ALSC AS7C33256NTF36A

AS7C33256NTF32A
AS7C33256NTF36A
November 2004
®
3.3V 256K×32/36 Flowthrough Synchronous SRAM with NTDTM
Features
• Organization: 262,144 words × 32 or 36 bits
• NTD™ architecture for efficient bus operation
• Fast clock to data access: 7.5/8.5/10 ns
• Fast OE access time: 3.5/4.0 ns
• Fully synchronous operation
• Flow-through mode
• Asynchronous output enable control
• Available in 100-pin TQFP
• Byte write enables
• Clock enable for operation hold
• Multiple chip enables for easy expansion
• 3.3 core power supply
• 2.5V or 3.3V I/O operation with separate VDDQ
• 30 mW typical standby power
• Self-timed write cycles
• Interleaved or linear burst modes
• Snooze mode for standby operation
Logic Block Diagram
18
A[17:0]
D
Address
register
Burst logic
Q
18
CLK
D
Q
Write delay
addr. registers
CE0
CE1
CE2
18
CLK
R/W
BWa
Control
logic
DQ[a,b,c,d]
CLK
Write Buffer
BWb
BWc
BWd
ADV / LD
LBO
ZZ
CLK
32/36
D
Data Q
Input
Register
256K x 32/36
SRAM
Array
32/36
32/36
CLK
32/36
32/36
CLK
CEN
Output
Buffer
OE
32/36
OE
DQ[a,b,c,d]
Selection Guide
-75
-85
-10
Units
Minimum cycle time
8.5
10
12
ns
Maximum clock access time
7.5
8.5
10
ns
Maximum operating current
300
280
240
mA
Maximum standby current
120
110
100
mA
Maximum CMOS standby current (DC)
30
30
30
mA
11/8/04, v. 1.1
Alliance Semiconductor
P. 1 of 18
Copyright © Alliance Semiconductor. All rights reserved.
AS7C33256NTF32A
AS7C33256NTF36A
®
8 Mb Synchronous SRAM products list1,2
Org
512KX18
256KX32
Part Number
AS7C33512PFS18A
AS7C33256PFS32A
Mode
PL-SCD
PL-SCD
Speed
166/133 MHz
166/133 MHz
256KX36
512KX18
256KX32
256KX36
512KX18
256KX32
256KX36
512KX18
256KX32
256KX36
AS7C33256PFS36A
AS7C33512PFD18A
AS7C33256PFD32A
AS7C33256PFD36A
AS7C33512FT18A
AS7C33256FT32A
AS7C33256FT36A
AS7C33512NTD18A
AS7C33256NTD32A
AS7C33256NTD36A
PL-SCD
PL-DCD
PL-DCD
PL-DCD
FT
FT
FT
NTD-PL
NTD-PL
166/133 MHz
166/133 MHz
166/133 MHz
166/133 MHz
7.5/8.5/10 ns
7.5/8.5/10 ns
7.5/8.5/10 ns
166/133 MHz
166/133 MHz
512KX18
256KX32
256KX36
AS7C33512NTF18A
AS7C33256NTF32A
AS7C33256NTF36A
NTD-PL
NTD-FT
NTD-FT
NTD-FT
166/133 MHz
7.5/8.5/10 ns
7.5/8.5/10 ns
7.5/8.5/10 ns
1 Core Power Supply: VDD = 3.3V + 0.165V
2 I/O Supply Voltage: VDDQ = 3.3V + 0.165V for 3.3V I/O
VDDQ = 2.5V + 0.125V for 2.5V I/O
PL-SCD
PL-DCD
FT
NTD1-PL
NTD-FT
:
:
:
:
:
Pipelined Burst Synchronous SRAM - Single Cycle Deselect
Pipelined Burst Synchronous SRAM - Double Cycle Deselect
Flow-through Burst Synchronous SRAM
Pipelined Burst Synchronous SRAM with NTDTM
Flow-through Burst Synchronous SRAM with NTDTM
1. NTD: No Turnaround Delay. NTDTM is a trademark of Alliance Semiconductor Corporation. All trademarks mentioned in this document are the property
of their respective owners.
