TI TRS3318IDBR

www.ti.com
FEATURES
TRS3318
2.5-V 460-kbps RS-232 TRANSCEIVER
WITH ±15-kV ESD PROTECTION
SLLS820 – AUGUST 2007
1
•
•
•
•
•
•
ESD Protection for RS-232 I/O Pins
– ±15 kV Human-Body Model (HBM)
– ±8 kV IEC 61000-4-2, Contact Discharge
– ±8 kV IEC 61000-4-2, Air-Gap Discharge
300-μA Operating Supply Current
1-μA Low-Power Standby (With Receivers
Active) Mode
Designed to Transmit at a Data Rate of
460 kbps
Auto-Powerdown Plus Option Features
Flexible Power-Saving Mode
Operates From a Single 2.25-V to 3-V VCC
Supply
DB OR PW PACKAGE
(TOP VIEW)
READY
C1+
V+
C1−
C2+
C2−
V−
DOUT2
RIN2
ROUT2
1
20
2
19
3
18
4
17
5
16
6
15
7
14
8
13
9
12
10
11
FORCEOFF
VCC
GND
DOUT1
RIN1
ROUT1
FORCEON
DIN1
DIN2
INVALID
APPLICATIONS
•
•
•
•
•
•
Battery-Powered Systems
PDAs
Cellular Phones
Notebooks
Hand-Held Equipment
Pagers
DESCRIPTION/ORDERING INFORMATION
The TRS3318 is a dual-driver, dual-receiver, RS-232 compatible transceiver. The device features
auto-powerdown plus and enhanced electrostatic discharge (ESD) protection integrated into the chip. Driver
output and receiver input are protected to ±8 kV using the IEC 61000-4-2 Air-Gap Discharge method, ±8 kV
using the IEC 61000-4-2 Contact Discharge method, and ±15 kV using the Human-Body Model (HBM).
The device operates at a data rate of 460 kbps. The transceiver has a proprietary low-dropout driver output stage
enabling RS-232-compatible operation from a 2.25-V to 3-V supply with a dual charge pump. The charge pump
requires only four 0.1-μF capacitors and features a logic-level output (READY) that asserts when the charge
pump is regulating and the device is ready to begin transmitting.
The TRS3318 achieves a 1-μA supply current using the auto-powerdown feature. This device automatically
enters a low-power power-down mode when the RS-232 cable is disconnected or the drivers of the connected
peripherals are inactive for more than 30 s. The device turns on again when it senses a valid transition at any
driver or receiver input. Auto-powerdown saves power without changes to the existing BIOS or operating system.
This device is available in two space-saving packages: 20-pin SSOP and 20-pin TSSOP.
Flexible control options for power management are featured when the serial port and driver inputs are inactive.
The auto-powerdown plus feature functions when FORCEON is low and FORCEOFF is high. During this mode of
operation, if the device does not sense valid signal transitions on all receiver and driver inputs for approximately
30 s, the built-in charge pump and drivers are powered down, reducing the supply current to 1 μA. By
disconnecting the serial port or placing the peripheral drivers off, auto-powerdown plus can be disabled when
FORCEON and FORCEOFF are high. With auto-powerdown plus enabled, the device activates automatically
when a valid signal is applied to any receiver or driver input. INVALID is high (valid data) if any receiver input
voltage is greater than 2.7 V or less than –2.7 V, or has been between –0.3 V and 0.3 V for less than 30 μs
(typical number). INVALID is low (invalid data) if all receiver input voltage are between –0.3 V and 0.3 V for more
than 30 μs (typical number).
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2007, Texas Instruments Incorporated
TRS3318
2.5-V 460-kbps RS-232 TRANSCEIVER
WITH ±15-kV ESD PROTECTION
www.ti.com
SLLS820 – AUGUST 2007
ORDERING INFORMATION
TA
PACKAGE
SSOP – DB
0°C to 70°C
TSSOP – PW
SSOP – DB
–40°C to 85°C
TSSOP – PW
(1)
(2)
(1) (2)
ORDERABLE PART NUMBER
Tube of 70
TRS3318CDB
Reel of 2000
TRS3318CDBR
Tube of 70
TRS3318CPW
Reel of 2000
TRS3318CPWR
Tube of 70
TRS3318IDB
Reel of 2000
TRS3318IDBR
Tube of 70
TRS3318IPW
Reel of 2000
TRS3318IPWR
TOP-SIDE MARKING
RV18C
RV18C
RV18I
RV18I
Package drawings,thermal data, and symbolization are available at www.ti.com/packaging.
