional application components. Some
of the features include an RS-232 interface, a 2 x 16
LCD display, a piezo speaker, an on-board temperature
sensor, four LEDs and sample PIC18F452 and
PIC16F877 Flash microcontrollers.
24.15 PICDEM 1 PICmicro
Demonstration Board
The PICDEM 1 demonstration board demonstrates the
capabilities of the PIC16C5X (PIC16C54 to
PIC16C58A), PIC16C61, PIC16C62X, PIC16C71,
PIC16C8X, PIC17C42, PIC17C43 and PIC17C44. All
necessary hardware and software is included to run
basic demo programs. The sample microcontrollers
provided with the PICDEM 1 demonstration board can
be programmed with a PRO MATE II device programmer or a PICSTART Plus development programmer.
The PICDEM 1 demonstration board can be connected
to the MPLAB ICE in-circuit emulator for testing. A
prototype area extends the circuitry for additional application components. Features include an RS-232
interface, a potentiometer for simulated analog input,
push button switches and eight LEDs.
24.16 PICDEM.net Internet/Ethernet
Demonstration Board
The PICDEM.net demonstration board is an Internet/
Ethernet demonstration board using the PIC18F452
microcontroller and TCP/IP firmware. The board
supports any 40-pin DIP device that conforms to the
standard pinout used by the PIC16F877 or
PIC18C452. This kit features a user friendly TCP/IP
stack, web server with HTML, a 24L256 Serial
EEPROM for Xmodem download to web pages into
Serial EEPROM, ICSP/MPLAB ICD 2 interface connector, an Ethernet interface, RS-232 interface and a
16 x 2 LCD display. Also included is the book and
CD-ROM “TCP/IP Lean, Web Servers for Embedded
Systems,” by Jeremy Bentham
DS39636A-page 310
24.18 PICDEM 3 PIC16C92X
Demonstration Board
The PICDEM 3 demonstration board supports the
PIC16C923 and PIC16C924 in the PLCC package. All
the necessary hardware and software is included to run
the demonstration programs.
24.19 PICDEM 4 8/14/18-Pin
Demonstration Board
The PICDEM 4 can be used to demonstrate the capabilities of the 8, 14 and 18-pin PIC16XXXX and
PIC18XXXX MCUs, including the PIC16F818/819,
PIC16F87/88, PIC16F62XA and the PIC18F1320
family of microcontrollers. PICDEM 4 is intended to
showcase the many features of these low pin count
parts, including LIN and Motor Control using ECCP.
Special provisions are made for low-power operation
with the supercapacitor circuit and jumpers allow onboard hardware to be disabled to eliminate current
draw in this mode. Included on the demo board are provisions for Crystal, RC or Canned Oscillator modes, a
five volt regulator for use with a nine volt wall adapter
or battery, DB-9 RS-232 interface, ICD connector for
programming via ICSP and development with MPLAB
ICD 2, 2 x 16 liquid crystal display, PCB footprints for
H-Bridge motor driver, LIN transceiver and EEPROM.
Also included are: header for expansion, eight LEDs,
four potentiometers, three push buttons and a prototyping area. Included with the kit is a PIC16F627A and
a PIC18F1320. Tutorial firmware is included along
with the User’s Guide.
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
24.20 PICDEM 17 Demonstration Board
The PICDEM 17 demonstration board is an evaluation
board that demonstrates the capabilities of several
Microchip microcontrollers, including PIC17C752,
PIC17C756A, PIC17C762 and PIC17C766. A programmed sample is included. The PRO MATE II device
programmer, or the PICSTART Plus development programmer, can be used to reprogram the device for user
tailored application development. The PICDEM 17
demonstration board supports program download and
execution from external on-board Flash memory. A
generous prototype area is available for user hardware
expansion.
24.21 PICDEM 18R PIC18C601/801
Demonstration Board
The PICDEM 18R demonstration board serves to assist
development of the PIC18C601/801 family of Microchip
microcontrollers. It provides hardware implementation
of both 8-bit Multiplexed/Demultiplexed and 16-bit
Memory modes. The board includes 2 Mb external
Flash memory and 128 Kb SRAM memory, as well as
serial EEPROM, allowing access to the wide range of
memory types supported by the PIC18C601/801.
24.22 PICDEM LIN PIC16C43X
Demonstration Board
The powerful LIN hardware and software kit includes a
series of boards and three PICmicro microcontrollers.
The small footprint PIC16C432 and PIC16C433 are
used as slaves in the LIN communication and feature
on-board LIN transceivers. A PIC16F874 Flash
microcontroller serves as the master. All three microcontrollers are programmed with firmware to provide
LIN bus communication.
24.24 PICDEM USB PIC16C7X5
Demonstration Board
The PICDEM USB Demonstration Board shows off the
capabilities of the PIC16C745 and PIC16C765 USB
microcontrollers. This board provides the basis for
future USB products.
24.25 Evaluation and
Programming Tools
In addition to the PICDEM series of circuits, Microchip
has a line of evaluation kits and demonstration software
for these products.
• KEELOQ evaluation and programming tools for
Microchip’s HCS Secure Data Products
• CAN developers kit for automotive network
applications
• Analog design boards and filter design software
• PowerSmart battery charging evaluation/
calibration kits
• IrDA® development kit
• microID development and rfLabTM development
software
• SEEVAL® designer kit for memory evaluation and
endurance calculations
• PICDEM MSC demo boards for Switching mode
power supply, high-power IR driver, delta sigma
ADC and flow rate sensor
Check the Microchip web page and the latest Product
Selector Guide for the complete list of demonstration
and evaluation kits.
24.23 PICkitTM 1 Flash Starter Kit
A complete “development system in a box”, the PICkit™
Flash Starter Kit includes a convenient multi-section
board for programming, evaluation and development of
8/14-pin Flash PIC® microcontrollers. Powered via USB,
the board operates under a simple Windows GUI. The
PICkit 1 Starter Kit includes the User’s Guide (on CD
ROM), PICkit 1 tutorial software and code for various
applications. Also included are MPLAB® IDE (Integrated
Development Environment) software, software and
hardware “Tips 'n Tricks for 8-pin Flash PIC®
Microcontrollers” Handbook and a USB interface cable.
Supports all current 8/14-pin Flash PIC microcontrollers,
as well as many future planned devices.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 311
PIC18F2X1X/4X1X
NOTES:
DS39636A-page 312
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
25.0
ELECTRICAL CHARACTERISTICS
Absolute Maximum Ratings(†)
Ambient temperature under bias.............................................................................................................-40°C to +125°C
Storage temperature .............................................................................................................................. -65°C to +150°C
Voltage on any pin with respect to VSS (except VDD and MCLR) ................................................... -0.3V to (VDD + 0.3V)
Voltage on VDD with respect to VSS ......................................................................................................... -0.3V to +7.5V
Voltage on MCLR with respect to VSS (Note 2) ......................................................................................... 0V to +13.25V
Total power dissipation (Note 1) ...............................................................................................................................1.0W
Maximum current out of VSS pin ...........................................................................................................................300 mA
Maximum current into VDD pin ..............................................................................................................................250 mA
Input clamp current, IIK (VI < 0 or VI > VDD)...................................................................................................................... ±20 mA
Output clamp current, IOK (VO < 0 or VO > VDD) .............................................................................................................. ±20 mA
Maximum output current sunk by any I/O pin..........................................................................................................25 mA
Maximum output current sourced by any I/O pin ....................................................................................................25 mA
Maximum current sunk by all ports .......................................................................................................................200 mA
Maximum current sourced by all ports ..................................................................................................................200 mA
Note 1: Power dissipation is calculated as follows:
Pdis = VDD x {IDD – ∑ IOH} + ∑ {(VDD – VOH) x IOH} + ∑(VOL x IOL)
2: Voltage spikes below VSS at the MCLR/VPP/RE3 pin, inducing currents greater than 80 mA, may cause
latch-up. Thus, a series resistor of 50-100Ω should be used when applying a “low” level to the MCLR/VPP/
RE3 pin, rather than pulling this pin directly to VSS.
† NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the
device. This is a stress rating only and functional operation of the device at those or any other conditions above those
indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for
extended periods may affect device reliability.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 313
PIC18F2X1X/4X1X
FIGURE 25-1:
PIC18F2X1X/4X1X VOLTAGE-FREQUENCY GRAPH (INDUSTRIAL)
6.0V
5.5V
Voltage
5.0V
PIC18F2X1X/4X1X
4.5V
4.2V
4.0V
3.5V
3.0V
2.5V
2.0V
40 MHz
Frequency
PIC18F2X1X/4X1X VOLTAGE-FREQUENCY GRAPH (EXTENDED)
FIGURE 25-2:
6.0V
5.5V
Voltage
5.0V
PIC18F2X1X/4X1X
4.5V
4.2V
4.0V
3.5V
3.0V
2.5V
2.0V
25 MHz
Frequency
DS39636A-page 314
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
FIGURE 25-3:
PIC18LF2X1X/4X1X VOLTAGE-FREQUENCY GRAPH (INDUSTRIAL)
6.0V
5.5V
Voltage
5.0V
PIC18LF2X1X/4X1X
4.5V
4.2V
4.0V
3.5V
3.0V
2.5V
2.0V
40 MHz
4 MHz
Frequency
FMAX = (16.36 MHz/V) (VDDAPPMIN – 2.0V) + 4 MHz
Note: VDDAPPMIN is the minimum voltage of the PICmicro® device in the application.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 315
PIC18F2X1X/4X1X
25.1
DC Characteristics:
Supply Voltage
PIC18F2X1X/4X1X (Industrial)
PIC18LF2X1X/4X1X (Industrial)
PIC18LF2X1X/4X1X
(Industrial)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
PIC18F2X1X/4X1X
(Industrial, Extended)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
-40°C ≤ TA ≤ +125°C for extended
Param
No.
D001
Symbol
VDD
D002
VDR
D003
VPOR
D004
SVDD
VBOR
D005
D005
Legend:
Note 1:
Characteristic
Min
Typ
Max Units
Conditions
Supply Voltage
PIC18LF2X1X/4X1X 2.0
PIC18F2X1X/4X1X 4.2
RAM Data Retention
1.5
Voltage(1)
VDD Start Voltage
—
to ensure internal
Power-on Reset signal
VDD Rise Rate
0.05
to ensure internal
Power-on Reset signal
Brown-out Reset Voltage
PIC18LF2X1X/4X1X
—
—
—
5.5
5.5
—
V
V
V
HS, XT, RC and LP Oscillator mode
—
0.7
V
See section on Power-on Reset for details
—
—
V/ms See section on Power-on Reset for details
BORV1:BORV0 = 11
NA
2.05 2.16
V
BORV1:BORV0 = 10
2.65 2.79 2.93
V
All devices
BORV1:BORV0 = 01
4.11 4.33 4.55
V
BORV1:BORV0 = 00
4.36 4.59 4.82
V
Shading of rows is to assist in readability of the table.
This is the limit to which VDD can be lowered in Sleep mode, or during a device Reset, without losing RAM data.
DS39636A-page 316
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
25.2
DC Characteristics:
Power-Down and Supply Current
PIC18F2X1X/4X1X (Industrial)
PIC18LF2X1X/4X1X (Industrial)
PIC18LF2X1X/4X1X
(Industrial)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
PIC18F2X1X/4X1X
(Industrial, Extended)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
-40°C ≤ TA ≤ +125°C for extended
ParamNo.
Device
Power-down Current (IPD)
Typ
Max
Units
Conditions
(1)
PIC18LF2X1X/4X1X
Legend:
Note 1:
2:
3:
4:
5:
0.1
950
nA
-40°C
VDD = 2.0V,
0.1
1.0
µA
+25°C
(Sleep mode)
0.2
5
µA
+85°C
PIC18LF2X1X/4X1X 0.1
1.4
µA
-40°C
VDD = 3.0V,
0.1
2
µA
+25°C
(Sleep mode)
0.3
8
µA
+85°C
All devices 0.1
1.9
µA
-40°C
0.1
2.0
µA
+25°C
VDD = 5.0V,
(Sleep mode)
0.4
15
µA
+85°C
Extended devices only 10
120
µA
+125°C
Shading of rows is to assist in readability of the table.
The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured
with the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD or VSS and all features that
add delta current disabled (such as WDT, Timer1 Oscillator, BOR, etc.).
The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin
loading and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have
an impact on the current consumption.
The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD;
MCLR = VDD; WDT enabled/disabled as specified.
For RC oscillator configurations, current through REXT is not included. The current through the resistor can be
estimated by the formula Ir = VDD/2REXT (mA) with REXT in kΩ.
Low-power Timer1 oscillator selected.
BOR and HLVD enable internal band gap reference. With both modules enabled, current consumption will be less
than the sum of both specifications.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 317
PIC18F2X1X/4X1X
25.2
DC Characteristics:
Power-Down and Supply Current
PIC18F2X1X/4X1X (Industrial)
PIC18LF2X1X/4X1X (Industrial) (Continued)
PIC18LF2X1X/4X1X
(Industrial)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
PIC18F2X1X/4X1X
(Industrial, Extended)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
-40°C ≤ TA ≤ +125°C for extended
ParamNo.
Device
Supply Current (IDD)(2,3)
PIC18LF2X1X/4X1X
PIC18LF2X1X/4X1X
All devices
Extended devices only
PIC18LF2X1X/4X1X
PIC18LF2X1X/4X1X
All devices
Extended devices only
Legend:
Note 1:
2:
3:
4:
5:
Typ
Max
Units
Conditions
15
15
15
31.5
30
28.5
µA
µA
µA
-40°C
+25°C
+85°C
40
35
30
105
90
80
80
0.32
0.33
0.33
0.6
0.55
0.6
1.1
1.1
1.0
1
63
60
57
168
160
152
250
1
1
1
1.3
1.2
1.1
2.3
2.2
2.1
3.3
µA
µA
µA
µA
µA
µA
µA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
-40°C
+25°C
+85°C
-40°C
+25°C
+85°C
+125°C
-40°C
+25°C
+85°C
-40°C
+25°C
+85°C
-40°C
+25°C
+85°C
+125°C
VDD = 2.0V
VDD = 3.0V
FOSC = 31 kHz
(RC_RUN mode,
INTRC source)
VDD = 5.0V
VDD = 2.0V
VDD = 3.0V
FOSC = 1 MHz
(RC_RUN mode,
INTOSC source)
VDD = 5.0V
Shading of rows is to assist in readability of the table.
The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured
with the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD or VSS and all features that
add delta current disabled (such as WDT, Timer1 Oscillator, BOR, etc.).
The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin
loading and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have
an impact on the current consumption.
The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD;
MCLR = VDD; WDT enabled/disabled as specified.
For RC oscillator configurations, current through REXT is not included. The current through the resistor can be
estimated by the formula Ir = VDD/2REXT (mA) with REXT in kΩ.
Low-power Timer1 oscillator selected.
BOR and HLVD enable internal band gap reference. With both modules enabled, current consumption will be less
than the sum of both specifications.
DS39636A-page 318
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
25.2
DC Characteristics:
Power-Down and Supply Current
PIC18F2X1X/4X1X (Industrial)
PIC18LF2X1X/4X1X (Industrial) (Continued)
PIC18LF2X1X/4X1X
(Industrial)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
PIC18F2X1X/4X1X
(Industrial, Extended)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
-40°C ≤ TA ≤ +125°C for extended
ParamNo.
Device
Typ
Max
Units
0.8
0.8
0.8
2.1
2.0
1.9
µA
µA
µA
-40°C
+25°C
+85°C
1.3
1.3
1.3
All devices 2.5
2.5
2.5
Extended devices only 2.5
PIC18LF2X1X/4X1X 2.9
3.1
3.6
PIC18LF2X1X/4X1X 4.5
4.8
5.8
All devices 9.2
9.8
11.4
Extended devices only 21
3.0
3.0
3.0
5.3
5.0
4.8
10
8
8
11
11
11
15
16
16
36
180
mA
mA
mA
mA
mA
mA
mA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
-40°C
+25°C
+85°C
-40°C
+25°C
+85°C
+125°C
-40°C
+25°C
+85°C
-40°C
+25°C
+85°C
-40°C
+25°C
+85°C
+125°C
Supply Current (IDD)(2,3)
PIC18LF2X1X/4X1X
PIC18LF2X1X/4X1X
Legend:
Note 1:
2:
3:
4:
5:
Conditions
VDD = 2.0V
VDD = 3.0V
FOSC = 4 MHz
(RC_RUN mode,
INTOSC source)
VDD = 5.0V
VDD = 2.0V
VDD = 3.0V
FOSC = 31 kHz
(RC_IDLE mode,
INTRC source)
VDD = 5.0V
Shading of rows is to assist in readability of the table.
The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured
with the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD or VSS and all features that
add delta current disabled (such as WDT, Timer1 Oscillator, BOR, etc.).
The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin
loading and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have
an impact on the current consumption.
The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD;
MCLR = VDD; WDT enabled/disabled as specified.
For RC oscillator configurations, current through REXT is not included. The current through the resistor can be
estimated by the formula Ir = VDD/2REXT (mA) with REXT in kΩ.
Low-power Timer1 oscillator selected.
BOR and HLVD enable internal band gap reference. With both modules enabled, current consumption will be less
than the sum of both specifications.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 319
PIC18F2X1X/4X1X
25.2
DC Characteristics:
Power-Down and Supply Current
PIC18F2X1X/4X1X (Industrial)
PIC18LF2X1X/4X1X (Industrial) (Continued)
PIC18LF2X1X/4X1X
(Industrial)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
PIC18F2X1X/4X1X
(Industrial, Extended)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
-40°C ≤ TA ≤ +125°C for extended
ParamNo.
Device
Supply Current (IDD)(2,3)
PIC18LF2X1X/4X1X
PIC18LF2X1X/4X1X
All devices
Extended devices only
PIC18LF2X1X/4X1X
PIC18LF2X1X/4X1X
All devices
Extended devices only
Legend:
Note 1:
2:
3:
4:
5:
Typ
Max
Units
Conditions
165
175
190
350
350
350
µA
µA
µA
-40°C
+25°C
+85°C
250
270
290
500
520
550
0.6
340
350
360
520
540
580
1.0
1.1
1.1
1.1
500
500
500
1
1
1
2.9
500
500
500
900
900
900
1.6
1.5
1.4
5.0
µA
µA
µA
mA
mA
mA
mA
µA
µA
µA
µA
µA
µA
mA
mA
mA
mA
-40°C
+25°C
+85°C
-40°C
+25°C
+85°C
+125°C
-40°C
+25°C
+85°C
-40°C
+25°C
+85°C
-40°C
+25°C
+85°C
+125°C
VDD = 2.0V
VDD = 3.0V
FOSC = 1 MHz
(RC_IDLE mode,
INTOSC source)
VDD = 5.0V
VDD = 2.0V
VDD = 3.0V
FOSC = 4 MHz
(RC_IDLE mode,
INTOSC source)
VDD = 5.0V
Shading of rows is to assist in readability of the table.
The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured
with the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD or VSS and all features that
add delta current disabled (such as WDT, Timer1 Oscillator, BOR, etc.).
The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin
loading and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have
an impact on the current consumption.