11/8/04, v. 1.1
Alliance Semiconductor
P. 2 of 18
AS7C33256NTF32A
AS7C33256NTF36A
®
DQPc/NC
DQc0
DQc1
VDDQ
VSSQ
DQc2
DQc3
DQc4
DQc5
VSSQ
VDDQ
DQc6
DQc7
NC
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
A
A
A
TQFP 14x20mm
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
DQPb/NC
DQb7
DQb6
VDDQ
VSSQ
DQb5
DQb4
DQb3
DQb2
VSSQ
VDDQ
DQb1
DQb0
Vss
NC
VDD
ZZ
DQa7
DQa6
VDDQ
VSSQ
DQa5
DQa4
DQa3
DQa2
VSSQ
VDDQ
DQa1
DQa0
DQP/NC
LBO
A
A
A
A
A1
A0
NC
NC
VSS
VDD
NC
NC
A
A
A
A
A
A
A
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
VDD
NC
VSS
DQd0
DQd1
VDDQ
VSSQ
DQd2
DQd3
DQd4
DQd5
VSSQ
VDDQ
DQd6
DQd7
DQPd/NC
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
A
A
CE0
CE1
BWd
BWc
BWb
BWa
CE2
VDD
VSS
CLK
R/W
CEN
OE
ADV/LD
NC
Pin arrangement for TQFP (top view)
Note: Pins 1, 30, 51 , and 80 are NC for ×32
11/8/04, v. 1.1
Alliance Semiconductor
P. 3 of 18
AS7C33256NTF32A
AS7C33256NTF36A
®
Functional description
The AS7C33256NTF32A/36A family is a high performance CMOS 8 Mbit Synchronous Static Random Access Memory (Flowthrough
SRAM) organized as 262,144 words × 32 or 36 bits and incorporates a LATE Write.
This variation of the 8Mb sychronous SRAM uses the No Turnaround Delay (NTD™) architecture, featuring an enhanced write operation
that improves bandwidth over pipelined burst devices. In a normal flowthrough burst device, the write data, command, and address are all
applied to the device on the same clock edge. If a read command follows this write command, the system must wait for one 'dead' cycle for
valid data to become available. This dead cycle can significantly reduce overall bandwidth for applications requiring random access or readmodify-write operations.
NTD™ devices use the memory bus more efficiently by introducing a write latency which matches one-cycle flow-through read latency.
Write data is applied one cycle after the write command and address, allowing the read pipeline to clear. With NTD™, write and read
operations can be used in any order without producing dead bus cycle.
Assert R/W low to perform write cycles. Byte write enable controls write access to specific bytes, or can be tied low for full 32/36 bit writes.
Write enable signals, along with the write address, are registered on a rising edge of the clock. Write data is applied to the device one clock
cycle later. Unlike some asynchronous SRAMs, output enable OE does not need to be toggled for write operations; it can be tied low for
normal operations. Outputs go to a high impedance state when the device is de-selected by any of the three chip enable inputs.
Use the ADV (burst advance) input to perform burst read, write and deselect operations. When ADV is high, external addresses, chip select,
R/W pins are ignored, and internal address counters increment in the count sequence specified by the LBO control. Any device operations,
including burst, can be stalled using the CEN=1, the clock enable input.
The AS7C33256NTF32A and AS7C33256NTF36A operate with a 3.3V ± 5% power supply for the device core (VDD). DQ circuits use a
separate power supply (VDDQ) that operates across 3.3V or 2.5V ranges. These devices are available in a 100-pin 14×20 mm TQFP package
Capacitance
Parameter
Input capacitance
I/O capacitance
Symbol
Test conditions
Min
Max
Unit
CIN*
CI/O*
Vin = 0V
-
5
pF
Vin = Vout = 0V
-
7
pF
Units
°C/W
°C/W
°C/W
*Guaranteed not tested
TQFP thermal resistance
Description
Thermal resistance
(junction to ambient)1
Thermal resistance
(junction to top of case)1
Conditions
Test conditions follow standard test methods
and procedures for measuring thermal
impedance, per EIA/JESD51
1–layer
Symbol
θJA
4–layer
θJA
Typical
40
22
θJC
8
1 This parameter is sampled
11/8/04, v. 1.1
Alliance Semiconductor
P. 4 of 18
AS7C33256NTF32A
AS7C33256NTF36A
®
Signal descriptions
Signal
I/O Properties Description
CLK
I
CLOCK
Clock. All inputs except OE, LBO, and ZZ are synchronous to this clock.