For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
website at www.ti.com.
FUNCTION TABLE (1)
INPUT CONDITIONS
FORCEON
FORCEOFF
RECEIVER
OR DRIVER
EDGE
WITHIN 30 s
OUTPUT STATES
VALID
RS-232
LEVEL
PRESENT AT
RECEIVER
DRIVER
RECEIVER
INVALID
READY
OPERATING
MODE
Auto-Powerdown Plus Conditions
H
H
No
No
Active
Active
L
H
Normal operation,
auto-powerdown
plus disabled
H
H
No
Yes
Active
Active
H
H
Normal operation,
auto-powerdown
plus disabled
L
H
Yes
No
Active
Active
L
H
Normal operation,
auto-powerdown
plus enabled
L
H
Yes
Yes
Active
Active
H
H
Normal operation,
auto-powerdown
plus enabled
L
H
No
No
Z
Active
L
L
Power down,
auto-powerdown
plus enabled
L
H
No
Yes
Z
Active
H
L
Power down,
auto-powerdown
plus enabled
X
L
X
No
Z
Active
L
L
Manual power
down
X
L
X
Yes
Z
Active
H
L
Manual power
down
Auto-Powerdown Conditions
(1)
2
INVALID
INVALID
X
No
Z
Active
L
L
Power down,
auto-powerdown
enabled
INVALID
INVALID
X
Yes
Active
Active
H
H
Normal operation,
auto-powerdown
enabled
H = high level, L = low level, X = irrelevant, Z = high impedance
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): TRS3318
TRS3318
2.5-V 460-kbps RS-232 TRANSCEIVER
WITH ±15-kV ESD PROTECTION
www.ti.com
SLLS820 – AUGUST 2007
LOGIC DIAGRAM (POSITIVE LOGIC)
DIN1
DIN2
FORCEOFF
FORCEON
ROUT1
13
17
12
8
20
11
14
Auto-Powerdown Plus
15
DOUT1
DOUT2
INVALID
1
READY
16
RIN1
5 kΩ
ROUT2
10
9
RIN2
5 kΩ
TERMINAL FUNCTIONS
TERMINAL
NAME
DESCRIPTION
NO.
C1+
2
Positive voltage-doubler charge-pump capacitor
C1–
4
Negative voltage-doubler charge-pump capacitor
C2+
5
Positive inverting charge-pump capacitor
C2–
6
Negative inverting charge-pump capacitor
DIN
12, 13
CMOS driver inputs
DOUT
8, 17
RS-232 driver outputs
FORCEOFF
20
Force-off input, active low. Drive low to power down transmitters, receivers, and charge pump. This overrides
auto-powerdown and FORCEON (see Function Table).
FORCEON
14
Force-on input, active high. Drive high to override auto-powerdown, keeping transmitters and receivers on
(FORCEOFF must be high) (see Function Table).
GND
18
Ground
INVALID
11
Valid signal detector output, active low. A logic high indicates that a valid RS-232 level is present on a receiver
input.
READY
1
Ready to transmit output, active high. READY is enabled high when V– goes below –3.5 V and the device is
ready to transmit.
RIN
9, 16
RS-232 receiver inputs
ROUT
10, 15
CMOS receiver outputs
V+
3
2 × VCC generated by the charge pump
V–
7
–2 × VCC generated by the charge pump
VCC
19
2.25-V to 3-V single-supply voltage
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): TRS3318
3
TRS3318
2.5-V 460-kbps RS-232 TRANSCEIVER
WITH ±15-kV ESD PROTECTION
www.ti.com
SLLS820 – AUGUST 2007
Absolute Maximum Ratings (1)
over operating free-air temperature range (unless otherwise noted)
MIN
MAX
VCC
Supply voltage range
–0.3
6
V
V+
Positive supply voltage range (2)
–0.3
7
V
–7
0.3
V
13
V
V–
Negative supply voltage range
V+ + IV–I
Supply voltage differential (2)
VI
Input voltage
VO
Output voltage
(2)
DIN, FORCEON, FORCEOFF to GND
6
RIN to GND
±13.2
ROUT, INVALID, READY to GND
–0.3
DOUT to GND
Continuous power dissipation
(TA = 70°C)
(2)
V
VCC + 0.3
Continuous
16-pin SSOP (derate 7.14 mW/°C above 70°C)
571
20-pin SSOP (derate 8 mW/°C above 70°C
640
20-pin TSSOP (derate 7 mW/°C above 70°C)
559
Storage temperature range
–65
Lead temperature (soldering, 10 s)
(1)
V
±25
DOUT to GND
Short-circuit duration
Tstg
–0.3
UNIT
mW
150
°C
300
°C
Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating
conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
V+ and V– can have maximum magnitudes of 7 V, but their absolute difference cannot exceed 13 V.
