600 Series
Serial Annunciator Driver
The Gamewell-FCI 600 systems can accommodate up to
64 devices connected to the serial communications port. In
addition to the serial annunciator drives (SAN), these
devices include remote annunciator (RAN) and remote
printer interface (RPI). This combination of devices comprise the Gamewell-FCI status control network. Since each
device contains its own microprocessor, each can be programmed independently. A series of devices can be programmed directly over the network from a single device,
saving valuable installation time. Programming is accomplished via Windows®-based configuration software.
Each SAN input point can activate up to five output points
for matrix annunciation. There are two basic models available, the SAN and the SAN-RC. The SAN-16 is equipped
with 16 freely programmable outputs which can be used for
remote control or monitoring, expandable to 128 points
using PDM modules.
The SAN-16-RC has all of the features of the SAN-16, plus
the ability to read inputs into the system. The SAN-16-RC
has provisions for four inputs for: remote acknowledge,
reset, signal silence, and lamp test. In addition to the basic
16 outputs, there are eight (8) common outputs for: common system alarm, common system trouble, AC power,
communications, action required LED prompts for system
acknowledge, reset and signal silence, and a driver for a
local audible.
The 600 Series serial annunciator driver (SAN) is used to
light a lamp or LED in an annunciator. It also provides a
switched positive output per point for interface with building
automation systems or driving relays. Each device is capable of interpreting the instructions from the main CPU, initiating its own programmed response, and retransmitting the
instructions to the next device.
Up to 64 devices supported on a single 600 Series
control panel.
Windows®-based field programming.
Dual optically isolated serial ports.
Can interface with building automation systems
via standard ASCII communication.
Microprocessor based.
Expandable in 16 point increments to 128 points.
Allows remote system control.
Mounting track included.
An ISO 9000-2000 Company
The status control network, including SAN units, is connected to the main 600 Series control panel via an RS-232
data communication line. The SIM-232 module is used to
Microsoft® Windows® is a registered trademark of Microsoft® Corporation.
12 Clintonville Road, Northford, CT 06472-1610 USA • Tel: (203) 484-7161 • Fax: (203) 484-7118
Specifications are for information only, are not intended for installation purposes, and are subject to change without notice. No responsibility is assumed by Gamewell-FCI for their use.
©2007 Honeywell International Inc. All rights reserved.
CS-2027 Rev. A page 1 of 2
provide an isolated RS-232 output from the main CPU of
the 600 Series system panels. The IF602 and IF610 panels
have built-in RS-232 ports.
Ordering Information
The SAN units provide a means for remote annunciation
and control of the system via a simple RS-232 connection.
These driver units fit neatly into an annunciator unit and
can be used to drive the LED or incandescent lights of a
standard or graphic-type annunciator. When it is necessary
for remote system control, the SAN-16-RC provides for up
to eight inputs for system control. Any or all inputs may be
used to customize any given command station’s capabilities.
The SAN units can also be used to interface with other
building systems via ASCII or where dry contacts or a
switched output is required. The SAN’s outputs can be
used to drive a relay to interface or control virtually any
remote point or group of points.
Engineer’s Specifications
Remote annunciation and control for the main control panel
shall be supplied where indicated. Remote annunciation
and control shall be accomplished via the RS-232 data
communications line. It shall be possible to add up to 64
devices to the communication line. Each device shall be
capable of driving up to 128 points. It shall be possible to
mix annunciators, printers and LCD alphanumeric displays
on a single line without the need for special software.
Devices shall not be placement sensitive. All devices shall
be individually field programmable and independent from
each other. The device shall be Gamewell-FCI part
Serial annunciator driver module, main driver
with 16-outputs.
Serial annunciator driver module, specify
number of outputs in 16-point increments
(i.e., SAN-32, SAN-48, SAN-128). Includes
mounting track and interconnect cables.
Contact the Gamewell-FCI Technical
Support for details.
SAN-16-RC Serial annunciator driver with four-remote
control inputs, eight (8) common outputs and
SAN-#-RC Serial annunciator driver with four- remote
control inputs, eight (8) common outputs and
a specifiable number of outputs in 16-point
increments (i.e., SAN-32-RC, SAN-48-RC,
SAN-128-RC). Includes mounting track and
interconnect cables.
Contact Gamewell-FCI Technical Support for
Point driver module for field-expanding
serial annunciator drivers, 16 outputs.
Required serial interface module, mounts in
600 Series control 632, 654, and 658 to supply RS-232 ouputs.
Note: This model is not required for use with
the IF602 and IF610 Systems.
Programming cable (Programmed via a
Windows®-based SAN program). Found on
the Gamewell-FCI website.
Note: This program is only available to
Gamewell-FCI authorized distributors.
Serial Annunciator
Basic SAN and SAN-RC provide 16point drives.
Input Power:
Standby Current: 0.04 A max.
Alarm Current:
2.0 A max.
Output Power:
0.040 A max. per output.
12” W x 4” H x 2” D
(30.5 W x 10.2 H x 5.1 D cm)
PDM-16 Point Drive Module
Input Power:
From SAN Module
Standby Current: 0.002 A
Alarm Current:
0.002 A
12 Clintonville Road, Northford, CT 06472-1610 USA • Tel: (203) 484-7161 • Fax: (203) 484-7118
CS-2027 Rev. A page 2 of 2