SPECIFICATION FOR APPROVAL PAGE: 1 REF : PROD. NAME SHIELDED SMD POWER INDUCTOR ABC'S DWG No. SP2480□□□□L□-□□□ ABC'S ITEM No. Ⅰ﹒MECHANICAL DIMENSIONS： 1R0 C Marking B A A : 22.5±0.5 m/m B : 24.0±0.5 m/m C : 8.7 max. D : 17.6 typ. m/m m/m E : 3.3 typ. m/m F : 5.0 typ. m/m G : 7.0 typ. m/m H : 15.8 typ. m/m I : m/m 5.0 typ. D H E I I E G F Ⅱ﹒SCHEMATIC DIAGRAM： a Ⅲ﹒MATERIALS LIST： b a﹒Core：Ferrite core b﹒Wire：Ultra-Fine rectangular c Enamelled copper wire c﹒Base：UL 94V-0 d﹒Terminal：Cu / Ni / Sn e﹒Adhesive：Epoxy resin f﹒Solder wire：Sn / Cu g﹒Tape：Kapton class H Peak Temp：260℃ max. Max time above 230℃ ：50sec max. Max time above 200℃ ：70sec max. h﹒Remark：Products comply with RoHS' requirements 250 a﹒Storage temp.：-40℃ ~ +125℃ b﹒Operating temp .：-40℃ ~ +125℃ ( Temp. rise included ) c﹒Resistance to solder heat：260℃. 10 secs. AR-001A d Temperature Rising Area Preheat Area Reflow Area +4.0℃ / sec max. 150 ~ 200℃ / 60 ~ 120sec +2.0 ~ 4.0℃ / sec max. Forced Cooling Area -(1.0 ~ 5.0)℃ / sec max. Peak Temperature: 260℃ 50sec max. Temperature ( ℃ ) Ⅳ﹒GENERAL SPECIFICATION： e f 230℃ 200 150 70sec max. 100 50 0 50 100 150 Time ( seconds ) 200 250 SPECIFICATION FOR APPROVAL PAGE: 2 REF : PROD. ABC'S DWG No. SHIELDED SMD POWER INDUCTOR NAME SP2480□□□□L□-□□□ ABC'S ITEM No. Ⅴ﹒ELECTRICAL CHARACTERISTICS： Initial Inductance L0 ( uH ) Inductance at flat point L1 ( uH ) Flat point ref. (A) SP24801R0YL□-□□□ 3.0±25% 1.0±25% 8 SP24801R8YL□-□□□ 4.0±25% 1.8±25% SP24803R0YL□-□□□ 5.3±25% SP24804R0YL□-□□□ 6.5±25% DWG No. IDC (A) DC Resistance ( mΩ ) max. typ. 50 1.0 0.70 8 40 1.6 1.16 3.0±25% 8 32 2.8 2.17 4.0±25% 8 28 3.4 2.63 1). □：Packaging information … A：Bulk B：Taping Reel 2). "- □□□ ":Reference code 3). Measured Frequency of inductance is 100 KHz / 1V 4). IDC : Temp . rise 40℃ max. & △L/L0A 25% typ. @ Inductance VS. DC Superposition characteristics Inductance ( uH ) 6.0 4.0 4R0 3R0 2.0 1R8 1R0 0 20 40 DC Current ( A ) AR-001A 60 80 SPECIFICATION FOR APPROVAL REF : PAGE: 3 PROD. SHIELDED SMD POWER INDUCTOR NAME ABC'S DWG No. SP2480□□□□L□-□□□ ABC'S ITEM No. @ DC Current VS Temperature Rise 1R0 △℃ 100 75 75 50 50 25 25 0 0 0 15 30 45 60 A 3R0 △℃ 0 15 100 75 75 50 50 25 25 30 45 60 A 45 60 A 4R0 △℃ 100 0 0 0 AR-001A 1R8 △℃ 100 15 30 45 60 A 0 15 30 SPECIFICATION FOR APPROVAL REF : PAGE: 4 PROD. ABC'S DWG No. SHIELDED SMD POWER INDUCTOR NAME SP2480□□□□L□-□□□ ABC'S ITEM No. Ⅵ﹒PACKAGING INFORMATION： ( 1 ) Configuration T Cover Tape A B N 2.0±0.5 ∮C ∮C D G Embossed Carrier 4 m/m P:28 m/m ※Carrier tape width : D End Start 1R0 1R0 Leader no component 200 m/m min. 1R0 1R0 Trailer no component 400 m/m min. Components User direction of feed ( 2 ) Dimensions Unit:m/m Style A B C 13 - 44 330 21.0±0.8 13.0 -0.2 +0.5 D 44.0±0.3 G +2.0 44.4 -0 N 100 T -0 50.4 +0 ( 3 ) Q'TY & G.W. Per package Inner : Reel Series SP2480 AR-001A Q'TY (pcs) 150 Outer : Carton G.W. (gw) Style Q'TY (pcs) G.W. (Kg) Size (cm) 2275 13 - 44 600 11.90 395 