Recommended Operating Conditions
See Figure 4
MIN NOM
Supply voltage
2.25
MAX UNIT
2.5
3
V
VIH
Driver and control high-level input voltage
DIN, FORCEOFF,
FORCEON
VCC = 2.5 V to 3 V
0.7 × VCC
5.5
V
VIL
Driver and control low-level input voltage
DIN, FORCEOFF,
FORCEON
VCC = 2.5 V to 3 V
0
0.3 × VCC
V
VI
Receiver input voltage
–25
25
V
0
70
–40
85
TA
TRS3318C
Operating free-air temperature
TRS3318I
°C
Electrical Characteristics
VCC = 2.25 V to 3 V, C1–C4 = 0.1 μF, TA = TMIN to TMAX (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP (1) MAX
UNIT
DC Characteristics (VCC = 2.5 V, TA = 25°C)
μA
Auto-powerdown plus supply current
FORCEON = GND, FORCEOFF = VCC, All RIN and DIN idle
1
10
Auto-powerdown supply current
FORCEOFF = GND
1
10
μA
Supply current
FORCEON = FORCEOFF = VCC, No load
0.3
2
mA
(1)
Typical values are at VCC = 2.5 V, TA = 25°C.
ESD Protection
PARAMETER
TEST CONDITIONS
Human-Body Model (HBM)
RIN, DOUT
4
TYP
IEC 61000-4-2 Air-Gap Discharge method
±8
IEC 61000-4-2 Contact Discharge method
±8
Submit Documentation Feedback
UNIT
±15
kV
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): TRS3318
TRS3318
2.5-V 460-kbps RS-232 TRANSCEIVER
WITH ±15-kV ESD PROTECTION
www.ti.com
SLLS820 – AUGUST 2007
DRIVER SECTION
Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature,
VCC = 2.25 V to 3 V, C1–C4 = 0.1 μF, TA = TMIN to TMAX (unless otherwise noted) (see Figure 4)
PARAMETER
TEST CONDITIONS
MIN
TYP (1)
Vhys
Driver input hysteresis
Ion
Input leakage current
FORCEON, DIN, FORCEOFF
Vom
Output voltage swing
All driver outputs loaded with 3 kΩ to ground
±3.7
±4
rO
Output resistance
VCC = 0, Driver output = ±2 V
300
10M
IOS
Output short-circuit current (2)
Ioff
Output leakage current
(1)
(2)
MAX
0.3
±0.01
±25
VCC = 0 or 2.25 V to 3 V, VOUT = ±12 V, Drivers
disabled
UNIT
V
±1
μA
V
Ω
±60
mA
±25
μA
Typical values are at VCC = 2.5 V, TA = 25°C.
Short-circuit durations should be controlled to prevent exceeding the device absolute power dissipation ratings, and not more than one
output should be shorted at a time.
Switching Characteristics
over recommended ranges of supply voltage and operating free-air temperature,
VCC = 2.25 V to 3 V, C1–C4 = 0.1 μF, TA = TMIN to TMAX (unless otherwise noted) (see Figure 1)
PARAMETER
Maximum data rate
TEST CONDITIONS
MIN
RL = 3 kΩ, CL = 1000 pF, One transmitter switching
(1)
(2)
Transition-region slew rate
MAX
460
|tPHL – tPLH| Driver skew (2)
SR(tr)
TYP (1)
kbps
100
VCC = 2.5 V, TA = 25°C, RL = 3 kΩ to 7 kΩ,
Measured from 3 V to –3 V or –3 V to 3 V,
CL = 150 pF to 2500 pF
4
UNIT
ns
30
V/μs
Typical values are at VCC = 2.5 V, TA = 25°C.
