REF : 20090324-B SPECIFICATION FOR APPROVAL ABC'S DWG NO. PROD. SMD LINE FILTER NAME PAGE: 1 SF2012□□□□L□-□□□ ABC'S ITEM NO. Ⅰ﹒MECHANICAL DIMENSIONS： A B C A B C D E F G H I 2 D 1 : : : : : : : : : m/m m/m m/m m/m m/m m/m m/m m/m m/m 2.05±0.2 1.25±0.2 1.25±0.2 0.40 typ. 0.45 typ. 0.80 ref. 0.90 ref. 0.50 ref. 0.35 ref. F G E H 3 E I 4 I D G ( PCB Pattem ) Ⅱ﹒SCHEMATIC DIAGRAM： N1 1 2 4 3 N2 a b Ⅲ﹒MATERIALS LIST： a﹒Core：Ferrite b﹒Wire ：Enamelled copper wire ( class F ) c c﹒Terminal： Ag / Ni / Sn Peak Temp：260℃ max. Max time above 230℃ ：50sec max. Max time above 200℃ ：70sec max. d﹒Remark：Products comply with RoHS' requirements Ⅳ﹒GENERAL SPECIFICATION： b﹒Rated current：Base on temp. rise & △L/L0A=20% max. c﹒Storage temp.：-55℃ ----+125℃ Preheat Area +4.0℃ / sec max. 150 ~ 200 ℃ / 60 ~ 120sec Reflow Area Forced Cooling Area +2.0 ~ 4.0℃ -(1.0 ~ 5.0)℃ / sec max. / sec max. Peak Temperature: 260℃ 250 50sec max. Temperature ( ℃ ) a﹒Temp rise ：20℃ max Temperature Rising Area 230℃ 200 150 70sec max. 100 50 d﹒Operating temp.：-55℃----+125℃ （Temp. rise included） AR-001A 0 50 100 150 Time ( seconds ) 200 250 REF : 20090324-B SPECIFICATION FOR APPROVAL ABC'S DWG NO. PROD. NAME SMD LINE FILTER PAGE: 2 SF2012□□□□L□-□□□ ABC'S ITEM NO. Ⅴ﹒ELECTRICAL CHARACTERISTICS： Dwg. No. SF2012300YL□ -□□□ SF2012670YL□ -□□□ SF2012900YL□ -□□□ SF2012121YL□ -□□□ SF2012161YL□ -□□□ SF2012181YL□ -□□□ SF2012201YL□ -□□□ SF2012221YL□ -□□□ SF2012261YL□ -□□□ SF2012301YL□ -□□□ SF2012361YL□ -□□□ SF2012371YL□ -□□□ SF2012501YL□ -□□□ SF2012671YL□ -□□□ SF2012901YL□ -□□□ Impedance (Ω) @ 100 MHz 30±25% 67±25% 90±25% 120±25% 160±25% 180±25% 200±25% 220±25% 260±25% 300±25% 360±25% 370±25% 500±25% 670±25% 900±25% Rated ( DC ) V 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 Withstanding ( DC ) V 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 1). □：Packaging information… A：Bulk B：Taping Reel 2)."- □□□ ":Reference code 3). Impedance Test Instrument：HP4291A 4). RDC Test Instrument：CH-502AC 5). IDC Test Instrument：CH1062+CH301A AR-001A Insulation Resistance ( MΩ ) min. 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 RDC (Ω) max. 0.200 0.250 0.350 0.300 0.400 0.350 0.350 0.350 0.400 0.400 0.450 0.450 0.550 0.600 0.600 IDC ( mA ) max. 450 400 330 370 300 330 330 310 300 290 280 280 170 140 80 SPECIFICATION FOR APPROVAL REF : 20090324-B PAGE: 3 PROD. ABC'S DWG NO. SMD LINE FILTER NAME SF2012□□□□L□-□□□ ABC'S ITEM NO. Ⅵ﹒INSERTION LOSS Vs. FREQUENCY & IMPEDANCE Vs. FREQUENCY ： Normal Mode Common Mode CH1 ︱Z︱ T & B 3.5 kΩ, 1Ω 1000 901 501 671 301 121 201 100 300 901 10 501 1 300 ↑ 121 201 671 301 0.1 1 OSC 150mV START 1 MHz Common Mode AR-001A 10 100 1000 BIAS OFF STOP 1.0 GHz Normal Mode SPECIFICATION FOR APPROVAL PAGE: 4 REF : 20090324-B ABC'S DWG NO. PROD. SMD LINE FILTER NAME SF2012□□□□L□-□□□ ABC'S ITEM NO. Ⅶ﹒ELECTRICAL CHARACTERISTICS： ( 1 ) Configuration T Cover Tape A B N 2.0±0.5 D ∮C ∮C G Embossed Carrier ※Carrier Tape Width : D 4 m/m P:4 m/m End Start Leader no component 200 m/m min. Trailer no component 400 m/m min. Components User direction of feed ( 2 ) Dimensions Unit:m/m Style A 07 - 08 178 B 21±0.8 C D 13 8 G 14 +0 N 50 -0 T 16.5 ( 3 ) Q'TY & G.W. Per package Inner : Reel Series SF2012 AR-001A Q'TY (pcs) 2,000 G.W. (gw) 95 Outer : Carton Style 07 - 08 Q'TY (pcs) G.W. (Kg) SIZE (cm) 100,000 6.50 41 x 39 x 22 SPECIFICATION FOR APPROVAL REF : 20090324-B PAGE: 5 PROD. ABC'S DWG NO. SMD LINE FILTER NAME SF2012□□□□L□-□□□ ABC'S ITEM NO. Ⅷ﹒DWGING NUMBER EXPRESSION： S F 2 0 1 2 Reference code Appendix code 2 : Package Appendix code 1 : Classification Tolerance code Electrical code Dimension code Type code Appendix code 1：Product Classification L：Lead Free Standard products comply with RoHS' requirements 1 ~ 9：Lead Free Special products comply with RoHS' requirements Appendix code 2：Package Information Code AR-001A Inner package A T.B.D. B T / R ( Reel package ) Inner package Q'TY T.B.D. 2000 pcs Remark SPECIFICATION FOR APPROVAL REF : 20090324-B PAGE: 6 PROD. NAME ABC'S DWG NO. SMD LINE FILTER SF2012□□□□L□-□□□ ABC'S ITEM NO. Ⅸ﹒RELIABILITY TEST： 1-1.Environmental Performance No Item 1-1-1 Temperature Cycle Test Method Specification Appearance: No Damage Impedance: within±20% of initial value One cycle: Step Temperature (℃) 1 -25±3 2 25±2 3 85±3 4 25±2 Total: 5 cycles Time (min) 30 3 30 3 Measured After Exposure in The Room Condition For 1hrs 1-1-2 Humidity Resistance Temperature: 40±2℃ Relative Humidity: 90 ~ 95% Time: 100hrs Measured After Exposure In The Room Condition For 1hrs 1-1-3 High Temperature Resistance Temperature: 85±3℃ Time: 50Hrs Measured After Exposure In The Room Condition For 1Hrs 1-1-4 Low Temperature Resistance Temperature: -25±3℃ Time: 50Hrs Measured After Exposure In The Room Condition For 1Hrs 1-1-5 High Temperature Load Life There should be no evidence of short or open circle 1-1-6 Humidity Load Life 1-2.Mechanical Performance No Item 1-2-1 Resistance To Soldering Heat Specification Appearance: No Damage 1-2-2 Solder ability The Electrodes Shall Be At Least 90% Covered with New Solder Coating 1-2-3 Commponent Adhesion (Push Test) 2 Lbs AR-001A Temperature: 85±3℃ Load: Allowed DC Current Time: 500Hrs Temperature: 40±2℃ Relative Humidity: 90~95% Load: Allowed DC Current Time: 500Hrs Test Method 1. The Device Should Be Reflow soldered on PCB (peak 260℃±5℃ For 10 Seconds) 2. Solder Composition: Sn/Ag3.0/Cu0.5 3. Test Time: 6 minutes 1. Pre-Heating: 150℃,1min. 2. Solder Composition: Sn/Ag3.0/Cu0.5 3. Solder Temperature: 245±5℃. 4. Immersion Time: 4±1 sec. The device should be reflow soldered (230±5℃ For 10 seconds) to a tinned copper substrate. A force guauge should be applied to the side of the component. The device must withstand a minimum force of 2 pounds without a failure of the termination attached to component SPECIFICATION FOR APPROVAL REF : 20090324-B PAGE: 7 PROD. NAME ABC'S DWG NO. SMD LINE FILTER SF2012□□□□L□-□□□ ABC'S ITEM NO. Ⅹ﹒UL CARD： OBMW2 Magnet Wire-Component September 8, 2000 JUNG SHING WIRE CO LTD 231 CHUNG CHENG RD, SEC 3 JEN-TEH HSIANG, TAINAN HSIEN TAIWAN Mtl Dsg AIW CFUEWB EIAIW EILOCKY EILOCKW EIW EIW-2 FL.EILOCKY LSFFW LSUEW PEW PEY SF.FLW SF.EIW SF.BY@ SF.FLY@ SF.BLOCKBS SF.EILOCKY# SF.EILOCKBS SF.BW@ SFFW Mark Dsg ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ BC SFFY UEW-1 UEW-2 UEW-4 UEY UEY-2 OC ____ ____ Polyamideimide Polyurethane Polyesterimide Polyesterimide Polyesterimide Polyamideimide Polyamide Modified Epoxy ____ ____ Polyesterimide Polyesterimide Modified Polyester Polyurethane Polyurethane Polyester Polyester Modified Polyester Polyesterimide Modified Polyester Modified Polyester Modified Polyester Polyesterimide Polyesterimide Polyamide ____ ____ ____ ____Nylon ____ Nylon Nylon Modified Polyamide Polyamide Modified Polyamide ____ Modified Polyester Polyurethane 287806002 Mtl Dsg Coat Typ E174837 ANSI Type Temp Class MW81-C MW75C MW35C ___ ___ 220 130 200 180 200 ___ MW74-C ___ MW79-C ___ ___ MW24-C MW26C MW77C MW27-C MW27-C ___ ___ ___ 180 180 MW26C MW79 ____ ____ ____ ____ ____ ____ BC Coat Typ Polyurethane Polyurethane Polyurethane Polyurethane Polyurethane Polyurethane 155 155 A not-for-profit organization dedicated to public safety and committed to quality service Page 1 of 2 Mark Dsg 220 200 155 155 130 155 155 155 180 155 155 155 OC Polyamide ____ ____ ____ Nylon Polyamide ANSI Type Temp Class MW80C MW2-C ___ 155 105 130 130 130 130 MW75C MW28-C MW28-C @-May be suffixed by LZ; # - May be suffixed by LZ, EL or LZI. LZ - Signifies magned wires twisted together; EL - signifies base coated magnet wire laid parallel with top coat applied overall; LZL - signifies base coated magnet wire twisted together and covered with top coat overall. Marking: Company name or trademarks Recognized Component Mark. or 榮星電線 , material designation or marked designation on packaed or reel, and See General Information Preceding These Recognitions For use only in equipment where the acceptability of the combination is determined by Underwriters Laboratories Inc. 287806002 AR-001A Page 2 of 2 OBMW2⁄E174837 September 8 , 2000