CEN
I
SYNC
Clock enable. When de-asserted high, the clock input signal is masked.
A, A0, A1
I
SYNC
Address. Sampled when all chip enables are active and ADV/LD is asserted.
DQ[a,b,c,d]
I/O
SYNC
Data. Driven as output when the chip is enabled and OE is active.
CE0, CE1,
CE2
I
SYNC
Synchronous chip enables. Sampled at the rising edge of CLK, when ADV/LD is asserted.
Are ignored when ADV/LD is high.
ADV/LD
I
SYNC
Advance or Load. When sampled high, the internal burst address counter will increment in
the order defined by the LBO input value. (refer to table on page 2) When low, a new
address is loaded.
R/W
I
SYNC
A high during LOAD initiates a READ operation. A low during LOAD initiates a WRITE
operation. Is ignored when ADV/LD is high.
BW[a,b,c,d]
I
SYNC
Byte write enables. Used to control write on individual bytes. Sampled along with WRITE
command and BURST WRITE.
OE
I
ASYNC
Asynchronous output enable. I/O pins are not driven when OE is inactive.
LBO
I
STATIC
Selects Burst mode. When tied to VDD or left floating, device follows Interleaved Burst
order. When driven Low, device follows linear Burst order. This signal is internally pulled
High.
ZZ
I
ASYNC
Snooze. Places device in low power mode; data is retained. Connect to GND if unused.
NC
-
-
No connects. Note that pin 84 will be used for future address expansion to 16Mb density.
Snooze Mode
SNOOZE MODE is a low current, power-down mode in which the device is deselected and current is reduced to ISB2. The duration of
SNOOZE MODE is dictated by the length of time the ZZ is in a High state.
The ZZ pin is an asynchronous, active high input that causes the device to enter SNOOZE MODE.
When the ZZ pin becomes a logic High, ISB2 is guaranteed after the time tZZI is met. After entering SNOOZE MODE, all inputs except ZZ
become disabled and all outputs go to High-Z. Any operation pending when entering SNOOZE MODE is not guaranteed to successful
complete. Therefore, SNOOZE MODE (READ or WRITE) must not be initiated until valid pending operations are completed. similarly,
when exiting SNOOZE MODE during tPUS, only a DESELECT or READ cycle should be given while the SRAM is transitioning out of
SNOOZE MODE.
Burst Order
Interleaved Burst Order LBO=1
Linear Burst Order LBO=0
A1 A0 A1 A0 A1 A0 A1 A0
A1 A0 A1 A0 A1 A0 A1 A0
Starting Address
00
01
10
11
Starting Address
00
01
10
11
First increment
01
00
11
10
First increment
01
10
11
00
Second increment
10
11
00
01
Second increment
10
11
00
01
Third increment
11
10
01
00
Third increment
11
00
01
10
11/8/04, v. 1.1
Alliance Semiconductor
P. 5 of 18
AS7C33256NTF32A
AS7C33256NTF36A
®
Synchronous truth table[5,6,7,8,9,11]
CE0
CE1 CE2 ADV/LD R/W
BWn
OE
CEN
Address
source
CLK
Operation
DQ
H
X
X
L
X
X
X
L
NA
L to H
DESELECT Cycle
High-Z
X
X
H
L
X
X
X
L
NA
L to H
DESELECT Cycle
High-Z
X
L
X
L
X
X
X
L
NA
L to H
DESELECT Cycle
High-Z
X
X
X
H
X
X
X
L
NA
L to H
CONTINUE DESELECT Cycle
High-Z
L
H
L
L
H
X
L
L
READ Cycle (Begin Burst)
Q
X
X
X
H
X
X
L
L
READ Cycle (Continue Burst)
Q
L
H
L
L
H
X
H
L
X
X
X
H
X
X
H
L
L
H
L
L
L
L
X
L
X
X
X
H
X
L
X
L
L
H
L
L
L
H
X
L
X
X
X
H
X
H
X
L
X
X
X
X
X
X
X
H
External L to H
Next
L to H
External L to H NOP/DUMMY READ (Begin Burst) High-Z
Next
L to H
External L to H
Next
L to H
DUMMY READ (Continue Burst)
L to H
1,10
2
High-Z 1,2,10
D
3
WRITE CYCLE (Continue Burst)
D
1,3,10
High-Z
2,3
WRITE ABORT (Continue Burst)
High-Z
1,2,3,
10
INHIBIT CLOCK
-
4
Current L to H
Key: X = Don’t Care, H = HIGH, L = LOW. BWn = H means all byte write signals (BWa, BWb, BWc, and BWd) are HIGH. BWn = L means one or
more byte write signals are LOW.