Pulse skew is defined as |tPLH – tPHL| of each channel of the same device.
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): TRS3318
5
TRS3318
2.5-V 460-kbps RS-232 TRANSCEIVER
WITH ±15-kV ESD PROTECTION
www.ti.com
SLLS820 – AUGUST 2007
RECEIVER SECTION
Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature,
VCC = 2.25 V to 3 V, C1–C4 = 0.1 μF, TA = TMIN to TMAX (unless otherwise noted) (see Figure 4)
PARAMETER
TEST CONDITIONS
MIN
VI
Input voltage range
VIT+
Input voltage threshold low
TA = 25°C
VIT–
Input voltage threshold high
TA = 25°C
0.7 × VCC
Vhys
Input hysteresis
ri
Input resistance
TA = 25°C
3
Ioff
Output leakage current
VOL
Output voltage low
IOUT = 0.5 mA
VOH
Output voltage high
IOUT = –0.5 mA
(1)
TYP (1)
–25
MAX UNIT
25
V
0.3 × VCC
V
V
0.3
V
5
±0.05
7
kΩ
±10
μA
0.1 × VCC
V
0.9 × VCC
V
Typical values are at VCC = 2.5 V, TA = 25°C.
Switching Characteristics
over recommended ranges of supply voltage and operating free-air temperature,
VCC = 2.25 V to 3 V, C1–C4 = 0.1 μF, TA = TMIN to TMAX (unless otherwise noted) (see Figure 4)
PARAMETER
tPHL
Receiver propagation delay
tPLH
|tPHL – tPLH|
(1)
(2)
6
TEST CONDITIONS
RIN to ROUT, CL = 150 pF
Receiver skew (2)
TYP (1)
0.175
0.175
50
UNIT
μs
ns
Typical values are at VCC = 2.5 V, TA = 25°C.
Pulse skew is defined as |tPLH – tPHL| of each channel of the same device.
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): TRS3318
TRS3318
2.5-V 460-kbps RS-232 TRANSCEIVER
WITH ±15-kV ESD PROTECTION
www.ti.com
SLLS820 – AUGUST 2007
AUTO-POWERDOWN PLUS SECTION
Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature,
VCC = 2.25 V to 3 V, C1–C4 = 0.1 μF, TA = TMIN to TMAX (unless otherwise noted) (see Figure 4)
PARAMETER
TEST CONDITIONS
MIN
MAX
Positive threshold
Receiver input threshold to INVALID high
2.7
Negative threshold
–2.7
Receiver input threshold INVALID low
–0.3
INVALID, READY voltage low
IOUT = 0.5 mA
INVALID, READY voltage high
IOUT = –0.5 mA
UNIT
V
0.3
V
0.1 × VCC
V
0.8 × VCC
V
Switching Characteristics
over recommended ranges of supply voltage and operating free-air temperature,
VCC = 2.25 V to 3 V, C1–C4 = 0.1 μF, TA = TMIN to TMAX (unless otherwise noted) (see Figure 4)
PARAMETER
TEST CONDITIONS
MIN
TYP (1)
MAX
UNIT
tINVH
Receiver positive or negative threshold to INVALID high
VCC = 2.5 V
1
μs
tINVL
Receiver positive or negative threshold to INVALID low
VCC = 2.5 V
30
μs
tWU
Receiver or driver edge to driver enabled
VCC = 2.5 V
100
μs
tAUTOPRDN
Receiver or driver edge to driver shutdown
VCC = 2.5 V
(1)
15
30
60
s
Typical values are at VCC = 2.5 V,TA = 25°C.
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): TRS3318
7
TRS3318
2.5-V 460-kbps RS-232 TRANSCEIVER
WITH ±15-kV ESD PROTECTION
www.ti.com
SLLS820 – AUGUST 2007
PARAMETER MEASUREMENT INFORMATION
3V
Generator
(see Note B)
Input
RS-232
Output
50 Ω
RL
CL
(see Note A)
3V
FORCEOFF
TEST CIRCUIT
0V
tTHL
Output
6V
SR(tr) +
t THL or tTLH
tTLH
VOH
3V
3V
−3 V
−3 V
VOL
VOLTAGE WAVEFORMS
NOTES: A. CL includes probe and jig capacitance.