x 395 x 265 SPECIFICATION FOR APPROVAL PAGE: 5 REF : PROD. SHIELDED SMD POWER INDUCTOR NAME ABC'S DWG No. SP2480□□□□L□-□□□ ABC'S ITEM No. Ⅶ﹒DWGING NUMBER EXPRESSION： P S 2 4 8 0 Reference code Appendix code 2 : Package Appendix code 1 : Classification Tolerance code Electrical code Dimension code Type code Appendix code 1：Product Classification L：Lead Free Standard products comply with RoHS' requirements 1 ~ 9：Lead Free Special products comply with RoHS' requirements Appendix code 2：Package Information Code AR-001A Inner package Inner package Q'TY A T.B.D. T.B.D. B T / R ( Reel package ) 150 pcs Remark SPECIFICATION FOR APPROVAL PAGE: 6 REF : PROD. NAME SHIELDED SMD POWER INDUCTOR ABC'S DWG No. SP2480□□□□L□-□□□ ABC'S ITEM No. Ⅷ﹒RELIABILITY TEST： Test item Solderability Thermal shock test ( Temp. cycle ) Specification Test condition More than 90% of the terminal electrode Shall be covered With fresh solder. Preheat : 150±25℃ for 60 seconds Solder : Sn96.5 / Ag3 / Cu0.5 or equivalent Solder temp. : 250±5℃ Flux : Rosin Dip time : 4±1 seconds Inductance shall not change more than ±20% Room temp. 15 minutes -25±2 ℃ 30 minutes Room temp. 15 minutes 85±2 ℃ Total : 50 cycles Humidity Resistance test Temperature : 40±2℃ Humidity : 90 ~ 95% Applied current : Per spec. Time : 500 hours High temp. Resistance test Temperature : 85±2℃ Applied current : Per spec. Time : 500 hours AR-001A 30 minutes SPECIFICATION FOR APPROVAL REF : PROD. NAME PAGE: 7 SHIELDED SMD POWER INDUCTOR ABC'S DWG No. SP2480□□□□L□-□□□ ABC'S ITEM No. Ⅸ﹒UL CARD： July 30, 2001 OBMW2 Magnet Wire-Component E218212 UNIMAC LTD Mark Dsg —— —— —— Mtl Dsg AIW FT-AIWU SFT-AIWU Coat Typ BC Polyamide-imide Polyamide-imide Polyamide-imide ANSI Type —— —— —— OC —— —— —— Temp Class 220 220 220 # - May be followed by LZ to denote Litz wire. Marking：Company name, material designation or marked designation on package or reel, and Recognized Component Mark. 8/27/2001 Underwriters Laboratories Inc. Card 1 of 3 / Card 2 of 3 August 31, 2002 QMFZ2 Plastics-Component E91944 NIPPON PETROCHEMICALS CO LTD H Min W Thk Flame I Mterial Dsg Color mm Class Liquid Crystal Polyester (LCP), glass filled, furnished as pellets. HM-402 NC , BK 0.30 V-0 ___ H A I ___ Elec 130 H V T R D 4 9 5 C T I ___ ___ ___ RTI Mech Imp Slr 130 130 (a)-Virgin and Regrind up to 50% have the same basic characteristics. r1-Virgin and Regrind from 1 to 50% by weight incl. have the same Flame characleristics, Tensile Impact, Tensile Strength and Heat Deflection in natural color only. r2-Virgin and Regrind from 26-50% by weight inclusive for the colors NC, and BK liave the same Flame, and Tensile Impact characteristics. r3-Virgin and Regrind from 26-50% by weight inclusive have the same Flame and Tensile lmpact characteristics. Marking：Company name or trademark designation on container, wrapper or finished part. 10/15/2002 AR-001A Underwriters Laboratories Inc. and material Card 8 of 9