Notes:
1 CONTINUE BURST cycles, whether READ or WRITE, use the same control inputs. The type of cycle performed (READ or WRITE) is chose in the initial
BEGIN BURST cycle. A CONINUE DESELECT cycle can only be entered if a DESELECT CYCLE is executed first.
2 DUMMY READ and WRITE ABORT cycles can be considered NOPs because the device performs no external operation. A WRITE ABORT means a
WRITE command is given, but no operation is performed.
3 OE may be wired LOW to minimize the number of control signal to the SRAM. The device will automatically turn off the output drivers during a WRITE
cycle. OE may be used when the bus turn-on and turn-off times do not meet an application’s requirements.
4 If an INHIBIT CLOCK command occurs during a READ operation, the DQ bus will remain active (Low-Z). If it occurs during a WRITE cycle, the bus
will remain in High-Z. No WRITE operations will be performed during the INHIBIT CLOCK cycle.
5 BWa enables WRITEs to byte “a” (DQa pins/balls); BWb enables WRITEs to byte “b” (DQb pins/balls); BWc enables WRITEs to byte “c” (DQc pins/
balls); BWd enables WRITEs to byte “d” (DQd pins/balls).
6 All inputs except OE and ZZ must meet setup and hold times around the rising edge (LOW to HIGH) of CLK.
7 Wait states are inserted by setting CEN HIGH.
8 This device contains circuitry that will ensure that the outputs will be in High-Z during power-up.
9 The device incorporates a 2-bit burst counter. Address wraps to the initial address every fourth BURST CYCLE.
10 The address counter is incremented for all CONTINUE BURST cycles.
11 ZZ pin is always Low.
11/8/04, v. 1.1
1
WRITE CYCLE (Begin Burst)
External L to H NOP/WRITE ABORT (Begin Burst)
Next
Notes
Alliance Semiconductor
P. 6 of 18
AS7C33256NTF32A
AS7C33256NTF36A
®
State Diagram for NTD SRAM
Burst
Read
Read
Read
W
r it
e
Dsel
Burst
l
Dse
ite
Wr
Burst
Write
Dsel
Write
Dsel
ad
Re
Write
Read
Write
Burst
Dsel
Dse
l
Re
ad
Burst
Read
Burst
Write
Burst
Absolute maximum ratings1
Parameter
Symbol
Min
Max
Unit
VDD, VDDQ
–0.5
+4.6
V
Input voltage relative to GND (input pins)
VIN
–0.5
VDD + 0.5
V
Input voltage relative to GND (I/O pins)
VIN
–0.5
VDDQ + 0.5
V
Power dissipation
PD
–
1.8
W
DC output current
IOUT
–
50
mA
Storage temperature (plastic)
Tstg
–65
+150
o
+150
oC
Power supply voltage relative to GND
Temperature under bias (Junction)
Tbias
–65
C
1 Stresses greater than those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional
operation of the device at these or any other conditions outside those indicated in the operational sections of this specification is not implied. Exposure to
absolute maximum rating conditions may affect reliability.