B. The pulse generator has the following characteristics: PRR = 250 kbit/s, ZO = 50 Ω, 50% duty cycle, tr ≤ 10 ns, tf ≤ 10 ns.
Figure 1. Driver Slew Rate
2.25 V
Generator
(see Note B)
RS-232
Output
50 Ω
RL
Input
1.125 V
1.125 V
0V
CL
(see Note A)
tPLH
tPHL
VOH
3V
FORCEOFF
50%
50%
Output
VOL
TEST CIRCUIT
VOLTAGE WAVEFORMS
NOTES: A. CL includes probe and jig capacitance.
B. The pulse generator has the following characteristics: PRR = 250 kbit/s, ZO = 50 Ω, 50% duty cycle, tr ≤ 10 ns, tf ≤ 10 ns.
Figure 2. Driver Pulse Skew
3V
Input
0V
0V
−3 V
Output
Generator
(see Note B)
tPHL
50 Ω
tPLH
CL
(see Note A)
VOH
50%
Output
50%
VOL
TEST CIRCUIT
VOLTAGE WAVEFORMS
NOTES: A. CL includes probe and jig capacitance.
B. The pulse generator has the following characteristics: ZO = 50 Ω, 50% duty cycle, tr ≤ 10 ns, tf ≤ 10 ns.
Figure 3. Receiver Propagation Delay Times
8
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): TRS3318
TRS3318
2.5-V 460-kbps RS-232 TRANSCEIVER
WITH ±15-kV ESD PROTECTION
www.ti.com
SLLS820 – AUGUST 2007
PARAMETER MEASUREMENT INFORMATION
Receiver
Inputs
}
Invalid
Region
Driver
Inputs
Driver
Outputs
VCC
INVALID
Output
tINVL
tINVH
0
tWU
tWU
VCC
Ready
Output
0
V+
VCC
0
V−
VOLTAGE WAVEFORMS
ÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎ
Valid RS-232 Level, INVALID High
ROUT
Generator
(see Note B)
2.7 V
50 Ω
Indeterminate
0.3 V
0V
If Signal Remains Within This Region
For More Than 30 µs, INVALID Is Low†
−0.3 V
Auto-Powerdown
Plus
Indeterminate
INVALID
−2.7 V
CL = 30 pF
(see Note A)
†
FORCEON
FORCEOFF
Valid RS-232 Level, INVALID High
DIN
DOUT
Auto power down disables drivers and reduces supply
current to 1 µA.
TEST CIRCUIT
Figure 4. INVALID Propagation Delay Times and Supply Enabling Time
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): TRS3318
9
TRS3318
2.5-V 460-kbps RS-232 TRANSCEIVER
WITH ±15-kV ESD PROTECTION
www.ti.com
SLLS820 – AUGUST 2007
APPLICATION INFORMATION
2.5 V
+ 0.1 mF
19
CBYPASS
2
C1
0.1 mF
C2
0.1 mF
+
4
+
5
6
VCC
C1+
V+
3
+
C1−
V−
C2+
7
C2−
13 DIN1
DOUT1 17
12 DIN2
DOUT2 8
C4
+ 0.1 mF
RS-232-Compatible
Outputs
RS-232-Compatible
Inputs
RIN1 16
15 ROUT1
C3
0.1 mF
5k
10 ROUT2
1
RIN2 9
5k
READY
To Power-Management Unit
Auto-Powerdown INVALID 11
Plus
VCC
FORCEOFF 20
14
FORCEON
GND
18
Figure 5. Typical Application Circuit
10
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): TRS3318
PACKAGE OPTION ADDENDUM
www.ti.com
26-Sep-2007
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
TRS3318CDB
ACTIVE
SSOP
DB
20
70
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TRS3318CDBG4
ACTIVE
SSOP
DB
20
70
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TRS3318CDBR
ACTIVE
SSOP
DB
20
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TRS3318CDBRG4
ACTIVE
SSOP
DB
20
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TRS3318CPW
ACTIVE
TSSOP
PW
20
70
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TRS3318CPWG4
ACTIVE
TSSOP
PW
20
70
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TRS3318CPWR
ACTIVE
TSSOP
PW
20
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TRS3318CPWRG4
ACTIVE
TSSOP
PW
20
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TRS3318IDB
ACTIVE
SSOP
DB
20
70
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TRS3318IDBG4
ACTIVE
SSOP
DB
20
70
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TRS3318IDBR
ACTIVE
SSOP
DB
20
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TRS3318IDBRG4
ACTIVE
SSOP
DB
20
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TRS3318IPW
ACTIVE
TSSOP
PW
20
70
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TRS3318IPWG4
ACTIVE
TSSOP
PW
20
70
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TRS3318IPWR
ACTIVE
TSSOP
PW
20
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TRS3318IPWRG4
ACTIVE
TSSOP
PW
20
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