The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD;
MCLR = VDD; WDT enabled/disabled as specified.
For RC oscillator configurations, current through REXT is not included. The current through the resistor can be
estimated by the formula Ir = VDD/2REXT (mA) with REXT in kΩ.
Low-power Timer1 oscillator selected.
BOR and HLVD enable internal band gap reference. With both modules enabled, current consumption will be less
than the sum of both specifications.
DS39636A-page 320
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
25.2
DC Characteristics:
Power-Down and Supply Current
PIC18F2X1X/4X1X (Industrial)
PIC18LF2X1X/4X1X (Industrial) (Continued)
PIC18LF2X1X/4X1X
(Industrial)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
PIC18F2X1X/4X1X
(Industrial, Extended)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
-40°C ≤ TA ≤ +125°C for extended
ParamNo.
Device
Supply Current (IDD)(2,3)
PIC18LF2X1X/4X1X
PIC18LF2X1X/4X1X
All devices
Extended devices only
PIC18LF2X1X/4X1X
PIC18LF2X1X/4X1X
All devices
Extended devices only
Extended devices only
Typ
Max
Units
Conditions
250
260
250
500
500
500
µA
µA
µA
-40°C
+25°C
+85°C
550
480
460
1.2
1.1
1.0
1.0
0.72
0.74
0.74
1.3
1.3
1.3
2.7
2.6
2.5
2.6
8.4
11
650
650
650
1.6
1.5
1.4
3.5
2.0
2.0
2.0
3.0
3.0
3.0
6.0
6.0
6.0
7.0
21
28
µA
µA
µA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
-40°C
+25°C
+85°C
-40°C
+25°C
+85°C
+125°C
-40°C
+25°C
+85°C
-40°C
+25°C
+85°C
-40°C
+25°C
+85°C
+125°C
+125°C
+125°C
VDD = 2.0V
VDD = 3.0V
FOSC = 1 MHZ
(PRI_RUN,
EC oscillator)
VDD = 5.0V
VDD = 2.0V
VDD = 3.0V
FOSC = 4 MHz
(PRI_RUN,
EC oscillator)
VDD = 5.0V
VDD = 4.2V
VDD = 5.0V
FOSC = 25 MHz
(PRI_RUN,
EC oscillator)
All devices
Legend:
Note 1:
2:
3:
4:
5:
15
35
mA
-40°C
16
35
mA
+25°C
VDD = 4.2V
FOSC = 40 MHZ
16
35
mA
+85°C
(PRI_RUN,
All devices 21
40
mA
-40°C
EC oscillator)
VDD = 5.0V
21
40
mA
+25°C
21
40
mA
+85°C
Shading of rows is to assist in readability of the table.
The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured
with the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD or VSS and all features that
add delta current disabled (such as WDT, Timer1 Oscillator, BOR, etc.).
The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin
loading and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have
an impact on the current consumption.
The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD;
MCLR = VDD; WDT enabled/disabled as specified.
For RC oscillator configurations, current through REXT is not included. The current through the resistor can be
estimated by the formula Ir = VDD/2REXT (mA) with REXT in kΩ.
Low-power Timer1 oscillator selected.
BOR and HLVD enable internal band gap reference. With both modules enabled, current consumption will be less
than the sum of both specifications.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 321
PIC18F2X1X/4X1X
25.2
DC Characteristics:
Power-Down and Supply Current
PIC18F2X1X/4X1X (Industrial)
PIC18LF2X1X/4X1X (Industrial) (Continued)
PIC18LF2X1X/4X1X
(Industrial)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
PIC18F2X1X/4X1X
(Industrial, Extended)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
-40°C ≤ TA ≤ +125°C for extended
ParamNo.
Device
Supply Current (IDD)(2,3)
All devices
Extended devices only
All devices
Extended devices only
All devices
All devices
Legend:
Note 1:
2:
3:
4:
5:
Typ
Max
Units
Conditions
7.5
7.4
7.3
16
15
14
mA
mA
mA
-40°C
+25°C
+85°C
8.0
10
10
9.7
10
17
17
17
23
23
23
25
21
20
19
35
35
35
35
40
40
40
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
+125°C
-40°C
+25°C
+85°C
+125°C
-40°C
+25°C
+85°C
-40°C
+25°C
+85°C
VDD = 4.2V
FOSC = 4 MHZ
(PRI_RUN HS+PLL)
VDD = 5.0V
FOSC = 4 MHZ
(PRI_RUN HS+PLL)
VDD = 4.2V
FOSC = 10 MHZ
(PRI_RUN HS+PLL)
VDD = 5.0V
FOSC = 10 MHZ
(PRI_RUN HS+PLL)
Shading of rows is to assist in readability of the table.
The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured
with the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD or VSS and all features that
add delta current disabled (such as WDT, Timer1 Oscillator, BOR, etc.).
The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin
loading and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have
an impact on the current consumption.
The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD;
MCLR = VDD; WDT enabled/disabled as specified.
For RC oscillator configurations, current through REXT is not included. The current through the resistor can be
estimated by the formula Ir = VDD/2REXT (mA) with REXT in kΩ.
Low-power Timer1 oscillator selected.
BOR and HLVD enable internal band gap reference. With both modules enabled, current consumption will be less
than the sum of both specifications.
DS39636A-page 322
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
25.2
DC Characteristics:
Power-Down and Supply Current
PIC18F2X1X/4X1X (Industrial)
PIC18LF2X1X/4X1X (Industrial) (Continued)
PIC18LF2X1X/4X1X
(Industrial)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
PIC18F2X1X/4X1X
(Industrial, Extended)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
-40°C ≤ TA ≤ +125°C for extended
ParamNo.
Device
Typ
Max
Units
Conditions
65
65
130
120
µA
µA
-40°C
+25°C
70
120
120
130
300
240
300
320
260
255
270
420
430
450
0.9
0.9
0.9
1
2.8
4.3
115
270
250
240
480
450
430
900
475
450
430
900
850
810
1.5
1.4
1.3
1.2
7.0
11
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
mA
mA
mA
mA
mA
mA
+85°C
-40°C
+25°C
+85°C
-40°C
+25°C
+85°C
+125°C
-40°C
+25°C
+85°C
-40°C
+25°C
+85°C
-40°C
+25°C
+85°C
+125°C
+125°C
+125°C
(IDD)(2,3)
Supply Current
PIC18LF2X1X/4X1X
PIC18LF2X1X/4X1X
All devices
Extended devices only
PIC18LF2X1X/4X1X
PIC18LF2X1X/4X1X
All devices
Extended devices only
Extended devices only
VDD = 2.0V
VDD = 3.0V
FOSC = 1 MHz
(PRI_IDLE mode,
EC oscillator)
VDD = 5.0V
VDD = 2.0V
VDD = 3.0V
FOSC = 4 MHz
(PRI_IDLE mode,
EC oscillator)
VDD = 5.0V
VDD = 4.2V
VDD = 5.0V
FOSC = 25 MHz
(PRI_IDLE mode,
EC oscillator)
All devices
Legend:
Note 1:
2:
3:
4:
5:
6.0
16
mA
-40°C
VDD = 4.2V
6.2
16
mA
+25°C
FOSC = 40 MHz
6.6
16
mA
+85°C
(PRI_IDLE mode,
All devices 8.1
18
mA
-40°C
EC oscillator)
VDD = 5.0V
9.1
18
mA
+25°C
8.3
18
mA
+85°C
Shading of rows is to assist in readability of the table.
The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured
with the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD or VSS and all features that
add delta current disabled (such as WDT, Timer1 Oscillator, BOR, etc.).
The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin
loading and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have
an impact on the current consumption.
The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD;
MCLR = VDD; WDT enabled/disabled as specified.
For RC oscillator configurations, current through REXT is not included. The current through the resistor can be
estimated by the formula Ir = VDD/2REXT (mA) with REXT in kΩ.
Low-power Timer1 oscillator selected.
BOR and HLVD enable internal band gap reference. With both modules enabled, current consumption will be less
than the sum of both specifications.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 323
PIC18F2X1X/4X1X
25.2
DC Characteristics:
Power-Down and Supply Current
PIC18F2X1X/4X1X (Industrial)
PIC18LF2X1X/4X1X (Industrial) (Continued)
PIC18LF2X1X/4X1X
(Industrial)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
PIC18F2X1X/4X1X
(Industrial, Extended)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
-40°C ≤ TA ≤ +125°C for extended
ParamNo.
Device
Typ
Max
Units
14
15
16
40
40
40
µA
µA
µA
Conditions
(IDD)(2,3)
Supply Current
PIC18LF2X1X/4X1X
-40°C
+25°C
+85°C
VDD = 2.0V
40
74
µA
-40°C
FOSC = 32 kHz(4)
35
70
µA
+25°C
VDD = 3.0V
(SEC_RUN mode,
Timer1 as clock)
31
67
µA
+85°C
All devices 99
150
µA
-40°C
VDD = 5.0V
81
150
µA
+25°C
75
150
µA
+85°C
PIC18LF2X1X/4X1X 2.5
12
µA
-40°C
3.7
12
µA
+25°C
VDD = 2.0V
4.5
12
µA
+85°C
PIC18LF2X1X/4X1X 5.0
15
µA
-40°C
FOSC = 32 kHz(4)
VDD = 3.0V
5.4
15
µA
+25°C
(SEC_IDLE mode,
Timer1 as clock)
6.3
15
µA
+85°C
All devices 8.5
25
µA
-40°C
VDD = 5.0V
9.0
25
µA
+25°C
10.5
36
µA
+85°C
Shading of rows is to assist in readability of the table.
The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured
with the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD or VSS and all features that
add delta current disabled (such as WDT, Timer1 Oscillator, BOR, etc.).
The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin
loading and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have
an impact on the current consumption.
The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD;
MCLR = VDD; WDT enabled/disabled as specified.
For RC oscillator configurations, current through REXT is not included. The current through the resistor can be
estimated by the formula Ir = VDD/2REXT (mA) with REXT in kΩ.
Low-power Timer1 oscillator selected.
BOR and HLVD enable internal band gap reference. With both modules enabled, current consumption will be less
than the sum of both specifications.
PIC18LF2X1X/4X1X
Legend:
Note 1:
2:
3:
4:
5:
DS39636A-page 324
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
25.2
DC Characteristics:
Power-Down and Supply Current
PIC18F2X1X/4X1X (Industrial)
PIC18LF2X1X/4X1X (Industrial) (Continued)
PIC18LF2X1X/4X1X
(Industrial)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
PIC18F2X1X/4X1X
(Industrial, Extended)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
-40°C ≤ TA ≤ +125°C for extended
ParamNo.
D022
(∆IWDT)
D022A
(∆IBOR)
D022B
(∆ILVD)
D025
(∆IOSCB)
D026
(∆IAD)
Device
Brown-out Reset(5)
High/Low-Voltage
Detect(5)
Timer1 Oscillator
A/D Converter
Legend:
Note 1:
2:
3:
4:
5:
Typ
Max
Units
Conditions
Module Differential Currents (∆IWDT, ∆IBOR, ∆ILVD, ∆IOSCB, ∆IAD)
Watchdog Timer 1.3
3.8
µA
-40°C
1.4
3.8
µA
+25°C
2.0
3.8
µA
+85°C
VDD = 2.0V
1.9
2.0
2.8
4.0
5.5
5.6
13
35
40
55
0
4.6
4.6
4.6
10
10
10
13
40
45
45
5
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
-40°C
+25°C
+85°C
-40°C
+25°C
+85°C
+125°C
-40°C to +85°C
-40°C to +85°C
-40°C to +125°C
-40°C to +125°C
22
25
29
30
2.1
38
40
45
45
4.5
µA
µA
µA
µA
µA
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +125°C
-40°C
VDD = 2.0V
VDD = 3.0V
1.8
2.1
2.2
2.6
2.9
3.0
4.5
4.5
6.0
6.0
6.0
8.0
µA
µA
µA
µA
µA
µA
+25°C
+85°C
-40°C
+25°C
+85°C
-40°C
VDD = 2.0V
32 kHz on Timer1(4)
VDD = 3.0V
32 kHz on Timer1(4)
3.2
3.4
1.0
1.0
1.0
2.0
8.0
8.0
2.0
2.0
2.0
8.0
µA
µA
µA
µA
µA
µA
+25°C
+85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +125°C
VDD = 5.0V
32 kHz on Timer1(4)
VDD = 3.0V
VDD = 5.0V
VDD = 3.0V
VDD = 5.0V
Sleep mode,
BOREN1:BOREN0 = 10
VDD = 5.0V
VDD = 2.0V
VDD = 3.0V
A/D on, not converting
VDD = 5.0V
Shading of rows is to assist in readability of the table.
The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured
with the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD or VSS and all features that
add delta current disabled (such as WDT, Timer1 Oscillator, BOR, etc.).
The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin
loading and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have
an impact on the current consumption.
The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD;
MCLR = VDD; WDT enabled/disabled as specified.
For RC oscillator configurations, current through REXT is not included. The current through the resistor can be
estimated by the formula Ir = VDD/2REXT (mA) with REXT in kΩ.
Low-power Timer1 oscillator selected.
BOR and HLVD enable internal band gap reference. With both modules enabled, current consumption will be less
than the sum of both specifications.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 325
PIC18F2X1X/4X1X
25.3
DC Characteristics: PIC18F2X1X/4X1X (Industrial)
PIC18LF2X1X/4X1X (Industrial)
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ +85°C for industrial
DC CHARACTERISTICS
Param
Symbol
No.
VIL
Characteristic
Min
Max
Units
Conditions
VSS
0.15 VDD
V
VDD < 4.5V
—
0.8
V
4.5V ≤ VDD ≤ 5.5V
VSS
VSS
0.2 VDD
0.3 VDD
V
V
VSS
0.2 VDD
V
Input Low Voltage
I/O ports:
D030
with TTL buffer
D030A
D031
with Schmitt Trigger buffer
RC3 and RC4
D032
MCLR
D033
OSC1
VSS
0.3 VDD
V
HS, HSPLL modes
D033A
D033B
D034
OSC1
OSC1
T13CKI
VSS
VSS
VSS
0.2 VDD
0.3 VDD
0.3 VDD
V
V
V
RC, EC modes(1)
XT, LP modes
0.25 VDD + 0.8V
VDD
V
VDD < 4.5V
4.5V ≤ VDD ≤ 5.5V
VIH
Input High Voltage
I/O ports:
D040
with TTL buffer
D040A
D041
with Schmitt Trigger buffer
RC3 and RC4
2.0
VDD
V
0.8 VDD
0.7 VDD
VDD
VDD
V
V
D042
MCLR
0.8 VDD
VDD
V
D043
OSC1
0.7 VDD
VDD
V
HS, HSPLL modes
D043A
D043B
D043C
D044
OSC1
OSC1
OSC1
T13CKI
0.8 VDD
0.9 VDD
1.6
1.6
VDD
VDD
VDD
VDD
V
V
V
V
EC mode
RC mode(1)
XT, LP modes
I/O ports
—
±1
µA
VSS ≤ VPIN ≤ VDD,
Pin at high-impedance
D061
MCLR
—
±5
µA
Vss ≤ VPIN ≤ VDD
D063
OSC1
—
±5
µA
Vss ≤ VPIN ≤ VDD
50
400
µA
VDD = 5V, VPIN = VSS
IIL
D060
D070
Note 1:
2:
3:
4:
Input Leakage Current(2,3)
IPU
Weak Pull-up Current
IPURB
PORTB weak pull-up current
In RC oscillator configuration, the OSC1/CLKI pin is a Schmitt Trigger input. It is not recommended that the
PICmicro® device be driven with an external clock while in RC mode.
The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified
levels represent normal operating conditions. Higher leakage current may be measured at different input
voltages.
Negative current is defined as current sourced by the pin.
Parameter is characterized but not tested.
DS39636A-page 326
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
25.3
DC Characteristics: PIC18F2X1X/4X1X (Industrial)
PIC18LF2X1X/4X1X (Industrial) (Continued)
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ +85°C for industrial
DC CHARACTERISTICS
Param
Symbol
No.
VOL
Characteristic
Min
Max
Units
Conditions
Output Low Voltage
D080
I/O ports
—
0.6
V
IOL = 8.5 mA, VDD = 4.5V,
-40°C to +85°C
D083
OSC2/CLKO
(RC, RCIO, EC, ECIO modes)
—
0.6
V
IOL = 1.6 mA, VDD = 4.5V,
-40°C to +85°C
VOH
Output High Voltage(3)
D090
I/O ports
VDD – 0.7
—
V
IOH = -3.0 mA, VDD = 4.5V,
-40°C to +85°C
D092
OSC2/CLKO
(RC, RCIO, EC, ECIO modes)
VDD – 0.7
—
V
IOH = -1.3 mA, VDD = 4.5V,
-40°C to +85°C
Capacitive Loading Specs
on Output Pins
D100(4) COSC2
OSC2 pin
—
15
pF
In XT, HS and LP modes
when external clock is
used to drive OSC1
D101
CIO
All I/O pins and OSC2
(in RC mode)
—
50
pF
To meet the AC Timing
Specifications
D102
CB
SCL, SDA
—
400
pF
I2C™ Specification
Note 1:
2:
3:
4:
In RC oscillator configuration, the OSC1/CLKI pin is a Schmitt Trigger input. It is not recommended that the
PICmicro® device be driven with an external clock while in RC mode.
The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified
levels represent normal operating conditions. Higher leakage current may be measured at different input
voltages.
Negative current is defined as current sourced by the pin.
Parameter is characterized but not tested.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 327
PIC18F2X1X/4X1X
TABLE 25-1:
MEMORY PROGRAMMING REQUIREMENTS
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ +85°C for industrial
DC Characteristics
Param
No.
Sym
Characteristic
Min
Typ†
Max
Units
Conditions
VDD + 4
—
12.5
V
—
10
—
mA
E/W -40°C to +85°C
Internal Program Memory
Programming Specifications(1)
D110
VPP
Voltage on MCLR/VPP/RE3 pin
(Note 2)
D113
IDDP
Supply Current during
Programming
D130
EP
Cell Endurance
10K
100K
—
D131
VPR
VDD for Read
VMIN
—
5.5
V
VMIN = Minimum operating
voltage
D132
VIE
VDD for Block Erase
4.5
—
5.5
V
Using ICSP™ port
D132A
VIW
VDD for Externally Timed Erase
or Write
4.5
—
5.5
V
Using ICSP port
D133
TIE
ICSP Block Erase Cycle Time
—
4
—
ms
VDD > 4.5V
ICSP Erase or Write Cycle Time
(externally timed)
1
—
—
ms
VDD > 4.5V
40
100
—
Program Flash Memory
D133A TIW
D134
TRETD Characteristic Retention
Year Provided no other
specifications are violated
† Data in “Typ” column is at 5.0V, 25°C unless otherwise stated. These parameters are for design guidance
only and are not tested.
Note 1: These specifications are for programming the on-chip program memory through the use of table write
instructions.
2: Required only if Single-Supply programming is disabled.
DS39636A-page 328
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
TABLE 25-2:
COMPARATOR SPECIFICATIONS
Operating Conditions: 3.0V < VDD < 5.5V, -40°C < TA < +85°C (unless otherwise stated).
