RCD PWLL10WW-102

5W TO 50 WATT POWER RESISTORS
CERAMIC ENCASED, RADIAL LEADS
RoHS
Term.W is
RoHS
compliant
& 260°C
compatible
RESISTORSCAPACITORSCOILSDELAY LINES
PWLL & PWH SERIES
Low cost, fireproof construction
0.1Ω to 150KΩ, ±5% is standard (0.5% to 10% avail.)
PWLL and PWH resistors are designed for general purpose and
semi-precision power applications. The ceramic construction is
fireproof and resistant to moisture & solvents. The internal element
is wirewound on lower values, power film on higher values
(depending on options, e.g. opt. P parts are always WW). If a
specific construction is preferred, specify opt.’WW’ for wirewound,
opt.’M’ for power film (not available in all values).
OPTIONS
Option X: Non-Inductive
Option P: Increased pulse capability
Option G: 1/4x.032” male fast-on terminals (PWH & PWHM15-50)
RCD
Type
1
2
3
4
Wattage
(25°C )
R esis.
R an g e
Max.C ont.
Working
Voltage 1
L (max)
W (max)
H (max)
LS
P1
P2
P3 3 ±.06 [1.5]
D IMEN SION S: Inch (mm)
PWLL5
5
.1Ω-50K
350
1.10 [28]
.413 [10.5]
.413 [10.5]
.59±.06 [15±1.5]
.055±.01[1.4±.25]
.11 [2.8] mi n
.413 [10.5]3
PWLL7
7
.1Ω-100K
500
1.42 [36]
.413 [10.5]
.413 [10.5]
.89±.06[22.5±1.5]
.055±.01[1.4±.25]
.11 [2.8] mi n
.413 [10.5]3
PWLL10
10
.2Ω-100K
700
1.93 [49]
.413 [10.5]
.413 [10.5]
4
1.26±.06 [32±1.5]
.055±.01[1.4±.25]
.11 [2.8] mi n
.413 [10.5]3
PWLL15
15
.5Ω-100K
750
1.95 [49.5]
.532 [13.5]
.532 [13.5]
1.26±.08 [32±2]
.108±.012[2.75±.3]
.15 [3.8] mi n
.591 [15] 3
PWLL25
25
.591 [15]
.591 [15]
1.77±.08 [45±2]
.108±.012[2.75±.3]
.15 [3.8] mi n
.591 [15 ] 3
.5Ω-100K
1000
2.54[ 64.5]
PWH10, PWHM10
10
2
.5Ω-50K
700
1.97 [50]
.433 [11.0]
.473 [12.5]
1.30±.08 [33±2]
.470 ± .04 [12 ±1]
.22 ±.04 [5.5±1]
.275 [7]
PWH15, PWHM15
15
2
.5Ω-150K
750
1.97 [50]
.531 [13.5]
.572 [14.5]
1.30±.08 [33±2]
.470 ± .04 [12 ±1]
.24 ±.04 [6 ±1]
.315 [8 ]
PWH25, PWHM25
25
2
.5Ω-150K
1000
2.56 [65]
.598 [15.2]
.591 [15]
1.77±.12 [45±3]
.470 ± .04 [12 ±1]
.24 ±.04 [6 ±1]
.315 [8 ]
PWH40, PWHM40
40
2
1Ω-2K
1000
3.03 [77]
.787 [20.0]
.847 [21.5]
2.17±.08 [55±3]
.69 ±.04 [17.5 ±1]
.28 ±.06 [7±1.5]
.394 [10]
PWH50, PWHM50
50
2
1Ω-2K
1000
3.62 [92]
.787 [20.0]
.847 [21.5]
2.72±.12 [69±3]
.69 ±.04 [17.5 ±1]
.28 ±.06 [7±1.5]
.394 [10]
Max voltage determined by E=(PR)1/2, E not to exceed MCWV (increased voltage levels avail).
When mounted on suitable heatsink, PWHM wattage may be increased by 25% (use thermal grease)
PW5LL,7LL,10LL also avail. with 15 or 25mm standoff terminals (specify opt.15 or 25); PW15LL & 25LL avail. with 10.5mm or 30mm, specify options 10 or 30.
1.39”[35mm] avail., specify opt. 35
PWLL
PERFORMANCE (typ.)
←W→
L
Temperature
CoefT25 toT100
↑
H
↓
↓
→
± .005
← .020
[.508 ± .127]
12
12
12
12
LS
5 - 10W= 10.5mm (15 & 25mm avail.)3
P3
12
12
12
12
15 - 25W= 15mm (10.5 & 30mm avail.)3
P2
→ ← P1
Suggested Mounting Holes:
5 to10W =.032 [.8] W x .07[1.8] L
15 to 25W = .040 [1] W x .13 [3.3] L
PWH
↓
Opt.G 1/4x.032 male terminals
avail. on PWH & PWHM15-50
.10 [2.5]
dia. typ.
.31 [8]
min.
LS
↑
.24 [6] →
←
↓
P1
Operating Temp.
Terminal Strength
Dielectric Strength
5 Sec. overload ( ≤1.5x max V)
Moisture Resistance
High Temp. Exposure
Load Life (1000 hours)
Temperature Cycling
Shock and Vibration
Inductance (standard parts
are inductive, specify opt.X
for low inductance
version)
Derating
100ppm/°C typ., 300ppm max *
200ppm/°C typ., 600ppm max. *
-55° to +235° C (275° C avail)
5 lbs. minimum
1000V
3X rated wattage (Opt. WW = 5X)
3.0%
1.0%
3.0%
2.0%
1.0%
Opt.X 25W & smaller: ≤50Ω=0.3uH max,
>50Ω= 0.6uH max.
Opt. X 30W & larger: ≤50Ω=1uH max,
>50Ω= 2uH max). Reduced induc. avail.
100 to 140°C typ at 50% rated power, 200
to 250°C typ at full rated power
Derate wattage and voltage by
.48%/°Cabove 25° C
* Tightened TC’s available, consult factory
←W →
P/N DESIGNATION:
PWH 10
- 102 - J B W
RCD Type (PWLL, PWH, PWHM)
PWHM (PWH with metal mounting bracket)
.156± .032
[4 ± .8]
Below 1Ω
Temperature Rise
↑
H
L
1Ω & above
Wattage
.12 [3]
Options: X, WW, P, M, G, 10, 15, 25, 30 (leave blank if std)
P2
P3
.086 [2.2]
Note: for unbent flange
specify opt.U (add .12”
[3mm] to dim P2)
Resis.Code .5%-1%: 3 signif. figures & multiplier,
e.g. R100=0.1Ω, 1R00=1Ω, 10R0=10Ω, 1000=100Ω, 1001=1K
Resis.Code 2%-10%: 2 signif. figures & multiplier,
e.g. R10=0.1Ω, 1R0=1Ω, 100=10Ω, 101=100Ω,102=1K, etc.
Tolerance: D=0.5%,F=1%,G=2%,J=5%(std),K=10%
Packaging: B = Bulk (standard)
Termination: W= Lead-free, Q= Tin/Lead, leave blank if either is acceptable
RCD Components Inc, 520 E.Industrial Park Dr, Manchester, NH, USA 03109 rcdcomponents.com Tel: 603-669-0054 Fax: 603-669-5455 Email:[email protected]
FA051D
49
Sale of this product is in accordance with GF-061. Specifications subject to change without notice.