Recommended operating conditions at 3.3V I/O
Parameter
Supply voltage for inputs
Supply voltage for I/O
Ground supply
Symbol
VDD
VDDQ
Vss
Min
3.135
3.135
0
Nominal
3.3
3.3
0
Max
3.465
3.465
0
Unit
V
V
V
Min
3.135
2.375
0
Nominal
3.3
2.5
0
Max
3.465
2.625
0
Unit
V
V
V
Recommended operating conditions at 2.5V I/O
Parameter
Supply voltage for inputs
Supply voltage for I/O
Ground supply
11/8/04, v. 1.1
Symbol
VDD
VDDQ
Vss
Alliance Semiconductor
P. 7 of 18
AS7C33256NTF32A
AS7C33256NTF36A
®
DC electrical characteristics for 3.3V I/O operation
Parameter
Input leakage current1
Output leakage current
Sym
|ILI|
|ILO|
Input high (logic 1) voltage
VIH
Input low (logic 0) voltage
VIL
Output high voltage
Output low voltage
VOH
VOL
Conditions
VDD = Max, 0V < VIN < VDD
OE ≥ VIH, VDD = Max, 0V < VOUT < VDDQ
Address and control pins
I/O pins
Address and control pins
I/O pins
IOH = –4 mA, VDDQ = 3.135V
IOL = 8 mA, VDDQ = 3.465V
Min
-2
-2
2*
2*
-0.3**
-0.5**
2.4
–
Max
2
2
VDD+0.3
VDDQ+0.3
0.8
0.8
–
0.4
Unit
µA
µA
V
V
V
V
1 LBO, and ZZ pins have an internal pull-up or pull-down, and input leakage = ±10 µA.
DC electrical characteristics for 2.5V I/O operation
Parameter
Input leakage current
Output leakage current
Sym
|ILI|
|ILO|
Input high (logic 1) voltage
VIH
Input low (logic 0) voltage
VIL
Output high voltage
Output low voltage
VOH
VOL
Conditions
VDD = Max, 0V < VIN < VDD
OE ≥ VIH, VDD = Max, 0V < VOUT < VDDQ
Address and control pins
I/O pins
Address and control pins
I/O pins
IOH = –4 mA, VDDQ = 2.375V
IOL = 8 mA, VDDQ = 2.625V
*V max < VDD +1.5V for pulse width less than 0.2
IH
**
VIL min = -1.5 for pulse width less than 0.2 X tCYC
Min
-2
-2
1.7*
1.7*
-0.3**
-0.3**
1.7
–
Max
2
2
VDD+0.3
VDDQ+0.3
0.7
0.7
–
0.7
Unit
µA
µA
V
V
V
V
V
V
-75
-85
-10
Unit
300
280
240
mA
120
110
100
30
30
30
30
30
30
X tCYC
IDD operating conditions and maximum limits
Parameter
Sym
Operating power supply current1
ICC
ISB
Standby power supply current
ISB1
ISB2
Conditions
CE0 < VIL, CE1 > VIH, CE2 < VIL, f = fMax,
IOUT = 0 mA, ZZ < VIL
All VIN ≤ 0.2V or > VDD – 0.2V, Deselected,
f = fMax, ZZ < VIL
Deselected, f = 0, ZZ < 0.2V,
all VIN ≤ 0.2V or ≥ VDD – 0.2V
Deselected, f = fMax, ZZ ≥ VDD – 0.2V,
all VIN ≤ VIL or ≥ VIH
mA
1 ICC given with no output loading. ICC increases with faster cycle times and greater output loading.
11/8/04, v. 1.1
Alliance Semiconductor
P. 8 of 18
AS7C33256NTF32A
AS7C33256NTF36A
®
Timing characteristics over operating range
-75
Parameter
Sym
–85
–10
Min Max Min Max Min Max Unit
Notes1
Cycle time
tCYC
8.5
-
10
–
12
–
ns
Clock access time
tCD
-
7.5
–
8.5
–
10
ns
Output enable low to data valid
tOE
-
3.5
–
4.0
–
4.0
ns
Clock high to output low Z
tLZC
2.5
-
2.5
–
2.5
–
ns
2,3,4
Data Output invalid from clock high
tOH
2.5
-
2.5
–
2.5
–
ns
2
Output enable low to output low Z
tLZOE
0.0
-
0
–
0
–
ns
2,3,4