Param
No.
Sym
Characteristics
Min
Typ
Max
Units
D300
VIOFF
Input Offset Voltage
—
± 5.0
± 10
mV
D301
VICM
Input Common Mode Voltage*
0
—
VDD – 1.5
V
Comments
D302
CMRR
Common Mode Rejection Ratio*
55
—
—
dB
300
TRESP
Response Time(1)*
—
150
400
ns
PIC18FXXXX
—
150
600
ns
PIC18LFXXXX,
VDD = 2.0V
—
—
10
µs
300A
301
*
Note 1:
TMC2OV
Comparator Mode Change to
Output Valid*
These parameters are characterized but not tested.
Response time measured with one comparator input at (VDD – 1.5)/2, while the other input transitions
from VSS to VDD.
TABLE 25-3:
VOLTAGE REFERENCE SPECIFICATIONS
Operating Conditions: 3.0V < VDD < 5.5V, -40°C < TA < +85°C (unless otherwise stated).
Param
No.
Sym
Characteristics
Min
Typ
Max
Units
D310
VRES
Resolution
VDD/24
—
VDD/32
LSb
D311
VRAA
Absolute Accuracy
—
—
1/2
LSb
D312
VRUR
Unit Resistor Value (R)*
—
2k
—
Ω
310
TSET
Settling Time(1)*
—
—
10
µs
*
Note 1:
Comments
These parameters are characterized but not tested.
Settling time measured while CVRR = 1 and CVR3:CVR0 transitions from ‘0000’ to ‘1111’.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 329
PIC18F2X1X/4X1X
FIGURE 25-4:
HIGH/LOW-VOLTAGE DETECT CHARACTERISTICS
VDD
(HLVDIF can be
cleared in software)
VLVD
(HLVDIF set by hardware)
HLVDIF(1)
Note 1: VDIRMAG = 0.
TABLE 25-4:
HIGH/LOW-VOLTAGE DETECT CHARACTERISTICS
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ +85°C for industrial
Param
Symbol
No.
D420
Characteristic
Min
Typ†
Max
Units
HLVD Voltage on VDD LVV = 0000
Transition High to Low LVV = 0001
2.06
2.17
2.28
V
2.12
2.23
2.34
V
LVV = 0010
2.24
2.36
2.48
V
LVV = 0011
2.32
2.44
2.56
V
LVV = 0100
2.47
2.60
2.73
V
LVV = 0101
2.65
2.79
2.93
V
LVV = 0110
2.74
2.89
3.04
V
LVV = 0111
2.96
3.12
3.28
V
LVV = 1000
3.22
3.39
3.56
V
LVV = 1001
3.37
3.55
3.73
V
LVV = 1010
3.52
3.71
3.90
V
LVV = 1011
3.70
3.90
4.10
V
LVV = 1100
3.90
4.11
4.32
V
LVV = 1101
4.11
4.33
4.55
V
LVV = 1110
4.36
4.59
4.82
V
Conditions
† Production tested at TAMB = 25°C. Specifications over temperature limits ensured by characterization.
DS39636A-page 330
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
25.4
25.4.1
AC (Timing) Characteristics
TIMING PARAMETER SYMBOLOGY
The timing parameter symbols have been created
using one of the following formats:
1. TppS2ppS
2. TppS
T
F
Frequency
Lowercase letters (pp) and their meanings:
pp
cc
CCP1
ck
CLKO
cs
CS
di
SDI
do
SDO
dt
Data in
io
I/O port
mc
MCLR
Uppercase letters and their meanings:
S
F
Fall
H
High
I
Invalid (High-impedance)
L
Low
I2C only
AA
output access
BUF
Bus free
TCC:ST (I2C specifications only)
CC
HD
Hold
ST
DAT
DATA input hold
STA
Start condition
 2004 Microchip Technology Inc.
3. TCC:ST
4. Ts
(I2C specifications only)
(I2C specifications only)
T
Time
osc
rd
rw
sc
ss
t0
t1
wr
OSC1
RD
RD or WR
SCK
SS
T0CKI
T13CKI
WR
P
R
V
Z
Period
Rise
Valid
High-impedance
High
Low
High
Low
SU
Setup
STO
Stop condition
Preliminary
DS39636A-page 331
PIC18F2X1X/4X1X
25.4.2
TIMING CONDITIONS
Note:
The temperature and voltages specified in Table 25-5
apply to all timing specifications unless otherwise
noted. Figure 25-5 specifies the load conditions for the
timing specifications.
TABLE 25-5:
Because of space limitations, the generic
terms “PIC18FXXXX” and “PIC18LFXXXX”
are used throughout this section to refer to
the PIC18F2X1X/4X1X and PIC18LF2X1X/
4X1X families of devices specifically and
only those devices.
TEMPERATURE AND VOLTAGE SPECIFICATIONS – AC
AC CHARACTERISTICS
FIGURE 25-5:
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
Operating voltage VDD range as described in DC spec Section 25.1 and
Section 25.3.
LF parts operate for industrial temperatures only.
LOAD CONDITIONS FOR DEVICE TIMING SPECIFICATIONS
Load Condition 1
Load Condition 2
VDD/2
RL
CL
Pin
VSS
CL
Pin
RL = 464Ω
VSS
DS39636A-page 332
CL = 50 pF
Preliminary
for all pins except OSC2/CLKO
and including D and E outputs as ports
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
25.4.3
TIMING DIAGRAMS AND SPECIFICATIONS
FIGURE 25-6:
EXTERNAL CLOCK TIMING (ALL MODES EXCEPT PLL)
Q4
Q1
Q2
Q3
Q4
Q1
OSC1
1
3
4
3
4
2
CLKO
TABLE 25-6:
Param.
No.
1A
EXTERNAL CLOCK TIMING REQUIREMENTS
Symbol
FOSC
Characteristic
Min
External CLKI Frequency(1)
DC
1
MHz
XT, RC Oscillator mode
DC
20
MHz
HS Oscillator mode
DC
31.25
kHz
LP Oscillator mode
DC
4
MHz
RC Oscillator mode
0.1
4
MHz
XT Oscillator mode
4
20
MHz
HS Oscillator mode
5
200
kHz
LP Oscillator mode
1000
—
ns
XT, RC Oscillator mode
50
—
ns
HS Oscillator mode
32
—
µs
LP Oscillator mode
250
—
ns
RC Oscillator mode
250
1
µs
XT Oscillator mode
100
250
ns
HS Oscillator mode
50
250
ns
HS Oscillator mode
5
—
µs
LP Oscillator mode
100
—
ns
TCY = 4/FOSC, Industrial
160
—
ns
TCY = 4/FOSC, Extended
Oscillator Frequency
1
TOSC
(1)
External CLKI Period(1)
(1)
Oscillator Period
2
3
4
Note 1:
TCY
Instruction Cycle Time(1)
TOSL,
TOSH
External Clock in (OSC1)
High or Low Time
TOSR,
TOSF
External Clock in (OSC1)
Rise or Fall Time
Max
Units
Conditions
30
—
ns
XT Oscillator mode
2.5
—
µs
LP Oscillator mode
10
—
ns
HS Oscillator mode
—
20
ns
XT Oscillator mode
—
50
ns
LP Oscillator mode
—
7.5
ns
HS Oscillator mode
Instruction cycle period (TCY) equals four times the input oscillator time base period for all configurations
except PLL. All specified values are based on characterization data for that particular oscillator type under
standard operating conditions with the device executing code. Exceeding these specified limits may result
in an unstable oscillator operation and/or higher than expected current consumption. All devices are tested
to operate at “min.” values with an external clock applied to the OSC1/CLKI pin. When an external clock
input is used, the “max.” cycle time limit is “DC” (no clock) for all devices.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 333
PIC18F2X1X/4X1X
TABLE 25-7:
Param
No.
PLL CLOCK TIMING SPECIFICATIONS (VDD = 4.2V TO 5.5V)
Sym
Characteristic
Min
Typ†
Max
4
16
—
—
10
40
Units
F10
F11
FOSC Oscillator Frequency Range
FSYS On-Chip VCO System Frequency
F12
trc
PLL Start-up Time (Lock Time)
—
—
2
ms
∆CLK
CLKO Stability (Jitter)
-2
—
+2
%
F13
Conditions
MHz HS mode only
MHz HS mode only
† Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance
only and are not tested.
TABLE 25-8:
AC CHARACTERISTICS: INTERNAL RC ACCURACY
PIC18F2X1X/4X1X (INDUSTRIAL)
PIC18LF2X1X/4X1X (INDUSTRIAL)
PIC18LF2X1X/4X1X
(Industrial)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
PIC18F2X1X/4X1X
(Industrial)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
Param
No.
Device
Min
Typ
Max
Units
Conditions
INTOSC Accuracy @ Freq = 8 MHz, 4 MHz, 2 MHz, 1 MHz, 500 kHz, 250 kHz, 125 kHz, 31 kHz(1)
PIC18LF2X1X/4X1X
-2
+/-1
2
%
-5
—
5
%
-10°C to +85°C VDD = 2.7-3.3V
-10
+/-1
10
%
-40°C to +85°C VDD = 2.7-3.3V
-2
+/-1
2
%
-5
—
5
%
-10°C to +85°C VDD = 4.5-5.5V
-10
+/-1
10
%
-40°C to +85°C VDD = 4.5-5.5V
PIC18LF2X1X/4X1X 26.562
—
35.938
kHz
-40°C to +85°C VDD = 2.7-3.3V
PIC18F2X1X/4X1X 26.562
—
35.938
kHz
-40°C to +85°C VDD = 4.5-5.5V
PIC18F2X1X/4X1X
+25°C
+25°C
VDD = 2.7-3.3V
VDD = 4.5-5.5V
INTRC Accuracy @ Freq = 31 kHz(2)
Legend:
Note 1:
2:
3:
Shading of rows is to assist in readability of the table.
Frequency calibrated at 25°C. OSCTUNE register can be used to compensate for temperature drift.
INTRC frequency after calibration.
Change of INTRC frequency as VDD changes.
DS39636A-page 334
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
FIGURE 25-7:
CLKO AND I/O TIMING
Q1
Q4
Q2
Q3
OSC1
11
10
CLKO
13
19
14
12
18
16
I/O pin
(Input)
15
17
I/O pin
(Output)
Note:
20, 21
Refer to Figure 25-5 for load conditions.
TABLE 25-9:
Param
No.
10
New Value
Old Value
CLKO AND I/O TIMING REQUIREMENTS
Symbol
Characteristic
TosH2ckL OSC1 ↑ to CLKO ↓
Min
Typ
Max
—
75
200
Units Conditions
ns
(Note 1)
11
TosH2ckH OSC1 ↑ to CLKO ↑
—
75
200
ns
(Note 1)
12
TckR
CLKO Rise Time
—
35
100
ns
(Note 1)
13
TckF
CLKO Fall Time
—
35
100
ns
(Note 1)
14
TckL2ioV
CLKO ↓ to Port Out Valid
—
—
0.5 TCY + 20
ns
(Note 1)
15
TioV2ckH Port In Valid before CLKO ↑
16
TckH2ioI
17
TosH2ioV OSC1 ↑ (Q1 cycle) to Port Out Valid
18
TosH2ioI
18A
0.25 TCY + 25
—
—
ns
(Note 1)
0
—
—
ns
(Note 1)
Port In Hold after CLKO ↑
OSC1 ↑ (Q2 cycle) to
Port Input Invalid
(I/O in hold time)
—
50
150
ns
PIC18FXXXX
100
—
—
ns
PIC18LFXXXX
200
—
—
ns
19
TioV2osH Port Input Valid to OSC1 ↑ (I/O in setup time)
0
—
—
ns
20
TioR
Port Output Rise Time
20A
21
TioF
Port Output Fall Time
21A
PIC18FXXXX
—
10
25
ns
PIC18LFXXXX
—
—
60
ns
PIC18FXXXX
—
10
25
ns
PIC18LFXXXX
—
—
60
ns
22†
TINP
INT pin High or Low Time
TCY
—
—
ns
23†
TRBP
RB7:RB4 Change INT High or Low Time
TCY
—
—
ns
VDD = 2.0V
VDD = 2.0V
VDD = 2.0V
† These parameters are asynchronous events not related to any internal clock edges.
Note 1: Measurements are taken in RC mode, where CLKO output is 4 x TOSC.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 335
PIC18F2X1X/4X1X
FIGURE 25-8:
RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER AND
POWER-UP TIMER TIMING
VDD
MCLR
30
Internal
POR
33
PWRT
Time-out
32
OSC
Time-out
Internal
Reset
Watchdog
Timer
Reset
31
34
34
I/O pins
Note:
Refer to Figure 25-5 for load conditions.
FIGURE 25-9:
BROWN-OUT RESET TIMING
BVDD
VDD
35
VIRVST
Enable Internal
Reference Voltage
Internal Reference
Voltage Stable
36
TABLE 25-10: RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER, POWER-UP TIMER
AND BROWN-OUT RESET REQUIREMENTS
Param.
Symbol
No.
Characteristic
Min
30
TmcL
MCLR Pulse Width (low)
31
TWDT
Watchdog Timer Time-out Period
(no postscaler)
32
33
TOST
TPWRT
Oscillation Start-up Timer Period
Power-up Timer Period
34
TIOZ
35
TBOR
I/O High-Impedance from MCLR
Low or Watchdog Timer Reset
Brown-out Reset Pulse Width
36
TIVRST
37
TLVD
Time for Internal Reference
Voltage to become Stable
High/Low-Voltage Detect Pulse Width
38
39
TCSD
TIOBST
CPU Start-up Time
Time for INTOSC to Stabilize
DS39636A-page 336
Typ
Max
Units
2
—
—
µs
3.4
4.0
4.6
ms
1024 TOSC — 1024 TOSC
55.6
65.5
75
—
ms
—
2
—
µs
200
—
—
µs
—
20
50
µs
200
—
—
µs
—
—
10
1
—
—
µs
µs
Preliminary
Conditions
TOSC = OSC1 period
VDD ≤ BVDD (see D005)
VDD ≤ VLVD
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
FIGURE 25-10:
TIMER0 AND TIMER1 EXTERNAL CLOCK TIMINGS
T0CKI
41
40
42
T1OSO/T13CKI
46
45
47
48
TMR0 or
TMR1
Note:
Refer to Figure 25-5 for load conditions.
TABLE 25-11: TIMER0 AND TIMER1 EXTERNAL CLOCK REQUIREMENTS
Param
No.
Symbol
Characteristic
40
Tt0H
T0CKI High Pulse Width
41
Tt0L
T0CKI Low Pulse Width
42
Tt0P
T0CKI Period
No prescaler
With prescaler
No prescaler
With prescaler
45
Tt1H
47
0.5 TCY + 20
—
ns
10
—
ns
0.5 TCY + 20
—
ns
—
ns
—
ns
With prescaler
Greater of:
20 ns or
(TCY + 40)/N
—
ns
T13CKI
Synchronous, no prescaler
High Time Synchronous,
PIC18FXXXX
with prescaler
PIC18LFXXXX
0.5 TCY + 20
—
ns
10
—
ns
25
—
ns
30
—
ns
PIC18FXXXX
T13CKI
Low Time
Synchronous, no prescaler
—
ns
—
ns
VDD = 2.0V
VDD = 2.0V
PIC18FXXXX
10
—
ns
PIC18LFXXXX
25
—
ns
Asynchronous
PIC18FXXXX
30
—
ns
PIC18LFXXXX
50
—
ns
VDD = 2.0V
Greater of:
20 ns or
(TCY + 40)/N
—
ns
N = prescale
value (1, 2, 4, 8)
Tt1P
T13CKI
Input
Period
Ft1
T13CKI Oscillator Input Frequency Range
Synchronous
Tcke2tmrI Delay from External T13CKI Clock Edge to
Timer Increment
 2004 Microchip Technology Inc.
50
0.5 TCY + 5
N = prescale
value
(1, 2, 4,..., 256)
Synchronous,
with prescaler
Asynchronous
48
Units Conditions
10
No prescaler
PIC18LFXXXX
Tt1L
Max
TCY + 10
Asynchronous
46
Min
Preliminary
60
—
ns
DC
50
kHz
2 TOSC
7 TOSC
—
VDD = 2.0V
DS39636A-page 337
PIC18F2X1X/4X1X
FIGURE 25-11:
CAPTURE/COMPARE/PWM TIMINGS (ALL CCP MODULES)
CCPx
(Capture Mode)
50
51
52
CCPx
(Compare or PWM Mode)
54
53
Note:
Refer to Figure 25-5 for load conditions.
TABLE 25-12: CAPTURE/COMPARE/PWM REQUIREMENTS (ALL CCP MODULES)
Param
Symbol
No.
50
51
TccL
TccH
Characteristic
Min
Max
Units
CCPx Input Low No prescaler
Time
With
PIC18FXXXX
prescaler PIC18LFXXXX
0.5 TCY + 20
—
ns
10
—
ns
20
—
ns
CCPx Input
High Time
0.5 TCY + 20
—
ns
No prescaler
With
prescaler
52
TccP
CCPx Input Period
53
TccR
CCPx Output Fall Time
54
TccF
CCPx Output Fall Time
DS39636A-page 338
Conditions
VDD = 2.0V
PIC18FXXXX
10
—
ns
PIC18LFXXXX
20
—
ns
VDD = 2.0V
3 TCY + 40
N
—
ns
N = prescale
value (1, 4 or 16)
—
25
ns
PIC18FXXXX
PIC18LFXXXX
—
45
ns
PIC18FXXXX
—
25
ns
PIC18LFXXXX
—
45
ns
Preliminary
VDD = 2.0V
VDD = 2.0V
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
FIGURE 25-12:
PARALLEL SLAVE PORT TIMING (PIC18F4410/4510/4515/4610)
RE2/CS
RE0/RD
RE1/WR
65
RD7:RD0
62
64
63
Note:
Refer to Figure 25-5 for load conditions.
TABLE 25-13: PARALLEL SLAVE PORT REQUIREMENTS (PIC18F4410/4510/4515/4610)
Param.
No.
Symbol
Characteristic
Min
Max
Units
62
TdtV2wrH
Data In Valid before WR ↑ or CS ↑ (setup time)
20
—
ns
63
TwrH2dtI
WR ↑ or CS ↑ to Data–In
Invalid (hold time)
PIC18FXXXX
20
—
ns
PIC18LFXXXX
35
—
ns
64
TrdL2dtV
RD ↓ and CS ↓ to Data–Out Valid
—
80
ns
65
TrdH2dtI
RD ↑ or CS ↓ to Data–Out Invalid
10
30
ns
66
TibfINH
Inhibit of the IBF Flag bit being Cleared from
WR ↑ or CS ↑
—
3 TCY
 2004 Microchip Technology Inc.
Preliminary
Conditions
VDD = 2.0V
DS39636A-page 339
PIC18F2X1X/4X1X
FIGURE 25-13:
EXAMPLE SPI™ MASTER MODE TIMING (CKE = 0)
SS
70
SCK
(CKP = 0)
71
72
78
79
79
78
SCK
(CKP = 1)
80
bit 6 - - - - - -1
MSb
SDO
LSb
75, 76
SDI
MSb In
bit 6 - - - -1
LSb In
74
73
Note:
Refer to Figure 25-5 for load conditions.