Lead/Ball Finish
MSL Peak Temp (3)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
26-Sep-2007
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
4-Oct-2007
TAPE AND REEL BOX INFORMATION
Device
Package Pins
Site
Reel
Diameter
(mm)
Reel
Width
(mm)
A0 (mm)
B0 (mm)
K0 (mm)
P1
(mm)
W
Pin1
(mm) Quadrant
TRS3318CDBR
DB
20
SITE 41
330
16
8.2
7.5
2.5
12
16
Q1
TRS3318CPWR
PW
20
SITE 41
330
16
6.95
7.1
1.6
8
16
Q1
TRS3318IDBR
DB
20
SITE 41
330
16
8.2
7.5
2.5
12
16
Q1
TRS3318IPWR
PW
20
SITE 41
330
16
6.95
7.1
1.6
8
16
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
Device
4-Oct-2007
Package
Pins
Site
Length (mm)
Width (mm)
Height (mm)
TRS3318CDBR
DB
20
SITE 41
346.0
346.0
33.0
TRS3318CPWR
PW
20
SITE 41
346.0
346.0
33.0
TRS3318IDBR
DB
20
SITE 41
346.0
346.0
33.0
TRS3318IPWR
PW
20
SITE 41
346.0
346.0
33.0
Pack Materials-Page 2
MECHANICAL DATA
MSSO002E – JANUARY 1995 – REVISED DECEMBER 2001
DB (R-PDSO-G**)
PLASTIC SMALL-OUTLINE
28 PINS SHOWN
0,38
0,22
0,65
28
0,15 M
15
0,25
0,09
8,20
7,40
5,60
5,00
Gage Plane
1
14
0,25
A
0°–ā8°
0,95
0,55
Seating Plane
2,00 MAX
0,10
0,05 MIN
PINS **
14
16
20
24
28
30
38
A MAX
6,50
6,50
7,50
8,50
10,50
10,50
12,90
A MIN
5,90
5,90
6,90
7,90
9,90
9,90
12,30
DIM
4040065 /E 12/01
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion not to exceed 0,15.
Falls within JEDEC MO-150
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MECHANICAL DATA
MTSS001C – JANUARY 1995 – REVISED FEBRUARY 1999
PW (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
14 PINS SHOWN
0,30
0,19
0,65
14
0,10 M
8
0,15 NOM
4,50
4,30
6,60
6,20
Gage Plane
0,25
1
7
0°– 8°
A
0,75
0,50
Seating Plane
0,15
0,05
1,20 MAX
PINS **
0,10
8
14
16
20
24
28
A MAX
3,10
5,10
5,10
6,60
7,90
9,80
A MIN
2,90
4,90
4,90
6,40
7,70
9,60
DIM
4040064/F 01/97
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion not to exceed 0,15.
Falls within JEDEC MO-153
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements,
improvements, and other changes to its products and services at any time and to discontinue any product or service without notice.
Customers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s
standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this
warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily
performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should
provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask
work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services
are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such
products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under
the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an
unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties
may be subject to additional restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service
voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business
practice. TI is not responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would
reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement
specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications
of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related
requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any
applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its
representatives against any damages arising out of the use of TI products in such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is
solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in
connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products
are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any
non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
RFID
www.ti-rfid.com
Telephony
www.ti.com/telephony
Low Power
Wireless
www.ti.com/lpw
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2007, Texas Instruments Incorporated