Output enable high to output high Z
tHZOE
-
3.5
–
4.0
–
4.0
ns
2,3,4
Clock high to output high Z
tHZC
-
4.0
–
5.0
–
5.0
ns
2,3,4
Output enable high to invalid output
tOHOE
0.0
-
0
–
0
–
ns
Clock high pulse width
tCH
2.8
-
3.0
–
3.0
–
ns
5
Clock low pulse width
tCL
2.8
-
3.0
–
3.0
–
ns
5
Address and Control setup to clock high
tAS
2.0
-
2.0
–
2.0
–
ns
6
Data setup to clock high
tDS
2.0
-
2.0
–
2.0
–
ns
6
Write setup to clock high
tWS
2.0
-
2.0
–
2.0
–
ns
6, 7
Chip select setup to clock high
tCSS
2.0
-
2.0
–
2.0
–
ns
6, 8
Address hold from clock high
tAH
0.5
-
0.5
–
0.5
–
ns
6
Data hold from clock high
tDH
0.5
-
0.5
–
0.5
–
ns
6
Write hold from clock high
tWH
0.5
-
0.5
–
0.5
–
ns
6, 7
Chip select hold from clock high
tCSH
0.5
-
0.5
–
0.5
–
ns
6, 8
Clock enable setup to clock high
tCENS
2.0
-
2.0
–
2.0
–
ns
6
Clock enable hold from clock high
tCENH
0.5
-
0.5
–
0.5
–
ns
6
ADV setup to clock high
tADVS
2.0
-
2.0
–
2.0
–
ns
6
ADV hold from clock high
tADVH
0.5
-
0.5
–
0.5
–
ns
6
1 See “AC test conditions” on page 15.
Snooze Mode Electrical Characteristics
Description
Current during Snooze Mode
ZZ active to input ignored
ZZ inactive to input sampled
ZZ active to SNOOZE current
ZZ inactive to exit SNOOZE current
11/8/04, v. 1.1
Conditions
Symbol
ZZ > VIH
ISB2
tPDS
tPUS
tZZI
tRZZI
Alliance Semiconductor
Min
Max
Units
30
mA
cycle
cycle
cycle
2
2
2
0
P. 9 of 18
AS7C33256NTF32A
AS7C33256NTF36A
®
Key to switching waveforms
Rising input
don’t care
Falling input
Undefined
Timing waveform of read cycle
tCH
tCL
tCYC
CLK
tCENS tCENH
CEN
tAS
Address
tAH
A1
A2
A3
tWS tWH
R/W
tCSS
tCSH
CE0,CE2
CE1
tADVS tADVH
ADV/LD
OE
tHZOE
tOE
Dout
tLZOE
Q(A1)
Q(A2Y‘11)
Q(A2)
Q(A3)
Q(A3Y‘01)
Q(A2Y‘01) Q(A2Y‘10)
Command
11/8/04, v. 1.1
READ
Q(A1)
DSEL
READ
Q(A2)
BURST
BURST
READ
READ
READ
Q(A2Ý11)
Q(A2Ý01) Q(A2Ý10)
BURST
Alliance Semiconductor
STALL
READ
Q(A3)
BURST
READ
Q(A3Ý01)
P. 10 of 18
AS7C33256NTF32A
AS7C33256NTF36A
®
Timing waveform of write cycle
tCH
tCL
tCYC
CLK
tCENS tCENH
CEN
tAS
tAH
A1
Address
A2
A3
R/W
BWn
tCSS
tCSH
CE0,CE2
CE1
tADVS tADVH
ADV/LD
OE
tDS
D(A1)
Din
Command
11/8/04, v. 1.1
D(A3)
D(A2)
tHZOE
Dout
tDH
D(A2Y‘01) D(A2Y‘10)
D(A2Y‘11)
D(A3Y‘01)
Q(n-1)
WRITE
D(A1)
DSEL
WRITE
D(A2)
BURST
BURST
BURST
WRITE
WRITE
WRITE
D(A2Ý01) D(A2Ý10) D(A2Ý11)
Alliance Semiconductor
STALL
WRITE
D(A3)
BURST
WRITE
D(A3Ý01)
P. 11 of 18
AS7C33256NTF32A
AS7C33256NTF36A
®
Timing waveform of read/write cycle
tCH
tCL
tCYC
CLK
tCENS
tCENH
CEN
tAS
tAH
A1
ADDRESS
A3
A2
tWS
tWH
tWS
tWH
tCSS
tCSH
tADVS
tADVH
A4
A5
A6
A7
D(A5)
Q(A6)
R/W
BWn
CE0, CE2
CE1
ADV/LD
OE
tCD
tDS tDH
D/Q
D(A1)
tLZC
D(A2)
D(A2Ý01)
tHZOE
tOE
tOH
Q(A3)
Q(A4)
tHZC
Q(A4Ý01)
D(A7)
tLZOE
Command
WRITE
D(A1)
WRITE
D(A2)
BURST
WRITE
D(A2Ý01)
READ
Q(A3)
READ
Q(A4)
BURST
READ
Q(A4Ý01)
WRITE
D(A5)
READ
Q(A6)
WRITE
D(A7)
DSEL
Note: Ý = XOR when LBO = high/no connect. Ý = ADD when LBO = low.