TABLE 25-14: EXAMPLE SPI™ MODE REQUIREMENTS (MASTER MODE, CKE = 0)
Param
No.
Symbol
Characteristic
70
TssL2scH,
TssL2scL
SS ↓ to SCK ↓ or SCK ↑ Input
71
TscH
SCK Input High Time
(Slave mode)
SCK Input Low Time
(Slave mode)
71A
72
TscL
72A
Min
Max Units
TCY
—
ns
Continuous
1.25 TCY + 30
—
ns
Single Byte
40
—
ns
Continuous
1.25 TCY + 30
—
ns
Single Byte
40
—
ns
100
—
ns
1.5 TCY + 40
—
ns
100
—
ns
PIC18FXXXX
—
25
ns
PIC18LFXXXX
—
45
ns
—
25
ns
73
TdiV2scH,
TdiV2scL
Setup Time of SDI Data Input to SCK Edge
73A
Tb2b
Last Clock Edge of Byte 1 to the 1st Clock Edge
of Byte 2
74
TscH2diL,
TscL2diL
Hold Time of SDI Data Input to SCK Edge
75
TdoR
SDO Data Output Rise Time
76
TdoF
SDO Data Output Fall Time
78
TscR
SCK Output Rise Time
(Master mode)
PIC18FXXXX
—
25
ns
PIC18LFXXXX
—
45
ns
79
TscF
SCK Output Fall Time (Master mode)
—
25
ns
80
TscH2doV,
TscL2doV
SDO Data Output Valid after
SCK Edge
PIC18FXXXX
—
50
ns
PIC18LFXXXX
—
100
ns
Note 1:
2:
Conditions
(Note 1)
(Note 1)
(Note 2)
VDD = 2.0V
VDD = 2.0V
VDD = 2.0V
Requires the use of Parameter #73A.
Only if Parameter #71A and #72A are used.
DS39636A-page 340
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
FIGURE 25-14:
EXAMPLE SPI™ MASTER MODE TIMING (CKE = 1)
SS
81
SCK
(CKP = 0)
71
72
79
73
SCK
(CKP = 1)
80
78
MSb
SDO
bit 6 - - - - - -1
LSb
bit 6 - - - -1
LSb In
75, 76
SDI
MSb In
74
Note:
Refer to Figure 25-5 for load conditions.
TABLE 25-15: EXAMPLE SPI™ MODE REQUIREMENTS (MASTER MODE, CKE = 1)
Param.
No.
71
Symbol
TscH
71A
72
TscL
72A
Characteristic
SCK Input High Time
(Slave mode)
SCK Input Low Time
(Slave mode)
Min
Max Units
Continuous
1.25 TCY + 30
—
ns
Single Byte
40
—
ns
Continuous
1.25 TCY + 30
—
ns
Single Byte
40
—
ns
100
—
ns
1.5 TCY + 40
—
ns
100
—
ns
—
25
ns
45
ns
—
25
ns
—
25
ns
45
ns
73
TdiV2scH,
TdiV2scL
Setup Time of SDI Data Input to SCK Edge
73A
Tb2b
Last Clock Edge of Byte 1 to the 1st Clock Edge
of Byte 2
74
TscH2diL,
TscL2diL
Hold Time of SDI Data Input to SCK Edge
75
TdoR
SDO Data Output Rise Time
76
TdoF
SDO Data Output Fall Time
78
TscR
SCK Output Rise Time
(Master mode)
PIC18FXXXX
PIC18LFXXXX
PIC18FXXXX
PIC18LFXXXX
79
TscF
SCK Output Fall Time (Master mode)
—
25
ns
80
TscH2doV,
TscL2doV
SDO Data Output Valid after
SCK Edge
—
50
ns
100
ns
81
TdoV2scH,
TdoV2scL
SDO Data Output Setup to SCK Edge
—
ns
Note 1:
2:
PIC18FXXXX
PIC18LFXXXX
TCY
Conditions
(Note 1)
(Note 1)
(Note 2)
VDD = 2.0V
VDD = 2.0V
VDD = 2.0V
Requires the use of Parameter #73A.
Only if Parameter #71A and #72A are used.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 341
PIC18F2X1X/4X1X
FIGURE 25-15:
EXAMPLE SPI™ SLAVE MODE TIMING (CKE = 0)
SS
70
SCK
(CKP = 0)
83
71
72
78
79
79
78
SCK
(CKP = 1)
80
MSb
SDO
bit 6 - - - - - -1
LSb
77
75, 76
MSb In
SDI
73
Note:
bit 6 - - - -1
LSb In
74
Refer to Figure 25-5 for load conditions.
TABLE 25-16: EXAMPLE SPI™ MODE REQUIREMENTS (SLAVE MODE TIMING, CKE = 0)
Param
No.
Symbol
Characteristic
70
TssL2scH, SS ↓ to SCK ↓ or SCK ↑ Input
TssL2scL
71
TscH
71A
72
TscL
72A
Min
Max Units Conditions
TCY
—
SCK Input High Time
(Slave mode)
Continuous
1.25 TCY + 30
—
ns
Single Byte
40
—
ns
SCK Input Low Time
(Slave mode)
Continuous
1.25 TCY + 30
—
ns
Single Byte
40
—
ns
100
—
ns
73
TdiV2scH, Setup Time of SDI Data Input to SCK Edge
TdiV2scL
73A
Tb2b
74
TscH2diL, Hold Time of SDI Data Input to SCK Edge
TscL2diL
75
TdoR
Last Clock Edge of Byte 1 to the First Clock Edge of Byte 2 1.5 TCY + 40
SDO Data Output Rise Time
PIC18FXXXX
—
ns
100
—
ns
—
25
ns
45
ns
PIC18LFXXXX
76
TdoF
77
TssH2doZ SS↑ to SDO Output High-Impedance
78
TscR
SDO Data Output Fall Time
SCK Output Rise Time (Master mode)
PIC18FXXXX
—
25
ns
10
50
ns
—
25
ns
45
ns
—
25
ns
—
50
ns
100
ns
—
ns
PIC18LFXXXX
79
TscF
80
TscH2doV, SDO Data Output Valid after SCK Edge PIC18FXXXX
TscL2doV
PIC18LFXXXX
83
Note 1:
2:
ns
SCK Output Fall Time (Master mode)
TscH2ssH, SS ↑ after SCK edge
TscL2ssH
1.5 TCY + 40
(Note 1)
(Note 1)
(Note 2)
VDD = 2.0V
VDD = 2.0V
VDD = 2.0V
Requires the use of Parameter #73A.
Only if Parameter #71A and #72A are used.
DS39636A-page 342
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
FIGURE 25-16:
EXAMPLE SPI™ SLAVE MODE TIMING (CKE = 1)
82
SS
SCK
(CKP = 0)
70
83
71
72
SCK
(CKP = 1)
80
MSb
SDO
bit 6 - - - - - -1
LSb
75, 76
SDI
MSb In
Note:
77
bit 6 - - - -1
LSb In
74
Refer to Figure 25-5 for load conditions.
TABLE 25-17: EXAMPLE SPI™ SLAVE MODE REQUIREMENTS (CKE = 1)
Param
No.
Symbol
Characteristic
70
TssL2scH, SS ↓ to SCK ↓ or SCK ↑ Input
TssL2scL
71
TscH
71A
72
TscL
72A
Min
TCY
—
ns
SCK Input High Time
(Slave mode)
Continuous
1.25 TCY + 30
—
ns
Single Byte
40
—
ns
SCK Input Low Time
(Slave mode)
Continuous
1.25 TCY + 30
—
ns
Single Byte
40
—
ns
(Note 1)
(Note 2)
Last Clock Edge of Byte 1 to the First Clock Edge of Byte 2 1.5 TCY + 40
73A
Tb2b
74
TscH2diL, Hold Time of SDI Data Input to SCK Edge
TscL2diL
75
TdoR
SDO Data Output Rise Time
PIC18FXXXX
—
ns
100
—
ns
—
25
ns
45
ns
—
25
ns
10
50
ns
PIC18LFXXXX
76
TdoF
77
TssH2doZ SS↑ to SDO Output High-Impedance
78
TscR
SDO Data Output Fall Time
SCK Output Rise Time
(Master mode)
79
TscF
80
TscH2doV, SDO Data Output Valid after SCK
TscL2doV Edge
82
83
PIC18FXXXX
—
25
ns
PIC18LFXXXX
—
45
ns
SCK Output Fall Time (Master mode)
TssL2doV SDO Data Output Valid after SS ↓
Edge
—
25
ns
PIC18FXXXX
—
50
ns
PIC18LFXXXX
—
100
ns
PIC18FXXXX
—
50
ns
PIC18LFXXXX
—
100
ns
1.5 TCY + 40
—
ns
TscH2ssH, SS ↑ after SCK Edge
TscL2ssH
Note 1:
2:
Max Units Conditions
(Note 1)
VDD = 2.0V
VDD = 2.0V
VDD = 2.0V
VDD = 2.0V
Requires the use of Parameter #73A.
Only if Parameter #71A and #72A are used.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 343
PIC18F2X1X/4X1X
I2C™ BUS START/STOP BITS TIMING
FIGURE 25-17:
SCL
91
93
90
92
SDA
Stop
Condition
Start
Condition
Note:
Refer to Figure 25-5 for load conditions.
TABLE 25-18: I2C™ BUS START/STOP BITS REQUIREMENTS (SLAVE MODE)
Param.
Symbol
No.
90
91
92
93
TSU:STA
THD:STA
TSU:STO
Characteristic
Max
Units
Conditions
ns
Only relevant for Repeated
Start condition
ns
After this period, the first
clock pulse is generated
Start Condition
100 kHz mode
4700
—
Setup Time
400 kHz mode
600
—
Start Condition
100 kHz mode
4000
—
Hold Time
400 kHz mode
600
—
Stop Condition
100 kHz mode
4700
—
Setup Time
400 kHz mode
600
—
100 kHz mode
4000
—
400 kHz mode
600
—
THD:STO Stop Condition
Hold Time
FIGURE 25-18:
Min
ns
ns
I2C™ BUS DATA TIMING
103
102
100
101
SCL
90
106
107
91
92
SDA
In
110
109
109
SDA
Out
Note:
Refer to Figure 25-5 for load conditions.
DS39636A-page 344
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
TABLE 25-19: I2C™ BUS DATA REQUIREMENTS (SLAVE MODE)
Param.
Symbol
No.
100
THIGH
Characteristic
Clock High Time
100 kHz mode
400 kHz mode
TLOW
Clock Low Time
91
106
107
92
109
110
2:
µs
—
—
100 kHz mode
4.7
—
µs
400 kHz mode
1.3
—
µs
—
ns
20 + 0.1 CB
300
ns
100 kHz mode
—
300
ns
400 kHz mode
20 + 0.1 CB
300
ns
CB is specified to be from
10 to 400 pF
TSU:STA Start Condition
Setup Time
100 kHz mode
4.7
—
µs
400 kHz mode
0.6
—
µs
Only relevant for Repeated
Start condition
THD:STA Start Condition
Hold Time
100 kHz mode
4.0
—
µs
400 kHz mode
0.6
—
µs
THD:DAT Data Input Hold
Time
100 kHz mode
0
—
ns
400 kHz mode
0
0.9
µs
TSU:DAT Data Input Setup
Time
100 kHz mode
250
—
ns
400 kHz mode
100
—
ns
TSU:STO Stop Condition
Setup Time
100 kHz mode
4.7
—
µs
400 kHz mode
0.6
—
µs
TAA
100 kHz mode
—
3500
ns
400 kHz mode
—
—
ns
CB
Note 1:
µs
1000
TBUF
D102
—
—
TF
90
4.0
Conditions
1.5 TCY
TR
103
Units
0.6
SSP Module
102
Max
1.5 TCY
SSP Module
101
Min
SDA and SCL Rise 100 kHz mode
Time
400 kHz mode
SDA and SCL Fall
Time
Output Valid from
Clock
Bus Free Time
100 kHz mode
4.7
—
µs
400 kHz mode
1.3
—
µs
—
400
pF
Bus Capacitive Loading
CB is specified to be from
10 to 400 pF
After this period, the first
clock pulse is generated
(Note 2)
(Note 1)
Time the bus must be free
before a new transmission
can start
As a transmitter, the device must provide this internal minimum delay time to bridge the undefined region
(min. 300 ns) of the falling edge of SCL to avoid unintended generation of Start or Stop conditions.
A Fast mode I2C bus device can be used in a Standard mode I2C bus system, but the requirement
TSU:DAT ≥ 250 ns must then be met. This will automatically be the case if the device does not stretch the
LOW period of the SCL signal. If such a device does stretch the LOW period of the SCL signal, it must
output the next data bit to the SDA line, TR max. + TSU:DAT = 1000 + 250 = 1250 ns (according to the
standard mode I2C bus specification), before the SCL line is released.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 345
PIC18F2X1X/4X1X
MASTER SSP I2C™ BUS START/STOP BITS TIMING WAVEFORMS
FIGURE 25-19:
SCL
93
91
90
92
SDA
Stop
Condition
Start
Condition
Note:
Refer to Figure 25-5 for load conditions.
TABLE 25-20: MASTER SSP I2C™ BUS START/STOP BITS REQUIREMENTS
Param.
Symbol
No.
90
91
TSU:STA
Characteristic
ns
Only relevant for
Repeated Start
condition
ns
After this period, the
first clock pulse is
generated
100 kHz mode
2(TOSC)(BRG + 1)
—
400 kHz mode
2(TOSC)(BRG + 1)
—
1 MHz mode(1)
2(TOSC)(BRG + 1)
—
100 kHz mode
2(TOSC)(BRG + 1)
—
400 kHz mode
2(TOSC)(BRG + 1)
—
1 MHz mode(1)
2(TOSC)(BRG + 1)
—
100 kHz mode
2(TOSC)(BRG + 1)
—
400 kHz mode
2(TOSC)(BRG + 1)
—
1 MHz mode(1)
2(TOSC)(BRG + 1)
—
100 kHz mode
2(TOSC)(BRG + 1)
—
400 kHz mode
2(TOSC)(BRG + 1)
—
1 MHz mode(1)
2(TOSC)(BRG + 1)
—
THD:STA Start Condition
TSU:STO Stop Condition
THD:STO Stop Condition
Hold Time
Note 1: Maximum pin capacitance = 10 pF for all
FIGURE 25-20:
Units
Setup Time
Setup Time
93
Max
Start Condition
Hold Time
92
Min
I2C
Conditions
ns
ns
pins.
MASTER SSP I2C™ BUS DATA TIMING
103
102
100
101
SCL
90
106
91
107
92
SDA
In
109
109
110
SDA
Out
Note:
DS39636A-page 346
Refer to Figure 25-5 for load conditions.
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
TABLE 25-21: MASTER SSP I2C™ BUS DATA REQUIREMENTS
Param.
Symbol
No.
100
101
THIGH
TLOW
Characteristic
Min
Max
Units
2(TOSC)(BRG + 1)
—
ms
400 kHz mode
2(TOSC)(BRG + 1)
—
ms
1 MHz mode(1)
2(TOSC)(BRG + 1)
—
ms
Clock Low Time 100 kHz mode
2(TOSC)(BRG + 1)
—
ms
400 kHz mode
2(TOSC)(BRG + 1)
—
ms
(1)
Clock High Time 100 kHz mode
2(TOSC)(BRG + 1)
—
ms
100 kHz mode
—
1000
ns
400 kHz mode
20 + 0.1 CB
300
ns
1 MHz mode(1)
—
300
ns
1 MHz mode
102
103
90
91
TR
TF
TSU:STA
SDA and SCL
Rise Time
SDA and SCL
Fall Time
Start Condition
Setup Time
THD:STA Start Condition
Hold Time
100 kHz mode
—
300
ns
400 kHz mode
20 + 0.1 CB
300
ns
1 MHz mode(1)
—
100
ns
100 kHz mode
2(TOSC)(BRG + 1)
—
ms
400 kHz mode
2(TOSC)(BRG + 1)
—
ms
1 MHz mode(1)
2(TOSC)(BRG + 1)
—
ms
100 kHz mode
2(TOSC)(BRG + 1)
—
ms
400 kHz mode
2(TOSC)(BRG + 1)
—
ms
1 MHz mode(1)
2(TOSC)(BRG + 1)
—
ms
0
—
ns
106
THD:DAT Data Input
Hold Time
100 kHz mode
400 kHz mode
0
0.9
ms
107
TSU:DAT
100 kHz mode
250
—
ns
92
TSU:STO Stop Condition
Setup Time
109
110
D102
Note 1:
2:
TAA
TBUF
CB
Data Input
Setup Time
Output Valid
from Clock
Bus Free Time
400 kHz mode
100
—
ns
100 kHz mode
2(TOSC)(BRG + 1)
—
ms
400 kHz mode
2(TOSC)(BRG + 1)
—
ms
1 MHz mode(1)
2(TOSC)(BRG + 1)
—
ms
100 kHz mode
—
3500
ns
400 kHz mode
—
1000
ns
(1)
1 MHz mode
—
—
ns
100 kHz mode
4.7
—
ms
400 kHz mode
1.3
—
ms
—
400
pF
Bus Capacitive Loading
Conditions
CB is specified to be from
10 to 400 pF
CB is specified to be from
10 to 400 pF
Only relevant for
Repeated Start
condition
After this period, the first
clock pulse is generated
(Note 2)
Time the bus must be free
before a new transmission
can start
2C
Maximum pin capacitance = 10 pF for all I pins.
A Fast mode I2C bus device can be used in a Standard mode I2C bus system, but parameter 107 ≥ 250 ns
must then be met. This will automatically be the case if the device does not stretch the LOW period of the
SCL signal. If such a device does stretch the LOW period of the SCL signal, it must output the next data bit
to the SDA line, parameter 102 + parameter 107 = 1000 + 250 = 1250 ns (for 100 kHz mode), before the
SCL line is released.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 347
PIC18F2X1X/4X1X
FIGURE 25-21:
USART SYNCHRONOUS TRANSMISSION (MASTER/SLAVE) TIMING
RC6/TX/CK
pin
121
121
RC7/RX/DT
pin
120
Note:
122
Refer to Figure 25-5 for load conditions.
TABLE 25-22: USART SYNCHRONOUS TRANSMISSION REQUIREMENTS
Param
No.
120
Symbol
Characteristic
TckH2dtV SYNC XMIT (MASTER & SLAVE)
Clock High to Data Out Valid
PIC18FXXXX
Min
Max
Units
—
40
ns
PIC18LFXXXX
—
100
ns
121
Tckrf
Clock Out Rise Time and Fall Time
(Master mode)
PIC18FXXXX
—
20
ns
PIC18LFXXXX
—
50
ns
122
Tdtrf
Data Out Rise Time and Fall Time
PIC18FXXXX
—
20
ns
PIC18LFXXXX
—
50
ns
FIGURE 25-22:
RC6/TX/CK
pin
Conditions
VDD = 2.0V
VDD = 2.0V
VDD = 2.0V
USART SYNCHRONOUS RECEIVE (MASTER/SLAVE) TIMING
125
RC7/RX/DT
pin
126
Note:
Refer to Figure 25-5 for load conditions.