11/8/04, v. 1.1
Alliance Semiconductor
P. 12 of 18
AS7C33256NTF32A
AS7C33256NTF36A
®
NOP, stall and deselect cycles
CLK
CEN
CE1
CE0, CE2
ADV/LD
R/W
BWn
Address
A2
A1
D/Q
Command
Q(A1)
READ
Q(A1)
Q(A1Ý01)
BURST STALL
Q(A1Ý01)
A3
D(A2)
Q(A1Ý10)
BURST DSEL
Q(A1Ý10)
BURST
DSEL
WRITE
D(A2)
BURST BURST WRITE
NOP
D(A2Ý10) NOP
D(A2Ý01)
D(A3)
Note: Ý = XOR when LBO = high/no connect; Ý = ADD when LBO = low. OE is low.
11/8/04, v. 1.1
Alliance Semiconductor
P. 13 of 18
AS7C33256NTF32A
AS7C33256NTF36A
®
Timing waveform of snooze mode
CLK
tPUS
ZZ setup cycle
ZZ recovery cycle
ZZ
tZZI
Isupply
ISB2
tRZZI
All inputs
(except ZZ)
Deselect or Read Only
Deselect or Read Only
Normal
operation
Cycle
Dout
11/8/04, v. 1.1
High-Z
Alliance Semiconductor
P. 14 of 18
AS7C33256NTF32A
AS7C33256NTF36A
®
AC test conditions
• Output Load: see Figure B,
except for tLZC, tLZOE, tHZOE, tHZC see Figure C.
• Input pulse level: GND to 3V. See Figure A.
• Input rise and fall time (Measured at 0.3V and 2.7V): 2 ns. See Figure A.
• Input and output timing reference levels: 1.5V.
+3.0V
90%
10%
GND
90%
10%
Figure A: Input waveform
Dout
Z0=50Ω
50Ω
Thevenin equivalent:
+3.3V for 3.3V I/O;
/+2.5V for 2.5V I/O
DOUT
VL=1.5V
353Ω/1538Ω
30 pF*
Figure B: Output load (A)
319Ω/1667Ω
5 pF*
GND *including scope
and jig capacitance
Figure C: Output load(B)
Notes
1
2
3
4
5
6
7
8
9
For test conditions, see AC Test Conditions, Figures A, B, C.
This parameter measured with output load condition in Figure C
This parameter is sampled and not 100% tested.
tHZOE is less than tLZOE; and tHZC is less than tLZC at any given temperature and voltage.
tHZCN is a‘no load’ parameter to indicate exactly when SRAM outputs have stopped driving.
ICC given with no output loading. ICC increases with faster cycle times and greater output loading.
Transitions are measured ±500 mV from steady state voltage. Output loading specified with CL = 5 pF as in Figure C.
tCH measured as high above VIH, and tCL measured as low below VIL
This is a synchronous device. All addresses must meet the specified setup and hold times for all rising edges of CLK. All other synchronous inputs mus
meet the setup and hold times with stable logic levels for all rising edges of CLK when chip is enabled.
11/8/04, v. 1.1
Alliance Semiconductor
P. 15 of 18
AS7C33256NTF32A
AS7C33256NTF36A
®
Package Dimensions
100-pin quad flat pack (TQFP)
Hd
D
b
TQFP
Min
Max
A1
0.05
0.15
A2
1.35
1.45
b
0.22
0.38
c
0.09
0.20
D
13.80
14.20
E
19.80
20.20
e
e
α
0.65 nominal
A2
c
Hd
15.80
16.20
He
21.80
22.20
L1
L
0.45
0.75
L
L1
α
He E
A1
1.00 nominal
0°
7°
Dimensions in millimeters
11/8/04, v. 1.1
Alliance Semiconductor
P. 16 of 18
AS7C33256NTF32A
AS7C33256NTF36A
®
Ordering information
Package
TQFP
TQFP
TQFP
TQFP
Width
x32
x32
x36
x36
-75
AS7C33256NTF32A-75TQC
AS7C33256NTF32A-75TQI
AS7C33256NTF36A-75TQC
AS7C33256NTF36A-75TQI
-85
AS7C33256NTF32A-85TQC
AS7C33256NTF32A-85TQI
AS7C33256NTF36A-85TQC
AS7C33256NTF36A-85TQI
-10
AS7C33256NTF32A-10TQC
AS7C33256NTF32A-10TQI
AS7C33256NTF36A-10TQC
AS7C33256NTF36A-10TQI
Note: Add suffix ‘N’ to he above part numbers for Lead Free Parts (Ex. AS7C33256NTF32A-85TQCN)
Part numbering guide
AS7C
33
256
NTF
32/36
A
–XX
TQ
C/I
X
1
2
3
4
5
6
7
8
9
10
1.Alliance Semiconductor SRAM prefix
2.Operating voltage: 33 = 3.3V
3.Organization: 256 = 256K
4.NTF = No Turn-around Delay, Flowthrough mode
5.Organization: 32 = x32; 36 = x36
6.Production version: A = first production version
7.Clock access time [-75 = 7.5 ns; -85 = 8.5 ns; -10 = 10 ns]
8.Package type: TQ = TQFP.
9.Operating temperature: C = commercial (0° C to 70° C); I = industrial (-40° C to 85° C)
10. N = Lead free part
11/8/04, v. 1.1
Alliance Semiconductor
P. 17 of 18
AS7C33256NTF32A
AS7C33256NTF36A
®
Alliance Semiconductor
Corporation
®
Copyright © Alliance Semiconductor
2575, Augustine Drive,
All Rights Reserved
Santa Clara, CA 95054
Part Number:AS7C33256NTF32A
AS7C33256NTF36A
Tel: 408 - 855 - 4900
Fax: 408 - 855 - 4999
Document Version: v. 1.1
www.alsc.com
© Copyright 2003 Alliance Semiconductor Corporation. All rights reserved. Our three-point logo, our name and
Intelliwatt are trademarks or registered trademarks of Alliance. All other brand and product names may be the
trademarks of their respective companies. Alliance reserves the right to make changes to this document and its products
at any time without notice. Alliance assumes no responsibility for any errors that may appear in this document. The data
contained herein represents Alliance's best data and/or estimates at the time of issuance. Alliance reserves the right to
change or correct this data at any time, without notice. If the product described herein is under development, significant
changes to these specifications are possible. The information in this product data sheet is intended to be general
descriptive information for potential customers and users, and is not intended to operate as, or provide, any guarantee or
warrantee to any user or customer. Alliance does not assume any responsibility or liability arising out of the application
or use of any product described herein, and disclaims any express or implied warranties related to the sale and/or use of
Alliance products including liability or warranties related to fitness for a particular purpose, merchantability, or
infringement of any intellectual property rights, except as express agreed to in Alliance's Terms and Conditions of Sale
(which are available from Alliance). All sales of Alliance products are made exclusively according to Alliance's Terms
and Conditions of Sale. The purchase of products from Alliance does not convey a license under any patent rights,
copyrights; mask works rights, trademarks, or any other intellectual property rights of Alliance or third parties. Alliance
does not authorize its products for use as critical components in life-supporting systems where a malfunction or failure
may reasonably be expected to result in significant injury to the user, and the inclusion of Alliance products in such lifesupporting systems implies that the manufacturer assumes all risk of such use and agrees to indemnify Alliance against
all claims arising from such use.