TABLE 25-23: USART SYNCHRONOUS RECEIVE REQUIREMENTS
Param.
No.
125
126
Symbol
TdtV2ckl
TckL2dtl
DS39636A-page 348
Characteristic
Min
Max
Units
SYNC RCV (MASTER & SLAVE)
Data Hold before CK ↓ (DT hold time)
10
—
ns
Data Hold after CK ↓ (DT hold time)
15
—
ns
Preliminary
Conditions
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
TABLE 25-24: A/D CONVERTER CHARACTERISTICS: PIC18F2X1X/4X1X (INDUSTRIAL)
PIC18LF2X1X/4X1X (INDUSTRIAL)
Param
Symbol
No.
Characteristic
Min
Typ
Max
Units
—
—
10
bit
Conditions
∆VREF ≥ 3.0V
A01
NR
Resolution
A03
EIL
Integral Linearity Error
—
—
<±1
LSb ∆VREF ≥ 3.0V
A04
EDL
Differential Linearity Error
—
—
<±1
LSb ∆VREF ≥ 3.0V
A06
EOFF
Offset Error
—
—
<±1
LSb ∆VREF ≥ 3.0V
A07
EGN
Gain Error
—
—
<±1
LSb ∆VREF ≥ 3.0V
A10
—
Monotonicity
—
VSS ≤ VAIN ≤ VREF
A20
∆VREF
Reference Voltage Range
(VREFH – VREFL)
1.8
3
—
—
—
—
V
V
VDD < 3.0V
VDD ≥ 3.0V
A21
VREFH
Reference Voltage High
VSS
—
VREFH
V
A22
VREFL
Reference Voltage Low
VSS – 0.3V
—
VDD – 3.0V
V
A25
VAIN
Analog Input Voltage
VREFL
—
VREFH
V
A30
ZAIN
Recommended Impedance of
Analog Voltage Source
—
—
2.5
kΩ
A50
IREF
VREF Input Current(2)
—
—
—
—
5
150
µA
µA
Note 1:
2:
Guaranteed(1)
During VAIN acquisition.
During A/D conversion
cycle.
The A/D conversion result never decreases with an increase in the input voltage and has no missing codes.
VREFH current is from RA3/AN3/VREF+ pin or VDD, whichever is selected as the VREFH source.
VREFL current is from RA2/AN2/VREF-/CVREF pin or VSS, whichever is selected as the VREFL source.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 349
PIC18F2X1X/4X1X
FIGURE 25-23:
A/D CONVERSION TIMING
BSF ADCON0, GO
(Note 2)
131
Q4
130
(1)
132
A/D CLK
9
A/D DATA
8
7
...
...
2
1
0
NEW_DATA
OLD_DATA
ADRES
TCY
ADIF
GO
DONE
SAMPLING STOPPED
SAMPLE
Note
1:
If the A/D clock source is selected as RC, a time of TCY is added before the A/D clock starts.
This allows the SLEEP instruction to be executed.
2:
This is a minimal RC delay (typically 100 ns), which also disconnects the holding capacitor from the analog input.
TABLE 25-25: A/D CONVERSION REQUIREMENTS
Param
Symbol
No.
130
TAD
Characteristic
A/D Clock Period
Min
Max
Units
PIC18FXXXX
0.7
25.0(1)
µs
TOSC based, VREF ≥ 3.0V
PIC18LFXXXX
1.4
25.0(1)
µs
VDD = 2.0V;
TOSC based, VREF full range
PIC18FXXXX
TBD
1
µs
A/D RC mode
PIC18LFXXXX
TBD
3
µs
VDD = 2.0V; A/D RC mode
11
12
TAD
1.4
TBD
—
—
µs
µs
131
TCNV
Conversion Time
(not including acquisition time) (Note 2)
132
TACQ
Acquisition Time (Note 3)
135
TSWC
Switching Time from Convert → Sample
—
(Note 4)
TBD
TDIS
Discharge Time
0.2
—
Legend:
Note 1:
2:
3:
4:
Conditions
-40°C to +85°C
0°C ≤ to ≤ +85°C
µs
TBD = To Be Determined
The time of the A/D clock period is dependent on the device frequency and the TAD clock divider.
ADRES register may be read on the following TCY cycle.
The time for the holding capacitor to acquire the “New” input voltage when the voltage changes full scale
after the conversion (VDD to VSS or VSS to VDD). The source impedance (RS) on the input channels is 50Ω.
On the following cycle of the device clock.
DS39636A-page 350
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
26.0
DC AND AC
CHARACTERISTICS GRAPHS
AND TABLES
Graphs and tables are not available at this time.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 351
PIC18F2X1X/4X1X
NOTES:
DS39636A-page 352
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
27.0
PACKAGING INFORMATION
27.1
Package Marking Information
28-Lead SPDIP
Example
PIC18F2610-I/SP
0410017
XXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXX
YYWWNNN
28-Lead SOIC
Example
XXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXX
YYWWNNN
28-Lead QFN
PIC18F2610-E/SO
0410017
Example
XXXXXXXX
XXXXXXXX
YYWWNNN
Legend: XX...X
Y
YY
WW
NNN
Note:
*
18F2510
-I/ML
0410017
Customer specific information*
Year code (last digit of calendar year)
Year code (last 2 digits of calendar year)
Week code (week of January 1 is week ‘01’)
Alphanumeric traceability code
In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line thus limiting the number of available characters
for customer specific information.
Standard PICmicro device marking consists of Microchip part number, year code, week code and
traceability code. For PICmicro device marking beyond this, certain price adders apply. Please check
with your Microchip Sales Office. For QTP devices, any special marking adders are included in QTP
price.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 353
PIC18F2X1X/4X1X
27.1
Package Marking Information (Continued)
40-Lead PDIP
Example
XXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXX
YYWWNNN
PIC18F4610-I/P
0410017
44-Lead QFN
Example
XXXXXXXXXX
XXXXXXXXXX
XXXXXXXXXX
YYWWNNN
PIC18F4610
-I/ML
0410017
44-Lead TQFP
Example
XXXXXXXXXX
XXXXXXXXXX
XXXXXXXXXX
YYWWNNN
DS39636A-page 354
PIC18F4610
-I/PT
0410017
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
27.2
Package Details
The following sections give the technical details of the
packages.
28-Lead Skinny Plastic Dual In-line (SP) – 300 mil Body (PDIP)
E1
D
2
n
1
α
E
A2
A
L
c
β
B1
A1
eB
Units
Number of Pins
Pitch
p
B
Dimension Limits
n
p
INCHES*
MIN
NOM
MILLIMETERS
MAX
MIN
NOM
28
MAX
28
.100
2.54
Top to Seating Plane
A
.140
.150
.160
3.56
3.81
4.06
Molded Package Thickness
A2
.125
.130
.135
3.18
3.30
3.43
8.26
Base to Seating Plane
A1
.015
Shoulder to Shoulder Width
E
.300
.310
.325
7.62
7.87
Molded Package Width
E1
.275
.285
.295
6.99
7.24
7.49
Overall Length
D
1.345
1.365
1.385
34.16
34.67
35.18
Tip to Seating Plane
L
c
.125
.130
.135
3.18
3.30
3.43
.008
.012
.015
0.20
0.29
0.38
B1
.040
.053
.065
1.02
1.33
1.65
Lead Thickness
Upper Lead Width
Lower Lead Width
Overall Row Spacing
Mold Draft Angle Top
Mold Draft Angle Bottom
§
0.38
B
.016
.019
.022
0.41
0.48
0.56
eB
α
.320
.350
.430
8.13
8.89
10.92
β
5
10
15
5
10
15
5
10
15
5
10
15
* Controlling Parameter
§ Significant Characteristic
Notes:
Dimension D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed
.010” (0.254mm) per side.
JEDEC Equivalent: MO-095
Drawing No. C04-070
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 355
PIC18F2X1X/4X1X
28-Lead Plastic Small Outline (SO) – Wide, 300 mil Body (SOIC)
E
E1
p
D
B
2
1
n
h
α
45°
c
A2
A
φ
β
L
Units
Dimension Limits
n
p
Number of Pins
Pitch
Overall Height
Molded Package Thickness
Standoff §
Overall Width
Molded Package Width
Overall Length
Chamfer Distance
Foot Length
Foot Angle Top
Lead Thickness
Lead Width
Mold Draft Angle Top
Mold Draft Angle Bottom
* Controlling Parameter
§ Significant Characteristic
A
A2
A1
E
E1
D
h
L
φ
c
B
α
β
A1
MIN
.093
.088
.004
.394
.288
.695
.010
.016
0
.009
.014
0
0
INCHES*
NOM
28
.050
.099
.091
.008
.407
.295
.704
.020
.033
4
.011
.017
12
12
MAX
.104
.094
.012
.420
.299
.712
.029
.050
8
.013
.020
15
15
MILLIMETERS
NOM
28
1.27
2.36
2.50
2.24
2.31
0.10
0.20
10.01
10.34
7.32
7.49
17.65
17.87
0.25
0.50
0.41
0.84
0
4
0.23
0.28
0.36
0.42
0
12
0
12
MIN
MAX
2.64
2.39
0.30
10.67
7.59
18.08
0.74
1.27
8
0.33
0.51
15
15
Notes:
Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed
.010” (0.254mm) per side.
JEDEC Equivalent: MS-013
Drawing No. C04-052
DS39636A-page 356
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
28-Lead Plastic Quad Flat No Lead Package (ML) 6x6 mm Body (QFN) –
With 0.55 mm Contact Length (Saw Singulated)
E
E2
EXPOSED
METAL
PAD
e
D
D2
b
2
1
n
OPTIONAL
INDEX
AREA
TOP VIEW
ALTERNATE
INDEX
INDICATORS
SEE DETAIL
L
BOTTOM VIEW
A1
A
DETAIL
ALTERNATE
PAD OUTLINE
Number of Pins
Pitch
Overall Height
Standoff
Contact Thickness
Overall Width
Exposed Pad Width
Overall Length
Exposed Pad Length
Contact Width
Contact Length
Units
Dimension Limits
n
e
A
A1
A3
E
E2
D
D2
b
L
MIN
.031
.000
.232
.140
.232
.140
.009
.020
INCHES
NOM
28
.026 BSC
.035
.001
.008 REF
.236
.146
.236
.146
.011
.024
MAX
MIN
.039
.002
0.80
0.00
.240
.152
.240
.152
.013
.028
5.90
3.55
5.90
3.55
0.23
0.50
MILLIMETERS*
NOM
28
0.65 BSC
0.90
0.02
0.20 REF
6.00
3.70
6.00
3.70
0.28
0.60
MAX
1.00
0.05
6.10
3.85
6.10
3.85
0.33
0.70
*Controlling Parameter
Notes:
JEDEC equivalent: MO-220
Drawing No. C04-105
 2004 Microchip Technology Inc.
Revised 05-24-04
Preliminary
DS39636A-page 357
PIC18F2X1X/4X1X
40-Lead Plastic Dual In-line (P) – 600 mil Body (PDIP)
E1
D
α
2
1
n
E
A2
A
L
c
β
B1
A1
eB
p
B
Units
Dimension Limits
n
p
MIN
INCHES*
NOM
40
.100
.175
.150
MAX
MILLIMETERS
NOM
40
2.54
4.06
4.45
3.56
3.81
0.38
15.11
15.24
13.46
13.84
51.94
52.26
3.05
3.30
0.20
0.29
0.76
1.27
0.36
0.46
15.75
16.51
5
10
5
10
MIN
Number of Pins
Pitch
Top to Seating Plane
A
.160
.190
Molded Package Thickness
A2
.140
.160
Base to Seating Plane
.015
A1
Shoulder to Shoulder Width
E
.595
.600
.625
Molded Package Width
E1
.530
.545
.560
Overall Length
D
2.045
2.058
2.065
Tip to Seating Plane
L
.120
.130
.135
c
Lead Thickness
.008
.012
.015
Upper Lead Width
B1
.030
.050
.070
Lower Lead Width
B
.014
.018
.022
Overall Row Spacing
§
eB
.620
.650
.680
α
Mold Draft Angle Top
5
10
15
β
Mold Draft Angle Bottom
5
10
15
* Controlling Parameter
§ Significant Characteristic
Notes:
Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed
.010” (0.254mm) per side.
JEDEC Equivalent: MO-011
Drawing No. C04-016
DS39636A-page 358
Preliminary
MAX
4.83
4.06
15.88
14.22
52.45
3.43
0.38
1.78
0.56
17.27
15
15
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
44-Lead Plastic Quad Flat No Lead Package (ML) 8x8 mm Body (QFN)
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 359
PIC18F2X1X/4X1X
44-Lead Plastic Thin Quad Flatpack (PT) 10x10x1 mm Body, 1.0/0.10 mm Lead Form (TQFP)
E
E1
#leads=n1
p
D1
D
2
1
B
n
CH x 45 °
α
A
c
φ
β
L
A1
A2
(F)
Units
Dimension Limits
n
p
Number of Pins
Pitch
Pins per Side
Overall Height
Molded Package Thickness
Standoff §
Foot Length
Footprint (Reference)
Foot Angle
Overall Width
Overall Length
Molded Package Width
Molded Package Length
Lead Thickness
Lead Width
Pin 1 Corner Chamfer
Mold Draft Angle Top
Mold Draft Angle Bottom
* Controlling Parameter
§ Significant Characteristic
n1
A
A2
A1
L
(F)
φ
E
D
E1
D1
c
B
CH
α
β
MIN
.039
.037
.002
.018
0
.463
.463
.390
.390
.004
.012
.025
5
5
INCHES
NOM
44
.031
11
.043
.039
.004
.024
.039
3.5
.472
.472
.394
.394
.006
.015
.035
10
10
MAX
.047
.041
.006
.030
7
.482
.482
.398
.398
.008
.017
.045
15
15
MILLIMETERS*
NOM
44
0.80
11
1.00
1.10
0.95
1.00
0.05
0.10
0.45
0.60
1.00
0
3.5
11.75
12.00
11.75
12.00
9.90
10.00
9.90
10.00
0.09
0.15
0.30
0.38
0.64
0.89
5
10
5
10
MIN
MAX
1.20
1.05
0.15
0.75
7
12.25
12.25
10.10
10.10
0.20
0.44
1.14
15
15
Notes:
Dimensions D1 and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed
.010” (0.254mm) per side.
JEDEC Equivalent: MS-026
Drawing No. C04-076
DS39636A-page 360
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
APPENDIX A:
REVISION HISTORY
APPENDIX B:
Revision A (June 2004)
Original data sheet for PIC18F2X1X/4X1X devices.
TABLE B-1:
DEVICE
DIFFERENCES
The differences between the devices listed in this data
sheet are shown in Table B-1 and Table B-2.
DEVICE DIFFERENCES (PIC18F2410/2510/2515/2610)
Features
PIC18F2410
PIC18F2510
PIC18F2515
PIC18F2610
Program Memory (Bytes)
16384
32768
49152
65536
Program Memory (Instructions)
8192
16384
24576
32768
Interrupt Sources
18
18
18
18
Ports A, B, C, (E)
Ports A, B, C, (E)
Ports A, B, C, (E)
Ports A, B, C, (E)
Capture/Compare/PWM Modules
2
2
2
2
Enhanced
Capture/Compare/PWM Modules
0
0
0
0
No
No
No
No
10 input channels
10 input channels
10 input channels
10 input channels
28-pin SPDIP
28-pin SOIC
28-pin QFN
28-pin SPDIP
28-pin SOIC
28-pin QFN
28-pin SPDIP
28-pin SOIC
28-pin SPDIP
28-pin SOIC
I/O Ports
Parallel
Communications (PSP)
10-bit Analog-to-Digital Module
Packages
TABLE B-2:
DEVICE DIFFERENCES (PIC18F4410/4510/4515/4610)
Features
PIC18F4410
PIC18F4510
PIC18F4515
PIC18F4610
Program Memory (Bytes)
16384
32768
49152
65536
Program Memory (Instructions)
8192
16384
24576
32768
19
19
19
19
Ports A, B, C, D, E
Ports A, B, C, D, E
Ports A, B, C, D, E
Ports A, B, C, D, E
Capture/Compare/PWM Modules
2
2
2
2
Enhanced
Capture/Compare/PWM Modules
0
0
0
0
Yes
Yes
Yes
Yes
13 input channels
13 input channels
13 input channels
13 input channels
40-pin PDIP
44-pin QFN
44-pin TQFP
40-pin PDIP
44-pin QFN
44-pin TQFP
40-pin PDIP
44-pin QFN
44-pin TQFP
40-pin PDIP
44-pin QFN
44-pin TQFP
Interrupt Sources
I/O Ports
Parallel
Communications (PSP)
10-bit Analog-to-Digital Module
Packages
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 361
PIC18F2X1X/4X1X
APPENDIX C:
CONVERSION
CONSIDERATIONS
APPENDIX D:
This appendix discusses the considerations for
converting from previous versions of a device to the
ones listed in this data sheet. Typically, these changes
are due to the differences in the process technology
used. An example of this type of conversion is from a
PIC16C74A to a PIC16C74B.
Not Applicable
DS39636A-page 362
MIGRATION FROM
BASELINE TO
ENHANCED DEVICES
This section discusses how to migrate from a Baseline
device (i.e., PIC16C5X) to an Enhanced MCU device
(i.e., PIC18FXXX).
The following are the list of modifications over the
PIC16C5X microcontroller family:
Not Currently Available
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
APPENDIX E:
MIGRATION FROM
MID-RANGE TO
ENHANCED DEVICES
A detailed discussion of the differences between the
mid-range MCU devices (i.e., PIC16CXXX) and the
enhanced devices (i.e., PIC18FXXX) is provided in
AN716, “Migrating Designs from PIC16C74A/74B to
PIC18C442.” The changes discussed, while device
specific, are generally applicable to all mid-range to
enhanced device migrations.
APPENDIX F:
MIGRATION FROM
HIGH-END TO
ENHANCED DEVICES
A detailed discussion of the migration pathway and
differences between the high-end MCU devices (i.e.,
PIC17CXXX) and the enhanced devices (i.e.,
PIC18FXXX) is provided in AN726, “PIC17CXXX to
PIC18CXXX Migration.” This Application Note is
available as Literature Number DS00726.
This Application Note is available as Literature Number
DS00716.
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 363
PIC18F2X1X/4X1X
NOTES:
DS39636A-page 364
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
INDEX
A
A/D ................................................................................... 211
A/D Converter Interrupt, Configuring ....................... 215
Acquisition Requirements ........................................ 216
ADCON0 Register .................................................... 211
ADCON1 Register .................................................... 211
ADCON2 Register .................................................... 211
ADRESH Register ............................................ 211, 214
ADRESL Register .................................................... 211
Analog Port Pins, Configuring .................................. 218
Associated Registers ............................................... 220
Calculating the Minimum Required
Acquisition Time .............................................. 216
Configuring the Module ............................................ 215
Conversion Clock (TAD) ........................................... 217
Conversion Status (GO/DONE Bit) .......................... 214
Conversions ............................................................. 219
Converter Characteristics ........................................ 349
Operation in Power Managed Modes ...................... 218
Selecting and Configuring
Acquisition Time .............................................. 217
Special Event Trigger (CCP) .................................... 220
Special Event Trigger (ECCP) ................................. 138
Use of the CCP2 Trigger .......................................... 220
Absolute Maximum Ratings ............................................. 313
AC (Timing) Characteristics ............................................. 331
Load Conditions for Device
Timing Specifications ....................................... 332
Parameter Symbology ............................................. 331
Temperature and Voltage Specifications ................. 332
Timing Conditions .................................................... 332
AC Characteristics
Internal RC Accuracy ............................................... 334
Access Bank
Mapping with Indexed Literal Offset
Addressing Mode ............................................... 73
ACKSTAT ........................................................................ 181
ACKSTAT Status Flag ..................................................... 181
ADCON0 Register ............................................................ 211
GO/DONE Bit ........................................................... 214
ADCON1 Register ............................................................ 211
ADCON2 Register ............................................................ 211
ADDFSR .......................................................................... 300
ADDLW ............................................................................ 263
ADDULNK ........................................................................ 300
ADDWF ............................................................................ 263
ADDWFC ......................................................................... 264
ADRESH Register ............................................................ 211
ADRESL Register .................................................... 211, 214
Analog-to-Digital Converter. See A/D.
ANDLW ............................................................................ 264
ANDWF ............................................................................ 265
Assembler
MPASM Assembler .................................................. 307
Auto-Wake-up on Sync Break Character ......................... 204
B
Bank Select Register (BSR) ............................................... 59
Baud Rate Generator ....................................................... 177
BC .................................................................................... 265
BCF .................................................................................. 266
BF .................................................................................... 181
BF Status Flag ................................................................. 181
 2004 Microchip Technology Inc.
Block Diagrams
A/D ........................................................................... 214
Analog Input Model .................................................. 215
Baud Rate Generator .............................................. 177
Capture Mode Operation ......................................... 131
Comparator Analog Input Model .............................. 225
Comparator I/O Operating Modes (Diagram) .......... 222
Comparator Output .................................................. 224
Comparator Voltage Reference ............................... 228
Comparator Voltage Reference
Output Buffer Example .................................... 229
Compare Mode Operation ....................................... 132
Device Clock .............................................................. 28
Enhanced PWM ....................................................... 139
EUSART Receive .................................................... 202
EUSART Transmit ................................................... 200
External Power-on Reset Circuit
(Slow VDD Power-up) ........................................ 43
Fail-Safe Clock Monitor ........................................... 249
Generic I/O Port ......................................................... 95
High/Low-Voltage Detect with External Input .......... 232
Interrupt Logic ............................................................ 82
MSSP (I2C Master Mode) ........................................ 175
MSSP (I2C Mode) .................................................... 160
MSSP (SPI Mode) ................................................... 151
On-Chip Reset Circuit ................................................ 41
PIC18F2410/2510/2515/2610 ................................... 11
PIC18F4410/4510/4515/4610 ................................... 12
PLL (HS Mode) .......................................................... 25
PORTD and PORTE
(Parallel Slave Port) ......................................... 110
PWM Operation (Simplified) .................................... 134
Reads from Flash Program Memory ......................... 76
Single Comparator ................................................... 223
Table Read Operation ............................................... 75
Timer0 in 16-Bit Mode ............................................. 114
Timer0 in 8-Bit Mode ............................................... 114
Timer1 ..................................................................... 118
Timer1 (16-Bit Read/Write Mode) ............................ 118
Timer2 ..................................................................... 124
Timer3 ..................................................................... 126
Timer3 (16-Bit Read/Write Mode) ............................ 126
Watchdog Timer ...................................................... 246
BN .................................................................................... 266
BNC ................................................................................. 267
BNN ................................................................................. 267
BNOV .............................................................................. 268
BNZ ................................................................................. 268
BOR. See Brown-out Reset.
BOV ................................................................................. 271
BRA ................................................................................. 269
Break Character (12-Bit) Transmit
and Receive ............................................................. 205
BRG. See Baud Rate Generator.
Brown-out Reset (BOR) ..................................................... 44
Detecting ................................................................... 44
Disabling in Sleep Mode ............................................ 44
Software Enabled ...................................................... 44
BSF .................................................................................. 269
BTFSC ............................................................................. 270
BTFSS ............................................................................. 270
BTG ................................................................................. 271
BZ .................................................................................... 272
Preliminary
DS39636A-page 365
PIC18F2X1X/4X1X
C
C Compilers
MPLAB C17 ............................................................. 308
MPLAB C18 ............................................................. 308
MPLAB C30 ............................................................. 308
CALL ................................................................................ 272
CALLW ............................................................................. 301
Capture (CCP Module) ..................................................... 131
Associated Registers ............................................... 133
CCP Pin Configuration ............................................. 131
CCPRxH:CCPRxL Registers ................................... 131
Prescaler .................................................................. 131
Software Interrupt .................................................... 131
Timer1/Timer3 Mode Selection ................................ 131
Capture (ECCP Module) .................................................. 138
Capture/Compare/PWM (CCP) ........................................ 129
Capture Mode. See Capture.
CCP Mode and Timer Resources ............................ 130
CCPRxH Register .................................................... 130
CCPRxL Register ..................................................... 130
Compare Mode. See Compare.
Interaction of Two CCP Modules ............................. 130
Module Configuration ............................................... 130
Clock Sources .................................................................... 28
Selecting the 31 kHz Source ...................................... 29
Selection Using OSCCON Register ........................... 29
CLRF ................................................................................ 273
CLRWDT .......................................................................... 273
Code Examples
16 x 16 Signed Multiply Routine ................................ 80
16 x 16 Unsigned Multiply Routine ............................ 80
8 x 8 Signed Multiply Routine .................................... 79
8 x 8 Unsigned Multiply Routine ................................ 79
Changing Between Capture Prescalers ................... 131
Computed GOTO Using an Offset Value ................... 56
Fast Register Stack .................................................... 56
How to Clear RAM (Bank 1)
Using Indirect Addressing .................................. 69
Implementing a Real-Time Clock
Using a Timer1 Interrupt Service ..................... 121
Initializing PORTA ...................................................... 95
Initializing PORTB ...................................................... 98
Initializing PORTC .................................................... 101
Initializing PORTD .................................................... 104
Initializing PORTE .................................................... 107
Loading the SSPBUF (SSPSR) Register ................. 154
Reading a Flash Program Memory Word .................. 77
Saving Status, WREG and
BSR Registers in RAM ....................................... 93
Code Protection ............................................................... 237
COMF ............................................................................... 274
Comparator ...................................................................... 221
Analog Input Connection Considerations ................. 225
Associated Registers ............................................... 225
Configuration ............................................................ 222
Effects of a Reset ..................................................... 224
Interrupts .................................................................. 224
Operation ................................................................. 223
Operation During Sleep ........................................... 224
Outputs .................................................................... 223
Reference ................................................................ 223
External Signal ................................................. 223
Internal Signal .................................................. 223
Response Time ........................................................ 223
Comparator Specifications ............................................... 329
DS39636A-page 366
Comparator Voltage Reference ....................................... 227
Accuracy and Error .................................................. 228
Associated Registers ............................................... 229
Configuring .............................................................. 227
Connection Considerations ...................................... 228
Effects of a Reset .................................................... 228
Operation During Sleep ........................................... 228
Compare (CCP Module) .................................................. 132
Associated Registers ............................................... 133
CCPRx Register ...................................................... 132
Pin Configuration ..................................................... 132
Software Interrupt .................................................... 132
Special Event Trigger .............................. 127, 132, 220
Timer1/Timer3 Mode Selection ................................ 132
Compare (ECCP Module) ................................................ 138
Special Event Trigger .............................................. 138
Computed GOTO ............................................................... 56
Configuration Bits ............................................................ 237
Configuration Register Protection .................................... 255
Context Saving During Interrupts ....................................... 93
Conversion Considerations .............................................. 362
CPFSEQ .......................................................................... 274
CPFSGT .......................................................................... 275
CPFSLT ........................................................................... 275
Crystal Oscillator/Ceramic Resonator ................................ 23
D
Data Addressing Modes .................................................... 69
Comparing Addressing Modes with
the Extended Instruction Set Enabled ............... 72
Direct ......................................................................... 69
Indexed Literal Offset ................................................ 71
Indirect ....................................................................... 69
Inherent and Literal .................................................... 69
Data Memory ..................................................................... 59
Access Bank .............................................................. 63
and the Extended Instruction Set .............................. 71
Bank Select Register (BSR) ...................................... 59
General Purpose Registers ....................................... 63
Map for PIC18F2410/4410 ........................................ 60
Map for PIC18F2510/4510 ........................................ 61
Map for PIC18F2515/2610/4515/4610 ...................... 62
Special Function Registers ........................................ 64
DAW ................................................................................ 276
DC and AC Characteristics
Graphs and Tables .................................................. 351
DC Characteristics ........................................................... 326
Power-Down and Supply Current ............................ 317
Supply Voltage ........................................................ 316
DCFSNZ .......................................................................... 277
DECF ............................................................................... 276
DECFSZ .......................................................................... 277
Demonstration Boards
PICDEM 1 ................................................................ 310
PICDEM 17 .............................................................. 311
PICDEM 18R ........................................................... 311
PICDEM 2 Plus ........................................................ 310
PICDEM 3 ................................................................ 310
PICDEM 4 ................................................................ 310
PICDEM LIN ............................................................ 311
PICDEM USB .......................................................... 311
PICDEM.net Internet/Ethernet ................................. 310
Development Support ...................................................... 307
Device Differences ........................................................... 361
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
Device Overview .................................................................. 7
Details on Individual Family Members ......................... 8
New Core Features ...................................................... 7
Other Special Features ................................................ 8
Device Overview (PIC18F2410/2510/2515/2610)
Features (table) ............................................................ 9
Device Overview (PIC18F4410/4510/4515/4610)
Features (table) .......................................................... 10
Device Reset Timers .......................................................... 45
Oscillator Start-up Timer (OST) ................................. 45
PLL Lock Time-out ..................................................... 45
Power-up Timer (PWRT) ........................................... 45
Direct Addressing ............................................................... 70
E
Effect on Standard PIC Instructions ........................... 71, 304
Effects of Power Managed Modes on
Various Clock Sources ............................................... 31
Electrical Characteristics .................................................. 313
Enhanced Capture/Compare/PWM (ECCP) .................... 137
Capture and Compare Modes .................................. 138
Capture Mode. See Capture (ECCP Module).
Outputs and Configuration ....................................... 138
Pin Configurations for ECCP1 ................................. 138
PWM Mode. See PWM (ECCP Module).
Standard PWM Mode ............................................... 138
Timer Resources ...................................................... 138
Enhanced PWM Mode. See PWM (ECCP Module).
Enhanced Universal Synchronous
Asynchronous Receiver Transmitter
(EUSART). See EUSART.
Equations
A/D Acquisition Time ................................................ 216
A/D Minimum Charging Time ................................... 216
Errata ................................................................................... 6
EUSART
Asynchronous Mode ................................................ 200
12-Bit Break Transmit and Receive ................. 205
Associated Registers, Receive ........................ 203
Associated Registers, Transmit ....................... 201
Auto-Wake-up on Sync Break ......................... 204
Receiver ........................................................... 202
Setting up 9-bit Mode with
Address Detect ........................................ 202
Transmitter ....................................................... 200
Baud Rate Generator
Operation in Power Managed Mode ................ 195
Baud Rate Generator (BRG) .................................... 195
Associated Registers ....................................... 195
Auto-Baud Rate Detect .................................... 198
Baud Rate Error, Calculating ........................... 195
Baud Rates, Asynchronous Modes ................. 196
High Baud Rate Select (BRGH Bit) ................. 195
Sampling .......................................................... 195
Synchronous Master Mode ...................................... 206
Associated Registers, Receive ........................ 208
Associated Registers, Transmit ....................... 207
Reception ......................................................... 208
Transmission ................................................... 206
Synchronous Slave Mode ........................................ 209
Associated Registers, Receive ........................ 210
Associated Registers, Transmit ....................... 209
Reception ......................................................... 210
Transmission ................................................... 209
 2004 Microchip Technology Inc.
Evaluation and Programming Tools ................................. 311
Extended Instruction Set ................................................. 299
ADDFSR .................................................................. 300
ADDULNK ............................................................... 300
and Using MPLAB Tools ......................................... 306
CALLW .................................................................... 301
Considerations for Use ............................................ 304
MOVSF .................................................................... 301
MOVSS .................................................................... 302
PUSHL ..................................................................... 302
SUBFSR .................................................................. 303
SUBULNK ................................................................ 303
Syntax ...................................................................... 299
External Clock Input ........................................................... 24
F
Fail-Safe Clock Monitor ........................................... 237, 249
Interrupts in Power Managed Modes ....................... 250
POR or Wake from Sleep ........................................ 250
WDT During Oscillator Failure ................................. 249
Fast Register Stack ........................................................... 56
Flash Program Memory ..................................................... 75
Associated Registers ................................................. 77
Control Registers ....................................................... 76
Reading ..................................................................... 76
TABLAT (Table Latch) Register ................................ 76
Table Reads and Table Writes .................................. 75
TBLPTR (Table Pointer) Register .............................. 76
FSCM. See Fail-Safe Clock Monitor.
G
General Call Address Support ......................................... 174
GOTO .............................................................................. 278
H
Hardware Multiplier ............................................................ 79
Introduction ................................................................ 79
Operation ................................................................... 79
Performance Comparison .......................................... 79
High/Low-Voltage Detect ................................................. 231
Applications ............................................................. 234
Associated Registers ............................................... 235
Characteristics ......................................................... 330
Current Consumption .............................................. 233
Effects of a Reset .................................................... 235
Operation ................................................................. 232
During Sleep .................................................... 235
Setup ....................................................................... 233
Start-up Time ........................................................... 233
Typical Application ................................................... 234
HLVD. See High/Low-Voltage Detect.
I
I/O Ports ............................................................................ 95
I2C Mode (MSSP)
Acknowledge Sequence Timing .............................. 184
Baud Rate Generator .............................................. 177
Bus Collision
During a Repeated Start Condition .................. 188
During a Stop Condition .................................. 189
Clock Arbitration ...................................................... 178
Clock Stretching ...................................................... 170
10-Bit Slave Receive Mode (SEN = 1) ............ 170
10-Bit Slave Transmit Mode ............................ 170
7-Bit Slave Receive Mode (SEN = 1) .............. 170
7-Bit Slave Transmit Mode .............................. 170
Preliminary
DS39636A-page 367
PIC18F2X1X/4X1X
Clock Synchronization and the
CKP bit (SEN = 1) ............................................ 171
Effects of a Reset ..................................................... 185
General Call Address Support ................................. 174
I2C Clock Rate w/BRG ............................................. 177
Master Mode ............................................................ 175
Operation ......................................................... 176
Reception ......................................................... 181
Repeated Start Timing ..................................... 180
Start Condition Timing ..................................... 179
Transmission .................................................... 181
Multi-Master Communication, Bus Collision
and Arbitration .................................................. 185
Multi-Master Mode ................................................... 185
Operation ................................................................. 164
Read/Write Bit Information (R/W Bit) ............... 164, 165
Registers .................................................................. 160
Serial Clock (RC3/SCK/SCL) ................................... 165
Slave Mode .............................................................. 164
Addressing ....................................................... 164
Reception ......................................................... 165
Transmission .................................................... 165
Sleep Operation ....................................................... 185
Stop Condition Timing .............................................. 184
ID Locations ............................................................. 237, 255
INCF ................................................................................. 278
INCFSZ ............................................................................ 279
In-Circuit Debugger .......................................................... 255
In-Circuit Serial Programming (ICSP) ...................... 237, 255
Indexed Literal Offset Addressing
and Standard PIC18 Instructions ............................. 304
Indexed Literal Offset Mode ....................................... 71, 304
Indirect Addressing ............................................................ 70
INFSNZ ............................................................................ 279
Initialization Conditions for all Registers ...................... 49–52
Instruction Cycle ................................................................. 57
Clocking Scheme ....................................................... 57
Instruction Flow/Pipelining ................................................. 57
Instruction Set
ADDLW .................................................................... 263
ADDWF .................................................................... 263
ADDWF (Indexed Literal Offset mode) .................... 305
ADDWFC ................................................................. 264
ANDLW .................................................................... 264
ANDWF .................................................................... 265
BC ............................................................................ 265
BCF .......................................................................... 266
BN ............................................................................ 266
BNC ......................................................................... 267
BNN ......................................................................... 267
BNOV ....................................................................... 268
BNZ .......................................................................... 268
BOV ......................................................................... 271
BRA .......................................................................... 269
BSF .......................................................................... 269
BSF (Indexed Literal Offset mode) .......................... 305
BTFSC ..................................................................... 270
BTFSS ..................................................................... 270
BTG .......................................................................... 271
BZ ............................................................................ 272
CALL ........................................................................ 272
CLRF ........................................................................ 273
CLRWDT .................................................................. 273
DS39636A-page 368
COMF ...................................................................... 274
CPFSEQ .................................................................. 274
CPFSGT .................................................................. 275
CPFSLT ................................................................... 275
DAW ........................................................................ 276
DCFSNZ .................................................................. 277
DECF ....................................................................... 276
DECFSZ .................................................................. 277
Firmware Instructions .............................................. 257
General Format ........................................................ 259
GOTO ...................................................................... 278
INCF ........................................................................ 278
INCFSZ .................................................................... 279
INFSNZ .................................................................... 279
IORLW ..................................................................... 280
IORWF ..................................................................... 280
LFSR ....................................................................... 281
MOVF ...................................................................... 281
MOVFF .................................................................... 282
MOVLB .................................................................... 282
MOVLW ................................................................... 283
MOVWF ................................................................... 283
MULLW .................................................................... 284
MULWF .................................................................... 284
NEGF ....................................................................... 285
NOP ......................................................................... 285
Opcode Field Descriptions ....................................... 258
POP ......................................................................... 286
PUSH ....................................................................... 286
RCALL ..................................................................... 287
RESET ..................................................................... 287
RETFIE .................................................................... 288
RETLW .................................................................... 288
RETURN .................................................................. 289
RLCF ....................................................................... 289
RLNCF ..................................................................... 290
RRCF ....................................................................... 290
RRNCF .................................................................... 291
SETF ....................................................................... 291
SETF (Indexed Literal Offset mode) ........................ 305
SLEEP ..................................................................... 292
Standard Instructions ............................................... 257
SUBFWB ................................................................. 292
SUBLW .................................................................... 293
SUBWF .................................................................... 293
SUBWFB ................................................................. 294
SWAPF .................................................................... 294
TBLRD ..................................................................... 295
TBLWT .................................................................... 296
TSTFSZ ................................................................... 297
XORLW ................................................................... 297
XORWF ................................................................... 298
INTCON Registers ....................................................... 83–85
Inter-Integrated Circuit. See I2C.
Internal Oscillator Block ..................................................... 26
Adjustment ................................................................. 26
INTIO Modes ............................................................. 26
INTOSC Frequency Drift ............................................ 26
INTOSC Output Frequency ....................................... 26
OSCTUNE Register ................................................... 26
PLL in INTOSC Modes .............................................. 26
Internal RC Oscillator
Use with WDT .......................................................... 246
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
Interrupt Sources ............................................................. 237
A/D Conversion Complete ....................................... 215
Capture Complete (CCP) ......................................... 131
Compare Complete (CCP) ....................................... 132
Interrupt-on-Change (RB7:RB4) ................................ 98
INTn Pin ..................................................................... 93
PORTB, Interrupt-on-Change .................................... 93
TMR0 ......................................................................... 93
TMR0 Overflow ........................................................ 115
TMR1 Overflow ........................................................ 117
TMR2 to PR2 Match (PWM) ............................ 134, 139
TMR3 Overflow ................................................ 125, 127
Interrupts ............................................................................ 81
Interrupts, Flag Bits
Interrupt-on-Change (RB7:RB4)
Flag (RBIF Bit) ................................................... 98
INTOSC, INTRC. See Internal Oscillator Block.
IORLW ............................................................................. 280
IORWF ............................................................................. 280
IPR Registers ..................................................................... 90
L
LFSR ................................................................................ 281
Low-Voltage ICSP Programming.
See Single-Supply ICSP Programming.
M
Master Clear (MCLR) ......................................................... 43
Master Synchronous Serial Port (MSSP). See MSSP.
Memory Organization ......................................................... 53
Data Memory ............................................................. 59
Program Memory ....................................................... 53
Memory Programming Requirements .............................. 328
Migration from Baseline to
Enhanced Devices ................................................... 362
Migration from High-End to
Enhanced Devices ................................................... 363
Migration from Mid-Range to
Enhanced Devices ................................................... 363
MOVF ............................................................................... 281
MOVFF ............................................................................ 282
MOVLB ............................................................................ 282
MOVLW ........................................................................... 283
MOVSF ............................................................................ 301
MOVSS ............................................................................ 302
MOVWF ........................................................................... 283
MPLAB ASM30 Assembler, Linker, Librarian .................. 308
MPLAB ICD 2 In-Circuit Debugger .................................. 309
MPLAB ICE 2000 High-Performance
Universal In-Circuit Emulator ................................... 309
MPLAB ICE 4000 High-Performance
Universal In-Circuit Emulator ................................... 309
MPLAB Integrated Development
Environment Software .............................................. 307
MPLAB PM3 Device Programmer ................................... 309
MPLINK Object Linker/MPLIB Object Librarian ............... 308
MSSP
ACK Pulse ........................................................ 164, 165
Control Registers (general) ...................................... 151
I2C Mode. See I2C Mode.
Module Overview ..................................................... 151
SPI Master/Slave Connection .................................. 155
SPI Mode. See SPI Mode.
SSPBUF ................................................................... 156
SSPSR ..................................................................... 156
 2004 Microchip Technology Inc.
MULLW ............................................................................ 284
MULWF ............................................................................ 284
N
NEGF ............................................................................... 285
NOP ................................................................................. 285
O
OPTION_REG Register
PSA Bit .................................................................... 115
T0CS Bit .................................................................. 114
T0PS2:T0PS0 Bits ................................................... 115
T0SE Bit .................................................................. 114
Oscillator Configuration ..................................................... 23
EC .............................................................................. 23
ECIO .......................................................................... 23
HS .............................................................................. 23
HSPLL ....................................................................... 23
Internal Oscillator Block ............................................. 26
INTIO1 ....................................................................... 23
INTIO2 ....................................................................... 23
LP .............................................................................. 23
RC ............................................................................. 23
RCIO .......................................................................... 23
XT .............................................................................. 23
Oscillator Selection .......................................................... 237
Oscillator Start-up Timer (OST) ................................... 31, 45
Oscillator Switching ........................................................... 28
Oscillator Transitions ......................................................... 29
Oscillator, Timer1 ..................................................... 117, 127
Oscillator, Timer3 ............................................................. 125
P
Packaging Information ..................................................... 353
Details (Diagrams) ................................................... 355
Marking .................................................................... 353
Parallel Slave Port (PSP) ......................................... 104, 110
Associated Registers ............................................... 111
CS (Chip Select) ...................................................... 110
PORTD .................................................................... 110
RD (Read Input) ...................................................... 110
Select (PSPMODE Bit) .................................... 104, 110
WR (Write Input) ...................................................... 110
PICkit 1 Flash Starter Kit ................................................. 311
PICSTART Plus Development Programmer .................... 310
PIE Registers ..................................................................... 88
Pin Functions
MCLR/VPP/RE3 ................................................... 13, 17
OSC1/CLKI/RA7 .................................................. 13, 17
OSC2/CLKO/RA6 ................................................ 13, 17
RA0/AN0 .............................................................. 14, 18
RA1/AN1 .............................................................. 14, 18
RA2/AN2/VREF-/CVREF ....................................... 14, 18
RA3/AN3/VREF+ .................................................. 14, 18
RA4/T0CKI/C1OUT ............................................. 14, 18
RA5/AN4/SS/HLVDIN/C2OUT ............................ 14, 18
RB0/INT0/FLT0/AN12 ......................................... 15, 19
RB1/INT1/AN10 ................................................... 15, 19
RB2/INT2/AN8 ..................................................... 15, 19
RB3/AN9/CCP2 ................................................... 15, 19
RB4/KBI0/AN11 ................................................... 15, 19
RB5/KBI1/PGM .................................................... 15, 19
RB6/KBI2/PGC .................................................... 15, 19
RB7/KBI3/PGD .................................................... 15, 19
RC0/T1OSO/T13CKI ........................................... 16, 20
Preliminary
DS39636A-page 369
PIC18F2X1X/4X1X
RC1/T1OSI/CCP2 ................................................ 16, 20
RC2/CCP1 ................................................................. 16
RC2/CCP1/P1A ......................................................... 20
RC3/SCK/SCL ..................................................... 16, 20
RC4/SDI/SDA ...................................................... 16, 20
RC5/SDO ............................................................. 16, 20
RC6/TX/CK .......................................................... 16, 20
RC7/RX/DT .......................................................... 16, 20
RD0/PSP0 .................................................................. 21
RD1/PSP1 .................................................................. 21
RD2/PSP2 .................................................................. 21
RD3/PSP3 .................................................................. 21
RD4/PSP4 .................................................................. 21
RD5/PSP5/P1B .......................................................... 21
RD6/PSP6/P1C .......................................................... 21
RD7/PSP7/P1D .......................................................... 21
RE0/RD/AN5 .............................................................. 22
RE1/WR/AN6 ............................................................. 22
RE2/CS/AN7 .............................................................. 22
VDD ....................................................................... 16, 22
VSS ....................................................................... 16, 22
Pinout I/O Descriptions
PIC18F2410/2510/2515/2610 .................................... 13
PIC18F4410/4510/4515/4610 .................................... 17
PIR Registers ..................................................................... 86
PLL Frequency Multiplier ................................................... 25
HSPLL Oscillator Mode .............................................. 25
Use with INTOSC ....................................................... 25
POP .................................................................................. 286
POR. See Power-on Reset.
PORTA
Associated Registers ................................................. 97
LATA Register ............................................................ 95
PORTA Register ........................................................ 95
TRISA Register .......................................................... 95
PORTB
Associated Registers ............................................... 100
LATB Register ............................................................ 98
PORTB Register ........................................................ 98
RB7:RB4 Interrupt-on-Change Flag
(RBIF Bit) ........................................................... 98
TRISB Register .......................................................... 98
PORTC
Associated Registers ............................................... 103
LATC Register ......................................................... 101
PORTC Register ...................................................... 101
RC3/SCK/SCL Pin ................................................... 165
TRISC Register ........................................................ 101
PORTD
Associated Registers ............................................... 106
LATD Register ......................................................... 104
Parallel Slave Port (PSP) Function .......................... 104
PORTD Register ...................................................... 104
TRISD Register ........................................................ 104
PORTE
Associated Registers ............................................... 109
LATE Register .......................................................... 107
PORTE Register ...................................................... 107
PSP Mode Select (PSPMODE Bit) .......................... 104
TRISE Register ........................................................ 107
Postscaler, WDT
Assignment (PSA Bit) .............................................. 115
Rate Select (T0PS2:T0PS0 Bits) ............................. 115
Switching Between Timer0 and WDT ...................... 115
DS39636A-page 370
Power Managed Modes ..................................................... 33
and A/D Operation ................................................... 218
and EUSART Operation .......................................... 195
and Multiple Sleep Commands .................................. 34
and PWM Operation ................................................ 149
and SPI Operation ................................................... 159
Clock Sources ............................................................ 33
Clock Transitions and Status Indicators .................... 34
Effects on Clock Sources ........................................... 31
Entering ..................................................................... 33
Exiting Idle and Sleep Modes .................................... 39
by Interrupt ........................................................ 39
by Reset ............................................................ 39
by WDT Time-out .............................................. 39
Without a Start-up Delay ................................... 40
Idle Modes ................................................................. 37
PRI_IDLE ........................................................... 38
RC_IDLE ........................................................... 39
SEC_IDLE ......................................................... 38
Run Modes ................................................................ 34
PRI_RUN ........................................................... 34
RC_RUN ............................................................ 35
SEC_RUN ......................................................... 34
Selecting .................................................................... 33
Sleep Mode ............................................................... 37
Summary (table) ........................................................ 33
Power-on Reset (POR) ...................................................... 43
Power-up Timer (PWRT) ........................................... 45
Time-out Sequence ................................................... 45
Power-up Delays ............................................................... 31
Power-up Timer (PWRT) ................................................... 31
Prescaler
Timer2 ..................................................................... 140
Prescaler, Timer0 ............................................................ 115
Assignment (PSA Bit) .............................................. 115
Rate Select (T0PS2:T0PS0 Bits) ............................. 115
Switching Between Timer0 and WDT ...................... 115
Prescaler, Timer2 ............................................................ 135
PRI_IDLE Mode ................................................................. 38
PRI_RUN Mode ................................................................. 34
PRO MATE II Universal Device Programmer .................. 309
Program Counter ............................................................... 54
PCL, PCH and PCU Registers .................................. 54
PCLATH and PCLATU Registers .............................. 54
Program Memory
and Extended Instruction Set .................................... 73
Code Protection ....................................................... 253
Instructions ................................................................ 58
Two-Word .......................................................... 58
Interrupt Vector .......................................................... 53
Look-up Tables .......................................................... 56
Map and Stack (diagram) .......................................... 53
Reset Vector .............................................................. 53
Program Verification and Code Protection ...................... 251
Associated Registers ............................................... 252
Programming, Device Instructions ................................... 257
PSP. See Parallel Slave Port.
Pulse-Width Modulation. See PWM (
CCP Module) and PWM (ECCP Module).
PUSH ............................................................................... 286
PUSH and POP Instructions .............................................. 55
PUSHL ............................................................................. 302
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
PWM (CCP Module)
Associated Registers ............................................... 136
Auto-Shutdown (CCP1 only) .................................... 135
CCPR1H:CCPR1L Registers ................................... 139
Duty Cycle ........................................................ 134, 140
Example Frequencies/Resolutions .................. 135, 140
Period ............................................................... 134, 139
Setup for PWM Operation ........................................ 135
TMR2 to PR2 Match ........................................ 134, 139
PWM (ECCP Module) ...................................................... 139
Associated Registers ............................................... 150
Direction Change in Full-Bridge
Output Mode .................................................... 144
Effects of a Reset ..................................................... 149
Enhanced PWM Auto-Shutdown ............................. 146
Full-Bridge Application Example .............................. 144
Full-Bridge Mode ...................................................... 143
Half-Bridge Mode ..................................................... 142
Half-Bridge Output Mode
Applications Example ...................................... 142
Operation in Power Managed Modes ...................... 149
Operation with Fail-Safe Clock Monitor ................... 149
Output Configurations .............................................. 140
Output Relationships (Active-High) .......................... 141
Output Relationships (Active-Low) ........................... 141
Programmable Dead-Band Delay ............................ 146
Setup for PWM Operation ........................................ 149
Start-up Considerations ........................................... 148
Q
Q Clock .................................................................... 135, 140
R
RAM. See Data Memory.
RBIF Bit .............................................................................. 98
RC Oscillator ...................................................................... 25
RCIO Oscillator Mode ................................................ 25
RC_IDLE Mode .................................................................. 39
RC_RUN Mode .................................................................. 35
RCALL ............................................................................. 287
RCON Register
Bit Status During Initialization .................................... 48
Register File ....................................................................... 63
Registers
ADCON0 (A/D Control 0) ......................................... 211
ADCON1 (A/D Control 1) ......................................... 212
ADCON2 (A/D Control 2) ......................................... 213
BAUDCON (Baud Rate Control) .............................. 194
CCP1CON (Enhanced
Capture/Compare/PWM Control 1) .................. 137
CCPxCON (Standard
Capture/Compare/PWM Control) ..................... 129
CMCON (Comparator Control) ................................ 221
CONFIG1H (Configuration 1 High) .......................... 238
CONFIG2H (Configuration 2 High) .......................... 240
CONFIG2L (Configuration 2 Low) ............................ 239
CONFIG3H (Configuration 3 High) .......................... 241
CONFIG4L (Configuration 4 Low) ............................ 241
CONFIG5H (Configuration 5 High) .......................... 242
CONFIG5L (Configuration 5 Low) ............................ 242
CONFIG6H (Configuration 6 High) .......................... 243
CONFIG6L (Configuration 6 Low) ............................ 243
CONFIG7H (Configuration 7 High) .......................... 244
CONFIG7L (Configuration 7 Low) ............................ 244
CVRCON (Comparator
Voltage Reference Control) ............................. 227
 2004 Microchip Technology Inc.
Device ID Register 1 ................................................ 245
Device ID Register 2 ................................................ 245
ECCP1AS (ECCP Auto-Shutdown
Control) ............................................................ 147
HLVDCON (HLVD Control) ..................................... 231
INTCON (Interrupt Control) ....................................... 83
INTCON2 (Interrupt Control 2) .................................. 84
INTCON3 (Interrupt Control 3) .................................. 85
IPR1 (Peripheral Interrupt Priority 1) ......................... 90
IPR2 (Peripheral Interrupt Priority 2) ......................... 91
OSCCON (Oscillator Control) .................................... 30
OSCTUNE (Oscillator Tuning) ................................... 27
PIE1 (Peripheral Interrupt Enable 1) ......................... 88
PIE2 (Peripheral Interrupt Enable 2) ......................... 89
PIR1 (Peripheral Interrupt
Request (Flag) 1) ............................................... 86
PIR2 (Peripheral Interrupt
Request (Flag) 2) ............................................... 87
PWM1CON (PWM Configuration) ........................... 146
RCON (Reset Control) ......................................... 42, 92
RCSTA (Receive Status and Control) ..................... 193
SSPCON1 (MSSP Control 1, I2C Mode) ................. 162
SSPCON1 (MSSP Control 1, SPI Mode) ................ 153
SSPCON2 (MSSP Control 2, I2C Mode) ................. 163
SSPSTAT (MSSP Status, I2C Mode) ...................... 161
SSPSTAT (MSSP Status, SPI Mode) ...................... 152
Status ........................................................................ 68
STKPTR (Stack Pointer) ............................................ 55
T0CON (Timer0 Control) ......................................... 113
T1CON (Timer1 Control) ......................................... 117
T2CON (Timer 2 Control) ........................................ 123
T3CON (Timer3 Control) ......................................... 125
TRISE (PORTE/PSP Control) ................................. 108
TXSTA (Transmit Status and Control) ..................... 192
WDTCON (Watchdog Timer Control) ...................... 247
RESET ............................................................................. 287
Reset State of Registers .................................................... 48
Resets ....................................................................... 41, 237
Brown-out Reset (BOR) ........................................... 237
Oscillator Start-up Timer (OST) ............................... 237
Power-on Reset (POR) ............................................ 237
Power-up Timer (PWRT) ......................................... 237
RETFIE ............................................................................ 288
RETLW ............................................................................ 288
RETURN .......................................................................... 289
Return Address Stack ........................................................ 54
Return Stack Pointer (STKPTR) ........................................ 55
Revision History ............................................................... 361
RLCF ............................................................................... 289
RLNCF ............................................................................. 290
RRCF ............................................................................... 290
RRNCF ............................................................................ 291
S
SCK ................................................................................. 151
SDI ................................................................................... 151
SDO ................................................................................. 151
SEC_IDLE Mode ............................................................... 38
SEC_RUN Mode ................................................................ 34
Serial Clock, SCK ............................................................ 151
Serial Data In (SDI) .......................................................... 151
Serial Data Out (SDO) ..................................................... 151
Serial Peripheral Interface. See SPI Mode.
SETF ............................................................................... 291
Single-Supply ICSP Programming.
Slave Select (SS) ............................................................. 151
Preliminary
DS39636A-page 371
PIC18F2X1X/4X1X
SLEEP .............................................................................. 292
Sleep
OSC1 and OSC2 Pin States ...................................... 31
Software Simulator (MPLAB SIM) .................................... 308
Software Simulator (MPLAB SIM30) ................................ 308
Special Event Trigger.
See Compare (ECCP Mode).
Special Event Trigger.
See Compare (ECCP Module).
Special Features of the CPU ............................................ 237
Special Function Registers ................................................ 64
Map ............................................................................ 64
SPI Mode (MSSP)
Associated Registers ............................................... 159
Bus Mode Compatibility ........................................... 159
Effects of a Reset ..................................................... 159
Enabling SPI I/O ...................................................... 155
Master Mode ............................................................ 156
Master/Slave Connection ......................................... 155
Operation ................................................................. 154
Operation in Power
Managed Modes .............................................. 159
Serial Clock .............................................................. 151
Serial Data In ........................................................... 151
Serial Data Out ........................................................ 151
Slave Mode .............................................................. 157
Slave Select ............................................................. 151
Slave Select Synchronization .................................. 157
SPI Clock ................................................................. 156
Typical Connection .................................................. 155
SS .................................................................................... 151
SSPOV ............................................................................. 181
SSPOV Status Flag .......................................................... 181
SSPSTAT Register
R/W Bit ............................................................. 164, 165
Stack Full/Underflow Resets .............................................. 56
SUBFSR ........................................................................... 303
SUBFWB .......................................................................... 292
SUBLW ............................................................................ 293
SUBULNK ........................................................................ 303
SUBWF ............................................................................ 293
SUBWFB .......................................................................... 294
SWAPF ............................................................................ 294
T
Table Pointer Operations (table) ........................................ 76
Table Reads/Table Writes .................................................. 56
TBLRD ............................................................................. 295
TBLWT ............................................................................. 296
Time-out in Various Situations (table) ................................ 45
Timer0 .............................................................................. 113
16-Bit Mode Timer Reads and Writes ...................... 114
Associated Registers ............................................... 115
Clock Source Edge Select
(T0SE Bit) ........................................................ 114
Clock Source Select (T0CS Bit) ............................... 114
Operation ................................................................. 114
Overflow Interrupt .................................................... 115
Prescaler .................................................................. 115
Prescaler. See Prescaler, Timer0.
DS39636A-page 372
Timer1 .............................................................................. 117
16-Bit Read/Write Mode .......................................... 119
Associated Registers ............................................... 121
Interrupt ................................................................... 120
Operation ................................................................. 118
Oscillator .......................................................... 117, 119
Oscillator Layout Considerations ............................. 120
Overflow Interrupt .................................................... 117
Resetting, Using the CCP
Special Event Trigger ...................................... 120
Special Event Trigger (ECCP) ................................. 138
TMR1H Register ...................................................... 117
TMR1L Register ....................................................... 117
Use as a Real-Time Clock ....................................... 120
Timer2 .............................................................................. 123
Associated Registers ............................................... 124
Interrupt ................................................................... 124
Operation ................................................................. 123
Output ...................................................................... 124
PR2 Register ................................................... 134, 139
TMR2 to PR2 Match Interrupt .......................... 134, 139
Timer3 .............................................................................. 125
16-Bit Read/Write Mode .......................................... 127
Associated Registers ............................................... 127
Operation ................................................................. 126
Oscillator .......................................................... 125, 127
Overflow Interrupt ............................................ 125, 127
Special Event Trigger (CCP) ................................... 127
TMR3H Register ...................................................... 125
TMR3L Register ....................................................... 125
Timing Diagrams
A/D Conversion ........................................................ 350
Acknowledge Sequence .......................................... 184
Asynchronous Reception ......................................... 203
Asynchronous Transmission .................................... 201
Asynchronous Transmission
(Back to Back) ................................................. 201
Automatic Baud Rate Calculation ............................ 199
Auto-Wake-up Bit (WUE) During
Normal Operation ............................................ 204
Auto-Wake-up Bit (WUE) During Sleep ................... 204
Baud Rate Generator with Clock Arbitration ............ 178
BRG Overflow Sequence ......................................... 199
BRG Reset Due to SDA Arbitration
During Start Condition ..................................... 187
Brown-out Reset (BOR) ........................................... 336
Bus Collision During a Repeated
Start Condition (Case 1) .................................. 188
Bus Collision During a Repeated
Start Condition (Case 2) .................................. 188
Bus Collision During a Start Condition
(SCL = 0) ......................................................... 187
Bus Collision During a Start Condition
(SDA only) ....................................................... 186
Bus Collision During a Stop Condition
(Case 1) ........................................................... 189
Bus Collision During a Stop Condition
(Case 2) ........................................................... 189
Bus Collision for Transmit and Acknowledge .......... 185
Capture/Compare/PWM (CCP) ............................... 338
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
CLKO and I/O .......................................................... 335
Clock Synchronization ............................................. 171
Clock/Instruction Cycle .............................................. 57
Example SPI Master Mode (CKE = 0) ..................... 340
Example SPI Master Mode (CKE = 1) ..................... 341
Example SPI Slave Mode (CKE = 0) ....................... 342
Example SPI Slave Mode (CKE = 1) ....................... 343
External Clock (All Modes except PLL) .................... 333
Fail-Safe Clock Monitor ............................................ 250
First Start Bit Timing ................................................ 179
Full-Bridge PWM Output .......................................... 143
Half-Bridge PWM Output ......................................... 142
High/Low-Voltage Detect Characteristics ................ 330
High-Voltage Detect (VDIRMAG = 1) ...................... 234
I2C Bus Data ............................................................ 344
I2C Bus Start/Stop Bits ............................................. 344
I2C Master Mode (7 or
10-Bit Transmission) ........................................ 182
I2C Master Mode (7-Bit Reception) .......................... 183
I2C Slave Mode (10-Bit Reception,
SEN = 0) .......................................................... 168
I2C Slave Mode (10-Bit Reception,
SEN = 1) .......................................................... 173
I2C Slave Mode (10-Bit Transmission) ..................... 169
I2C Slave Mode (7-Bit Reception,
SEN = 0) .......................................................... 166
I2C Slave Mode (7-Bit Reception,
SEN = 1) .......................................................... 172
I2C Slave Mode (7-Bit Transmission) ....................... 167
I2C Slave Mode General Call Address
Sequence (7 or 10-Bit Address Mode) ............ 174
I2C Stop Condition Receive or
Transmit Mode ................................................. 184
Low-Voltage Detect (VDIRMAG = 0) ....................... 233
Master SSP I2C Bus Data ........................................ 346
Master SSP I2C Bus Start/Stop Bits ........................ 346
Parallel Slave Port
(PIC18F4410/4510/4515/4610) ....................... 339
Parallel Slave Port (PSP) Read ............................... 111
Parallel Slave Port (PSP) Write ............................... 111
PWM Auto-Shutdown (PRSEN = 0,
Auto-Restart Disabled) .................................... 148
PWM Auto-Shutdown (PRSEN = 1,
Auto-Restart Enabled) ..................................... 148
PWM Direction Change ........................................... 145
PWM Direction Change at Near
100% Duty Cycle ............................................. 145
PWM Output ............................................................ 134
Repeat Start Condition ............................................. 180
Reset, Watchdog Timer (WDT),
Oscillator Start-up Timer (OST),
Power-up Timer (PWRT) ................................. 336
Send Break Character Sequence ............................ 205
Slave Synchronization ............................................. 157
Slow Rise Time (MCLR Tied to VDD,
VDD Rise > TPWRT) ............................................ 47
SPI Mode (Master Mode) ......................................... 156
SPI Mode (Slave Mode, CKE = 0) ........................... 158
SPI Mode (Slave Mode, CKE = 1) ........................... 158
Synchronous Reception
(Master Mode, SREN) ..................................... 208
 2004 Microchip Technology Inc.
Synchronous Transmission ..................................... 206
Synchronous Transmission
(Through TXEN) .............................................. 207
Time-out Sequence on POR w/PLL
Enabled (MCLR Tied to VDD) ............................ 47
Time-out Sequence on Power-up
(MCLR Not Tied to VDD, Case 1) ...................... 46
Time-out Sequence on Power-up
(MCLR Not Tied to VDD, Case 2) ...................... 46
Time-out Sequence on Power-up
(MCLR Tied to VDD, VDD Rise < TPWRT) ........... 46
Timer0 and Timer1 External Clock .......................... 337
Transition for Entry to Idle Mode ............................... 38
Transition for Entry to SEC_RUN Mode .................... 35
Transition for Entry to Sleep Mode ............................ 37
Transition for Two-Speed Start-up
(INTOSC to HSPLL) ........................................ 248
Transition for Wake from Idle to
Run Mode .......................................................... 38
Transition for Wake from Sleep (HSPLL) .................. 37
Transition from RC_RUN Mode to
PRI_RUN Mode ................................................. 36
Transition from SEC_RUN Mode to
PRI_RUN Mode (HSPLL) .................................. 35
Transition to RC_RUN Mode ..................................... 36
USART Synchronous Receive
(Master/Slave) ................................................. 348
USART Synchronous Transmission
(Master/Slave) ................................................. 348
Timing Diagrams and Specifications ............................... 333
A/D Conversion Requirements ................................ 350
Capture/Compare/PWM (CCP)
Requirements .................................................. 338
CLKO and I/O Requirements ................................... 335
Example SPI Mode Requirements
(Master Mode, CKE = 0) .................................. 340
Example SPI Mode Requirements
(Master Mode, CKE = 1) .................................. 341
Example SPI Mode Requirements
(Slave Mode, CKE = 0) .................................... 342
Example SPI Mode Requirements
(Slave Mode, CKE = 1) .................................... 343
External Clock Requirements .................................. 333
I2C Bus Data Requirements
(Slave Mode) ................................................... 345
Master SSP I2C Bus Data Requirements ................ 347
Master SSP I2C Bus Start/Stop Bits
Requirements .................................................. 346
Parallel Slave Port Requirements
(PIC18F4410/4510/4515/4610) ....................... 339
PLL Clock ................................................................ 334
Reset, Watchdog Timer,
Oscillator Start-up Timer,
Power-up Timer and
Brown-out Reset Requirements ...................... 336
Timer0 and Timer1 External
Clock Requirements ........................................ 337
USART Synchronous
Receive Requirements .................................... 348
USART Synchronous
Transmission Requirements ............................ 348
Preliminary
DS39636A-page 373
PIC18F2X1X/4X1X
Top-of-Stack Access .......................................................... 54
TRISE Register
PSPMODE Bit .......................................................... 104
TSTFSZ ............................................................................ 297
Two-Speed Start-up ................................................. 237, 248
Two-Word Instructions
Example Cases .......................................................... 58
TXSTA Register
BRGH Bit ................................................................. 195
V
Watchdog Timer (WDT) ........................................... 237, 246
Associated Registers ............................................... 247
Control Register ....................................................... 246
During Oscillator Failure .......................................... 249
Programming Considerations .................................. 246
WCOL ...................................................... 179, 180, 181, 184
WCOL Status Flag ................................... 179, 180, 181, 184
WWW, On-Line Support ...................................................... 6
X
Voltage Reference Specifications .................................... 329
DS39636A-page 374
W
XORLW ............................................................................ 297
XORWF ........................................................................... 298
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
ON-LINE SUPPORT
Microchip provides on-line support on the Microchip
World Wide Web site.
The web site is used by Microchip as a means to make
files and information easily available to customers. To
view the site, the user must have access to the Internet
and a web browser, such as Netscape® or Microsoft®
Internet Explorer. Files are also available for FTP
download from our FTP site.
SYSTEMS INFORMATION AND
UPGRADE HOT LINE
The Systems Information and Upgrade Line provides
system users a listing of the latest versions of all of
Microchip’s development systems software products.
Plus, this line provides information on how customers
can receive the most current upgrade kits.The Hot Line
Numbers are:
1-800-755-2345 for U.S. and most of Canada and
1-480-792-7302 for the rest of the world.
Connecting to the Microchip Internet
Web Site
042003
The Microchip web site is available at the following
URL:
www.microchip.com
The file transfer site is available by using an FTP
service to connect to:
ftp://ftp.microchip.com
The web site and file transfer site provide a variety of
services. Users may download files for the latest
Development Tools, Data Sheets, Application Notes,
User’s Guides, Articles and Sample Programs. A variety of Microchip specific business information is also
available, including listings of Microchip sales offices,
distributors and factory representatives. Other data
available for consideration is:
• Latest Microchip Press Releases
• Technical Support Section with Frequently Asked
Questions
• Design Tips
• Device Errata
• Job Postings
• Microchip Consultant Program Member Listing
• Links to other useful web sites related to
Microchip Products
• Conferences for products, Development Systems,
technical information and more
• Listing of seminars and events
 2004 Microchip Technology Inc.
Preliminary
DS39636A-page 375
PIC18F2X1X/4X1X
READER RESPONSE
It is our intention to provide you with the best documentation possible to ensure successful use of your Microchip product. If you wish to provide your comments on organization, clarity, subject matter and ways in which our documentation
can better serve you, please FAX your comments to the Technical Publications Manager at (480) 792-4150.
Please list the following information and use this outline to provide us with your comments about this document.
To:
Technical Publications Manager
RE:
Reader Response
Total Pages Sent ________
From: Name
Company
Address
City / State / ZIP / Country
Telephone: (_______) _________ - _________
FAX: (______) _________ - _________
Application (optional):
Would you like a reply?
Y
Device: PIC18F2X1X/4X1X
N
Literature Number: DS39636A
Questions:
1. What are the best features of this document?
2. How does this document meet your hardware and software development needs?
3. Do you find the organization of this document easy to follow? If not, why?
4. What additions to the document do you think would enhance the structure and subject?
5. What deletions from the document could be made without affecting the overall usefulness?
6. Is there any incorrect or misleading information (what and where)?
7. How would you improve this document?
DS39636A-page 376
Preliminary
 2004 Microchip Technology Inc.
PIC18F2X1X/4X1X
PIC18F2X1X/4X1X PRODUCT IDENTIFICATION SYSTEM
To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office.
PART NO.
X
/XX
XXX
Device
Temperature
Range
Package
Pattern
Examples:
a)
b)
Device
PIC18F2410/2510/2515/2610(1),
PIC18F4410/4510/4515/4610(1),
PIC18F2410/2510/2515/2610T(2),
PIC18F4410/4510/4515/4610 T(2);
VDD range 4.2V to 5.5V
PIC18LF2410/2510/2515/2610(1),
PIC18LF4410/4510/4515/4610(1),
PIC18LF2410/2510/2515/2610T(2),
PIC18LF4410/4510/4515/4610T(2);
VDD range 2.0V to 5.5V
Temperature Range
I
E
=
=
Package
PT
SO
SP
P
ML
=
=
=
=
=
Pattern
QTP, SQTP, Code or Special Requirements
(blank otherwise)
c)
-40°C to +85°C (Industrial)
-40°C to +125°C (Extended)
PIC18LF4510-I/P 301 = Industrial temp., PDIP
package, Extended VDD limits, QTP pattern
#301.
PIC18LF2410-I/SO = Industrial temp., SOIC
package, Extended VDD limits.
PIC18F4410-I/P = Industrial temp., PDIP
package, normal VDD limits.
Note 1:
2:
TQFP (Thin Quad Flatpack)
SOIC
Skinny Plastic DIP
PDIP
QFN
 2004 Microchip Technology Inc.
Preliminary
F = Standard Voltage Range
LF = Wide Voltage Range
T = in tape and reel TQFP
packages only.
DS39636A-page 377
Worldwide Sales and Service
AMERICAS
China - Beijing
Korea
Corporate Office
Unit 706B
Wan Tai Bei Hai Bldg.
No. 6 Chaoyangmen Bei Str.
Beijing, 100027, China
Tel: 86-10-85282100
Fax: 86-10-85282104
168-1, Youngbo Bldg. 3 Floor
Samsung-Dong, Kangnam-Ku
Seoul, Korea 135-882
Tel: 82-2-554-7200 Fax: 82-2-558-5932 or
82-2-558-5934
China - Chengdu
200 Middle Road
#07-02 Prime Centre
Singapore, 188980
Tel: 65-6334-8870 Fax: 65-6334-8850
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-792-7200
Fax: 480-792-7277
Technical Support: 480-792-7627
Web Address: www.microchip.com
3780 Mansell Road, Suite 130
Alpharetta, GA 30022
Tel: 770-640-0034
Fax: 770-640-0307
Rm. 2401-2402, 24th Floor,
Ming Xing Financial Tower
No. 88 TIDU Street
Chengdu 610016, China
Tel: 86-28-86766200
Fax: 86-28-86766599
Boston
China - Fuzhou
2 Lan Drive, Suite 120
Westford, MA 01886
Tel: 978-692-3848
Fax: 978-692-3821
Unit 28F, World Trade Plaza
No. 71 Wusi Road
Fuzhou 350001, China
Tel: 86-591-7503506
Fax: 86-591-7503521
Atlanta
Chicago
333 Pierce Road, Suite 180
Itasca, IL 60143
Tel: 630-285-0071
Fax: 630-285-0075
Dallas
4570 Westgrove Drive, Suite 160
Addison, TX 75001
Tel: 972-818-7423
Fax: 972-818-2924
Detroit
Tri-Atria Office Building
32255 Northwestern Highway, Suite 190
Farmington Hills, MI 48334
Tel: 248-538-2250
Fax: 248-538-2260
Kokomo
2767 S. Albright Road
Kokomo, IN 46902
Tel: 765-864-8360
Fax: 765-864-8387
Los Angeles
18201 Von Karman, Suite 1090
Irvine, CA 92612
Tel: 949-263-1888
Fax: 949-263-1338
San Jose
1300 Terra Bella Avenue
Mountain View, CA 94043
Tel: 650-215-1444
Fax: 650-961-0286
Toronto
6285 Northam Drive, Suite 108
Mississauga, Ontario L4V 1X5, Canada
Tel: 905-673-0699
Fax: 905-673-6509
ASIA/PACIFIC
Australia
Suite 22, 41 Rawson Street
Epping 2121, NSW
Australia
Tel: 61-2-9868-6733
Fax: 61-2-9868-6755
China - Hong Kong SAR
Unit 901-6, Tower 2, Metroplaza
223 Hing Fong Road
Kwai Fong, N.T., Hong Kong
Tel: 852-2401-1200
Fax: 852-2401-3431
Singapore
Taiwan
Kaohsiung Branch
30F - 1 No. 8
Min Chuan 2nd Road
Kaohsiung 806, Taiwan
Tel: 886-7-536-4818
Fax: 886-7-536-4803
Taiwan
Taiwan Branch
11F-3, No. 207
Tung Hua North Road
Taipei, 105, Taiwan
Tel: 886-2-2717-7175 Fax: 886-2-2545-0139
EUROPE
China - Shanghai
Austria
Room 701, Bldg. B
Far East International Plaza
No. 317 Xian Xia Road
Shanghai, 200051
Tel: 86-21-6275-5700
Fax: 86-21-6275-5060
Durisolstrasse 2
A-4600 Wels
Austria
Tel: 43-7242-2244-399
Fax: 43-7242-2244-393
Denmark
China - Shenzhen
Regus Business Centre
Lautrup hoj 1-3
Ballerup DK-2750 Denmark
Tel: 45-4420-9895 Fax: 45-4420-9910
Rm. 1812, 18/F, Building A, United Plaza
No. 5022 Binhe Road, Futian District
Shenzhen 518033, China
Tel: 86-755-82901380
Fax: 86-755-8295-1393
China - Shunde
Room 401, Hongjian Building, No. 2
Fengxiangnan Road, Ronggui Town, Shunde
District, Foshan City, Guangdong 528303, China
Tel: 86-757-28395507 Fax: 86-757-28395571
China - Qingdao
Rm. B505A, Fullhope Plaza,
No. 12 Hong Kong Central Rd.
Qingdao 266071, China
Tel: 86-532-5027355 Fax: 86-532-5027205
India
Divyasree Chambers
1 Floor, Wing A (A3/A4)
No. 11, O’Shaugnessey Road
Bangalore, 560 025, India
Tel: 91-80-22290061 Fax: 91-80-22290062
Japan
Benex S-1 6F
3-18-20, Shinyokohama
Kohoku-Ku, Yokohama-shi
Kanagawa, 222-0033, Japan
Tel: 81-45-471- 6166 Fax: 81-45-471-6122
France
Parc d’Activite du Moulin de Massy
43 Rue du Saule Trapu
Batiment A - ler Etage
91300 Massy, France
Tel: 33-1-69-53-63-20
Fax: 33-1-69-30-90-79
Germany
Steinheilstrasse 10
D-85737 Ismaning, Germany
Tel: 49-89-627-144-0
Fax: 49-89-627-144-44
Italy
Via Quasimodo, 12
20025 Legnano (MI)
Milan, Italy
Tel: 39-0331-742611
Fax: 39-0331-466781
Netherlands
Waegenburghtplein 4
NL-5152 JR, Drunen, Netherlands
Tel: 31-416-690399
Fax: 31-416-690340
United Kingdom
505 Eskdale Road
Winnersh Triangle
Wokingham
Berkshire, England RG41 5TU
Tel: 44-118-921-5869
Fax: 44-118-921-5820
05/28/04
DS39636A-page 378
Preliminary
 2004 Microchip Technology Inc.